The drain_mr_fqni() function may be called fron uninterruptable
context so convert the msleep() to an mdelay(). Also ensure that
the valid bit is updated while polling.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
If the QMan device was previously initialized make sure all the
frame queues are out of service once all the portals are probed.
This handles the case where the kernel is restarted without the
SoC being reset (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Clean the BMan buffer pools if the device had been initialized
previously. This will ensure a consistent state if the kernel
was soft restarted (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Rework QBMan private memory setup so that the areas are not
zeroed if the device was previously initialized
If the QMan private memory was already initialized skip the PFDR
initialization.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <treding@nvidia.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Handful of fixes/updates including:
1. SCMI v2.0(recently released) support for:
- Performance protocol fast channels
- Reset Management Protocol
2. SCMI infrastructure/core support for recieve(Rx) channels,
asynchronous commands and delayed response
3. Usage of asynchronous commands for clock rate setting and sensor
reading based on the attributes read from the firmware
4. Miscellaneous cleanups(typos, naming alignment with specification,
and SPDX License identifier)
5. Couple of fixes: removal of extra check for invalid length and
additional check to ensure platform/firmware has released shared
memory before using it in OSPM
-----BEGIN PGP SIGNATURE-----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=Rnle
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
ARM SCMI updates/fixes for v5.4
Handful of fixes/updates including:
1. SCMI v2.0(recently released) support for:
- Performance protocol fast channels
- Reset Management Protocol
2. SCMI infrastructure/core support for recieve(Rx) channels,
asynchronous commands and delayed response
3. Usage of asynchronous commands for clock rate setting and sensor
reading based on the attributes read from the firmware
4. Miscellaneous cleanups(typos, naming alignment with specification,
and SPDX License identifier)
5. Couple of fixes: removal of extra check for invalid length and
additional check to ensure platform/firmware has released shared
memory before using it in OSPM
* tag 'scmi-updates-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: (22 commits)
reset: Add support for resets provided by SCMI
firmware: arm_scmi: Add RESET protocol in SCMI v2.0
dt-bindings: arm: Extend SCMI to support new reset protocol
firmware: arm_scmi: Make use SCMI v2.0 fastchannel for performance protocol
firmware: arm_scmi: Add discovery of SCMI v2.0 performance fastchannels
firmware: arm_scmi: Use {get,put}_unaligned_le{32,64} accessors
firmware: arm_scmi: Use asynchronous CLOCK_RATE_SET when possible
firmware: arm_scmi: Drop config flag in clk_ops->rate_set
firmware: arm_scmi: Add asynchronous sensor read if it supports
firmware: arm_scmi: Drop async flag in sensor_ops->reading_get
firmware: arm_scmi: Add support for asynchronous commands and delayed response
firmware: arm_scmi: Add mechanism to unpack message headers
firmware: arm_scmi: Separate out tx buffer handling and prepare to add rx
firmware: arm_scmi: Add receive channel support for notifications
firmware: arm_scmi: Segregate tx channel handling and prepare to add rx
firmware: arm_scmi: Reorder some functions to avoid forward declarations
firmware: arm_scmi: Check if platform has released shmem before using
firmware: arm_scmi: Use the term 'message' instead of 'command'
firmware: arm_scmi: Fix few trivial typos in comments
firmware: arm_scmi: Remove extra check for invalid length message responses
...
Link: https://lore.kernel.org/r/20190814172454.26191-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds documentation of the device tree bindings for GPIOs
on the devices connected via Moxtet bus.
Link: https://lore.kernel.org/r/20190812161118.21476-6-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for interpreting the input and output bits of one
device on Moxtet bus as GPIOs.
This is needed for example by the SFP cage module of Turris Mox.
Link: https://lore.kernel.org/r/20190812161118.21476-5-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add sysfs ABI documentation for the attribute files module_id and
module_name
Add debugfs ABI documentation for reading input from the shift registers
and reading last written output or write output to the shift registers.
Link: https://lore.kernel.org/r/20190812161118.21476-4-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds device tree binding documentation for the Moxtet bus, a bus
via which the different modules connected to the Turris Mox router can
be configured.
Link: https://lore.kernel.org/r/20190812161118.21476-3-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On the Turris Mox router different modules can be connected to the main
CPU board: currently a module with a SFP cage, a module with MiniPCIe
connector, a PCIe pass-through MiniPCIe connector module, a 4-port
switch module, an 8-port switch module, and a 4-port USB3 module.
