The opening comment mark '/**' is used for kernel-doc comments.
There are certain comments in include/linux/fsl/guts.h which follows this
syntax, but the content inside does not comply with kernel-doc.
E.g., opening comment for "Freecale 85xx and 86xx Global Utilties
register set" follows kernel-doc syntax(i.e., '/**'), but the content
inside does not comply with any kernel-doc specification (function,
struct, etc).
This causes unwelcomed warning from kernel-doc:
"warning: expecting prototype for Freecale 85xx and 86xx Global Utilties register set(). Prototype was for __FSL_GUTS_H__() instead"
Replace all such comment occurrences with general comment format,
i.e. '/*' to pervent kernel-doc from parsing these.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
In virtual machines the device-id range is defined
between 0x10000-0x20000. The reason for using such a
large range is to avoid overlapping with the PCI range.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-13-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ pool handling functions can be used by both DPRC
driver and VFIO. Adapt and export those functions.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-12-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both DPRC driver and VFIO driver use the same initialization code
for the DPRC. Introduced a new function which groups this
initialization code. The function is exported and may be
used by VFIO as well.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-10-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create and export a cleanup function for DPRC. The function
is used by the DPRC driver, but it will be used by the VFIO
driver as well.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-9-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the DPRC scan function is used only by the bus driver.
But the same functionality will be needed by the VFIO driver.
To support this, the dprc scan function was exported and a little
bit adjusted to fit both scenarios. Also the scan mutex initialization
is done when the bus object is created, not in dprc_probe in order
to be used by both VFIO and bus driver.
Similarily dprc_remove_devices is exported to be used by VFIO.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-8-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMAN region is memory mapped, so it should be of type
IORESOURCE_MEM. The region flags bits were wrongly used to
pass additional information. Use the bus specific bits for
this purpose.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-5-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is required for vfio-fsl-mc meta driver to successfully bind
layerscape container devices for device passthrough. This patch adds
a mechanism to allow a layerscape device to specify a driver rather than
a layerscape driver provide a device match.
Example to allow a device (dprc.1) to specifically bind
with driver (vfio-fsl-mc):-
- echo vfio-fsl-mc > /sys/bus/fsl-mc/devices/dprc.1/driver_override
- echo dprc.1 > /sys/bus/fsl-mc/drivers/fsl_mc_dprc/unbind
- echo dprc.1 > /sys/bus/fsl-mc/drivers/vfio-fsl-mc/bind
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-4-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FIPER3 (fixed interval period pulse generator) is supported on
DPAA2 and ENETC network controller hardware. This patch is to support
it in ptp_qoriq driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
Replace the spinlock that serializes the MC commands with a raw
spinlock. This is needed for the RT kernel because there are MC
commands sent in interrupt context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200717154800.17169-3-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC bus has different types of devices that can be discovered on the
bus. Add the missing device types.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200717154800.17169-2-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x4
[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off
[root@LS1028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.383/0.611/1.051 ms
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x10
[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss
round-trip min/avg/max = 0.301/0.384/1.138 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Output PPS signal on FIPER2 (Fixed Period Interval Pulse) in default
which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto updates from Herbert Xu:
"API:
- Fix out-of-sync IVs in self-test for IPsec AEAD algorithms
Algorithms:
- Use formally verified implementation of x86/curve25519
Drivers:
- Enhance hwrng support in caam
- Use crypto_engine for skcipher/aead/rsa/hash in caam
- Add Xilinx AES driver
- Add uacce driver
- Register zip engine to uacce in hisilicon
- Add support for OCTEON TX CPT engine in marvell"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
crypto: af_alg - bool type cosmetics
crypto: arm[64]/poly1305 - add artifact to .gitignore files
crypto: caam - limit single JD RNG output to maximum of 16 bytes
crypto: caam - enable prediction resistance in HRWNG
bus: fsl-mc: add api to retrieve mc version
crypto: caam - invalidate entropy register during RNG initialization
crypto: caam - check if RNG job failed
crypto: caam - simplify RNG implementation
crypto: caam - drop global context pointer and init_done
crypto: caam - use struct hwrng's .init for initialization
crypto: caam - allocate RNG instantiation descriptor with GFP_DMA
crypto: ccree - remove duplicated include from cc_aead.c
crypto: chelsio - remove set but not used variable 'adap'
crypto: marvell - enable OcteonTX cpt options for build
crypto: marvell - add the Virtual Function driver for CPT
crypto: marvell - add support for OCTEON TX CPT engine
crypto: marvell - create common Kconfig and Makefile for Marvell
crypto: arm/neon - memzero_explicit aes-cbc key
crypto: bcm - Use scnprintf() for avoiding potential buffer overflow
crypto: atmel-i2c - Fix wakeup fail
...
