Add a platform clocksource by adapting the existing arch_gettimeoffset
implementation.
Normally the MFP timer C interrupt flag would be used to check for
timer counter wrap-around. Unfortunately, that flag gets cleared by the
MFP itself (due to automatic End-of-Interrupt mode). This means that
mfp_timer_c_handler() and atari_read_clk() must race when accounting
for counter wrap-around.
That problem is avoided by effectively stopping the clock when it might
otherwise jump backwards (due to interrupt latency). Note that this may
affect clock accuracy.
After the timer interrupt is asserted, wait for the counter to be
reloaded so that atari_read_clk() will not see the intermediate state
as that would cause the clock to jump backwards.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The functions that implement arch_gettimeoffset are re-used by
new clocksource drivers in subsequent patches.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
These dummy implementations are no better than
default_arch_gettimeoffset() so remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This resolves some bugs that affect VIA timer counter accesses.
Avoid lost interrupts caused by reading the counter low byte register.
Make allowance for the fact that the counter will be decremented to
0xFFFF before being reloaded.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Some platforms execute their timer handler with the interrupt priority
level set below 6. That means the handler could be interrupted by another
driver and this could lead to re-entry of the timer core.
Avoid this by use of local_irq_save/restore for timer interrupt dispatch.
This provides mutual exclusion around the timer interrupt flag access
which is needed later in this series for the clocksource conversion.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.DEB.2.21.1811131407120.2697@nanos.tec.linutronix.de
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
syscall_get_arch() is required to be implemented on all architectures
in addition to already implemented syscall_get_nr(),
syscall_get_arguments(), syscall_get_error(), and
syscall_get_return_value() functions in order to extend the generic
ptrace API with PTRACE_GET_SYSCALL_INFO request.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: Elvira Khabirova <lineprinter@altlinux.org>
Cc: Eugene Syromyatnikov <esyr@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-audit@redhat.com
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge misc updates from Andrew Morton:
- a few misc things
- the rest of MM
- remove flex_arrays, replace with new simple radix-tree implementation
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (38 commits)
Drop flex_arrays
sctp: convert to genradix
proc: commit to genradix
generic radix trees
selinux: convert to kvmalloc
md: convert to kvmalloc
openvswitch: convert to kvmalloc
of: fix kmemleak crash caused by imbalance in early memory reservation
mm: memblock: update comments and kernel-doc
memblock: split checks whether a region should be skipped to a helper function
memblock: remove memblock_{set,clear}_region_flags
memblock: drop memblock_alloc_*_nopanic() variants
memblock: memblock_alloc_try_nid: don't panic
treewide: add checks for the return value of memblock_alloc*()
swiotlb: add checks for the return value of memblock_alloc*()
init/main: add checks for the return value of memblock_alloc*()
mm/percpu: add checks for the return value of memblock_alloc*()
sparc: add checks for the return value of memblock_alloc*()
ia64: add checks for the return value of memblock_alloc*()
arch: don't memset(0) memory returned by memblock_alloc()
...
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68knommu update from Greg Ungerer:
"Only a single change to provide platform side support for the eDMA
hardware module on the ColdFire MCF5441X SoC"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: add ColdFire mcf5441x eDMA platform support
This Kconfig option was removed during v4.19 development in commit
771c035372 ("deprecate the '__deprecated' attribute warnings entirely
and for good") so there's no point to keep it in defconfigs any longer.
FWIW defconfigs were patched with:
--------------------------->8----------------------
find . -name *_defconfig -exec sed -i '/CONFIG_ENABLE_WARN_DEPRECATED/d' {} \;
--------------------------->8----------------------
Link: http://lkml.kernel.org/r/20190128152434.41969-1-abrodkin@synopsys.com
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
The PG_reserved flag is cleared from memory that is part of the kernel
image (and therefore marked as PG_reserved). Avoid using PG_reserved
directly.
Link: http://lkml.kernel.org/r/20190114125903.24845-6-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull year 2038 updates from Thomas Gleixner:
"Another round of changes to make the kernel ready for 2038. After lots
of preparatory work this is the first set of syscalls which are 2038
safe:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
The syscall numbers are identical all over the architectures"
* 'timers-2038-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
riscv: Use latest system call ABI
checksyscalls: fix up mq_timedreceive and stat exceptions
unicore32: Fix __ARCH_WANT_STAT64 definition
asm-generic: Make time32 syscall numbers optional
asm-generic: Drop getrlimit and setrlimit syscalls from default list
32-bit userspace ABI: introduce ARCH_32BIT_OFF_T config option
compat ABI: use non-compat openat and open_by_handle_at variants
y2038: add 64-bit time_t syscalls to all 32-bit architectures
y2038: rename old time and utime syscalls
y2038: remove struct definition redirects
y2038: use time32 syscall names on 32-bit
syscalls: remove obsolete __IGNORE_ macros
y2038: syscalls: rename y2038 compat syscalls
x86/x32: use time64 versions of sigtimedwait and recvmmsg
timex: change syscalls to use struct __kernel_timex
timex: use __kernel_timex internally
sparc64: add custom adjtimex/clock_adjtime functions
time: fix sys_timer_settime prototype
time: Add struct __kernel_timex
time: make adjtime compat handling available for 32 bit
...
- VLA removal,
- Gcc-8.x build fixes,
- Small improvements and cleanups,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXHk4BBUcZ2VlcnRAbGlu
dXgtbTY4ay5vcmcACgkQisJQ/WRJ8XAF4wEAn31Bsn7R8Szn/TtilxBL0GQV3eeC
rGtX96FrGurDSlYA/1RmgYffJsb/Rlia9ejb8/rWPsEEZn8ngZ2T2YjRHwUA
=665T
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- VLA removal
- gcc-8.x build fixes
- small improvements and cleanups
- defconfig updates
* tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Add -ffreestanding to CFLAGS
m68k/apollo: Fix comment in Makefile
dio: Fix buffer overflow in case of unknown board
m68k/defconfig: Update defconfigs for v5.0-rc1
m68k/atari: Avoid VLA use in atari_switches_setup()
m68k: Avoid VLA use in mangle_kernel_stack()
m68k/mac: Use '030 reset method on SE/30
m68k/mac: Remove obsolete comment
m68k/mac: Skip VIA port setup unless RTC is connected
m68k/mac: Clean up unused timer definitions
m68k/defconfig: Drop NET_VENDOR_<FOO>=n
We're (finally) phasing out a.out support for good. As Borislav Petkov
points out, we've supported ELF binaries for about 25 years by now, and
coredumping in particular has bitrotted over the years.
None of the tool chains even support generating a.out binaries any more,
and the plan is to deprecate a.out support entirely for the kernel. But
I want to start with just removing the core dumping code, because I can
still imagine that somebody actually might want to support a.out as a
simpler biinary format.
Particularly if you generate some random binaries on the fly, ELF is a
much more complicated format (admittedly ELF also does have a lot of
toolchain support, mitigating that complexity a lot and you really
should have moved over in the last 25 years).
So it's at least somewhat possible that somebody out there has some
workflow that still involves generating and running a.out executables.
In contrast, it's very unlikely that anybody depends on debugging any
legacy a.out core files. But regardless, I want this phase-out to be
done in two steps, so that we can resurrect a.out support (if needed)
without having to resurrect the core file dumping that is almost
certainly not needed.
Jann Horn pointed to the <asm/a.out-core.h> file that my first trivial
cut at this had missed.
And Alan Cox points out that the a.out binary loader _could_ be done in
user space if somebody wants to, but we might keep just the loader in
the kernel if somebody really wants it, since the loader isn't that big
and has no really odd special cases like the core dumping does.
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function). It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.
Which in the kernel is always KERNEL_DS.
Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.
Roughly scripted with
git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'
plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.
The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.
Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a follow-up to the y2038 syscall patches already merged in the tip
tree. As the final 32-bit RISC-V syscall ABI is still being decided on,
this is the last chance to make a few corrections to leave out interfaces
based on 32-bit time_t along with the old off_t and rlimit types.
The series achieves this in a few steps:
- A couple of bug fixes for minor regressions I introduced
in the original series
- A couple of older patches from Yury Norov that I had never
merged in the past, these fix up the openat/open_by_handle_at and
getrlimit/setrlimit syscalls to disallow the old versions of off_t
and rlimit.
- Hiding the deprecated system calls behind an #ifdef in
include/uapi/asm-generic/unistd.h
- Change arch/riscv to drop all these ABIs.
Originally, the plan was to also leave these out on C-Sky, but that now
has a glibc port that uses the older interfaces, so we need to leave
them in place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/iFA
-----END PGP SIGNATURE-----
Merge tag 'y2038-syscall-abi' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull additional syscall ABI cleanup for y2038 from Arnd Bergmann:
This is a follow-up to the y2038 syscall patches already merged in the tip
tree. As the final 32-bit RISC-V syscall ABI is still being decided on,
this is the last chance to make a few corrections to leave out interfaces
based on 32-bit time_t along with the old off_t and rlimit types.
The series achieves this in a few steps:
- A couple of bug fixes for minor regressions I introduced
in the original series
- A couple of older patches from Yury Norov that I had never
merged in the past, these fix up the openat/open_by_handle_at and
getrlimit/setrlimit syscalls to disallow the old versions of off_t
and rlimit.
- Hiding the deprecated system calls behind an #ifdef in
include/uapi/asm-generic/unistd.h
- Change arch/riscv to drop all these ABIs.
Originally, the plan was to also leave these out on C-Sky, but that now
has a glibc port that uses the older interfaces, so we need to leave
them in place.
All new 32-bit architectures should have 64-bit userspace off_t type, but
existing architectures has 32-bit ones.
To enforce the rule, new config option is added to arch/Kconfig that defaults
ARCH_32BIT_OFF_T to be disabled for new 32-bit architectures. All existing
32-bit architectures enable it explicitly.
New option affects force_o_largefile() behaviour. Namely, if userspace
off_t is 64-bits long, we have no reason to reject user to open big files.
Note that even if architectures has only 64-bit off_t in the kernel
(arc, c6x, h8300, hexagon, nios2, openrisc, and unicore32),
a libc may use 32-bit off_t, and therefore want to limit the file size
to 4GB unless specified differently in the open flags.
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yury Norov <ynorov@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
This series finally gets us to the point of having system calls with
64-bit time_t on all architectures, after a long time of incremental
preparation patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures
using the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call
that includes a 'struct timespec' argument, or a structure containing
a timespec or (in case of clock_adjtime) timeval. Not included here
are new versions of getitimer/setitimer and getrusage/waitid, which
are planned for the future but only needed to make a consistent API
rather than for correct operation beyond y2038. These four system
calls are based on 'timeval', and it has not been finally decided
what the replacement kernel interface will use instead.
So far, I have done a lot of build testing across most architectures,
which has found a number of bugs. Runtime testing so far included
testing LTP on 32-bit ARM with the existing system calls, to ensure
we do not regress for existing binaries, and a test with a 32-bit
x86 build of LTP against a modified version of the musl C library
that has been adapted to the new system call interface [3].
This library can be used for testing on all architectures supported
by musl-1.1.21, but it is not how the support is getting integrated
into the official musl release. Official musl support is planned
but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IZVb
-----END PGP SIGNATURE-----
Merge tag 'y2038-new-syscalls' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull y2038 - time64 system calls from Arnd Bergmann:
This series finally gets us to the point of having system calls with 64-bit
time_t on all architectures, after a long time of incremental preparation
patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures using
the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call that
includes a 'struct timespec' argument, or a structure containing a timespec
or (in case of clock_adjtime) timeval. Not included here are new versions
of getitimer/setitimer and getrusage/waitid, which are planned for the
future but only needed to make a consistent API rather than for correct
operation beyond y2038. These four system calls are based on 'timeval', and
it has not been finally decided what the replacement kernel interface will
use instead.
So far, I have done a lot of build testing across most architectures, which
has found a number of bugs. Runtime testing so far included testing LTP on
32-bit ARM with the existing system calls, to ensure we do not regress for
existing binaries, and a test with a 32-bit x86 build of LTP against a
modified version of the musl C library that has been adapted to the new
system call interface [3]. This library can be used for testing on all
architectures supported by musl-1.1.21, but it is not how the support is
getting integrated into the official musl release. Official musl support is
planned but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
The system call tables have diverged a bit over the years, and a number
of the recent additions never made it into all architectures, for one
reason or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all
architectures but that we definitely want there. This includes
{,f}statfs64() and get{eg,eu,g,p,u,pp}id() on alpha, which have
been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like
what we do on other architectures, while keeping the 31-bit
pointer extension. This was merged as a shared branch by the
s390 maintainers and is included here in order to base the other
patches on top.
- Add the separate ipc syscalls on all architectures that
traditionally only had sys_ipc(). This version is done without
support for IPC_OLD that is we have in sys_ipc. The
new semtimedop_time64 syscall will only be added here, not
in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably
don't need everywhere, in particular pkey_* and rseq,
for the purpose of symmetry: if it's in asm-generic/unistd.h,
it makes sense to have it everywhere. I expect that any future
system calls will get assigned on all platforms together, even
when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future
calls. In combination with the generated tables, this hopefully
makes it easier to add new calls across all architectures
together.
All of the above are technically separate from the y2038 work,
but are done as preparation before we add the new 64-bit time_t
system calls everywhere, providing a common baseline set of system
calls.
I expect that glibc and other libraries that want to use 64-bit
time_t will require linux-5.1 kernel headers for building in
the future, and at a much later point may also require linux-5.1
or a later version as the minimum kernel at runtime. Having a
common baseline then allows the removal of many architecture or
kernel version specific workarounds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=s4wf
-----END PGP SIGNATURE-----
Merge tag 'y2038-syscall-cleanup' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull preparatory work for y2038 changes from Arnd Bergmann:
System call unification and cleanup
The system call tables have diverged a bit over the years, and a number of
the recent additions never made it into all architectures, for one reason
or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all architectures
but that we definitely want there. This includes {,f}statfs64() and
get{eg,eu,g,p,u,pp}id() on alpha, which have been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like what we
do on other architectures, while keeping the 31-bit pointer
extension. This was merged as a shared branch by the s390 maintainers
and is included here in order to base the other patches on top.
