The BCM2711, supported by ARCH_BCM2835, also has a controller by the
brcmstb driver so let's allow it to be compiled on that platform.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the slave eeprom has a "firmware-name" in devicetree, then pre-load
the data in the eeprom with this file. Otherwise we init the eeprom with
0xFF.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Björn Ardö <bjorn.ardo@axis.com>
[wsa: some cosmetic changes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
it will print an error message by itself when platform_get_irq()
goes wrong. so don't need dev_err() in here again.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds I2C bus support for the Camera Control Interface
(CCI) I2C controller found on the Qualcomm SoC processors. This I2C
controller supports two masters and they are registered to the core.
CCI versions supported in the driver are msm8916, msm8996 and sdm845.
This is a rework of the patch posted by Vinod:
https://patchwork.kernel.org/patch/10569961/
With additional fixes + most of the comments addressed.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[wsa: removed err msg after platform_get_irq]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added support for I2C slave functionality
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for High Speed Mode too.
The value for the parameters tSYMBOL and tLOW is taken from DesignWare
DW_apb_i2c Databook v2.01a, section 3.15.4.6. The calculation should
assume higher bus load since it gives slower timing parameter.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for Fast Mode Plus.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures. Use the existing GPIO_LOOKUP() helper
macro instead, to relax a dependency on the gpiod_lookup structure's
member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When I wanted to print the chosen values to debug output, I concluded
that a helper function to parse one timing would be helpful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has:
- using defines for bus speeds to avoid mistakes in hardcoded values;
lots of small driver updates because of that. Thanks, Andy!
- API change: i2c_setup_smbus_alert() was renamed to
i2c_new_smbus_alert_device() and returns ERRPTR now. All in-tree
users have been converted
- in the core, a rare race condition when deleting the cdev has been
fixed. Thanks, Kevin!
- lots of driver updates. Thanks, everyone!
I also want to mention: The amount of review and testing tags given
was quite high this time. Thank you to these people, too. I hope we
can keep it like this!"
* 'i2c/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: rcar: clean up after refactoring i2c_timings
macintosh: convert to i2c_new_scanned_device
i2c: drivers: Use generic definitions for bus frequencies
i2c: algo: Use generic definitions for bus frequencies
i2c: stm32f7: switch to I²C generic property parsing
i2c: rcar: Consolidate timings calls in rcar_i2c_clock_calculate()
i2c: core: Allow override timing properties with 0
i2c: core: Provide generic definitions for bus frequencies
i2c: mxs: Use dma_request_chan() instead dma_request_slave_channel()
i2c: imx: remove duplicate print after platform_get_irq()
i2c: designware: Fix spelling typos in the comments
i2c: designware: Discard i2c_dw_read_comp_param() function
i2c: designware: Detect the FIFO size in the common code
i2c: dev: Fix the race between the release of i2c_dev and cdev
i2c: qcom-geni: Drop of_platform.h include
i2c: qcom-geni: Grow a dev pointer to simplify code
i2c: qcom-geni: Let firmware specify irq trigger flags
i2c: stm32f7: do not backup read-only PECR register
i2c: smbus: remove outdated references to irq level triggers
i2c: convert SMBus alert setup function to return an ERRPTR
...
The pointer is not really needed anymore since we have the timings
struct available in the function itself now. Remove the pointer and
access the struct directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform 22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nvidia card may come with a "phantom" UCSI device, and its driver gets
stuck in probe routine, prevents any system PM operations like suspend.
There's an unaccounted case that the target time can equal to jiffies in
gpu_i2c_check_status(), let's solve that by using readl_poll_timeout()
instead of jiffies comparison functions.
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ajay Gupta <ajayg@nvidia.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic definitions for bus frequencies, let's use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions: i2c_parse_fw_timings().
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move i2c_parse_fw_timings() to rcar_i2c_clock_calculate() to consolidate
timings calls in one place.
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some drivers may allow to override properties with 0 value when defaults
are not in use, thus, replace memset() with corresponding per property
update.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are few maximum bus frequencies being used in the I²C core code.
Provide generic definitions for bus frequencies and use them in the core.
The drivers may use predefined constants where it is appropriate.
Some of them are already using these under slightly different names.
We will convert them later to use newly introduced defines.
Note, the name of modes are chosen to follow well established naming
scheme [1].
These definitions will also help to avoid typos in the numbers that
may lead to subtle errors.
[1]: https://en.wikipedia.org/wiki/I%C2%B2C#Differences_between_modes
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver forgets to disable and unprepare clk when remove.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We don't need dev_err() message because when something goes wrong,
platform_get_irq() has print an error message itself, so we should
remove duplicate dev_err().
