This driver likely also supports earlier (RTL8196) and later (RTL93xx)
SoCs.
The SPI hardware in these SoCs is specifically intended for connecting NOR
bootflash chips, and only used for that in dozens of examined devices.
However boiled down to basics, it's really just a half-duplex SPI
controller.
The hardware appears to have a vestigial second chip-select control, but
it hasn't been seen in the wild and is thus not supported.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Link: https://lore.kernel.org/r/20210120135928.246054-3-bert@biot.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Commit 7a2da5d796 ("spi: fsl: Fix driver breakage when SPI_CS_HIGH
is not set in spi->mode") broke our MPC8309 board by effectively
inverting the boolean value passed to fsl_spi_cs_control. The
SPISEL_BOOT signal is used as chipselect, but it's not a gpio, so
we cannot rely on gpiolib handling the polarity.
Adapt to the new world order by inverting the logic here. This does
assume that the slave sitting at the SPISEL_BOOT is active low, but
should that ever turn out not to be the case, one can create a stub
gpiochip driver controlling a single gpio (or rather, a single "spo",
special-purpose output).
Fixes: 7a2da5d796 ("spi: fsl: Fix driver breakage when SPI_CS_HIGH is not set in spi->mode")
Cc: stable@vger.kernel.org
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20210130143545.505613-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
The double negative makes it hard to read "if (!ACPI_FAILURE(status))".
Replace it with "if (ACPI_SUCCESS(status))".
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The address mode is either 3 or 4 for the controller, which is configured
by the firmware and cannot be modified in the OS driver. Get the
firmware configuration and add address mode check in the .supports_op()
to block invalid operations.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1611740450-47975-3-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120161658.3820610-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Link: https://lore.kernel.org/r/20200227143931.20688-1-sergiu.cuciurean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Release master that have been previously allocated if the number of
chipselect is invalid.
Fixes: 8e04187c1b ("spi: altera: add SPI core parameters support via platform data.")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210120082635.49304-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Ericsson U300 platform was one of two ARM929 based SoC platforms for
mobile phones in ST-Ericsson after the merger of Ericsson with ST-NXP
into ST-Ericsson, the other one being the ST Nomadik.
The platform was not widely adopted in Linux based systems and was
replaced with the far superior ST-Ericsson U8500 in 2011, but Linus
Walleij kept maintaining the code for the whole time.
Linus continues to use the Nomadik machine, but decided to drop
u300 from the kernel as part of this year's spring cleaning.
Thanks for having maintained it all these years.
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdbJkiHR9FSfJTH_5d_qRU1__dRXHM1TL40iqNRKbGQfrQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The issue is that using SPI from a callback under the CCF lock will
deadlock, since this code uses clk_get_rate().
Fixes: c474b38665 ("spi: Add driver for Cadence SPI controller")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210114154217.51996-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 766c6b63aa ("spi: fix client driver breakages when using GPIO
descriptors") broke fsl spi driver.
As now we fully rely on gpiolib for handling the polarity of
chip selects, the driver shall not alter the GPIO value anymore
when SPI_CS_HIGH is not set in spi->mode.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6b51cc2bfbca70d3e9b9da7b7aa4c7a9d793ca0e.1610629002.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the struct spi_controller max_speed_hz. This is based on the
reported source clock frequency during probe. The maximum bus clock
is half the source clock (as per the code in bcm2835_spi_transfer_one).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210107164825.21919-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark,
This patch series makes the Renesas MSIOF SPI driver fill in actual
transfer speeds and controller limits, so the SPI core can take them
into account.
This has been tested on R-Car Gen2 and Gen3.
Thanks!
Geert Uytterhoeven (2):
spi: sh-msiof: Fill in spi_transfer.effective_speed_hz
spi: sh-msiof: Fill in controller speed limits
drivers/spi/spi-sh-msiof.c | 14 +++++++++++---
1 file changed, 11 insertions(+), 3 deletions(-)
--
2.25.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Add QSPI controller support for Intel LGM SoC.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also added compatible
Support for Intel platform.
dt-bindings: spi: cadence-qspi: Add support for Intel lgm-qspi
(earlier patch mail thread and Ack-by)
link: "https://lore.kernel.org/lkml/5d6d1b85.1c69fb81.96938.0315@mx.google.com/"
Reference:
https://lkml.org/lkml/2020/6/1/50
---
v9:
- Vignesh review comments address and update
- Retain the patchv4 move the binding documentation from mtd to spi
directory.
- Add intel's compatible string over the legacy documentation
- Remove unused variable, CQSPI_SUPPORTS_MULTI_CHIPSELECT macro and check
- YAML convertion patch alone dropped
v8:
- As Mark suggested to add the dt-bindings documentation patches
end of the series , so dropped.
v7:
- Rob's review comments address and fixed dt-schema warning
- Pratyush review comments address and update
- DAC bit reset to 0 and 1 (enable/disable)
- tested QSI-NOR flash mx25l12805d on LGM soc, it's working after disable DAC
- Linus suggested to use 'num-cs' prperty instead of 'num-chipselect'
v6:
- Rob's review comments update
- add compatible string in properly aligned
- remove cadence-qspi extra comaptible string in example
v5:
- Rob's review comments update
- const with single compatible string kept
v4:
- Rob's review comments update
- remove '|' no formatting to preserve
- child node attributes follows under 'properties' under '@[0-9a-f]+$'.
v3:
- Pratyush review comments update
- CQSPI_SUPPORTS_MULTI_CHIPSELECT macro used instead of cqspi->use_direct_mode
- disable DAC support placed in end of controller_init
v2:
- Rob's review comments update for dt-bindings
- add 'oneOf' for compatible selection
- drop un-neccessary descriptions
- add the cdns,is-decoded-cs and cdns,rclk-en properties as schema
- remove 'allOf' in not required place
- add AdditionalProperties false
- add minItems/maxItems for qspi reset attributes
resend-v1:
- As per Mark's suggestion , reorder the patch series 1-3 driver
support patches, series 4-6 dt-bindings patches.
v1:
- initial version
Ramuthevar Vadivel Murugan (5):
spi: cadence-quadspi: Add QSPI support for Intel LGM SoC
spi: cadence-quadspi: Disable the DAC for Intel LGM SoC
spi: cadence-quadspi: Add multi-chipselect support for Intel LGM SoC
spi: Move cadence-quadspi.txt to Documentation/devicetree/bindings/spi
dt-bindings: spi: cadence-qspi: Add support for Intel lgm-qspi
.../bindings/{mtd => spi}/cadence-quadspi.txt | 1 +
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-cadence-quadspi.c | 24 ++++++++++++++++++----
3 files changed, 22 insertions(+), 5 deletions(-)
rename Documentation/devicetree/bindings/{mtd => spi}/cadence-quadspi.txt (97%)
--
2.11.0
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Simplify stm32h7_spi_prepare_fthlv() function implementation,
no functional change intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Roman Guskov <rguskov@dh-electronics.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20210104123114.261596-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to force this to be trigger high here, as the firmware
properly configures the irq flags already. Drop it to save a line.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210112001301.687628-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we use concrete version to determine the max_cmd_dword.
New entries should be added for compatible hardwares of new version
or on new platform, otherwise the device will use 16 dwords instead
of 64 even if it supports, which will degrade the performance.
This will decrease the compatibility and the maintainability.
Drop the switch-case statement of the version checking. Only version
less than 0x351 supports maximum 16 command dwords.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1610526716-14882-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the controller speed limits, so the SPI core can use them for
validating SPI transfers, and adjust or reject transfers when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210113101916.1147695-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the effective bit rate used for transfers, so the SPI core can
calculate instead of estimate delays.
