This enables the power button driver gets corresponding IRQ number by
using platform_get_irq().
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the charger driver gets corresponding IRQ number by using
platform_get_irq_byname() helper.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x bone based boards have the PMIC interrupt named NMI which is
connected to TPS65217 device. AM335x main interrupt controller provides it
and the number is 7.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support the power button driver and disable it by default.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS65217 MFD driver supports the IRQ domain to handle the charger input
interrupts and push button status event. The interrupt controller enables
corresponding IRQ handling in the charger[*] and power button driver[**].
[*] drivers/power/supply/tps65217_charger.c
[**] drivers/input/misc/tps65218-pwrbutton.c
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In drivers/mmc/core/host.c, there is a "max-frequency" property.
Behavior should not change, so use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In drivers/mmc/core/host.c, there is "max-frequency" property.
It should be same behavior. So use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the QSPI node and add the flash chip.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Use n25q00 for the compatible entry for the flash part and
tested on SoCKit
v2: Remove partition entries for the SoCKIT
Add a more specific board compatible entry for all of the SOCFPGA
Cyclone 5 based boards.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v3: Be a bit more specific with the c5 dk and sockit, use
"altr,socfpga-cyclone5-socdk" and "terasic,socfpga-cyclone5-sockit"
v2: remove extra space and add a comma between compatible entries
According to the latest best practices, unit-addresses should be
represented without any leading zeroes.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ("766a1fe78fc3 ARM: omap3: Add missing memory node") added
the memory node, but the patch didn't have the correct starting address.
This patch fixes the correct starting address.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sama5d2 has some static RAM that can be erased by the security module,
add its node
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that there is support for the sama5d4 slow clock controller, use its
driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The actual frequency was updated in commit ae142bd997 ("ARM: mvebu:
Fix the main PLL frequency on Armada 375, 38x and 39x SoCs") but the
comment was not updated. Update it now.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the GPU node for tegra124 nyan boards, which is required to
get graphics acceleration with nouveau on these devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the GMI controller found on Tegra30.
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the GMI controller found on Tegra20.
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently driver leaves sdmmc frequency at its default.
So lets set this to 50MHz.
This gives us performance boost in mmc transfers.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Exynos4 like other Cortex-A9 SoC's has a Snoop Control Unit(SCU)
and its SFR are used during SMP boot and S2R. Add SCU node to the device tree.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
These hardware blocks are SoC-specific, so their compatible strings
should be SoC-specific as well. This change has no impact on the
actual behavior since it is controlled by the generic "simple-mfd",
"syscon" compatible strings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I notice some mistakes in the SoC DTSI; wrong interrupts properties
of timer nodes, mismatch between the node name and the compatible
for sdctrl block. Given those problems fixed, the common parts
among SoCs are less than I had first expected. The more and more
property overrides are making the SoC DTSI unreadable.
Stretch out the SoC DTSI files and fix the following:
- Fix the 3rd cell of the interrupts property of the timer nodes
for Pro4, Pro5, PXs2
- Fix the node name mioctrl to sdctrl for Pro5, PXs2
- Fix the second region of l2 node for PXs2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
imx-weim should always set address-cells to 2,
and size_cells to 1.
On imx6, fsl,weim-cs-gpr will always be &gpr
Set these common parameters in the dtsi file,
rather than in a downstream dts.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit fa93fd4ecc ("regulator: core: Ensure we are at least in
bounds for our constraints") the imx53-qsb board populated with a Dialog
DA9053 PMIC fails to boot:
LDO3: Bringing 3300000uV into 1800000-1800000uV
The LDO3 voltage constraints passed in the device tree do not match
the valid range according to the datasheet, so fix this accordingly to
allow the board booting again.
While at it, fix the other voltage constraints as well.
Cc: <stable@vger.kernel.org> # 4.7.x
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The System Control node has 0x10000 byte of registers. The current
reg size must be expanded to use the cpufreq driver because the
registers controlling CPU frequency are located at offset 0x8000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds lsi / lse oscillators. These clocks can be use by
RTC clocks.
The clock drivers needs to disable the power domain write protection using
syscon / regmap to enable these clocks.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch aligns clocks names and node reference according to new
stm32-dwmac glue binding. It also renames Ethernet pinctrl phandle
(indeed there is no need to add 0 as Ethernet instance as there is only
one IP in SOC).
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
stm32f469-disco and stm32f429-eval boards use SDRAM start address remapping
(to @0) to boost performances. A DMA translation through "dma-ranges"
property was needed for other masters than the M4 CPU.
stm32f429-disco doesn't use remapping so doesn't need this DMA translation.
This patches moves this DMA translation definition from stm32f429 soc file
to board files.
Tested-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Up to now a working i2c bus depended on the bootloader to configure the
pinmuxing. Make it explicit.
As a side effect this change makes i2c work in barebox.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add device tree for the Oxford Seminconductor OX820 SoC and the
Cloud Engines PogoPlug v3 board.
Add the SoC and board compatible strings to oxnas bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
DU0 uses an externally provided clock, but the corresponding pin isn't
correctly muxed. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The system uses one address cell and one size cell, not two. Fix the DU
DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support in the dts for the HDMI input. Based on the Lager dts
patch from Ulrich Hecht.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[uli: removed "renesas," prefixes from pfc nodes]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT entries for vin0, vin0_pins, and adv7612.
Sets the 'default-input' property for ADV7612, enabling image and video
capture without the need to have userspace specifying routing.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
[uli: added interrupt, renamed endpoint, merged default-input]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,dvc/dvc@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,dvc/dvc@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,mix/mix@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,mix/mix@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@8 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@9 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 parts of the MSIOF0/1 device nodes.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the MSIOF0/1 clocks and their parent, MP clock in the R8A7792
device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7513 HDMI transmitters
connected to DU0/1. Add the necessary subnodes to interconnect DU with
HDMI transmitters/connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1,2}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
There are no boards in mainline using exynos4415.dtsi. These DTSIs
were not tested for long. I am also not aware of any popular out-of-tree
boards using this (except consumer devices released by Samsung but those
cannot use mainline).
Keeping Exynos4415 costs some useless effort so remove it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Therefore aligning the panel nodes name across all platforms.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Therefore aligning the panel nodes name across all platforms.
Also removing the bt_rfkill node since the mainline rfkill-gpio driver
doesn't support device trees.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Also aligning the panel nodes name across all platforms.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Also aligning the panel nodes name across all platforms.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SoM based on i.MX6 Quad with 1GB of DDR3.
https://boundarydevices.com/product/nit6x-som-v2/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add FEC support for Engicam i.CoreM6 dql modules.
Observed similar 'eth0: link is not ready' issue which was
discussed in [1] due rmii mode with external ref_clk, so added
clock node along with the properties mentioned by Shawn in [2]
FEC link log:
------------
$ ifconfig eth0 up
[ 27.905187] SMSC LAN8710/LAN8720 2188000.ethernet:00: attached PHY driver
[SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
[ 27.918982] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[1] https://patchwork.kernel.org/patch/3491061/
[2] https://patchwork.kernel.org/patch/3490511/
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 DualLite/Solo modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 Quad/Dual modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With commit 851ce93224 ("usb: chipidea: otg: don't wait vbus
drops below BSV when starts host"), the driver can support
enabling vbus output without software control, so this board
(control vbus output through ID pin) can support dual-role now.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: drop OF_DEV_AUXDATA() addition]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
i.MX31 Clock Control Module controller is found on AIPS2 bus, move it
there from SPBA bus to avoid a conflict of device IO space mismatch.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The type of AVIC interrupt controller found on i.MX31 is one-cell,
namely 31 for CCM DVFS and 53 for CCM, however for clock control
module its interrupts are specified as 3-cells, fix it.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The address of the mailbox node in the bcm283x.dtsi also has a typo.
