This path replaces physically contiguous memory arrays
allocated using kmalloc_array() with flexible arrays.
This enables to avoid memory allocation failures on the
systems under a memory stress.
Signed-off-by: Oleg Babin <obabin@virtuozzo.com>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces wrappers for accessing in/out streams indirectly.
This will enable to replace physically contiguous memory arrays
of streams with flexible arrays (or maybe any other appropriate
mechanism) which do memory allocation on a per-page basis.
Signed-off-by: Oleg Babin <obabin@virtuozzo.com>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove blank line at EOF and trailing whitespace.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b6c5734db0 ("sctp: fix the handling of ICMP Frag Needed
for too small MTUs"), sctp_transport_update_pmtu would refetch pathmtu
from the dst and set it to transport's pathmtu without any check.
The new pathmtu may be lower than MINSEGMENT if the dst is obsolete and
updated by .get_dst() in sctp_transport_update_pmtu. In this case, it
could have a smaller MTU as well, and thus we should validate it
against MINSEGMENT instead.
Syzbot reported a warning in sctp_mtu_payload caused by this.
This patch refetches the pathmtu by calling sctp_dst_mtu where it does
the check against MINSEGMENT.
v1->v2:
- refetch the pathmtu by calling sctp_dst_mtu instead as Marcelo's
suggestion.
Fixes: b6c5734db0 ("sctp: fix the handling of ICMP Frag Needed for too small MTUs")
Reported-by: syzbot+f0d9d7cba052f9344b03@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport with illegal flowlabel should not be allowed to send
packets. Other transport protocols already denies this.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct sockaddr_in6 has the member sin6_flowinfo that includes the
ipv6 flowlabel, it should also support for setting flowlabel when
adding a transport whose ipaddr is from userspace.
Note that addrinfo in sctp_sendmsg is using struct in6_addr for
the secondary addrs, which doesn't contain sin6_flowinfo, and
it needs to copy sin6_flowinfo from the primary addr.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spp_ipv6_flowlabel and spp_dscp are added in sctp_paddrparams in
this patch so that users could set sctp_sock/asoc/transport dscp
and flowlabel with spp_flags SPP_IPV6_FLOWLABEL or SPP_DSCP by
SCTP_PEER_ADDR_PARAMS , as described section 8.1.12 in RFC6458.
As said in last patch, it uses '| 0x100000' or '|0x1' to mark
flowlabel or dscp is set, so that their values could be set
to 0.
Note that to guarantee that an old app built with old kernel
headers could work on the newer kernel, the param's check in
sctp_g/setsockopt_peer_addr_params() is also improved, which
follows the way that sctp_g/setsockopt_delayed_ack() or some
other sockopts' process that accept two types of params does.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like some other per transport params, flowlabel and dscp are added
in transport, asoc and sctp_sock. By default, transport sets its
value from asoc's, and asoc does it from sctp_sock. flowlabel
only works for ipv6 transport.
Other than that they need to be passed down in sctp_xmit, flow4/6
also needs to set them before looking up route in get_dst.
Note that it uses '& 0x100000' to check if flowlabel is set and
'& 0x1' (tos 1st bit is unused) to check if dscp is set by users,
so that they could be set to 0 by sockopt in next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is actually already supported by sk->sk_reuse which can be
set by socket level opt SO_REUSEADDR. But it's not working exactly as
RFC6458 demands in section 8.1.27, like:
- This option only supports one-to-one style SCTP sockets
- This socket option must not be used after calling bind()
or sctp_bindx().
Besides, SCTP_REUSE_PORT sockopt should be provided for user's programs.
Otherwise, the programs with SCTP_REUSE_PORT from other systems will not
work in linux.
To separate it from the socket level version, this patch adds 'reuse' in
sctp_sock and it works pretty much as sk->sk_reuse, but with some extra
setup limitations that are needed when it is being enabled.
"It should be noted that the behavior of the socket-level socket option
to reuse ports and/or addresses for SCTP sockets is unspecified", so it
leaves SO_REUSEADDR as is for the compatibility.
Note that the name SCTP_REUSE_PORT is somewhat confusing, as its
functionality is nearly identical to SO_REUSEADDR, but with some
extra restrictions. Here it uses 'reuse' in sctp_sock instead of
'reuseport'. As for sk->sk_reuseport support for SCTP, it will be
added in another patch.
Thanks to Neil to make this clear.
v1->v2:
- add sctp_sk->reuse to separate it from the socket level version.
v2->v3:
- improve changelog according to Marcelo's suggestion.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to the use of rhashtables in net namespaces,
rhashtable.h is included in lots of the kernel,
so a small changes can required a large recompilation.
This makes development painful.
This patch splits out rhashtable-types.h which just includes
the major type declarations, and does not include (non-trivial)
inline code. rhashtable.h is no longer included by anything
in the include/ directory.
Common include files only include rhashtable-types.h so a large
recompilation is only triggered when that changes.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is incrementing SctpFragUsrMsgs when the user message size
is of the exactly same size as the maximum fragment size, which is wrong.
The fix is to increment it only when user message is bigger than the
maximum fragment size.
Fixes: bfd2e4b873 ("sctp: refactor sctp_datamsg_from_user")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Now sctp GSO uses skb_gro_receive() to append the data into head
skb frag_list. However it actually only needs very few code from
skb_gro_receive(). Besides, NAPI_GRO_CB has to be set while most
of its members are not needed here.
This patch is to add sctp_packet_gso_append() to build GSO frames
instead of skb_gro_receive(), and it would avoid many unnecessary
checks and make the code clearer.
Note that sctp will use page frags instead of frag_list to build
GSO frames in another patch. But it may take time, as sctp's GSO
frames may have different size. skb_segment() can only split it
into the frags with the same size, which would break the border
of sctp chunks.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
syzbot reported a rcu_sched self-detected stall on CPU which is caused
by too small value set on rto_min with SCTP_RTOINFO sockopt. With this
value, hb_timer will get stuck there, as in its timer handler it starts
this timer again with this value, then goes to the timer handler again.
This problem is there since very beginning, and thanks to Eric for the
reproducer shared from a syzbot mail.
This patch fixes it by not allowing sctp_transport_timeout to return a
smaller value than HZ/5 for hb_timer, which is based on TCP's min rto.
Note that it doesn't fix this issue by limiting rto_min, as some users
are still using small rto and no proper value was found for it yet.
Reported-by: syzbot+3dcd59a1f907245f891f@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
Now sctp uses inet_dgram_connect as its proto_ops .connect, and the flags
param can't be passed into its proto .connect where this flags is really
needed.
sctp works around it by getting flags from socket file in __sctp_connect.
It works for connecting from userspace, as inherently the user sock has
socket file and it passes f_flags as the flags param into the proto_ops
.connect.
However, the sock created by sock_create_kern doesn't have a socket file,
and it passes the flags (like O_NONBLOCK) by using the flags param in
kernel_connect, which calls proto_ops .connect later.
So to fix it, this patch defines a new proto_ops .connect for sctp,
sctp_inet_connect, which calls __sctp_connect() directly with this
flags param. After this, the sctp's proto .connect can be removed.
Note that sctp_inet_connect doesn't need to do some checks that are not
needed for sctp, which makes thing better than with inet_dgram_connect.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variant of proc_create_data that directly take a seq_file show
callback and deals with network namespaces in ->open and ->release.
All callers of proc_create + single_open_net converted over, and
single_{open,release}_net are removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Variants of proc_create{,_data} that directly take a struct seq_operations
and deal with network namespaces in ->open and ->release. All callers of
proc_create + seq_open_net converted over, and seq_{open,release}_net are
removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Variants of proc_create{,_data} that directly take a struct seq_operations
argument and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
A collection of fixups from previous patches, left for later to not
introduce unnecessary changes while moving code around.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-compute these so the compiler won't reload them (due to
no-strict-aliasing).
Changes since v2:
- Do not replace a return with a break in sctp_outq_flush_data
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this struct we avoid passing lots of variables around and taking care
of updating the current transport/packet.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an inner one, which tended to be error prone due to the cascading
and it can be replaced by a simple if ().
Rework the outer one so that the actual flush code is not inside it. Now
we first validate if we can or cannot send data, return if not, and then
the flush code.
Suggested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retransmissions may be triggered when in user context, so lets make use
of gfp.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To the new sctp_outq_flush_transports.
Comment on Nagle is outdated and removed. Nagle is performed earlier, while
checking if the chunk fits the packet: if the outq length is not enough to
fill the packet, it returns SCTP_XMIT_DELAY.