- Add the separate ipc syscalls on all architectures that traditionally
only had sys_ipc(). This version is done without support for IPC_OLD
that is we have in sys_ipc. The new semtimedop_time64 syscall will only
be added here, not in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably don't need
everywhere, in particular pkey_* and rseq, for the purpose of symmetry:
if it's in asm-generic/unistd.h, it makes sense to have it everywhere. I
expect that any future system calls will get assigned on all platforms
together, even when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future calls. In
combination with the generated tables, this hopefully makes it easier to
add new calls across all architectures together.
All of the above are technically separate from the y2038 work, but are done
as preparation before we add the new 64-bit time_t system calls everywhere,
providing a common baseline set of system calls.
I expect that glibc and other libraries that want to use 64-bit time_t will
require linux-5.1 kernel headers for building in the future, and at a much
later point may also require linux-5.1 or a later version as the minimum
kernel at runtime. Having a common baseline then allows the removal of many
architecture or kernel version specific workarounds.
-----BEGIN PGP SIGNATURE-----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=tuL6
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190209' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph, fixing namespace locking when
dealing with the effects log, and a rapid add/remove issue (Keith)
- blktrace tweak, ensuring requests with -1 sectors are shown (Jan)
- link power management quirk for a Smasung SSD (Hans)
- m68k nfblock dynamic major number fix (Chengguang)
- series fixing blk-iolatency inflight counter issue (Liu)
- ensure that we clear ->private when setting up the aio kiocb (Mike)
- __find_get_block_slow() rate limit print (Tetsuo)
* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
blktrace: Show requests without sector
fs: ratelimit __find_get_block_slow() failure message.
m68k: set proper major_num when specifying module param major_num
libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
aio: initialize kiocb private in case any filesystems expect it.
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds 21 new system calls on each ABI that has 32-bit time_t
today. All of these have the exact same semantics as their existing
counterparts, and the new ones all have macro names that end in 'time64'
for clarification.
This gets us to the point of being able to safely use a C library
that has 64-bit time_t in user space. There are still a couple of
loose ends to tie up in various areas of the code, but this is the
big one, and should be entirely uncontroversial at this point.
In particular, there are four system calls (getitimer, setitimer,
waitid, and getrusage) that don't have a 64-bit counterpart yet,
but these can all be safely implemented in the C library by wrapping
around the existing system calls because the 32-bit time_t they
pass only counts elapsed time, not time since the epoch. They
will be dealt with later.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The time, stime, utime, utimes, and futimesat system calls are only
used on older architectures, and we do not provide y2038 safe variants
of them, as they are replaced by clock_gettime64, clock_settime64,
and utimensat_time64.
However, for consistency it seems better to have the 32-bit architectures
that still use them call the "time32" entry points (leaving the
traditional handlers for the 64-bit architectures), like we do for system
calls that now require two versions.
Note: We used to always define __ARCH_WANT_SYS_TIME and
__ARCH_WANT_SYS_UTIME and only set __ARCH_WANT_COMPAT_SYS_TIME and
__ARCH_WANT_SYS_UTIME32 for compat mode on 64-bit kernels. Now this is
reversed: only 64-bit architectures set __ARCH_WANT_SYS_TIME/UTIME, while
we need __ARCH_WANT_SYS_TIME32/UTIME32 for 32-bit architectures and compat
mode. The resulting asm/unistd.h changes look a bit counterintuitive.
This is only a cleanup patch and it should not change any behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This is the big flip, where all 32-bit architectures set COMPAT_32BIT_TIME
and use the _time32 system calls from the former compat layer instead
of the system calls that take __kernel_timespec and similar arguments.
The temporary redirects for __kernel_timespec, __kernel_itimerspec
and __kernel_timex can get removed with this.
It would be easy to split this commit by architecture, but with the new
generated system call tables, it's easy enough to do it all at once,
which makes it a little easier to check that the changes are the same
in each table.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When calling register_blkdev() with specified major
device number, the return code is 0 on success.
So it seems not correct direct assign return code to
variable major_num in this case.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most architectures do not export shmparam.h to user-space.
$ find arch -name shmparam.h | sort
arch/alpha/include/asm/shmparam.h
arch/arc/include/asm/shmparam.h
arch/arm64/include/asm/shmparam.h
arch/arm/include/asm/shmparam.h
arch/csky/include/asm/shmparam.h
arch/ia64/include/asm/shmparam.h
arch/mips/include/asm/shmparam.h
arch/nds32/include/asm/shmparam.h
arch/nios2/include/asm/shmparam.h
arch/parisc/include/asm/shmparam.h
arch/powerpc/include/asm/shmparam.h
arch/s390/include/asm/shmparam.h
arch/sh/include/asm/shmparam.h
arch/sparc/include/asm/shmparam.h
arch/x86/include/asm/shmparam.h
arch/xtensa/include/asm/shmparam.h
Strangely, some users of the asm-generic wrapper export shmparam.h
$ git grep 'generic-y += shmparam.h'
arch/c6x/include/uapi/asm/Kbuild:generic-y += shmparam.h
arch/h8300/include/uapi/asm/Kbuild:generic-y += shmparam.h
arch/hexagon/include/uapi/asm/Kbuild:generic-y += shmparam.h
arch/m68k/include/uapi/asm/Kbuild:generic-y += shmparam.h
arch/microblaze/include/uapi/asm/Kbuild:generic-y += shmparam.h
arch/openrisc/include/uapi/asm/Kbuild:generic-y += shmparam.h
arch/riscv/include/asm/Kbuild:generic-y += shmparam.h
arch/unicore32/include/uapi/asm/Kbuild:generic-y += shmparam.h
The newly added riscv correctly creates the asm-generic wrapper
in the kernel space, but the others (c6x, h8300, hexagon, m68k,
microblaze, openrisc, unicore32) create the one in the uapi directory.
Digging into the git history, now I guess fcc8487d47 ("uapi:
export all headers under uapi directories") was the misconversion.
Prior to that commit, no architecture exported to shmparam.h
As its commit description said, that commit exported shmparam.h
for c6x, h8300, hexagon, m68k, openrisc, unicore32.
83f0124ad8 ("microblaze: remove asm-generic wrapper headers")
accidentally exported shmparam.h for microblaze.
This commit unexports shmparam.h for those architectures.
There is no more reason to export include/uapi/asm-generic/shmparam.h,
so it has been moved to include/asm-generic/shmparam.h
Link: http://lkml.kernel.org/r/1546904307-11124-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Mark Salter <msalter@redhat.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures define system call numbers for the rseq and pkey system
calls, even when they don't support the features, and perhaps never will.
Only a few architectures are missing these, so just define them anyway
for consistency. If we decide to add them later to one of these, the
system call numbers won't get out of sync then.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The IPC system call handling is highly inconsistent across architectures,
some use sys_ipc, some use separate calls, and some use both. We also
have some architectures that require passing IPC_64 in the flags, and
others that set it implicitly.
For the addition of a y2038 safe semtimedop() system call, I chose to only
support the separate entry points, but that requires first supporting
the regular ones with their own syscall numbers.
The IPC_64 is now implied by the new semctl/shmctl/msgctl system
calls even on the architectures that require passing it with the ipc()
multiplexer.
I'm not adding the new semtimedop() or semop() on 32-bit architectures,
those will get implemented using the new semtimedop_time64() version
that gets added along with the other time64 calls.
Three 64-bit architectures (powerpc, s390 and sparc) get semtimedop().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Most architectures have assigned a numbers for the seccomp syscall
even when they do not implement it.
m68k is an exception here, so for consistency lets add the number.
Unless CONFIG_SECCOMP is implemented, the system call just
returns -ENOSYS.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A multi-platform kernel binary has to decide at run-time how to dispatch
the arch_nvram_ops calls. Add a platform-independent arch_nvram_ops
struct for this, to replace the atari-specific one.
Enable CONFIG_HAVE_ARCH_NVRAM_OPS for Macs.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PMU-based m68k Macs pre-date PowerMac-style NVRAM. Use the appropriate
PMU commands. Also implement the missing XPRAM accessors for VIA-based
Macs.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is intended to improve code style and not affect code behaviour.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adopt the existing *_read_byte and *_write_byte naming convention.
Rename via_pram_readbyte and via_pram_writebyte to avoid confusion.
Adjust calling conventions of mac_pram_* functions to match the
struct nvram_ops methods.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atari RTC NVRAM uses a checksum so implement the remaining arch_nvram_ops
methods for the set_checksum and initialize ioctls. Enable
CONFIG_HAVE_ARCH_NVRAM_OPS.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By implementing an arch_nvram_ops struct, a platform can re-use the
drivers/char/nvram.c module without needing any arch-specific code
in that module. Atari does so here.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace nvram_* functions with static functions in nvram.h. These will
become wrappers for struct nvram_ops method calls.
This patch effectively disables existing NVRAM functionality so as to
allow the rest of the series to be bisected without build failures.
That functionality is gradually re-implemented in subsequent patches.
Replace the sole validate-checksum-and-read-byte sequence with a call to
nvram_read() which will gain the same semantics in subsequent patches.
Remove unused exports.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the m68k-specific code out of the driver to make the driver generic.
I've used 'SPDX-License-Identifier: GPL-2.0+' for the new file because the
old file is covered by MODULE_LICENSE("GPL").
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a build failure when using GCC 8.1:
/usr/bin/ld: block/partitions/ldm.o: in function `ldm_parse_tocblock':
block/partitions/ldm.c:153: undefined reference to `strcmp'
This is caused by a new optimization which effectively replaces a
strncmp() call with a strcmp() call. This affects a number of strncmp()
call sites in the kernel.
The entire class of optimizations is avoided with -fno-builtin, which
gets enabled by -ffreestanding. This may avoid possible future build
failures in case new optimizations appear in future compilers.
I haven't done any performance measurements with this patch but I did
count the function calls in a defconfig build. For example, there are now
23 more sprintf() calls and 39 fewer strcpy() calls. The effect on the
other libc functions is smaller.
If this harms performance we can tackle that regression by optimizing
the call sites, ideally using semantic patches. That way, clang and ICC
builds might benfit too.
Cc: stable@vger.kernel.org
Reference: https://marc.info/?l=linux-m68k&m=154514816222244&w=2
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This comment has been wrong since before git.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Actual changes:
-CONFIG_IOSCHED_DEADLINE=m
-CONFIG_BATMAN_ADV_MCAST=y
-# CONFIG_SCSI_MQ_DEFAULT is not set
+CONFIG_CRYPTO_ADIANTUM=m
+CONFIG_CRYPTO_STREEBOG=m
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
With gcc 7.3.0:
arch/m68k/atari/config.c: In function ‘atari_switches_setup’:
arch/m68k/atari/config.c:151:2: warning: ISO C90 forbids variable length array ‘switches’ [-Wvla]
char switches[strlen(str) + 1];
^~~~
Replace the variable size by the maximum kernel command line size (256
bytes), which is an upper limit for all suboptions.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
With gcc 7.3.0:
arch/m68k/kernel/signal.c: In function ‘mangle_kernel_stack’:
arch/m68k/kernel/signal.c:654:3: warning: ISO C90 forbids variable length array ‘buf’ [-Wvla]
unsigned long buf[fsize / 2]; /* yes, twice as much */
^~~~~~~~
Replace the variable size by the upper limit, which is 168 bytes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The comment says that calling the ROM routine doesn't work. But testing
shows that the 68030 fall-back reset method does work, so just use that.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
According to The Guide To Mac Family Hardware, this is the correct way
to disable the VBL interrupt. The confusing comment here doesn't add any
value so remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Those Mac models which don't connect their RTC to VIA1 port B probably
have something else connected to those pins. Just leave them the way we
found them. Make the port B setup conditional on via_type, to match the
RTC accessors in arch/m68k/mac/misc.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Enabling NET_VENDOR_* Kconfig options does not directly affect the
kernel, so there is no need to explicitly disable them.
The individual network drivers under them are still disabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
For some reasons, I accidentally got rid of "generic-y += shmparam.h"
from some architectures.
Restore them to fix building c6x, h8300, hexagon, m68k, microblaze,
openrisc, and unicore32.
Fixes: d6e4b3e326 ("arch: remove redundant UAPI generic-y defines")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When testing in userspace, UBSAN pointed out that shifting into the sign
bit is undefined behaviour. It doesn't really make sense to ask for the
highest set bit of a negative value, so just turn the argument type into
an unsigned int.
Some architectures (eg ppc) already had it declared as an unsigned int,
so I don't expect too many problems.
Link: http://lkml.kernel.org/r/20181105221117.31828-1-willy@infradead.org
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Drivers:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding
-----BEGIN PGP SIGNATURE-----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=5He5
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries
by Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right Kconfig
files. This series instead just selects the presence (when needed) and
then handles everything in the bus-specific Kconfig file under drivers/.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WxId
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig file consolidation from Masahiro Yamada:
"Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries by
Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right
Kconfig files. This series instead just selects the presence (when
needed) and then handles everything in the bus-specific Kconfig file
under drivers/"
* tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
pcmcia: remove per-arch PCMCIA config entry
eisa: consolidate EISA Kconfig entry in drivers/eisa
rapidio: consolidate RAPIDIO config entry in drivers/rapidio
pcmcia: allow PCMCIA support independent of the architecture
PCI: consolidate the PCI_SYSCALL symbol
PCI: consolidate the PCI_DOMAINS and PCI_DOMAINS_GENERIC config options
PCI: consolidate PCI config entry in drivers/pci
MIPS: remove the HT_PCI config option
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for architectures
that have devices that perform DMA that is not cache coherent. Based
on the existing arm64 implementation and also used for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel data
leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script.