So fix it accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Fixes: 05b682b7a3 ("ARM: bcm2835: dt: Add the mailbox to the device tree")
Signed-off-by: Eric Anholt <eric@anholt.net>
Add pins used by the LCD controller and a disabled LCDC node to be
reused in device trees including da850.dtsi.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[Bartosz:
- added the commit description
- changed the dt node name to a generic one
- added a da850-specific compatible string
- removed the tilcdc,panel node
- moved the pins definitions to da850.dtsi as suggested by
Sekhar Nori (was in: da850-lcdk.dts)]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: fix compatible property and remove interrupt-parent]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Addition of CPU dmips/capacity information to TC2 platform
2. Cleanup/fix unit address warnings and removal of skeleton.dtsi from
MPS2 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fUUJ
-----END PGP SIGNATURE-----
Merge tag 'vexpress-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
ARMv7 Vexpress DT fixes/updates for v4.10
1. Addition of CPU dmips/capacity information to TC2 platform
2. Cleanup/fix unit address warnings and removal of skeleton.dtsi from
MPS2 device tree
* tag 'vexpress-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: add TC2 cpu capacity-dmips-mhz information
ARM: dts: mps2: remove skeleton.dtsi include and fix unit address warnings
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYDhQ/AAoJEFBXWFqHsHzOjK8H/0BpUb5J1q+ULcJr5boRoErh
LIILJA3q0voOXjONRhOcUx8d3yVccR4AFDsMxP3fzfzDvHrNJcK0ldqMg2I/TvL9
0hUt/IDxSoQ4dCtuuMpWMATeAiUGzCebxKfg12stB+wXUALD7upBrLNP509/Vifw
O8xhPW5w5nWJ5g72QHpDQIqG0Le0Lf4lhuvPsS/hYOeL6mkGVfDTRMOduM3n3KLd
YSMj9NuG1IH9f4xKxGVcs/2ZPdNk+t0PfP/NuPIY3S0qtWwkJRQSPV314WEsxDff
pSCD/KhtkWf8VsHbOgiZUKXPQEsUuKLpqnjjkuF2Sm9KmYCgvaXfLfyX2eyyMN8=
=Xh9e
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a cognitive load to figure out which mmc device node corresponds
to the eMMC flash, uSD card and WiFI SDIO module on the Snow, Peach Pi
and Pit boards.
So it's better to have comments in the DTS to make this more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
[krzk: Squashed three patches into one]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- Add a Macnica sodia board
- Add support for the Arria10 System resource device
- Add support for the Arria10 LEDs
- Add QSPI to the socrates board
- Update L2 cache settings, enabling arm,shared-override
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yf+4
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.10_part_1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS update for v4.10, part 1
- Add a Macnica sodia board
- Add support for the Arria10 System resource device
- Add support for the Arria10 LEDs
- Add QSPI to the socrates board
- Update L2 cache settings, enabling arm,shared-override
* tag 'socfpga_dts_for_v4.10_part_1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: socrates: enable qspi
ARM: dts: socfpga: add qspi node
ARM: dts: socfpga: Add LED framework to A10-SR GPIO
ARM: dts: socfpga: Enable GPIO parent for Arria10 SR chip
ARM: dts: socfpga: Add Devkit A10-SR fields for Arria10
ARM: dts: socfpga: Add SPI Master1 for Arria10 SR chip
ARM: dts: socfpga: enable arm,shared-override in the pl310
ARM: dts: socfpga: Add Macnica sodia board
ARM: dts: socfpga: Add new MCVEVK manufacturer compat
Signed-off-by: Olof Johansson <olof@lixom.net>
The change setup the peripheral clock (PERIPH_CLK) as the default
parent clock for PWM1 & PWM2.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
When the patch is applied, the allwinner,driver and allwinner,pull
properties are removed.
Although they're described to be optional in the devicetree binding,
without them, the pinmux cannot be initialized, and the uart cannot
be used.
Add them back to fix the problem, and makes the bluetooth on iNet D978
Rev2 board work.
Fixes: 82eec38424 (ARM: dts: sun8i: add pinmux for UART1 at PG)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to support the Qualcomm MDM9615 SoC, add the SoC dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
liteBoard is a development board which uses liteSOM as its base.
Hardware specification:
* liteSOM (i.MX6UL, DRAM, eMMC)
* Ethernet PHY (id 0)
* USB host (usb_otg1)
* MicroSD slot (uSDHC1)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a SOM (System on Module), so it will be part of another boards.
Hence, this is a "dtsi" file that will be included from another device
tree files.
Hardware specification:
* Freescale i.MX6UL SoC
* up to 512 MB RAM
* eMMC on uSDHC2
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The global timer IRQ (PPI[0], PPI 11 in device tree terms) is a
rising edge interrupt. The ARM Cortex-A5 MPCore TRM in Chapter
10.1.2. Interrupt types and sources says:
"Interrupt is rising-edge sensitive."
The bits seem to be read-only, hence this missconfiguration had
no negative effect. However, with commit 992345a58e
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
warnings such as this get printed:
GIC: PPI11 is secure or misconfigured
With this change the new configuration matches the default
configuration and no warning is printed anymore.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initial device trees for UDOO Neo Basic, Extended and Full boards:
* Serial console is enabled, other serial ports are prepared.
* I2C based PMIC is enabled.
* Ethernet is enabled for Basic and Full.
* SDHC is enabled, with the SDIO_PWR GPIO modeled as a regulator.
* Both user LEDs are enabled, with the orange one reserved for the M4
and with the SD card as default trigger for the red LED.
The decision on a board compatible string is deferred to later.
Cc: Ettore Chimenti <ettore.chimenti@udoo.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LCDIF interrupt should be triggered by the rising edge of the
IRQ line because we only want the interrupt to trigger once per each
frame. It seems the LCDIF IRQ line cannot be explicitly de-asserted
by software, so the previous behavior before this patch, where the
interrupt was triggered by level-high status of the IRQ line, caused
the interrupt to fire again immediatelly after it was handled, which
caused the system to lock up due to the high rate of interrupts.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C3 bus was only brought out in revision A1 of the board and revision
B1 only brings out 3 I2C busses (I2C0, I2C1 and I2C2).
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixed no space before tabs warnings in respetcive imx6qdl dtsi files.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Calibrate the USB PHY TX settings to pass the eye diagram signal
integrity test. The settings are taken from the i.MX6 reference
manual's recommended configuration for USB certification (66.2.6).
Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove use of pwm-leds and use the standard /sys/class/pwm
interface from PWM subsystem.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use definition in rockchip pinctrl header to describe
gpios, this will make it more clear.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MK808 is a tv stick which has rockchip rk3066 CPU inside, two usb ports
- host and otg, micro sd card slot and onboard wifi RK901.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Initialize PLL, cpu bus and peripherial bus rate while kernel init.
No other module does than.
This gives us performance boost observable for example in mmc transfers.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Remove pullup on dbgu DTXD signal, it is a push-pull output thus the
pullup is pointless.
Add pullup on dbgu DRXD signal, it prevents the DRXD signal to be left
floating and so consuming a useless extra amount of power in crowbarred
state if nothing is externally connected to dbgu.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch enables the RX and TX FIFOs (16 data each) of the two
high-speed i2c controllers (i2c0 and i2c1).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Once the ST frontend demux HW IP has been enabled, the clock can't
be disabled otherwise the system will hang and the board will
be unserviceable.
To allow balanced clock enable/disable calls in the driver we use
the critical clock infrastructure to take an extra reference on the
clock so the clock will never actually be disabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
sti-hdmi is already enabled in stih410.dtsi.
So no need to declare it here.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add new dai link in sound card to support HDMI output
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Cleaning of some uni-players and uni-reader fields.
Associated configurations are now handled in driver based
on compatible string.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.
[1] https://patchwork.kernel.org/patch/9157571/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove 0x from pinctrl node to match device tree naming convention.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
ILP clock (sometimes called a "slow clock") is a part of PMU (Power
Management Unit). There has been recently added a driver for it, so add
a proper entry in the DT as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Luxul XWR-3100 is a wireless router based on BCM47094 SoC with two
4366c0 FullMAC PCIe cards on the PCB. It uses NAND with BCH-4 ECC
algorithm.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Luxul XAP-1510 is an AP device based on BCM4708 SoC with 2 x BCM4360
chipsets on PCB connected using PCIe.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Driver for Northstar USB 3.0 PHY has been recently added under the name
phy-bcm-ns-usb3. Add binding for it into the DT files.
The only slightly tricky part is BCM47094 which uses different PHY
version and requires different compatible value.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It was tested by LEDE users, all we need is to adjust clock frequency.
While we're at it create a separated DTS include file to share code with
other BCM4709 devices easier.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Use it to store BCM47094 specific properties/values and avoid repeating
them in device DTS files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding QSPI Device Tree node compatible with the new spi-bcm-qspi driver for
the Broadcom Northstar Plus SoC DTSI and bcm958625k reference board.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM53573 seems to be low priced alternative for Northstar chipsts. It
uses single core Cortex-A7 and doesn't have SDU or local (TWD) timer. It
was also stripped out of independent SPI controller and 2 GMACs.