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix spelling typos in the comments with help of `codespell`.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no code left in the kernel which would be using the function.
So just remove it.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The problem with detecting the FIFO depth in the platform driver
is that in order to implement this we have to access the controller
IC_COMP_PARAM_1 register. Currently it's done before the
i2c_dw_set_reg_access() method execution, which is errors prone since
the method determines the registers endianness and access mode and we
can't use dw_readl/dw_writel accessors before this information is
retrieved. We also can't move the i2c_dw_set_reg_access() function
invocation to after the master/slave probe functions call (when endianness
and access mode are determined), since the FIFO depth information is used
by them for initializations. So in order to fix the problem we have no
choice but to move the FIFO size detection methods to the common code and
call it at the probe stage.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The struct cdev is embedded in the struct i2c_dev. In the current code,
we would free the i2c_dev struct directly in put_i2c_dev(), but the
cdev is manged by a kobject, and the release of it is not predictable.
So it is very possible that the i2c_dev is freed before the cdev is
entirely released. We can easily get the following call trace with
CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 19 PID: 1 at lib/debugobjects.c:325 debug_print_object+0xb0/0xf0
Modules linked in:
CPU: 19 PID: 1 Comm: swapper/0 Tainted: G W 5.2.20-yocto-standard+ #120
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 80c00089 (Nzcv daIf +PAN +UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff00001292f7d0
x29: ffff00001292f7d0 x28: ffff800b82151788
x27: 0000000000000001 x26: ffff800b892c0000
x25: ffff0000124a2558 x24: 0000000000000000
x23: ffff00001107a1d8 x22: ffff0000116b5088
x21: ffff800bdc6afca8 x20: ffff000012471ae8
x19: ffff00001168f2c8 x18: 0000000000000010
x17: 00000000fd6f304b x16: 00000000ee79de43
x15: ffff800bc0e80568 x14: 79616c6564203a74
x13: 6e6968207473696c x12: 5f72656d6974203a
x11: ffff0000113f0018 x10: 0000000000000000
x9 : 000000000000001f x8 : 0000000000000000
x7 : ffff0000101294cc x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 00000000ffffffff x2 : 0000000000000000
x1 : 387fc15c8ec0f200 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
__debug_check_no_obj_freed+0x19c/0x228
debug_check_no_obj_freed+0x1c/0x28
kfree+0x250/0x440
put_i2c_dev+0x68/0x78
i2cdev_detach_adapter+0x60/0xc8
i2cdev_notifier_call+0x3c/0x70
notifier_call_chain+0x8c/0xe8
blocking_notifier_call_chain+0x64/0x88
device_del+0x74/0x380
device_unregister+0x54/0x78
i2c_del_adapter+0x278/0x2d0
unittest_i2c_bus_remove+0x3c/0x80
platform_drv_remove+0x30/0x50
device_release_driver_internal+0xf4/0x1c0
driver_detach+0x58/0xa0
bus_remove_driver+0x84/0xd8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
of_unittest_overlay+0x8d4/0xbe0
of_unittest+0xae8/0xb3c
do_one_initcall+0xac/0x450
do_initcall_level+0x208/0x224
kernel_init_freeable+0x2d8/0x36c
kernel_init+0x18/0x108
ret_from_fork+0x10/0x1c
irq event stamp: 3934661
hardirqs last enabled at (3934661): [<ffff00001009fa04>] debug_exception_exit+0x4c/0x58
hardirqs last disabled at (3934660): [<ffff00001009fb14>] debug_exception_enter+0xa4/0xe0
softirqs last enabled at (3934654): [<ffff000010081d94>] __do_softirq+0x46c/0x628
softirqs last disabled at (3934649): [<ffff0000100b4a1c>] irq_exit+0x104/0x118
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7f ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the i2c_dev,
and use the API provided by the commit 233ed09d7f to make sure that
the release of i2c_dev and cdev are in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver doesn't call any DT platform functions like of_platform_*().
Remove the include as it isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some lines are long here. Use a struct dev pointer to shorten lines and
simplify code. The clk_get() call can fail because of EPROBE_DEFER
problems too, so just remove the error print message because it isn't
useful. Finally, platform_get_irq() already prints an error so just
remove that error message.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to force IRQF_TRIGGER_HIGH here as the DT or ACPI tables
should take care of this for us. Just use 0 instead so that we use the
flags from the firmware. Also, remove specify dev_name() for the irq
name so that we can get better information in /proc/interrupts about
which device is generating interrupts.
Cc: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PECR register provides received packet computed PEC value.
