Commit Graph

287310 Commits

Author SHA1 Message Date
Avinash Patil eb416ad37d mwifiex: correct bitrates advertised to cfg80211
1. Driver and firmware do not support 22Mbps and 72Mbps bitrates.
Remove them from the rate table advertised to cfg80211.

2. First 4 rates from mwifiex_rates table are not valid for
5GHz/A band. Set correct bitrate array's index and no of rates for
ieee80211_supported_band for 5GHz band.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:52 -05:00
Hauke Mehrtens f384b3dddc MIPS: BCM47XX: provide sprom to bcma bus
On SoCs the sprom is often stored in nvram in the flashchip. This patch
registers a sprom fallback callback handler in bcma and provides the
sprom needed for this device.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:51 -05:00
Hauke Mehrtens 019eee2e34 MIPS: BCM47XX: move and extend sprom parsing
Move the sprom parsing from nvram into sprom.c. There are all values
needed for sprom version 1 to 9 read from nvram and there are more
sanity checks added. This is based on the sprom parsing in the open
source part of the Broadcom SDK.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:51 -05:00
Hauke Mehrtens ac78838b65 MIPS: BCM47XX: fix signature of nvram_parse_macaddr
Explicitly enforce an char array of 6 bytes for the mac address.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:51 -05:00
Hauke Mehrtens 44d4b2ae94 MIPS: BCM47XX: return number of written bytes in nvram_getenv
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:50 -05:00
Hauke Mehrtens a027237a56 bcma: add support for sprom not found on the device
On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:50 -05:00
Hauke Mehrtens 1c9351cf21 bcma: export bcma_find_core
This function is needed by the bcm47xx arch code to get the number of
the ieee80211 core.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:50 -05:00
Hauke Mehrtens 52aa63f532 ssb: add some missing sprom attributes
This patch extends the sprom struct to contain all sprom attributes
found in sprom version 1 to 9. This was done accordingly to the open
source part of the Broadcom SDK.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:49 -05:00
Hauke Mehrtens 03a5642b6a ssb: add alpha2
This member contains the country code encoded with two chars

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:49 -05:00
Hauke Mehrtens 3b64e6f905 ssb: fix per path sprom vars
On sprom version 4 and 5 there are 4 values for pa_2g, pa_5gl, pa_5g
and pa_5gh, for sprom version 8 and 9 there are only 3. Make the per
path sprom store also work for older sprom versions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:49 -05:00
Hauke Mehrtens f8f8a660ba ssb: remove 5GHz antenna gain from sprom
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:49 -05:00
Hauke Mehrtens edd8d90b62 ssb: sprom fix some sizes / signedness
Some parts of the sprom struct are bigger than needed.
The leddc and maxpwr values are just 8 bit long and not 16.
rxpo2g and rxpo5g are signed

I got these information for the open source part of the Broadcom SDK
covering sprom version 1 to 9. rxpo2g contained a negative number on my
bcm5354 based device, this cased an error and Broadcom SDK says this is
signed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:48 -05:00
Felix Fietkau 4e0ad2591a ath9k: fix drv_tx_last_beacon on AR9003 by processing beacon tx status
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:48 -05:00
Felix Fietkau 627e67a656 ath9k_hw: enable interrupts for beacon tx completion events
Not doing so could cause the tx status queue to overflow during longer
periods of time without non-beacon tx. These events are also required
for proper drv_tx_last_beacon handling.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:48 -05:00
Felix Fietkau 4286df60ed ath9k: do not call ath9k_hw_txprocdesc on AR9003 outside of the tx tasklet
Since AR9003 uses a global tx status queue, processing tx status outside of
the regular tx tasklet is dangerous and messes up hardware/software
synchronization of tx status events.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:47 -05:00
Felix Fietkau d6157bf780 Revert "ath9k_hw: Fix false tx hung detection in AR9003 chips"
The approach of this change is flawed, as it triggers tx status processing
from more callsites, yet the chips only have one global tx status queue.
Subsequent patches will properly fix the issue that this one tried to address.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:47 -05:00
Amitkumar Karwar a0f6d6caef mwifiex: handle auto authentication mode correctly
When authentication type is configured to NL80211_AUTHTYPE_AUTOMATIC,
driver tries to connect using open mode. The association is failed
if AP is configured in shared mode.