DTS for Tenda AC9 isn't completed yet. It misses e.g. switch entry (we
still need some b53 fixes) and probably some clocks. It adds support for
basic features however and can be improved later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Netgear R8500 is another BCM47094 device, it just has three BCM4366
wireless chipsets. It's a very standard DT with mostly GPIO devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable the qspi controller on the socrates and add the flash chip.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the LED framework to the Arria10 System Resource chip GPIO hooks.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the Altera Arria10 System Resource node. This is a Multi-Function
device with GPIO expander support.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the Altera Arria10 SPI Master Node in preparation for
the A10SR MFD node.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Enable the bit(22) shared-override bit for the SoCFPGA family. While at it,
enable the prefetch-data and prefetch-instr settings for the Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add support for board based on the Altera Cyclone V SoC.
This board has the following functions:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 SD card slot
- 1 USB gadget port
- QSPI NOR Flash
- I2C EEPROMs and I2C RTC
- DVI output
- Audio port
This commit supports without QSPI, DVI and Audio.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The TOPEET itop Exynos4412 has three versions of base boards. The
Elite version is the cheap one without too much peripheral devices
on it.
Currently supported are serial console, wired networking (USB), USB OTG
in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC
and LEDs. The WM8960 analog audio codec is also enabled.
The FIMC is not used for camera currently, I enabled it just for a
colorspace converter.
Signed-off-by: Randy Li <ayaka@soulik.info>
Acked-by: Rob Herring <robh@kernel.org>
[krzk: fixup pin function macro, adjust commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The TOPEET itop is a Samsung Exynos4412 core board, which has
two package versions. This patch adds the support for SCP version.
Currently supported are USB3503A HSIC, USB OTG, eMMC, RTC and
PMIC. The future features are in the based board. Also MFC and
watchdog have been enabled.
Signed-off-by: Randy Li <ayaka@soulik.info>
[krzk: fixup pin function macro, adjust commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The current delay settings of the phy are not the optimal value,
fix it with correct values.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default impedance settings of the phy is not the optimal
value, due to this the second ethernet is not working. Fix it
with correct values which makes the second ethernet port to work.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a very annoying regression on the Snowball SD card
that has been around for a while. It turns out that the device
tree does not configure the direction pins properly, nor sets
up the pins for the voltage converter properly at boot. Unless
all things are correctly set up, the feedback clock will not
work, and makes the driver spew messages in the console (but
it works, very slowly):
root@Ux500:/ mount /dev/mmcblk0p2 /mnt/
[ 9.953460] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
[ 9.960296] mmcblk0: error -110 sending status command, retrying
[ 9.966461] mmcblk0: error -110 sending status command, retrying
[ 9.972534] mmcblk0: error -110 sending status command, aborting
Fix this by rectifying the device tree to correspond to that of
the Ux500 HREF boards plus the DAT31DIR setting that is unique for
the Snowball, and things start working smoothly. Add in the SDR12
and SDR25 modes which this host can do without any problems.
I don't know if this has ever been correct, sadly. It works after
this patch.
Cc: stable@vger.kernel.org
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
As the alt3 group has no pins left drop it from &gpio.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
The BCM2835-ARM-Peripherals.pdf documentation specifies what the
function selects do for the pins, and there are a bunch of obvious
groupings to be made. With these created, we'll be able to replace
bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
references to specific groups we want enabled.
Also add pinctrl groups for emmc and sdhost.
Based on patches by Eric Anholt, with fixups by Gerd Hoffmann.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
This patch adds device nodes for the AUDSS clock controller,
peripheral DMA 0/1 controllers and the Audio Subsystem I2S controller.
These entries are required for sound support on Odroid-XU board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "simple-bus" compatible was originally added for fimc-is only
to ensure the child devices instantiation. The child devices are
now being created by the parent device driver so remove the
"simple-bus" compatible.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to now working ethernet depended on the bootloader to configure the
pinmuxing. Make it explicit.
As a side effect this change makes ethernet work in barebox.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The compatible is supposed to be "marvell,mv78230-i2c", "marvell,mv64xxx-i2c",
as provided by armada-xp.dtsi.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Up to now a working i2c bus depended on the bootloader to configure the
pinmuxing. Make it explicit.
As a side effect this change makes i2c work in barebox.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Enable these two modes to speed up the booting and improve
the performance.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PopMetal-RK3288 board could enable SD3.0 card but need vccio_sd
to support the voltage range from 1V8 to 3V3 and we also need to
add more UHS mode here.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Please don't add these for vcc_sd, and mmc-core/driver will control
it. Otherwise, it will waste energy even without sdmmc in slot.
Moreover, it will causes a bug:
If we insert/remove sd card, we could see
[9.337271] mmc0: new ultra high speed SDR25 SDHC card at address 0007
[9.345144] mmcblk0: mmc0:0007 SD32G 29.3 GiB
This is okay for normal sd insert/remove test, but when I debug some
issues for sdmmc, I did unbind/bind test. And there is a interesting
phenomenon when we bind the driver again:
[58.314069] mmc0: new high speed SDHC card at address 0007
[58.320282] mmcblk0: mmc0:0007 SD32G 29.3 GiB
So the sd card could just support high speed without power cycle
since the vcc_sd is always on, which makes the sd card fail to
reinit its internal ocr mask.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX3 EVB is designed by Rockchip for automotive field,
with integrated CVBS (TP2825) / MIPI DSI / LVDS / HDMI
video input/output interface, WIFI/BT/GPS (on a module
named S500 which based on MT6620), Gsensor BMA250E and
light&proximity sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same, besides empty chosen nodes
being removed. So the change should not have a functional impact.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same, besides empty chosen nodes
being removed. So the change should not have a functional impact.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same, besides empty chosen nodes
being removed. So the change should not have a functional impact.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same, besides empty chosen nodes
being removed. So the change should not have a functional impact.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
Pull drm updates from Dave Airlie:
"Core:
- Fence destaging work
- DRIVER_LEGACY to split off legacy drm drivers
- drm_mm refactoring
- Splitting drm_crtc.c into chunks and documenting better
- Display info fixes
- rbtree support for prime buffer lookup
- Simple VGA DAC driver
Panel:
- Add Nexus 7 panel
- More simple panels
i915:
- Refactoring GEM naming
- Refactored vma/active tracking
- Lockless request lookups
- Better stolen memory support
- FBC fixes
- SKL watermark fixes
- VGPU improvements
- dma-buf fencing support
- Better DP dongle support
amdgpu:
- Powerplay for Iceland asics
- Improved GPU reset support
- UVD/VEC powergating support for CZ/ST
- Preinitialised VRAM buffer support
- Virtual display support
- Initial SI support
- GTT rework
- PCI shutdown callback support
- HPD IRQ storm fixes
amdkfd:
- bugfixes
tilcdc:
- Atomic modesetting support
mediatek:
- AAL + GAMMA engine support
- Hook up gamma LUT
- Temporal dithering support
imx:
- Pixel clock from devicetree
- drm bridge support for LVDS bridges
- active plane reconfiguration
- VDIC deinterlacer support
- Frame synchronisation unit support
- Color space conversion support
analogix:
- PSR support
- Better panel on/off support
rockchip:
- rk3399 vop/crtc support
- PSR support
vc4:
- Interlaced vblank timing
- 3D rendering CPU overhead reduction
- HDMI output fixes
tda998x:
- HDMI audio ASoC support
sunxi:
- Allwinner A33 support
- better TCON support
msm:
- DT binding cleanups
- Explicit fence-fd support
sti:
- remove sti415/416 support
etnaviv:
- MMUv2 refactoring
- GC3000 support
exynos:
- Refactoring HDMI DCC/PHY
- G2D pm regression fix
- Page fault issues with wait for vblank
There is no nouveau work in this tree, as Ben didn't get a pull
request in, and he was fighting moving to atomic and adding mst
support, so maybe best it waits for a cycle"
* tag 'drm-for-v4.9' of git://people.freedesktop.org/~airlied/linux: (1412 commits)
drm/crtc: constify drm_crtc_index parameter
drm/i915: Fix conflict resolution from backmerge of v4.8-rc8 to drm-next
drm/i915/guc: Unwind GuC workqueue reservation if request construction fails
drm/i915: Reset the breadcrumbs IRQ more carefully
drm/i915: Force relocations via cpu if we run out of idle aperture
drm/i915: Distinguish last emitted request from last submitted request
drm/i915: Allow DP to work w/o EDID
drm/i915: Move long hpd handling into the hotplug work
drm/i915/execlists: Reinitialise context image after GPU hang
drm/i915: Use correct index for backtracking HUNG semaphores
drm/i915: Unalias obj->phys_handle and obj->userptr
drm/i915: Just clear the mmiodebug before a register access
drm/i915/gen9: only add the planes actually affected by ddb changes
drm/i915: Allow PCH DPLL sharing regardless of DPLL_SDVO_HIGH_SPEED
drm/i915/bxt: Fix HDMI DPLL configuration
drm/i915/gen9: fix the watermark res_blocks value
drm/i915/gen9: fix plane_blocks_per_line on watermarks calculations
drm/i915/gen9: minimum scanlines for Y tile is not always 4
drm/i915/gen9: fix the WaWmMemoryReadLatency implementation
drm/i915/kbl: KBL also needs to run the SAGV code
...