Add a new api that returns Management Complex firmware version
and make the required structure public. The api's first user will be
the caam driver for setting prediction resistance bits.
Signed-off-by: Andrei Botila <andrei.botila@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The alarm function hadn't been supported by PTP clock driver.
The recommended solution PHC + phc2sys + nanosleep provides
best performance. So drop the code of alarm in ptp_qoriq driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within the LS1028A SoC, the register map for the ENETC MDIO controller
is instantiated a few times: for the central (external) MDIO controller,
for the internal bus of each standalone ENETC port, and for the internal
bus of the Felix switch.
Refactoring is needed to support multiple MDIO buses from multiple
drivers. The enetc_hw structure is made an opaque type and a smaller
enetc_mdio_priv is created.
'mdio_base' - MDIO registers base address - is being parameterized, to
be able to work with different MDIO register bases.
The ENETC MDIO bus operations are exported from the fsl-enetc-mdio
kernel object, the same that registers the central MDIO controller (the
dedicated PF). The ENETC main driver has been changed to select it, and
use its exported helpers to further register its private MDIO bus. The
DSA Felix driver will do the same.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export extts_clean_up() function so that dpaa2-ptp
driver is able to reuse it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the newly added fsl_mc_get_endpoint function a fsl-mc driver can
find its associated endpoint (another object at the other link of a MC
firmware link).
The API will be used in the following patch in order to discover the
connected DPMAC object of a DPNI.
Also, the fsl_mc_device_lookup function is made available to the entire
fsl-mc bus driver and not just for the dprc driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several files are/will be using the same #defines to use the Flextimer
module. Regroup them in a common file.
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
The export of fsl_guts_get_svr() is a left-over, it's currently used
only internally and users needing SoC information should use the generic
soc_device infrastructure.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:
Before:
text data bss dec hex filename
12596 2160 64 14820 39e4 drivers/ptp/ptp_qoriq.o
After:
text data bss dec hex filename
12567 2160 64 14791 39c7 drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1588 timer on eTSEC Ethernet controller uses different
register memory map with DPAA Ethernet controller.
Now the new ENETC Ethernet controller uses same reigster
memory map with DPAA. To support ENETC, let's use register
memory map of DPAA/ENETC in default.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is QorIQ 1588 timer IP block on the new ENETC Ethernet
controller. However it uses little endian mode which is different
with before. This patch is to add little endian support for the
driver by using "little-endian" dts node property.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved QorIQ PTP clock initialization/free into new functions
ptp_qoriq_init()/ptp_qoriq_free(). These functions could also
be reused by ENETC PTP drvier which is a PCI driver for same
1588 timer IP block.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to make functions of ptp operations global,
so that ENETC PTP driver which is a PCI driver for same
1588 timer IP block could reuse them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Strings containing "ptp_qoriq" or "qoriq_ptp" which were used for
structure/function names were complained by users. Let's just use
the unique "ptp_qoriq" to make these names more consistent.