Restore "reverse Christmas tree" order of local variables while adding
new variables.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210113101916.1147695-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
On Intel Lightning Mountain(LGM) SoCs QSPI controller do not use
Direct Access Controller(DAC).
This patch adds a quirk to disable the Direct Access Controller
for data transfer instead it uses indirect data transfe
DAC bit resets to 1 so there is no need to explicitly set it.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Link: https://lore.kernel.org/r/20201124041840.31066-3-vadivel.muruganx.ramuthevar@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With CONFIG_PM_SLEEP disabled the rpcif_spi_pm_ops variable is still
referenced and thus increasing the size of kernel.
Fix this issue by adding CONFIG_PM_SLEEP #ifdef check around the .pm
assignment (image size is critical on RZ/A SoC's where the SRAM sizes
range 4~5 MiB).
Fixes: 9584fc95ca ("spi: rpc-if: Remove CONFIG_PM_SLEEP ifdefery")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210107145329.27966-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel test robot reports the following warning.
drivers/spi/spi-cadence-quadspi.c:966:24: warning: comparison of distinct pointer types ('typeof (len) *' (aka 'unsigned int *') and 'typeof (500UL) *' (aka 'unsigned long *')) [-Wcompare-distinct-pointer-types]
msecs_to_jiffies(max(len, 500UL)))) {
^~~~~~~~~~~~~~~
include/linux/minmax.h:58:19: note: expanded from macro 'max'
#define max(x, y) __careful_cmp(x, y, >)
^~~~~~~~~~~~~~~~~~~~~~
include/linux/minmax.h:42:24: note: expanded from macro '__careful_cmp'
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~~~~~~~
include/linux/minmax.h:32:4: note: expanded from macro '__safe_cmp'
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~~~~~~~
include/linux/minmax.h:18:28: note: expanded from macro '__typecheck'
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
1 warning generated.
This happens because size_t is unsigned long on 64-bit platforms like
arm64 but it is unsigned int on 32-bit platforms like arm. Omitting the
"UL" would result in a warning on 64-bit platforms. Squash it by type
casting the arguments to size_t using max_t(). This way builds on both
type of platforms can be satisfied. There is no chance of any truncation
since 500 is small enough to fit into both int and long.
Fixes: f453f29397 ("spi: cadence-quadspi: Wait at least 500 ms for direct reads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210108181457.30291-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a new warning report by build for make ARCH=MIPS allmodconfig:
drivers/spi/spi-cadence-quadspi.c: In function 'cqspi_direct_read_execute':
./include/linux/minmax.h:18:28: warning: comparison of distinct pointer types lacks a cast
18 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
| ^~
./include/linux/minmax.h:32:4: note: in expansion of macro '__typecheck'
32 | (__typecheck(x, y) && __no_side_effects(x, y))
| ^~~~~~~~~~~
./include/linux/minmax.h:42:24: note: in expansion of macro '__safe_cmp'
42 | __builtin_choose_expr(__safe_cmp(x, y), \
| ^~~~~~~~~~
./include/linux/minmax.h:58:19: note: in expansion of macro '__careful_cmp'
58 | #define max(x, y) __careful_cmp(x, y, >)
| ^~~~~~~~~~~~~
drivers/spi/spi-cadence-quadspi.c:1153:24: note: in expansion of macro 'max'
1153 | msecs_to_jiffies(max(len, 500UL)))) {
| ^~~
"len" is unsigned,however,"500" is unsigned long.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20210107115704.3835282-1-siyanteng@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
This series adds Tegra210, Tegra186, and Tegra194 Quad SPI driver and
enables Quad SPI on Jetson Nano and Jetson Xavier NX.
QSPI controller is available on Tegra210, Tegra186 and Tegra194.
Tegra186 and Tegra194 has additional feature of combined sequence mode
where command, address and data can all be transferred in a single transfer.
Combined sequence mode is useful only when using DMA mode transfer.
This series does not have combined sequence mode feature as Tegra186/Tegra194
GPCDMA driver is not upstreamed yet.
This series includes
- dt-binding document
- QSPI driver for Tegra210/Tegra186/Tegra194
- Enables QSPI on Jetson Nano and Jetson Xavier NX.
Delta between patch versions:
[v5]: Simplified implementation in Patch-0006
[v4]: Updated dummy cycles implementation based on v3 feedback
- Added dummy_data bit field int spi_transfer to indicate corresponding
transfer is dummy bytes transfer.
- Updated Tegra QSPI transfer_one_message to identify dummy transfer and
to use HW supported dummy bytes transfer when dummy cycles are with in
Tegra QSPI supported max HW dummy cycles otherwise fallsback to transfer
dummy bytes from software.
- Updated dt-bindings based on v3 feedback.
[v3]: v2 has some mixed patches sent out accidentally.
v3 sends proper patches with fixes mentioned in v2.
[v2]: below v1 feedback
- Added SPI_MASTER_USES_HW_DUMMY_CYCLES flag for controllers supporting
hardware dummy cycles and skips dummy bytes transfer from software for
these controllers.
- Updated dt-binding doc with tx/rx tap delay properties.
- Added qspi_out clock to dt-binding doc which will be used later with
ddr mode support.
- All other v1 feedback on some cleanup.
Sowjanya Komatineni (9):
dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM
dt-bindings: spi: Add Tegra Quad SPI device tree binding
MAINTAINERS: Add Tegra Quad SPI driver section
spi: tegra210-quad: Add support for Tegra210 QSPI controller
spi: spi-mem: Mark dummy transfers by setting dummy_data bit
spi: tegra210-quad: Add support for hardware dummy cycles transfer
arm64: tegra: Enable QSPI on Jetson Nano
arm64: tegra: Add QSPI nodes on Tegra194
arm64: tegra: Enable QSPI on Jetson Xavier NX
.../bindings/spi/nvidia,tegra210-quad.yaml | 117 ++
MAINTAINERS | 8 +
.../dts/nvidia/tegra194-p3509-0000+p3668-0000.dts | 12 +
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 28 +
arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts | 12 +
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 5 +-
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-mem.c | 1 +
drivers/spi/spi-tegra210-quad.c | 1410 ++++++++++++++++++++
include/dt-bindings/clock/tegra210-car.h | 2 +-
include/linux/spi/spi.h | 2 +
12 files changed, 1604 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
create mode 100644 drivers/spi/spi-tegra210-quad.c
--
2.7.4
Tegra Quad SPI controller hardware supports sending dummy bytes based
on programmed dummy clock cycles after the actual transfer bytes.
This patch adds this support of hardware dummy bytes transfer and
skips transfer of dummy bytes from the software.
For dummy cycles more than Tegra Quad SPI hardware maximum dummy
cycles limit, driver transfers dummy bytes from the software.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-7-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch marks dummy transfer by setting dummy_data bit to 1.
Controllers supporting dummy transfer by hardware use this bit field
to skip software transfer of dummy bytes and use hardware dummy bytes
transfer.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-6-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Double Transfer Rate (DTR) mode transfers data twice per clock cycle.
Add support for parsing DTR ops and set up the registers to allow it.
Most SPI NOR flashes expect 2 byte commands. Parse the 2-byte opcode
from SPI MEM and set it up in the CQSPI_REG_OP_EXT_LOWER register.
Increment the delay needed before issuing indirect writes because larger
delay is needed for DTR mode. With the current delay some writes end up
missing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-8-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing a direct read via DMA the timeout for completion is set
equal to the read length. This is fine for larger reads. For a small
read like the Read Status Register command, the timeout would be 1 or 2
milliseconds. This is not enough to cover the overhead needed in setting
up DMA.
