IFC NAND chip select is wrongly mapped to 2 in reg property of
NAND node. Due to this kernel is not able probe NAND flash. Set
chip select to 1 in reg property.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1040D4RDB/T1042D4RDB are Freescale Reference Design Board
which can support T1040/T1042 QorIQ Power
Architecture™ processor respectively
T1040D4RDB/T1042D4RDB board Overview
-------------------------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SGMII
- SATA 2.0
- QSGMII(only for T1040D4RDB)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR4 UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1040/T1042D4RDB board:
-add device tree
-Add entry in corenet_generic.c
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In u-boot, when set the video as console, the name 'vga' is used
as a general name for the video device, during the fdt_fixup_stdout
process, the 'vga' name is used to search in the dtb to setup the
'linux,stdout-path' node. Though the P1022 DIU is not VGA-compatible
device, to meet the 'vga' name used in u-boot, the vga alias node is
added for P1022 in this patch. At the same time, a display alias is
also added so that no other components grow dependencies on the vga
alias node.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A whole lot of bug fixes. Nothing stands out here except the ability to
enable CONFIG_OF on every architecture, and an import of a newer version
of dtc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tm5y
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree updates from Grant Likely:
"A whole lot of bug fixes.
Nothing stands out here except the ability to enable CONFIG_OF on
every architecture, and an import of a newer version of dtc"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (22 commits)
of/irq: Rename "intc_desc" to "of_intc_desc" to fix OF on sh
of/irq: Fix pSeries boot failure
Documentation: DT: Fix a typo in the filename "lantiq,<chip>-pinumx.txt"
of: define of_find_node_by_phandle for !CONFIG_OF
of/address: use atomic allocation in pci_register_io_range()
of: Add vendor prefix for Zodiac Inflight Innovations
dt/fdt: add empty versions of early_init_dt_*_memory_arch
of: clean-up unnecessary libfdt include paths
of: make unittest select OF_EARLY_FLATTREE instead of depend on it
of: make CONFIG_OF user selectable
MIPS: prepare for user enabling of CONFIG_OF
of/fdt: fix argument name and add comments of unflatten_dt_node()
of: return NUMA_NO_NODE from fallback of_node_to_nid()
tps6507x.txt: Remove executable permission
of/overlay: Grammar s/an negative/a negative/
of/fdt: Make fdt blob input parameters of unflatten functions const
of: add helper function to retrive match data
of: Grammar s/property exist/property exists/
of: Move OF flags to be visible even when !CONFIG_OF
scripts/dtc: Update to upstream version 9d3649bd3be245c9
...
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
T1023RDB is a Freescale Reference Design Board that hosts T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC flash on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood: vendor prefix: s/at24/atmel/ and trimmed detailed
board description with too-long lines]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for Freescale T1024/T1023 QorIQ Development System Board.
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood: vendor prefix: s/at24/atmel/ and trimmed detailed
board description with too-long lines]
Signed-off-by: Scott Wood <scottwood@freescale.com>
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood@freescale.com: whitespace fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Change-Id: Ic5f28f7b492b708f00a5ff74dda723ce5e1da0ba
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add eSDHC compatible list for P2041/P3041/P4080/P5020/P5040.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for libfdt/dtc update, add the new fdt specific types.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
The celleb code has seen no actual development for ~7 years.
We (maintainers) have no access to test hardware, and it is highly
likely the code has bit-rotted.
As far as we're aware the hardware was never widely available, and is
certainly no longer available, and no one on the list has shown any
interest in it over the years.
So remove it. If anyone has one and cares please speak up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Hai-Ying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Probably we should have not upstreamed this in the first place
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We use r6 and r7 for epapr boot, but the current pre-C init will clobber
both of these.
This change does a simple replacement, of r6 -> r12 and r7 -> r13, so
that we hit platform init with these registers intact.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, a 64-bit little-endian zImage.epapr won't boot in epapr mode,
as we never return from platform_init.
Before entering C, we initialise our stack by setting r1 16 bytes below
the end of the _bss_stack:
stwu r0,-16(r1) /* establish a stack frame */
However, the called function will save the caller's lr in the caller's
frame's lr save area, at -16(r1) to -32(r1).
This means that writes to the fdt variable will corrupt the saved link
register:
0000000020c06018 l O .bss 0000000000001000 _bss_stack
0000000020c07018 l O .bss 0000000000000008 fdt
We'll need at least 32 bytes in the initial stack frame, to handle the
LR save area. We bump this to 112 bytes, as that'll be the max required
by ABIv1.
