When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.
When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.
This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the hypervisor diagnose 0x26c
('Access Certain System Information').
It passes a request buffer and a subfunction code, and receives
a response buffer and a return code.
Also add the scaffolding for the 'MAC Services' subfunction.
It may be used by network devices to obtain a hypervisor-managed
MAC address.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's two spots in qeth_send_packet() where we don't accurately
account for transmitted packing buffers in qeth's performance
statistics:
1) when flushing the current buffer due to insufficient size,
and the next buffer is not EMPTY, we need to account for that
flushed buffer.
2) when synchronizing with the TX completion code, we reset
flush_count and thus forget to account for any previously
flushed buffers.
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add ipa return codes for Bridgeport (HiperSockets and OSA) according to
system level design.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a bad thing not to handle errors when updating asoc. The memory
allocation failure in any of the functions called in sctp_assoc_update()
would cause sctp to work unexpectedly.
This patch is to fix it by aborting the asoc and reporting the error when
any of these functions fails.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_cork is used to decide if it should uncork asoc outq after processing
some cmds, and it is set when replying or sending msgs. local_cork should
always have the same value with current asoc q->cork in some way.
The thing is when changing to a new asoc by cmd SET_ASOC, local_cork may
not be consistent with the current asoc any more. The cmd seqs can be:
SCTP_CMD_UPDATE_ASSOC (asoc)
SCTP_CMD_REPLY (asoc)
SCTP_CMD_SET_ASOC (new_asoc)
SCTP_CMD_DELETE_TCB (new_asoc)
SCTP_CMD_SET_ASOC (asoc)
SCTP_CMD_REPLY (asoc)
The 1st REPLY makes OLD asoc q->cork and local_cork both are 1, and the cmd
DELETE_TCB clears NEW asoc q->cork and local_cork. After asoc goes back to
OLD asoc, q->cork is still 1 while local_cork is 0. The 2nd REPLY will not
set local_cork because q->cork is already set and it can't be uncorked and
sent out because of this.
To keep local_cork consistent with the current asoc q->cork, this patch is
to uncork the old asoc if local_cork is set before changing to the new one.
Note that the above cmd seqs will be used in the next patch when updating
asoc and handling errors in it.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch "call inet_add_protocol after register_pernet_subsys in dccp_v4_init"
fixed a null pointer dereference issue for dccp_ipv4 module.
The same fix is needed for dccp_ipv6 module.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now dccp_ipv4 works as a kernel module. During loading this module, if
one dccp packet is being recieved after inet_add_protocol but before
register_pernet_subsys in which v4_ctl_sk is initialized, a null pointer
dereference may be triggered because of init_net.dccp.v4_ctl_sk is 0x0.
Jianlin found this issue when the following call trace occurred:
[ 171.950177] BUG: unable to handle kernel NULL pointer dereference at 0000000000000110
[ 171.951007] IP: [<ffffffffc0558364>] dccp_v4_ctl_send_reset+0xc4/0x220 [dccp_ipv4]
[...]
[ 171.984629] Call Trace:
[ 171.984859] <IRQ>
[ 171.985061]
[ 171.985213] [<ffffffffc0559a53>] dccp_v4_rcv+0x383/0x3f9 [dccp_ipv4]
[ 171.985711] [<ffffffff815ca054>] ip_local_deliver_finish+0xb4/0x1f0
[ 171.986309] [<ffffffff815ca339>] ip_local_deliver+0x59/0xd0
[ 171.986852] [<ffffffff810cd7a4>] ? update_curr+0x104/0x190
[ 171.986956] [<ffffffff815c9cda>] ip_rcv_finish+0x8a/0x350
[ 171.986956] [<ffffffff815ca666>] ip_rcv+0x2b6/0x410
[ 171.986956] [<ffffffff810c83b4>] ? task_cputime+0x44/0x80
[ 171.986956] [<ffffffff81586f22>] __netif_receive_skb_core+0x572/0x7c0
[ 171.986956] [<ffffffff810d2c51>] ? trigger_load_balance+0x61/0x1e0
[ 171.986956] [<ffffffff81587188>] __netif_receive_skb+0x18/0x60
[ 171.986956] [<ffffffff8158841e>] process_backlog+0xae/0x180
[ 171.986956] [<ffffffff8158799d>] net_rx_action+0x16d/0x380
[ 171.986956] [<ffffffff81090b7f>] __do_softirq+0xef/0x280
[ 171.986956] [<ffffffff816b6a1c>] call_softirq+0x1c/0x30
This patch is to move inet_add_protocol after register_pernet_subsys in
dccp_v4_init, so that v4_ctl_sk is initialized before any incoming dccp
packets are processed.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With -Wformat-truncation, gcc throws the following warning.
