Currently the size of the speculative preallocation during delayed
allocation is fixed by either the allocsize mount option of a
default size. We are seeing a lot of cases where we need to
recommend using the allocsize mount option to prevent fragmentation
when buffered writes land in the same AG.
Rather than using a fixed preallocation size by default (up to 64k),
make it dynamic by basing it on the current inode size. That way the
EOF preallocation will increase as the file size increases. Hence
for streaming writes we are much more likely to get large
preallocations exactly when we need it to reduce fragementation.
For default settings, the size of the initial extents is determined
by the number of parallel writers and the amount of memory in the
machine. For 4GB RAM and 4 concurrent 32GB file writes:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL
0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576
1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576
2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152
3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304
4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608
5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208
6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088
7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088
and for 16 concurrent 16GB file writes:
EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL
0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144
1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144
2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288
3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576
4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152
5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304
6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608
7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208
Because it is hard to take back specualtive preallocation, cases
where there are large slow growing log files on a nearly full
filesystem may cause premature ENOSPC. Hence as the filesystem nears
full, the maximum dynamic prealloc size іs reduced according to this
table (based on 4k block size):
freespace max prealloc size
>5% full extent (8GB)
4-5% 2GB (8GB >> 2)
3-4% 1GB (8GB >> 3)
2-3% 512MB (8GB >> 4)
1-2% 256MB (8GB >> 5)
<1% 128MB (8GB >> 6)
This should reduce the amount of space held in speculative
preallocation for such cases.
The allocsize mount option turns off the dynamic behaviour and fixes
the prealloc size to whatever the mount option specifies. i.e. the
behaviour is unchanged.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
The walk fails to decrement the per-ag reference count when the
non-blocking walk fails to obtain the per-ag reclaim lock, leading
to an assert failure on debug kernels when unmounting a filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Stop having two different names for many buffer functions and use
the more descriptive xfs_buf_* names directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Update the per-cpu counters manually in xfs_trans_unreserve_and_mod_sb
and remove support for per-cpu counters from xfs_mod_incore_sb_batch
to simplify it. And added benefit is that we don't have to take
m_sb_lock for transactions that only modify per-cpu counters.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Export xfs_icsb_modify_counters and always use it for modifying
the per-cpu counters. Remove support for per-cpu counters from
xfs_mod_incore_sb to simplify it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Fail the mount if we can't allocate memory for the per-CPU counters.
This is consistent with how we handle everything else in the mount
path and makes the superblock counter modification a lot simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
The buffer cache hash is showing typical hash scalability problems.
In large scale testing the number of cached items growing far larger
than the hash can efficiently handle. Hence we need to move to a
self-scaling cache indexing mechanism.
I have selected rbtrees for indexing becuse they can have O(log n)
search scalability, and insert and remove cost is not excessive,
even on large trees. Hence we should be able to cache large numbers
of buffers without incurring the excessive cache miss search
penalties that the hash is imposing on us.
To ensure we still have parallel access to the cache, we need
multiple trees. Rather than hashing the buffers by disk address to
select a tree, it seems more sensible to separate trees by typical
access patterns. Most operations use buffers from within a single AG
at a time, so rather than searching lots of different lists,
separate the buffer indexes out into per-AG rbtrees. This means that
searches during metadata operation have a much higher chance of
hitting cache resident nodes, and that updates of the tree are less
likely to disturb trees being accessed on other CPUs doing
independent operations.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Memory reclaim via shrinkers has a terrible habit of having N+M
concurrent shrinker executions (N = num CPUs, M = num kswapds) all
trying to shrink the same cache. When the cache they are all working
on is protected by a single spinlock, massive contention an
slowdowns occur.
Wrap the per-ag inode caches with a reclaim mutex to serialise
reclaim access to the AG. This will block concurrent reclaim in each
AG but still allow reclaim to scan multiple AGs concurrently. Allow
shrinkers to move on to the next AG if it can't get the lock, and if
we can't get any AG, then start blocking on locks.
To prevent reclaimers from continually scanning the same inodes in
each AG, add a cursor that tracks where the last reclaim got up to
and start from that point on the next reclaim. This should avoid
only ever scanning a small number of inodes at the satart of each AG
and not making progress. If we have a non-shrinker based reclaim
pass, ignore the cursor and reset it to zero once we are done.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
The reclaim walk requires different locking and has a slightly
different walk algorithm, so separate it out so that it can be
optimised separately.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When we are checking we can access the last block of each device, we
do not need to use cached buffers as they will be tossed away
immediately. Use uncached buffers for size checks so that all IO
prior to full in-memory structure initialisation does not use the
buffer cache.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Filesystem level managed buffers are buffers that have their
lifecycle controlled by the filesystem layer, not the buffer cache.