For example:
[CPU]-[PCIe-pass-through]-[PCIe]-[8-port switch]-[8-port switch]-[SFP]
Each of this modules has an input and output shift register, and these
are connected via SPI to the CPU board.
Via SPI we are able to discover which modules are connected, in which
order, and we can also read some information about the modules (eg.
their interrupt status), and configure them.
From each module 8 bits can be read (of which low 4 bits identify the
module) and 8 bits can be written.
For example from the module with a SFP cage we can read the LOS,
TX-FAULT and MOD-DEF0 signals, while we can write TX-DISABLE and
RATE-SELECT signals.
This driver creates a new bus type, called "moxtet". For each Mox module
it finds via SPI, it creates a new device on the moxtet bus so that
drivers can be written for them.
It also implements a virtual interrupt controller for the modules which
send their interrupt status over the SPI shift register. These modules
do this in addition to sending their interrupt status via the shared
interrupt line. When the shared interrupt is triggered, we read from the
shift register and handle IRQs for all devices which are in interrupt.
The topology of how Mox modules are connected can then be read by
listing /sys/bus/moxtet/devices.
Link: https://lore.kernel.org/r/20190812161118.21476-2-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix a flexible array member definition in the R-Car SYSC driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXUQczwAKCRCKwlD9ZEnx
cKN7AQCqies8aPvDBHhx4TmGi3rAutEcYtvJGpYfEqON2neKIwD8C3/iPd+NUQdH
Q4ulQIhTFkrIXyobb5BrMD3QENygtgA=
=LULc
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.4
- Fix a flexible array member definition in the R-Car SYSC driver.
* tag 'renesas-drivers-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: rcar-sysc: Use [] to denote a flexible array member
Link: https://lore.kernel.org/r/20190802120355.1430-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This tag adds support for the i.MX8MM SRC via the reset-imx7 driver
and for DesignWare IP reset controllers via the reset-simple driver.
A typo in the i.MX8MQ DSI reset definitions is fixed, and the Meson
reset driver and binding headers are updated to SPDX license
identifiers.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXVE2PxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwP2dAQCPcwxmyNt9DeRTcHMsZ/8WpROG
8dNLl6lGJIRHBon+wAD/ZGO7GI3YLgghInSWurSn2w3VjqB9yjrEiYjCOt3LkAg=
=hIhK
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v5.4' of git://git.pengutronix.de/git/pza/linux into arm/drivers
Reset controller changes for v5.4
This tag adds support for the i.MX8MM SRC via the reset-imx7 driver
and for DesignWare IP reset controllers via the reset-simple driver.
A typo in the i.MX8MQ DSI reset definitions is fixed, and the Meson
reset driver and binding headers are updated to SPDX license
identifiers.
* tag 'reset-for-v5.4' of git://git.pengutronix.de/git/pza/linux:
reset: Add DesignWare IP support to simple reset
dt-bindings: Document the DesignWare IP reset bindings
dt-bindings: reset: amlogic,meson8b-reset: update with SPDX Licence identifier
dt-bindings: reset: amlogic,meson-gxbb-reset: update with SPDX Licence identifier
reset: reset-meson: update with SPDX Licence identifier
dt-bindings: reset: Fix typo in imx8mq resets
dt-bindings: reset: imx7: Add support for i.MX8MM
Link: https://lore.kernel.org/r/1565603668.5017.2.camel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Management Interface(SCMI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
Adds support for the resets provided using SCMI protocol for performing
reset management of various devices present on the SoC. Various reset
functionalities are achieved by the means of different ARM SCMI device
operations provided by the ARM SCMI framework.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMIv2.0 adds a new Reset Management Protocol to manage various reset
states a given device or domain can enter. Device(s) that can be
collectively reset through a common reset signal constitute a reset
domain for the firmware.
A reset domain can be reset autonomously or explicitly through assertion
and de-assertion of the signal. When autonomous reset is chosen, the
firmware is responsible for taking the necessary steps to reset the
domain and to subsequently bring it out of reset. When explicit reset is
chosen, the caller has to specifically assert and then de-assert the
reset signal by issuing two separate RESET commands.