Fix this by increasing the size of devname to accommodate 15 character
netdev interface name and description.
Remove length format precision for %s. We can fit entire name.
Also increment the version.
drivers/net/ethernet/cisco/enic/enic_main.c: In function ‘enic_open’:
drivers/net/ethernet/cisco/enic/enic_main.c:1740:15: warning: ‘%u’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 12 [-Wformat-truncation=]
"%.11s-rx-%u", netdev->name, i);
^~
drivers/net/ethernet/cisco/enic/enic_main.c:1740:5: note: directive argument in the range [0, 16]
"%.11s-rx-%u", netdev->name, i);
^~~~~~~~~~~~~
drivers/net/ethernet/cisco/enic/enic_main.c:1738:4: note: ‘snprintf’ output between 6 and 18 bytes into a destination of size 16
snprintf(enic->msix[intr].devname,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(enic->msix[intr].devname),
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%.11s-rx-%u", netdev->name, i);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the IP that prevents us from enabling TSO for IPv6.
Before patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
882512708 bytes received in 00:14 (56.11 MiB/s)
After patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
1203326784 bytes received in 00:12 (94.52 MiB/s)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ibmvnic driver is not in the VNIC_OPEN state, return from
ibmvnic_resume callback. If we are not in the VNIC_OPEN state, interrupts
may not be initialized and directly calling the interrupt handler will
cause a crash.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide link partner advertising information.
Removed testing for gigabit modes, which is useless for a fast ethernet phy.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin says:
====================
net-next: mediatek: various performance improvements
During development we mainly ran testing using iperf doing 1500 byte
tcp frames. It was pointed out recently, that the driver does not perform
very well when using 512 byte udp frames. The biggest problem was that
RPS was not working as no rx queue was being set. fixing this more than
doubled the throughput. Additionally the IRQ mask register is now locked
independently for RX and TX. RX IRQ aggregation is also added. With all
these patches applied we can almost triple the throughput.
While at it we also add PHY status change reporting for GMACs connecting
directly to a PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_rps_cpu() function will not do any RPS on the data flow when no
queue is setup and always use the current cpu where the IRQ was handled
to also handle the backlog. As we only have one physical queue we always
set this to 0 unconditionally.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally the driver only utilised the new QDMA engine. The current code
still assumes this is the case when locking the IRQ mask register. Since
RX now runs on the old style PDMA engine we can add a second lock. This
patch reduces the IRQ latency as the TX and RX path no longer need to wait
on each other under heavy load.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDMA engine used for RX allows IRQ aggregation. The patch sets up the
corresponding registers to aggregate 4 IRQs into one. Using aggregation
reduces the load on the core handling to a quarter thus reducing IRQ
latency and increasing RX performance by around 10%.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PHY status changes are only printed for DSA ports. This patch
adds code to also print status changes for non-fixed links.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Schiffer says:
====================
vxlan: cleanup and IPv6 link-local support
Running VXLANs over IPv6 link-local addresses allows to use them as a
drop-in replacement for VLANs, avoiding to allocate additional outer IP
addresses to run the VXLAN over.
Since v1, I have added a lot more consistency checks to the address
configuration, making sure address families and scopes match. To simplify
the implementation, I also did some general refactoring of the
configuration handling in the new first patch of the series.
The second patch is more cleanup; is slightly touches OVS code, so that
list is in CC this time, too.