-----BEGIN PGP SIGNATURE-----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=in72
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
"A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for
architectures that have devices that perform DMA that is not cache
coherent. Based on the existing arm64 implementation and also used
for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel
data leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script"
* tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping: (73 commits)
dma-mapping: fix inverted logic in dma_supported
dma-mapping: deprecate dma_zalloc_coherent
dma-mapping: zero memory returned from dma_alloc_*
sparc/iommu: fix ->map_sg return value
sparc/io-unit: fix ->map_sg return value
arm64: default to the direct mapping in get_arch_dma_ops
PCI: Remove unused attr variable in pci_dma_configure
ia64: only select ARCH_HAS_DMA_COHERENT_TO_PFN if swiotlb is enabled
dma-mapping: bypass indirect calls for dma-direct
vmd: use the proper dma_* APIs instead of direct methods calls
dma-direct: merge swiotlb_dma_ops into the dma_direct code
dma-direct: use dma_direct_map_page to implement dma_direct_map_sg
dma-direct: improve addressability error reporting
swiotlb: remove dma_mark_clean
swiotlb: remove SWIOTLB_MAP_ERROR
ACPI / scan: Refactor _CCA enforcement
dma-mapping: factor out dummy DMA ops
dma-mapping: always build the direct mapping code
dma-mapping: move dma_cache_sync out of line
dma-mapping: move various slow path functions out of line
...
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
If we want to map memory from the DMA allocator to userspace it must be
zeroed at allocation time to prevent stale data leaks. We already do
this on most common architectures, but some architectures don't do this
yet, fix them up, either by passing GFP_ZERO when we use the normal page
allocator or doing a manual memset otherwise.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Sam Ravnborg <sam@ravnborg.org> [sparc]
When running the kernel in Fast RAM on Atari:
Ignoring memory chunk at 0x0:0xe00000 before the first chunk
...
Unable to handle kernel NULL pointer dereference at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<0069dbac>] free_all_bootmem+0x12c/0x186
SR: 2714 SP: (ptrval) a2: 005e3314
d0: 00000000 d1: 0000000a d2: 00000e00 d3: 00000000
d4: 005e1fc0 d5: 0000001a a0: 01000000 a1: 00000000
Process swapper (pid: 0, task=(ptrval))
Frame format=7 eff addr=00000736 ssw=0505 faddr=00000736
wb 1 stat/addr/data: 0000 00000000 00000000
wb 2 stat/addr/data: 0000 00000000 00000000
wb 3 stat/addr/data: 0000 00000736 00000000
push data: 00000000 00000000 00000000 00000000
Stack from 005e1f84:
00000000 0000000a 027d3260 006b5006 00000000 00000000 00000000 00000000
0004f062 0003a220 0069e272 005e1ff8 0000054c 00000000 00e00000 00000000
00000001 00693cd8 027d3260 0004f062 0003a220 00691be6 00000000 00000000
00000000 00000000 00000000 00000000 006b5006 00000000 00690872
Call Trace: [<0004f062>] printk+0x0/0x18
[<0003a220>] parse_args+0x0/0x2d4
[<0069e272>] memblock_virt_alloc_try_nid+0x0/0xa4
[<00693cd8>] mem_init+0xa/0x5c
[<0004f062>] printk+0x0/0x18
[<0003a220>] parse_args+0x0/0x2d4
[<00691be6>] start_kernel+0x1ca/0x462
[<00690872>] _sinittext+0x872/0x11f8
Code: 7a1a eaae 2270 6db0 0061 ef14 2f01 2f03 <96a9> 0736 2203 e589 d681 e78b d6a9 0732 2f03 2f40 0034 4eb9 0069 b8d0 260e 4fef
Disabling lock debugging due to kernel taint
Kernel panic - not syncing: Attempted to kill the idle task!
As the kernel must run in the memory chunk with the lowest address,
ST-RAM is ignored, and removed from the m68k_memory[] array.
However, it is not removed from memblock, causing a crash later.
More investigation shows that there are 3 places where memory chunks are
ignored, all after the calls to memblock_add() in m68k_parse_bootinfo(),
and thus causing crashes:
1. On classic m68k CPUs with a MMU, paging_init() ignores all memory
chunks below the first chunk, cfr. above,
2. On Amigas equipped with a Zorro III bus, config_amiga() ignores all
Zorro II memory,
3. If CONFIG_SINGLE_MEMORY_CHUNK=y, m68k_parse_bootinfo() ignores all
but the first memory chunk.
Fix this by moving the calls to memblock_add() from
m68k_parse_bootinfo() to paging_init(), after all ignored memory chunks
have been removed from m68k_memory[].
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Fixes: 1008a11590 ("m68k: switch to MEMBLOCK + NO_BOOTMEM")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
All architectures except for sparc64 use the dma-direct code in some
form, and even for sparc64 we had the discussion of a direct mapping
mode a while ago. In preparation for directly calling the direct
mapping code don't bother having it optionally but always build the
code in. This is a minor hardship for some powerpc and arm configs
that don't pull it in yet (although they should in a relase ot two),
and sparc64 which currently doesn't need it at all, but it will
reduce the ifdef mess we'd otherwise need significantly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k <linux-m68k@lists.linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
System call table generation script must be run to gener-
ate unistd_32.h and syscall_table.h files. This patch will
have changes which will invokes the script.
This patch will generate unistd_32.h and syscall_table.h
files by the syscall table generation script invoked by
m68k/Makefile and the generated files against the removed
files must be identical.
The generated uapi header file will be included in uapi/-
asm/unistd.h and generated system call table header file
will be included by kernel/syscalltable.S file.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The system call tables are in different format in all
architecture and it will be difficult to manually add,
modify or delete the syscall table entries in the res-
pective files. To make it easy by keeping a script and
which will generate the uapi header and syscall table
file. This change will also help to unify the implemen-
tation across all architectures.
The system call table generation script is added in
kernel/syscalls directory which contain the scripts to
generate both uapi header file and system call table
files. The syscall.tbl will be input for the scripts.
syscall.tbl contains the list of available system calls
along with system call number and corresponding entry
point. Add a new system call in this architecture will
be possible by adding new entry in the syscall.tbl file.
Adding a new table entry consisting of:
- System call number.
- ABI.
- System call name.
- Entry point name.
syscallhdr.sh and syscalltbl.sh will generate uapi header
unistd_32.h and syscall_table.h files respectively. Both
.sh files will parse the content syscall.tbl to generate
the header and table files. unistd_32.h will be included
by uapi/asm/unistd.h and syscall_table.h is included by
kernel/syscall_table.S - the real system call table.
ARM, s390 and x86 architecuture does have similar support.
I leverage their implementation to come up with a generic
solution.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
NR_syscalls macro holds the number of system call
exist in m68k architecture. We have to change the
value of NR_syscalls, if we add or delete a system
call.
One of the patch in this patch series has a script
which will generate a uapi header based on syscall-
.tbl file. The syscall.tbl file contains the total
number of system calls information. So we have two
option to update NR_syscalls value.
1. Update NR_syscalls in asm/unistd.h manually by
counting the no.of system calls. No need to up-
date NR_syscalls until we either add a new sys-
tem call or delete existing system call.
2. We can keep this feature it above mentioned sc-
ript, that will count the number of syscalls and
keep it in a generated file. In this case we
don't need to explicitly update NR_syscalls in
asm/unistd.h file.
The 2nd option will be the recommended one. For that,
I added the __NR_syscalls macro in uapi/asm/unistd.h
along with NR_syscalls asm/unistd.h. The macro __NR-
_syscalls also added for making the name convention
same across all architecture. While __NR_syscalls
isn't strictly part of the uapi, having it as part
of the generated header to simplifies the implement-
ation. We also need to enclose this macro with #ifdef
__KERNEL__ to avoid side effects.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Unroll the raw_outsb() loop using the optimized assembler code from
raw_outsw(). That code is copied and pasted, with movew changed to moveb.
This improves the performance of sequential write transfers using mac_esp
in PIO mode by 5% or 10%. (The DMA controller on the 840av/660av models is
still unsupported so PIO transfers are used.)
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is nothing architecture specific in the PCMCIA core, so allow
building it everywhere. The actual host controllers will depend on ISA,
PCI or a specific SOC.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- A fix for the pgtable_bytes misaccounting on s390. The patch changes
common code part in regard to page table folding and adds extra
checks to mm_[inc|dec]_nr_[pmds|puds].
- Add FORCE for all build targets using if_changed
- Use non-loadable phdr for the .vmlinux.info section to avoid
a segment overlap that confuses kexec
- Cleanup the attribute definition for the diagnostic sampling
- Increase stack size for CONFIG_KASAN=y builds
- Export __node_distance to fix a build error
- Correct return code of a PMU event init function
- An update for the default configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJb5TIMAAoJEDjwexyKj9rgIH8H/0daZTyxcLwY9gbigaq1Qs4R
/ScmAJJc2U/Qj8b9UskhsmHAUuAufF2oljU16SquP7CBGhtkLRrjPtdh1AMiiZGM
reVF7X5LU8MH0QUoNnKPWAL4DD1q2E99IAEH5TeGIODUG6srqvIHBNtXDWNLPtBf
fpOhJ/NssgxyuYUXi/WnoEjIyP8KABeG6SlpcLzYbmY1hUOIXcixuv39UrL0G5OO
P8ciL+W5rTcPZCnpJ1Xk9hKploT8gWXhMT5QhNnakgMF/25v80+TZy5xRZMuLAmQ
T5SFP6B71o05nLK7fLi3VAIKPv/QibjiyJOEf9uUHdo1XZcD5uRu0EQ/LklLUBU=
=4H06
-----END PGP SIGNATURE-----
Merge tag 's390-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- A fix for the pgtable_bytes misaccounting on s390. The patch changes
common code part in regard to page table folding and adds extra
checks to mm_[inc|dec]_nr_[pmds|puds].
- Add FORCE for all build targets using if_changed
- Use non-loadable phdr for the .vmlinux.info section to avoid a
segment overlap that confuses kexec
- Cleanup the attribute definition for the diagnostic sampling
- Increase stack size for CONFIG_KASAN=y builds
- Export __node_distance to fix a build error
- Correct return code of a PMU event init function
- An update for the default configs
* tag 's390-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/perf: Change CPUM_CF return code in event init function
s390: update defconfigs
s390/mm: Fix ERROR: "__node_distance" undefined!
s390/kasan: increase instrumented stack size to 64k
s390/cpum_sf: Rework attribute definition for diagnostic sampling
s390/mm: fix mis-accounting of pgtable_bytes
mm: add mm_pxd_folded checks to pgtable_bytes accounting functions
mm: introduce mm_[p4d|pud|pmd]_folded
mm: make the __PAGETABLE_PxD_FOLDED defines non-empty
s390: avoid vmlinux segments overlap
s390/vdso: add missing FORCE to build targets
s390/decompressor: add missing FORCE to build targets
Change the currently empty defines for __PAGETABLE_PMD_FOLDED,
__PAGETABLE_PUD_FOLDED and __PAGETABLE_P4D_FOLDED to return 1.
This makes it possible to use __is_defined() to test if the
preprocessor define exists.
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem(size) is a shortcut for allocation of SMP_CACHE_BYTES
aligned memory. When the align parameter of memblock_alloc() is 0, the
alignment is implicitly set to SMP_CACHE_BYTES and thus alloc_bootmem(size)
and memblock_alloc(size, 0) are equivalent.
The conversion is done using the following semantic patch:
@@
expression size;
@@
- alloc_bootmem(size)
+ memblock_alloc(size, 0)
Link: http://lkml.kernel.org/r/1536927045-23536-22-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem_pages() function allocates PAGE_SIZE aligned memory.
memblock_alloc() with alignment set to PAGE_SIZE does exactly the same
thing.
The conversion is done using the following semantic patch:
@@
expression e;
@@
- alloc_bootmem_pages(e)
+ memblock_alloc(e, PAGE_SIZE)
Link: http://lkml.kernel.org/r/1536927045-23536-20-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem_low_pages() function allocates PAGE_SIZE aligned regions
from low memory. memblock_alloc_low() with alignment set to PAGE_SIZE does
exactly the same thing.
The conversion is done using the following semantic patch:
@@
expression e;
@@
- alloc_bootmem_low_pages(e)
+ memblock_alloc_low(e, PAGE_SIZE)
Link: http://lkml.kernel.org/r/1536927045-23536-19-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architecures use memblock for early memory management. There is no need
for the CONFIG_HAVE_MEMBLOCK configuration option.
[rppt@linux.vnet.ibm.com: of/fdt: fixup #ifdefs]
Link: http://lkml.kernel.org/r/20180919103457.GA20545@rapoport-lnx
[rppt@linux.vnet.ibm.com: csky: fixups after bootmem removal]
Link: http://lkml.kernel.org/r/20180926112744.GC4628@rapoport-lnx
[rppt@linux.vnet.ibm.com: remove stale #else and the code it protects]
Link: http://lkml.kernel.org/r/1538067825-24835-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1536927045-23536-4-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All achitectures select NO_BOOTMEM which essentially becomes 'Y' for any
kernel configuration and therefore it can be removed.
[alexander.h.duyck@linux.intel.com: remove now defunct NO_BOOTMEM from depends list for deferred init]
Link: http://lkml.kernel.org/r/20180925201814.3576.15105.stgit@localhost.localdomain
Link: http://lkml.kernel.org/r/1536927045-23536-3-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prefer _THIS_IP_ defined in linux/kernel.h.
Most definitions of current_text_addr were the same as _THIS_IP_, but
a few archs had inline assembly instead.
This patch removes the final call site of current_text_addr, making all
of the definitions dead code.
[akpm@linux-foundation.org: fix arch/csky/include/asm/processor.h]
Link: http://lkml.kernel.org/r/20180911182413.180715-1-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68k nommu fix from Greg Ungerer:
"Only a single change to fix an out of bounds array access when parsing
boot command line"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: fix command-line parsing when passed from u-boot
- Just two small cleanups.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW9WEMhUcZ2VlcnRAbGlu
dXgtbTY4ay5vcmcACgkQisJQ/WRJ8XCbswD+NNpRY9sDL686TicLAB8nnIIi7wzA
eCgPpsXprxrRjEsA/3Wpsgnu32y6zDqh3UCFdPBnYUTj3ev1oxGdmzI3gJMG
=y1Lq
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.20-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Just two small cleanups"
* tag 'm68k-for-v4.20-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/sun3: Remove is_medusa and m68k_pgtable_cachemode
m68k/atari: ARAnyM - Remove reference to long-deprecated MODULE_PARM
Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of fairly
complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for each
process and preload them on context switch. Leading to a 27% speedup for our
context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print more debug
information when they occur, and try to continue running by flushing the SLB
and reloading, rather than treating them as fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on 64-bit
Book3S. We only support up to 512TB as regular system memory, otherwise the
percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are presented
to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE flags.