Make sure the timeout is at least 500 ms to allow DMA ample time to
finish. For reads larger than 500 bytes, the timeout will continue to be
equal to the read length.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201222184425.7028-7-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default SPI MEM supports_op hook rejects DTR ops by default. Add a
simple supports_op hook that very closely imitates the SPI MEM one. It
will be extended in later commits to allow DTR ops.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-6-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI MEM deals with dummy bytes but the controller deals with dummy
cycles. Multiplying bytes by 8 is correct if the dummy phase uses 1S
mode since 1 byte will be sent in 8 cycles. But if the dummy phase uses
4S mode then 1 byte will be sent in 2 cycles.
To correctly translate dummy bytes to dummy cycles, the dummy buswidth
also needs to be taken into account. Divide 8 by the buswidth to get the
correct multiplier for getting the number of cycles.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a command does not have an address phase it goes via the STIG path.
The dummy cycles are not initialized for the STIG commands. As a result,
STIG commands with dummy cycles will not work.
Initialize the dummy cycle field before issuing the STIG command to make
sure it is sent correctly. Move the code to calculate dummy cycle value
to a separate function so it is not repeated twice. DTR support will add
some more logic here to it is worth it to extract it out in a function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-4-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit 9326e4f1e5 ("spi: Limit the spi device max speed to
controller's max speed"), the SPI device max speed is set to the
controller's max speed if it is larger. The Cadence QSPI controller does
not set the controller's max speed so it is left at its initial value of
0. This means the SPI device max speed is always set to 0.
The SPI device max speed is used to calculate the baud rate divider when
performing an operation. If this speed is 0, the default divider of 32
is used. No matter what speed is specified by the device tree property
'spi-max-frequency', the device will always operate at ref_clk / 32.
Fix this by setting master->max_speed_hz to the ref clock speed so the
correct divider can be calculated.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of the 'include/uapi/linux/spi/spi.h' header, the
type of the macros are enforced to 'unsigned long int' via the _BITUL()
macro.
This causes some -Wformat warnings in the spi-stm32 driver.
This patch adds a double-negation operator to the bit-masks. Essentially,
the important values for debugging are 0 or 1, while masking them directly
would show 0 or BIT(x) values.
This way, the type of the arguments are automatically re-cast.
Fixes: f7005142da ("spi: uapi: unify SPI modes into a single spi.h header")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210104143103.56510-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI driver for the Renesas RPC-IF is present on the RZ/G2
Series. Add that to the description.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210102115412.3402059-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The xfer waiting time is the result of xfer->len / xfer->speed_hz. This
patch makes the assumption of 100khz xfer speed if the xfer->speed_hz is
not assigned and stays 0. This avoids the divide by 0 issue and ensures
a reasonable tolerant waiting time.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/1609723749-3557-1-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/r/20201230145708.28544-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If spi->controller->max_speed_hz is zero, a non-zero spi->max_speed_hz
will be overwritten by zero. Make sure spi->controller->max_speed_hz
is not zero when clamping spi->max_speed_hz.
Put the spi->controller->max_speed_hz non-zero check higher in the if,
so that we avoid a superfluous init to zero when both spi->max_speed_hz
and spi->controller->max_speed_hz are zero.
Fixes: 9326e4f1e5 ("spi: Limit the spi device max speed to controller's max speed")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201216092321.413262-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the return value for altera_spi_txrx. It should return
1 for interrupt transfer mode, and return 0 for polling transfer mode.
The altera_spi_txrx() implements the spi_controller.transfer_one
callback. According to the spi-summary.rst, the transfer_one should
return 0 when transfer is finished, return 1 when transfer is still in
progress.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/1609219662-27057-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line
might be missing from an ADC while for a DAC the MISO/RX line may be
optional. This patch adds these two new modes: SPI_NO_TX and
SPI_NO_RX. This way, the drivers will be able to identify if any of
these two lines is missing and to adjust the transfers accordingly.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI devices, require toggling the CS every transferred byte.
Enable such possibility in the spi-orion driver.
Note that in order to use it, in the driver of a secondary device
attached to this controller, the SPI bus 'mode' field must be
updated with SPI_CS_WORD flag before calling spi_setup() routine.
In addition to that include a work-around - some devices, such as
certain models of SLIC (Subscriber Line Interface Card),
may require extra delay after CS toggling, so add a minimal
timing relaxation in relevant places.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-3-kostap@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-orion driver disables its clocks whenever it is not used.
In usual case during boot (i.e. using SPI flash) it is not a problem,
as the child device driver is present and probed along with
spi_register_master() execution.
However in case the child device driver is not ready
(e.g. when its type is module_spi_driver) the spi_setup() callback
can be called after the spi-orion probe. It may happen,
that as a result there will be an attempt to access controller's
registers with the clocks disabled.
Prevent such situations and make sure the clocks are on,
each time the spi_setup() is called.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-2-kostap@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
if cur_bpw <= 8 and xfer_len < 4 then the value of fthlv will be 1 and
SPI registers content may have been lost.
* If SPI data register is accessed as a 16-bit register and DSIZE <= 8bit,
better to select FTHLV = 2, 4, 6 etc
* If SPI data register is accessed as a 32-bit register and DSIZE > 8bit,
better to select FTHLV = 2, 4, 6 etc, while if DSIZE <= 8bit,
better to select FTHLV = 4, 8, 12 etc
Signed-off-by: Roman Guskov <rguskov@dh-electronics.com>
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201221123532.27272-1-rguskov@dh-electronics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're using geni to manage the chip select line (don't do it--use a
GPIO!) and we happen to get a timeout waiting for the chip select
command to be completed, no errors are printed even though things
might not be in the best shape. Let's add a print.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.4.I666b37646de9652cef438ac7c2c6c2053367fc6b@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If we get a timeout sending then this happens:
spi_transfer_one_message()
->transfer_one() AKA spi_geni_transfer_one()
setup_fifo_xfer()
mas->cur_xfer = non-NULL
spi_transfer_wait() => TIMES OUT
if (msg->status != -EINPROGRESS)
goto out
if (ret != 0 ...)
spi_set_cs()
->set_cs AKA spi_geni_set_cs()
# mas->cur_xfer is non-NULL
The above happens _before_ the SPI core calls ->handle_err() AKA
handle_fifo_timeout().
Unfortunately that won't work so well on geni. If we got a timeout
transferring then it's likely that our interrupt handler is blocked,
but we need that same interrupt handler to run and the command channel
to be unblocked in order to adjust the chip select. Trying to set the
chip select doesn't crash us but ends up confusing our state machine
and leads to messages like: Premature done. rx_rem = 32 bpw8
Let's just drop the chip select request in this case. We can detect
the case because cur_xfer is non-NULL--it would have been set to NULL
in the interrupt handler if the previous transfer had finished. Sure,
we might leave the chip select in the wrong state but it's likely it
was going to fail anyway and this avoids getting the driver even more
confused about what it's doing.
The SPI core in general assumes that setting chip select is a simple
operation that doesn't fail. Yet another reason to just reconfigure
the chip select line as GPIOs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.3.I07afdedcc49655c5d26880f8df9170aac5792378@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If we got a timeout when trying to send an abort command then it means
that we just got 3 timeouts in a row:
1. The original timeout that caused handle_fifo_timeout() to be
called.
