This patch optimizes the set target port group(STPG) command. During our
testing, we found that it is not optimal to send stpg command every time
the path group switch happens. This patch uses PREF (preferred target port)
bit with combination of flags passed by multipath user level tool to
optimize this behaviour. If PREF bit is set then it issues a STPG command,
otherwise it will let implicit transfer take place.
By default there is no change in the behaviour. User tool needs to pass the
parameter to make this change take effect. Patch has been tested on NetApp
E series storage.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
PREF bit indicates preferred target port group for accessing a logical
unit. This bit is used to optimize the STPG command handling.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Handler expects only one parameter to set the flag ALUA_OPTIMIZE_STPG.
This flag is used to optimize the STPG behaviour. There is no change in
behaviour by default.
For example, to set the flag pass the following parameters from multipath.conf
hardware_handler "2 alua 1"
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a check-condition in scsi_dh_alua handler for a retry.
Sometimes, I have seen attach failing due to this check-condition with
following error messages on NetApp E series storage.
Dec 7 15:31:01 nilgiris kernel: [102979.696673] scsi 3:0:2:9: alua: port group 00 rel port 01
Dec 7 15:31:01 nilgiris kernel: [102979.697082] scsi 3:0:2:9: alua: rtpg failed with 8000002
Dec 7 15:31:01 nilgiris kernel: [102979.697086] scsi 3:0:2:9: alua: rtpg sense code 06/2a/01
Dec 7 15:31:01 nilgiris kernel: [102979.697088] scsi 3:0:2:9: alua: not attached
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If create_singlethread_workqueue() failes, rdac_init should fail too.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: "Moger, Babu" <Babu.Moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All the handlers have now implemented the match function so We don't need to
use scsi_dev_info any more for matching purposes.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch introduces the match function for rdac device handler. Without
this, sometimes handler attach fails during the device_add. Included check for
TPGS bit before proceeding further. The match function was introduced by
commit 6c3633d08a
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch introduces the match function for hp_sw device handler. Included
the check for TPGS bit before proceeding further per Hannes comment. The
match function was introduced by commit
6c3633d08a
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch introduces the match function for emc device handler. Included
check for TPGS bit before proceeding further. The match function was
introduced by commit 6c3633d08a
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
This patch corrects the retry interval for alua rtpg command. Purpose was to retry the commands in seconds.
But that was not happening. Reason is msleep takes argument in milliseconds.
Also added minor text after successful attach.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway. We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch adds one more check-condition for scsi_dh_alua handler. Without
this, the handler attach fails sometimes during the discovery. I have noticed
this with NetApp E-Series storage with alua mode. Also removed some
unnecessary brackets {} for consistency.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds couple more Vendor/Product IDs for RDAC.. There are no
functional changes.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The alua device handler starts the first retry after 10 seconds,
and increases it times 10 for each round.
This leads to an unnecessary delay. This patch modifies it to
start after one second, and increase by a factor of two.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For Target Portal Group IDs occupying the full 2 bytes in the
RTPG response, the following group_id check in the alua_rtpg
routine always fails in scsi_dh_alua.c:
if (h->group_id == (ucp[2] << 8) + ucp[3]) {
This causes the ALUA handler to wrongly identify the AAS of
a specified device as well as incorrectly interpreting the
supported AAS of the target as seen by the following entries
in the /var/log/messages:
"alua: port group 3ea state A supports tousna"
"alua: port group 3e9 state A supports tousna"
This is because 'ucp' is wrongly declared in alua_rtpg as
a character pointer instead of an unsigned character pointer.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Avoid attaching a hardware handler to a device which is
already scheduled for deletion.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When activating a patch we should always update the TPGS state
as it might have changed in between.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixup some kernel-doc comments to reference to the
correct function name.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler assumes that there is one-to-one relation ship
between the host and the controller w.r.t lun. IOW, it does not
support "multiple storage partitions" within a storage.
Example:
HBA1 and HBA2 see lun 0 and 1 in storage A (1)
HBA3 and HBA4 see lun 0 and 1 in storage A (2)
HBA5 and HBA6 see lun 0 and 1 in storage A (3)
luns 0 and 1 in (1), (2) and (3) are totally different.
But, rdac handler treats the lun 0s (and lun 1s) as the same when
sending a mode select to the controller, which is wrong.
This patch makes the rdac hardware handler associate HBA and the
storage w.r.t lun (and not the host itself).
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler uses "Subsystem Identifier" from C4 inquiry page
to uniquely identify a storage. The problem with that is that if any
any of the bytes are non-ascii, subsys_id will all be spaces (hex
0x20). This creates lot of problems especially when there are multiple
rdac storages are connected to the server.
Use "Storage Array Unique Identifier" from C8 inquiry page, which is the
world wide unique identifier for the storage array, to uniquely identify
the storage.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
[SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
[SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
[SCSI] qla2xxx: Clear complete initialization control block.
[SCSI] qla2xxx: Allow an override of the registered maximum LUN.
[SCSI] qla2xxx: Add host number in reset and quiescent message logs.
[SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
[SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
[SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
[SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
[SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
[SCSI] qla2xxx: Fix hang during driver unload when vport is active.
[SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
[SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
[SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
[SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
[SCSI] ipr: Rate limit DMA mapping errors
[SCSI] hpsa: add P2000 to list of shared SAS devices
[SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
[SCSI] hpsa: remove superfluous sleeps around reset code
...
The SCSI ALUA handler currently fails to attach to devices
reporting an UNAVAILABLE/OFFLINE AAS. But given that an
UNAVAILABLE/OFFLINE AAS can transition to other states
like ACTIVE/OPTIMIZED, ACTIVE/NON-OPTIMIZED, etc. as per
SPC4, this ALUA handler behavior should be rectified so
as to attach to devices which also report an
UNAVAILABLE/OFFLINE AAS.