So by when it gets to sctp_outq_flush_transports, it has to go through all
enlisted transports.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To the new sctp_outq_flush_data. Again, smaller functions and with well
defined objectives.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames current sctp_outq_flush_rtx to __sctp_outq_flush_rtx
and create a new sctp_outq_flush_rtx, with the code that was on
sctp_outq_flush. Again, the idea is to have functions with small and
defined objectives.
Yes, there is an open-coded path selection in the now sctp_outq_flush_rtx.
That is kept as is for now because it may be very different when we
implement retransmission path selection algorithms for CMT-SCTP.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Named sctp_outq_flush_ctrl and, with that, keep the contexts contained.
One small fix embedded is the reset of one_packet at every iteration.
This allows bundling of some control chunks in case they were preceeded by
another control chunk that cannot be bundled.
Other than this, it has the same behavior.
Changes since v2:
- Fixed panic reported by kbuild test robot if building with
only up to this patch applied, due to bad parameter to
sctp_outq_select_transport and by not initializing packet after
calling sctp_outq_flush_ctrl.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had two spots doing such complex operation and they were very close to
each other, a bit more tailored to here or there.
This patch unifies these under the same function,
sctp_outq_select_transport, which knows how to handle control chunks and
original transmissions (but not retransmissions).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code for generating singletons. It's used only once, but
helps to keep the context contained.
The const variables are to ease the reading of subsequent calls in there.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
In Commit 1f45f78f8e ("sctp: allow GSO frags to access the chunk too"),
it held the chunk in sctp_ulpevent_make_rcvmsg to access it safely later
in recvmsg. However, it also added sctp_chunk_put in fail_mark err path,
which is only triggered before holding the chunk.
syzbot reported a use-after-free crash happened on this err path, where
it shouldn't call sctp_chunk_put.
This patch simply removes this call.
Fixes: 1f45f78f8e ("sctp: allow GSO frags to access the chunk too")
Reported-by: syzbot+141d898c5f24489db4aa@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in error string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp only delays the authentication for the normal cookie-echo
chunk by setting chunk->auth_chunk in sctp_endpoint_bh_rcv(). But
for the duplicated one with auth, in sctp_assoc_bh_rcv(), it does
authentication first based on the old asoc, which will definitely
fail due to the different auth info in the old asoc.
The duplicated cookie-echo chunk will create a new asoc with the
auth info from this chunk, and the authentication should also be
done with the new asoc's auth info for all of the collision 'A',
'B' and 'D'. Otherwise, the duplicated cookie-echo chunk with auth
will never pass the authentication and create the new connection.
This issue exists since very beginning, and this fix is to make
sctp_assoc_bh_rcv() follow the way sctp_endpoint_bh_rcv() does
for the normal cookie-echo chunk to delay the authentication.
While at it, remove the unused params from sctp_sf_authenticate()
and define sctp_auth_chunk_verify() used for all the places that
do the delayed authentication.
v1->v2:
fix the typo in changelog as Marcelo noticed.
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When auth is enabled for cookie-ack chunk, in sctp_inq_pop, sctp
processes auth chunk first, then continues to the next chunk in
this packet if chunk_end + chunk_hdr size < skb_tail_pointer().
Otherwise, it will go to the next packet or discard this chunk.
However, it missed the fact that cookie-ack chunk's size is equal
to chunk_hdr size, which couldn't match that check, and thus this
chunk would not get processed.
This patch fixes it by changing the check to chunk_end + chunk_hdr
size <= skb_tail_pointer().
Fixes: 26b87c7881 ("net: sctp: fix remote memory pressure from excessive queueing")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a duplicate cookie-echo chunk, for case 'D', sctp will
not process the param from this chunk. It means old asoc has nothing
to be updated, and the new temp asoc doesn't have the complete info.
So there's no reason to use the new asoc when creating the cookie-ack
chunk. Otherwise, like when auth is enabled for cookie-ack, the chunk
can not be set with auth, and it will definitely be dropped by peer.
This issue is there since very beginning, and we fix it by using the
old asoc instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a duplicate cookie-echo chunk, for case 'A' and 'B',
after sctp_process_init for the new asoc, if auth is enabled for the
cookie-ack chunk, the active key should also be initialized.
Otherwise, the cookie-ack chunk made later can not be set with auth
shkey properly, and a crash can even be caused by this, as after
Commit 1b1e0bc994 ("sctp: add refcnt support for sh_key"), sctp
needs to hold the shkey when making control chunks.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea is quite similar to the old functions, but note that the _fixed
function wasn't "fixed" as in that it would generate a packet with a fixed
size, but rather limited/bounded to PMTU.
Also, now with sctp_mtu_payload(), we have a more accurate limit.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And do so if the skb doesn't have enough space for the payload.
This is a preparation for the next patch.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6458 Section 8.1.16 says that setting MAXSEG as 0 means that the user
is not limiting it, and not that it should set to the *current* maximum,
as we are doing.
This patch thus allow setting it as 0, effectively removing the user
limit.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting SCTP_MAXSEG sock option, it should consider which kind of
data chunk is being used if the asoc is already available, so that the
limit better reflect reality.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_sendmsg() could trigger PMTU updates even when PMTU_DISABLED was
set, as pmtu_pending could be set unconditionally during icmp handling
if the socket was in use by the application.
This patch fixes it by checking for PMTU_DISABLED when handling such
deferred updates.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_transport_route currently is very similar to sctp_transport_pmtu plus
a few other bits.
This patch reuses sctp_transport_pmtu in sctp_transport_route and removes
the duplicated code.
Also, as all calls to sctp_transport_route were forcing the dst release
before calling it, let's just include such release too.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are now keeping the MTU information synced between asoc, transport
and dst, which makes the check at sctp_packet_config() not needed
anymore. As it was the sole caller to this function, lets remove it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which makes sure that the MTU respects the minimum value of
SCTP_DEFAULT_MINSEGMENT and that it is correctly aligned.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and avoid the open-coded versions of it.
Now sctp_datamsg_from_user can just re-use asoc->frag_point as it will
always be updated.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When given a MTU, this function calculates how much payload we can carry
on it. Without a MTU, it calculates the amount of header overhead we
have.
So that when we have extra overhead, like the one added for IP options
on SELinux patches, it is easier to handle it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All changes to asoc PMTU should now go through this wrapper, making it
easier to track them and to do other actions upon it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Xin Long, the if() here is always true as PMTU can never
be 0.
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was only one case that sctp_assoc_add_peer couldn't handle, which
is when SPP_PMTUD_DISABLE is set and pathmtu not initialized.
So add this situation to sctp_transport_route and reuse what was
already in there.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a duplicate cookie-echo chunk, sctp moves the new
temp asoc's stream out/in into the old asoc, and later frees this
new temp asoc.
But now after this move, the new temp asoc's stream->outcnt is not
cleared while stream->out is set to NULL, which would cause a same
crash as the one fixed in Commit 79d0895140 ("sctp: fix error
path in sctp_stream_init") when freeing this asoc later.
This fix is to clear this outcnt in sctp_stream_update.
Fixes: f952be79ce ("sctp: introduce struct sctp_stream_out_ext")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sctp ipv6 socket also supports v4 addrs, it's possible to
compare two v4 addrs in pf v6 .cmp_addr, sctp_inet6_cmp_addr.
However after Commit 1071ec9d45 ("sctp: do not check port in
sctp_inet6_cmp_addr"), it no longer calls af1->cmp_addr, which
in this case is sctp_v4_cmp_addr, but calls __sctp_v6_cmp_addr
where it handles them as two v6 addrs. It would cause a out of
bounds crash.
syzbot found this crash when trying to bind two v4 addrs to a
v6 socket.
This patch fixes it by adding the process for two v4 addrs in
sctp_inet6_cmp_addr.
Fixes: 1071ec9d45 ("sctp: do not check port in sctp_inet6_cmp_addr")
Reported-by: syzbot+cd494c1dd681d4d93ebb@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit 4f00878126 ("sctp: apply rhashtable api to send/recv
path"), there's no place using sctp_assoc_is_match, so remove it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently written as:
if (!tchunk->tsn_gap_acked) { [1]
tchunk->tsn_gap_acked = 1;
...
}
if (TSN_lte(tsn, sack_ctsn)) {
if (!tchunk->tsn_gap_acked) {
/* SFR-CACC processing */
...
}
}
Which causes the SFR-CACC processing on ack reception to never process,
as tchunk->tsn_gap_acked is always true by then. Block [1] was
moved to that position by the commit marked below.
This patch fixes it by doing SFR-CACC processing earlier, before
tsn_gap_acked is set to true.
Fixes: 31b02e1549 ("sctp: Failover transmitted list on transport delete")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_make_sack() make changes to the asoc and this cast is just
bypassing the const attribute. As there is no need to have the const
there, just remove it and fix the violation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com
Signed-off-by: David S. Miller <davem@davemloft.net>
pf->cmp_addr() is called before binding a v6 address to the sock. It
should not check ports, like in sctp_inet_cmp_addr.
But sctp_inet6_cmp_addr checks the addr by invoking af(6)->cmp_addr,
sctp_v6_cmp_addr where it also compares the ports.
This would cause that setsockopt(SCTP_SOCKOPT_BINDX_ADD) could bind
multiple duplicated IPv6 addresses after Commit 40b4f0fd74 ("sctp:
lack the check for ports in sctp_v6_cmp_addr").
This patch is to remove af->cmp_addr called in sctp_inet6_cmp_addr,
but do the proper check for both v6 addrs and v4mapped addrs.
v1->v2:
- define __sctp_v6_cmp_addr to do the common address comparison
used for both pf and af v6 cmp_addr.
Fixes: 40b4f0fd74 ("sctp: lack the check for ports in sctp_v6_cmp_addr")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The sockmap code has to free socket memory on close if there is
corked data, from John Fastabend.
2) Tunnel names coming from userspace need to be length validated. From
Eric Dumazet.
3) arp_filter() has to take VRFs properly into account, from Miguel
Fadon Perlines.
4) Fix oops in error path of tcf_bpf_init(), from Davide Caratti.
5) Missing idr_remove() in u32_delete_key(), from Cong Wang.
6) More syzbot stuff. Several use of uninitialized value fixes all
over, from Eric Dumazet.
7) Do not leak kernel memory to userspace in sctp, also from Eric
Dumazet.
8) Discard frames from unused ports in DSA, from Andrew Lunn.
9) Fix DMA mapping and reset/failover problems in ibmvnic, from Thomas
Falcon.
10) Do not access dp83640 PHY registers prematurely after reset, from
Esben Haabendal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vhost-net: set packet weight of tx polling to 2 * vq size
net: thunderx: rework mac addresses list to u64 array
inetpeer: fix uninit-value in inet_getpeer
dp83640: Ensure against premature access to PHY registers after reset
devlink: convert occ_get op to separate registration
ARM: dts: ls1021a: Specify TBIPA register address
net/fsl_pq_mdio: Allow explicit speficition of TBIPA address
ibmvnic: Do not reset CRQ for Mobility driver resets
ibmvnic: Fix failover case for non-redundant configuration
ibmvnic: Fix reset scheduler error handling
ibmvnic: Zero used TX descriptor counter on reset
ibmvnic: Fix DMA mapping mistakes
tipc: use the right skb in tipc_sk_fill_sock_diag()
sctp: sctp_sockaddr_af must check minimal addr length for AF_INET6
net: dsa: Discard frames from unused ports
sctp: do not leak kernel memory to user space
soreuseport: initialise timewait reuseport field
ipv4: fix uninit-value in ip_route_output_key_hash_rcu()
dccp: initialize ireq->ir_mark
net: fix uninit-value in __hw_addr_add_ex()
...
-----BEGIN PGP SIGNATURE-----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=p2Sh
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux updates from Paul Moore:
"A bigger than usual pull request for SELinux, 13 patches (lucky!)
along with a scary looking diffstat.
Although if you look a bit closer, excluding the usual minor
tweaks/fixes, there are really only two significant changes in this
pull request: the addition of proper SELinux access controls for SCTP
and the encapsulation of a lot of internal SELinux state.
The SCTP changes are the result of a multi-month effort (maybe even a
year or longer?) between the SELinux folks and the SCTP folks to add
proper SELinux controls. A special thanks go to Richard for seeing
this through and keeping the effort moving forward.
The state encapsulation work is a bit of janitorial work that came out
of some early work on SELinux namespacing. The question of namespacing
is still an open one, but I believe there is some real value in the
encapsulation work so we've split that out and are now sending that up
to you"
* tag 'selinux-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: wrap AVC state
selinux: wrap selinuxfs state
selinux: fix handling of uninitialized selinux state in get_bools/classes
selinux: Update SELinux SCTP documentation
selinux: Fix ltp test connect-syscall failure
selinux: rename the {is,set}_enforcing() functions
selinux: wrap global selinux state
selinux: fix typo in selinux_netlbl_sctp_sk_clone declaration
selinux: Add SCTP support
sctp: Add LSM hooks
sctp: Add ip option support
security: Add support for SCTP security hooks
netlabel: If PF_INET6, check sk_buff ip header version
The proc file cleanup left a label possibly unused:
net/sctp/protocol.c: In function 'sctp_defaults_init':
net/sctp/protocol.c:1304:1: error: label 'err_init_proc' defined but not used [-Werror=unused-label]
This adds an #ifdef around it to match the respective 'goto'.
Fixes: d47d08c8ca ("sctp: use proc_remove_subtree()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit dae399d7fd ("sctp: hold transport instead of assoc
when lookup assoc in rx path"), it put transport instead of asoc
in sctp_has_association. Variable 'asoc' is not used any more.
So this patch is to remove it, while at it, it also changes the
return type of sctp_has_association to bool, and does the same
for it's caller sctp_endpoint_is_peeled_off.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
use proc_remove_subtree() for subtree removal, both on setup failure
halfway through and on teardown. No need to make simple things
complex...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot/kasan detected a double free in sctp_sendmsg_to_asoc:
BUG: KASAN: use-after-free in sctp_association_free+0x7b7/0x930
net/sctp/associola.c:332
Read of size 8 at addr ffff8801d8006ae0 by task syzkaller914861/4202
CPU: 1 PID: 4202 Comm: syzkaller914861 Not tainted 4.16.0-rc4+ #258
Hardware name: Google Google Compute Engine/Google Compute Engine
01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23c/0x360 mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
sctp_association_free+0x7b7/0x930 net/sctp/associola.c:332
sctp_sendmsg+0xc67/0x1a80 net/sctp/socket.c:2075
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:763
sock_sendmsg_nosec net/socket.c:629 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:639
SYSC_sendto+0x361/0x5c0 net/socket.c:1748
SyS_sendto+0x40/0x50 net/socket.c:1716
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
This was introduced by commit:
f84af33 sctp: factor out sctp_sendmsg_to_asoc from sctp_sendmsg
As the newly refactored function moved the wait_for_sndbuf call to a
point after the association was connected, allowing for peeloff events
to occur, which in turn caused wait_for_sndbuf to return -EPIPE which
was not caught by the logic that determines if an association should be
freed or not.
Fix it the easy way by returning the ordering of
sctp_primitive_ASSOCIATE and sctp_wait_for_sndbuf to the old order, to
ensure that EPIPE will not happen.
Tested by myself using the syzbot reproducers with positive results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: Xin Long <lucien.xin@gmail.com>
Reported-by: syzbot+a4e4112c3aff00c8cfd8@syzkaller.appspotmail.com
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add SCTP_AUTH_NO_AUTH type for AUTHENTICATION_EVENT,
as described in section 6.1.8 of RFC6458.
SCTP_AUTH_NO_AUTH: This report indicates that the peer does not
support SCTP authentication as defined in [RFC4895].
Note that the implementation is quite similar as that of
SCTP_ADAPTATION_INDICATION.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add SCTP_AUTH_FREE_KEY type for AUTHENTICATION_EVENT,
as described in section 6.1.8 of RFC6458.
SCTP_AUTH_FREE_KEY: This report indicates that the SCTP
implementation will no longer use the key identifier specified
in auth_keynumber.
After deactivating a key, it would never be used again, which means
it's refcnt can't be held/increased by new chunks. But there may be
some chunks in out queue still using it. So only when refcnt is 1,
which means no chunk in outqueue is using/holding this key either,
this EVENT would be sent.
When users receive this notification, they could do DEL_KEY sockopt to
remove this shkey, and also tell the peer that this key won't be used
in any chunk thoroughly from now on, then the peer can remove it as
well safely.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add sockopt SCTP_AUTH_DEACTIVATE_KEY, as described in
section 8.3.4 of RFC6458.
This set option indicates that the application will no longer send user
messages using the indicated key identifier.
Note that RFC requires that only deactivated keys that are no longer used
by an association can be deleted, but for the backward compatibility, it
is not to check deactivated when deleting or replacing one sh_key.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add support for SCTP AUTH Information for sendmsg,
as described in section 5.3.8 of RFC6458.
With this option, you can provide shared key identifier used for
sending the user message.
It's also a necessary send info for sctp_sendv.
Note that it reuses sinfo->sinfo_tsn to indicate if this option is
set and sinfo->sinfo_ssn to save the shkey ID which can be 0.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With refcnt support for sh_key, chunks auth sh_keys can be decided
before enqueuing it. Changing the active key later will not affect
the chunks already enqueued.
Furthermore, this is necessary when adding the support for authinfo
for sendmsg in next patch.
Note that struct sctp_chunk can't be grown due to that performance
drop issue on slow cpu, so it just reuses head_skb memory for shkey
in sctp_chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations create and destroy net::sctp::ctl_sock.
Since pernet_operations do not send sctp packets each other,
they look safe to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations have a deal with sysctl, /proc
entries and statistics. Also, there are freeing of
net::sctp::addr_waitq queue and net::sctp::local_addr_list
in exit method. All of them look pernet-divided, and it
seems these items are only interesting for sctp_defaults_ops,
which are safe to be executed in parallel.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return error code -EINVAL in the address len check error handling
case since 'err' can be overwrite to 0 by 'err = sctp_verify_addr()'
in the for loop.
Fixes: 2c0dbaa0c4 ("sctp: add support for SCTP_DSTADDRV4/6 Information for sendmsg")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As well as the basic conversion, I noticed that a lot of the
SCTP code checks gso_type without first checking skb_is_gso()
so I have added that where appropriate.
Also, document the helper.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add support for snd flag SCTP_SENDALL process
in sendmsg, as described in section 5.3.4 of RFC6458.
With this flag, you can send the same data to all the asocs of
this sk once.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add support for Destination IPv4/6 Address options
for sendmsg, as described in section 5.3.9/10 of RFC6458.
With this option, you can provide more than one destination addrs
to sendmsg when creating asoc, like sctp_connectx.
It's also a necessary send info for sctp_sendv.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add support for PR-SCTP Information for sendmsg,
as described in section 5.3.7 of RFC6458.
With this option, you can specify pr_policy and pr_value for user
data in sendmsg.
It's also a necessary send info for sctp_sendv.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_sendmsg_new_asoc and SCTP_ADDR_OVER check is only necessary
when daddr is set, so move them up to if (daddr) statement.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mostly is to:
- rename sinfo_flags as sflags, to make the indents look better, and
also keep consistent with other sctp_sendmsg_xx functions.
- replace new_asoc with bool new, no need to define a pointer here,
as if new_asoc is set, it must be asoc.
- rename the 'out_nounlock:' as 'out', shorter and nicer.
- remove associd, only one place is using it now, just use
sinfo->sinfo_assoc_id directly.
- remove 'cmsgs' initialization in sctp_sendmsg, as it will be done
in sctp_sendmsg_parse.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp_assoc_lookup_paddr can only be called only if daddr has
been set. But if daddr has been set, sctp_endpoint_lookup_assoc
would be done, where it could already have the transport.
So this unnecessary transport looking up should be removed, but
only reset transport as NULL when SCTP_ADDR_OVER is not set for
UDP type socket.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move the codes for trying to get sinfo from
asoc into sctp_sendmsg_update_sinfo.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move the codes for parsing msghdr and checking
sk into sctp_sendmsg_parse.
Note that different from before, 'sinfo' in sctp_sendmsg won't
be NULL any more. It gets the value either from cmsgs->srinfo,
cmsgs->sinfo or asoc. With it, the 'sinfo' and 'fill_sinfo_ttl'
check can be removed from sctp_sendmsg.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move the codes for trying to get daddr from
msg->msg_name into sctp_sendmsg_get_daddr.
Note that after adding 'daddr', 'to' and 'msg_name' can be
deleted.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move the codes for checking sinfo_flags on one asoc
after this asoc has been found into sctp_sendmsg_check_sflags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move the codes for creating a new asoc if
no asoc was found into sctp_sendmsg_new_asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move the codes for checking and sending on
one asoc after this asoc has been found or created into
sctp_sendmsg_to_asoc.
Note that 'err != -ESRCH' check is for the case that asoc is
freed when waiting for tx buffer in sctp_sendmsg_to_asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add security hooks allowing security modules to exercise access control
over SCTP.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Add ip option support to allow LSM security modules to utilise CIPSO/IPv4
and CALIPSO/IPv6 services.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Commit fb23403536 ("sctp: remove the useless check in
sctp_renege_events") forgot to remove another check for
chunk in sctp_renege_events.
Dan found this when doing a static check.
This patch is to remove that check, and also to merge
two checks into one 'if statement'.
Fixes: fb23403536 ("sctp: remove the useless check in sctp_renege_events")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the file comments in stream.c and
stream_interleave.c
v1->v2:
rephrase the comment for stream.c according to Neil's suggestion.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Fixes: 0c3f6f6554 ("sctp: implement make_datafrag for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add the missing file comments for sctp diag file.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove 'sctp_' prefix for diag file, to keep consistent with other
files' names.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the 'if (chunk)' check in sctp_renege_events for idata process,
as all renege commands are generated in sctp_eat_data and it can't be
NULL.
The same thing we already did for common data in sctp_ulpq_renege.
Fixes: 94014e8d87 ("sctp: implement renege_events for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the support for SCTP_CID_I_DATA and SCTP_CID_I_FWD_TSN chunks,
the corresp conversion in sctp_cname should also be added. Otherwise,
in some places, pr_debug will print them as "unknown chunk".
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pr_err in sctp_hash_transport was supposed to report a sctp bug
for using rhashtable/rhlist.
The err '-EEXIST' introduced in Commit cd2b708750 ("sctp: check
duplicate node before inserting a new transport") doesn't belong
to that case.
So just return -EEXIST back without pr_err any kmsg.
Fixes: cd2b708750 ("sctp: check duplicate node before inserting a new transport")
Reported-by: Wei Chen <weichen@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When SCTP makes INIT or INIT_ACK packet the total chunk length
can exceed SCTP_MAX_CHUNK_LEN which leads to kernel panic when
transmitting these packets, e.g. the crash on sending INIT_ACK:
[ 597.804948] skbuff: skb_over_panic: text:00000000ffae06e4 len:120168
put:120156 head:000000007aa47635 data:00000000d991c2de
tail:0x1d640 end:0xfec0 dev:<NULL>
...
[ 597.976970] ------------[ cut here ]------------
[ 598.033408] kernel BUG at net/core/skbuff.c:104!
[ 600.314841] Call Trace:
[ 600.345829] <IRQ>
[ 600.371639] ? sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.436934] skb_put+0x16c/0x200
[ 600.477295] sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.540630] ? sctp_packet_config+0x890/0x890 [sctp]
[ 600.601781] ? __sctp_packet_append_chunk+0x3b4/0xd00 [sctp]
[ 600.671356] ? sctp_cmp_addr_exact+0x3f/0x90 [sctp]
[ 600.731482] sctp_outq_flush+0x663/0x30d0 [sctp]
[ 600.788565] ? sctp_make_init+0xbf0/0xbf0 [sctp]
[ 600.845555] ? sctp_check_transmitted+0x18f0/0x18f0 [sctp]
[ 600.912945] ? sctp_outq_tail+0x631/0x9d0 [sctp]
[ 600.969936] sctp_cmd_interpreter.isra.22+0x3be1/0x5cb0 [sctp]
[ 601.041593] ? sctp_sf_do_5_1B_init+0x85f/0xc30 [sctp]
[ 601.104837] ? sctp_generate_t1_cookie_event+0x20/0x20 [sctp]
[ 601.175436] ? sctp_eat_data+0x1710/0x1710 [sctp]
[ 601.233575] sctp_do_sm+0x182/0x560 [sctp]
[ 601.284328] ? sctp_has_association+0x70/0x70 [sctp]
[ 601.345586] ? sctp_rcv+0xef4/0x32f0 [sctp]
[ 601.397478] ? sctp6_rcv+0xa/0x20 [sctp]
...
Here the chunk size for INIT_ACK packet becomes too big, mostly
because of the state cookie (INIT packet has large size with
many address parameters), plus additional server parameters.
Later this chunk causes the panic in skb_put_data():
skb_packet_transmit()
sctp_packet_pack()
skb_put_data(nskb, chunk->skb->data, chunk->skb->len);
'nskb' (head skb) was previously allocated with packet->size
from u16 'chunk->chunk_hdr->length'.
As suggested by Marcelo we should check the chunk's length in
_sctp_make_chunk() before trying to allocate skb for it and
discard a chunk if its size bigger than SCTP_MAX_CHUNK_LEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leinter@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dst reference count leak in sctp_v4_get_dst() introduced in commit
410f03831 ("sctp: add routing output fallback"):
When walking the address_list, successive ip_route_output_key() calls
may return the same rt->dst with the reference incremented on each call.
The code would not decrement the dst refcount when the dst pointer was
identical from the previous iteration, causing the dst refcnt leak.
Testcase:
ip netns add TEST
ip netns exec TEST ip link set lo up
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dev dummy0 netns TEST
ip link set dev dummy1 netns TEST
ip link set dev dummy2 netns TEST
ip netns exec TEST ip addr add 192.168.1.1/24 dev dummy0
ip netns exec TEST ip link set dummy0 up
ip netns exec TEST ip addr add 192.168.1.2/24 dev dummy1
ip netns exec TEST ip link set dummy1 up
ip netns exec TEST ip addr add 192.168.1.3/24 dev dummy2
ip netns exec TEST ip link set dummy2 up
ip netns exec TEST sctp_test -H 192.168.1.2 -P 20002 -h 192.168.1.1 -p 20000 -s -B 192.168.1.3
ip netns del TEST
In 4.4 and 4.9 kernels this results to:
[ 354.179591] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 364.419674] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 374.663664] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 384.903717] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 395.143724] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 405.383645] unregister_netdevice: waiting for lo to become free. Usage count = 1
...
Fixes: 410f03831 ("sctp: add routing output fallback")
Fixes: 0ca50d12f ("sctp: fix src address selection if using secondary addresses")
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When going through the bind address list in sctp_v6_get_dst() and
the previously found address is better ('matchlen > bmatchlen'),
the code continues to the next iteration without releasing currently
held destination.
Fix it by releasing 'bdst' before continue to the next iteration, and
instead of introducing one more '!IS_ERR(bdst)' check for dst_release(),
move the already existed one right after ip6_dst_lookup_flow(), i.e. we
shouldn't proceed further if we get an error for the route lookup.
Fixes: dbc2b5e9a0 ("sctp: fix src address selection if using secondary addresses for ipv6")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cache objects. This is good, but still leaves a lot of kernel memory
available to be copied to/from userspace in the face of bugs. To further
restrict what memory is available for copying, this creates a way to
whitelist specific areas of a given slab cache object for copying to/from
userspace, allowing much finer granularity of access control. Slab caches
that are never exposed to userspace can declare no whitelist for their
objects, thereby keeping them unavailable to userspace via dynamic copy
operations. (Note, an implicit form of whitelisting is the use of constant
sizes in usercopy operations and get_user()/put_user(); these bypass all
hardened usercopy checks since these sizes cannot change at runtime.)
This new check is WARN-by-default, so any mistakes can be found over the
next several releases without breaking anyone's system.
The series has roughly the following sections:
- remove %p and improve reporting with offset
- prepare infrastructure and whitelist kmalloc
- update VFS subsystem with whitelists
- update SCSI subsystem with whitelists
- update network subsystem with whitelists
- update process memory with whitelists
- update per-architecture thread_struct with whitelists
- update KVM with whitelists and fix ioctl bug
- mark all other allocations as not whitelisted
- update lkdtm for more sensible test overage
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=tzmJ
-----END PGP SIGNATURE-----
Merge tag 'usercopy-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardened usercopy whitelisting from Kees Cook:
"Currently, hardened usercopy performs dynamic bounds checking on slab
cache objects. This is good, but still leaves a lot of kernel memory
available to be copied to/from userspace in the face of bugs.
To further restrict what memory is available for copying, this creates
a way to whitelist specific areas of a given slab cache object for
copying to/from userspace, allowing much finer granularity of access
control.
Slab caches that are never exposed to userspace can declare no
whitelist for their objects, thereby keeping them unavailable to
userspace via dynamic copy operations. (Note, an implicit form of
whitelisting is the use of constant sizes in usercopy operations and
get_user()/put_user(); these bypass all hardened usercopy checks since
these sizes cannot change at runtime.)
This new check is WARN-by-default, so any mistakes can be found over
the next several releases without breaking anyone's system.
The series has roughly the following sections:
- remove %p and improve reporting with offset
- prepare infrastructure and whitelist kmalloc
- update VFS subsystem with whitelists
- update SCSI subsystem with whitelists
- update network subsystem with whitelists
- update process memory with whitelists
- update per-architecture thread_struct with whitelists
- update KVM with whitelists and fix ioctl bug
- mark all other allocations as not whitelisted
- update lkdtm for more sensible test overage"
* tag 'usercopy-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (38 commits)
lkdtm: Update usercopy tests for whitelisting
usercopy: Restrict non-usercopy caches to size 0
kvm: x86: fix KVM_XEN_HVM_CONFIG ioctl
kvm: whitelist struct kvm_vcpu_arch
arm: Implement thread_struct whitelist for hardened usercopy
arm64: Implement thread_struct whitelist for hardened usercopy
x86: Implement thread_struct whitelist for hardened usercopy
fork: Provide usercopy whitelisting for task_struct
fork: Define usercopy region in thread_stack slab caches
fork: Define usercopy region in mm_struct slab caches
net: Restrict unwhitelisted proto caches to size 0
sctp: Copy struct sctp_sock.autoclose to userspace using put_user()
sctp: Define usercopy region in SCTP proto slab cache
caif: Define usercopy region in caif proto slab cache
ip: Define usercopy region in IP proto slab cache
net: Define usercopy region in struct proto slab cache
scsi: Define usercopy region in scsi_sense_cache slab cache
cifs: Define usercopy region in cifs_request slab cache
vxfs: Define usercopy region in vxfs_inode slab cache
ufs: Define usercopy region in ufs_inode_cache slab cache
...
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull misc vfs updates from Al Viro:
"All kinds of misc stuff, without any unifying topic, from various
people.
Neil's d_anon patch, several bugfixes, introduction of kvmalloc
analogue of kmemdup_user(), extending bitfield.h to deal with
fixed-endians, assorted cleanups all over the place..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
alpha: osf_sys.c: use timespec64 where appropriate
alpha: osf_sys.c: fix put_tv32 regression
jffs2: Fix use-after-free bug in jffs2_iget()'s error handling path
dcache: delete unused d_hash_mask
dcache: subtract d_hash_shift from 32 in advance
fs/buffer.c: fold init_buffer() into init_page_buffers()
fs: fold __inode_permission() into inode_permission()
fs: add RWF_APPEND
sctp: use vmemdup_user() rather than badly open-coding memdup_user()
snd_ctl_elem_init_enum_names(): switch to vmemdup_user()
replace_user_tlv(): switch to vmemdup_user()
new primitive: vmemdup_user()
memdup_user(): switch to GFP_USER
eventfd: fold eventfd_ctx_get() into eventfd_ctx_fileget()
eventfd: fold eventfd_ctx_read() into eventfd_read()
eventfd: convert to use anon_inode_getfd()
nfs4file: get rid of pointless include of btrfs.h
uvc_v4l2: clean copyin/copyout up
vme_user: don't use __copy_..._user()
usx2y: don't bother with memdup_user() for 16-byte structure
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 97a6ec4ac0 ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.
A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.
Note that this issue doesn't affect net.git yet.
Fixes: 97a6ec4ac0 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate gso_type during segmentation as SKB_GSO_DODGY sources
may pass packets where the gso_type does not match the contents.
Syzkaller was able to enter the SCTP gso handler with a packet of
gso_type SKB_GSO_TCPV4.
On entry of transport layer gso handlers, verify that the gso_type
matches the transport protocol.
Fixes: 90017accff ("sctp: Add GSO support")
Link: http://lkml.kernel.org/r/<001a1137452496ffc305617e5fe0@google.com>
Reported-by: syzbot+fee64147a25aecd48055@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check in sctp_sockaddr_af is not robust enough to forbid binding a
v4mapped v6 addr on a v4 socket.
The worse thing is that v4 socket's bind_verify would not convert this
v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4
socket bound a v6 addr.
This patch is to fix it by doing the common sa.sa_family check first,
then AF_INET check for v4mapped v6 addrs.
Fixes: 7dab83de50 ("sctp: Support ipv6only AF_INET6 sockets.")
Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit cea0cc80a6 ("sctp: use the right sk after waking up from
wait_buf sleep"), it may change to lock another sk if the asoc has been
peeled off in sctp_wait_for_sndbuf.
However, the asoc's new sk could be already closed elsewhere, as it's in
the sendmsg context of the old sk that can't avoid the new sk's closing.
If the sk's last one refcnt is held by this asoc, later on after putting
this asoc, the new sk will be freed, while under it's own lock.
This patch is to revert that commit, but fix the old issue by returning
error under the old sk's lock.
Fixes: cea0cc80a6 ("sctp: use the right sk after waking up from wait_buf sleep")
Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introducing sctp_stream structure, sctp uses stream->outcnt as the
out stream nums instead of c.sinit_num_ostreams.
However when users use sinit in cmsg, it only updates c.sinit_num_ostreams
in sctp_sendmsg. At that moment, stream->outcnt is still using previous
value. If it's value is not updated, the sinit_num_ostreams of sinit could
not really work.
This patch is to fix it by updating stream->outcnt and reiniting stream
if stream outcnt has been change by sinit in sendmsg.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The autoclose field can be copied with put_user(), so there is no need to
use copy_to_user(). In both cases, hardened usercopy is being bypassed
since the size is constant, and not open to runtime manipulation.
This patch is verbatim from Brad Spengler/PaX Team's PAX_USERCOPY
whitelisting code in the last public patch of grsecurity/PaX based on my
understanding of the code. Changes or omissions from the original code are
mine and don't reflect the original grsecurity/PaX code.
Signed-off-by: David Windsor <dave@nullcore.net>
[kees: adjust commit log]
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
The SCTP socket event notification subscription information need to be
copied to/from userspace. In support of usercopy hardening, this patch
defines a region in the struct proto slab cache in which userspace copy
operations are allowed. Additionally moves the usercopy fields to be
adjacent for the region to cover both.
example usage trace:
net/sctp/socket.c:
sctp_getsockopt_events(...):
...
copy_to_user(..., &sctp_sk(sk)->subscribe, len)
sctp_setsockopt_events(...):
...
copy_from_user(&sctp_sk(sk)->subscribe, ..., optlen)
sctp_getsockopt_initmsg(...):
...
copy_to_user(..., &sctp_sk(sk)->initmsg, len)
This region is known as the slab cache's usercopy region. Slab caches
can now check that each dynamically sized copy operation involving
cache-managed memory falls entirely within the slab's usercopy region.
This patch is modified from Brad Spengler/PaX Team's PAX_USERCOPY
whitelisting code in the last public patch of grsecurity/PaX based on my
understanding of the code. Changes or omissions from the original code are
mine and don't reflect the original grsecurity/PaX code.
Signed-off-by: David Windsor <dave@nullcore.net>
[kees: split from network patch, move struct members adjacent]
[kees: add SCTPv6 struct whitelist, provide usage trace]
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fall-through are expected.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu reported that some sockopt calls could cause the kernel to log
a warning on memory allocation failure if the user supplied a large optlen
value. That is because some of them called memdup_user() without a ceiling
on optlen, allowing it to try to allocate really large buffers.
This patch adds a ceiling by limiting optlen to the maximum allowed that
would still make sense for these sockopt.
Reported-by: Hangbin Liu <haliu@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So replace it with GFP_USER and also add __GFP_NOWARN.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[ 246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512
That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).
As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.
The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.
Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.
Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad391919 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
resulted in a change or not
Changes from v2:
none
See-also: https://lkml.org/lkml/2017/12/22/811
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.
The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.
Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot noticed a NULL pointer dereference panic in sctp_stream_free()
which was caused by an incomplete error handling in sctp_stream_init().
By not clearing stream->outcnt, it made a for() in sctp_stream_free()
think that it had elements to free, but not, leading to the panic.
As suggested by Xin Long, this patch also simplifies the error path by
moving it to the only if() that uses it.
See-also: https://www.spinics.net/lists/netdev/msg473756.html
See-also: https://www.spinics.net/lists/netdev/msg465024.html
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: f952be79ce ("sctp: introduce struct sctp_stream_out_ext")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove SCTP probe module since jprobe has been deprecated.
That function is now replaced by sctp/sctp_probe and
sctp/sctp_probe_path trace-events.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SCTP ACK tracking trace event to trace the changes of SCTP
association state in response to incoming packets.
It is used for debugging SCTP congestion control algorithms,
and will replace sctp_probe module.
Note that this event a bit tricky. Since this consists of 2
events (sctp_probe and sctp_probe_path) so you have to enable
both events as below.
# cd /sys/kernel/debug/tracing
# echo 1 > events/sctp/sctp_probe/enable
# echo 1 > events/sctp/sctp_probe_path/enable
Or, you can enable all the events under sctp.
# echo 1 > events/sctp/enable
Since sctp_probe_path event is always invoked from sctp_probe
event, you can not see any output if you only enable
sctp_probe_path.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch(180d8cd942) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.
Fixes: 180d8cd942 ("foundations of per-cgroup memory pressure controlling.")
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With changes in inet_ files, SCTP state transitions are traced with
inet_sock_set_state tracepoint.
As SCTP state names, i.e. SCTP_SS_CLOSED, SCTP_SS_ESTABLISHED,
have the same value with TCP state names. So the output info still print
the TCP state names, that makes the code easy.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a new type of chunk is added, the corresp conversion in
sctp_cname should be added. Otherwise, in some places, pr_debug
will print it as "unknown chunk".
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when reneging events in sctp_ulpq_renege(), the variable freed
could be increased by a __u16 value twice while freed is of __u16
type. It means freed may overflow at the second addition.
This patch is to fix it by using __u32 type for 'freed', while at
it, also to remove 'if (chunk)' check, as all renege commands are
generated in sctp_eat_data and it can't be NULL.
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last patch for support of stream interleave, after this patch,
users could enable stream interleave by systcl -w net.sctp.intl_enable=1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using idata and doing stream and asoc reset, setting ssn with
0 could only clear the 1st 16 bits of mid.
So to make this work for both data and idata, it sets mid with 0
instead of ssn, and also mid_uo for unordered idata also need to
be cleared, as said in section 2.3.2 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Marcelo said in the stream scheduler patch:
Support for I-DATA chunks, also described in RFC8260, with user message
interleaving is straightforward as it just requires the schedulers to
probe for the feature and ignore datamsg boundaries when dequeueing.
All needs to do is just to ignore datamsg boundaries when dequeueing.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
handle_ftsn is added as a member of sctp_stream_interleave, used to skip
ssn for data or mid for idata, called for SCTP_CMD_PROCESS_FWDTSN cmd.
sctp_handle_iftsn works for ifwdtsn, and sctp_handle_fwdtsn works for
fwdtsn. Note that different from sctp_handle_fwdtsn, sctp_handle_iftsn
could do stream abort pd.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
report_ftsn is added as a member of sctp_stream_interleave, used to
skip tsn from tsnmap, remove old events from reasm or lobby queue,
and abort pd for data or idata, called for SCTP_CMD_REPORT_FWDTSN
cmd and asoc reset.
sctp_report_iftsn works for ifwdtsn, and sctp_report_fwdtsn works
for fwdtsn. Note that sctp_report_iftsn doesn't do asoc abort_pd,
as stream abort_pd will be done when handling ifwdtsn. But when
ftsn is equal with ftsn, which means asoc reset, asoc abort_pd has
to be done.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_ftsn is added as a member of sctp_stream_interleave, used to
validate ssn/chunk type for fwdtsn or mid (message id)/chunk type for
ifwdtsn, called in sctp_sf_eat_fwd_tsn, just as validate_data.
If this check fails, an abort packet will be sent, as said in section
2.3.1 of RFC8260.
As ifwdtsn and fwdtsn chunks have different length, it also defines
ftsn_chunk_len for sctp_stream_interleave to describe the chunk size.
Then it replaces all sizeof(struct sctp_fwdtsn_chunk) with
sctp_ftsnchk_len.
It also adds the process for ifwdtsn in rx path. As Marcelo pointed
out, there's no need to add event table for ifwdtsn, but just share
prsctp_chunk_event_table with fwdtsn's. It would drop fwdtsn chunk
for ifwdtsn and drop ifwdtsn chunk for fwdtsn by calling validate_ftsn
in sctp_sf_eat_fwd_tsn.
After this patch, the ifwdtsn can be accepted.
Note that this patch also removes the sctp.intl_enable check for
idata chunks in sctp_chunk_event_lookup, as it will do this check
in validate_data later.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
generate_ftsn is added as a member of sctp_stream_interleave, used to
create fwdtsn or ifwdtsn chunk according to abandoned chunks, called
in sctp_retransmit and sctp_outq_sack.
sctp_generate_iftsn works for ifwdtsn, and sctp_generate_fwdtsn is
still used for making fwdtsn.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_ifwdtsn_skip, sctp_ifwdtsn_hdr and sctp_ifwdtsn_chunk are used to
define and parse I-FWD TSN chunk format, and sctp_make_ifwdtsn is a
function to build the chunk.
The I-FORWARD-TSN Chunk Format is defined in section 2.3.1 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_setsockopt_reset_streams, it only does the check
optlen < sizeof(*params) for optlen. But it's not enough, as
params->srs_number_streams should also match optlen.
If the streams in params->srs_stream_list are less than stream
nums in params->srs_number_streams, later when dereferencing
the stream list, it could cause a slab-out-of-bounds crash, as
reported by syzbot.
This patch is to fix it by also checking the stream numbers in
sctp_setsockopt_reset_streams to make sure at least it's not
greater than the streams in the list.
Fixes: 7f9d68ac94 ("sctp: implement sender-side procedures for SSN Reset Request Parameter")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unordered idata process is more complicated than unordered data:
- It has to add mid into sctp_stream_out to save the next mid value,
which is separated from ordered idata's.
- To support pd for unordered idata, another mid and pd_mode need to
be added to save the message id and pd state in sctp_stream_in.
- To make unordered idata reasm easier, it adds a new event queue
to save frags for idata.
The patch mostly adds the samilar reasm functions for unordered idata
as ordered idata's, and also adjusts some other codes on assign_mid,
abort_pd and ulpevent_data for idata.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
abort_pd is added as a member of sctp_stream_interleave, used to abort
partial delivery for data or idata, called in sctp_cmd_assoc_failed.
Since stream interleave allows to do partial delivery for each stream
at the same time, sctp_intl_abort_pd for idata would be very different
from the old function sctp_ulpq_abort_pd for data.
Note that sctp_ulpevent_make_pdapi will support per stream in this
patch by adding pdapi_stream and pdapi_seq in sctp_pdapi_event, as
described in section 6.1.7 of RFC6458.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
start_pd is added as a member of sctp_stream_interleave, used to
do partial_delivery for data or idata when datalen >= asoc->rwnd
in sctp_eat_data. The codes have been done in last patches, but
they need to be extracted into start_pd, so that it could be used
for SCTP_CMD_PART_DELIVER cmd as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
renege_events is added as a member of sctp_stream_interleave, used to
renege some old data or idata in reasm or lobby queue properly to free
some memory for the new data when there's memory stress.
It defines sctp_renege_events for idata, and leaves sctp_ulpq_renege
as it is for data.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enqueue_event is added as a member of sctp_stream_interleave, used to
enqueue either data, idata or notification events into user socket rx
queue.
It replaces sctp_ulpq_tail_event used in the other places with
enqueue_event.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ulpevent_data is added as a member of sctp_stream_interleave, used to
do the most process in ulpq, including to convert data or idata chunk
to event, reasm them in reasm queue and put them in lobby queue in
right order, and deliver them up to user sk rx queue.
This procedure is described in section 2.2.3 of RFC8260.
It adds most functions for idata here to do the similar process as
the old functions for data. But since the details are very different
between them, the old functions can not be reused for idata.
event->ssn and event->ppid settings are moved to ulpevent_data from
sctp_ulpevent_make_rcvmsg, so that sctp_ulpevent_make_rcvmsg could
work for both data and idata.
Note that mid is added in sctp_ulpevent for idata, __packed has to
be used for defining sctp_ulpevent, or it would exceeds the skb cb
that saves a sctp_ulpevent variable for ulp layer process.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_data is added as a member of sctp_stream_interleave, used
to validate ssn/chunk type for data or mid (message id)/chunk type
for idata, called in sctp_eat_data.
If this check fails, an abort packet will be sent, as said in
section 2.2.3 of RFC8260.
It also adds the process for idata in rx path. As Marcelo pointed
out, there's no need to add event table for idata, but just share
chunk_event_table with data's. It would drop data chunk for idata
and drop idata chunk for data by calling validate_data in
sctp_eat_data.
As last patch did, it also replaces sizeof(struct sctp_data_chunk)
with sctp_datachk_len for rx path.
After this patch, the idata can be accepted and delivered to ulp
layer.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
assign_number is added as a member of sctp_stream_interleave, used
to assign ssn for data or mid (message id) for idata, called in
sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is,
and sctp_chunk_assign_mid is added for sctp_stream_interleave_1.
This procedure is described in section 2.2.2 of RFC8260.
All sizeof(struct sctp_data_chunk) in tx path is replaced with
sctp_datachk_len, to make it right for idata as well. And also
adjust sctp_chunk_is_data for SCTP_CID_I_DATA.
After this patch, idata can be built and sent in tx path.
Note that if sp strm_interleave is set, it has to wait_connect in
sctp_sendmsg, as asoc intl_enable need to be known after 4 shake-
hands, to decide if it should use data or idata later. data and
idata can't be mixed to send in one asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid hundreds of checks for the different process on I-DATA chunk,
struct sctp_stream_interleave is defined as a group of functions used
to replace the codes in some place where it needs to do different job
according to if the asoc intl_enabled is set.
With these ops, it only needs to initialize asoc->stream.si with
sctp_stream_interleave_0 for normal data if asoc intl_enable is 0,
or sctp_stream_interleave_1 for idata if asoc intl_enable is set in
sctp_stream_init.
After that, the members in asoc->stream.si can be used directly in
some special places without checking asoc intl_enable.
make_datafrag is the first member for sctp_stream_interleave, it's
used to make data or idata frags, called in sctp_datamsg_from_user.
The old function sctp_make_datafrag_empty needs to be adjust some
to fit in this ops.
Note that as idata and data chunks have different length, it also
defines data_chunk_len for sctp_stream_interleave to describe the
chunk size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_idatahdr and sctp_idata_chunk are used to define and parse
I-DATA chunk format, and sctp_make_idata is a function to build
the chunk.
The I-DATA Chunk Format is defined in section 2.1 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
asoc intl_enable will be set when local sp strm_interleave is set
and there's I-DATA chunk in init and init_ack extensions, as said
in section 2.2.1 of RFC8260.
asoc intl_enable indicates all data will be sent as I-DATA chunks.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds intl_enable in asoc and netns, and strm_interleave in
sctp_sock to indicate if stream interleave is enabled and supported.
netns intl_enable would be set via procfs, but that is not added yet
until all stream interleave codes are completely implemented; asoc
intl_enable will be set when doing 4-shakehands.
sp strm_interleave can be set by sockopt SCTP_INTERLEAVING_SUPPORTED
which is also added in this patch. This socket option is defined in
section 4.3.1 of RFC8260.
Note that strm_interleave can only be set by sockopt when both netns
intl_enable and sp frag_interleave are set.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes calling conventions (and simplifies the hell out
the callers). New rules: once struct socket had been passed
to sock_alloc_file(), it's been consumed either by struct file
or by sock_release() done by sock_alloc_file(). Either way
the caller should not do sock_release() after that point.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now for the abandoned chunks in unsent outq, it would just free the chunks.
Because no tsn is assigned to them yet, there's no need to send fwd tsn to
peer, unlike for the abandoned chunks in sent outq.
The problem is when parts of the msg have been sent and the other frags
are still in unsent outq, if they are abandoned/dropped, the peer would
never get this msg reassembled.
So these frags in unsent outq can't be dropped if this msg already has
outstanding frags.
This patch does the check in sctp_chunk_abandoned and
sctp_prsctp_prune_unsent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As rfc3758#section-3.1 demands:
A3) When a TSN is "abandoned", if it is part of a fragmented message,
all other TSN's within that fragmented message MUST be abandoned
at the same time.
Besides, if it couldn't handle this, the rest frags would never get
assembled in peer side.
This patch supports it by adding abandoned flag in sctp_datamsg, when
one chunk is being abandoned, set chunk->msg->abandoned as well. Next
time when checking for abandoned, go checking chunk->msg->abandoned
first.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now outstanding_bytes is only increased when appending chunks into one
packet and sending it at 1st time, while decreased when it is about to
move into retransmit queue. It means outstanding_bytes value is already
decreased for all chunks in retransmit queue.
However sctp_prsctp_prune_sent is a common function to check the chunks
in both transmitted and retransmit queue, it decrease outstanding_bytes
when moving a chunk into abandoned queue from either of them.
It could cause outstanding_bytes underflow, as it also decreases it's
value for the chunks in retransmit queue.
This patch fixes it by only updating outstanding_bytes for transmitted
queue when pruning queues for prsctp prio policy, the same fix is also
needed in sctp_check_transmitted.
Fixes: 8dbdf1f5b0 ("sctp: implement prsctp PRIO policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d04adf1b35 ("sctp: reset owner sk for data chunks on out queues
when migrating a sock") made a mistake that using 'list' as the param of
list_for_each_entry to traverse the retransmit, sacked and abandoned
queues, while chunks are using 'transmitted_list' to link into these
queues.
It could cause NULL dereference panic if there are chunks in any of these
queues when peeling off one asoc.
So use the chunk member 'transmitted_list' instead in this patch.
Fixes: d04adf1b35 ("sctp: reset owner sk for data chunks on out queues when migrating a sock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now each stream sched ops is defined in different .c file and
added into the global ops in another .c file, it uses extern
to make this work.
However extern is not good coding style to get them in and
even make C=2 reports errors for this.
This patch adds sctp_sched_ops_xxx_init for each stream sched
ops in their .c file, then get them into the global ops by
calling them when initializing sctp module.
Fixes: 637784ade2 ("sctp: introduce priority based stream scheduler")
Fixes: ac1ed8b82c ("sctp: introduce round robin stream scheduler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to force SCTP_ERROR_INV_STRM with right type to
fit in sctp_chunk_fail to avoid the sparse error.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing asoc reset, if the sender of the response has already sent some
chunk and increased asoc->next_tsn before the duplicate request comes, the
response will use the old result with an incorrect sender next_tsn.
Better than asoc->next_tsn, asoc->ctsn_ack_point can't be changed after
the sender of the response has performed the asoc reset and before the
peer has confirmed it, and it's value is still asoc->next_tsn original
value minus 1.
This patch sets sender next_tsn for the old result with ctsn_ack_point
plus 1 when processing the duplicate request, to make sure the sender
next_tsn value peer gets will be always right.
Fixes: 692787cef6 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when doing asoc reset, it cleans up sacked and abandoned queues
by calling sctp_outq_free where it also cleans up unsent, retransmit
and transmitted queues.
It's safe for the sender of response, as these 3 queues are empty at
that time. But when the receiver of response is doing the reset, the
users may already enqueue some chunks into unsent during the time
waiting the response, and these chunks should not be flushed.
To void the chunks in it would be removed, it moves the queue into a
temp list, then gets it back after sctp_outq_free is done.
The patch also fixes some incorrect comments in
sctp_process_strreset_tsnreq.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it says in rfc6525#section5.1.4, before sending the request,
C2: The sender has either no outstanding TSNs or considers all
outstanding TSNs abandoned.
Prior to this patch, it tried to consider all outstanding TSNs abandoned
by dropping all chunks in all outqs with sctp_outq_free (even including
sacked, retransmit and transmitted queues) when doing this reset, which
is too aggressive.
To make it work gently, this patch will only allow the asoc reset when
the sender has no outstanding TSNs by checking if unsent, transmitted
and retransmit are all empty with sctp_outq_is_empty before sending
and processing the request.
Fixes: 692787cef6 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the out stream reset in sctp stream reconf could be done even if
the stream outq is not empty. It means that users can not be sure
since which msg the new ssn will be used.
To make this more synchronous, it shouldn't allow to do out stream
reset until these chunks in unsent outq all are sent out.
This patch checks the corresponding stream outqs when sending and
processing the request . If any of them has unsent chunks in outq,
it will return -EAGAIN instead or send SCTP_STRRESET_IN_PROGRESS
back to the sender.
Fixes: 7f9d68ac94 ("sctp: implement sender-side procedures for SSN Reset Request Parameter")
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in stream reconf part there are still some places using magic
number 2 for each stream number length. To make it more readable,
this patch is to replace them with sizeof(__u16).
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_setsockopt_maxseg user_frag or frag_point can be set with
val >= 8 and val <= SCTP_MAX_CHUNK_LEN. But both checks are incorrect.
val >= 8 means frag_point can even be less than SCTP_DEFAULT_MINSEGMENT.
Then in sctp_datamsg_from_user(), when it's value is greater than cookie
echo len and trying to bundle with cookie echo chunk, the first_len will
overflow.
The worse case is when it's value is equal as cookie echo len, first_len
becomes 0, it will go into a dead loop for fragment later on. In Hangbin
syzkaller testing env, oom was even triggered due to consecutive memory
allocation in that loop.
Besides, SCTP_MAX_CHUNK_LEN is the max size of the whole chunk, it should
deduct the data header for frag_point or user_frag check.
This patch does a proper check with SCTP_DEFAULT_MINSEGMENT subtracting
the sctphdr and datahdr, SCTP_MAX_CHUNK_LEN subtracting datahdr when
setting frag_point via sockopt. It also improves sctp_setsockopt_maxseg
codes.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandar Potapenko while testing the kernel with KMSAN and syzkaller
discovered that in some configurations sctp would leak 4 bytes of
kernel stack.
Working with his reproducer I discovered that those 4 bytes that
are leaked is the scope id of an ipv6 address returned by recvmsg.
With a little code inspection and a shrewd guess I discovered that
sctp_inet6_skb_msgname only initializes the scope_id field for link
local ipv6 addresses to the interface index the link local address
pertains to instead of initializing the scope_id field for all ipv6
addresses.
That is almost reasonable as scope_id's are meaniningful only for link
local addresses. Set the scope_id in all other cases to 0 which is
not a valid interface index to make it clear there is nothing useful
in the scope_id field.
There should be no danger of breaking userspace as the stack leak
guaranteed that previously meaningless random data was being returned.
Fixes: 372f525b495c ("SCTP: Resync with LKSCTP tree.")
History-tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when resetting stream, if both in and out flags are set, the info
len can reach:
sizeof(struct sctp_strreset_outreq) + SCTP_MAX_STREAM(65535) +
sizeof(struct sctp_strreset_inreq) + SCTP_MAX_STREAM(65535)
even without duplicated stream no, this value is far greater than the
chunk's max size.
_sctp_make_chunk doesn't do any check for this, which would cause the
skb it allocs is huge, syzbot even reported a crash due to this.
This patch is to check stream reset info len before making reconf
chunk and return EINVAL if the len exceeds chunk's capacity.
Thanks Marcelo and Neil for making this clear.
v1->v2:
- move the check into sctp_send_reset_streams instead.
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dfcb9f4f99 ("sctp: deny peeloff operation on asocs with threads
sleeping on it") fixed the race between peeloff and wait sndbuf by
checking waitqueue_active(&asoc->wait) in sctp_do_peeloff().
But it actually doesn't work, as even if waitqueue_active returns false
the waiting sndbuf thread may still not yet hold sk lock. After asoc is
peeled off, sk is not asoc->base.sk any more, then to hold the old sk
lock couldn't make assoc safe to access.
This patch is to fix this by changing to hold the new sk lock if sk is
not asoc->base.sk, meanwhile, also set the sk in sctp_sendmsg with the
new sk.
With this fix, there is no more race between peeloff and waitbuf, the
check 'waitqueue_active' in sctp_do_peeloff can be removed.
Thanks Marcelo and Neil for making this clear.
v1->v2:
fix it by changing to lock the new sock instead of adding a flag in asoc.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_sendmsg sctp_wait_for_sndbuf could schedule out without
holding sock sk. It means the current asoc can be freed elsewhere,
like when receiving an abort packet.
If the asoc is just created in sctp_sendmsg and sctp_wait_for_sndbuf
returns err, the asoc will be freed again due to new_asoc is not nil.
An use-after-free issue would be triggered by this.
This patch is to fix it by setting new_asoc with nil if the asoc is
already dead when cpu schedules back, so that it will not be freed
again in sctp_sendmsg.
v1->v2:
set new_asoc as nil in sctp_sendmsg instead of sctp_wait_for_sndbuf.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to returnerror code -ENOMEM from the sctp_make_strreset_addstrm()
error handling case instead of 0. 'retval' can be overwritten to 0 after
call sctp_stream_alloc_out().
Fixes: e090abd0d8 ("sctp: factor out stream->out allocation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.
Note after this patch, there still one warning left in
sctp_outq_flush():
sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)
Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
Commit d4d6fb5787 ("sctp: Try not to change a_rwnd when faking a
SACK from SHUTDOWN.") expected to use the peers old rwnd and add
our flight size to the a_rwnd. But with the wrong Endian, it may
not work as well as expected.
So fix it by converting to the right value.
Fixes: d4d6fb5787 ("sctp: Try not to change a_rwnd when faking a SACK from SHUTDOWN.")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian for the port when
coding transport rhashtable patches.
Fixes: 7fda702f93 ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian when coding stream
reconf patches.
Since commit c0d8bab6ae ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.
Fixes: c0d8bab6ae ("sctp: add get and set sockopt for reconf_enable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when migrating sock to another one in sctp_sock_migrate(), it only
resets owner sk for the data in receive queues, not the chunks on out
queues.
It would cause that data chunks length on the sock is not consistent
with sk sk_wmem_alloc. When closing the sock or freeing these chunks,
the old sk would never be freed, and the new sock may crash due to
the overflow sk_wmem_alloc.
syzbot found this issue with this series:
r0 = socket$inet_sctp()
sendto$inet(r0)
listen(r0)
accept4(r0)
close(r0)
Although listen() should have returned error when one TCP-style socket
is in connecting (I may fix this one in another patch), it could also
be reproduced by peeling off an assoc.
This issue is there since very beginning.
This patch is to reset owner sk for the chunks on out queues so that
sk sk_wmem_alloc has correct value after accept one sock or peeloff
an assoc to one sock.
Note that when resetting owner sk for chunks on outqueue, it has to
sctp_clear_owner_w/skb_orphan chunks before changing assoc->base.sk
first and then sctp_set_owner_w them after changing assoc->base.sk,
due to that sctp_wfree and it's callees are using assoc->base.sk.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Konstantin Khorenko