enter_lmode() and exit_lmode() modify the guest's EFER.LMA before calling
vmx_set_efer(). However, the latter function depends on the value of EFER.LMA
to determine whether MSR_KERNEL_GS_BASE needs reloading, via
vmx_load_host_state(). With EFER.LMA changing under its feet, it took the
wrong choice and corrupted userspace's %gs.
This causes 32-on-64 host userspace to fault.
Fix not touching EFER.LMA; instead ask vmx_set_efer() to change it.
Signed-off-by: Avi Kivity <avi@redhat.com>
Breaking here dropped us to the default code which always sends a SIGILL
to the current process, no matter what the CU2 notifier says.
[Ralf: Currently this only hurts on Cavium and possibly some out of tree
platforms.]
Signed-off-by: Jesper Nilsson <jesper@jni.nu>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1391/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When trying to netboot a Linksys WRT54GS WLAN router, the bootup fails,
because of following error message:
...
[ 0.424000] b44: b44.c:v2.0
[ 0.424000] b44: Invalid MAC address found in EEPROM
[ 0.432000] b44 ssb0:1: Problem fetching invariants of chip,aborting
[ 0.436000] b44: probe of ssb0:1 failed with error -22
...
The router uses a CFE bootloader, but most of the needed environment
variables for network card initialization, are not available from CFE
via printenv and even though not via cfe_getenv().
The required environment variables are saved in a special partition
in flash memory. The attached patch implement nvram_getenv and enables
bootup via NFS root on my router.
Most of the patch is extracted from the OpenWrt subversion repository and
stripped down and cleaned up to just fix this issue.
[Ralf: sorted out header file inclusions. Lots of unneded headers and such
that should have been included.]
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Reviewed-by: Phil Sutter <phil@nwl.cc>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/1359/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch declare the rtc device present on systems with clock compatible
with the mc146818 and handled by rtc-cmos. Introduce a new Kconfig entry
because there are some systems without rtc_cmos compatible clock.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
To: linux-mips@linux-mips.org
Cc: aba@not.so.argh.org
Patchwork: http://patchwork.linux-mips.org/patch/1320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The fragile MT sys_sched_setaffinity wrapper needs its regular dose of
fixes.
Nose-poked-at-pile-o-crap-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When exiting from loongson2_exit(), we need to reset the counter
register too, this patch adds a function reset_counters() to do it, by
the way, this function will be shared by Perf.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1199/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the low-level sleepcode into per-cpu functions instead of
relying on compile-time-defined cpu type.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds an inline function in_module() to check which space the
instruction pointer in, kernel space or module space.
Note: This will not work when the kernel space and module space are the
same. If they are the same, we need to modify scripts/recordmcount.pl,
ftrace_make_nop/call() and the other related parts to ensure the
enabling/disabling of the calling site to _mcount is right for both
kernel and module.
[Ralf: It also is still incorrect for some 64-bit kernels.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1232/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the help of uasm this patch encodes the instructions of the dynamic
function tracer in ftrace_dyn_arch_init() when initializing it.
As a result we can remove the dynamic encoding of instructions in
ftrace_make_nop()/call(), ftrace_enable_ftrace_graph_caller() and remove
the macro jump_insn_encode() and at last this reduce the overhead of
dynamic Function Tracer. This also is cleaner.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1230/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds some cleanups of the instructions:
o use macros instead of magic numbers
o use macros instead of variables to reduce some overhead
o add new macro for the jal instruction
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1229/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For 32-bit kernel the -mmcount-ra-address option of gcc 4.5 emits one
extra instruction before calling to _mcount so we need to use a different
"b 1f" for it.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1228/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As documented in the GCC 4.5 docs [1] -mmcount-ra-address uses register
$12 to pass the stack offset of the return address to the _mcount function.
On 64-bit kernels $12 is t0 but in 32-bit kernels it is t4 so we need to
use $12 instead of t0 here to be correct for both kernel types.
[1] GCC documentation: MIPS Options
http://gcc.gnu.org/onlinedocs/gcc/MIPS-Options.html
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1227/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The return value of gpio_to_irq() is not a pointer but an integer.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto <anemo@mba.ocn.ne.jp> spotted that this had been incorrectly
removed in a previous patch
Signed-off-by: Chris Dearman <chris@mips.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1213/
Tested-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function _wrmsr() called by divil_lbar_disable()/enable() should be
called with the offset as the argument.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Zhang Le <r0bertz@gentoo.org>
Patchwork: http://patchwork.linux-mips.org/patch/1252/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add several missing RDMSRs for IDE and USB are missing to avoid the
agressive modification of the high 32 bits of the MSR.
Without this patch some usb devices may fail after printing "reset ehci
host ....." when reading the partition information.
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Zhang Le <r0bertz@gentoo.org>
Cc: Hu Hongbing <huhb@lemote.com>
Patchwork: http://patchwork.linux-mips.org/patch/1250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PORT_AR7 has the correct TRIG flag (UART_FCR_R_TRIG_00) as well as
UART_CAP_AFE being set. This fixes UART on TNETD7300 revision 0x02,
which would otherwise mangle some characters, no side effects on
other revisions.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1246/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reimplement augmented RB-trees without sprinkling extra branches
all over the RB-tree code (which lives in the scheduler hot path).
This approach is 'borrowed' from Fabio's BFQ implementation and
relies on traversing the rebalance path after the RB-tree-op to
correct the heap property for insertion/removal and make up for
the damage done by the tree rotations.
For insertion the rebalance path is trivially that from the new
node upwards to the root, for removal it is that from the deepest
node in the path from the to be removed node that will still
be around after the removal.
[ This patch also fixes a video driver regression reported by
Ali Gholami Rudi - the memtype->subtree_max_end was updated
incorrectly. ]
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Ali Gholami Rudi <ali@rudi.ir>
Cc: Fabio Checconi <fabio@gandalf.sssup.it>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1275414172.27810.27961.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes on wrong function name in include/plat/sdhci.h for Samsung.
The 's5pc100_default_sdhci0()' function should be chnaged to
's5pv210_default_sdhci0()'. Because 's5pv210_default_sdhci0()' must be pair.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S5P6442 PLL setting announce message incorrectly displays S5P6440
as the SoC. Change it to S5P6442.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following compilation problem if only NCP machine
is selected:
arch/arm/mach-s3c64xx/s3c6410.c: In function 's3c6410_map_io':
arch/arm/mach-s3c64xx/s3c6410.c:51: error: implicit declaration of function 's3c6410_default_sdhci2'
And also adds missed 's3c6400_default_sdhci2'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix and added comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
1. Corrected shift values of I2S and UART clocks (CLK_GATE_IP3), which were
defined incorrectly.
2. Corrected shift values of sclk_audio, uclk1, sclk_fimd, sclk_mmc,
sclk_spi, sclk_pwm, which had duplicated .enable/.ctrlbit with their
twins defined in struct clk init_clocks_disable[] and struct clk
init_clocks[]. We've changed their .enable/.ctrlbit to use CLK_SRC_MASK
register to avoid the duplicated clock problem described below.
NOTE: Duplicated Clock Problem
Please note that each clock definition should access different control
register; otherwise, the system may suffer lockups. For example, if we
have two clock definitions "a" and "b" which access the same register
(and the shift value). Then, when we do:
module A
clk = clk_get("a");
clk->clk_enable(clk);
module B (context switch)
clk = clk_get("b");
clk->clk_enable(clk);
do something with clk.
clk->clk_disable(clk);
module A (context switch)
do something with clk
* At this point, the system may hang.
Therefore, there should be no clock definitions with the same contol
register/shift. If we need to create "aliases", then, creating child
clocks sharing the clock should be fine.
3. Corrected other sclk_* shift values and access registers.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and message fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes bug on eint type set function, s5p_irq_eint_set_type().
In the IRQ_TYPE_EDGE_FALLING case, S5P_EXTINT_FALLEDGE is right
instead of S5P_EXTINT_RISEEDGE
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6205/1: perf: ensure counter delta is treated as unsigned
ARM: 6202/1: Do not ARM_DMA_MEM_BUFFERABLE on RealView boards with L210/L220
ARM: 6201/1: RealView: Do not use outer_sync() on ARM11MPCore boards with L220
ARM: 6195/1: OMAP3: pmu: make CPU_HAS_PMU dependent on OMAP3_EMU
ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore
ARM: 6193/1: RealView: Align the machine_desc.phys_io to 1MB section
ARM: 6192/1: VExpress: Align the machine_desc.phys_io to 1MB section
ARM: 6188/1: Add a config option for the ARM11MPCore DMA cache maintenance workaround
ARM: 6187/1: The v6_dma_inv_range() function must preserve data on SMP
ARM: 6186/1: Avoid the CONSISTENT_DMA_SIZE warning on noMMU builds
ARM: mx3: mx31lilly: fix build error for !CONFIG_USB_ULPI
[ARM] mmp: fix build failure due to IRQ_PMU depends on ARCH_PXA
[ARM] pxa/mioa701: fix camera regression
[ARM] pxa/z2: fix flash layout to final version
[ARM] pxa/z2: fix missing include in battery driver
[ARM] pxa: fix incorrect gpio type in udc_pxa2xx.h
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Fix incorrect branches event on AMD CPUs
perf tools: Fix find tids routine by excluding "." and ".."