-----BEGIN PGP SIGNATURE-----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=JqCR
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably,
an ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets;
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E,
Orange Pi Lite, Olimex A33-Olinuxino, and Nano Pi Neo
single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform;
Raspberry Pi Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file);
Armada 395 SoC platform and GP board
Armada 390 DB development board
- NXP i.MX: imx7s Warp7 reference board;
Gateworks Ventana GW553x single-board computer,
Technologic Systems TS-4900 and
Engicam IMX6UL GEA M6UL computer-on-module,
Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board;
Firefly RK3288 Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer
Conflicts: vendor-prefixes.txt has conflicting additions, keep all of
them in alphabetical order.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/gg/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Pull ARM updates from Russell King:
- Correct ARMs dma-mapping to use the correct printk format strings.
- Avoid defining OBJCOPYFLAGS globally which upsets lkdtm rodata
testing.
- Cleanups to ARMs asm/memory.h include.
- L2 cache cleanups.
- Allow flat nommu binaries to be executed on ARM MMU systems.
- Kernel hardening - add more read-only after init annotations,
including making some kernel vdso variables const.
- Ensure AMBA primecell clocks are appropriately defaulted.
- ARM breakpoint cleanup.
- Various StrongARM 11x0 and companion chip (SA1111) updates to bring
this legacy platform to use more modern APIs for (eg) GPIOs and
interrupts, which will allow us in the future to reduce some of the
board-level driver clutter and elimate function callbacks into board
code via platform data. There still appears to be interest in these
platforms!
- Remove the now redundant secure_flush_area() API.
- Module PLT relocation optimisations. Ard says: This series of 4
patches optimizes the ARM PLT generation code that is invoked at
module load time, to get rid of the O(n^2) algorithm that results in
pathological load times of 10 seconds or more for large modules on
certain STB platforms.
- ARMv7M cache maintanence support.
- L2 cache PMU support
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (35 commits)
ARM: sa1111: provide to_sa1111_device() macro
ARM: sa1111: add sa1111_get_irq()
ARM: sa1111: clean up duplication in IRQ chip implementation
ARM: sa1111: implement a gpio_chip for SA1111 GPIOs
ARM: sa1111: move irq cleanup to separate function
ARM: sa1111: use devm_clk_get()
ARM: sa1111: use devm_kzalloc()
ARM: sa1111: ensure we only touch RAB bus type devices when removing
ARM: 8611/1: l2x0: add PMU support
ARM: 8610/1: V7M: Add dsb before jumping in handler mode
ARM: 8609/1: V7M: Add support for the Cortex-M7 processor
ARM: 8608/1: V7M: Indirect proc_info construction for V7M CPUs
ARM: 8607/1: V7M: Wire up caches for V7M processors with cache support.
ARM: 8606/1: V7M: introduce cache operations
ARM: 8605/1: V7M: fix notrace variant of save_and_disable_irqs
ARM: 8604/1: V7M: Add support for reading the CTR with read_cpuid_cachetype()
ARM: 8603/1: V7M: Add addresses for mem-mapped V7M cache operations
ARM: 8602/1: factor out CSSELR/CCSIDR operations that use cp15 directly
ARM: kernel: avoid brute force search on PLT generation
ARM: kernel: sort relocation sections before allocating PLTs
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into patchwork
Linux 4.8
* tag 'v4.8': (1761 commits)
Linux 4.8
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
MAINTAINERS: Switch to kernel.org email address for Javi Merino
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
x86/init: Fix cr4_init_shadow() on CR4-less machines
MIPS: Fix detection of unsupported highmem with cache aliases
MIPS: Malta: Fix IOCU disable switch read for MIPS64
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
...
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=b0/p
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
MMC core:
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
* tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc: (68 commits)
mmc: dw_mmc: remove the deprecated "supports-highspeed" property
mmc: dw_mmc: minor cleanup for dw_mci_adjust_fifoth
mmc: dw_mmc: use macro to define ring buffer size
mmc: dw_mmc: fix misleading error print if failing to do DMA transfer
mmc: dw_mmc: avoid race condition of cpu and IDMAC
mmc: dw_mmc: split out preparation of desc for IDMAC32 and IDMAC64
mmc: core: don't try to switch block size for dual rate mode
mmc: sdhci-of-arasan: Set controller to test mode when no CD bit
dt: sdhci-of-arasan: Add device tree option xlnx, fails-without-test-cd
mmc: tmio: add eMMC support
mmc: rtsx_usb: use new macro for R1 without CRC
mmc: rtsx_pci: use new macro for R1 without CRC
mmc: add define for R1 response without CRC
mmc: card: do away with indirection pointer
mmc: sdhci-acpi: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci-pci: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci: Support cap_cmd_during_tfr requests
mmc: mmc_test: Add tests for sending commands during transfer
mmc: core: Add support for sending commands during data transfer
mmc: sdhci-brcmstb: Fix incorrect capability
...
buffers (Thor Thayer)
* Split the memory controller part out of mpc85xx and share it with a
* new Freescale ARM Layerscape driver (York Sun)
* amd64_edac fixes (Yazen Ghannam)
* Misc cleanups, refactoring and fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pcI8
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A lot of movement in the EDAC tree this time around, coarse summary
below:
- Altera Arria10 enablement of NAND, DMA, USB, QSPI and SD-MMC FIFO
buffers (Thor Thayer)
- split the memory controller part out of mpc85xx and share it with a
new Freescale ARM Layerscape driver (York Sun)
- amd64_edac fixes (Yazen Ghannam)
- misc cleanups, refactoring and fixes all over the place"
* tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (37 commits)
EDAC, altera: Add IRQ Flags to disable IRQ while handling
EDAC, altera: Correct EDAC IRQ error message
EDAC, amd64: Autoload module using x86_cpu_id
EDAC, sb_edac: Remove NULL pointer check on array pci_tad
EDAC: Remove NO_IRQ from powerpc-only drivers
EDAC, fsl_ddr: Fix error return code in fsl_mc_err_probe()
EDAC, fsl_ddr: Add entry to MAINTAINERS
EDAC: Move Doug Thompson to CREDITS
EDAC, I3000: Orphan driver
EDAC, fsl_ddr: Replace simple_strtoul() with kstrtoul()
EDAC, layerscape: Add Layerscape EDAC support
EDAC, fsl_ddr: Fix IRQ dispose warning when module is removed
EDAC, fsl_ddr: Add support for little endian
EDAC, fsl_ddr: Add missing DDR DRAM types
EDAC, fsl_ddr: Rename macros and names
EDAC, fsl-ddr: Separate FSL DDR driver from MPC85xx
EDAC, mpc85xx: Replace printk() with pr_* format
EDAC, mpc85xx: Drop setting/clearing RFXE bit in HID1
EDAC, altera: Rename MC trigger to common name
EDAC, altera: Rename device trigger to common name
...
Pull irq updates from Thomas Gleixner:
"The irq departement proudly presents:
- A rework of the core infrastructure to optimally spread interrupt
for multiqueue devices. The first version was a bit naive and
failed to take thread siblings and other details into account.
Developed in cooperation with Christoph and Keith.
- Proper delegation of softirqs to ksoftirqd, so if ksoftirqd is
active then no further softirq processsing on interrupt return
happens. Otherwise we try to delegate and still run another batch
of network packets in the irq return path, which then tries to
delegate to ksoftirqd .....
- A proper machine parseable sysfs based alternative for
/proc/interrupts.