As in v1, the last two patches actually make VXLAN over IPv6 link-local
work, and allow multiple VXLANs with the same VNI and port, as long as
link-local addresses on different interfaces are used. As suggested, I now
store in the flags field if the VXLAN uses link-local addresses or not.
v3 removes log messages as suggested by Roopa Prabhu (as it is very unusual
for errors in netlink requests to be printed to the kernel log.) The commit
message of patch 5 has been extended to add a note about IPv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As link-local addresses are only valid for a single interface, we can allow
to use the same VNI for multiple independent VXLANs, as long as the used
interfaces are distinct. This way, VXLANs can always be used as a drop-in
replacement for VLANs with greater ID space.
This also extends VNI lookup to respect the ifindex when link-local IPv6
addresses are used, so using the same VNI on multiple interfaces can
actually work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VXLAN is run over link-local IPv6 addresses, it is necessary to store
the ifindex in the FDB entries. Otherwise, the used interface is undefined
and unicast communication will most likely fail.
Support for link-local IPv4 addresses should be possible as well, but as
the semantics aren't as well defined as for IPv6, and there doesn't seem to
be much interest in having the support, it's not implemented for now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Multicast addresses are never valid as local address
* Link-local IPv6 unicast addresses may only be used as remote when the
local address is link-local as well
* Don't allow link-local IPv6 local/remote addresses without interface
We also store in the flags field if link-local addresses are used for the
follow-up patches that actually make VXLAN over link-local IPv6 work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address families of source and destination addresses must match, and
changelink operations can't change the address family.
In addition, always use the VXLAN_F_IPV6 to check if a VXLAN device uses
IPv4 or IPv6.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to keep the flags twice in vxlan_dev and
vxlan_config.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxlan_dev_configure function was mixing validation and application of
the vxlan configuration; this could easily lead to bugs with the changelink
operation, as it was hard to see if the function wcould return an error
after parts of the configuration had already been applied.
This commit splits validation and application out of vxlan_dev_configure as
separate functions to make it clearer where error returns are allowed and
where the vxlan_dev or net_device may be configured. Log messages in these
functions are removed, as it is generally unexpected to find error output
for netlink requests in the kernel log. Userspace should be able to handle
errors based on the error codes returned via netlink just fine.
In addition, some validation and initialization is moved to vxlan_validate
and vxlan_setup respectively to improve grouping of similar settings.
Finally, this also fixes two actual bugs:
* if set, conf->mtu would overwrite dev->mtu in each changelink operation,
reverting other changes of dev->mtu
* the "if (!conf->dst_port)" branch would never be run, as conf->dst_port
was set in vxlan_setup before. This caused VXLAN-GPE to use the same
default port as other VXLAN sockets instead of the intended IANA-assigned
4790.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
yuan linyu says:
====================
net: more skb_put_[data:zero] related work
yuan linyu (3):
net: introduce __skb_put_[zero, data, u8]
net: replace more place to skb_put_[data:zero]
net: manual clean code which call skb_put_[data:zero]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the remaining shift macro in favor of calculating at compile time
its value from the more descriptive mask, which gives us a better
representation of the register layout.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: Global 2 cosmetics
Similarly to what has been done for the Port and Global 1 registers,
this patch series prefixes and documents the macros of Global 2.
It brings no functional changes except for 1/10 which fixes the IRL init
for 88E6390 family.
Changes in v2: make *_g2_irl_init_all static inline without
NET_DSA_MV88E6XXX_GLOBAL2 and compile test with and without the symbol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the remaining Global 2 registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.
Prefix and document that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Switch MAC registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 EEPROM registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Cross-chip Port VLAN registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 MGMT registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Device Mapping macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.
The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.
Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)
Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.
This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.
This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.
A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Icenowy Zheng says:
====================
net-next: stmmac: dwmac-sun8i: add support for V3s
Allwinner V3s features an EMAC like the on in H3, but without external MII
interfaces, so being not able really to use RMII/RGMII.
And it has a different default value of syscon (0x38000 instead of 0x58000
on H3), which shows a problem that the EMAC clock freq should be 24MHz.