- Add a driver for the PAPR SCM (storage class memory) interface, allowing
guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we need to use
a trampoline to get to ftrace_caller().
Many other smaller enhancements and cleanups.
Thanks to:
Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton Blanchard, Aravinda
Prasad, Bartlomiej Zolnierkiewicz, Benjamin Herrenschmidt, Breno Leitao,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Dan Carpenter, Daniel
Axtens, Finn Thain, Gautham R. Shenoy, Gustavo Romero, Haren Myneni, Hari
Bathini, Jia Hongtao, Joel Stanley, John Allen, Laurent Dufour, Madhavan
Srinivasan, Mahesh Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael
Bringmann, Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran,
Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab, Rob Herring, Sam
Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan Johnson, Stephen Rothwell,
Stewart Smith, Suraj Jitindar Singh, Tyrel Datwyler, Vaibhav Jain, Vasant
Hegde, YueHaibing, zhong jiang,
-----BEGIN PGP SIGNATURE-----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=I0pj
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of
fairly complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for
each process and preload them on context switch. Leading to a 27%
speedup for our context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print
more debug information when they occur, and try to continue running
by flushing the SLB and reloading, rather than treating them as
fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on
64-bit Book3S. We only support up to 512TB as regular system
memory, otherwise the percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task
canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are
presented to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE
flags.
- Add a driver for the PAPR SCM (storage class memory) interface,
allowing guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we
need to use a trampoline to get to ftrace_caller().
And many other smaller enhancements and cleanups.
Thanks to: Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton
Blanchard, Aravinda Prasad, Bartlomiej Zolnierkiewicz, Benjamin
Herrenschmidt, Breno Leitao, Cédric Le Goater, Christophe Leroy,
Christophe Lombard, Dan Carpenter, Daniel Axtens, Finn Thain, Gautham
R. Shenoy, Gustavo Romero, Haren Myneni, Hari Bathini, Jia Hongtao,
Joel Stanley, John Allen, Laurent Dufour, Madhavan Srinivasan, Mahesh
Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael Bringmann,
Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver
O'Halloran, Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab,
Rob Herring, Sam Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan
Johnson, Stephen Rothwell, Stewart Smith, Suraj Jitindar Singh, Tyrel
Datwyler, Vaibhav Jain, Vasant Hegde, YueHaibing, zhong jiang"
* tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (221 commits)
Revert "selftests/powerpc: Fix out-of-tree build errors"
powerpc/msi: Fix compile error on mpc83xx
powerpc: Fix stack protector crashes on CPU hotplug
powerpc/traps: restore recoverability of machine_check interrupts
powerpc/64/module: REL32 relocation range check
powerpc/64s/radix: Fix radix__flush_tlb_collapsed_pmd double flushing pmd
selftests/powerpc: Add a test of wild bctr
powerpc/mm: Fix page table dump to work on Radix
powerpc/mm/radix: Display if mappings are exec or not
powerpc/mm/radix: Simplify split mapping logic
powerpc/mm/radix: Remove the retry in the split mapping logic
powerpc/mm/radix: Fix small page at boundary when splitting
powerpc/mm/radix: Fix overuse of small pages in splitting logic
powerpc/mm/radix: Fix off-by-one in split mapping logic
powerpc/ftrace: Handle large kernel configs
powerpc/mm: Fix WARN_ON with THP NUMA migration
selftests/powerpc: Fix out-of-tree build errors
powerpc/time: no steal_time when CONFIG_PPC_SPLPAR is not selected
powerpc/time: Only set CONFIG_ARCH_HAS_SCALED_CPUTIME on PPC64
powerpc/time: isolate scaled cputime accounting in dedicated functions.
...
Pull timekeeping updates from Thomas Gleixner:
"The timers and timekeeping departement provides:
- Another large y2038 update with further preparations for providing
the y2038 safe timespecs closer to the syscalls.
- An overhaul of the SHCMT clocksource driver
- SPDX license identifier updates
- Small cleanups and fixes all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
tick/sched : Remove redundant cpu_online() check
clocksource/drivers/dw_apb: Add reset control
clocksource: Remove obsolete CLOCKSOURCE_OF_DECLARE
clocksource/drivers: Unify the names to timer-* format
clocksource/drivers/sh_cmt: Add R-Car gen3 support
dt-bindings: timer: renesas: cmt: document R-Car gen3 support
clocksource/drivers/sh_cmt: Properly line-wrap sh_cmt_of_table[] initializer
clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines
clocksource/drivers/sh_cmt: Fixup for 64-bit machines
clocksource/drivers/sh_tmu: Convert to SPDX identifiers
clocksource/drivers/sh_mtu2: Convert to SPDX identifiers
clocksource/drivers/sh_cmt: Convert to SPDX identifiers
clocksource/drivers/renesas-ostm: Convert to SPDX identifiers
clocksource: Convert to using %pOFn instead of device_node.name
tick/broadcast: Remove redundant check
RISC-V: Request newstat syscalls
y2038: signal: Change rt_sigtimedwait to use __kernel_timespec
y2038: socket: Change recvmmsg to use __kernel_timespec
y2038: sched: Change sched_rr_get_interval to use __kernel_timespec
y2038: utimes: Rework #ifdef guards for compat syscalls
...
- mostly more consolidation of the direct mapping code, including
converting over hexagon, and merging the coherent and non-coherent
code into a single dma_map_ops instance (me)
- cleanups for the dma_configure/dma_unconfigure callchains (me)
- better handling of dma_masks in odd setups (me, Alexander Duyck)
- better debugging of passing vmalloc address to the DMA API
(Stephen Boyd)
- CMA command line parsing fix (He Zhe)
-----BEGIN PGP SIGNATURE-----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=AVSD
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.20' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"First batch of dma-mapping changes for 4.20.
There will be a second PR as some big changes were only applied just
before the end of the merge window, and I want to give them a few more
days in linux-next.
Summary:
- mostly more consolidation of the direct mapping code, including
converting over hexagon, and merging the coherent and non-coherent
code into a single dma_map_ops instance (me)
- cleanups for the dma_configure/dma_unconfigure callchains (me)
- better handling of dma_masks in odd setups (me, Alexander Duyck)
- better debugging of passing vmalloc address to the DMA API (Stephen
Boyd)
- CMA command line parsing fix (He Zhe)"
* tag 'dma-mapping-4.20' of git://git.infradead.org/users/hch/dma-mapping: (27 commits)
dma-direct: respect DMA_ATTR_NO_WARN
dma-mapping: translate __GFP_NOFAIL to DMA_ATTR_NO_WARN
dma-direct: document the zone selection logic
dma-debug: Check for drivers mapping invalid addresses in dma_map_single()
dma-direct: fix return value of dma_direct_supported
dma-mapping: move dma_default_get_required_mask under ifdef
dma-direct: always allow dma mask <= physiscal memory size
dma-direct: implement complete bus_dma_mask handling
dma-direct: refine dma_direct_alloc zone selection
dma-direct: add an explicit dma_direct_get_required_mask
dma-mapping: make the get_required_mask method available unconditionally
unicore32: remove swiotlb support
Revert "dma-mapping: clear dev->dma_ops in arch_teardown_dma_ops"
dma-mapping: support non-coherent devices in dma_common_get_sgtable
dma-mapping: consolidate the dma mmap implementations
dma-mapping: merge direct and noncoherent ops
dma-mapping: move the dma_coherent flag to struct device
MIPS: don't select DMA_MAYBE_COHERENT from DMA_PERDEV_COHERENT
dma-mapping: add the missing ARCH_HAS_SYNC_DMA_FOR_CPU_ALL declaration
dma-mapping: fix panic caused by passing empty cma command line argument
...
atafd.h and atafdreg.h are only used from ataflop.c, so merge them in
there.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes command_line array zero-terminated
one byte over the end of the array, causing boot to hang.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Now that the 68k Mac port has adopted the via-pmu driver, the same RTC
code can be shared between m68k and powerpc. Replace duplicated code in
arch/powerpc and arch/m68k with common RTC accessors for Cuda and PMU.
Drop the problematic WARN_ON which was introduced in commit 22db552b50
("powerpc/powermac: Fix rtc read/write functions").
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into for-4.20/block
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only use it in biovec_phys_mergeable and a m68k paravirt driver,
so just opencode it there. Also remove the pointless unsigned long cast
for the offset in the opencoded instances.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All the cache maintainance is already stubbed out when not enabled,
but merging the two allows us to nicely handle the case where
cache maintainance is required for some devices, but not others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
As it turns out, the AVX2 multibuffer SHA routines are currently
broken [0], in a way that would have likely been noticed if this
code were in wide use. Since the code is too complicated to be
maintained by anyone except the original authors, and since the
performance benefits for real-world use cases are debatable to
begin with, it is better to drop it entirely for the moment.
[0] https://marc.info/?l=linux-crypto-vger&m=153476243825350&w=2
Suggested-by: Eric Biggers <ebiggers@google.com>
Cc: Megha Dey <megha.dey@linux.intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These are unused, undesired, and have never actually been used by
anybody. The original authors of this code have changed their mind about
its inclusion. While originally proposed for disk encryption on low-end
devices, the idea was discarded [1] in favor of something else before
that could really get going. Therefore, this patch removes Speck.
[1] https://marc.info/?l=linux-crypto-vger&m=153359499015659
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The bootmem to memblock conversion introduced by the commit 1008a11590
("m68k: switch to MEMBLOCK + NO_BOOTMEM") made reservation of kernel code
and data to start from a wrong address.
Fix it.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Now that the 68k Mac port has adopted the via-pmu driver, it must decode
the PMU response accordingly otherwise the date and time will be wrong.
Fixes: ebd722275f ("macintosh/via-pmu: Replace via-pmu68k driver with via-pmu driver")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Given that MODULE_PARM was deprecated years ago, and this is only a
comment, get rid of this reference to further the goal of deleting
every remaining reference in the entire kernel code base.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The sys_llseek sytem call is needed on all 32-bit architectures and
none of the 64-bit ones, so we can remove the __ARCH_WANT_SYS_LLSEEK guard
and simplify the include/asm-generic/unistd.h header further.
Since 32-bit tasks can run either natively or in compat mode on 64-bit
architectures, we have to check for both !CONFIG_64BIT and CONFIG_COMPAT.
There are a few 64-bit architectures that also reference sys_llseek
in their 64-bit ABI (e.g. sparc), but I verified that those all
select CONFIG_COMPAT, so the #if check is still correct here. It's
a bit odd to include it in the syscall table though, as it's the
same as sys_lseek() on 64-bit, but with strange calling conventions.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have four generations of stat() syscalls:
- the oldstat syscalls that are only used on the older architectures
- the newstat family that is used on all 64-bit architectures but
lacked support for large files on 32-bit architectures.
- the stat64 family that is used mostly on 32-bit architectures to
replace newstat
- statx() to replace all of the above, adding 64-bit timestamps among
other things.
We already compile stat64 only on those architectures that need it,
but newstat is always built, including on those that don't reference
it. This adds a new __ARCH_WANT_NEW_STAT symbol along the lines of
__ARCH_WANT_OLD_STAT and __ARCH_WANT_STAT64 to control compilation of
newstat. All architectures that need it use an explict define, the
others now get a little bit smaller, and future architecture (including
64-bit targets) won't ever see it.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Pull m68knommu updates from Greg Ungerer:
"Only two changes.
One cleans up warnings in the ColdFire DMA code, the other stubs out
(with warnings) ColdFire clock api functions not normally used"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Fix typos in Coldfire 5272 DMA debug code
m68k: coldfire: Normalize clk API
Merge updates from Andrew Morton:
- a few misc things
- a few Y2038 fixes
- ntfs fixes
- arch/sh tweaks
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
mm/hmm.c: remove unused variables align_start and align_end
fs/userfaultfd.c: remove redundant pointer uwq
mm, vmacache: hash addresses based on pmd
mm/list_lru: introduce list_lru_shrink_walk_irq()
mm/list_lru.c: pass struct list_lru_node* as an argument to __list_lru_walk_one()
mm/list_lru.c: move locking from __list_lru_walk_one() to its caller
mm/list_lru.c: use list_lru_walk_one() in list_lru_walk_node()
mm, swap: make CONFIG_THP_SWAP depend on CONFIG_SWAP
mm/sparse: delete old sparse_init and enable new one
mm/sparse: add new sparse_init_nid() and sparse_init()
mm/sparse: move buffer init/fini to the common place
mm/sparse: use the new sparse buffer functions in non-vmemmap
mm/sparse: abstract sparse buffer allocations
mm/hugetlb.c: don't zero 1GiB bootmem pages
mm, page_alloc: double zone's batchsize
mm/oom_kill.c: document oom_lock
mm/hugetlb: remove gigantic page support for HIGHMEM
mm, oom: remove sleep from under oom_lock
kernel/dma: remove unsupported gfp_mask parameter from dma_alloc_from_contiguous()
mm/cma: remove unsupported gfp_mask parameter from cma_alloc()
...
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")
In this patch all the caller of handle_mm_fault() are changed to return
vm_fault_t type.