- ACPI support for the GICV3-ITS and ARM interrupt remapping
- Two new irq chips from the ARM SoC zoo: STM32-EXTI and MVEBU-PIC
- A new irq chip for the JCore (SuperH)
- The usual pile of small fixlets in core and irqchip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
softirq: Let ksoftirqd do its job
genirq: Make function __irq_do_set_handler() static
ARM/dts: Add EXTI controller node to stm32f429
ARM/STM32: Select external interrupts controller
drivers/irqchip: Add STM32 external interrupts support
Documentation/dt-bindings: Document STM32 EXTI controller bindings
irqchip/mips-gic: Use for_each_set_bit to iterate over local IRQs
pci/msi: Retrieve affinity for a vector
genirq/affinity: Remove old irq spread infrastructure
genirq/msi: Switch to new irq spreading infrastructure
genirq/affinity: Provide smarter irq spreading infrastructure
genirq/msi: Add cpumask allocation to alloc_msi_entry
genirq: Expose interrupt information through sysfs
irqchip/gicv3-its: Use MADT ITS subtable to do PCI/MSI domain initialization
irqchip/gicv3-its: Factor out PCI-MSI part that might be reused for ACPI
irqchip/gicv3-its: Probe ITS in the ACPI way
irqchip/gicv3-its: Refactor ITS DT init code to prepare for ACPI
irqchip/gicv3-its: Cleanup for ITS domain initialization
PCI/MSI: Setup MSI domain on a per-device basis using IORT ACPI table
ACPI: Add new IORT functions to support MSI domain handling
...
The change adds a new device node with description of generic SRAM
on-chip memory found on NXP LPC32xx SoC series and connected to AHB
matrix slave port 3.
Note that NXP LPC3220 SoC has 128KiB of SRAM memory, the other
LPC3230, LPC3240 and LPC3250 SoCs all have 256KiB SRAM space,
in the shared DTSI file this change specifies 128KiB SRAM size.
Also it's worth to mention that the SRAM area contains of 64KiB banks,
2 banks on LPC3220 and 4 banks on the other SoCs from the series, and
all SRAM banks but the first one have independent power controls,
the description of this feature will be added with the introduction of
power domains for the SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"Three relatively small fixes for ARM:
- Roger noticed that dma_max_pfn() was calculating the upper limit
wrongly, by adding the PFN offset of memory twice.
- A fix from Robin to correct parsing of MPIDR values when the
address size is larger than one BE32 unit.
- A fix from Srinivas to ensure that we do not rely on the boot
loader (or previous Linux kernel) setting the translation table
base register a certain way in the decompressor, which can lead to
crashes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
ARM: 8617/1: dma: fix dma_max_pfn()
ARM: 8616/1: dt: Respect property size when parsing CPUs
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894 ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2.
[1] http://www.spinics.net/lists/arm-kernel/msg528080.html
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2cd.
[1] http://www.spinics.net/lists/arm-kernel/msg528080.html
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2q.
[1] http://www.spinics.net/lists/arm-kernel/msg528080.html
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
After commit f29a72c24a ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
After commit f29a72c24a ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX6H4uAAoJEHm+PkMAQRiG5sMH/3yzrMiUCSokdS+cvY+jgKAG
JS58JmRvBPz2mRaU3MRPBGRDeCz/Nc9LggL2ZcgM+E1ZYirlYyQfIED3lkqk5R07
kIN1wmb+kQhXyU4IY3fEX7joqyKC6zOy4DUChPkBQU0/0+VUmdVmcJvsuPlnMZtf
g95m0BdYTui+eDezASRqOEp3Lb5ONL4c3ao4yBP0LHF033ctj3VJQiyi5uERPZJ0
5e6Mo7Wxn78t9WqJLQAiEH46kTwT2plNlxf3XXqTenfIdbWhqE873HPGeSMa3VQV
VywXTpCpSPQsA8BYg66qIbebdKOhs9MOviHVfqDtwQlvwhjlBDya0gNHfI5fSy4=
=Y/L5
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rc8' into drm-next
Linux 4.8-rc8
There was a lot of fallout in the imx/amdgpu/i915 drivers, so backmerge
it now to avoid troubles.
* tag 'v4.8-rc8': (1442 commits)
Linux 4.8-rc8
fault_in_multipages_readable() throws set-but-unused error
mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing
radix tree: fix sibling entry handling in radix_tree_descend()
radix tree test suite: Test radix_tree_replace_slot() for multiorder entries
fix memory leaks in tracing_buffers_splice_read()
tracing: Move mutex to protect against resetting of seq data
MIPS: Fix delay slot emulation count in debugfs
MIPS: SMP: Fix possibility of deadlock when bringing CPUs online
mm: delete unnecessary and unsafe init_tlb_ubc()
huge tmpfs: fix Committed_AS leak
shmem: fix tmpfs to handle the huge= option properly
blk-mq: skip unmapped queues in blk_mq_alloc_request_hctx
MIPS: Fix pre-r6 emulation FPU initialisation
arm64: kgdb: handle read-only text / modules
arm64: Call numa_store_cpu_info() earlier.
locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text
nvme-rdma: only clear queue flags after successful connect
i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended
perf/core: Limit matching exclusive events to one PMU
...
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones for all Tegra124 platform, these trips can trigger
shut down or reset.
Tegra124 Jetson TK1 was already set "critical" trips before, so it
can overwrite the general values.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the tilcdc quirks:
- Fix typo with recent beagleboard-x15 changes for mmc2_pins_default
- Add am335x blue-and-red-wiring quirk as specified in the binding in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt. Also
fix up the whitespace formatting for am335x-evmsk.
- Fix for recent igepv5 power button for GPIO_ACTIVE_LOW. Also fix
up the whitespace formatting for the button
-----BEGIN PGP SIGNATURE-----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=14Zw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/dt-pt3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "few minor fixes for omap dts files for v4.9 merge window"
Few fixes for omap dts files for v4.9 merge window. Let's also add
the tilcdc quirks:
- Fix typo with recent beagleboard-x15 changes for mmc2_pins_default
- Add am335x blue-and-red-wiring quirk as specified in the binding in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt. Also
fix up the whitespace formatting for am335x-evmsk.
- Fix for recent igepv5 power button for GPIO_ACTIVE_LOW. Also fix
up the whitespace formatting for the button
* tag 'omap-for-v4.9/dt-pt3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am57xx-beagle-x15-common: Fix wrong pinctrl selection for mmc2
Here is a bunch of late changes for the 4.9 merge window, mostly:
- Added a bunch of touchscreens nodes to tablets
- Added support for the AXP806 PMIC found in the A80 boards
- Enabled a few pinmux options for the H3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YfLG
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/late
Pull "Allwinner DT changes for 4.9, late edition" from Maxime Ripard:
Here is a bunch of late changes for the 4.9 merge window, mostly:
- Added a bunch of touchscreens nodes to tablets
- Added support for the AXP806 PMIC found in the A80 boards
- Enabled a few pinmux options for the H3
* tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
Add a dt node describing the mma7660 accelerometer on the
polaroid-mid2407pxe03 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART1 is connected to the bluetooth part of RTL8723BS WiFi/BT combo card
on iNet D978 Rev2 board.
Enable the UART1 to make it possible to use the modified hciattach by
Realtek to drive the BT part of RTL8723BS.
On the board no r_uart pins are found now (the onboard RX/TX pins are
wired to PF2/PF4, which is muxed with mmc0), so also disabled it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UART1 at PG (PG6, PG7, PG8, PG9) is, in the Allwinner's reference
tablet design of A23/33, used to connect to UART Bluetooth cards.
Add the pinmux for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These peripherals can only be muxed to these pins, so they are
associated in the DTSI instead of the board files. This makes it very
easy to enable them using overlays or u-boot commands:
=> fdt set /soc/i2c@01c2ac00 status okay
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are the only possible pins for these peripherals according to the
datasheet.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These H3 boards all expose UART1-3 on their expansion header. Since
other functions can be muxed to these pins, they are explicitly
disabled. To enable them, one could use DT overlays or U-boot commands:
=> fdt set /soc/serial@01c28c00 status okay
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This was done to make UART1-3 on H3 consistent, and less complicated to
enable UART1-3 on the breakout header on the several H3 board (notably
Orange Pi's). This patch adds a bit of complexity for the existing Banana
Pi, which already had the RTS/CTS associated on UART1.
The RTS/CTS for UART2-3 could be defined in the same way, but since
there is no actual use case for them at the moment, they are left out.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are the pinmux definitions for UART2-3 on H3. These UARTs can only
be muxed to these pins, so _a and @0 do not really make sense. I have
left out RTS/CTS, since these are rarely used. These can easily be
enabled using an additional pinmux set.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
EHCI1 provides an HSIC interface. This interface is exposed on the
board through two pins among the GPIO header.