x86: Send a SIGTRAP for user icebp traps
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Cc: <stable@kernel.org>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While doing some performance counter validation tests on some
assembly language programs I noticed that the "branches:u"
count was very wrong on AMD machines.
It looks like the wrong event was selected.
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: <stable@kernel.org>
LKML-Reference: <alpine.DEB.2.00.1007011526010.23160@cl320.eecs.utk.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
RealView boards with certain revisions of the L210/L220 cache controller
may have issues (hardware deadlock) with the mandatory barriers (DSB
followed by an L2 cache sync) when ARM_DMA_MEM_BUFFERABLE is enabled.
The patch disables ARM_DMA_MEM_BUFFERABLE for these boards.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RealView boards with certain revisions of the L220 cache controller (ARM11*
processors only) may have issues (hardware deadlock) with the recent changes to
the mb() barrier implementation (DSB followed by an L2 cache sync). The patch
redefines the RealView ARM11MPCore mandatory barriers without the outer_sync()
call.
Cc: <stable@kernel.org>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU performance event counters on v7 cores will only operate
if either the NIDEN or DBGEN signals are driven high.
For the OMAP3 platform, these signals are driven low by default
but DBGEN can be asserted by selecting the OMAP3_EMU Kconfig option,
which enables the virtual clock for hardware debugging peripherals.
Acked-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux expects that if a CPU modifies a memory location, then that
modification will eventually become visible to other CPUs in the system.
On an ARM11MPCore processor, loads are prioritised over stores so it is
possible for a store operation to be postponed if a polling loop immediately
follows it. If the variable being polled indirectly depends on the outstanding
store [for example, another CPU may be polling the variable that is pending
modification] then there is the potential for deadlock if interrupts are
disabled. This deadlock occurs in the KGDB testsuire when executing on an
SMP ARM11MPCore configuration.
This patch changes the definition of cpu_relax() to smp_mb() for ARMv6 cores,
forcing a flushing of the write buffer on SMP systems before the next load
takes place. If the Kernel is not compiled for SMP support, this will expand
to a barrier() as before.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When not aligned, random bits could be written in the initial page table
by the __create_page_tables() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When not aligned, random bits could be written in the initial page table
by the __create_page_tables() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit f4d6477f introduced a workaround for the lack of hardware
broadcasting of the cache maintenance operations on ARM11MPCore.
However, the workaround is only valid on CPUs that do not do speculative
loads into the D-cache.
This patch adds a Kconfig option with the corresponding help to make the
above clear. When the DMA_CACHE_RWFO option is disabled, the kernel
behaviour is that prior to the f4d6477f commit. This also allows ARMv6
UP processors with speculative loads to work correctly.
For other processors, a different workaround may be needed.
Cc: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A recent patch for DMA cache maintenance on ARM11MPCore added a write
for ownership trick to the v6_dma_inv_range() function. Such operation
destroys data already present in the buffer. However, this function is
used with with dma_sync_single_for_device() which is supposed to
preserve the existing data transfered into the buffer. This patch adds a
combination of read/write for ownership to preserve the original data.
Reported-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This macro is not defined when !CONFIG_MMU so this patch moves the
CONSISTENT_* definitions to the CONFIG_MMU section.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The x3950 family can have as many as 256 PCI buses in a single system, so
change the limits to the maximum. Since there can only be 256 PCI buses in one
domain, we no longer need the BUG_ON check.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
LKML-Reference: <20100701004519.GQ15515@tux1.beaverton.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Typo in down_spin() meant it only read the low 32 bits of the
"serve" value, instead of the full 64 bits. This results in the
system hanging when the values in ticket/serve get larger than
32-bits. A big enough system running the right test can hit this
in a just a few hours.