Link: http://lkml.kernel.org/r/20180617084810.GA6730@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Levin, Alexander (Sasha Levin)" <alexander.levin@verizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAlt2O6cTHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgC7hD/4+cj796Df7GsVsIMxzQm7SS9dklIdO
JuKj2Nr5HRzTH59jWlXukLG9mfTNCFgFJB4gEpK1ArDOTcHTCI9RRsLZTZ/kum66
7Pd+7T40dLYXB5uecuUs0vMXa2fI3syKh1VLzACSXv3Dh9BBIKQBwW/aD2eww4YI
1fS5LnXZ2PSxfr6KNAC6ogZnuaiD0sHXOYrtGHq+S/TFC7+Z6ySa6+AnPS+hPVoo
/rHDE1Khr66aj7uk+PP2IgUrCFj6Sbj6hTVlS/iAuwbMjUl9ty6712PmvX9x6wMZ
13hJQI+g6Ci+lqLKqmqVUpXGSr6y4NJGPS/Hko4IivBTJApI+qV/tF2H9nxU+6X0
0RqzsMHPHy13n2torA1gC7ttzOuXPI4hTvm6JWMSsfmfjTxLANJng3Dq3ejh6Bqw
76EMowpDLexwpy7/glPpqNdsP4ySf2Qm8yq3mR7qpL4m3zJVRGs11x+s5DW8NKBL
Fl5SqZvd01abH+sHwv6NLaLkEtayUyohxvyqu2RU3zu5M5vi7DhqstybTPjKPGu0
icSPh7b2y10WpOUpC6lxpdi8Me8qH47mVc/trZ+SpgBrsuEmtJhGKszEnzRCOqos
o2IhYHQv3lQv86kpaAFQlg/RO+Lv+Lo5qbJ209V+hfU5nYzXpEulZs4dx1fbA+ze
fK8GEh+u0L4uJg==
=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
Move the source statements of arch-independent Kconfig files instead of
duplicating the includes in every arch/$(SRCARCH)/Kconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gsQJ
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig consolidation from Masahiro Yamada:
"Consolidation of Kconfig files by Christoph Hellwig.
Move the source statements of arch-independent Kconfig files instead
of duplicating the includes in every arch/$(SRCARCH)/Kconfig"
* tag 'kconfig-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: add a Memory Management options" menu
kconfig: move the "Executable file formats" menu to fs/Kconfig.binfmt
kconfig: use a menu in arch/Kconfig to reduce clutter
kconfig: include kernel/Kconfig.preempt from init/Kconfig
Kconfig: consolidate the "Kernel hacking" menu
kconfig: include common Kconfig files from top-level Kconfig
kconfig: remove duplicate SWAP symbol defintions
um: create a proper drivers Kconfig
um: cleanup Kconfig files
um: stop abusing KBUILD_KCONFIG
Pull locking/atomics update from Thomas Gleixner:
"The locking, atomics and memory model brains delivered:
- A larger update to the atomics code which reworks the ordering
barriers, consolidates the atomic primitives, provides the new
atomic64_fetch_add_unless() primitive and cleans up the include
hell.
- Simplify cmpxchg() instrumentation and add instrumentation for
xchg() and cmpxchg_double().
- Updates to the memory model and documentation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
locking/atomics: Rework ordering barriers
locking/atomics: Instrument cmpxchg_double*()
locking/atomics: Instrument xchg()
locking/atomics: Simplify cmpxchg() instrumentation
locking/atomics/x86: Reduce arch_cmpxchg64*() instrumentation
tools/memory-model: Rename litmus tests to comply to norm7
tools/memory-model/Documentation: Fix typo, smb->smp
sched/Documentation: Update wake_up() & co. memory-barrier guarantees
locking/spinlock, sched/core: Clarify requirements for smp_mb__after_spinlock()
sched/core: Use smp_mb() in wake_woken_function()
tools/memory-model: Add informal LKMM documentation to MAINTAINERS
locking/atomics/Documentation: Describe atomic_set() as a write operation
tools/memory-model: Make scripts executable
tools/memory-model: Remove ACCESS_ONCE() from model
tools/memory-model: Remove ACCESS_ONCE() from recipes
locking/memory-barriers.txt/kokr: Update Korean translation to fix broken DMA vs. MMIO ordering example
MAINTAINERS: Add Daniel Lustig as an LKMM reviewer
tools/memory-model: Fix ISA2+pooncelock+pooncelock+pombonce name
tools/memory-model: Add litmus test for full multicopy atomicity
locking/refcount: Always allow checked forms
...
Almost all architectures include it. Add a ARCH_NO_PREEMPT symbol to
disable preempt support for alpha, hexagon, non-coldfire m68k and
user mode Linux.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the source of lib/Kconfig.debug and arch/$(ARCH)/Kconfig.debug to
the top-level Kconfig. For two architectures that means moving their
arch-specific symbols in that menu into a new arch Kconfig.debug file,
and for a few more creating a dummy file so that we can include it
unconditionally.
Also move the actual 'Kernel hacking' menu to lib/Kconfig.debug, where
it belongs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Instead of duplicating the source statements in every architecture just
do it once in the toplevel Kconfig file.
Note that with this the inclusion of arch/$(SRCARCH/Kconfig moves out of
the top-level Kconfig into arch/Kconfig so that don't violate ordering
constraits while keeping a sensible menu structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that the PowerMac via-pmu driver supports m68k PowerBooks,
switch over to that driver and remove the via-pmu68k driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Don't load the via-pmu68k driver on early PowerBooks. The M50753 PMU
device found in those models was never supported by this driver.
Attempting to load the driver usually causes a boot hang.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If DEBUG_DMA is defined:
include/asm/dma.h: In function ‘set_dma_mode’:
include/asm/dma.h:393: error: ‘dmabp’ undeclared (first use in this function)
include/asm/dma.h:393: error: (Each undeclared identifier is reported only once
include/asm/dma.h:393: error: for each function it appears in.)
include/asm/dma.h: In function ‘set_dma_addr’:
include/asm/dma.h:424: error: ‘dmawp’ undeclared (first use in this function)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Coldfire still provides its own variant of the clk API rather than using
the generic COMMON_CLK API. This generally works, but it causes some
link errors with drivers using the clk_round_rate(), clk_set_rate(),
clk_set_parent(), or clk_get_parent() functions when a platform lacks
those interfaces.
This adds empty stub implementations for each of them, and I don't even
try to do something useful here but instead just print a WARN() message
to make it obvious what is going on if they ever end up being called.
The drivers that call these won't be used on these platforms (otherwise
we'd get a link error today), so the added code is harmless bloat and
will warn about accidental use.
Based on commit bd7fefe1f0 ("ARM: w90x900: normalize clk API").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
In m68k the physical memory is described by [memory_start, memory_end] for
!MMU variant and by m68k_memory array of memory ranges for the MMU version.
This information is directly use to register the physical memory with
memblock.
The reserve_bootmem() calls are replaced with memblock_reserve() and the
bootmap bitmap allocation is simply dropped.
Since the MMU variant creates early mappings only for the small part of the
memory we force bottom-up allocations in memblock.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add explicit casting to unsigned long to the __va() parameter
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The generic bitops declare __ffs as
static inline unsigned long __ffs(unsigned long word);
Convert the m68k version to match the generic declaration.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The dummy functions defined in <asm/io_mm.h> can be provided by
<asm-generic/io.h>.
As nommu already uses <asm-generic/io.h>, move its inclusion to
<asm/io.h>, and add/adjust include guards where appropriate.
This gets rid of lots of "statement with no effect" and "unused
variable" warnings when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
The mem*io define guards are applicable to all users of <asm/kmap.h>.
Hence move them, and drop the #ifdef.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
- Add missing define guard for ioremap_wt(),
- Move ARCH_HAS_IOREMAP_WT from <asm/io_mm.h> to <asm/kmap.h>, as it
is applicable to Coldfire with MMU, too,
- Fix typo s/ioremap_fillcache/ioremap_fullcache/,
- Add define guard for iounmap() for consistency with other
architectures.
Fixes: 9746882f54 ("m68k: group io mapping definitions and functions")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Commit 397ac99c6c ("m68k: remove dead timer code") removed set_rtc_mmss()
because it was unused in 2012. However, this was itself the only user of the
mach_set_clock_mmss() callback and the many implementations of that callback,
which are equally unused.
This removes all of those as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The real-time clock on m68k (and powerpc) mac systems uses an unsigned
32-bit value starting in 1904, which overflows in 2040, about two years
later than everyone else, but this gets wrapped around in the Linux
code in 2038 already because of the deprecated usage of time_t and/or
long in the conversion.
Getting rid of the deprecated interfaces makes it work until 2040 as
documented, and it could be easily extended by reinterpreting
the resulting time64_t as a positive number. For the moment, I'm
adding a WARN_ON() that triggers if we encounter a time before 1970
or after 2040 (the two are indistinguishable).
This brings it in line with the corresponding code that we have on
powerpc macintosh.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[fthain: Adopt __u32 for the union in via_read_time(), consistent with
changes to via_write_time()]
[fthain: Use lower_32_bits() in via_write_time(), consistent with changes
to pmu_write_time() and cuda_write_time()]
[fthain: Have via_read_time() return a time64_t, consistent with changes
to pmu_read_time() and cuda_read_time()]
[fthain: Drop the pointless wraparound conditional in via_read_time()]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[geert: Drop WARN_ON(), as it is reported to trigger on powermac]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
I can confirm that mac_scsi PDMA now works on these machines.
This increases sequential read throughput by a factor of 4.5.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Booting a ColdFire m68k core with MMU enabled causes a "bad page state"
oops since commit 1d40a5ea01 ("mm: mark pages in use for page tables"):
BUG: Bad page state in process sh pfn:01ce2
page:004fefc8 count:0 mapcount:-1024 mapping:00000000 index:0x0
flags: 0x0()
raw: 00000000 00000000 00000000 fffffbff 00000000 00000100 00000200 00000000
raw: 039c4000
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 22 Comm: sh Not tainted 4.17.0-07461-g1d40a5ea01d5 #13
Fix by calling pgtable_page_dtor() in our __pte_free_tlb() code path,
so that the PG_table flag is cleared before we free the pte page.
Note that I had to change the type of pte_free() to be static from
extern. Otherwise you get a lot of warnings like this:
./arch/m68k/include/asm/mcf_pgalloc.h:80:2: warning: ‘pgtable_page_dtor’ is static but used in inline function ‘pte_free’ which is not static
pgtable_page_dtor(page);
^
And making it static is consistent with our use of this in the other
m68k pgalloc definitions of pte_free().
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
CC: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Many of the inc/dec ops are mandatory, but for most architectures inc/dec are
simply trivial wrappers around their corresponding add/sub ops.
Let's make all the inc/dec ops optional, so that we can get rid of these
boilerplate wrappers.
The instrumented atomics are updated accordingly.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/20180621121321.4761-17-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the atomics return the result of a test applied after the atomic
operation, and almost all architectures implement these as trivial
wrappers around the underlying atomic. Specifically:
* <atomic>_inc_and_test(v) is (<atomic>_inc_return(v) == 0)
* <atomic>_dec_and_test(v) is (<atomic>_dec_return(v) == 0)
* <atomic>_sub_and_test(i, v) is (<atomic>_sub_return(i, v) == 0)
* <atomic>_add_negative(i, v) is (<atomic>_add_return(i, v) < 0)
Rather than have these definitions duplicated in all architectures, with
minor inconsistencies in formatting and documentation, let's make these
operations optional, with default fallbacks as above. Implementations
must now provide a preprocessor symbol.
The instrumented atomics are updated accordingly.
Both x86 and m68k have custom implementations, which are left as-is,
given preprocessor symbols to avoid being overridden.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/20180621121321.4761-16-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Several architectures these have a near-identical implementation based
on atomic_read() and atomic_cmpxchg() which we can instead define in
<linux/atomic.h>, so let's do so, using something close to the existing
x86 implementation with try_cmpxchg().
Where an architecture provides its own atomic_fetch_add_unless(), it
must define a preprocessor symbol for it. The instrumented atomics are
updated accordingly.
Note that arch/arc's existing atomic_fetch_add_unless() had redundant
barriers, as these are already present in its atomic_cmpxchg()
implementation.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Link: https://lore.kernel.org/lkml/20180621121321.4761-7-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While __atomic_add_unless() was originally intended as a building-block
for atomic_add_unless(), it's now used in a number of places around the
kernel. It's the only common atomic operation named __atomic*(), rather
than atomic_*(), and for consistency it would be better named
atomic_fetch_add_unless().
This lack of consistency is slightly confusing, and gets in the way of
scripting atomics. Given that, let's clean things up and promote it to
an official part of the atomics API, in the form of
atomic_fetch_add_unless().
This patch converts definitions and invocations over to the new name,
including the instrumented version, using the following script:
----
git grep -w __atomic_add_unless | while read line; do
sed -i '{s/\<__atomic_add_unless\>/atomic_fetch_add_unless/}' "${line%%:*}";
done
git grep -w __arch_atomic_add_unless | while read line; do
sed -i '{s/\<__arch_atomic_add_unless\>/arch_atomic_fetch_add_unless/}' "${line%%:*}";
done
----
Note that we do not have atomic{64,_long}_fetch_add_unless(), which will
be introduced by later patches.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/20180621121321.4761-2-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
<asm-generic/bitops/lock.h> is shortly going to be built on top of the
atomic_long_*() API, which introduces a nasty circular dependency for
m68k where <linux/atomic.h> pulls in <linux/bitops.h> via:
linux/atomic.h
asm/atomic.h
linux/irqflags.h
asm/irqflags.h
linux/preempt.h
asm/preempt.h
asm-generic/preempt.h
linux/thread_info.h
asm/thread_info.h
asm/page.h
asm-generic/getorder.h
linux/log2.h
linux/bitops.h
Since m68k isn't SMP and doesn't support ACQUIRE/RELEASE barriers, we
can just define the lock bitops in terms of the atomic bitops in the
<asm/bitops.h> header.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: yamada.masahiro@socionext.com
Link: https://lore.kernel.org/lkml/1529412794-17720-3-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull m68knommu updates from Greg Ungerer:
"These changes all relate to converting the IO access functions for the
ColdFire (and all other non-MMU m68k) platforms to use asm-generic IO
instead.
This makes the IO support the same on all ColdFire (regardless of MMU
enabled or not) and means we can now support PCI in non-MMU mode.