With the PHY now powered up and responding, enabling the interface when
nothing is connected results in a lot of error messages:
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 3 using ehci-platform
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 4 using ehci-platform
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high-speed USB device number 5 using ehci-platform
usb 2-1: device not accepting address 5, error -71
usb usb2-port1: unable to enumerate USB device
Disable it by default, but leave the entries in the board DTS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809's SW (switch) regulator is unused on the A80 Optimus.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h tablet has a gsl3675 touchscreen, add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Add a node enabling the gsl3670 touchscreen controller found on
sun8i-a23-polaroid-mid2809pxe04 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Add a node enabling the gsl1680 touchscreen controller found on
sun8i-a23-polaroid-mid2407pxe03 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The inet86dz tablet has a gsl1680 touchscreen,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gt90h tablet has a gsl3675 touchscreen, add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
And here's another nitpick ;-)
Cc: Agustí Fontquerni i Gorchs <afontquerni@iseebcn.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Pau Pajuel <ppajuel@gmail.com>
Fixes: b118c6a6ff ("ARM: dts: Add power button support for igepv5")
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
It should be GPIO_ACTIVE_LOW instead of GPIO_ACTIVE_HIGH as
pointed out by Pau Pajuel <ppajuel@gmail.com>.
Cc: Agustí Fontquerni i Gorchs <afontquerni@iseebcn.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Pau Pajuel <ppajuel@gmail.com>
Fixes: b118c6a6ff ("ARM: dts: Add power button support for igepv5")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add blue-and-red-wiring -property to lcdc node. The am335x-evmsk has
blue and red wires crossed to get 24-bit RGB (and 16-bit BGR)
support. After this patch am335x-evmsk supports BGR565, RGB888, and
XRGB8888 color formats. See details in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Whitespace cleanup of lcdc related nodes. Do all indentation and
alignment with tabs instead of spaces.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add blue-and-red-wiring -property to lcdc node. The am335x-evm has
blue and red wires crossed to get 24-bit RGB (and 16-bit BGR)
support. After this patch am335x-evm supports BGR565, RGB888, and
XRGB8888 color formats. See details in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NN8A
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Topic branch for Samsung DeviceTree cleanup for 4.9" from Krzysztof Kozłowski:
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
* tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
ARM: dts: exynos: Fix mismatched values of SD drive strengh configuration on exynos4415
ARM: dts: exynos: Fix mismatched value for SD4 pull up/down configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos542x/exynos5800
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5410
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5260
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5250
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4415
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4x12
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos3250
ARM: dts: exynos: Use common macros for pinctrl configuration
pinctrl: dt-bindings: samsung: Update documentation with new macros
pinctrl: dt-bindings: samsung: Add header with values used for configuration
1. Enable HDMI on Arndale Octa board.
2. Update list of clocks for FIMC-IS block on Exynos4x12.
3. Remove skeleton.dtsi thus fixing DT compiler warning:
"Node /memory has a reg or ranges property, but no unit name"
This is a tree-wide effort by various people. Javier Martinez Canillas did
it for Exynos and S5PV210.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJX3r7xAAoJEME3ZuaGi4PXBhAQAINQXD3iOkN8bLI6t29uZYgz
JMaOw+uIowZnOsREj/MnqN3b2GbuTl4ubPshKoPmZZPJSW5z+ekE1pBq4rsd5seh
M4FNUZShyhpu8UeMXbn1xzXXBc1/iOYVRSbfwUnlfHeZ0yMdPd6/GliR6ecvq2Mo
vMbdQsqrLNWZEXbSzifOtDKBAuCM8Nedz90arKn1BieYP3cRSs14PQ+l31m6U7n8
6JQ5/1C8Gd23xFArzETLmWHJqBIDry8LrtswmYJ4tbZEvP+zoFEpNTvQxpNWgIW5
NOMnr/IPGajY4n+UACoX6QMTOV98GWwequb4RFVc02nQkyIlfK7jStPQ8O6uYJcL
IGNStOIrJhhrh4vejwlL6VA8xzSXligfDVpNUWWxrELBIMU1LqNTY1gMMjljn1i8
/RHip+5RBnpKc0JIebRLFeSQ7lE3WhxMTiGCdf01taXOpzYpw0tgcGQMqb1052ol
Fse2uICYBV9GJC5dAzSMSLOGERaZBvqyA5uD7WeGq8yeHnM5ORzXmHhVNc3ohpYv
Vjnww1LHBzwFFbQyelygp9CpHi/5YALgkhe+Eh3v11qrrKrJUus0Sb14eNb1aKDz
qo3+G+b9l/o6Aq2Zs4iIhjOPhnk1q5TTIIdzBffgDf6WShd7/VtZnB0xVTlzG/f9
7dGXx1DKq4bJEREdW8xs
=gG35
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DeviceTree update for v4.9, second round" from Krzysztof Kozłowski:
1. Enable HDMI on Arndale Octa board.
2. Update list of clocks for FIMC-IS block on Exynos4x12.
3. Remove skeleton.dtsi thus fixing DT compiler warning:
"Node /memory has a reg or ranges property, but no unit name"
This is a tree-wide effort by various people. Javier Martinez Canillas did
it for Exynos and S5PV210.
* tag 'samsung-dt-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5p: Add missing unit name to memory nodes for S5PV210 boards
ARM: dts: s5p: Remove skeleton.dtsi inclusion for S5PV210
ARM: dts: exynos: Add missing unit name to memory nodes in Exynos5 DTS
ARM: dts: exynos: Add missing unit name to memory nodes in Exynos4 DTS
ARM: dts: exynos: Add missing unit name to memory nodes in Exynos3 DTS
ARM: dts: exynos: Remove skeleton.dtsi usage for Exynos5
ARM: dts: exynos: Remove skeleton.dtsi usage for Exynos4
ARM: dts: exynos: Remove skeleton.dtsi usage for Exynos3
ARM: dts: exynos: Add missing memory node for Exynos5440 boards
ARM: dts: exynos: Add all required FIMC-IS clocks to exynos4x12
ARM: dts: exynos: Enable HDMI for Arndale Octa board
is mostly usability and non-critical fixes except for the addition of
beagleboard-x15 rev B1 support:
- Fix omap4 pandaboard SDIO WLAN latencies in idle mode by enabling wakeirq
- Usability fixes for WLAN, USB, LEDs and power button on omap5 boards
- Remove am57xx beagleboard-x15 pinmux configuration as the processor requires
that it's done in IO isolation in bootloader except for MMC and DCAN
- Add support for beagleboard-x15 rev B1 by moving most of the
configuration to am57xx-beagle-x15-common.dtsi
- Enable support for more than 2GB of memory for omap5 with LPAE with
#address-cells
- Fix omap3-gta04 backlight PWM frequency until the PWM driver
- Revert am335x dts changes related to cpufreq as the driver changes
still have not merged and the dts changes broke cpufreq
-----BEGIN PGP SIGNATURE-----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=HYYB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "omap dts updates for v4.9 merge window, part 2" from Tony Lindgren:
Part two of device tree changes for omaps for v4.9 merge window. This
is mostly usability and non-critical fixes except for the addition of
beagleboard-x15 rev B1 support:
- Fix omap4 pandaboard SDIO WLAN latencies in idle mode by enabling wakeirq
- Usability fixes for WLAN, USB, LEDs and power button on omap5 boards
- Remove am57xx beagleboard-x15 pinmux configuration as the processor requires
that it's done in IO isolation in bootloader except for MMC and DCAN
- Add support for beagleboard-x15 rev B1 by moving most of the
configuration to am57xx-beagle-x15-common.dtsi
- Enable support for more than 2GB of memory for omap5 with LPAE with
#address-cells
- Fix omap3-gta04 backlight PWM frequency until the PWM driver
- Revert am335x dts changes related to cpufreq as the driver changes
still have not merged and the dts changes broke cpufreq
* tag 'omap-for-v4.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "ARM: dts: dra7: Move to operating-points-v2 table"
Revert "ARM: dts: am33xx: Move to operating-points-v2 table and ti-cpufreq driver"
Revert "ARM: dts: am335x-boneblack: Enable 1GHz OPP for cpu"
ARM: dts: omap3-gta04: reduce panel backlight PWM frequency to 83Hz
ARM: dts: Add support for more than 2GB of memory for omap5
ARM: dts: am57xx-beagle-x15: Add support for rev B1
ARM: dts: am57xx-beagle-x15: Remove pinmux configurations for erratum i869
ARM: dts: Fix LEDs for igepv5
ARM: dts: Add power button support for igepv5
ARM: dts: Configure omap5 OTG ID pin
ARM: dts: ARM: dts: Fix omap5 SDIO dat1 interrupt
ARM: dts: Configure panda SDIO WLAN wakeirq
This serie allows to increase video resolutions and make audio
adjustment during a video playback for STiH407 family socs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Fw1N
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
Pull "STi clock improvement for video playback" from Patrice Chotard:
This serie allows to increase video resolutions and make audio
adjustment during a video playback for STiH407 family socs.