We currently cache these buffers, which makes cleanup and cache
walking somewhat troublesome. Convert the fs managed buffers to
uncached buffers obtained by via xfs_buf_get_uncached(), and remove
the XBF_FS_MANAGED special cases from the buffer cache.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When we start taking a reference to the per-ag for every cached
buffer in the system, kernel lockstat profiling on an 8-way create
workload shows the mp->m_perag_lock has higher acquisition rates
than the inode lock and has significantly more contention. That is,
it becomes the highest contended lock in the system.
The perag lookup is trivial to convert to lock-less RCU lookups
because perag structures never go away. Hence the only thing we need
to protect against is tree structure changes during a grow. This can
be done simply by replacing the locking in xfs_perag_get() with RCU
read locking. This removes the mp->m_perag_lock completely from this
path.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When we start taking references per cached buffer to the the perag
it is cached on, it will blow the current debug maximum reference
count assert out of the water. The assert has never caught a bug,
and we have tracing to track changes if there ever is a problem,
so just remove it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Dmapi support was never merged upstream, but we still have a lot of hooks
bloating XFS for it, all over the fast pathes of the filesystem.
This patch drops over 700 lines of dmapi overhead. If we'll ever get HSM
support in mainline at least the namespace events can be done much saner
in the VFS instead of the individual filesystem, so it's not like this
is much help for future work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
The block number comes from bulkstat based inode lookups to shortcut
the mapping calculations. We ar enot able to trust anything from
bulkstat, so drop the block number as well so that the correct
lookups and mappings are always done.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
If a filesystem is mounted without the inode64 mount option we
should still be able to access inodes not fitting into 32 bits, just
not created new ones. For this to work we need to make sure the
inode cache radix tree is initialized for all allocation groups, not
just those we plan to allocate inodes from. This patch makes sure
we initialize the inode cache radix tree for all allocation groups,
and also cleans xfs_initialize_perag up a bit to separate the
inode32 logical from the general perag structure setup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
The use of radix_tree_preload() only works if the radix tree was
initialised without the __GFP_WAIT flag. The per-ag tree uses
GFP_NOFS, so does not trigger allocation of new tree nodes from the
preloaded array. Hence it enters the allocator with a spinlock held
and triggers the might_sleep() warnings.
Reported-by; Chris Mason <chris.mason@oracle.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Many places in the xfs code return E2BIG when they really mean
EFBIG; trying to grow past 16T on a 32 bit machine, for example,
says "Argument list too long" rather than "File too large" which is
not particularly helpful.
Some of these don't make perfect sense as EFBIG either, but still
better than E2BIG IMHO.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
This can't be enabled through the build system and has been dead for
ages. Note that the CRC patches add back log checksumming, but the
code is quite different from the version removed here anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
The current default size of the reserved blocks pool is easy to deplete
with certain workloads, in particular workloads that do lots of concurrent
delayed allocation extent conversions. If enough transactions are running
in parallel and the entire pool is consumed then subsequent calls to
xfs_trans_reserve() will fail with ENOSPC. Also add a rate limited
warning so we know if this starts happening again.
This is an updated version of an old patch from Lachlan McIlroy.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Currently the code to implement the file operations is split over
two small files. Merge the content of xfs_lrw.c into xfs_file.c to
have it in one place. Note that I haven't done various cleanups
that are possible after this yet, they will follow in the next
patch. Also the function xfs_dev_is_read_only which was in
xfs_lrw.c before really doesn't fit in here at all and was moved to
xfs_mount.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
We currently do background inode flush asynchronously, resulting in
inodes being written in whatever order the background writeback
issues them. Not only that, there are also blocking and non-blocking
asynchronous inode flushes, depending on where the flush comes from.
This patch completely removes asynchronous inode writeback. It
removes all the strange writeback modes and replaces them with
either a synchronous flush or a non-blocking delayed write flush.
That is, inode flushes will only issue IO directly if they are
synchronous, and background flushing may do nothing if the operation
would block (e.g. on a pinned inode or buffer lock).
Delayed write flushes will now result in the inode buffer sitting in
the delwri queue of the buffer cache to be flushed by either an AIL
push or by the xfsbufd timing out the buffer. This will allow
accumulation of dirty inode buffers in memory and allow optimisation
of inode cluster writeback at the xfsbufd level where we have much
greater queue depths than the block layer elevators. We will also
get adjacent inode cluster buffer IO merging for free when a later
patch in the series allows sorting of the delayed write buffers
before dispatch.