2. A one second timeout waiting for the cancel command to finish.
3. A one second timeout waiting for the abort command to finish.
SPI is clocked by the controller, so nothing (aside from a hardware
fault or a totally broken sequencer) should be causing the actual
commands to fail in hardware. However, even though the hardware
itself is not expected to fail (and it'd be hard to predict how we
should handle things if it did), it's easy to hit the timeout case by
simply blocking our interrupt handler from running for a long period
of time. Obviously the system is in pretty bad shape if a interrupt
handler is blocked for > 2 seconds, but there are certainly bugs (even
bugs in other unrelated drivers) that can make this happen.
Let's make things a bit more robust against this case. If we fail to
abort we'll set a flag and then we'll block all future transfers until
we have no more interrupts pending.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.2.Ibade998ed587e070388b4bf58801f1107a40eb53@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7ba9bdcb91 ("spi: spi-geni-qcom: Don't keep a local state
variable") we changed handle_fifo_timeout() so that we set
"mas->cur_xfer" to NULL to make absolutely sure that we don't mess
with the buffers from the previous transfer in the timeout case.
Unfortunately, this caused the IRQ handler to dereference NULL in some
cases. One case:
CPU0 CPU1
---- ----
setup_fifo_xfer()
geni_se_setup_m_cmd()
<hardware starts transfer>
<transfer completes in hardware>
<hardware sets M_RX_FIFO_WATERMARK_EN in m_irq>
...
handle_fifo_timeout()
spin_lock_irq(mas->lock)
mas->cur_xfer = NULL
geni_se_cancel_m_cmd()
spin_unlock_irq(mas->lock)
geni_spi_isr()
spin_lock(mas->lock)
if (m_irq & M_RX_FIFO_WATERMARK_EN)
geni_spi_handle_rx()
mas->cur_xfer NULL dereference!
tl;dr: Seriously delayed interrupts for RX/TX can lead to timeout
handling setting mas->cur_xfer to NULL.
Let's check for the NULL transfer in the TX and RX cases and reset the
watermark or clear out the fifo respectively to put the hardware back
into a sane state.
NOTE: things still could get confused if we get timeouts all the way
through handle_fifo_timeout() and then start a new transfer because
interrupts from the old transfer / cancel / abort could still be
pending. A future patch will help this corner case.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.1.I99ee04f0cb823415df59bd4f550d6ff5756e43d6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Collected patches from the two series below and associated tags so they
can be merged in one pile through the spi tree. Merry December!
SPI: https://lore.kernel.org/r/20201202214935.1114381-1-swboyd@chromium.org
cros-ec: https://lore.kernel.org/r/20201203011649.1405292-1-swboyd@chromium.org
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Stephen Boyd (3):
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
spi: spi-geni-qcom: Use the new method of gpio CS control
drivers/platform/chrome/cros_ec_spi.c | 2 --
drivers/spi/spi-geni-qcom.c | 1 +
2 files changed, 1 insertion(+), 2 deletions(-)
base-commit: b650545978
--
https://chromeos.dev
Let's set the 'use_gpio_descriptors' field so that we use the new way of
requesting the CS GPIOs in the core. This allows us to avoid having to
configure the CS pins in "output" mode with an 'output-enable' pinctrl
setting.
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201204193540.3047030-4-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Canaan Kendryte K210 RISC-V SoC includes a DW apb_ssi v4 controller
which is documented to have a 32 words deep TX and RX FIFO. The FIFO
length detection in spi_hw_init() correctly detects this value.
However, when the controller RX FIFO is filled up to 32 entries
(RXFLR = 32), an RX FIFO overrun error occurs. This likely due to a
hardware bug which can be avoided by force setting the fifo_len field of
struct dw_spi to 31.
Define the dw_spi_canaan_k210_init() function to force set fifo_len to
31 when the device node compatible string is "canaan,k210-spi".
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-4-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward
define a 32-bits maximum transfer size synthesis parameter
(SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration
(SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32,
the layout of the ctrlr0 register changes, moving the data frame format
field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size
can be up to 32-bits.
To support this new format, introduce the DW SPI capability flag
DW_SPI_CAP_DFS32 to indicate that a controller is configured with
SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis
parameter not accessible through a register, the detection of this
parameter value is done in spi_hw_init() by writing and reading the
ctrlr0 register and testing the value of bits [3..0]. These bits are
ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection.
If a DFS32 capable SPI controller is detected, the new field dfs_offset
in struct dw_spi is set to SPI_DFS32_OFFSET (16).
dw_spi_update_config() is modified to set the data frame size field at
the correct position is the CTRLR0 register, as indicated by the
dfs_offset field of the dw_spi structure.
The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave
controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI
capability flag set. However, for these ssi controllers, the dfs_offset
field is set to 0 as before (as per specifications).
Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag
set, dw_spi_add_host() extends the value of bits_per_word_mask from
16-bits to 32-bits. dw_reader() and dw_writer() are also modified to
handle 32-bits iTX/RX FIFO words.
Suggested-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with the move of the atmel-quadspi driver under SPI,
the following error could be seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
1/4 fixes AHB accesses. The rest of the patches are small optimizations.
Tested on both sama5d2 and sam9x60.
Tudor Ambarus (4):
spi: atmel-quadspi: Fix AHB memory accesses
spi: atmel-quadspi: Drop superfluous set of QSPI_IFR_APBTFRTYP_READ
spi: atmel-quadspi: Write QSPI_IAR only when needed
spi: atmel-quadspi: Move common code outside of if else
drivers/spi/atmel-quadspi.c | 25 +++++++++++++------------
1 file changed, 13 insertions(+), 12 deletions(-)
--
2.25.1
base-commit: 3650b228f8
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
atmel_qspi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Piotr Bugalski <bugalski.piotr@gmail.com>
Link: https://lore.kernel.org/r/4b05c65cf6f1ea3251484fe9a00b4c65478a1ae3.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_master() fails on probe of the NPCM FIU
SPI driver, the clock "fiu->clk" is erroneously not unprepared and
disabled. Fix it.
Fixes: ace55c411b ("spi: npcm-fiu: add NPCM FIU controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.4+
Cc: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/9ae62f4e1cfe542bec57ac2743e6fca9f9548f55.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_controller() fails on probe of the
Qualcomm Atheros AR934x/QCA95xx SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Moreover, the controller's clock is enabled on probe but not disabled if
any of the subsequent probe steps fail.
Finally, there's an ordering issue in ar934x_spi_remove() wherein the
clock is disabled even though the controller is not yet unregistered.
It is unregistered after ar934x_spi_remove() by the devres framework.
As long as it is not unregistered, SPI transfers may still be ongoing
and disabling the clock may break them. It is not possible to use
devm_spi_register_controller() in this case, so move to the non-devm
variant.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 047980c582 ("spi: add driver for ar934x spi controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/1d58367d74d55741e0c2730a51a2b65012c8ab33.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to device_reset() or devm_spi_register_controller() fail on
probe of the MediaTek MT7621 SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Additionally, there's an ordering issue in mt7621_spi_remove() wherein
the spi_controller is unregistered after disabling the SYS clock.
The correct order is to call spi_unregister_controller() *before* this
teardown step because bus accesses may still be ongoing until that
function returns.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.17+
Link: https://lore.kernel.org/r/72b680796149f5fcda0b3f530ffb7ee73b04f224.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 702b15cb97 ("spi: mt7621: fix missing clk_disable_unprepare()
on error in mt7621_spi_probe") sought to disable the SYS clock on probe
errors, but only did so for 2 of 3 potentially failing calls: The clock
needs to be disabled on failure of devm_spi_register_controller() as
well.