This patch is just to unify the names using "ptp_qoriq". It hasn't
changed any functions.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add debugfs support for ptp_qoriq. Current debugfs
supports to control fiper1/fiper2 loopback mode. If the loopback mode
is enabled, the fiper1/fiper2 pulse is looped back into trigger1/
trigger2 input. This is very useful for validating hardware and driver
without external hardware. Below is an example to enable fiper1 loopback.
echo 1 > /sys/kernel/debug/2d10e00.ptp_clock/fiper1-loopback
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The external trigger stamp FIFO was introduced as a new feature
for QorIQ 1588 timer IP block. This patch is to support it by
adding a new dts property "fsl,extts-fifo". Any QorIQ 1588 timer
supporting this feature is required to add this property in its
dts node.
In addition, the FIFO should be cleaned up before enabling external
trigger interrupts. Otherwise, there will be interrupts immediately
just after enabling external trigger interrupts.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocatable devices can be acquired by drivers on the fsl-mc bus using
the fsl_mc_portal_allocate or fsl_mc_object_allocate functions. Add a
device link between the consumer device and the supplier device so that
proper resource management is achieved.
Also, adding a link between these devices ensures that a proper unbind
order is respected (ie before the supplier device is unbound from its
respective driver all consumer devices will be notified and unbound
first).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Both the header and the command parameters of the fsl_mc_command are
64-bit little-endian words. Use the appropriate type to explicitly
specify their endianness.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates bring:
- Debugfs support for the Intel VT-d driver. When enabled, it
now also exposes some of its internal data structures to
user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing
and fast-path iova allocation code. This is expected to be a
major performance improvement, as this allocation path scales
a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=q1HJ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Debugfs support for the Intel VT-d driver.
When enabled, it now also exposes some of its internal data
structures to user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing and fast-path
iova allocation code.
This is expected to be a major performance improvement, as this
allocation path scales a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
* tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (39 commits)
iommu/arm-smmu-v3: Remove unnecessary wrapper function
iommu/arm-smmu-v3: Add SPDX header
iommu/amd: Add default branch in amd_iommu_capable()
dt-bindings: iommu: ipmmu-vmsa: Add r8a7744 support
iommu/amd: Move iommu_init_pci() to .init section
iommu/arm-smmu: Support non-strict mode
iommu/io-pgtable-arm-v7s: Add support for non-strict mode
iommu/arm-smmu-v3: Add support for non-strict mode
iommu/io-pgtable-arm: Add support for non-strict mode
iommu: Add "iommu.strict" command line option
iommu/dma: Add support for non-strict mode
iommu/arm-smmu: Ensure that page-table updates are visible before TLBI
iommu/arm-smmu-v3: Implement flush_iotlb_all hook
iommu/arm-smmu-v3: Avoid back-to-back CMD_SYNC operations
iommu/arm-smmu-v3: Fix unexpected CMD_SYNC timeout
iommu/io-pgtable-arm: Fix race handling in split_blk_unmap()
iommu/arm-smmu-v3: Fix a couple of minor comment typos
iommu: Fix a typo
iommu: Remove .domain_{get,set}_windows
iommu: Tidy up window attributes
...
Implement bus specific support for the fsl-mc bus including
registering arm_smmu_ops and bus specific device add operations.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch is to support automatic configuration for ptp timer.
If required ptp dts properties are not provided, driver could
try to calculate a set of default configurations to initialize
the ptp timer. This makes the driver work for many boards which
don't have the required ptp dts properties in current kernel.
Also the users could set dts properties by themselves according
to their requirement.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to support DPAA (Data Path Acceleration Architecture)
1588 timer by adding "fsl,fman-ptp-timer" compatible, sharing
interrupt with FMan, adding FSL_DPAA_ETH dependency, and fixing
up register offset.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move some definitions in ptp_qoriq.c
to the header file.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "struct mc_command" is a very generic name for a global
kernel structure. Change its name in "struct fsl_mc_command".
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aditya Srivastava