This effectively means that any inode that is written back by
background writeback will be seen as flush locked during AIL
pushing, and will result in the buffers being pushed from there.
This writeback path is currently non-optimal, but the next patch
in the series will fix that problem.
A side effect of this delayed write mechanism is that background
inode reclaim will no longer directly flush inodes, nor can it wait
on the flush lock. The result is that inode reclaim must leave the
inode in the reclaimable state until it is clean. Hence attempts to
reclaim a dirty inode in the background will simply skip the inode
until it is clean and this allows other mechanisms (i.e. xfsbufd) to
do more optimal writeback of the dirty buffers. As a result, the
inode reclaim code has been rewritten so that it no longer relies on
the ambiguous return values of xfs_iflush() to determine whether it
is safe to reclaim an inode.
Portions of this patch are derived from patches by Christoph
Hellwig.
Version 2:
- cleanup reclaim code as suggested by Christoph
- log background reclaim inode flush errors
- just pass sync flags to xfs_iflush
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This mangles the reserved blocks counts a little more.
1) add a helper function for the default reserved count
2) add helper functions to save/restore counts on ro/rw
3) save/restore reserved blocks on freeze/thaw
4) disallow changing reserved count while readonly
V2: changed field name to match Dave's changes
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Alex Elder <aelder@sgi.com>
Remove the XFS_LOG_FORCE argument which was always set, and the
XFS_LOG_URGE define, which was never used.
Split xfs_log_force into a two helpers - xfs_log_force which forces
the whole log, and xfs_log_force_lsn which forces up to the
specified LSN. The underlying implementations already were entirely
separate, as were the users.
Also re-indent the new _xfs_log_force/_xfs_log_force which
previously had a weird coding style.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Currently we define aliases for the buffer flags in various
namespaces, which only adds confusion. Remove all but the XBF_
flags to clean this up a bit.
Note that we still abuse XFS_B_ASYNC/XBF_ASYNC for some non-buffer
uses, but I'll clean that up later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
gcc warns of an array subscript out of bounds in xfs_mod_sb().
The code is written in such a way that if the array subscript is
out of bounds, then it will assert fail. Rearrange the code to
avoid the bounds check warning.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Now that the perag structure is allocated memory rather than held in
an array, we don't need to have the busy extent array external to
the structure. Embed it into the perag structure to avoid needing an
extra allocation when setting up.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Add proper error handling in case an error occurs while initializing
new perag structures for a mount point. The mount structure is
restored to its previous state by deleting and freeing any perag
structures added during the call.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Uninline xfs_perag_{get,put} so that tracepoints can be inserted
into them to speed debugging of reference count problems.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reference count the per-ag structures to ensure that we keep get/put
pairs balanced. Assert that the reference counts are zero at unmount
time to catch leaks. In future, reference counts will enable us to
safely remove perag structures by allowing us to detect when they
are no longer in use.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
The use of an array for the per-ag structures requires reallocation
of the array when growing the filesystem. This requires locking
access to the array to avoid use after free situations, and the
locking is difficult to get right. To avoid needing to reallocate an
array, change the per-ag structures to an allocated object per ag
and index them using a tree structure.
The AGs are always densely indexed (hence the use of an array), but
the number supported is 2^32 and lookups tend to be random and hence
indexing needs to scale. A simple choice is a radix tree - it works
well with this sort of index. This change also removes another
large contiguous allocation from the mount/growfs path in XFS.
The growing process now needs to change to only initialise the new
AGs required for the extra space, and as such only needs to
exclusively lock the tree for inserts. The rest of the code only
needs to lock the tree while doing lookups, and hence this will
remove all the deadlocks that currently occur on the m_perag_lock as
it is now an innermost lock. The lock is also changed to a spinlock
from a read/write lock as the hold time is now extremely short.
To complete the picture, the per-ag structures will need to be
reference counted to ensure that we don't free/modify them while
they are still in use. This will be done in subsequent patch.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Convert the remaining direct lookups of the per ag structures to use
get/put accesses. Ensure that the loops across AGs and prior users
of the interface balance gets and puts correctly.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Convert the old xfs tracing support that could only be used with the
out of tree kdb and xfsidbg patches to use the generic event tracer.
To use it make sure CONFIG_EVENT_TRACING is enabled and then enable
all xfs trace channels by:
echo 1 > /sys/kernel/debug/tracing/events/xfs/enable
or alternatively enable single events by just doing the same in one
event subdirectory, e.g.
echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable
or set more complex filters, etc. In Documentation/trace/events.txt
all this is desctribed in more detail. To reads the events do a
cat /sys/kernel/debug/tracing/trace
Compared to the last posting this patch converts the tracing mostly to
the one tracepoint per callsite model that other users of the new
tracing facility also employ. This allows a very fine-grained control
of the tracing, a cleaner output of the traces and also enables the
perf tool to use each tracepoint as a virtual performance counter,
allowing us to e.g. count how often certain workloads git various
spots in XFS. Take a look at
http://lwn.net/Articles/346470/
for some examples.
Also the btree tracing isn't included at all yet, as it will require
additional core tracing features not in mainline yet, I plan to
deliver it later.
And the really nice thing about this patch is that it actually removes
many lines of code while adding this nice functionality:
fs/xfs/Makefile | 8
fs/xfs/linux-2.6/xfs_acl.c | 1
fs/xfs/linux-2.6/xfs_aops.c | 52 -
fs/xfs/linux-2.6/xfs_aops.h | 2
fs/xfs/linux-2.6/xfs_buf.c | 117 +--
fs/xfs/linux-2.6/xfs_buf.h | 33
fs/xfs/linux-2.6/xfs_fs_subr.c | 3
fs/xfs/linux-2.6/xfs_ioctl.c | 1
fs/xfs/linux-2.6/xfs_ioctl32.c | 1
fs/xfs/linux-2.6/xfs_iops.c | 1
fs/xfs/linux-2.6/xfs_linux.h | 1
fs/xfs/linux-2.6/xfs_lrw.c | 87 --
fs/xfs/linux-2.6/xfs_lrw.h | 45 -
fs/xfs/linux-2.6/xfs_super.c | 104 ---
fs/xfs/linux-2.6/xfs_super.h | 7
fs/xfs/linux-2.6/xfs_sync.c | 1
fs/xfs/linux-2.6/xfs_trace.c | 75 ++
fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++
fs/xfs/linux-2.6/xfs_vnode.h | 4
fs/xfs/quota/xfs_dquot.c | 110 ---
fs/xfs/quota/xfs_dquot.h | 21
fs/xfs/quota/xfs_qm.c | 40 -
fs/xfs/quota/xfs_qm_syscalls.c | 4
fs/xfs/support/ktrace.c | 323 ---------
fs/xfs/support/ktrace.h | 85 --
fs/xfs/xfs.h | 16
fs/xfs/xfs_ag.h | 14
fs/xfs/xfs_alloc.c | 230 +-----
fs/xfs/xfs_alloc.h | 27
fs/xfs/xfs_alloc_btree.c | 1
fs/xfs/xfs_attr.c | 107 ---
fs/xfs/xfs_attr.h | 10
fs/xfs/xfs_attr_leaf.c | 14
fs/xfs/xfs_attr_sf.h | 40 -
fs/xfs/xfs_bmap.c | 507 +++------------
fs/xfs/xfs_bmap.h | 49 -
fs/xfs/xfs_bmap_btree.c | 6
fs/xfs/xfs_btree.c | 5
fs/xfs/xfs_btree_trace.h | 17
fs/xfs/xfs_buf_item.c | 87 --
fs/xfs/xfs_buf_item.h | 20
fs/xfs/xfs_da_btree.c | 3
fs/xfs/xfs_da_btree.h | 7
fs/xfs/xfs_dfrag.c | 2
fs/xfs/xfs_dir2.c | 8
fs/xfs/xfs_dir2_block.c | 20
fs/xfs/xfs_dir2_leaf.c | 21
fs/xfs/xfs_dir2_node.c | 27
fs/xfs/xfs_dir2_sf.c | 26
fs/xfs/xfs_dir2_trace.c | 216 ------
fs/xfs/xfs_dir2_trace.h | 72 --
fs/xfs/xfs_filestream.c | 8
fs/xfs/xfs_fsops.c | 2
fs/xfs/xfs_iget.c | 111 ---
fs/xfs/xfs_inode.c | 67 --
fs/xfs/xfs_inode.h | 76 --
fs/xfs/xfs_inode_item.c | 5
fs/xfs/xfs_iomap.c | 85 --
fs/xfs/xfs_iomap.h | 8
fs/xfs/xfs_log.c | 181 +----
fs/xfs/xfs_log_priv.h | 20
fs/xfs/xfs_log_recover.c | 1
fs/xfs/xfs_mount.c | 2
fs/xfs/xfs_quota.h | 8
fs/xfs/xfs_rename.c | 1
fs/xfs/xfs_rtalloc.c | 1
fs/xfs/xfs_rw.c | 3
fs/xfs/xfs_trans.h | 47 +
fs/xfs/xfs_trans_buf.c | 62 -
fs/xfs/xfs_vnodeops.c | 8
70 files changed, 2151 insertions(+), 2592 deletions(-)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
Remove our own STATIC_INLINE macro. For small function inside
implementation files just use STATIC and let gcc inline it, and for
those in headers do the normal static inline - they are all small
enough to be inlined for debug builds, too.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Currently the low-level buffer cache interfaces are highly confusing
as we have a _flags variant of each that does actually respect the
flags, and one without _flags which has a flags argument that gets
ignored and overriden with a default set. Given that very few places
use the default arguments get rid of the duplication and convert all
callers to pass the flags explicitly. Also remove the now confusing
_flags postfix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
When completing I/O requests we must not allow the memory allocator to
recurse into the filesystem, as we might deadlock on waiting for the
I/O completion otherwise. The only thing currently allocating normal
GFP_KERNEL memory is the allocation of the transaction structure for
the unwritten extent conversion. Add a memflags argument to
_xfs_trans_alloc to allow controlling the allocator behaviour.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Thomas Neumann <tneumann@users.sourceforge.net>
Tested-by: Thomas Neumann <tneumann@users.sourceforge.net>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The xfs_icsb_modify_counters() function no longer needs the cpu variable
if we use this_cpu_ptr() and we can get rid of get/put_cpu().
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Olaf Weber <olaf@sgi.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
A lot more functions could be made static, but they need
forward declarations; this does some easy ones, and also
found a few unused functions in the process.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
The noblock parameter of xfs_reclaim_inodes is only ever set to zero. Remove
it and all the conditional code that is never executed.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Kill the quota ops function vector and replace it with direct calls or
stubs in the CONFIG_XFS_QUOTA=n case.
Make sure we check XFS_IS_QUOTA_RUNNING in the right spots. We can remove
the number of those checks because the XFS_TRANS_DQ_DIRTY flag can't be set
otherwise.
This brings us back closer to the way this code worked in IRIX and earlier
Linux versions, but we keep a lot of the more useful factoring of common
code.
Eventually we should also kill xfs_qm_bhv.c, but that's left for a later
patch.
Reduces the size of the source code by about 250 lines and the size of
XFS module by about 1.5 kilobytes with quotas enabled:
text data bss dec hex filename
615957 2960 3848 622765 980ad fs/xfs/xfs.o
617231 3152 3848 624231 98667 fs/xfs/xfs.o.old
Fallout:
- xfs_qm_dqattach is split into xfs_qm_dqattach_locked which expects
the inode locked and xfs_qm_dqattach which does the locking around it,
thus removing XFS_QMOPT_ILOCKED.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
There had been reports where xfs filesystem was randomly
corrupted with fsfuzzer, and xfs failed to handle it
gracefully. This patch fixes couple of reported problem
by providing additional checks in the superblock
validation routine.
Signed-off-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
The uuid table handling should not be part of a semi-generic uuid library
but in the XFS code using it, so move those bits to xfs_mount.c and
refactor the whole glob to make it a proper abstraction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
With the upcoming v3 inodes the default attroffset needs to be calculated
for each specific inode, so we can't cache it in the superblock anymore.
Also replace the assert for wrong inode sizes with a proper error check
also included in non-debug builds. Note that the ENOSYS return for
that might seem odd, but that error is returned by xfs_mount_validate_sb
for all theoretically valid but not supported filesystem geometries.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
With the upcoming v3 inodes the inode data/attr area size needs to be
calculated for each specific inode, so we can't cache it in the superblock
anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Kill the current xfs_log_unmount wrapper and opencode the two function
calls in the only caller. Rename the current xfs_log_unmount_dealloc to
xfs_log_unmount as it undoes xfs_log_mount and the new name makes that
more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
When mount fails after allocating the real-time inodes we currently leak
them. Add a new helper to free the real-time inodes which can be used by
both the mount and unmount path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Clean up the error handling in xfs_mountfs. Use readable goto label names,
simplify the uuid handling and other error conditions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Currently the bad_features2 fixup and the alignment updates in the superblock
are skipped if we mount a filesystem read-only. But for the root filesystem
the typical case is to mount read-only first and only later remount writeable
so we'll never perform this update at all. It's not a big problem but means
the logs of people needing the fixup get spammed at every boot because they
never happen on disk.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
There's almost nothing left in this function, instead remove the IRELE
on the real times inodes and the call to XFS_QM_UNMOUNT into xfs_unmountfs.
For the regular unmount case that means it now also happenes after dmapi
notification, but otherwise there is no difference in behaviour.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
We never supported shared read-only filesystems, so remove the dead
code left over from IRIX for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Now that we have a separate xfs_icdinode_t for the in-core inode which
gets logged there is no need anymore for the xfs_dinode vs xfs_dinode_core
split - the fact that part of the structure gets logged through the inode
log item and a small part not can better be described in a comment.
All sizeof operations on the dinode_core either really wanted the
icdinode and are switched to that one, or had already added the size
of the agi unlinked list pointer. Later both will be replaced with
helpers once we get the larger CRC-enabled dinode.
Removing the data and attribute fork unions also has the advantage that
xfs_dinode.h doesn't need to pull in every header under the sun.
While we're at it also add some more comments describing the dinode
structure.
(First sent on October 7th)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Now that the deleted inodes list is unused, kill it. This also removes the
i_reclaim list head from the xfs_inode, shrinking it by two pointers.
SGI-PV: 988142
SGI-Modid: xfs-linux-melb:xfs-kern:32334a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
The function names xfs_finish_reclaim and xfs_finish_reclaim_all are not
very descriptive of what they are reclaiming. Rename to
xfs_reclaim_inode[s] to match the xfs_sync_inodes() function.
SGI-PV: 988142
SGI-Modid: xfs-linux-melb:xfs-kern:32330a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Now we've removed all users of the mount inode list, we can kill it. This
reduces the size of the xfs_inode by 2 pointers.
SGI-PV: 988139
SGI-Modid: xfs-linux-melb:xfs-kern:32293a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Clean up the way the maximum and minimum records for the btree blocks are
calculated. For the alloc and inobt btrees all the values are
pre-calculated in xfs_mount_common, and we switch the current loop around
the ugly generic macros that use cpp token pasting to generate type names
to two small helpers in normal C code. For the bmbt and bmdr trees these
helpers also exist, but can be called during runtime, too. Here we also
kill various macros dealing with them and inline the logic into the
get_minrecs / get_maxrecs / get_dmaxrecs methods in xfs_bmap_btree.c.
Note that all these new helpers take an xfs_mount * argument which will be
needed to determine the size of a btree block once we add support for
extended btree blocks with CRCs and other RAS information.
SGI-PV: 988146
SGI-Modid: xfs-linux-melb:xfs-kern:32292a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_iflush_all() walks the m_inodes list to find inodes that need
reclaiming. We already have such a list - the m_del_inodes list. Replace
xfs_iflush_all() with a call to xfs_finish_reclaim_all() and clean up
xfs_finish_reclaim_all() to handle the different flush modes now needed.
Originally based on a patch from Christoph Hellwig.
Version 3 o rediff against new linux-2.6/xfs_sync.c code
Version 2 o revert xfs_syncsub() inode reclaim behaviour back to original
code o xfs_quiesce_fs() should use XFS_IFLUSH_DELWRI_ELSE_ASYNC, not
XFS_IFLUSH_ASYNC, to prevent change of behaviour.
SGI-PV: 988139
SGI-Modid: xfs-linux-melb:xfs-kern:32284a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Destroying the quota stuff on unmount can access the log - ie
XFS_QM_DONE() ends up in xfs_dqunlock() which calls
xfs_trans_unlocked_item() and then xfs_log_move_tail(). By this time the
log has already been destroyed. Just move the cleanup of the quota code
earlier in xfs_unmountfs() before the call to xfs_log_unmount(). Moving
XFS_QM_DONE() up near XFS_QM_DQPURGEALL() seems like a good spot.
SGI-PV: 987086
SGI-Modid: xfs-linux-melb:xfs-kern:32148a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Peter Leckie <pleckie@sgi.com>
Use KM_MAYFAIL for the m_perag allocation, we can deal with the error
easily and blocking forever during mount is not a good idea either.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31837a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_mount_free mostly frees the perag data, which is something that is
duplicated in the mount error path.
Move the XFS_QM_DONE call to the caller and remove the useless
mutex_destroy/spinlock_destroy calls so that we can re-use it for the
mount error path. Also rename it to xfs_free_perag to reflect what it
does.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31836a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_readsb is called before xfs_mount so xfs_freesb should be called after
xfs_unmountfs, too. This means it now happens after a few things during
the of xfs_unmount which all have nothing to do with the superblock.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31835a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_unmounts can't and shouldn't return errors so declare it as returning
void.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31833a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Remove all the useless flags and code keyed off it in xfs_mountfs.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31831a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The root inode is allocated in xfs_mountfs so it should be release in
xfs_unmountfs. For the unmount case that means we do it after the the
xfs_sync(mp, SYNC_WAIT | SYNC_CLOSE) in the forced shutdown case and the
dmapi unmount event. Note that both reference the rip variable which might
be freed by that time in case inode flushing has kicked in, so strictly
speaking this might count as a bug fix
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31830a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
All the error injection is already enabled through ifdef DEBUG, so kill
the never set second cpp symbol to activate it without the rest of the
debugging infrastructure.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31771a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Add a helper to free the m_fsname/m_rtname/m_logname allocations and use
it properly for all mount failure cases. Also switch the allocations for
these to kstrdup while we're at it.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31728a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
If we don't do the blocksize/PAGESIZE check before calling
xfs_sb_validate_fsb_count() we can assert if we try to mount with a
blocksize > pagesize. The assert is valid so leave it and just move the
blocksize/pagesize check earlier.