This patch adds code to try association using shared mode as well if
open mode association fails.

Now since we returned exact error code in association response handler
(instead of -1), corresponding changes are done in
mwifiex_process_cmdresp().

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:20:47 -05:00
John W. Linville c288ec614e carl9170: fix breakage from "mac80211: handle non-bufferable MMPDUs correctly"
That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as
IEEE80211_TX_CTL_NO_PS_BUFFER.  Meanwhile, "carl9170: fix frame delivery
if sta is in powersave mode" added a reference to
IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3.  This simple
patch fixes that merge boo-boo.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 15:08:33 -05:00
John W. Linville 8701ff0a88 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-02-29 14:53:21 -05:00
Zefir Kurtisi f4fb4b212d ath9k: decouple RX error checking for DFS
Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.

This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:56 -05:00
Greg Dietsche aef6a62d8b iwlegacy: remove unused enum il4965_calib_enabled_state
Remove the enum il4965_calib_enabled_state because it is not used.

Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:55 -05:00
Greg Dietsche d7b6b6a643 iwlegacy: remove enum iw_calib and related code
Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX.
Remove the function il4965_calib_free_results. It was doing nothing
because IL_CALIB_MAX is zero. Next, remove calib_results from the
il_priv structure and also remove the associated return
type/struct il_calib_result.

Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:55 -05:00
Greg Dietsche 08db1ab7fa iwlegacy: Kconfig: Change Debug Option to be more clear
Since the menuconfig system doesn't indent the debug options
for the 3945 /4965, add some text to make it clear which
debug options are being configured.

Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:55 -05:00
Greg Dietsche 649921499c iwlegacy: Kconfig: Move Debugging Options
Move the debug options so they appear below the 3945 / 4965 options.

Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:54 -05:00
Johannes Berg 02f2f1a951 mac80211: handle non-bufferable MMPDUs correctly
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)

Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:54 -05:00
Amitkumar Karwar 5eb02e44ad mwifiex: remove unnecessary enum MWIFIEX_802_11_WEP_STATUS
Instead of defining an 'enum', we can simply use 'u8' flag for WEP
status. Rename 'wep_status' to 'wep_enabled' to match with
'wpa_enabled' and 'wpa2_enabled'.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:35 -05:00
Amitkumar Karwar 1a907b749c mwifiex: remove redundant scan operation
It should have been removed by commit "mwifiex: use cfg80211 dynamic
scan..." (7c6fa2a843..) after adding code to avoid an extra scan
during association because scan entries are valid for 15 seconds in
cfg80211 stack.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:35 -05:00
Johannes Berg 37ad38887d mac80211: make deauth/disassoc sequence more natural
The association sequence looks (roughly) like
this now:
 * set BSSID
 * set station to EXIST state
 * send auth
 * set station to AUTH state
 * send assoc
 * set station to ASSOC state
 * set BSS info to associated

In contrast, the deauth/disassoc sequence is
the other way around:
 * clear BSSID/BSS info state
 * remove station
 * send deauth/disassoc
(in some cases the last two steps are reversed.)

This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
 * send deauth/disassoc
 * flush
 * remove station
 * clear BSSID/BSS info state

At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:34 -05:00
Johannes Berg 02d83e60b9 mac80211: fix ieee80211_set_disassoc() sending DelBA
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:34 -05:00
Johannes Berg 5fef7dbcad mac80211: dont call cfg80211 from ieee80211_send_deauth_disassoc
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:34 -05:00
Johannes Berg 63c9c5e77c cfg80211: remove cookies from callbacks
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:33 -05:00
Stanislav Yakovlev 4d94c157f8 ipw2x00: remove ipw2100_rates_11b[]
It's just a duplicate of ipw2100_bg_rates[].

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:33 -05:00
Florian Fainelli 02f1434d4e zd1211rw: wait between setting hash table and powering radio on
I am running Debian testing kernel 3.1.0-1-amd64, using a 079b:0062 Sagem
XG-76NA 802.11bg stick.