Add the basic SCMI reset infrastructure that can be used by Linux
reset controller driver.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMIv2.0 adds a new Reset Management Protocol to manage various reset
states a given device or domain can enter. Extend the existing SCMI
bindings to add reset protocol support by re-using the reset bindings
for both reset providers and consumers.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI v2.0 adds support for "FastChannel" which do not use a message
header as they are specialized for a single message.
Only PERFORMANCE_LIMITS_{SET,GET} and PERFORMANCE_LEVEL_{SET,GET}
commands are supported over fastchannels. As they are optional, they
need to be discovered by PERFORMANCE_DESCRIBE_FASTCHANNEL command.
Further {LIMIT,LEVEL}_SET commands can have optional doorbell support.
Add support for making use of these fastchannels.
Cc: Ionela Voinescu <Ionela.Voinescu@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Quentin Perret <Quentin.Perret@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI v2.0 adds support for "FastChannel", a lightweight unidirectional
channel that is dedicated to a single SCMI message type for controlling
a specific platform resource. They do not use a message header as they
are specialized for a single message.
Only PERFORMANCE_LIMITS_{SET,GET} and PERFORMANCE_LEVEL_{SET,GET}
commands are supported over fastchannels. As they are optional, they
need to be discovered by PERFORMANCE_DESCRIBE_FASTCHANNEL command.
Further {LIMIT,LEVEL}_SET commands can have optional doorbell support.
Add support for discovery of these fastchannels.
Cc: Ionela Voinescu <Ionela.Voinescu@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Quentin Perret <Quentin.Perret@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Instead of type-casting the {tx,rx}.buf all over the place while
accessing them to read/write __le{32,64} from/to the firmware, let's
use the existing {get,put}_unaligned_le{32,64} accessors to hide all
the type cast ugliness.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.
Tracking the current count of pending asynchronous clock set rate
requests, we can decide if the incoming/new request for clock set rate
can be handled asynchronously or not until the maximum limit is
reached.
Cc: linux-clk@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.
In order to add that support, let's drop the config flag passed to
clk_ops->rate_set and handle the asynchronous requests dynamically.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. We can read that flag and use asynchronous
reads for any sensors with that attribute set.
Let's use the new scmi_do_xfer_with_response to support asynchronous
sensor reads.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. Ideally we should be able to read that flag
and use asynchronous reads for any sensors with that attribute set.
In order to add that support, let's drop the async flag passed to
sensor_ops->reading_get and dynamically switch between sync and async
flags based on the attributes as provided by the firmware.
Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Messages that are sent to platform, also known as commands and can be:
1. Synchronous commands that block the channel until the requested work
has been completed. The platform responds to these commands over the
same channel and hence can't be used to send another command until the
previous command has completed.
2. Asynchronous commands on the other hand, the platform schedules the
requested work to complete later in time and returns almost immediately
freeing the channel for new commands. The response indicates the success
or failure in the ability to schedule the requested work. When the work
has completed, the platform sends an additional delayed response message.
Using the same transmit buffer used for sending the asynchronous command
even for the delayed response corresponding to it simplifies handling of
the delayed response. It's the caller of asynchronous command that is
responsible for allocating the completion flag that scmi driver can
complete to indicate the arrival of delayed response.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to identify the message type when a response arrives, we need
a mechanism to unpack the message header similar to packing. Let's
add one.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently we pre-allocate transmit buffers only and use the first free
slot in that pre-allocated buffer for transmitting any new message that
are generally originated from OS to the platform firmware.
Notifications or the delayed responses on the other hand are originated
from the platform firmware and consumes by the OS. It's better to have
separate and dedicated pre-allocated buffers to handle the notifications.
We can still use the transmit buffers for the delayed responses.
In addition, let's prepare existing scmi_xfer_{get,put} for acquiring
and releasing a slot to identify the right(tx/rx) buffers.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With scmi_mbox_chan_setup enabled to identify and setup both Tx and Rx,
let's consolidate setting up of both the channels under the function
scmi_mbox_txrx_setup.
Since some platforms may opt not to support notifications or delayed
response, they may not need support for Rx. Hence Rx is optional and
failure of setting one up is not considered fatal.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The transmit(Tx) channels are specified as the first entry and the
receive(Rx) channels are the second entry as per the device tree
bindings. Since we currently just support Tx, index 0 is hardcoded at
all required callsites.
In order to prepare for adding Rx support, let's remove those hardcoded
index and add boolean parameter to identify Tx/Rx channels when setting
them up.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Re-shuffling few functions to keep definitions and their usages close.
This is also needed to avoid too many unnecessary forward declarations
while adding new features(delayed response and notifications).
Keeping this separate to avoid mixing up of these trivial change that
doesn't affect functionality into the ones that does.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Sometimes platfom may take too long to respond to the command and OS
might timeout before platform transfer the ownership of the shared
memory region to the OS with the response.
Since the mailbox channel associated with the channel is freed and new
commands are dispatch on the same channel, OS needs to wait until it
gets back the ownership. If not, either OS may end up overwriting the
platform response for the last command(which is fine as OS timed out
that command) or platform might overwrite the payload for the next
command with the response for the old.
The latter is problematic as platform may end up interpretting the
response as the payload. In order to avoid such race, let's wait until
the OS gets back the ownership before we prepare the shared memory with
the payload for the next command.
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In preparation to adding support for other two types of messages that
SCMI specification mentions, let's replace the term 'command' with the
correct term 'message'.
As per the specification the messages are of 3 types:
commands(synchronous or asynchronous), delayed responses and notifications.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
While adding new comments found couple of typos that are better fixed.
s/informfation/information/
s/statues/status/
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
scmi_xfer_get_init ensures both transmit and receive buffer lengths are
within the maximum limits. If receive buffer length is not supplied by
the caller, it's set to the maximum limit value. Receive buffer length
is never modified after that. So there's no need for the extra check
when receive transmit completion for a command essage.
Further, if the response header length is greater than the prescribed
receive buffer length, the response buffer is truncated to the latter.
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Looks like more code developed during the draft versions of the
specification slipped through and they don't match the final
released version. This seem to have happened only with sensor
protocol.
Renaming few command and function names here to match exactly with
the released version of SCMI specification for ease of maintenance.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fix to correct the SPDX License Identifier style in header file related
to firmware frivers for ARM SCMI message protocol.
For C header files Documentation/process/license-rules.rst mandates
C-like comments(opposed to C source files where C++ style should be
used).
While at it, change GPL-2.0 to GPL-2.0-only similar to the ones in
psci.h and scpi_protocol.h
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The reset-simple driver can be now used on DesignWare IPs by
default by selecting the following compatible strings:
- snps,dw-high-reset for active high resets inputs
- snps,dw-low-reset for active low resets inputs
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Luis Oliveira <luis.oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This adds documentation of device tree bindings for the
DesignWare IP reset controller.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Luis Oliveira <luis.oliveira@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Some of the mipi dsi resets were called
IMX8MQ_RESET_MIPI_DIS__
instead of
IMX8MQ_RESET_MIPI_DSI__
Since they're DSI related this looks like a typo. This fixes the
only in tree user as well to not break bisecting.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
property and related info to support i.MX8MM.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Flexible array members should be denoted using [] instead of [0], else
gcc will not warn when they are no longer at the end of the structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
QUICC Engine
- Add support for importing qe-snums through device tree
- Some cleanups and foot print optimzation
-----BEGIN PGP SIGNATURE-----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=zaF/
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.3 (take 2)
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
QUICC Engine
- Add support for importing qe-snums through device tree
- Some cleanups and foot print optimzation
* tag 'soc-fsl-next-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: fold qe_get_num_of_snums into qe_snums_init
soc: fsl: qe: support fsl,qe-snums property
dt-bindings: soc: fsl: qe: document new fsl,qe-snums binding
soc: fsl: qe: introduce qe_get_device_node helper
soc: fsl: qe: reduce static memory footprint by 1.7K
soc: fsl: qe: drop useless static qualifier
soc: fsl: fix spelling mistake "Firmaware" -> "Firmware"
Link: https://lore.kernel.org/r/20190605194511.12127-1-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix several warnings/errors in validation of binding schemas.
-----BEGIN PGP SIGNATURE-----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=IkH4
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
Pull vfs documentation typo fix from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix: it's d_make_root, not d_make_inode...
-----BEGIN PGP SIGNATURE-----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=rP0b
-----END PGP SIGNATURE-----
Merge tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
Roy Pledge