(Both H3 and V3s SoCs doesn't have extra xtal input for EPHY, and the
main xtal is 24MHz. The default value of H3 is set to 24MHz, but the V3s
default value is set to 25MHz).
First two patches are device tree binding patches, the third forces
the frequency to 24MHz and the fourth really add the V3s support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has an Ethernet MAC and an internal PHY like the ones
in H3 SoC, however the MAC has no external *MII interfaces available at
GPIOs, thus only MII connection to internal PHY is supported.
Add this variant of EMAC to dwmac-sun8i driver.
The default value of the syscon EMAC-related register seems to have
changed from H3, but it seems to be a harmless change.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY control part of the EMAC syscon register has a bit called
CLK_SEL. On the datasheet it says that if it's 0 the EPHY clock is 25MHz
and if it's 1 the clock is 24MHz.
However, according to the datasheets, no Allwinner SoC with EPHY has any
extra xtal input pins for the EPHY, and the system xtal is 24MHz.
That means the EPHY is not possible to get a 25MHz xtal input, and thus
the frequency can only be 24MHz.
It doesn't matter on H3 as the default value of H3 is 24MHz, however on
V3s the default value is wrongly set to 25MHz, which prevented the EPHY
from working properly.
Force the EPHY clock frequency to 24MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has a syscon like the one in H3.
Add its compatible string.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has a Ethernet MAC like the one in Allwinner H3, but
have no external MII capability. That means that it can only use the
EPHY and cannot do Gbps transmission.
Add binding for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates says:
====================
net: Introduction of the tc tests
Apologies for sending this as one big patch. I've been sitting on this a little
too long, but it's ready and I wanted to get it out.
There are a limited number of tests to start - I plan to add more on a regular
basis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the beginnings of a testsuite for tc functionality in the kernel.
These are a series of unit tests that use the tc executable and verify
the success of those commands by checking both the exit codes and the
output from tc's 'show' operation.
To run the tests:
# cd tools/testing/selftests/tc-testing
# sudo ./tdc.py
You can specify the tc executable to use with the -p argument on the command
line or editing the 'TC' variable in tdc_config.py. Refer to the README for
full details on how to run.
The initial complement of test cases are limited mostly to tc actions. Test
cases are most welcome; see the creating-testcases subdirectory for help
in creating them.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed*: RDMA and infrastructure for iWARP
This series focuses on RDMA in general with emphasis on required changes
toward adding iWARP support. The vast majority of the changes introduced
are in qed/qede, with a couple of small changes to qedr
[mentioned below].
The infrastructure changes:
- Patch #1 adds the ability to pass PBL memory externally for a newly
created chain.
- Patches #4, #5 rename qede_roce.[ch] into qede_rdma.[ch] + change
prefixes from _roce_ to _rdma_, as the API between qede and qedr is
agnostic to the variant of the RDMA protocol used. These patches also
touch qedr [basically to align it with the renaming, nothing more].
- Patch #7 replaces the current SPQ async mechanism into serving
registered callbacks [before adding iWARP which would add another client
in need of this sort of functionallity].
The non-infrastrucutre changes:
- Patches #2, #3 contain DCB-related changes to better align RDMA with
configured DCB.
- Patch #6 contains a minor [mostly theoretical fix] to release flow.
Changes from previous versions
------------------------------
- V4: This is actually a repost of V3 due to some confusion regarding
the sent cover-letter
- V3: Add commit log message in #4 indicating change in header inclusion
- V2: Add several inclusion into qede_rdma.h to have proper declarations
of all variable types used in it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever firmware indicates that there's an async indication it needs
to handle, there's a switch-case where the right functionality is called
based on function's personality and information.
Before iWARP is added [as yet another client], switch over the SPQ into
a callback-registered mechanism, allowing registration of the relevant
event-processing logic based on the function's personality. This allows
us to tidy the code by removing protocol-specifics from a common file.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver needs to wait for all resources to return from FW before it can send
the FUNC_CLOSE ramrod.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann