The current CE4100 and 8250_pci code have both a limitation preventing the
registration and usage of CE4100's second UART. This patch changes the
platform code fixing up the UART port to work on a relative UART port
base address, as well as the 8250_pci code to make it register 2 UART ports
for CE4100 and pass the port index down to all consumers.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here I fixed from printk(KERN_ERR, ... to pr_err(... on tty_mutex.c
Signed-off-by: Sangho Yi <antiroot@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt8500_port is malloced in vt8500_serial_probe() and should be freed
before leaving from the error handling cases, otherwise it will
cause memory leak.
Fix it by move the allocation of vt8500_port after those test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows us to get rid of the ifdefs in 8250.c.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify divisor to select the nearest baud rate divider rather than the
lowest. It minimizes baud rate errors especially on low UART clock
frequencies.
For example, if uartclk is 33000000 and baud is 115200 the ratio is
about 17.9 The current code selects 17 (5% error) but should select 18
(0.5% error).
This 5% error in baud rate leads to garbage on receiving end, while 0.5%
doesn't.
The issue showed up when using the stock 8250 driver for
Synopsys DW UART. This was on a FPGA with ~12MHz UART clock.
When we enabled early serial, we saw garbage which was narrowed down
to the rounding error.
So the bug had been latent and it only showed up with such low clock rates.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver has the low_latency flag set and uses the schedule_flip()
function to initiate copying data to the line discipline, a workqueue is
scheduled in but never actually flushed. This is incorrect use of the
low_latency flag (driver should not support the low_latency flag, or use
the tty_flip_buffer_push() function instead). Make sure a warning is
reported to catch incorrect use of the low_latency flag.
This patch goes with: cee4ad1ed9
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So this is it. The big step why we did all the work over the past
kernel releases. Now everything is prepared, so nothing protects us
from doing that big step.
| | \ \ nnnn/^l | |
| | \ / / | |
| '-,.__ => \/ ,-` => | '-,.__
| O __.´´) ( .` | O __.´´)
~~~ ~~ `` ~~~ ~~
The buffers are now in the tty_port structure and we can start
teaching the buffer helpers (insert char/string, flip etc.) to use
tty_port instead of tty_struct all around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For that purpose we have to temporarily introduce a second tty back
pointer into tty_port. It is because serial layer, and maybe others,
still do not use tty_port_tty_set/get. So that we cannot set the
tty_port->tty to NULL at will now.
Yes, the fix would be to convert whole serial layer and all its users
to tty_port_tty_set/get. However we are in the process of removing the
need of tty in most of the call sites, so this would lead to a
duplicated work.
Instead we have now tty_port->itty (internal tty) which will be used
only in flush_to_ldisc. For that one it is ensured that itty is valid
wherever the work is run. IOW, the work is synchronously cancelled
before we set itty to NULL and also before hangup is processed.
After we need only tty_port and not tty_struct in most code, this
shall be changed to tty_port_tty_set/get and itty removed completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the move of tty buffers from tty_struct to tty_port, we will
need to switch all users of buf to tty->port->buf. There are many
functions where this is accessed directly in their code many times.
Cache the tty->buf pointer in such functions now and change only
single lines in each function in the next patch.
Not that it is convenient for the next patch, but the code is now also
more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are only TTY buffers specific. And the buffers will go to
tty_port in the next patches. So to remove the need to have both
tty_port and tty_struct at some places, let us move the flags to
tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some funtions we need only n_tty_data, so pass it down directly in
case tty is not needed there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atomic_write_lock is not n_tty specific, so move it up in the
tty_struct.
And since these are the last ones to move, remove also the comment
saying there are some ldisc' members. There are none now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the ring-buffers...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here we move bitmaps and use DECLARE_BITMAP to declare them in the new
structure. And instead of memset, we use bitmap_zero as it is more
appropriate.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here we start moving all the n_tty related bits from tty_struct to
the newly defined n_tty_data struct in n_tty proper.
In this patch primitive members and bits are moved. The rest will be
done per-partes in the next patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All n_tty related members from tty_struct will be moved here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a private member of n_tty. Stop accessing it. Instead, take is
as an argument.
This is needed to allow clean switch of the private members to a
separate private structure of n_tty.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* BUG_ON(!tty) in n_tty_set_termios -- it cannot be called with tty ==
NULL. It is called from two call sites. First, from n_tty_open where
we have a valid tty. Second, as ld->ops->set_termios from
tty_set_termios. But there we have a valid tty too.
* if (!tty) in n_tty_open -- why would the TTY layer call ldisc's
open with an invalid TTY? No it indeed does not. All call sites have
a tty and dereference that.
* BUG_ON(!tty->read_buf) in n_tty_read -- this used to be a valid
check. The ldisc handling was broken some time ago when I added the
check to ensure everything is OK. It still can catch the case, but
no later than we move the buffer to ldisc data. Then there will be
no read_buf in tty_struct, i.e. nothing to check for.
* if (!tty->read_buf) in n_tty_receive_buf -- this should never
happen. All callers of ldisc->ops->receive_ops should hold a
reference to an ldisc and close (which frees read_buf) cannot be
called until the reference is dropped.
* if (WARN_ON(!tty->read_buf)) in n_tty_read -- the same as in the
previous case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ldisc->open and close are called only once and cannot cross. So the
tests in open and close are superfluous. Remove them. (But leave sets
to NULL to ensure there is not a bug somewhere.)
And when the tests are gone, handle properly failures in open. We
leaked read_buf if allocation of echo_buf failed before. Now this is
not the case anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We reintroduced tty_ldisc_wait_idle in 100eeae2c5 (TTY: restore
tty_ldisc_wait_idle) and used in set_ldisc. Then we added it also to
the hangup path in 92f6fa09bd (TTY: ldisc, do not close until there
are readers). And we noted that there is one more path:
~ Before 65b770468e tty_ldisc_wait_idle was called also from
~ tty_ldisc_release. It is called from tty_release, so I don't think
~ we need to restore that one.
Well, I was wrong. There might still be holders of an ldisc
reference. Not from userspace, but drivers. If they take a reference
and a user closes the device immediately after that, we have a
problem. ldisc is halted and closed by TTY, but the driver still may
call some ldisc's operation and cause a crash.
So restore the tty_ldisc_wait_idle call also to the third location
where it was before 65b770468e (tty-ldisc: turn ldisc user count
into a proper refcount). Now we should be safe with respect to the
ldisc reference counting as all* tty_ldisc_close paths are safely
called with reference count of one.
* Not the one in tty_ldisc_setup's fail path. But that is called
before the first open finishes. So userspace does not see it yet.
Even thought the driver is given the TTY already via ->install, it
should not take a reference to the ldisc yet. If some driver is to
do this, we should put one tty_ldisc_wait_idle also in the setup.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There used to be a single tty_ldisc_ref_wait. But then, when a
big-tty-mutex (BTM) was introduced, it has to be tty_ldisc_ref +
tty_unlock + tty_ldisc_ref_wait + tty_lock. Later, BTM was removed
from that path and tty_ldisc_ref + tty_ldisc_ref_wait remained there.
But it makes no sense now. So leave there only tty_ldisc_ref_wait.
And when we have a reference to an ldisc, actually use it in the loop.
Otherwise it may be racy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have control over tty->driver_data in pty, we can just
kill the /dev/pts/ in pty code too. Namely, in ->shutdown hook of
tty. For pty, this is called only once, for whichever end is closed
last. But we don't care, both driver_data are the inode as it used to
be till now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The goal is to stop setting and using tty->driver_data in devpts code.
It should be used solely by the driver's code, pty in this case.
Now driver_data are managed only in the pty driver. devpts_pty_new is
switched to accept what we used to dig out of tty_struct, i.e. device
node number and index.
This also removes a note about driver_data being set outside of the
driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The goal is to stop setting and using tty->driver_data in devpts code.
It should be used solely by the driver's code, pty in this case.
For the cleanup of layering, we will need the inode created in
devpts_pty_new to be stored into slave's driver_data. So we convert
devpts_pty_new to return the inode or an ERR_PTR-encoded error in case
of failure.
The move of 'inode = new_inode(sb);' from declarators to the code is
only cosmetical, but it makes the code easier to read.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The goal is to stop setting and using tty->driver_data in devpts code.
It should be used solely by the driver's code, pty in this case.
First, here we remove TTY from devpts_get_tty and rename it to
devpts_get_priv. Note we do not remove type safety, we just shift the
[implicit] (void *) cast one layer up.
index was unused in devpts_get_tty, so remove that from the prototype
too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When low_latency flag is set the TTY receive flip buffer is copied to the
line discipline directly instead of using a work queue in the background.
Therefor only in case a workqueue is actually used for copying data to the
line discipline we'll have to flush the workqueue.
This prevents unnecessary spin lock/unlock on the workqueue spin lock that
can cause additional scheduling overhead on a PREEMPT_RT system. On a 200
MHz AT91SAM9261 processor setup this fixes about 100us of scheduling
overhead on the TTY read call.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tty and serial driver fixes for your 3.7-rc1 tree.
Again, the UABI header file fixes, and a number of build and runtime serial
driver bugfixes that solve problems people have been reporting (the staging
driver is a tty driver, hence the fixes coming in through this tree.)
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCBmVQACgkQMUfUDdst+ynEuwCfexOnEj0evTfXN32kqG50MglI
o/UAnixeFbfSrHtFOybIEKiHchG2QX9F
=LPFk
-----END PGP SIGNATURE-----
Merge tag 'tty-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are some tty and serial driver fixes for your 3.7-rc1 tree.
Again, the UABI header file fixes, and a number of build and runtime
serial driver bugfixes that solve problems people have been reporting
(the staging driver is a tty driver, hence the fixes coming in through
this tree.)
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
staging: dgrp: check return value of alloc_tty_driver
staging: dgrp: check for NULL pointer in (un)register_proc_table
serial/8250_hp300: Missing 8250 register interface conversion bits
UAPI: (Scripted) Disintegrate include/linux/hsi
tty: serial: sccnxp: Fix bug with unterminated platform_id list
staging: serial: dgrp: Add missing #include <linux/uaccess.h>
serial: sccnxp: Allows the driver to be compiled as a module
tty: Fix bogus "callbacks suppressed" messages
net, TTY: initialize tty->driver_data before usage
Pull sparc fixes from David Miller:
"Two sparc64 perf bug fixes and add a sysrq facility so I can diagnose
these kinds of problems more quickly in the future."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix bit twiddling in sparc_pmu_enable_event().
sparc64: Add global PMU register dumping via sysrq.
sparc64: Like x86 we should check current->mm during perf backtrace generation.
commit 2655a2c76f ("8250: use the 8250
register interface not the legacy one") forgot to fully switch one
instance of struct uart_port to struct uart_8250_port, causing the
following compile failure:
drivers/tty/serial/8250/8250_hp300.c: In function ‘hpdca_init_one’:
drivers/tty/serial/8250/8250_hp300.c:174: error: ‘uart’ undeclared (first use in this function)
drivers/tty/serial/8250/8250_hp300.c:174: error: (Each undeclared identifier is reported only once
drivers/tty/serial/8250/8250_hp300.c:174: error: for each function it appears in.)
This went unnoticed in -next, as CONFIG_HPDCA is not set to y by
allmodconfig.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Philip Blundell <philb@gnu.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This syncs up the tty-linus branch to the latest in Linus's tree to get all of
the UAPI stuff needed for the next set of patches to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was already pointed out how to fix these cases before the offending
patches were merged, but unsurprisingly, that didn't happen. As this
change is entirely superfluous to begin with, simply shut things up by
casting everything away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cleanups
Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
Add module event hooks for simplified debugging with gdb
Fixes
Fix kdb to stop paging with 'q' on bta and dmesg
Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
Allow kgdboc=kdb to setup kdb on the vga console
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uf0L
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQeBKDAAoJEFjIrFwIi8fJDpwH/3nPBH82pJVxdLPBnmJhWuJR
voSPP0m9i69w/mc7wHtiRwK4lRMAUidgS77iBZkIT2cY0/NYvOKKBlMUitkYJFlK
dTVqr9O4iQcuG2yQk8+mXxC6NLH1VKOnSIyhqRswrePoBKzoHi/x7Y462a+tbxa9
lGBHT9/SqeYXyItRfkdfmAXFZcqIJqLRXEwRMvbky1U3s2QGy7CdIQgra0zWF+t1
ashNpaEBpH9Jy60VSpQtMpx8hWxd0W2NirNu+nACtTE5/MeuiBvKlPdEPC/rUbdJ
c5j5VYLjSxPCheY0sajK6pxKgHdfiqmMRlutzMVj3Egwilb0LBxv1018gRFzBu8=
=/qCG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"This has four bug-fixes and one tiny feature that I forgot to put
initially in my tree due to oversight.
The feature is for kdump kernels to speed up the /proc/vmcore reading.
There is a ram_is_pfn helper function that the different platforms can
register for. We are now doing that.
The bug-fixes cover some embarrassing struct pv_cpu_ops variables
being set to NULL on Xen (but not baremetal). We had a similar issue
in the past with {write|read}_msr_safe and this fills the three
missing ones. The other bug-fix is to make the console output (hvc)
be capable of dealing with misbehaving backends and not fall flat on
its face. Lastly, a quirk for older XenBus implementations that came
with an ancient v3.4 hypervisor (so RHEL5 based) - reading of certain
non-existent attributes just hangs the guest during bootup - so we
take precaution of not doing that on such older installations.
Feature:
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not
used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console."
* tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pv-on-hvm kexec: add quirk for Xen 3.4 and shutdown watches.
xen/bootup: allow {read|write}_cr8 pvops call.
xen/bootup: allow read_tscp call for Xen PV guests.
xen pv-on-hvm: add pfn_is_ram helper for kdump
xen/hvc: handle backend CLOSED without CLOSING
It is possible to miss data when using the kdb pager. The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal. This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.
The pager will now look at the kdb_buffer string to see how many
characters are printed. It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.
This also means that the vt screen needs to set the kdb COLUMNS
variable.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
It is a common enough mistake for people to specify "kdb" when they
meant to type "kbd" that the kgdboc can just accept both since they
both mean the same thing anyway. Specifically it is for the case
where you want kdb to be active on your graphics console + keyboard
(where kbd was the original abbreviation for keyboard).
With this change kgdboc will now accept either to mean the same thing:
kgdboc=kbd
kgdboc=kdb
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
The build even tells you that this is a bad thing:
drivers/tty/serial/sccnxp: struct platform_device_id is 32 bytes. The
last of 8 is:
0x73 0x63 0x36 0x38 0x36 0x39 0x32 0x00 0x00 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x54 0x0c 0x01 0x00
0x00 0x00 0x00 0x00
FATAL: drivers/tty/serial/sccnxp: struct platform_device_id is not
terminated with a NULL entry!
So fix this problem up before someone oopses their box when loading the
driver, as this breaks the build.
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* When hotplugging PCI devices in a PV guest we can allocate Xen-SWIOTLB later.
* Cleanup Xen SWIOTLB.
* Support pages out grants from HVM domains in the backends.
* Support wild cards in xen-pciback.hide=(BDF) arguments.
* Update grant status updates with upstream hypervisor.
* Boot PV guests with more than 128GB.
* Cleanup Xen MMU code/add comments.
* Obtain XENVERS using a preferred method.
* Lay out generic changes to support Xen ARM.
* Allow privcmd ioctl for HVM (used to do only PV).
* Do v2 of mmap_batch for privcmd ioctls.
* If hypervisor saves the LED keyboard light - we will now instruct the kernel
about its state.
Fixes:
* More fixes to Xen PCI backend for various calls/FLR/etc.
* With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
* Fix up smatch warnings.
* Fix up various return values in privmcmd and mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQaY8qAAoJEFjIrFwIi8fJwPMH+gKngf4vSqrHjw+V2nsmeYaw
zrhRQrm3xV4BNR7yQHs+InDst/AJRAr0GjuReDK4BqDEzUfcFKvzalspdMGGqf+W
MUp+pMdN2S6649r/KMFfPCYcQvmIkFu8l76aClAqfA77SZRv1VL2Gn9eBxd82jS0
sWAUu5ichDSdfm/vAKXhdvhlKsK0hmihEbCM3+wRBoXEJX0kKbhEGn82smaLqkEt
uxWDJBT4nyYqbm6KVXQJ/WYCaWEmEImGSDb9J1WeqftGEn1Q55mpknvElkpNPE1b
Ifayqk50Kt43qnLk/AUrm8KFFlNKb73wTyAb0hVw7SQDcw1AcLa8ZdohLIZOl/4=
=prMY
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
- When hotplugging PCI devices in a PV guest we can allocate
Xen-SWIOTLB later.
- Cleanup Xen SWIOTLB.
- Support pages out grants from HVM domains in the backends.
- Support wild cards in xen-pciback.hide=(BDF) arguments.
- Update grant status updates with upstream hypervisor.
- Boot PV guests with more than 128GB.
- Cleanup Xen MMU code/add comments.
- Obtain XENVERS using a preferred method.
- Lay out generic changes to support Xen ARM.
- Allow privcmd ioctl for HVM (used to do only PV).
- Do v2 of mmap_batch for privcmd ioctls.
- If hypervisor saves the LED keyboard light - we will now instruct
the kernel about its state.
Fixes:
- More fixes to Xen PCI backend for various calls/FLR/etc.
- With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
- Fix up smatch warnings.
- Fix up various return values in privmcmd and mm."
* tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (48 commits)
xen/pciback: Restore the PCI config space after an FLR.
xen-pciback: properly clean up after calling pcistub_device_find()
xen/vga: add the xen EFI video mode support
xen/x86: retrieve keyboard shift status flags from hypervisor.
xen/gndev: Xen backend support for paged out grant targets V4.
xen-pciback: support wild cards in slot specifications
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
xen/arm: compile and run xenbus
xen: resynchronise grant table status codes with upstream
xen/privcmd: return -EFAULT on error
xen/privcmd: Fix mmap batch ioctl error status copy back.
xen/privcmd: add PRIVCMD_MMAPBATCH_V2 ioctl
xen/mm: return more precise error from xen_remap_domain_range()
xen/mmu: If the revector fails, don't attempt to revector anything else.
...
Pull vfs update from Al Viro:
- big one - consolidation of descriptor-related logics; almost all of
that is moved to fs/file.c
(BTW, I'm seriously tempted to rename the result to fd.c. As it is,
we have a situation when file_table.c is about handling of struct
file and file.c is about handling of descriptor tables; the reasons
are historical - file_table.c used to be about a static array of
struct file we used to have way back).
A lot of stray ends got cleaned up and converted to saner primitives,
disgusting mess in android/binder.c is still disgusting, but at least
doesn't poke so much in descriptor table guts anymore. A bunch of
relatively minor races got fixed in process, plus an ext4 struct file
leak.
- related thing - fget_light() partially unuglified; see fdget() in
there (and yes, it generates the code as good as we used to have).
- also related - bits of Cyrill's procfs stuff that got entangled into
that work; _not_ all of it, just the initial move to fs/proc/fd.c and
switch of fdinfo to seq_file.
- Alex's fs/coredump.c spiltoff - the same story, had been easier to
take that commit than mess with conflicts. The rest is a separate
pile, this was just a mechanical code movement.
- a few misc patches all over the place. Not all for this cycle,
there'll be more (and quite a few currently sit in akpm's tree)."
Fix up trivial conflicts in the android binder driver, and some fairly
simple conflicts due to two different changes to the sock_alloc_file()
interface ("take descriptor handling from sock_alloc_file() to callers"
vs "net: Providing protocol type via system.sockprotoname xattr of
/proc/PID/fd entries" adding a dentry name to the socket)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (72 commits)
MAX_LFS_FILESIZE should be a loff_t
compat: fs: Generic compat_sys_sendfile implementation
fs: push rcu_barrier() from deactivate_locked_super() to filesystems
btrfs: reada_extent doesn't need kref for refcount
coredump: move core dump functionality into its own file
coredump: prevent double-free on an error path in core dumper
usb/gadget: fix misannotations
fcntl: fix misannotations
ceph: don't abuse d_delete() on failure exits
hypfs: ->d_parent is never NULL or negative
vfs: delete surplus inode NULL check
switch simple cases of fget_light to fdget
new helpers: fdget()/fdput()
switch o2hb_region_dev_write() to fget_light()
proc_map_files_readdir(): don't bother with grabbing files
make get_file() return its argument
vhost_set_vring(): turn pollstart/pollstop into bool
switch prctl_set_mm_exe_file() to fget_light()
switch xfs_find_handle() to fget_light()
switch xfs_swapext() to fget_light()
...
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
These were submitted as bug fixes before v3.6 but not considered important
enough to be included in it. Some of them cross over to cleanup territory
as well, and aren't strictly bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bWnd
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM soc bug fixes from Olof Johansson:
"These were submitted as bug fixes before v3.6 but not considered
important enough to be included in it. Some of them cross over to
cleanup territory as well, and aren't strictly bugfixes."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: nomadik: remove NAND_NO_READRDY use
ARM: pxa: fix return value check in pxa2xx_drv_pcmcia_probe()
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
ARM: ep93xx: Move ts72xx.h out of include/mach
ARM: ep93xx: use __iomem pointers for MMIO
ARM: msm: Fix early debug uart mapping on some memory configs
ARM: msm: io: Change the default static iomappings to be shared
ARM: msm: io: Remove 7x30 iomap region from 7x00
ARM: msm: Remove call to missing FPGA init on 8660
ARM: OMAP4: wakeupgen: remove duplicate AUXCOREBOOT* read/write
ARM: OMAP4: wakeupgen: Fix the typo in AUXCOREBOOT register save
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
...
As we skipped the merge window for 3.6-rc1 for the tty tree, everything
is now settled down and working properly, so we are ready for 3.7-rc1.
Here's the patchset, it's big, but the large changes are removing a
firmware file and adding a staging tty driver (it depended on the tty
core changes, so it's going through this tree instead of the staging
tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp36oACgkQMUfUDdst+yk4WgCdEy13hot8fI2Lqnc7W0LKu7GX
4p8AoLTjzrXhLosxdijskDQ9X1OtjrxU
=S5Ng
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY changes from Greg Kroah-Hartman:
"As we skipped the merge window for 3.6-rc1 for the tty tree,
everything is now settled down and working properly, so we are ready
for 3.7-rc1. Here's the patchset, it's big, but the large changes are
removing a firmware file and adding a staging tty driver (it depended
on the tty core changes, so it's going through this tree instead of
the staging tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up more-or-less trivial conflicts in
- drivers/char/pcmcia/synclink_cs.c:
tty NULL dereference fix vs tty_port_cts_enabled() helper function
- drivers/staging/{Kconfig,Makefile}:
add-add conflict (dgrp driver added close to other staging drivers)
- drivers/staging/ipack/devices/ipoctal.c:
"split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"
* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
tty/serial: Add kgdb_nmi driver
tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
tty/serial/amba-pl011: Implement poll_init callback
tty/serial/core: Introduce poll_init callback
kdb: Turn KGDB_KDB=n stubs into static inlines
kdb: Implement disable_nmi command
kernel/debug: Mask KGDB NMI upon entry
serial: pl011: handle corruption at high clock speeds
serial: sccnxp: Make 'default' choice in switch last
serial: sccnxp: Remove mask termios caps for SW flow control
serial: sccnxp: Report actual baudrate back to core
serial: samsung: Add poll_get_char & poll_put_char
Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
Powerpc 8xx CPM_UART maxidl should not depend on fifo size
Powerpc 8xx CPM_UART too many interrupts
Powerpc 8xx CPM_UART desynchronisation
serial: set correct baud_base for EXSYS EX-41092 Dual 16950
serial: omap: fix the reciever line error case
8250: blacklist Winbond CIR port
8250_pnp: do pnp probe before legacy probe
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
iterates through the opened files in given descriptor table,
calling a supplied function; we stop once non-zero is returned.
Callback gets struct file *, descriptor number and const void *
argument passed to iterator. It is called with files->file_lock
held, so it is not allowed to block.
tty_io, netprio_cgroup and selinux flush_unauthorized_files()
converted to its use.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This special driver makes it possible to temporary use NMI debugger port
as a normal console by issuing 'nmi_console' command (assuming that the
port is attached to KGDB).
Unlike KDB's disable_nmi command, with this driver you are always able
to go back to the debugger using KGDB escape sequence ($3#33). This is
because this console driver processes the input in NMI context, and thus
is able to intercept the magic sequence.
Note that since the console interprets input and uses polling
communication methods, for things like PPP it is still better to fully
detach debugger port from the KGDB NMI (i.e. disable_nmi), and use raw
console.
Usually, to enter the debugger one have to type the magic sequence, so
initially the kernel will print the following prompt on the NMI debugger
console:
Type $3#33 to enter the debugger>
For convenience, there is a kgdb_fiq.knock kernel command line option,
when set to 0, this turns the special command to just a return key
press, so the kernel will be printing this:
Hit <return> to enter the debugger>
This is more convenient for long debugging sessions, although it makes
nmi_console feature somewhat useless.
And for the cases when NMI connected to a dedicated button, the knocking
can be disabled altogether by setting kgdb_fiq.knock to -1.
Suggested-by: Colin Cross <ccross@android.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to quiesce interrupts in the poll_get_char routine, otherwise,
if used with KGDB NMI debugger, we'll keep reentering the NMI.
Quiescing interrupts is pretty straightforward, except for TXIM
interrupt. The interrupt has "ready to transmit" meaning, so it's
almost always raised, and the only way to silence it is to mask it. But
that's OK, ops->start_tx will unmask it.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callback is used to initialize the hardware, nothing else should be
done, i.e. we should not request interrupts (but we can and do unmask
some of them, as they might be useful for NMI entry).
As a side-effect, the patch also fixes a division by zero[1] when booting
with kgdboc options specified (e.g. kgdboc=ttyAMA0,115200n8). The issue
happens because serial core calls set_termios callback, but the driver
doesn't know clock frequency, and thus cannot calculate proper baud rate
values.
[1]
WARNING: at drivers/tty/serial/serial_core.c:400 uart_get_baud_rate+0xe8/0x14c()
Modules linked in:
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c0020ae8>] (warn_slowpath_common+0x4c/0x64)
[<c0020ae8>] (warn_slowpath_common+0x4c/0x64) from [<c0020b1c>] (warn_slowpath_null+0x1c/0x24)
[<c0020b1c>] (warn_slowpath_null+0x1c/0x24) from [<c0185ed8>] (uart_get_baud_rate+0xe8/0x14c)
[<c0185ed8>] (uart_get_baud_rate+0xe8/0x14c) from [<c0187078>] (pl011_set_termios+0x48/0x278)
[<c0187078>] (pl011_set_termios+0x48/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
---[ end trace 7d41c9186f342c40 ]---
Division by zero in kernel.
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c014546c>] (Ldiv0+0x8/0x10)
[<c014546c>] (Ldiv0+0x8/0x10) from [<c0187098>] (pl011_set_termios+0x68/0x278)
[<c0187098>] (pl011_set_termios+0x68/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
Division by zero in kernel.
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c014546c>] (Ldiv0+0x8/0x10)
[<c014546c>] (Ldiv0+0x8/0x10) from [<c0183a98>] (uart_update_timeout+0x4c/0x5c)
[<c0183a98>] (uart_update_timeout+0x4c/0x5c) from [<c01870f8>] (pl011_set_termios+0xc8/0x278)
[<c01870f8>] (pl011_set_termios+0xc8/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was noticed that polling drivers (like KGDB) are not able to use
serial ports if the ports were not previously initialized via console.
I.e. when booting with console=ttyAMA0 kgdboc=ttyAMA0, everything works
fine, but with console=ttyFOO kgdboc=ttyAMA0, the kgdboc doesn't work.
This is because we don't initialize the hardware. Calling ->startup() is
not an option, because drivers request interrupts there, and drivers
fail to handle situations when tty isn't opened with interrupts enabled.
So, we have to implement a new callback (actually, tty_ops already have
a similar callback), which does everything needed to initialize just the
hardware.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.
Problem Observed/rootcause:
When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.
Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.
Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <matthias.locher@stericsson.com>
Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com>
Cc: stable <stable@vger.kernel.org>
Cc: Bibek Basu <bibek.basu@stericsson.com>
Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel will handle IXON/IXOFF/IXANY in software if the hardware
doesn't do it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch allows users to use KGDB over serial console on
board based on Samsung SOC. It has been tested on a board using
exynos5.
[dianders: changed poll to return NO_POLL_CHAR, which appears to
fix 'help' in kgdb; also updated commit message]
Signed-off-by: Julien Pichon <pichon.jln@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAXIDL is the timeout after which a receive buffer is closed when not full if
no more characters are received. We calculate it from the baudrate so that the
duration is always the same at standard rates: about 4ms. At 9600 bauds it gives
a timeout of 4 characters, which is the timeout on the 8250 UART.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
maxidl register was set to fifo size. There is no reason to set this
register to same value as fifo size. Setting it now to 0x10 by default
as in the UCC UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the fifo to only 1 byte generates one interrupt every 1ms at 9600 bauds.
This is too much. This patch reduces the threshold to speeds below 2400 bauds
like in the 8250 UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a desynchronisation problem with CPM UART driver on
Powerpc MPC8xx. The problem happens if data is received before the device
is open by the user application.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d6
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.
This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.
Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Drop the check for "up" being valid on suspend/resume callbacks.
It should be valid always. Get rid of the "pdata" check also as
serial_omap_get_context_loss_count() checks for it.
Tested on omap4 panda and 3630 based Beagle board.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_drvdata always retrun a valid value after probe succeed.
It also fixed smatch warnings:
drivers/tty/serial/imx.c:1376 serial_imx_suspend() warn: variable dereferenced before check 'sport' (see line 1372)
drivers/tty/serial/imx.c:1392 serial_imx_resume() warn: variable dereferenced before check 'sport' (see line 1388)
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The autoconfig prints messages while holding the
port's spinlock and that causes a deadlock when
using serial console.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We end up dropping the mutex twice on some errors. We don't want to do
that.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a serial driver is called post hangup with a second DCD event then we
will attempt to get the ldisc of NULL. Check we have a tty before trying to
do anything with it.
This is still only safe within the uart layer if the caller holds the
relevant uart locks. We could do with a version where the tty is passed for
more general use.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase vt8500_max_ports to 6 as the WM8505 as 6 available uarts.
Use devicetree port id as primary addressing for ports but allow
auto-allocation if id not specified.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Alan Cox <alan@linux.intel.com>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Alan says these are not production ready, and users should be told this,
so put the "(EXPERIMENTAL)" marking back in the Kconfig entry string.
Reported-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Cc: Kees Cook <keescook@chromium.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Explicitly format uids gids in audit messges in the initial user
namespace. This is safe because auditd is restrected to be in
the initial user namespace.
- Convert audit_sig_uid into a kuid_t.
- Enable building the audit code and user namespaces at the same time.
The net result is that the audit subsystem now uses kuid_t and kgid_t whenever
possible making it almost impossible to confuse a raw uid_t with a kuid_t
preventing bugs.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Always store audit loginuids in type kuid_t.
Print loginuids by converting them into uids in the appropriate user
namespace, and then printing the resulting uid.
Modify audit_get_loginuid to return a kuid_t.
Modify audit_set_loginuid to take a kuid_t.
Modify /proc/<pid>/loginuid on read to convert the loginuid into the
user namespace of the opener of the file.
Modify /proc/<pid>/loginud on write to convert the loginuid
rom the user namespace of the opener of the file.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Paul Moore <paul@paul-moore.com> ?
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Return the value returned by the failing function instead
of -1 (which does not convey the right error information).
Fixes the following smatch warning:
drivers/tty/serial/samsung.c:1687 s3c24xx_serial_modinit() info:
why not propagate 'ret' from uart_register_driver() instead of -1?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the trace we print the wrong values for N(R) on an I frame.
Correct the mask.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we start trying to use a bogus channel - ungood.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to free a random address if the entry is wrong, cover
this and WARN if it ever happens.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HVC returns a size of -1 bytes for the write room in some cases.
This is bogus and not handled by the tty layer at all.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
From "Uwe Kleine-Knig" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'x86/platform' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (9690 commits)
x86: Document x86_init.paging.pagetable_init()
x86: xen: Cleanup and remove x86_init.paging.pagetable_setup_done()
x86: Move paging_init() call to x86_init.paging.pagetable_init()
x86: Rename pagetable_setup_start() to pagetable_init()
x86: Remove base argument from x86_init.paging.pagetable_setup_start
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
...
The mxs_auart_probe() gets the device by the get_device().
So we should put the device in the error path to balance the
device's reference counter.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These workarounds do not apply for CONFIG_ARCH_OMAP2PLUS at all,
so let's make it just CONFIG_ARCH_OMAP1.
This is needed to for ARM common zImage changes for
omap2+ to avoid including plat and mach headers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/tty/serial/mpc52xx_uart.c: In function 'mpc52xx_uart_of_enumerate':
drivers/tty/serial/mpc52xx_uart.c:1440:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
On some machines using a specific hardware for console screen output,
the update of the pixel frame buffer does not work correctly when
using command line edition. This may be due to a memory cache bug
in the machine on which the problem has been found, but an other
solution is possible.
This patch proposes to avoid touching directly the pixel frame buffer
and to rebuild each character using the standard putc() function
on command line edition.
The resulting code is smaller and not obviously slower (no read
access to the pixel frame buffer).
Tested on a Cubox (ARM Marvell Dove 88AP510 SoC).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver explicitly requests a clock rate for the UART, but it is
off by a factor of four from the dividers that it programs into the
UART. Fix this by setting the rate to 1/4 of the current value.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug flag .interrupt_may_hang is not used since commit
4fd0690bb0
"serial: pl011: implement workaround for CTS clear event issue"
so delete it.
Cc: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request pins using pinctrl framework. Only show a warning
on error as some boards set the pins in the bootloader
even if CONFIG_PINCTRL is enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP Architecture code, passes a few function
pointers for UART driver to use in order to
properly implement Power Management and Wakeup
capabilities.
The problem is that those function pointers,
which are passed (ab)using platform_data on
non-DT kernels, can't be passed down to drivers
through DT.
commit e5b57c0 (serial: omap: define helpers
for pdata function pointers) failed to take DT
kernels into consideration and caused a regression
to DT kernel boot.
Fix that by (re-)adding a check for valid pdata
pointer together with valid pdata->$FUNCTION
pointer.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Covers the rest of the uses of pci error handler.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
when rebasing patches on top of Greg's tty-next,
it looks like automerge broke a few things which
I didn't catch (for whatever reason I didn't
have OMAP Serial enabled on .config) so I ended
up breaking the build on Greg's tty-next branch.
Fix the breakage by re-adding the three missing
members on struct uart_omap_port.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added tty_device_create_release() and bound to dev->release in
tty_register_device_attr().
Added tty_port_register_device_attr() and used in uart_add_one_port()
instead of tty_register_device_attr().
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added file /sys/devices/.../tty/ttySX/uartclk to allow reading
uartclk value in struct uart_port in serial_core via sysfs.
tty_register_device() has been generalized and refactored in order
to add support for setting drvdata and attribute_group to the device.
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes these build errors:
In file included from drivers/tty/serial/sccnxp.c:20:0:
include/linux/serial_core.h: In function 'uart_handle_break':
include/linux/serial_core.h:543:30: error: dereferencing pointer to incomplete type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We call the get_device() in the mxs_auart_probe().
For the balance of the reference count, we should put the
device in the mxs_auart_remove().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After set the AUART_CTRL0_CLKGATE, the UART will gate all the clocks off.
So the following line will not take effect.
................................................................
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
u->membase + AUART_INTR_CLR);
................................................................
To fix this issue, the patch moves this gate-off line to
the end of setting registers.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the
size of the pointer.
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enable RX FIFO for 16 characters and TX FIFO
for 16 spaces.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nobody needs to access the uart_omap_port structure
other than omap-serial.c file. Let's move that
structure definition to the C source file in order
to prevent anyone from accessing our structure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this driver doesn't use any from <plat/dmtimer.h>, so
we can remove it without any problems.
This will, however cause a problem because omap-serial.c
was relying on indirect inclusion of <linux/platform_device.h>,
let's fix the issue by including <linux/platform_device.h>
on omap-serial.c as it should be.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software flow control register bits were not defined correctly.
Also clarify the IXON and IXOFF logic to reflect what userspace wants.
Cc: stable@vger.kernel.org
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if we would reach serial_omap_get_char() while
Data Ready bit isn't set, we would return from
it without kicking our pm timer. This would mean
we would, eventually, have an unbalanced
pm_runtime_get on our device which would prevent
it from ever sleeping again.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been missing from OMAP UART driver
for quite a while and it's simple enough
to implement it.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch unlocks the port lock before calling a serial_core API
and re-acquires the port lock after calling it.
This patch fixes a system freeze issue seen when the serial_core
API uart_write_wakeup() eventually attempts to acquire the port lock
already acquired by omap serial interrupt handler.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
it makes no sense to mark our IRQ handler inline
since it's passed as a function pointer when
enabling the IRQ line.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two functions:
omap_serial_fill_features_erratas() and
of_get_uart_port_info() are only called from probe().
Marking them as __devinit gives us another
oportunity to free some code after .init.text
is done.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_enable() needs to be invoked before
pm_runtime_use_autosuspend(), and
pm_runtime_set_autosuspend_delay() functions.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we're running our hardirq handler, there's
not need to disable IRQs with spin_lock_irqsave()
because IRQs are already disabled. It also makes
no difference if we save or not IRQ flags.
Switch over to simple spin_lock/spin_unlock and
drop the "flags" variable.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
before removing the driver, let's make sure
to force device into a suspended state in order
to conserve power.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if platform_get_drvdata() returns NULL, that's
quite a nasty bug on the driver which we want to
catch ASAP. Otherwise, that check is hugely
unneeded.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
by the time we call our first pm_runtme_get_sync()
after enable pm_runtime, our resume method might
be called. To avoid problems, we must make sure
that our dev->drvdata is set correctly before
our resume method gets called.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Everytime we're done using our TTY, we want
the pm timer to be reinitilized. By sticking
to pm_runtime_pm_autosuspend() we make sure
that this will always be the case.
The idea behind this patch is to make sure we
will always reinitialize the pm timer so that
we don't fall into a situation where pm_runtime_put()
expires right away (if timer was already about to
expire when we made the call to pm_runtime_put()).
While suspending right away wouldn't cause any
issues, reinitializing the pm timer can help us
avoiding unnecessary context save & restore
operations (which are somewhat expensive) if there's
another read/write/set_termios request coming right
after. IOW, we are trying to make sure UART is still
powered up while it's still under heavy usage.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since all other IRQ types now do all necessary
checks inside their handlers, transmit_chars()
was the only one left expecting serial_omap_irq()
to check THRE for it. We can move THRE check to
transmit_chars() in order to make serial_omap_irq()
more uniform.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
receive_chars() was getting too big and too difficult
to follow. By splitting it into separate RDI and RSLI
handlers, we have smaller functions which are easy
to understand and only touch the pieces which they need
to touch.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quite a few changes here, though they are
pretty obvious. In summary we're making sure
to detect which interrupt type we need to
handle before calling the underlying interrupt
handling procedure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current support is known to be broken and
a later patch will come re-adding it using
dma engine API.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't need to know about its platform_device.
Everything the driver needs can be done through the
struct device pointer. In case we need to use the
OMAP-specific PM function pointers, those can make
sure to find the device's platform_device pointer
so they can find the struct omap_device through
pdev->archdata field.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These were reported in bugzilla long ago with a hack patch. Now we have a
proper patch for one we can do the rest.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=25102
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most of the time, the driver needs to check if the cts flow control
is enabled. But now, the driver checks the ASYNC_CTS_FLOW flag manually,
which is not a grace way. So add a new wraper function to make the code
tidy and clean.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch is in preparation to a few other changes
which will align on the prototype for function
pointers passed through pdata.
It also helps cleaning up the driver a little by
agregating checks for pdata in a single location.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
current code only works because struct uart_port
is the first member on the uart_omap_port structure.
If, for whatever reason, someone puts another
member as the first of the structure, that cast
won't work anymore. In order to be safe, let's use
a container_of() which, for now, gets optimized into
a cast anyway.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds note about migration to driver SCCNXP in the code
of driver SC26XX and in MIPS SNI board initialization with example.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a replacement for a SC26XX driver with a lot of
improvements and new features.
The main differences from the SC26XX driver:
- Removed dependency on MIPS. Driver can be used on any platform.
- Added support for SCC2681, SCC2691, SCC2692, SC28L91, SC28L92,
SC28L202, SCC68681 and SCC68692 ICs.
- Using devm_-related functions.
- Improved error handling of serial port, improved FIFO handling.
- Ability to load multiple instances of drivers.
To avoid the possibility of regression, driver SC26XX left in the
system to confirm the stability of the driver on platforms where
it is being used.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow parport_serial to handle the card the same PCI ids are blacklisted
in 8250_pci.c using the existing software blacklist mechanism.
The blacklist array is also renamed because it now covers this new use
case.
Since the two serial ports are auto-detected as XScale instead of 16550A
clones, we also add a quirk to 8250_pci.c to skip autodetection and set the
correct port type.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
[Fold in fixes for the uart_8250 change]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following errors and warnings:
ERROR: trailing whitespace
ERROR: return is not a function, parentheses are not required
WARNING: suspect code indent for conditional statements (32, 36)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the order of UART nodes is changed in the device tree, then tty dev
devices are attached to different serial ports causing the console to
be directed to a different physical serial port. The "serial" aliases
in the device tree should prevent this.
This patch ensures that the UART driver creates tty devices that
honour these aliases if a device tree is present.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure might have made sense many years ago, but at this
point it is only used in one specific driver, and referenced in
stale comments elsewhere. Rather than change the sunsu.c driver,
simply move the struct to be within the exclusive domain of that
driver, so it won't get inadvertently picked up and used by other
serial drivers going forward. The comments referencing the now
driver specific struct are updated accordingly.
Note that 8250.c has a struct that is similar in usage, with the
name serial8250_config; but is 100% independent and untouched here.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The addition of 8250-like entities continues to grow, while this
driver has a snapshot of a select few common 8250 UARTs. So it
has no need to grow with the new additions, since it calls out
its own (largely historic) static list which does not grow.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct serial_uart_config is hardly used at all, and the
use case like this one are somewhat needless. Remove the
trivial usage so that we can remove serial_uart_config.
Since the type field isn't really used at all, we also delete
the initialization and references of it here as well.
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These error paths are used more often now after deep changes to the
clock code and pinctrl is still new for imx. So help debugging and give
clues in the boot log.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want them split so that we can call them from setserial functionality
where we copy to/from user space and do the locking, but also from sysfs
where in future we'll want to came them within a sysfs context.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm free functions should not have to be explicitly used.
A semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
(
* devm_kfree(...);
|
* devm_free_irq(...);
|
* devm_iounmap(...);
|
* devm_release_region(...);
|
* devm_release_mem_region(...);
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested on a custom MPC5200B-board using some fancy industrial protocol.
Verified that MPC512x has identical bits, so should work there as well.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.
For example:
fd = open("/dev/tty", O_RDWR);
ioctl(fd, -1, &argp);
then the errno should be ENOTTY but not EINVAL.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to explicitly call devm_kfree
in probe or remove functions.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpiochip_remove function may fail to remove a gpio_chip
if any GPIOs are still requested. This patch informs the caller
of such a senario.
Sparse is warning because the function prototype has a
__must_check annotation.
Sparse warning:
drivers/tty/serial/max310x.c:1223:18: warning:
ignoring return value of ‘gpiochip_remove’,
declared with attribute warn_unused_result
[-Wunused-result]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions, so we can directly pass a struct
platfrom_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the driver's module init and exit functions can be replaced
with module_spi_driver as they do
only spi_register_driver and spi_unregister_driver in module's init and exit
paths.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clk_prepare_enable and clk_disable_unprepare combine clk_prepare and
clk_enable, and clk_disable and clk_unprepare. The9 make the code more
concise, and ensure that clk_unprepare is called when clk_enable fails.
A simplified version of the semantic patch that introduces calls to these
functions is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- clk_prepare(e);
- clk_enable(e);
+ clk_prepare_enable(e);
@@
expression e;
@@
- clk_disable(e);
- clk_unprepare(e);
+ clk_disable_unprepare(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pseries hvterm driver only registers a udbg backend (for xmon and
other low level debugging mechanisms) when hvc0 is recognized as the
firmware console at boot time, not if it's detected later on, for
example because the firmware is using a graphics card.
This can make debugging challenging especially under X11, and there's
really no good reason for that limitation, so let's hookup udbg
whenever hvc0 is detected instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
hvc_console has two methods to instanciate the consoles.
hvc_instanciate is meant to be called at early boot, while hvc_alloc is
called for more dynamically probed objects.
Currently, it only deals with adding kernel consoles in the former case,
which means for example that if a console only uses dynamic probing, it
will never be usable as a kernel console even when specifying
console=hvc0 explicitly, which could be considered annoying...
More specifically, on pseries, we only do the early instanciate for the
console currently used by the firmware, so if you have your firmware
configured to go to a video card, for example, you cannot get your
kernel console, oops messages, etc... on your serial port or hypervisor
console, which would be handy to deal with oopses.
This fixes it by checking if hvc_console.flags & CON_ENABLED is set when
registering a new dynamic console, and if not, redo the index check and
re-register the console if the index matches, allowing console=hvcN to
work.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
And if not, complain loudly. None in-kernel module should trigger
that, but let us find out for sure. On the other hand, all the
out-of-tree modules will hit that. Give them some time (maybe one
release) to catch up.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kdb <-> kgdb transitioning does not work properly with this UART
driver because the get character routine loops indefinitely as opposed
to returning NO_POLL_CHAR per the expectation of the KDB I/O driver
API.
The symptom is a kernel hang when trying to switch debug modes.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking if the auart supports the hardware flow control or not,
the old mxs_auart_set_mctrl() asserted the RTS pin blindly.
This will causes the auart receives wrong data in the following case:
The far-end has already started the write operation, and wait for
the auart asserts the RTS pin. Then the auart starts the read operation,
but mxs_auart_set_mctrl() may be called before we set the RTSCTS in the
mxs_auart_settermios(). So the RTS pin is asserted in a wrong situation,
and we get the wrong data in the end.
This bug has been catched when I connect the mx23(DTE) to the mx53(DCE).