As a bonus these changes remove more code than they add"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: fix ColdFire PCI config reads and writes
m68k: introduce iomem() macro for __iomem conversions
m68k: allow ColdFire PCI bus on MMU and non-MMU configuration
m68k: fix ioremapping for internal ColdFire peripherals
m68k: fix read/write multi-byte IO for PCI on ColdFire
m68k: don't redefine access functions if we have PCI
m68k: remove old ColdFire IO access support code
m68k: use io_no.h for MMU and non-MMU enabled ColdFire
m68k: setup PCI support code in io_no.h
m68k: group io mapping definitions and functions
m68k: rework raw access macros for the non-MMU case
m68k: use asm-generic/io.h for non-MMU io access functions
m68k: put definition guards around virt_to_phys and phys_to_virt
m68k: move *_relaxed macros into io_no.h and io_mm.h
Pull timers and timekeeping updates from Thomas Gleixner:
- Core infrastucture work for Y2038 to address the COMPAT interfaces:
+ Add a new Y2038 safe __kernel_timespec and use it in the core
code
+ Introduce config switches which allow to control the various
compat mechanisms
+ Use the new config switch in the posix timer code to control the
32bit compat syscall implementation.
- Prevent bogus selection of CPU local clocksources which causes an
endless reselection loop
- Remove the extra kthread in the clocksource code which has no value
and just adds another level of indirection
- The usual bunch of trivial updates, cleanups and fixlets all over the
place
- More SPDX conversions
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
clocksource/drivers/mxs_timer: Switch to SPDX identifier
clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Remove outdated file path
clocksource/drivers/arc_timer: Add comments about locking while read GFRC
clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
clocksource/drivers/sprd: Fix Kconfig dependency
clocksource: Move inline keyword to the beginning of function declarations
timer_list: Remove unused function pointer typedef
timers: Adjust a kernel-doc comment
tick: Prefer a lower rating device only if it's CPU local device
clocksource: Remove kthread
time: Change nanosleep to safe __kernel_* types
time: Change types to new y2038 safe __kernel_* types
time: Fix get_timespec64() for y2038 safe compat interfaces
time: Add new y2038 safe __kernel_timespec
posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_64BIT_TIME in architectures
compat: Enable compat_get/put_timespec64 always
...
- A few time-related fixes:
- off-by-one calendar month on some classes of machines,
- Y2038 preparation,
- Build fix for ndelay() being called with a 64-bit type,
- Revive 64-bit get_user(), which is used by some Android code,
- Defconfig updates,
- Fix for a long-standing fatal bug in iounmap() on '020/030, which
was actually fixed in 2.4.23, but never in 2.5.x and later,
- Default DMA mask to avoid warning splats,
- Minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iF4EABYIAAYFAlsU83oACgkQisJQ/WRJ8XC+tAD/TC++gQlSUbz5ZSjZ95aGZl1O
nHjOHQpnae/R9pNFjogA/imtboTg7ukyx9Qnv7q47G8w7wGyxS+QHVTa6Hr2tEEF
=8PWk
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.18-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- a few time-related fixes:
- off-by-one calendar month on some classes of machines
- Y2038 preparation
- build fix for ndelay() being called with a 64-bit type
- revive 64-bit get_user(), which is used by some Android code
- defconfig updates
- fix for a long-standing fatal bug in iounmap() on '020/030, which was
actually fixed in 2.4.23, but never in 2.5.x and later
- default DMA mask to avoid warning splats
- minor fixes and cleanups
* tag 'm68k-for-v4.18-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Set default dma mask for platform devices
m68k/mm: Adjust VM area to be unmapped by gap size for __iounmap()
m68k/defconfig: Update defconfigs for v4.17-rc3
m68k/uaccess: Revive 64-bit get_user()
m68k: Implement ndelay() as an inline function to force type checking/casting
zorro: Add a blank line after declarations
m68k: Use read_persistent_clock64() consistently
m68k: Fix off-by-one calendar month
m68k: Fix style, spelling, and grammar in siginfo_build_tests()
m68k/mac: Fix SWIM memory resource end address
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----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=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
This avoids a WARNING splat when loading the macsonic or macmace driver.
Please see commit 205e1b7f51 ("dma-mapping: warn when there is no
coherent_dma_mask").
This implementation of arch_setup_pdev_archdata() differs from the
powerpc one, in that this one avoids clobbering a device dma mask
which has already been initialized.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The ColdFire PCI configuration space access functions swap addressing
regions to do their work. Just letting the read/write cycles exit
the CPU core (via the ColdFire "nop" instruction) is not enough to
guarantee that the address region remapping has actually completed.
Insert a read back of the mapping register to be absolutely sure
that the remapping has completed.
This fixes an occasional boot hang during the ColdFire PCI initialization
phase.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
A lot of the ColdFire internal peripherals (clocks, timers, interrupt
controllers, etc) are addressed using constants. The only problem with
that is they are not type clean when used with __raw_read/__raw_write
and read/write - they should be of type "void __iomem". This isn't
a problem currently because the IO access functions are local macros.
To switch to using the asm-generic implementations of these we need to
clean up the types. Otherwise you get warnings like this:
In file included from ./arch/m68k/include/asm/mcfsim.h:24:0,
from arch/m68k/coldfire/intc-simr.c:20:
arch/m68k/coldfire/intc-simr.c: In function ‘init_IRQ’:
./arch/m68k/include/asm/m520xsim.h:40:29: warning: passing argument 2 of ‘__raw_writeb’ makes pointer from integer without a cast [-Wint-conversion]
#define MCFINTC0_SIMR (MCFICM_INTC0 + MCFINTC_SIMR)
^
arch/m68k/coldfire/intc-simr.c:182:21: note: in expansion of macro ‘MCFINTC0_SIMR’
__raw_writeb(0xff, MCFINTC0_SIMR);
^
In file included from ./arch/m68k/include/asm/io_no.h:120:0,
from ./arch/m68k/include/asm/io.h:3,
from ./include/linux/io.h:25,
from ./include/linux/irq.h:25,
from ./include/asm-generic/hardirq.h:13,
from ./arch/m68k/include/asm/hardirq.h:25,
from ./include/linux/hardirq.h:9,
from ./include/linux/interrupt.h:13,
from arch/m68k/coldfire/intc-simr.c:16:
./include/asm-generic/io.h:71:22: note: expected ‘volatile void *’ but argument is of type ‘unsigned int’
#define __raw_writeb __raw_writeb
^
./include/asm-generic/io.h:72:20: note: in expansion of macro ‘__raw_writeb’
static inline void __raw_writeb(u8 value, volatile void __iomem *addr)
^
To start this clean up process introduce a macro, iomem(), that converts
a constant address to the correct "void __iomem *" type.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Up to now we have only had support for the PCI bus when running the
ColdFire CPU family with the MMU enabled. The only reason for this was
the incomplete state of the IO remapping and access functions when
running with the MMU disabled.
Recent fixes and improvements to the ColdFire IO access code means we
can now support the PCI bus when running non-MMU enabled as well.
So modify the configuration support to allow it to be selected no matter
what choice of MMU mode is used.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The ColdFire SoC internal peripherals are mapped into virtual address
space using the ACR registers of the cache control unit. This means we
are using a 1:1 physical:virtual mapping for them that does not rely on
page table mappings. We can quickly determine if we are accessing an
internal peripheral device given the physical or vitrual address using
the same range check.
The implications of this mapping is that an ioremap should return the
physical address as the virtual mapping __iomem cookie as well. So fix
ioremap() to deal with this on ColdFire. Of course you need to take
care of this in the iounmap() path as well.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
We need to treat built-in peripherals and bus based address ranges
differently. Local built-in peripherals (and the ColdFire SoC parts
have quite a lot of them) are always native endian - which is big
endian on m68k/ColdFire. Bus based address ranges, like the PCI bus,
are accessed little endian - so we need to byte swap those.
So implement readw/writew and readl/writel functions to deal with
memory mapped accesses correctly based on the address range being
accessed.
This fixes readw/writew and readl/writel so that they can be used in
drivers for native SoC hardware modules (many of which are shared with
other architectures (ARM in Freescale SoC parts for example). And also
drivers for PCI devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Some ColdFire platforms do have real PCI buses, so we should not be
re-defining or otherwise mangling the IO access functions for them.
So when CONFIG_PCI is true use the real io.h support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
All the ColdFire IO access support code has been moved to io_no.h.
This means that all ColdFire support is at least now consistent no
matter whether the MMU is enabled or not for them.
Now that io_mm.h has reverted to only support the traditional m68k MMU
enabled processors we can remove the ColdFire specific definitions.
We can also remove the old ColdFire PCI bus IO access functions.
The new io_no.h uses asm-generic/io.h to provide all the basic support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Use the io_no.h IO access support for all ColdFire systems, no matter
whether configured with MMU enabled or disabled. Previously there was
subtle differences in IO access functions used in both cases, and these
resulted in broken behavior for some drivers.
As observed and reported by Angelo when using MMU enabled systems the
read/write family of functions was using little endian access, while the
non-MMU enabled systems were using native endian. This results in drivers
that are shared across Freescale processors (for some of the common
internal SoC peripherals) not working - since they are wired up for native
endian access.
This problem brings to light issues with PCI bus access and local
peripheral access - but these are not addressed with this fix.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Ultimately we want the ColdFire IO access support to be consisent no matter
whether it is configured with MMU enabled or disabled. To acheive that we
need to get all the ColdFire IO access support code together in one place,
in this case io_no.h. The last big piece not in io_no.h is the PCI bus
support functions.
Define the IO mapping addresses required to use the asm-generic IO
access functions. They can provide everything we need - no need for us
to duplicate or have local in/out or read/write access functions.
Note that this support is not active yet, since we haven't done the
full switch over to using the asm-generic functions yet. And also note
that we do not yet remove the old PCI functions from io_mm.h yet.
Consolodating all this IO access support in a single place will make
it easier in the future to enable PCI bus support for non-MMU enabled
ColdFire (which we currently cannot do).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Create a new header file, kmap.h, that groups all the definitions and
functions associated with the io mapping and remapping.
Currently the functions are spread across raw_io.h and io_mm.h. And in
the future we will want to use these in io_no.h as well. So it makes
sense to move them all together into a single header file.
It is named after the arch/m68k/mm/kmap.c file that actually implements
many of the exported functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The primary and fundamental access macros are really the __raw versions.
So make them the actual implementation for access, and not the read/write
access macros. The read/write macros and functions are built on top of
the raw access (with byte swapping or other actions as required).
This in itself causes no functional change right now. But it will make it
easier to fix and resolve problems with PCI bus access in the future.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
There is nothing really special about the non-MMU m68k IO access functions.
So we can easily switch to using the asm-generic/io.h functions.
The only thing we do need to handle is that historically the m68k IO access
functions for readw/readl/writew/writel use native CPU endian ordering. So
for us on m68k/ColdFire that means they are big-endian. Leave the existing
set of _raw_read/__raw_write and read/write macros in place to deal with
them. (They are ripe for later cleanup, but that is for another patch).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The non-MMU and ColdFire IO access functions will be moving to using the
asm-generic/io.h in the near future. To make that possible we need define
guards around the m68k specific virt_to_phys() and phys_to_virt()
functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Move a copy of the definitions of the *_relaxed() macros into io_no.h
and io_mm.h. This precedes a change to the io_no.h file to use
asm-generic/io.h. They will be removed from io_no.h at that point.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Revive support for 64-bit get_user(), which was disabled in commit
d94af931af ("[PATCH] m68k: clean up uaccess.h") due to a "broken"
typeof in (then brand new) gcc-4.1.
- Keep on using u64 for the temporary, as __typeof__() doesn't drop
the const qualifier,
- Move it into a union (like mips32 does) to get rid of the cast, as
using get_user() to fetch a __user pointer would cause a "cast to
pointer from integer of different size" warning otherwise.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Martijn Coenen <maco@android.com>
ndelay() is supposed to take an unsigned long, but if you define
ndelay() as a macro and the caller pass an unsigned long long instead
of an unsigned long, the unsigned long long to unsigned long cast is
not done and we end up with an "undefined reference to `__udivdi3'"
error at link time.
Fix that by making ndelay() an inline function and then defining dummy
ndelay() macro that redirects to the ndelay() function (it's how most
archs do to implement ndelay()).
Fixes: c8ee038bd1 ("m68k: Implement ndelay() based on the existing udelay() logic")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
[geert: Remove comment now it is no longer a macro]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
We have two ways of getting the current time from a platform at boot
or during suspend: either using read_persistent_clock() or the rtc
class operation. We never need both, so I'm hiding the
read_persistent_clock variant when the generic RTC is enabled.
Since read_persistent_clock() and mktime() are deprecated because of
the y2038 overflow of time_t, we should use the time64_t based
replacements here.
Finally, the dependency on CONFIG_ARCH_USES_GETTIMEOFFSET looks
completely bogus in this case, so let's remove that. It was
added in commit b13b3f51ff ("m68k: fix inclusion of
arch_gettimeoffset for non-MMU 68k classic CPU types") to deal
with arch_gettimeoffset(), which has since been removed from
this file and is unrelated to the RTC functions.
The rtc accessors are only used by classic machines, while
coldfire uses proper RTC drivers, so we can put the old
ifdef back around both functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This fixes a bug in read_persistent_clock() which causes the system
clock to lag the Real Time Clock by one month. The problem was noticed
on a Mac, but theoretically it must also affect Atari, BVME6000 and Q40.
The tm_mon value in the struct rtc_time passed to mach_hwclk() is
zero-based, and atari_mste_hwclk(), atari_tt_hwclk(), bvme6000_hwclk(),
mac_hwclk() and q40_hwclk() all make this adjustment. Unfortunately,
dn_dummy_hwclk(), mvme147_hwclk(), mvme16x_hwclk(), sun3_hwclk() and
sun3x_hwclk() fail to decrement tm_mon. Also m68328_hwclk() assumes
a one-based tm_mon.
Bring these platforms into line and fix read_persistent_clock() so it
works correctly on all m68k platforms.