* tag 'sti-dt-for-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH410: clock configuration to address 720p and 1080p
ARM: dts: STi: STiH407: clock configuration to address 720p and 1080p
ARM: dts: STiH418: Enable synchronous clock mode for video clocks
ARM: dts: STiH410: Enable synchronous clock mode for video clocks
ARM: dts: STiH407: Enable synchronous clock mode for video clocks
ARM: dts: STiH418: Enable clock propagation for audio clocks
ARM: dts: STiH410: Enable clock propagation for audio clocks
ARM: dts: STiH407: Enable clock propagation for audio clocks
ARM: dts: STiH4xx: Simplify clock binding of STiH4xx platforms
Update gpio-cells and gpio specifier for STiH415/416
Add PWM capture support for STiH416 and STiH407 family
Add USB3 support for B2260
Add HVA support for STiH410
Add clk_ignore_unused in bootargs of B2260
Add Flexible Direct Memory Access (FDMA) support for STiH407 family
Add internal audio codec IP spport for STiH407 family
Add uniperif player/reader IP blocks for STiH407 family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zoto
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts update" from Patrice Chotard:
Update gpio-cells and gpio specifier for STiH415/416
Add PWM capture support for STiH416 and STiH407 family
Add USB3 support for B2260
Add HVA support for STiH410
Add clk_ignore_unused in bootargs of B2260
Add Flexible Direct Memory Access (FDMA) support for STiH407 family
Add internal audio codec IP spport for STiH407 family
Add uniperif player/reader IP blocks for STiH407 family
* tag 'sti-dt-for-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti: (22 commits)
ARM: DT: STi: stihxxx-b2120: Add DT nodes for STi audio card
ARM: STi: DT: STiH407: Add uniperif reader dt nodes
ARM: STi: DT: STiH407: Add uniperif player dt nodes
ARM: STi: DT: STiH407: Add sti-sasg-codec dt node
ARM: DT: STiH407: Add spdif_out pinctrl config
ARM: DT: STiH407: Add i2s_in pinctrl configuration
ARM: DT: STiH407: Add i2s_out pinctrl configuration
ARM: STi: DT: STiH407: Add FDMA driver dt nodes.
ARM: dts: STiH410: Add hva dt nodes
ARM: dts: STiH410-b2260: add clk_ignore_unused in bootargs
ARM: dts: STiH410-b2260: add USB3 node
ARM: dts: STiH416: Define the number of PWM Capture channels
ARM: dts: STiH416: Define PWM Capture clock
ARM: dts: STiH416: Declare PWM Capture data lines via Pinctrl
ARM: dts: STiH416: Supply PWM Capture IRQs
ARM: dts: STiH407: Declare PWM Capture data lines via Pinctrl
ARM: dts: STiH407: Supply PWM Capture IRQ
ARM: dts: STiH416-b2020e: update gpio specifier
ARM: dts: STiH41x-b2000: update gpio specifier
ARM: dts: STiHxxx-b2120: update gpio specifier
...
Here are a couple of bugfixes for v4.8-rc. Most of them have
actually been around for a while this time but for some reason
didn't get applied early on. The shmobile regulator fix is the
only one that isn't completely obvious.
device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- A new use of skeleton.dtsi on arm64 has crept in after that
was removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tYAb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple of bugfixes for v4.8-rc.
Most of them have actually been around for a while this time but for
some reason didn't get applied early on. The shmobile regulator fix
is the only one that isn't completely obvious.
Device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- a new use of skeleton.dtsi on arm64 has crept in after that was
removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
Code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
Maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: defconfig: Fix USB configuration
arm64: dts: Fix broken architected timer interrupt trigger
ARM: multi_v7_defconfig: update XILINX_VDMA
ARM64: dts: bcm: Use a symlink to R-Pi dtsi files from arch=arm
ARM: dts: Remove use of skeleton.dtsi from bcm283x.dtsi
ARM: dts: STiH407-family: Provide interconnect clock for consumption in ST SDHCI
ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)
ARM: shmobile: fix regulator quirk for Gen2
ARM: EXYNOS: Clear OF_POPULATED flag from PMU node in IRQ init callback
MAINTAINERS: Add myself as reviewer for Samsung Exynos support
Usage of DTS macros instead of hard-coded numbers makes code easier
to read. One does not have to remember which value means pull-up/down
or specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier
to read. One does not have to remember which value means pull-up/down
or specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier
to read. One does not have to remember which value means pull-up/down
or specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace duplicated macros in each DTSI file with a common macro coming
from header. Include the header in each pinctrl DTSI so further changes
could use it.
Although PIN_FUNC_SPC_2 does not bring much information about the
function itself, it still is more descriptive then hard-coded
number <2>.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl drive strength register on exynos4415 is 2-bit wide for each
pin. The pins for SD2 were configured with value of 4. The driver does
not validate the value so this overflow effectively set a bit 1 in
adjacent pins thus configuring them to drive strength 2x.
The author's intention was probably to set drive strength of 4x.
All other SD pins are configured with drive strength of 4x. Fix these
with same pattern.
Fixes: 9246e7ff24 ("ARM: dts: Add dts files for exynos4415 SoC")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl pull up/down register on exynos4210 is 2-bit wide for each
pin and it accepts only values of 0, 1 and 3. The pins sd4-bus-width8
were configured with value of 4. The driver does not validate the value
so this overflow effectively set a bit 1 in adjacent pins thus
configuring them to pull down.
The author's intention was probably to set drive strength of 4x. All
other bus-widths pins are configured with pull up and drive strength of
4x. Fix this one with same pattern.
Fixes: 87711d8c7c ("ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace duplicated macros in each DTSI file with a common macro coming
from header. Include the header in each pinctrl DTSI so further changes
could use it.
Although PIN_FUNC_SPC_2 does not bring much information about the
function itself, it still is more descriptive then hard-coded
number <2>.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It is necessary to properly configure these clocks in order
to address 720p and 1080p HDMI resolution.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
It is necessary to properly configure these clocks in order
to address 720p and 1080p HDMI resolution.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch enables the synchronous clock mode for video clocks
on STiH418 board.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch enables the synchronous clock mode for video clocks
on STiH410 board.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch enables the synchronous clock mode for video clocks
on STiH407 board.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch is used in the clock driver to apply a clock propagation
flag on the audio clocks of STiH418
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch is used in the clock driver to apply a clock propagation
flag on the audio clocks of STiH410
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch is used in the clock driver to apply a clock propagation
flag on the audio clocks of STiH407
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Commit d20f997b4d ("ARM: dts: am57xx-beagle-x15: Remove pinmux
configurations for erratum i869") fat fingered a change in which
basically replaced mmc2_pinctrl_default with mmc1_pinctrl_default. And
kernel dutifully reports conflict of usage.
[...]
pinctrl-single 4a003400.pinmux: pin 4a00376c.0 already requested by
4809c000.mmc; cannot claim for 480b4000.mmc
pinctrl-single 4a003400.pinmux: pin-219 (480b4000.mmc) status -22
pinctrl-single 4a003400.pinmux: could not request pin 219 (4a00376c.0)
from group mmc1_pins_default on device pinctrl-single
omap_hsmmc 480b4000.mmc: Error applying setting, reverse things back
omap_hsmmc 480b4000.mmc: could not initialize pin control state
[...]
But, thanks to the fact that we were in fact setting all the muxes in
U-Boot, all the MMC devices were still properly detected.
Fix the typo.
Fixes: d20f997b4d ("ARM: dts: am57xx-beagle-x15: Remove pinmux
configurations for erratum i869")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: removed timestamps and wrapped description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds DT support for the NAND connected to the SoC AEMIF.
Passed torture hashing a 40MB file on top of UBIFS using subpages.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[khilman: add back default partitions from an earlier patch]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7UMP
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DA850 device-tree enhancements include" from Sekhar Nori:
- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART
* tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Audio support via simple-card
ARM: dts: da850,da850-evm: Add an aemif node and use it for the NAND
ARM: dts: da850: Add basic DTS for the LCDK
ARM: dts: da850: Add missing pin muxing for the UARTs
ARM: dts: da850: Add new ECAP and EPWM bindings
This reverts commit f80bc97fd0.