It makes no sense restoring its value after a reset, and anyway,
as read-only register it cannot be restored.
Fixes: ea6dd25dee ("i2c: stm32f7: add PM_SLEEP suspend/resume support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_verify_client() can fail, so we need to put the device when that
happens.
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a GPIO we are trying to use is not available and we are deferring
the probe, don't output an error message.
This seems to have been the intent of commit 05c7477885
("i2c: gpio: Add support for named gpios in DT") but the error was
still output due to not checking the updated 'retdesc'.
Fixes: 05c7477885 ("i2c: gpio: Add support for named gpios in DT")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IRQ levels are now handled within the IRQ core. Remove the forgotten
references from the documentation.
Fixes: 9b9f2b8bc2 ("i2c: i2c-smbus: Use threaded irq for smbalert")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Only few drivers use this call, so drivers and I2C core are converted at
once with this patch. By simply using i2c_new_client_device() instead of
i2c_new_device(), we easily can return an ERRPTR for this function as
well. To make out of tree users aware that something changed, the
function is renamed to i2c_new_smbus_alert_device().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a new stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Defer the initial enabling of the Fast Mode Plus bits after the
stm32f7_i2c_setup_timing call in probe function in order to avoid
enabling them if speed is downgraded.
Clear & restore the Fast Mode Plus bits in the suspend/resume
handlers of the driver.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HDMI blocks in the BCM2771 have an i2c controller to retrieve the
EDID. This block is split into two parts, the BSC and the AUTO_I2C,
lying in two separate register areas.
The AUTO_I2C block has a mailbox-like interface and will take away the
BSC control from the CPU if enabled. However, the BSC is the actually
the same controller than the one supported by the brcmstb driver, and
the AUTO_I2C doesn't really bring any immediate benefit.
Let's use the BSC then, but let's also tie the AUTO_I2C registers with a
separate compatible so that we can enable AUTO_I2C if needed in the
future.
The AUTO_I2C is enabled by default at boot though, so we first need to
release the BSC from the AUTO_I2C control.
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a new API devm_platform_ioremap_resource() to simplify code.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Tested-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Function i2c_dw_pci_remove() -> pci_free_irq_vectors() ->
pci_disable_msi() -> free_msi_irqs() will throw a BUG_ON() for MSI
enabled device since the driver has not released the requested IRQ before
calling the pci_free_irq_vectors().
Here driver requests an IRQ using devm_request_irq() but automatic
release happens only after remove callback. Fix this by explicitly
freeing the IRQ before calling pci_free_irq_vectors().
Fixes: 21aa3983d6 ("i2c: designware-pci: Switch over to MSI interrupts")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Martin noticed that nct6775 driver does not load properly on his system
in v5.4+ kernels. The issue was bisected to commit b84398d6d7 ("i2c:
i801: Use iTCO version 6 in Cannon Lake PCH and beyond") but it is
likely not the culprit because the faulty code has been in the driver
already since commit 9424693035 ("i2c: i801: Create iTCO device on
newer Intel PCHs"). So more likely some commit that added PCI IDs of
recent chipsets made the driver to create the iTCO_wdt device on Martins
system.
The issue was debugged to be PCI configuration access to the PMC device
that is not present. This returns all 1's when read and this caused the
iTCO_wdt driver to accidentally request resourses used by nct6775.
It turns out that the SMI resource is only required for some ancient
systems, not the ones supported by this driver. For this reason do not
populate the SMI resource at all and drop all the related code. The
driver now always populates the main I/O resource and only in case of SPT
(Intel Sunrisepoint) compatible devices it adds another resource for the
NO_REBOOT bit. These two resources are of different types so
platform_get_resource() used by the iTCO_wdt driver continues to find
the both resources at index 0.
Link: https://lore.kernel.org/linux-hwmon/CAM1AHpQ4196tyD=HhBu-2donSsuogabkfP03v1YF26Q7_BgvgA@mail.gmail.com/
Fixes: 9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
[wsa: complete fix needs all of http://patchwork.ozlabs.org/project/linux-i2c/list/?series=160959&state=*]
Reported-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The comment had some flaws which are now fixed:
- the prefix is 'MAC' not 'AAPL'
- no kernel coding style and too short length
- 'we do' instead of 'we to'
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the i2c-stm32f7 controller to become a wakeup-source
of the system. In such case, when a slave is registered to the
I2C controller, receiving a I2C message targeting that registered
slave address wakes up the suspended system.
In order to be able to wake-up, the I2C controller DT node
must have the property wakeup-source defined and a slave
must be registered.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Maxime Ripard