Moreover, the commit purports to fix a bug in commit cbd66c626e ("spi:
mt7621: Move SPI driver out of staging") but in reality the bug has
existed since the driver was first introduced.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.17+: 702b15cb9712: spi: mt7621: fix missing clk_disable_unprepare() on error in mt7621_spi_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/36ad42760087952fb7c10aae7d2628547c26a7ec.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_gpiod_get_optional() fails on probe of the NXP
SC18IS602/603 SPI driver, the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: f99008013e ("spi: sc18is602: Add reset control via gpio pin.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Phil Reid <preid@electromag.com.au>
Link: https://lore.kernel.org/r/d5f715527b894b91d530fe11a86f51b3184a4e1a.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_clk_get(), devm_spi_register_master() or
clk_prepare_enable() fail on probe of the Mikrotik RB4xx SPI driver,
the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 05aec35787 ("spi: Add SPI driver for Mikrotik RB4xx series boards")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.2+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Bert Vermeulen <bert@biot.com>
Link: https://lore.kernel.org/r/369bf26d71927f60943b1d9d8f51810f00b0237d.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_master() fails on probe of the GPIO SPI
driver, the spi_master struct is erroneously not freed:
After allocating the spi_master, its reference count is 1. The driver
unconditionally decrements the reference count on unbind using a devm
action. Before calling devm_spi_register_master(), the driver
unconditionally increments the reference count because on success,
that function will decrement the reference count on unbind. However on
failure, devm_spi_register_master() does *not* decrement the reference
count, so the spi_master is leaked.
The issue was introduced by commits 8b797490b4 ("spi: gpio: Make sure
spi_master_put() is called in every error path") and 79567c1a32 ("spi:
gpio: Use devm_spi_register_master()"), which sought to plug leaks
introduced by 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO
descriptors") but missed this remaining leak.
The situation was later aggravated by commit d3b0ffa1d7 ("spi: gpio:
prevent memory leak in spi_gpio_probe"), which introduced a
use-after-free because it releases a reference on the spi_master if
devm_add_action_or_reset() fails even though the function already
does that.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.1-: 8b797490b4db: spi: gpio: Make sure spi_master_put() is called in every error path
Cc: <stable@vger.kernel.org> # v5.1-: 45beec351998: spi: bitbang: Introduce spi_bitbang_init()
Cc: <stable@vger.kernel.org> # v5.1-: 79567c1a321e: spi: gpio: Use devm_spi_register_master()
Cc: <stable@vger.kernel.org> # v5.4-: d3b0ffa1d75d: spi: gpio: prevent memory leak in spi_gpio_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/86eaed27431c3d709e3748eb76ceecbfc790dd37.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_controller() fails on probe of the
MediaTek SPI NOR driver, the spi_controller struct is erroneously not
freed.
Since commit a1daaa991e ("spi: spi-mtk-nor: use dma_alloc_coherent()
for bounce buffer"), the same happens if the call to
dmam_alloc_coherent() fails.
Since commit 3bfd9103c7 ("spi: spi-mtk-nor: Add power management
support"), the same happens if the call to mtk_nor_enable_clk() fails.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 881d1ee9fe ("spi: add support for mediatek spi-nor controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/d5b9f0289465394e73dedb8ec51e180a8f1dffc9.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_clk_get() or devm_ioremap_resource() fail on probe
of the Macronix SPI driver, the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: b942d80b0a ("spi: Add MXIC controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Mason Yang <masonccyang@mxic.com.tw>
Link: https://lore.kernel.org/r/4fa6857806e7e75741c05d057ac9df3564460114.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
rpcif_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: eb8d6d464a ("spi: add Renesas RPC-IF driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.9+
Cc: Sergei Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/c5da472c28021da2f6517441685cef033d40b140.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
pxa2xx_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master/slave() helper
which keeps the private data accessible until the driver has unbound.
Fixes: 32e5b57232 ("spi: pxa2xx: Fix controller unregister order")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v2.6.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v2.6.17+: 32e5b57232c0: spi: pxa2xx: Fix controller unregister order
Cc: <stable@vger.kernel.org> # v2.6.17+
Link: https://lore.kernel.org/r/5764b04d4a6e43069ebb7808f64c2f774ac6f193.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_sh_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 680c1305e2 ("spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v3.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v3.0+
Cc: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/6d97628b536baf01d5e3e39db61108f84d44c8b2.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
qcom_qspi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: f79a158d37 ("spi: spi-qcom-qspi: Use OPP API to set clk/perf state")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.9+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/b6d3c4dce571d78a532fd74f27def0d5dc8d8a24.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_geni_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Moreover, since commit 1a9e489e61 ("spi: spi-geni-qcom: Use OPP API to
set clk/perf state"), spi_geni_probe() leaks the spi_master allocation
if the calls to dev_pm_opp_set_clkname() or dev_pm_opp_of_add_table()
fail.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.20+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.20+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Girish Mahadevan <girishm@codeaurora.org>
Link: https://lore.kernel.org/r/dfa1d8c41b8acdfad87ec8654cd124e6e3cb3f31.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
davinci_spi_remove() accesses the driver's private data after it's been
freed with spi_master_put().
Fix by moving the spi_master_put() to the end of the function.
Fixes: fe5fd25409 ("spi: davinci: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@vger.kernel.org> # v4.7+
Link: https://lore.kernel.org/r/412f7eb1cf8990e0a3a2153f4c577298deab623e.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
QSPI_IFR is set as the last QSPI Instruction Frame register
regardless of the sama5d2 or sam9x60 version of the IP. Move
the writing of QSPI_IFR outside of the IP specific code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-5-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
That bit describes the APB transfer type. We are writing
serial memory registers via AHB acesses, that bit does not
make sense in the current context.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following error was seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
QSPI_IFR.TFRTYP was not set correctly. When data transfer is enabled
and one wants to access the serial memory through AHB in order to:
- read in the serial memory, but not a memory data, for example
a JEDEC-ID, QSPI_IFR.TFRTYP must be written to '0' (both sama5d2
and sam9x60).
- read in the serial memory, and particularly a memory data,
TFRTYP must be written to '1' (both sama5d2 and sam9x60).
- write in the serial memory, but not a memory data, for example
writing the configuration or the QSPI_SR, TFRTYP must be written
to '2' for sama5d2 and to '0' for sam9x60.
- write in the serial memory in particular to program a memory data,
TFRTYP must be written to '3' for sama5d2 and to '1' for sam9x60.
Fix the setting of the QSPI_IFR.TFRTYP field.
Fixes: 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Cc: <stable@vger.kernel.org> # v5.0+
Reported-by: Tom Burkart <tom@aussec.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-2-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/1607071357-33378-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs-gpios property is used in devicetree then ctlr->num_chipselect value
may be changed by spi_get_gpio_descs().
So use ctlr->max_native_cs instead of ctlr->num_chipselect to set SPI_MCR
Fixes: 4fcc7c2292 (spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR)
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20201201085916.63543-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
broke the use of the SPISEL_BOOT signal as a chip select on the
MPC8309.
pdata->max_chipselect, which becomes master->num_chipselect, must be
initialized to take into account the possibility that there's one more
chip select in use than the number of GPIO chip selects.
Cc: stable@vger.kernel.org # v5.4+
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201127152947.376-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
I mistakenly added the select attributes to the SPI_DW_BT1_DIRMAP config
instead of having them defined in SPI_DW_BT1. If the kernel doesn't have
the MULTIPLEXER and MUX_MMIO configs manually enabled and the
SPI_DW_BT1_DIRMAP config hasn't been selected, Baikal-T1 SPI device will
always fail to be probed by the driver. Fix that and the error reported by
the test robot:
>> ld.lld: error: undefined symbol: devm_mux_control_get
>>> referenced by spi-dw-bt1.c
>>> spi/spi-dw-bt1.o:(dw_spi_bt1_sys_init) in archive drivers/built-in.a
by moving the MULTIPLEXER/MUX_MMIO configs selection to the SPI_DW_BT1
config.