Thanks to Alistair Popple for debugging help.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We'll likely be entering the zImage.epapr as BE, so include the pseries
implementation of _zimage_start, which adds the endian fixup magic.
Although the endian fixup won't work on Book III-E machines starting LE,
the current entry point doesn't support LE anyway, so we shouldn't be
breaking anything.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For epapr-style boot, we may be little-endian. This change implements
the proper conversion for fdt*_to_cpu and cpu_to_fdt*. We also need the
full cpu_to_* and *_to_cpu macros for this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that the wrapper supports 64-bit builds, we see warnings when
attempting to cast pointers to int. Use unsigned long instead.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Drop planetcore_set_serial_speed() which had no users since its
inception in commit fec6047047 ("[POWERPC] bootwrapper: Add PlanetCore
firmware support") in 2007.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The $(image-n) variable will never exist, because unset Kconfig options
are '' and not 'n'.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the GPIO address in the device tree to match the documented location.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change-Id: I16e63db731e55a3d60d4e147573c1af8718082d3
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Hai-Ying Wang <Haiying.Wang@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Hai-Ying Wang <Haiying.Wang@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for the Artesyn MVME2500 Single Board Computer.
The MVME2500 is a 6U form factor VME64 computer with:
- A single Freescale QorIQ P2010 CPU
- 1 GB of DDR3 onboard memory
- Three Gigabit Ethernets
- Five 16550 compatible UARTS
- One USB 2.0 port, one SHDC socket and one SATA connector
- One PCI/PCI eXpress Mezzanine Card (PMC/XMC) Slot
- MultiProcessor Interrupt Controller (MPIC)
- A DS1375T Real Time Clock (RTC) and 512 KB of Non-Volatile Memory
- Two 64 KB EEPROMs
- U-Boot in 16 SPI Flash
This patch is based on linux-3.18 and has been boot tested.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit 746c9e9f92 "of/base: Fix PowerPC address parsing hack" limited
the applicability of the workaround whereby a missing ranges is treated
as an empty ranges. This workaround was hiding a bug in the etsec2
device tree nodes, which have children with reg, but did not have
ranges.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Alexander Graf <agraf@suse.de>
Probably we should have not upstreamed this in the first place
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott says:
"Highlights include a bunch of 8xx optimizations, device tree bindings
for Freescale BMan, QMan, and FMan datapath components, misc device tree
updates, and inbound rio window support."
On some platforms a 5 second timeout during boot might be quite long, so
make it configurable. Run the loop at least once to let the user stop
the boot by holding a key pressed. If the timeout is set to 0, don't
wait for input, which can be used as a workaround if the boot hangs on
random data coming in on the serial port.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
[mpe: Changelog wording & whitespace]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Change-Id: If76cd705a01813abe53396c1486bc13c4289ee92
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Change-Id: I25ce24a25862b4ca460164159867abefe00ccdd1
Signed-off-by: Scott Wood <scottwood@freescale.com>
* Run "mtdparts default" on u-boot to create dynamic partitions
* Or use dynamic mtd partition with the help of bootargs in u-boot
Append bootargs with:
"mtdparts=ff800000.flash:1m(nand_uboot),512K(nand_dtb),8m(nand_kernel),-(fs);\
spiff707000.0:1m(spi_uboot),4m(spi_kernel),512k(spi_dtb),-(fs)'"
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
Freescale updates from Scott (27 commits):
"Highlights include DMA32 zone support (SATA, USB, etc now works on 64-bit
FSL kernels), MSI changes, 8xx optimizations and cleanup, t104x board
support, and PrPMC PCI enumeration."
in commit 29f1aff2c (powerpc: Copy bootable images in the default
install script) we changed to copying all the built boot targets based
on the assumption that it's backwards compatible. It turns out that
debian devived installkernel scripts will barf if not given exactly 4
args.
This change reverts make install to just install the vmlinux (we can
change the dfault in a seperate patch) and introduces a new make
zInstall which works with a more flexible installkernel script.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change USB controller version to 2.5 in compatible string for T2080/T2081
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality only
T1042RDB_PI board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1042RDB_PI board:
-add device tree
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1040/T1042RDB is Freescale Reference Design Board.
The board can support both T1040/T1042 QorIQ Power Architecture™ processor.
T1040/T1042RDB board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SGMII
- QSGMII
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1040/T1042 RDB board:
-add device tree
-add entry in Kconfig to build
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change USB controller version to 2.5 in compatible string for T4240
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Jaiprakash Singh