The original commit updated the cpufreq operating points tables for
dra7xx but was merged before the driver making use of the node was
merged, which breaks the existing cpufreq implementation on the system,
so revert the patch until the ti-cpufreq driver is merged.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 4317be1162.
The original commit updated the cpufreq operating points tables for
am33xx but was merged before the driver making use of the node was
merged, which breaks the existing cpufreq implementation on the system,
so revert the patch until the ti-cpufreq driver is merged.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit c36e6ec904.
The original commit updated the cpufreq operating points tables for
am335x-boneblack but was merged before the driver making use of the node
was merged, which breaks the existing cpufreq implementation on the
system, so revert the patch until the ti-cpufreq driver is merged.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
please pull the following:
- Jon adds support for the Ethernet MAC DT nodes (AMAC) and provides the
following updates for Broadcom references boards:
* New Northstar Plus reference boards added: BCM958525er, BCM958522er,
BCM988312hr, BCM958623hr and BCM958622hr
* Add SATA nodes to the BCM958625hr and XMC boards
* Add I2C nodes to the XMC board
* Fixes the amount of RAM on BCM958625HR, BCM958625K and BCM958525XMC boards
* Add the GPIO reboot method for BCM958625hr and XMC boards
- Dhanajay adds PWM nodes for the Northstar Plus SoCs
- Rafal adds the USB 2.0 PHY to the BCM5301x Device Tree file include
- Stefan adds a missing USB clock to the BCM283x DT files, adds a DTSI file for
the USB host mode on BCM283x and finally documents and adds support for the
Raspberry Pi Zero
- Florian adds support for the Northstar Plus Switch Register Access block which
enables the integrated switch on these SoCs and enables the switch ports on the
BCM958625HR reference board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j84Q
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for v4.9,
please pull the following:
- Jon adds support for the Ethernet MAC DT nodes (AMAC) and provides the
following updates for Broadcom references boards:
* New Northstar Plus reference boards added: BCM958525er, BCM958522er,
BCM988312hr, BCM958623hr and BCM958622hr
* Add SATA nodes to the BCM958625hr and XMC boards
* Add I2C nodes to the XMC board
* Fixes the amount of RAM on BCM958625HR, BCM958625K and BCM958525XMC boards
* Add the GPIO reboot method for BCM958625hr and XMC boards
- Dhanajay adds PWM nodes for the Northstar Plus SoCs
- Rafal adds the USB 2.0 PHY to the BCM5301x Device Tree file include
- Stefan adds a missing USB clock to the BCM283x DT files, adds a DTSI file for
the USB host mode on BCM283x and finally documents and adds support for the
Raspberry Pi Zero
- Florian adds support for the Northstar Plus Switch Register Access block which
enables the integrated switch on these SoCs and enables the switch ports on the
BCM958625HR reference board
* tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux: (22 commits)
ARM: dts: bcm2835: Add Raspberry Pi Zero
DT: bindings: bcm: Add Raspberry Pi Zero
ARM: dts: bcm283x: Add dtsi for USB host mode
ARM: dts: bcm283x: Add missing USB clock
ARM: dts: NSP: Add new DT file for bcm958622hr
ARM: dts: NSP: Add new DT file for bcm958623hr
ARM: dts: NSP: Add new DT file for bcm988312hr
ARM: dts: NSP: Add new DT file for bcm958522er
ARM: dts: NSP: Add new DT file for bcm958525er
ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file
ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file
ARM: dts: NSP: Specify RAM amount for BCM958525XMC board
ARM: dts: NSP: Specify RAM amount for BCM958625K board
ARM: dts: NSP: Enable SATA and add i2c devices on XMC
ARM: dts: NSP: Enable SATA on bcm958625hr
ARM: dts: NSP: Correct RAM amount for BCM958625HR board
ARM: dts: NSP: Add PWM Support to DT
ARM: BCM5301X: Specify PHY of USB 2.0 in DT
ARM: dts: NSP: Add BCM958625HR switch ports
ARM: dts: NSP: Add Switch Register Access Block node
...
This helps to get 100% intensity closer to "always on".
It compensates for an effect of dmtimer which at 100% still emits short
"off" impulses and the startup-time of the DC/DC converter makes
backlight intensity not reach full scale. The lower the PWM frequency
is, the smaller is this effect.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Add and fix a bunch of clocks in the DTS corresponding
to the new clock support merged into the clk tree.
- Move the CLCD display configuration from boardfile to
device tree using the new CLCD support merged into the
fbdev tree.
- Cut some auxdata.
- Cut some static remappings.
- Move the sched_clock() counter to use syscon+regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXxogwAAoJEEEQszewGV1z2WoQAIpNj8akj2qHWfaZKUa5HTVH
YN2ukEkhpY8qXDw8ZjQVGMQ2VrHUCFWkwcYat8RPe7yfeZcEEkFMTgfTkq9h3P3g
15a+a4PuX2Prli/gzH3gq9VayHBOrUe+YAiy6qRbtVM6K7qwd9fBDWGYUBgC4i9p
7Y8lsyNTXXthtOnajlYVAxfFGTq67F2kZjHiCEagsWB6aLfT5Ixi/ZmCTs/GTfEf
Lon7XG8RQFo/3xatM/k4kjv/Bd8GzIW8UR/iZ5qnEOBIbcFSBWey9N0saiagZ8M1
vMmYjClMlunvX8L22EoC8ZOHcfF+YFeKpqbKehDmobY5qdi40yTse0CoVcFPaX7o
JZWZThOirsEb6q0iFH/Imno8dGWnWRG++h3ONx4KYbyJ8dOxJOwjbGtM23iT+SbF
JnceDpQ/oo5D84UEZhdonY0bemhkKhd9TADHlg0IHPo94dtD2VCsZalfLk7RyDyx
9fOZFBZv5y8khh9nX5BhBkDexw0LXXmSyzrkjVOKsuImsBaLFueZe8kTDHFHbRCm
MjYwLGRdmQIBCubdbjj1lxWk+xVDtvSonrT57a/A3+luAJutGbOdAeCUGtF3IzIY
uSgGVaExxD+ax/E9dWP6N1kPvBAtB7+jqQXOsX6kO39irFxoUBE6OhdyT4RsrSEN
J1FRkiDG5EH1rXiVpD8h
=kkO1
-----END PGP SIGNATURE-----
Merge tag 'integrator-armsoc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/late
Pull "This is a bunch of Integrator changes for v4.9" Linus Walleij:
- Add and fix a bunch of clocks in the DTS corresponding
to the new clock support merged into the clk tree.
- Move the CLCD display configuration from boardfile to
device tree using the new CLCD support merged into the
fbdev tree.
- Cut some auxdata.
- Cut some static remappings.
- Move the sched_clock() counter to use syscon+regmap.
* tag 'integrator-armsoc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: read counter using syscon/regmap
ARM: integrator: cut down on static maps
ARM: integrator: delete some auxdata
ARM: integrator: move CP CLCD display to DTS
ARM: dts: add the core module clocks to Integrator/CP
ARM: dts: Add the core module clocks to Integrator/AP
ARM: dts: add the Integrator/AP baseboard clocks
ARM: dts: set the 24MHz xtal as parent of the UART clock
The default PHY configuration disables most of the LEDs. The following
configures the ethernet activity LEDs as Netgear intended.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This is a router based on the mv88f5181 chipset.
http://www.netgear.com/support/product/WNR854T.aspxhttp://wiki.openwrt.org/toh/netgear/wnr854t
[gregory.clement@free-electrons.com:
- extract dt part from "arm: orion5x: Add DT-based support for Netgear
WNR854T"
- squashed "arm: orion5x: Alias uart0 to serial0 for all orion5x" into
this commit and move serial0 alias from dtsi to dts]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Common definitions for the SoC for board definitions to use.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
orion-wdt refuses to start without these properties defined, so lift
definitions out of kirkwood/dove.dtsi
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch enables the uniperif players 2 & 3 for b2120 boards
and also adds the "simple-audio-card" device node to interconnect
the SoC sound device and the codec.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the DT node for the uniperif reader
IP block found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the DT nodes for the uniperif player
IP blocks found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the dt node for the internal audio
codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the pinctrl config for the spidf out
pins used by the sasg codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_in pins
used by the uniperif reader IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_out pins
used by the uniperif player IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
These nodes are required to get the fdma driver working
on STiH407 based silicon.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Some omap5 variants have more than 2GB of memory available as
optional models. Let's update the dts files to use two address
cells similar to what dra7 is using with commit dae320ec31
("ARM: dts: DRA7: change address-cells and size-cells").
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N