Link: https://lore.kernel.org/lkml/202011161745.uYRlekse-lkp@intel.com/
Link: https://lore.kernel.org/linux-spi/20201116040721.8001-1-rdunlap@infradead.org/
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201127144612.4204-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
fixed the coccicheck:
drivers/spi/spi-dw-bt1.c:220:27-30: ERROR: Missing
resource_size with mem.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/1606114975-31362-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI DW memory ops support was introduced, there was a check for
excluding controllers which supplied their own CS function. Even so,
the mem_ops pointer is *always* presented to the SPI core.
This causes the SPI core sanity check in spi_controller_check_ops() to
refuse registration, since a mem_ops pointer is being supplied without
an exec_op member function.
The end result is failure of the SPI DW driver on sparx5 and similar
platforms.
The fix in the core SPI DW driver is to avoid presenting the mem_ops
pointer if the exec_op function is not set.
Fixes: 6423207e57 (spi: dw: Add memory operations support)
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201120213414.339701-1-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shutdown bus function might be called on the unbound device, so add a
check if there is a driver before calling its shutdown function.
This fixes following kernel panic obserbed during system reboot:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018
...
Call trace:
spi_shutdown+0x10/0x38
kernel_restart_prepare+0x34/0x40
kernel_restart+0x14/0x88
__do_sys_reboot+0x148/0x248
__arm64_sys_reboot+0x1c/0x28
el0_svc_common.constprop.3+0x74/0x198
do_el0_svc+0x20/0x98
el0_sync_handler+0x140/0x1a8
el0_sync+0x140/0x180
Code: f9403402 d1008041 f100005f 9a9f1021 (f9400c21)
---[ end trace 266c07205a2d632e ]---
Fixes: 9db34ee64c (spi: Use bus_type functions for probe, remove and shutdown)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201124131523.32287-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If set active without increase the usage count of pm, the dont use
autosuspend function will call the suspend callback to close the two
clocks of spi because the usage count is reduced to -1.
This will cause the warning dump below when the defer-probe occurs.
[ 129.379701] ecspi2_root_clk already disabled
[ 129.384005] WARNING: CPU: 1 PID: 33 at drivers/clk/clk.c:952 clk_core_disable+0xa4/0xb0
So add the get noresume function before set active.
Fixes: 43b6bf406c spi: imx: fix runtime pm support for !CONFIG_PM
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20201124085247.18025-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Given the case that bootloader(such as UEFI)'s FSPI driver might not
handle all interrupts before loading kernel, those legacy interrupts
would assert immidiately once kernel's FSPI driver enable them. Further,
if it was FSPI_INTR_IPCMDDONE, the irq handler nxp_fspi_irq_handler()
would call complete(&f->c) to notify others. However, f->c might not be
initialized yet at that time, then cause kernel panic.
Of cause, we should fix this issue within bootloader. But it would be
better to have this pacth to make dirver more robust (by clearing all
interrupt status bits before enabling interrupts).
Suggested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201123025715.14635-1-ran.wang_1@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I've discovered that due to the recent commit 49d7d695ca ("spi: dw:
Explicitly de-assert CS on SPI transfer completion") a concurrent usage of
the spidev devices with different chip-selects causes the "SPI transfer
timed out" error. The root cause of the problem has turned to be in a race
condition of the SPI-transfer execution procedure and the spi_setup()
method being called at the same time. In particular in calling the
spi_set_cs(false) while there is an SPI-transfer being executed. In my
case due to the commit cited above all CSs get to be switched off by
calling the spi_setup() for /dev/spidev0.1 while there is an concurrent
SPI-transfer execution performed on /dev/spidev0.0. Of course a situation
of the spi_setup() being called while there is an SPI-transfer being
executed for two different SPI peripheral devices of the same controller
may happen not only for the spidev driver, but for instance for MMC SPI +
some another device, or spi_setup() being called from an SPI-peripheral
probe method while some other device has already been probed and is being
used by a corresponding driver...
Of course I could have provided a fix affecting the DW APB SSI driver
only, for instance, by creating a mutual exclusive access to the set_cs
callback and setting/clearing only the bit responsible for the
corresponding chip-select. But after a short research I've discovered that
the problem most likely affects a lot of the other drivers:
- drivers/spi/spi-sun4i.c - RMW the chip-select register;
- drivers/spi/spi-rockchip.c - RMW the chip-select register;
- drivers/spi/spi-qup.c - RMW a generic force-CS flag in a CSR.
- drivers/spi/spi-sifive.c - set a generic CS-mode flag in a CSR.
- drivers/spi/spi-bcm63xx-hsspi.c - uses an internal mutex to serialize
the bus config changes, but still isn't protected from the race
condition described above;
- drivers/spi/spi-geni-qcom.c - RMW a chip-select internal flag and set the
CS state in HW;
- drivers/spi/spi-orion.c - RMW a chip-select register;
- drivers/spi/spi-cadence.c - RMW a chip-select register;
- drivers/spi/spi-armada-3700.c - RMW a chip-select register;
- drivers/spi/spi-lantiq-ssc.c - overwrites the chip-select register;
- drivers/spi/spi-sun6i.c - RMW a chip-select register;
- drivers/spi/spi-synquacer.c - RMW a chip-select register;
- drivers/spi/spi-altera.c - directly sets the chip-select state;
- drivers/spi/spi-omap2-mcspi.c - RMW an internally cached CS state and
writes it to HW;
- drivers/spi/spi-mt65xx.c - RMW some CSR;
- drivers/spi/spi-jcore.c - directly sets the chip-selects state;
- drivers/spi/spi-mt7621.c - RMW a chip-select register;
I could have missed some drivers, but a scale of the problem is obvious.
As you can see most of the drivers perform an unprotected
Read-modify-write chip-select register modification in the set_cs callback.
Seeing the spi_setup() function is calling the spi_set_cs() and it can be
executed concurrently with SPI-transfers exec procedure, which also calls
spi_set_cs() in the SPI core spi_transfer_one_message() method, the race
condition of the register modification turns to be obvious.
To sum up the problem denoted above affects each driver for a controller
having more than one chip-select lane and which:
1) performs the RMW to some CS-related register with no serialization;
2) directly disables any CS on spi_set_cs(dev, false).
* the later is the case of the DW APB SSI driver.
The controllers which equipped with a single CS theoretically can also
experience the problem, but in practice will not since normally the
spi_setup() isn't called concurrently with the SPI-transfers executed on
the same SPI peripheral device.
In order to generically fix the denoted bug I'd suggest to serialize an
access to the controller IO by taking the IO mutex in the spi_setup()
callback. The mutex is held while there is an SPI communication going on
on the SPI-bus of the corresponding SPI-controller. So calling the
spi_setup() method and disabling/updating the CS state within it would be
safe while there is no any SPI-transfers being executed. Also note I
suppose it would be safer to protect the spi_controller->setup() callback
invocation too, seeing some of the SPI-controller drivers update a HW
state in there.
Fixes: 49d7d695ca ("spi: dw: Explicitly de-assert CS on SPI transfer completion")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201117094517.5654-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver core ignores the return value of struct device_driver::remove
(because in general there is nothing that can be done about that). So
add a warning when an spi driver returns an error.
This simplifies the quest to make struct device_driver::remove return void.