Signed-off-by: Martin George <marting@netapp.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Based on the operating modes, handler decides whether to send mode
select or not. Purpose here is to reduce io-shipping as much as
possible whenever there is an option.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch detects different operating RDAC modes during the
discovery. It also collects the information about the preferred path.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds definitions to support for different operating modes
for LSI rdac storage. Currently, rdac support 3 operation modes.
1. RDAC mode(legacy)
2. AVT mode
3. IOSHIP mode
These definitions are used while activating the path(rdac_activate).
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit db422318cb ([SCSI] scsi_dh:
propagate SCSI device deletion) introduced a regression where the device
reference is not dropped prior to scsi_dh_activate's early return from
the error path.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org # 2.6.38
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is to add Dell MD36xxf array into the RDAC handler device list.
Singed-off-by: Yanqing Liu <Yanqing_Liu@Dell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding MODULE_VERSION for scsi_dh_rdac. This will be helpful sometimes
to get the code level without looking at the code.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
instead of doing sizeof(struct X) it's better to do sizeof(*v) where v
is the variable pointing to struct X.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During one of our testing, we noticed that mode select command sent
from the host did not have the lun_table updated.
Problem is root caused to the way lun table is updated. Lun table
update was done after the call to blk_rq_map_kern is made. This was
causing problem because kernel uses bounce buffer(bio_copy_kern) if
the address is not aligned. The command buffer updated after the
call(blk_rq_map_kern) was not going on the wire. Moved the code to
update the lun_table before the call to fix the problem.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Signed-off-by: Yanling Qi <Yanling.Qi@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in start_stop_endio() rather than blk_put_request() --
blk_finish_request() is called with queue lock already held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Previously we were using strncmp in order to avoid having to include
whitespace in the devlist, but this means "HSV1000" matches a device
list entry that says "HSV100", which is wrong. This patch changes
scsi_dh.c to use scsi_devinfo's matching functions instead, since they
handle these cases correctly.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently NetApp's VID/PID details in the INQUIRY response shows up as
'NETAPP' and 'LUN'. With upcoming scalable SAN ONTAP version on NetApp
controllers, the PID entry alone is being modified to 'LUN C-Mode' (to
distinguish current ONTAP LUNs from scalable ONTAP LUNs).
'LUN' would still suffice for matching 'LUN C-Mode' but best to
explicitly add these new NetApp LUNs to the device list.
Reported-by: Martin George <marting@netapp.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds Promise VTrak devices to the ALUA device handler.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Initialize stpg_endio() 'err' to SCSI_DH_OK and only change it to
SCSI_DH_IO accordingly. This allows the switching of target group state
to be properly reported when no error has occurred.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in stpg_endio() rather than blk_put_request() -- blk_finish_request() is
called with queue lock already held.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
submit_stpg() will always return failure so alua_activate() will report
failure via dm-multipath callback function. Even though the stpg fired
successfuly dm-multipath does not know and always fails to change the
valid path.
By returning SCSI_DH_OK we're now skipping alua_activate()'s call to
activate_complete 'fn'. But this is fine because stpg_endio() will call
it via h->callback_fn().
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, when scsi_dh_activate() returns with an error
(e.g. SCSI_DH_NOSYS) the activate_complete callback is not called and
the error is not propagated to DM mpath.
When a SCSI device attached to a device handler is deleted, userland
processes currently performing I/O on the device will have their I/O
hang forever.
- Set SCSI_DH_NOSYS error when the handler is in the process of being
deleted (e.g. the SCSI device is in a SDEV_CANCEL or SDEV_DEL state).
- Set SCSI_DH_DEV_OFFLINED error when device is in SDEV_OFFLINE state.
- Call the activate_complete callback function directly from
scsi_dh_activate if an error has been set (when either the scsi_dh
internal data has already been deleted or is in the process of being
deleted).
The patch was tested in an iSCSI environment, RDAC H/W handler and
multipath. In the following reproduction process, dd will I/O hang
forever and the only way to release it will be to reboot the machine:
1) Perform I/O on a multipath device:
dd if=/dev/dm-0 of=/dev/zero bs=8k count=1000000 &
2) Delete all slave SCSI devices contained in the mpath device:
I) In an iSCSI environment, the easiest way to do this is by
stopping iSCSI:
/etc/init.d/iscsi stop
II) Another way to delete the devices is by applying the following
bash scriptlet:
dm_devs=$(ls /sys/block/ | grep dm- | xargs)
for dm_dev in $dm_devs; do
devices=$(ls /sys/block/$dm_dev/slaves)
for device in $devices; do
echo 1 > /sys/block/$device/device/delete
done
done
NOTE: when DM mpath's fail_path uses blk_abort_queue this scsi_dh change
isn't strictly required. However, DM mpath's call to blk_abort_queue
will soon be reverted because it has proven to be unsafe due to a race
(between blk_abort_queue and scsi_request_fn) that can lead to list
corruption. Therefore we cannot rely on blk_abort_queue via fail_path,
but even if we could this scsi_dh change is still preferrable.
Signed-off-by: Menny Hamburger <Menny_Hamburger@Dell.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For ALUA we should be handling all states, independent of whether
the mode is explicit or implicit. For 'Transitioning' we should retry
for a certain amount of time; after that we're setting the port
to 'Standby' and return SCSI_DH_RETRY to signal upper layers
a retry is in order here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is to add next generation of Dell iSCSI PowerVault
controller MD36xxi into RDAC device list.
Signed-off-by: Yanqing Liu <Yanqing_Liu@Dell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_get_request sets the cmd_flags, so we should not and do not
need to set them. If we did set them to a different value then
it can cause a oops in the elevator code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Moger, Babu