Upon zd1211rw interface
bringup (ifconfig wlan0 up) I get the following timeout:

[  950.330573] zd1211rw 1-3:1.0: phy2
[  955.108510] zd1211rw 1-3:1.0: firmware version 4725
[  955.148532] zd1211rw 1-3:1.0: zd1211b chip 079b:0062 v4810 high 00-19-70
AL2230_RF pa0 g--NS
[snip]
[  955.204072] zd1211rw 1-3:1.0: error ioread32(CR_REG1): -110

A second ifconfig wlan0 up brings the interface up without problems.

After a bit more debugging, the call trace is the following:

[10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error
ioread32(CR_REG1): -110
[10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs
[10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on

Adding a 10 milliseconds delay between the call to set_mc_hash() and
zd_chip_switch_radio_on() allows successful interface bringups in all
cases and matches what the vendor driver did.

Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:32 -05:00
Amitkumar Karwar 00f157b497 mwifiex: reset encryption mode flag before association
Recent commit
"mwifiex: clear previous security setting during association"
fixes association failure problems observed in some corner cases
by clearing previous security setting before each association.

We should reset encryption mode flag as well. This patch takes care
of it.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 13:08:52 -05:00
Christian Lamparter 9926a67557 carl9170: fix frame delivery if sta is in powersave mode
Nicolas Cavallari discovered that carl9170 has some
serious problems delivering data to sleeping stations.

It turns out that the driver was not honoring two
important flags (IEEE80211_TX_CTL_POLL_RESPONSE and
IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on
frames that should be sent although the receiving
station is still in powersave mode.

Cc: stable <stable@vger.kernel.org>
Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 13:08:51 -05:00
Nicolas Cavallari 992d52529d carl9170: Fix memory accounting when sta is in power-save mode.
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory.  Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.

This undo the allocation done in the TX path when the station is in
power-save mode.

Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 13:08:51 -05:00
Emmanuel Grumbach 659373d515 iwlwifi: fix IDI compilation
This is a fixup for my:
iwlwifi: kill iwl_bus.h

Please fold them into one patch for upstream

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:57:24 -08:00
Wey-Yi Guy 378911233f iwlwifi: update pci subsystem id
Update the pci subsystem id and product name for 6005 series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:57:17 -08:00
Wey-Yi Guy 259653d86b iwlwifi: one more sku added to 6x35 series
Add new sku to 6x35 series

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:57:11 -08:00
Emmanuel Grumbach e679378dc6 iwlwifi: iwl-trans.h doesn't need all these includes
We can use forward declaration for the relevant struct since they
aren't dereferenced in the header file.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:56:55 -08:00
Emmanuel Grumbach 53476fe11f iwlwifi: document the operational mode
Also add a might_sleep to enforce the context requirements.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:56:46 -08:00
Emmanuel Grumbach 4d660ce52e iwlwifi: remove iwl_reset_traffic_log from shared
It is op_mode related

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:56:39 -08:00
Emmanuel Grumbach 3e6895c50a iwlwifi: remove iwl_print_rx_config_cmd from shared
It is op_mode related

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:56:33 -08:00
Emmanuel Grumbach 36a79223c4 iwlwifi: kill iwl_bus.h
No one needs it any more

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:55:43 -08:00
Emmanuel Grumbach ca77d53484 iwlwifi: eeprom gets transport and not bus
This is temporary, but at least we can now throw the bus away
and move the iwl_pci_{probe,remove} functions.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:27:35 -08:00
Emmanuel Grumbach 90304749c3 iwlwifi: move eeprom defines to iwl-eeprom.c
They don't need to be in iwl-dev.h

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:27:27 -08:00
Emmanuel Grumbach ff6e75cb20 iwlwifi: remove a few dereferences to iwl_priv from the tansport
The transport should not dereference the iwl_priv pointer. Remove a
few of those.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:27:15 -08:00
Emmanuel Grumbach bcb9321c8d iwlwifi: virtualize op_mode's fw_error
Export it as "nic_error" notification, the error handling will be in
the op_mode.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:26:58 -08:00
Emmanuel Grumbach 7120d9894c iwlwifi: virtualize op_mode's set_hw_rf_kill
Export it as "hw_rf_kill" notification.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:26:53 -08:00
Emmanuel Grumbach 02e3835884 iwlwifi: virtualize op_mode's stop/start queue
Export them as "queue_full" and "queue_not_full" notification.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2012-02-27 13:26:47 -08:00