Broken since 883a3acf5b
[IA64] Re-implement spinaphores using ticket lock concepts
Reported via IRC by Bjorn Helgaas
Signed-off-by: Tony Luck <tony.luck@intel.com>
Before we had a generic breakpoint layer, x86 used to send a
sigtrap for any debug event that happened in userspace,
except if it was caused by lazy dr7 switches.
Currently we only send such signal for single step or breakpoint
events.
However, there are three other kind of debug exceptions:
- debug register access detected: trigger an exception if the
next instruction touches the debug registers. We don't use
it.
- task switch, but we don't use tss.
- icebp/int01 trap. This instruction (0xf1) is undocumented and
generates an int 1 exception. Unlike single step through TF
flag, it doesn't set the single step origin of the exception
in dr6.
icebp then used to be reported in userspace using trap signals
but this have been incidentally broken with the new breakpoint
code. Reenable this. Since this is the only debug event that
doesn't set anything in dr6, this is all we have to check.
This fixes a regression in Wine where World Of Warcraft got broken
as it uses this for software protection checks purposes. And
probably other apps do.
Reported-and-tested-by: Alexandre Julliard <julliard@winehq.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: 2.6.33.x 2.6.34.x <stable@kernel.org>
The os-linux/mem.c file calls fchmod function, which is declared in sys/stat.h
header file, so include it. Fixes build breakage under FC13.
Signed-off-by: Liu Aleaxander <Aleaxander@gmail.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let's use the standard L1_CACHE_ALIGN macro instead.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, Calgary: Increase max PHB number
x86: Fix rebooting on Dell Precision WorkStation T7400
x86: Fix vsyscall on gcc 4.5 with -Os
x86, pat: Proper init of memtype subtree_max_end
um, hweight: Fix UML boot crash due to x86 optimized hweight
x86, setup: Set ax register in boot vga query
percpu, x86: Avoid warnings of unused variables in per cpu
x86, irq: Rename gsi_end gsi_top, and fix off by one errors
x86: use __ASSEMBLY__ rather than __ASSEMBLER__
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
powerpc/5200: fix lite5200 ethernet phy address
powerpc/5200: Fix build error in sound code.
powerpc/5200: fix oops during going to standby
powerpc/5200: add lite5200 onboard I2C eeprom and flash
maintainers: Add git trees for SPI and device tree
of: Drop properties with "/" in their name
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fix de2104x driver failing to readout MAC address correctly
alpha: Detect Super IO chip, no IDE on Avanti, enable EPP19
alpha: fix pci_mmap_resource API breakage
alpha: fix __arch_hweight32 typo
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix mpic_resume on early G5 macs
powerpc: rtas_flash needs to use rtas_data_buf
powerpc: Unconditionally enabled irq stacks
powerpc/kexec: Wait for online/possible CPUs only.
powerpc: Disable CONFIG_SYSFS_DEPRECATED
powerpc/boot: Remove addRamdisk.c since it is now unused
powerpc: Move kdump default base address to 64MB on 64bit
powerpc: Remove dead CONFIG_HIGHPTE
powerpc/fsl-booke: Move loadcam_entry back to asm code to fix SMP ftrace
powerpc/fsl-booke: Fix InstructionTLBError execute permission check
Newer systems (x3950M2) can have 48 PHBs per chassis and 8
chassis, so bump the limits up and provide an explanation
of the requirements for each class.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Corinna Schultz <cschultz@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
LKML-Reference: <20100624212647.GI15515@tux1.beaverton.ibm.com>
[ v2: Fixed build bug, added back PHBS_PER_CALGARY == 4 ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As reported by Sergei, a couple of braces were missing after
the WARN removal patch.
[07/22] OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
https://patchwork.kernel.org/patch/100756/
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: fixed patch description per Anand's E-mail]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Need to mask out the existing event bits before OR'ing in
the new ones.
Noticed by Peter Zijlstra.
Signed-off-by: David S. Miller <davem@davemloft.net>
The function begins and ends with a read_lock. The latter is changed to a
read_unlock.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@locked@
expression E1;
position p;
@@
read_lock(E1@p,...);
@r exists@
expression x <= locked.E1;
expression locked.E1;
expression E2;
identifier lock;
position locked.p,p1,p2;
@@
*lock@p1 (E1@p,...);
... when != E1
when != \(x = E2\|&x\)
*lock@p2 (E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes the -Os breaks with gcc 4.5 bug. rdtsc_barrier needs to be
force inlined, otherwise user space will jump into kernel space and
kill init.
This also addresses http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44129
I believe.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100618210859.GA10913@basil.fritz.box>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
This patch uses "ENABLE_ON_INIT" flag on the emif clock nodes
to avoid the emif clk getting cut as part of reset un-used clock
routine which prevents boot.
Since "omap4xxx_clk_init()" calls "clk_enable_init_clocks()"
which increases the usecount on all ENABLE_ON_INIT clocks, it
prevents "omap2_clk_disable_unused()" from disabling the clock.
The real fix is to have driver for EMIF and do clock get/enable
as part of it. The EMIF driver is planned to be done HWMOD way
so till that available to keep omap3_defconfig booting on OMAP4430,
this patch is necessary.
(Will updated the auto-gen script for 44xx accordingly)
The fix was suggested by Paul Walmsley
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to my schematics, on Lite5200 board ethernet phy uses address
0 (all ADDR lines are pulled down). With this change I can talk to
onboard phy (LXT971) and correctly use autonegotiation.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When going to standby mode mpc code maps the whole soc5200 node
to access warious MBAR registers. However as of_iomap uses 'reg'
property of device node, only small part of MBAR is getting mapped.
Thus pm code gets oops when trying to access high parts of MBAR.
As a way to overcome this, make mpc52xx_pm_prepare() explicitly
map whole MBAR (0xc0000).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch probes for the Super IO chip and reserves the IO range when
found. It avoids enabling the IDE interface on the Avanti family, since
none has IDE. It enables the Enhanced Parallel Port v1.9 feature.
Signed-off-by: Morten H. Larsen <m-larsen@post6.tele.dk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
mpic_resume() on G5 macs blindly dereferences mpic->fixups, but
it may legitimately be NULL (as on PowerMac7,2). Add an explicit
check.
This fixes suspend-to-disk with one processor (maxcpus=1) for me.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When trying to flash a machine via the update_flash command, Anton received the
following error:
Restarting system.
FLASH: kernel bug...flash list header addr above 4GB
The code in question has a comment that the flash list should be in
the kernel data and therefore under 4GB:
/* NOTE: the "first" block list is a global var with no data
* blocks in the kernel data segment. We do this because
* we want to ensure this block_list addr is under 4GB.
*/
Unfortunately the Kconfig option is marked tristate which means the variable
may not be in the kernel data and could be above 4GB.
Instead of relying on the data segment being below 4GB, use the static
data buffer allocated by the kernel for use by rtas. Since we don't
use the header struct directly anymore, convert it to a simple pointer.
Reported-By: Anton Blanchard <anton@samba.org>
Signed-Off-By: Milton Miller <miltonm@bga.com
Tested-By: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Irq stacks provide an essential protection from stack overflows through
external interrupts, at the cost of two additionals stacks per CPU.
Enable them unconditionally to simplify the kernel build and prevent
people from accidentally disabling them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kexec_perpare_cpus_wait() iterates i through NR_CPUS to check
paca[i].kexec_state of each to make sure they have quiesced.
However now we have dynamic PACA allocation, paca[NR_CPUS] is not necessarily
valid and we overrun the array; spurious "cpu is not possible, ignoring"
errors result. This patch iterates for_each_online_cpu so stays
within the bounds of paca[] -- and every CPU is now 'possible'.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
On 5 May 2010 21:33, "Anton Blanchard" <anton@samba.org> wrote:
CONFIG_SYSFS_DEPRECATED can cause issues with newer distros and should not
be required for any distro in the last 3 or 4 years, so disable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was used in the dim distant past for adding initrds to images
for legacy iSeries, but it's not even used for that now that we
have initramfs. So remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing boot fails on some System p machines when using the kdump
crashkernel= boot option. The default kdump base address is 32MB, so if we
reserve 256MB for kdump then we reserve all of the RMO except the first 32MB.
We really want kdump to reserve some memory in the RMO and most of it
elsewhere but that will require more significant changes. For now we can shift
the default base address to 64MB when CONFIG_PPC64 and CONFIG_RELOCATABLE are
set. This isn't quite correct since what we really care about is the kdump
kernel is relocatable, but we already make the assumption that base kernel
and kdump kernel have the same CONFIG_RELOCATABLE setting, eg:
#ifndef CONFIG_RELOCATABLE
if (crashk_res.start != KDUMP_KERNELBASE)
printk("Crash kernel location must be 0x%x\n",
KDUMP_KERNELBASE);
...
RTAS is instantiated towards the top of our RMO, so if we were to go any
higher we risk not having enough RMO memory for the kdump kernel on boxes
with a 128MB RMO.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CONFIG_HIGHPTE doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PMU is not tested and enabled on MMP architecture at this moment,
the device IRQ number, IRQ_PMU depends on ARCH_PXA. Build PMU only
for ARCH_PXA.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since commit a48c24a696, the
camera is not working anymore.
After the v4l2 migration, the mt9m111 camera board
information was not passed to the i2c layer anymore, but
stored for future use of v4l2 (through soc_camera).
Because mioa701_i2c_devices[] was tagged as "__initdata",
and because after the v4l2 migration, the new structure
"iclink" references it, the mt9m111 driver is not probed
anymore, as part of "iclink" is not valid (discarded after
kernel init).
Although there is not compilation error, nor runtime oops,
this patch restores a working camera on the mioa701 board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch fixes flash layout to it's final version. Also, I fixed the
authorship information of this file as it's been totally reworked since Ken
released his last version.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
gpio must be int, not u16, otherwise -1 isn't recognised
by gpio_is_valid().
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
subtree_max_end that was recently added to struct memtype was not getting
properly initialized resulting in
WARNING: kmemcheck: Caught 64-bit read from uninitialized memory
in memtype_rb_augment_cb()
reported here
https://bugzilla.kernel.org/show_bug.cgi?id=16092
This change fixes the problem.
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <1276217101-11515-1-git-send-email-venki@google.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since
d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009.
Reported-by: Yannick <yannick.roehlly@free.fr>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently UML cannot stomach callee reg-saving trickery
introduced with d61931d89b
(x86: Add optimized popcnt variants) and oopses during boot:
http://marc.info/?l=linux-kernel&m=127522065202435&w=2
Redirect arch_hweight.h include from the x86 portion to the generic
arch_hweight.h which is a fallback to the software hweight routines.
LKML-Reference: <201005271944.09541.toralf.foerster@gmx.de>
Signed-off-by: Borislav Petkov <bp@alien8.de>
LKML-Reference: <4C0F4B00.4090307@panasas.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Catch missing conversion to the register structure "glove box" scheme.
Found by gcc 4.6's new warnings.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100610111040.F1781B1A2B@basil.firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: read apic->irr with ioapic lock held
KVM: ia64: Add missing spin_unlock in kvm_arch_hardware_enable()
KVM: Fix order passed to iommu_unmap
KVM: MMU: Remove user access when allowing kernel access to gpte.w=0 page
KVM: MMU: invalidate and flush on spte small->large page size change
KVM: SVM: Implement workaround for Erratum 383
KVM: SVM: Handle MCEs early in the vmexit process
KVM: powerpc: fix init/exit annotation
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix null pointer deref with SEND_SIG_FORCED
perf: Fix signed comparison in perf_adjust_period()
powerpc/oprofile: fix potential buffer overrun in op_model_cell.c
perf symbols: Set the DSO long name when using symbol_conf.vmlinux_name
Saving platform non-volatile state may be required for suspend to RAM as
well as hibernation. Move it to more generic code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6164/1: Add kto and kfrom to input operands list.
ARM: 6166/1: Proper prefetch abort handling on pre-ARMv6
ARM: 6165/1: trap overflows on highmem pages from kmap_atomic when debugging
ARM: 6152/1: ux500 make it possible to disable localtimers
[ARM] pxa/spitz: Correctly register WM8750
[ARM] pxa/palmtc: storage class should be before const qualifier
ARM: 6146/1: sa1111: Prevent deadlock in resume path
ARM: 6145/1: ux500 MTU clockrate correction
ARM: 6144/1: TCM memory bug freeing bug
ARM: VFP: Fix vfp_put_double() for d16-d31
Checking to se if the IO daisy chain is enabled should be checking the
PM_WKEN register, not the PM_WKST register. Reading PM_WKST tells us
if an event occurred, not whether or not it is enabled.
Apparently, we've been lucky until now in that a pending event has not
been there during enable. However, on 3630/Zoom3, I noticed because
of the WARN that this timeout was always happening.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avi Kivity