A consequent change would be to make struct spi_driver::remove return void,
but I'm keeping this quest for later (or someone else).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The eventual goal is to get rid of the callbacks in struct
device_driver. Other than not using driver callbacks there should be no
side effect of this patch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Consider an spi driver with a .probe but without a .remove callback (e.g.
rtc-ds1347). The function spi_drv_probe() is called to bind a device and
so dev_pm_domain_attach() is called. As there is no remove callback
spi_drv_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use both spi_drv_probe() and spi_drv_remove() and
make them handle the respective callback not being set. This has the
side effect that for a (hypothetical) driver that has neither .probe nor
remove the clk and pm domain setup is done.
Fixes: 33cf00e570 ("spi: attach/detach SPI device to the ACPI power domain")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in mxs_spi_probe, so we should fix it.
Fixes: b7969caf41 ("spi: mxs: implement runtime pm")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201106012421.95420-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201116202606.29888-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to of_match_device(), of_alias_get_id(),
devm_ioremap_resource(), devm_regmap_init_mmio() or devm_clk_get()
fail on probe of the NPCM FIU SPI driver, the spi_controller struct is
erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: ace55c411b ("spi: npcm-fiu: add NPCM FIU controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.4+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.4+
Cc: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/a420c23a363a3bc9aa684c6e790c32a8af106d17.1605512876.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It turns out the IRQs most like can be unmasked before the controller is
enabled with no problematic consequences. The manual doesn't explicitly
state that, but the examples perform the controller initialization
procedure in that order. So the commit da8f58909e ("spi: dw: Unmask IRQs
after enabling the chip") hasn't been that required as I thought. But
anyway setting the IRQs up after the chip enabling still worth adding
since it has simplified the code a bit. The problem is that it has
introduced a potential bug. The transfer handler pointer is now
initialized after the IRQs are enabled. That may and eventually will cause
an invalid or uninitialized callback invocation. Fix that just by
performing the callback initialization before the IRQ unmask procedure.
Fixes: da8f58909e ("spi: dw: Unmask IRQs after enabling the chip")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201117094054.4696-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
MT8192 spi-nor is an independent sub system, we need extra control axi
bus clock for it. Add support for the additional axi clock to allow it
to be configured appropriately.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Tested-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/1605084902-13151-2-git-send-email-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return the error code from
devm_reset_control_get_optional_exclusive() instaed of 0
in cqspi_probe().
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201116141836.2970579-1-chengzhihao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc47 ("spi: bcm2835aux: Fix use-after-free on unbind")
Link: https://github.com/ClangBuiltLinux/linux/issues/1199
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's my proposal to fix the use-after-free bugs reported by
Sascha Hauer and Florian Fainelli:
I scrutinized all SPI drivers in the v5.10 tree:
* There are 9 drivers with a use-after-free in the ->remove() hook
caused by accessing driver private data after spi_unregister_controller().
* There are 8 drivers which leak the spi_controller in the ->probe()
error path because of a missing spi_controller_put().
I'm introducing devm_spi_alloc_master/slave() which automatically
calls spi_controller_put() on ->remove(). This fixes both classes
of bugs while at the same time reducing code amount and complexity
in the ->probe() hook.
I propose that spi_controller_unregister() should no longer release
a reference on the spi_controller. Instead, drivers need to either
do it themselves or use one of the devm functions introduced herein.
The vast majority of drivers can be converted to the devm functions.
See the commit message of patch [1/4] for the rationale and details.
Enclosed are patches for 3 Broadcom drivers.
Patches for the other drivers are on this branch:
https://github.com/l1k/linux/commits/spi_fixes
@Florian Fainelli: Could you verify that there are no KASAN splats or
leaks with these patches? Unfortunately I do not have any SPI-capable
hardware at my disposal right now, so can only compile-test. You may
want to augment spi_controller_release() with a printk() to log when
the spi_controller is freed.
@Mark Brown: Patches [2/4] to [4/4] reference the SHA-1 of patch [1/4]
in their stable tags. Because the hash is unknown to me until you apply
the patch, I've used "123456789abc" as a placeholder. You'll have to
replace the hash if/when applying. Alternatively, only apply patch [1/4]
and I'll repost the other patches with the hash fixed up.
Thanks!
Lukas Wunner (4):
spi: Introduce device-managed SPI controller allocation
spi: bcm2835: Fix use-after-free on unbind
spi: bcm2835aux: Fix use-after-free on unbind
spi: bcm-qspi: Fix use-after-free on unbind
drivers/spi/spi-bcm-qspi.c | 34 ++++++++-------------
drivers/spi/spi-bcm2835.c | 24 +++++----------
drivers/spi/spi-bcm2835aux.c | 21 +++++--------
drivers/spi/spi.c | 58 +++++++++++++++++++++++++++++++++++-
include/linux/spi/spi.h | 19 ++++++++++++
5 files changed, 103 insertions(+), 53 deletions(-)
--
2.28.0
Normally the last reference on an spi_controller is released by
spi_unregister_controller(). In the case of the i.MX lpspi driver,
the spi_controller is registered with devm_spi_register_controller(),
so spi_unregister_controller() is invoked automatically after the driver
has unbound.
However the driver already releases the last reference in
fsl_lpspi_remove() through a gratuitous call to spi_master_put(),
causing a use-after-free when spi_unregister_controller() is
subsequently invoked by the devres framework.
Fix by dropping the superfluous spi_master_put().
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.2+
Cc: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/ab3c0b18bd820501a12c85e440006e09ec0e275f.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_platform_ioremap_resource(), irq_of_parse_and_map()
or devm_request_irq() fail on probe of the ST SSC4 SPI driver, the
runtime PM disable depth is incremented even though it was not
decremented before. Fix it.
Fixes: cd050abeba ("spi: st-ssc4: add missed pm_runtime_disable")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.5+
Cc: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/fbe8768c30dc829e2d77eabe7be062ca22f84024.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_request_irq() or devm_spi_register_master() fail
on probe of the PIC32 SPI driver, the DMA channels requested by
pic32_spi_dma_prep() are erroneously not released. Plug the leak.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.7+
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Link: https://lore.kernel.org/r/9624250e3a7aa61274b38219a62375bac1def637.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to platform_get_irq() or devm_request_irq() fail on probe
of the SynQuacer SPI driver, the clock "sspi->clk" is erroneously not
unprepared and disabled.
If the clock rate "master->max_speed_hz" cannot be determined, the same
happens and in addition the spi_master struct is not freed.
Fix it.
Fixes: b0823ee35c ("spi: Add spi driver for Socionext SynQuacer platform")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.3+
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Link: https://lore.kernel.org/r/232281df1ab91d8f0f553a62d5f97fc264ace4da.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Moreover, since commit 0392727c26 ("spi: bcm-qspi: Handle clock probe
deferral"), bcm_qspi_probe() leaks the spi_master allocation if the call
to devm_clk_get_optional() fails.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 123456789abc: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/5e31a9a59fd1c0d0b795b2fe219f25e5ee855f9d.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2835aux_spi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: b9dd3f6d41 ("spi: bcm2835aux: Fix controller unregister order")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.4+: 123456789abc: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.4+: b9dd3f6d4172: spi: bcm2835aux: Fix controller unregister order
Cc: <stable@vger.kernel.org> # v4.4+
Link: https://lore.kernel.org/r/b290b06357d0c0bdee9cecc539b840a90630f101.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2835_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: f8043872e7 ("spi: add driver for BCM2835")
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v3.10+: 123456789abc: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v3.10+
Cc: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/ad66e0a0ad96feb848814842ecf5b6a4539ef35c.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in sprd_spi_remove, so we should fix it.
Fixes: e7d973a31c ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20201106015035.139574-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case that the SPI mux isn't set, the transfer_one_message
function returns without finalizing the message. This means that
the transfer never completes, resulting in hung tasks and an
eventual kernel panic. Fix it by finalizing the transfer in this
case.