The datasheets for the RTC devices found on the affected platforms
all confirm that the year is stored as a value in the range 0-99 and
the month is stored as a value in the range 1-12. Please refer to the
datasheets for MC146818 (Apollo), DS1643 (MVME), ICM7170 (Sun 3)
and M48T02 (Sun 3x).
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This was used by the ide, scsi and networking code in the past to
determine if they should bounce payloads. Now that the dma mapping
always have to support dma to all physical memory (thanks to swiotlb
for non-iommu systems) there is no need to this crude hack any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Palmer Dabbelt <palmer@sifive.com> (for riscv)
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Filling in struct siginfo before calling force_sig_info a tedious and
error prone process, where once in a great while the wrong fields
are filled out, and siginfo has been inconsistently cleared.
Simplify this process by using the helper force_sig_fault. Which
takes as a parameters all of the information it needs, ensures
all of the fiddly bits of filling in struct siginfo are done properly
and then calls force_sig_info.
In short about a 5 line reduction in code for every time force_sig_info
is called, which makes the calling function clearer.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
We have a couple of files that try to include asm/compat.h on
architectures where this is available. Those should generally use the
higher-level linux/compat.h file, but that in turn fails to include
asm/compat.h when CONFIG_COMPAT is disabled, unless we can provide
that header on all architectures.
This adds the asm/compat.h for all remaining architectures to
simplify the dependencies.
Architectures that are getting removed in linux-4.17 are not changed
here, to avoid needless conflicts with the removal patches. Those
architectures are broken by this patch, but we have already shown
that they have no users.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull m68knommu update from Greg Ungerer:
"Only a single fix to set the DMA masks in the ColdFire FEC platform
data structure.
This stops the warning from dma-mapping.h at boot time"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: set dma and coherent masks for platform FEC ethernets
Pull siginfo updates from Eric Biederman:
"The work on cleaning up and getting the bugs out of siginfo generation
was largely stalled this round. The progress that was made was the
definition of FPE_FLTUNK. Which is usable to fix many of the cases
where siginfo generation is erroneously generating SI_USER by setting
si_code to 0, that has recently been tagged as FPE_FIXME.
You already have the change by way of the arm64 tree as that
definition was pulled into the arm64 tree to allow fixing the problem
there.
What remains is the second round of fixing for what I thought was a
trivial change to the struct siginfo when put the union in _sigfault
where it belongs. Do to historical reasons 32bit m68k only ensures
that pointers are 2 byte aligned. So I have added a m68k test case
made of BUILD_BUG_ONs to verify I have this fix correct and possibly
catch problems, and I have computed the number of bytes of padding
needed for the _addr_bnd and _addr_pkey cases and just use an array of
characters that size.
For pure paranoia I have written the code so if there is an
architecture out there that does not perform any alignment of
structures it should still work.
With the removal of all of the stale arechitectures this cycle future
work on cleaning up struct siginfo should be much easier. Almost all
of the conflicting si_code definitions have been removed with the
removal of (blackfin, tile, and frv). Plus some of the most difficult
to test cases have simply been removed from the tree.
Which means that with a little luck copy_siginfo_to_user can become a
light weight wrapper around copy_to_user in the next cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
m68k: Verify the offsets in struct siginfo never change.
signal: Correct the offset of si_pkey and si_lower in struct siginfo on m68k
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
Pull removal of in-kernel calls to syscalls from Dominik Brodowski:
"System calls are interaction points between userspace and the kernel.
Therefore, system call functions such as sys_xyzzy() or
compat_sys_xyzzy() should only be called from userspace via the
syscall table, but not from elsewhere in the kernel.
At least on 64-bit x86, it will likely be a hard requirement from
v4.17 onwards to not call system call functions in the kernel: It is
better to use use a different calling convention for system calls
there, where struct pt_regs is decoded on-the-fly in a syscall wrapper
which then hands processing over to the actual syscall function. This
means that only those parameters which are actually needed for a
specific syscall are passed on during syscall entry, instead of
filling in six CPU registers with random user space content all the
time (which may cause serious trouble down the call chain). Those
x86-specific patches will be pushed through the x86 tree in the near
future.
Moreover, rules on how data may be accessed may differ between kernel
data and user data. This is another reason why calling sys_xyzzy() is
generally a bad idea, and -- at most -- acceptable in arch-specific
code.
This patchset removes all in-kernel calls to syscall functions in the
kernel with the exception of arch/. On top of this, it cleans up the
three places where many syscalls are referenced or prototyped, namely
kernel/sys_ni.c, include/linux/syscalls.h and include/linux/compat.h"
* 'syscalls-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux: (109 commits)
bpf: whitelist all syscalls for error injection
kernel/sys_ni: remove {sys_,sys_compat} from cond_syscall definitions
kernel/sys_ni: sort cond_syscall() entries
syscalls/x86: auto-create compat_sys_*() prototypes
syscalls: sort syscall prototypes in include/linux/compat.h
net: remove compat_sys_*() prototypes from net/compat.h
syscalls: sort syscall prototypes in include/linux/syscalls.h
kexec: move sys_kexec_load() prototype to syscalls.h
x86/sigreturn: use SYSCALL_DEFINE0
x86: fix sys_sigreturn() return type to be long, not unsigned long
x86/ioport: add ksys_ioperm() helper; remove in-kernel calls to sys_ioperm()
mm: add ksys_readahead() helper; remove in-kernel calls to sys_readahead()
mm: add ksys_mmap_pgoff() helper; remove in-kernel calls to sys_mmap_pgoff()
mm: add ksys_fadvise64_64() helper; remove in-kernel call to sys_fadvise64_64()
fs: add ksys_fallocate() wrapper; remove in-kernel calls to sys_fallocate()
fs: add ksys_p{read,write}64() helpers; remove in-kernel calls to syscalls
fs: add ksys_truncate() wrapper; remove in-kernel calls to sys_truncate()
fs: add ksys_sync_file_range helper(); remove in-kernel calls to syscall
kernel: add ksys_setsid() helper; remove in-kernel call to sys_setsid()
kernel: add ksys_unshare() helper; remove in-kernel calls to sys_unshare()
...
A change to the generic struct siginfo accidentally changed the offset
of si_offset. Add build time checks to ensure the offsets of all known
fields in struct siginfo never change. This copies the form of similar
changes on x86.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Using this helper allows us to avoid the in-kernel calls to the
sys_mmap_pgoff() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_mmap_pgoff().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As of commit 205e1b7f51 ("dma-mapping: warn when there is no
coherent_dma_mask") the Freescale FEC driver is issuing the following
warning on driver initialization on ColdFire systems:
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 0x40159e20
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc7-dirty #4
Stack from 41833dd8:
41833dd8 40259c53 40025534 40279e26 00000003 00000000 4004e514 41827000
400255de 40244e42 00000204 40159e20 00000009 00000000 00000000 4024531d
40159e20 40244e42 00000204 00000000 00000000 00000000 00000007 00000000
00000000 40279e26 4028d040 40226576 4003ae88 40279e26 418273f6 41833ef8
7fffffff 418273f2 41867028 4003c9a2 4180ac6c 00000004 41833f8c 4013e71c
40279e1c 40279e26 40226c16 4013ced2 40279e26 40279e58 4028d040 00000000
Call Trace:
[<40025534>] 0x40025534
[<4004e514>] 0x4004e514
[<400255de>] 0x400255de
[<40159e20>] 0x40159e20
[<40159e20>] 0x40159e20
It is not fatal, the driver and the system continue to function normally.
As per the warning the coherent_dma_mask is not set on this device.
There is nothing special about the DMA memory coherency on this hardware
so we can just set the mask to 32bits in the platform data for the FEC
ethernet devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This code works fine. The comment is misleading so remove it.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
According to Apple's Developer Notes, all of the early PowerBook models
have their RTC connected to VIA1. Use the VIA clock ops as appropriate.
This was tested on a PowerBook 170.
Don't use the VIA ops when not appropriate. Calling unimplemented clock
or PRAM getter or setter ops can now result in an error instead of
failing silently.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The PMU watchdog will power down the system if the kernel is slow
to start up, e.g. due to unpacking a large initrd. The powerpc
version of this driver (via-pmu.c) has a solution for the same
problem. It uses this call sequence:
setup_arch
find_via_pmu
init_pmu
...
arch_initcall
via_pmu_start
Bring via-pmu68k.c into line with via-pmu.c to fix this issue.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The algorithm used in baboon_irq() appears to be subject to a race
condition: an IRQ flag could be lost if asserted between the MOV
instructions from and to the interrupt flag register. However,
testing shows that the write to the flag register has no effect.
Rewrite this loop to remove the apparent race condition.
No-one seems to know how to clear Baboon IRQ flags, or whether
that's even possible, so add a comment about this.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Stan's tests showed that PDMA improves sequential read performance by
a factor of 5 on a PowerBook 190. Last time I tried this on a
PowerBook 520 it didn't work, so let's not enable it there until
it can be tested with the present mac_scsi driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Apparently these Dayna cards don't have a pseudoslot declaration ROM
which means they can't be probed like NuBus cards.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.
In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.
A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return. I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.
The files that saw the largest change from this had these frame sizes
before, and much less with my patch:
fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]
In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
include/linux/dmaengine.h: In function 'dma_maxpq':
include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]
This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.
I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.
Vineet said:
: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2. bloat-o-meter reports code size improvements as gcc elides the
: generated code for stack return.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365
Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
except, again, POLLFREE and POLL_BUSY_LOOP.
With this, we finally get to the promised end result:
- POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
stray instances of ->poll() still using those will be caught by
sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
to the clk rate protection support added by Jerome Brunet. This feature
will allow consumers to lock in a certain rate on the output of a clk so
that things like audio playback don't hear pops when the clk frequency
changes due to shared parent clks changing rates. Currently the clk
API doesn't guarantee the rate of a clk stays at the rate you request
after clk_set_rate() is called, so this new API will allow drivers
to express that requirement. Beyond this, the core got some debugfs
pretty printing patches and a couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h file
causes small one-liners in all the architecture Kbuild files. Overall, the
driver diff seems to be the normal stuff that comes all the time to
fix little problems here and there and to support new hardware.
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bGPp
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
This pull requests contains a consolidation of the generic no-IOMMU code,
a well as the glue code for swiotlb. All the code is based on the x86
implementation with hooks to allow all architectures that aren't cache
coherent to use it. The x86 conversion itself has been deferred because
the x86 maintainers were a little busy in the last months.
-----BEGIN PGP SIGNATURE-----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=Nrl9
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"Except for a runtime warning fix from Christian this is all about
consolidation of the generic no-IOMMU code, a well as the glue code
for swiotlb.
All the code is based on the x86 implementation with hooks to allow
all architectures that aren't cache coherent to use it.
The x86 conversion itself has been deferred because the x86
maintainers were a little busy in the last months"
* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
arm64: use swiotlb_alloc and swiotlb_free
arm64: replace ZONE_DMA with ZONE_DMA32
mips: use swiotlb_{alloc,free}
mips/netlogic: remove swiotlb support
tile: use generic swiotlb_ops
tile: replace ZONE_DMA with ZONE_DMA32
unicore32: use generic swiotlb_ops
ia64: remove an ifdef around the content of pci-dma.c
ia64: clean up swiotlb support
ia64: use generic swiotlb_ops
ia64: replace ZONE_DMA with ZONE_DMA32
swiotlb: remove various exports
swiotlb: refactor coherent buffer allocation
swiotlb: refactor coherent buffer freeing
swiotlb: wire up ->dma_supported in swiotlb_dma_ops
swiotlb: add common swiotlb_map_ops
swiotlb: rename swiotlb_free to swiotlb_exit
x86: rename swiotlb_dma_ops
powerpc: rename swiotlb_dma_ops
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
- First part of an overhaul of the NuBus subsystem, to bring it up to
modern driver model standards,
- A race condition fix for Mac,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PZNx
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- first part of an overhaul of the NuBus subsystem, to bring it up to
modern driver model standards
- a race condition fix for Mac
- defconfig updates
* tag 'm68k-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
MAINTAINERS: Add NuBus subsystem entry
m68k/mac: Fix race conditions in OSS interrupt dispatch
nubus: Add support for the driver model
nubus: Add expansion_type values for various Mac models
nubus: Adopt standard linked list implementation
nubus: Rename struct nubus_dev
nubus: Rework /proc/bus/nubus/s/ implementation
nubus: Generalize block resource handling
nubus: Clean up whitespace
nubus: Remove redundant code
nubus: Call proc_mkdir() not more than once per slot directory
nubus: Validate slot resource IDs
nubus: Fix log spam
nubus: Use static functions where possible
nubus: Fix up header split
nubus: Avoid array underflow and overflow
m68k/defconfig: Update defconfigs for v4.15-rc1
It doesn't actually do anything. Merge its help text into
EXTRA_FIRMWARE.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware")
Fixes: 0946b2fb38 ("firmware: cleanup FIRMWARE_IN_KERNEL message")
Signed-off-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The siginfo structure has all manners of holes with the result that a
structure initializer is not guaranteed to initialize all of the bits.
As we have to copy the structure to userspace don't even try to use
a structure initializer. Instead use clear_siginfo followed by initializing
selected fields. This gives a guarantee that uninitialized kernel memory
is not copied to userspace.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The interrupt dispatch algorithm used in the OSS driver seems to be
subject to race conditions: an IRQ flag could be lost if asserted between
the MOV instructions from and to the interrupt flag register. But testing
shows that the write to the flag register has no effect, so rewrite the
algorithm without the theoretical race condition.
There is a second theoretical race condition here. When oss_irq() is
called with say, IPL == 2 it will invoke the SCSI interrupt handler.
The SCSI IRQ is then cleared by the mac_scsi driver. If SCSI and NuBus
IRQs are now asserted together, oss_irq() will be invoked with IPL == 3
and the mac_scsi interrupt handler can be re-entered. This re-entrance
issue is not limited to SCSI and could affect NuBus and ADB drivers too.
Fix it by splitting up oss_irq() into separate handlers for each IPL.
No-one seems to know how OSS irq flags can be cleared, if at all, so add
a comment to this effect (actually reinstate one I previously removed).