SGI-PV: 983734
SGI-Modid: xfs-linux-melb:xfs-kern:31365a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
xfs_mount_init is inlined into xfs_fs_fill_super and allocation switched
to kzalloc. Plug a leak of the mount structure for most early mount
failures. Move xfs_icsb_init_counters to as late as possible in the mount
path and make sure to undo it so that no stale hotplug cpu notifiers are
left around on mount failures.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31196a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Currently closing the rt/log block device is done in the wrong spot, and
far too early. So revampt it:
- xfs_blkdev_put moved out of xfs_free_buftarg into the caller so that
it is done after tearing down the buftarg completely.
- call to xfs_unmountfs_close moved from xfs_mountfs into caller so
that it's done after tearing down the filesystem completely.
- xfs_unmountfs_close is renamed to xfs_close_devices and made static
in xfs_super.c
- opening of the block devices is split into a helper xfs_open_devices
that is symetric in use to xfs_close_devices
- xfs_unmountfs can now lose struct cred
- error handling around device opening sanitized in xfs_fs_fill_super
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31193a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Freeing of the superblock is already handled in the caller, and that is
more symmetric with the mount path, too.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31192a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Quite useless wrapper that doesn't help making the code more readable.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31184a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Recent changes to update the version number during mount (attr2 stuff)
failed to change the assert that checked for calid flags being changed on
mount. Clearly this path hasn't been exercised by the test code....
SGI-PV: 981950
SGI-Modid: xfs-linux-melb:xfs-kern:31183a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
kmem_free() function takes (ptr, size) arguments but doesn't actually use
second one.
This patch removes size argument from all callsites.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31050a
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
features2 fields.
Previously, mounting with noattr2 failed to achieve anything because
although it cleared the attr2 mount flag, it would set it again as soon as
it processed the superblock fields. The fix now has an explicit noattr2
flag and uses it later to fix up the versionnum and features2 fields.
SGI-PV: 980021
SGI-Modid: xfs-linux-melb:xfs-kern:31003a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
With the last two patches XFS_ICSB_SB_LOCKED is never checked and only
superflously passed to xfs_icsb_count, so kill it.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30920a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Add an xfs_icsb_balance_counter_locked for the case where mp->m_sb_lock is
already locked.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30918a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Add a new xfs_icsb_sync_counters_locked for the case where m_sb_lock
is already taken and add a flags argument to xfs_icsb_sync_counters so
that xfs_icsb_sync_counters_flags is not needed.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30917a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfsbdstrat() is declared to return an error. That is never checked because
the error is propagated by the xfs_buf_t that is passed through the
function.
Mark xfsbdstrat() as returning void and comment the prototype on the
methods needed for error checking.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30823a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_trans_commit() can return errors when there are problems in the
transaction subsystem. They are indicative that the entire transaction may
be incomplete, and hence the error should be propagated as there is a good
possibility that there is something fatally wrong in the filesystem. Catch
and propagate or warn about commit errors in the places where they are
currently ignored.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30795a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_reserve_blocks() can fail in interesting ways. In neither case is it a
fatal error, but the result can lead to sub-optimal behaviour. Warn to the
syslog if the call fails but otherwise continue.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30784a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Most VN_RELE calls either directly contain a XFS_ITOV or have the
corresponding xfs_inode already in scope. Use the IRELE helper instead of
VN_RELE to clarify the code. With a little more work we can kill VN_RELE
altogether and define IRELE in terms of iput directly.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30710a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
When xfs_mountfs is called by xfs_mount xfs_readsb was called 35 lines
above unconditionally, so there is no need to try to read the superblock
if it's not present. If any other port doesn't have the superblock read at
this point it should just call it directly from it's xfs_mount equivalent.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30603a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Since older kernels may look in the sb_bad_features2 slot for flags,
rather than zeroing it out on fixup, we should make it equal to the
sb_features2 value.
Also, if the ATTR2 flag was not found prior to features2 fixup, it was not
set in the mount flags, so re-check after the fixup so that the current
session will use the feature.
Also fix up the comments to reflect these changes.