This patch also replaces the AUART_CTRL2_RTS with AUART_CTRL2_RTSEN.
We should use the real the hardware flow control, not the software-controled
hardware flow control.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a replacement for a MAX3107 driver with a lot of
improvements and new features.
The main differences from the old version:
- Using the regmap.
- Using devm_XXX-related functions.
- The use of threaded IRQ with IRQF_ONESHOT flag allows the driver to
the hardware that supports only level IRQ.
- Improved error handling of serial port, improved FIFO handling,
improved hardware & software flow control.
- Advanced flags allows turn on RS-485 mode (Auto direction control).
- Ability to load multiple instances of drivers.
- Added support for MAX3108.
- GPIO support.
- Driver is quite ready for adding I2C support and support other ICs
with compatible registers set (MAX3109, MAX14830).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP hardware doesn't provide a phyisical DTR line, but
some configurations may need a DTR line which tracks whether
the device is open or not.
So allow a gpio to be configured as the DTR line.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by coccinelle:
drivers/tty/serial/pch_uart.c:979:1-14: alloc with no test, possible model on line 994
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following compile breakage:
CC drivers/tty/serial/sc26xx.o
drivers/tty/serial/sc26xx.c: In function 'read_sc_port':
drivers/tty/serial/sc26xx.c💯 error: implicit declaration of function 'readb'
drivers/tty/serial/sc26xx.c: In function 'write_sc_port':
drivers/tty/serial/sc26xx.c:105: error: implicit declaration of function 'writeb'
drivers/tty/serial/sc26xx.c: In function 'sc26xx_probe':
drivers/tty/serial/sc26xx.c:652: error: implicit declaration of function 'ioremap_nocache'
drivers/tty/serial/sc26xx.c:652: warning: assignment makes pointer from integer without a cast
make[3]: *** [drivers/tty/serial/sc26xx.o] Error 1
make[2]: *** [drivers/tty/serial] Error 2
make[1]: *** [drivers/tty] Error 2
make: *** [drivers] Error 2
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We changed these from alloc_tty_driver() to tty_alloc_driver() so the
error handling needs to modified to check for IS_ERR() instead of NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uplink (TX) network data will go through gsm_dlci_data_output_framed
there is a bug where if memory allocation fails, the skb which
has already been pulled off the list will be lost.
In addition TX skbs were being processed in LIFO order
Fixed the memory leak, and changed to FIFO order processing
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Showjumping <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are supposed to use the dev_* versions of the kfree_skb
interfaces. In a couple of cases we were called with IRQs
disabled as well which kfree_skb() does not expect.
Replaced kfree_skb calls w/ dev_kfree_skb and dev_kfree_skb_any
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Grooming <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_data_kick was recently modified to allow messages on the
tx queue bound for DLCI0 to flow even during FCOFF conditions.
Unfortunately we introduced a bug discovered by code inspection
where subsequent list traversers can access freed memory if
the DLCI0 messages were not all at the head of the list.
Replaced singly linked tx list w/ a list_head and used
provided interfaces for traversing and deleting members.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some locking holes in the management of the MUX's
message queue for 2 code paths:
1) gsmld_write_wakeup
2) receipt of CMD_FCON flow-control message
In both cases gsm_data_kick is called w/o locking so it can collide
with other other instances of gsm_data_kick (pulling messages tx_tail)
or potentially other instances of __gsm_data_queu (adding messages to tx_head)
Changed to take the tx_lock in these 2 cases
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The design of uplink flow control in the mux driver is
that for constipated channels data will backup into the
per-channel fifos, and any messages that make it to the
outbound message queue will still go out.
Code was added to also stop messages that were in the outbound
queue but this requires filtering through all the messages on the
queue for stopped dlcis and changes some of the mux logic unneccessarily.
The message fiiltering was removed to be in line w/ the original design
as the message filtering does not provide any solution.
Extra debug messages used during investigation were also removed.
Signed-off-by: samix.lebsir <samix.lebsir@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Dressage <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Correcting handling of FCon/FCoff in order to respect 27.010 spec
- Consider FCon/off will overide all dlci flow control except for
dlci0 as we must be able to send control frames.
- Dlci constipated handling according to FC, RTC and RTR values.
- Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according
to dlci constipated value
Signed-off-by: Frederic Berat <fredericx.berat@intel.com>
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO
furthermore it will call the output function only once if tx_bytes == 0
If the size of the IP writes are on the order of THRESH_LO
we can get into a situation where skbs accumulate on the outbound list
being starved for events to call the output function.
gsm_dlci_data_kick now calls the sweep function when tx_bytes==0
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Hay and Water <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3GPP27.010 5.8.1, it defined:
The TE multiplexer initiates the establishment of the multiplexer control channel by sending a SABM frame on DLCI 0 using the procedures of clause 5.4.1.
Once the multiplexer channel is established other DLCs may be established using the procedures of clause 5.4.1.
This patch implement 5.8.1 in MUX level, it make sure DLC0 is the first channel to be setup.
[or for those not familiar with the specification: it was possible to try
and open a data connection while the control channel was not yet fully
open, which is a spec violation and confuses some modems]
Signed-off-by: xiaojin <jin.xiao@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
[tweaked the order we check things and error code]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: The Horsebox <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a
couple of long standing reports of this but at the same time we can avoid killing the box.
Signed-off-by: Stanislav Kozina <skozina@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Horses <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
444 means 0674 and we do not definitely want that. Use S_IRUGO which
is much more safer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Rusty Russell <rusty@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
>From now on, we only increase the reference count in ->install (and
decrease in ->cleanup).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code of hvcs_open a bit more readable by:
- moving all assignments out of if's
- redoing fail paths so that corresponding pieces are nearby
- we need only one of retval and rc
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Since we take a reference to a port in ->install, we need also
->cleanup to drop that reference.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows us to provide the tty layer with information about
tty_port for each link.
We also provide a tty_port for the service port. For this one we allow
only ioctl, so this is pretty ugly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now for those drivers that can use neither tty_port_install nor
tty_port_register_driver but still have tty_port available before
tty_register_driver we use newly added tty_port_link_device.
The rest of the drivers that still do not provide tty_struct <->
tty_port link will have to be converted to implement
tty->ops->install.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is for those drivers which do not have dynamic device creation
(do not call tty_port_register_device) and do not want to implement
tty->ops->install (will not call tty_port_install). They still have to
provide the link somehow though.
And this newly added function is exactly to serve that purpose.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I forgot to document tty_port_register_device and tty_port_install
when they were added. Fix it now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This looks like it was a mistake not to create device nodes for these
drivers. Let us create them from now on.
It will be necessary to call tty_register_device some way, either by
tty_register_driver implicitly or to call tty_register_device proper.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Cc: linux-cris-kernel@axis.com
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxime Bizon