Testing showed that a slot IRQ with no handler can remain asserted (in
this case a Radius video card) without causing problems for other IRQs.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add an expansion slot attribute to allow drivers to properly handle
cards like Comm Slot cards and PDS cards without declaration ROMs.
This clarifies the logic for the Centris 610 model which has no
Comm Slot but has an optional on-board SONIC device.
Cc: "David S. Miller" <davem@davemloft.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Lift the code from x86 so that we behave consistently. In the future we
should probably warn if any of these is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Construct the init thread stack in the linker script rather than doing it
by means of a union so that ia64's init_task.c can be got rid of.
The following symbols are then made available from INIT_TASK_DATA() linker
script macro:
init_thread_union
init_stack
INIT_TASK_DATA() also expands the region to THREAD_SIZE to accommodate the
size of the init stack. init_thread_union is given its own section so that
it can be placed into the stack space in the right order. I'm assuming
that the ia64 ordering is correct and that the task_struct is first and the
thread_info second.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Will Deacon <will.deacon@arm.com> (arm64)
Tested-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Now that every architecture is using the generic clkdev.h file
and we no longer include asm/clkdev.h anywhere in the tree, we
can remove it.
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
Commit 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT
program type") introduced the bpf_perf_event_data structure which
exports the pt_regs structure. This is OK for multiple architectures
but fail for s390 and arm64 which do not export pt_regs. Programs
using them, for example, the bpf selftest fail to compile on these
architectures.
For s390, exporting the pt_regs is not an option because s390 wants
to allow changes to it. For arm64, there is a user_pt_regs structure
that covers parts of the pt_regs structure for use by user space.
To solve the broken uapi for s390 and arm64, introduce an abstract
type for pt_regs and add an asm/bpf_perf_event.h file that concretes
the type. An asm-generic header file covers the architectures that
export pt_regs today.
The arch-specific enablement for s390 and arm64 follows in separate
commits.
Reported-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Fixes: 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT program type")
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-and-tested-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit be7635e728 ("arch, ftrace: for KASAN put hard/soft IRQ entries
into separate sections") added a new linker section, SOFTIRQENTRY_TEXT,
to the linker scripts for most architectures. It didn't add it to any of
the linker scripts for the m68k architecture. This was not really a problem
because it is only defined if either of CONFIG_FUNCTION_GRAPH_TRACER or
CONFIG_KASAN are enabled - which can never be true for m68k.
However commit 229a718605 ("irq: Make the irqentry text section
unconditional") means that SOFTIRQENTRY_TEXT is now always defined. So on
m68k we now end up with a separate ELF section for .softirqentry.text
instead of it being part of the .text section. On some m68k targets in some
configurations this can also cause a fatal link error:
LD vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: section .softirqentry.text loaded at [0000000010de10c0,0000000010de12dd] overlaps section .rodata loaded at [0000000010de10c0,0000000010e0fd67]
To fix add in the missing SOFTIRQENTRY_TEXT section into the m68k linker
scripts. I noticed that m68k is also missing the IRQENTRY_TEXT section,
so this patch also adds an entry for that too.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This fixes a missed function prototype callback from the timer conversions.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20171123221902.GA75727@beast
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture
doesn't support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAloLSrYLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYOMuQ//XXD94uNPYavrgXzGsAtg+I+LEm+xyk4T0dX5fxfj
amXX49MHoGemjsBgzJlkQMMFqwDEdkKyEuFnEuy6OeowYCyD6zW0MJ3MwP9OosNJ
PNTdGZIfSvxPYEW8cR9AdK3iQ2loMBZnYhd+O/oVjSugULLW2DNa7r2VRktcCKoh
8Ob/8gL6Y9xEYJBRszhrBwKTa/hU8IThxxozBFzN7I3LIKyFboSTcwXGLAHow43g
4anCTjWTaDcoU2JwY6UTRKRRTV+gD0ZRcsZfd8lNNb5rtMVZkBVOHbF14SMAmw1r
kSgRcU3+WIFPhK/8wBYqtGZZGnOgFBTHVeqow3AdS728pBWlWl8niTK0DiIgCd3m
qzScF6SqfN1bCZkZAy8FUV2l0DPYKS6lvyNkf00Eb2W/f6LEqAcjCi2QDDxRfaw+
Vm97nPUiM+uXNy/6KtAy6ChdprSqx12/edXPp7Y3H2rS/+Dmr6exeix+wb7QUN8W
JI7ZRHo4JLaJZk/XrZtGX/6jnN1Jo7vfApQOmYDY7kE1iGtOU/LQQj8gcZRVQxML
4soN6ivSmZX2k03LabWHpYQ8QiyCSYChLC+Az7rQH47LDLeu1IdTJu6orpXpaxyo
ymzEWlHbmF7mE66X4g/Up/eAYk2YLUA3rKLGVjAIaWDBzHftSFg5EaAnqMADC1G2
hSo=
=ALJf
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
- More printk modernization,
- Various cleanups and fixes (incl. a race condition) for Mac,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cuxe
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- more printk modernization
- various cleanups and fixes (incl. a race condition) for Mac
- defconfig updates
* tag 'm68k-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.14-rc7
m68k/mac: Add mutual exclusion for IOP interrupt polling
m68k/mac: Disentangle VIA/RBV and NuBus initialization
m68k/mac: Disentangle VIA and OSS initialization
m68k/mac: More printk modernization
The IOP interrupt handler iop_ism_irq() is used by the adb-iop
driver to poll for ADB request completion. Unfortunately, it is not
re-entrant. Fix the race condition by adding an iop_ism_irq_poll()
function with suitable mutual exclusion.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The Nubus subsystem should not be concerned with differences between VIA,
RBV and OSS platforms. It should be portable across Macs and PowerMacs.
This goal has implications for the initialization code relating to bus
locking and slot interrupts.
During Nubus initialization, bus transactions are "unlocked": on VIA2 and
RBV machines, via_nubus_init() sets a bit in the via2[gBufB] register to
allow bus-mastering Nubus cards to arbitrate for the bus. This happens
upon subsys_initcall(nubus_init). But because nubus_init() has no effect
on card state, this sequence is arbitrary.
Moreover, when Penguin is used to boot Linux, the bus is already unlocked
when Linux starts. On OSS machines there's no attempt to unlock Nubus
transactions at all. (Maybe there's no benefit on that platform or maybe
no-one knows how.)
All of this demonstrates that there's no benefit in locking out
bus-mastering cards, as yet. (If the need arises, we could lock the bus
for the duration of a timing-critical operation.) NetBSD unlocks the
Nubus early (at VIA initialization) and we can do the same.
via_nubus_init() is also responsible for some VIA interrupt setup that
should happen earlier than subsys_initcall(nubus_init). And actually, the
Nubus subsystem need not be involved with slot interrupts: SLOT2IRQ
works fine because Nubus slot IRQs are geographically assigned
(regardless of platform).
For certain platforms with PDS slots, some Nubus IRQs may be platform
IRQs and this is not something that the NuBus subsystem should worry
about. So let's invoke via_nubus_init() earlier and make the platform
responsible for bus unlocking and interrupt setup instead of the NuBus
subsystem.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
macintosh_config->via_type is meaningless on Mac IIfx (i.e. the only
model with OSS chip), so skip the via_type switch statement.
Call oss_init() before via_init() because it is more important and
because that is the right place to initialize the oss_present flag.
On this model, bringing forward oss_init() and delaying via_init()
is no problem because those functions are independent.
The only requirement here is that oss_register_interrupts() happens
after via_init(). That is, mac_init_IRQ() happens after config_mac().
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Log message fragments used to be printed on one line but now get split up.
Fix this. Also, suppress log spam that merely prints known pointer values.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add support for Sysam stmark2 board, an open hardware embedded
Linux board, see http://sysam.it/cff_stmark2.html for any info.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This patch adds initial module base address and irq for dspi0.
It also defines the dspi0 clock to be used by the Freescale driver.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
It is possible to select INPUT_M68K_BEEP in a nommu configuration. This
results in the following link error:
drivers/input/misc/m68kspkr.o: In function `m68kspkr_event':
m68kspkr.c:(.text+0x3a): undefined reference to `mach_beep'
m68kspkr.c:(.text+0x5e): undefined reference to `mach_beep'
m68kspkr.c:(.text+0x78): undefined reference to `mach_beep'
drivers/input/misc/m68kspkr.o: In function `m68kspkr_init':
m68kspkr.c:(.init.text+0x4): undefined reference to `mach_beep'
Pull the mach_beep definition in setup.c to avoid it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The Freescale ColdFire M5441x system-on-chip parts have full paged MMU
hardware support. So far though we have only allowed them to be
configured for use in non-MMU mode.
All required kernel changes to support operation of the M5441x parts
with MMU enabled have been pushed into the kernel, so now we can allow
it to be configured and used with the MMU enabled.
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The m68k pg_data_table is a fix size array defined in arch/m68k/mm/init.c.
Index numbers within it are defined based on memory size. But for Coldfire
these don't take into account a non-zero physical RAM base address, and this
causes us to access past the end of this array at system start time.
Change the node shift calculation so that we keep the index inside its range.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The M54[78]x ColdFire parts are not the only members of the ColdFire family
that have an MMU. But currently some of the early MMU initialization code
is inside the startup code specific to only the ColdFire M54[78]x parts.
Move that early ColdFire MMU init code so that it is run for other ColdFire
parts running with MMU enabled.
Specifically this means that the MMU initialization code will now also be
run for the ColdFire M5441x parts when running with MMU enabled.
The code move meant that the extern definition for the mmu_context_init()
function had to be moved as well. To make it clear that is ColdFire specific
I have renamed that with a "cf_" in front of it and put its extern definition
in the mcfmmu.h (which is already included by the setup code).
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After we removed all the dead wood it turns out only two architectures
actually implement dma_cache_sync as a real op: mips and parisc. Add
a cache_sync method to struct dma_map_ops and implement it for the
mips defualt DMA ops, and the parisc pa11 ops.
Note that arm, arc and openrisc support DMA_ATTR_NON_CONSISTENT, but
never provided a functional dma_cache_sync implementations, which
seems somewhat odd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Pull m68knommu updates from Greg Ungerer:
"Only two changes. One removes unused code, the other makes local clock
code arguments consistent with generic clock code"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: remove dead code
m68k: allow NULL clock for clk_get_rate
With gcc 4.1.2:
include/linux/swapops.h: In function ‘swp_entry_to_pmd’:
include/linux/swapops.h:294: warning: missing braces around initializer
include/linux/swapops.h:294: warning: (near initialization for ‘(anonymous).pmd’)
Due to a GCC zero initializer bug (#53119), the standard "(pmd_t){ 0 }"
initializer is not accepted by all GCC versions.
In addition, on m68k pmd_t is an array instead of a single value, so we
need "(pmd_t){ { 0 }, }" instead of "(pmd_t){ 0 }".
Based on commit 9157259d16 ("mm: add pmd_t initializer __pmd() to
work around a GCC bug.") for sparc32.
Fixes: 616b837153 ("mm: thp: enable thp migration in generic path")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge more updates from Andrew Morton:
- most of the rest of MM
- a small number of misc things
- lib/ updates
- checkpatch
- autofs updates
- ipc/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (126 commits)
ipc: optimize semget/shmget/msgget for lots of keys
ipc/sem: play nicer with large nsops allocations
ipc/sem: drop sem_checkid helper
ipc: convert kern_ipc_perm.refcount from atomic_t to refcount_t
ipc: convert sem_undo_list.refcnt from atomic_t to refcount_t
ipc: convert ipc_namespace.count from atomic_t to refcount_t
kcov: support compat processes
sh: defconfig: cleanup from old Kconfig options
mn10300: defconfig: cleanup from old Kconfig options
m32r: defconfig: cleanup from old Kconfig options
drivers/pps: use surrounding "if PPS" to remove numerous dependency checks
drivers/pps: aesthetic tweaks to PPS-related content
cpumask: make cpumask_next() out-of-line
kmod: move #ifdef CONFIG_MODULES wrapper to Makefile
kmod: split off umh headers into its own file
MAINTAINERS: clarify kmod is just a kernel module loader
kmod: split out umh code into its own file
test_kmod: flip INT checks to be consistent
test_kmod: remove paranoid UINT_MAX check on uint range processing
vfat: deduplicate hex2bin()
...
Patch series "Define CPU_BIG_ENDIAN or warn for inconsistencies", v3.
While working on enabling queued rwlock on SPARC, found this following
code in include/asm-generic/qrwlock.h which uses CONFIG_CPU_BIG_ENDIAN to
clear a byte.
static inline u8 *__qrwlock_write_byte(struct qrwlock *lock)
{
return (u8 *)lock + 3 * IS_BUILTIN(CONFIG_CPU_BIG_ENDIAN);
}
Problem is many of the fixed big endian architectures don't define
CPU_BIG_ENDIAN and clears the wrong byte.
Define CPU_BIG_ENDIAN for all the fixed big endian architecture to fix it.
Also found few more references of this config parameter in
drivers/of/base.c
drivers/of/fdt.c
drivers/tty/serial/earlycon.c
drivers/tty/serial/serial_core.c
Be aware that this may cause regressions if someone has worked-around
problems in the above code already. Remove the work-around.
Here is our original discussion
https://lkml.org/lkml/2017/5/24/620
Link: http://lkml.kernel.org/r/1499358861-179979-2-git-send-email-babu.moger@oracle.com
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
- Restore symbol versions for symbols exported from assembly,
- Defconfig updates,
- Mac fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/iJN
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- restore symbol versions for symbols exported from assembly
- defconfig updates
- Mac fixes
* tag 'm68k-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/mac: Avoid soft-lockup warning after mach_power_off
m68k/mac: Don't hang waiting for Cuda power-down command
m68k: Restore symbol versions for symbols exported from assembly
m68k/defconfig: Update defconfigs for v4.13-rc1
As CONFIG_RTC_DRV_M5441x doesn't exist because the driver never made it
upstream, there is no device to register. Remove code that is never
compiled and init_BSP() as it doesn't do anything.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Finn Thain