SGI-PV: 980085
SGI-Modid: xfs-linux-melb:xfs-kern:30778a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Due to the xfs_dsb_t structure not being 64 bit aligned, the last field of
the on-disk superblock can vary in location This causes problems when the
filesystem gets moved to a different platform, or there is a 32 bit
userspace and 64 bit kernel.
This patch detects the defect at mount time, logs a warning such as:
XFS: correcting sb_features alignment problem
in dmesg and corrects the problem so that everything is OK. it also
blacklists the bad field in the superblock so it does not get used for
something else later on.
SGI-PV: 977636
SGI-Modid: xfs-linux-melb:xfs-kern:30539a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Remove macro-to-small-function indirection from xfs_sb.h, and remove some
which are completely unused.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30528a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
When many hundreds to thousands of threads all try to do simultaneous
transactions and the log is in a tail-pushing situation (i.e. full), we
can get multiple threads walking the AIL list and contending on the AIL
lock.
The AIL push is, in effect, a simple I/O dispatch algorithm complicated by
the ordering constraints placed on it by the transaction subsystem. It
really does not need multiple threads to push on it - even when only a
single CPU is pushing the AIL, it can push the I/O out far faster that
pretty much any disk subsystem can handle.
So, to avoid contention problems stemming from multiple list walkers, move
the list walk off into another thread and simply provide a "target" to
push to. When a thread requires a push, it sets the target and wakes the
push thread, then goes to sleep waiting for the required amount of space
to become available in the log.
This mechanism should also be a lot fairer under heavy load as the waiters
will queue in arrival order, rather than queuing in "who completed a push
first" order.
Also, by moving the pushing to a separate thread we can do more
effectively overload detection and prevention as we can keep context from
loop iteration to loop iteration. That is, we can push only part of the
list each loop and not have to loop back to the start of the list every
time we run. This should also help by reducing the number of items we try
to lock and/or push items that we cannot move.
Note that this patch is not intended to solve the inefficiencies in the
AIL structure and the associated issues with extremely large list
contents. That needs to be addresses separately; parallel access would
cause problems to any new structure as well, so I'm only aiming to isolate
the structure from unbounded parallelism here.
SGI-PV: 972759
SGI-Modid: xfs-linux-melb:xfs-kern:30371a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
These are mostly locking annotations, marking things static, casts where
needed and declaring stuff in header files.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30002a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Refactoring xfs_mountfs() to call sub-functions for logical chunks can
help save a bit of stack, and can make it easier to read this long
function.
The mount path is one of the longest common callchains, easily getting to
within a few bytes of the end of a 4k stack when over lvm, quotas are
enabled, and quotacheck must be done.
With this change on top of the other stack-related changes I've sent, I
can get xfs to survive a normal xfsqa run on 4k stacks over lvm.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29834a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
remove spinlock init abstraction macro in spin.h, remove the callers, and
remove the file. Move no-op spinlock_destroy to xfs_linux.h Cleanup
spinlock locals in xfs_mount.c
SGI-PV: 970382
SGI-Modid: xfs-linux-melb:xfs-kern:29751a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Un-obfuscate XFS_SB_LOCK, remove XFS_SB_LOCK->mutex_lock->spin_lock
macros, call spin_lock directly, remove extraneous cookie holdover from
old xfs code, and change lock type to spinlock_t.
SGI-PV: 970382
SGI-Modid: xfs-linux-melb:xfs-kern:29746a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Currently there is an indirection called ioops in the XFS data I/O path.
Various functions are called by functions pointers, but there is no
coherence in what this is for, and of course for XFS itself it's entirely
unused. This patch removes it instead and significantly reduces source and
binary size of XFS while making maintaince easier.
SGI-PV: 970841
SGI-Modid: xfs-linux-melb:xfs-kern:29737a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
m_growlock only needs plain binary mutex semantics, so use a struct mutex
instead of a semaphore for it.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29512a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Now that struct bhv_vfs doesn't have any members left we can kill it and
go directly from the super_block to the xfs_mount everywhere.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29509a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
All flags are added to xfs_mount's m_flag instead. Note that the 32bit
inode flag was duplicated in both of them, but only cleared in the mount
when it was not nessecary due to the filesystem beeing small enough. Two
flags are still required here - one to indicate the mount option setting,
and one to indicate if it applies or not.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29507a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
vfs_altfsid was just a pointer to mp->m_fixedfsid so we can trivially
replace it with the latter. vfs_fsid also was identical to m_fixedfsid
through rather obfuscated ways so we can kill it as well and simply its
only user.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29506a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Also remove the now dead behavior code.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29505a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Dave Chinner