Fixes: 9211a441e6 ("spi: fsi: Check mux status before transfers")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201110214736.25718-1-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
introduced the optional use of GPIO descriptors for chip selects.
A side-effect of this change: when a SPI bus uses GPIO descriptors,
all its client devices have SPI_CS_HIGH set in spi->mode. This flag is
required for the SPI bus to operate correctly.
This unfortunately breaks many client drivers, which use the following
pattern to configure their underlying SPI bus:
static int client_device_probe(struct spi_device *spi)
{
...
spi->mode = SPI_MODE_0;
spi->bits_per_word = 8;
err = spi_setup(spi);
..
}
In short, many client drivers overwrite the SPI_CS_HIGH bit in
spi->mode, and break the underlying SPI bus driver.
This is especially true for Freescale/NXP imx ecspi, where large
numbers of spi client drivers now no longer work.
Proposed fix:
-------------
When using gpio descriptors, depend on gpiolib to handle CS polarity.
Existing quirks in gpiolib ensure that this is handled correctly.
Existing gpiolib behaviour will force the polarity of any chip-select
gpiod to active-high (if 'spi-active-high' devicetree prop present) or
active-low (if 'spi-active-high' absent). Irrespective of whether
the gpio is marked GPIO_ACTIVE_[HIGH|LOW] in the devicetree.
Loose ends:
-----------
If this fix is applied:
- is commit 138c9c32f0
("spi: spidev: Fix CS polarity if GPIO descriptors are used")
still necessary / correct ?
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201106150706.29089-1-TheSven73@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in callers(spi_imx_prepare_message and
spi_imx_remove), so we should fix it.
Fixes: 525c9e5a32 ("spi: imx: enable runtime pm support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102145835.4765-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to of_device_get_match_data() fails on probe of the Atmel
QuadSPI driver, the clock "aq->pclk" is erroneously not unprepared and
disabled. Fix it.
Fixes: 2e5c888873 ("spi: atmel-quadspi: add support for sam9x60 qspi controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.1+
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/8f8dc2815aa97b2378528f08f923bf81e19611f0.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from bcm63xx_hsspi_resume in the error handling case when
fails to prepare and enable bs->pll_clk.
Fixes: 0fd85869c2 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103074911.195530-1-miaoqinglang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in two callers(tegra_spi_setup and
tegra_spi_resume), so we should fix it.
Fixes: f333a331ad ("spi/tegra114: add spi driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201103141306.5607-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in tegra_sflash_resume, so we should fix it.
Fixes: 8528547bcc ("spi: tegra: add spi driver for sflash controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201103141323.5841-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in two callers(tegra_slink_setup and
tegra_slink_resume), so we should fix it.
Fixes: dc4dc36056 ("spi: tegra: add spi driver for SLINK controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201103141345.6188-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from mt7621_spi_probe in the error handling case.
Fixes: cbd66c626e ("spi: mt7621: Move SPI driver out of staging")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103074912.195576-1-miaoqinglang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in ti_qspi_setup, so we should fix it.
Fixes: 505a14954e ("spi/qspi: Add qspi flash controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201103140947.3815-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in two callers(stm32_qspi_exec_op and
stm32_qspi_setup), so we should fix it.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20201106015357.141235-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Removing the duplicate gpio chip select level handling in
bcm2835_spi_setup() left the lflags variable uninitialized. Avoid trhe
use of such variable by passing default flags to
gpiochip_request_own_desc().
Fixes: 5e31ba0c05 ("spi: bcm2835: fix gpio cs level inversion")
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201105090615.620315-1-martin@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in stm32_spi_resume, so we should fix it.
Fixes: db96bf976a ("spi: stm32: fixes suspend/resume management")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/20201106015217.140476-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in spi_mem_access_start, so we should fix it.
Fixes: f86c24f479 ("spi: spi-mem: Split spi_mem_exec_op() code")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201103140910.3482-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 530b5affc6 ("spi: fsl-dspi: fix use-after-free in
remove path"), this driver causes a "NULL pointer dereference"
in dspi_suspend/resume.
This is because since this commit, the drivers private data point to
"dspi" instead of "ctlr", the codes in suspend and resume func were
not modified correspondly.
Fixes: 530b5affc6 ("spi: fsl-dspi: fix use-after-free in remove path")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201103020546.1822-1-qiang.zhao@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix smatch warning:
drivers/spi/spi-mem.c:746 spi_mem_probe() warn: passing zero to 'PTR_ERR'
Fixes: 5d27a9c8ea ("spi: spi-mem: Extend the SPI mem interface to set a custom memory name")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20201031033042.42892-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in img_spfi_resume, so we should fix it.
Fixes: deba25800a ("spi: Add driver for IMG SPFI controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102145651.3875-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IP's DMA capabilities are described in the SoC dtsi, to spare
users duplicating the DMA bindings in their board device tree. Users
that don't want to use DMA, have to overwrite the DMA bindings in
their board device tree. An example is:
commit ddcdaeb882 ("ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and UART flx4 functions")
When the DMA bindings are overwritten, one could see on the console:
atmel_spi fc018400.spi: error -ENODEV: No TX DMA channel, DMA is disabled
atmel_spi fc018400.spi: Atmel SPI Controller using PIO only
Choosing to not use DMA is not a reason to print an error message.
More, the user is already informed when PIO is used: "Atmel SPI Controller
using PIO only". Downgrade to dev_dbg when dma_request_chan() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201030121116.869105-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The work on improving gpio chip-select in spi core, and the following
fixes, has caused the bcm2835 spi driver to use wrong levels. Fix this
by simply removing level handling in the bcm2835 driver, and let the
core do its work.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201014090230.2706810-1-martin@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If SPI is used for periodic polling any sensor, significant delays
sometimes appear. Switching on module clocks during resume lead to delays.
Enabling autosuspend mode causes the controller to not suspend between
SPI transfers and the delays disappear.
The commit also remove unnecessary call to pm_runtime_idle() used
to explicit put device to suspended state. Without pm_runtime_idle() PM
core will put device in the suspended state just after probe() returns.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201019150343.2520-1-akochetkov@lintech.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
If SPI is used for periodic polling any sensor, significant delays
sometimes appear. Switching on module clocks during resume lead to delays.
Enabling autosuspend mode causes the controller to not suspend between
SPI transfers and the delays disappear.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Link: https://lore.kernel.org/r/20201016085014.31667-1-al.kochet@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA-based transfer will be enabled if data length is larger than FIFO size
(64 bytes for A64). This greatly reduce number of interrupts for
transferring data.
For smaller data size PIO mode will be used. In PIO mode whole buffer will
be loaded into FIFO.
If driver failed to request DMA channels then it fallback for PIO mode.
Tested on SOPINE (https://www.pine64.org/sopine/)
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201022075221.23332-1-akochetkov@lintech.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
525c9e5a32 introduced pm_runtime support for the i.MX SPI driver. With
this pm_runtime is used to bring up the clocks initially. When CONFIG_PM
is disabled the clocks are no longer enabled and the driver doesn't work
anymore. Fix this by enabling the clocks in the probe function and
telling pm_runtime that the device is active using
pm_runtime_set_active().
Fixes: 525c9e5a32 spi: imx: enable runtime pm support
Tested-by: Christian Eggers <ceggers@arri.de> [tested for !CONFIG_PM only]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20201021104513.21560-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The amount of changes is smaller at this round (what a surprise),
but lots of activity is seen. Most of changes are about ASoC
driver development, especially Intel platforms.
Here are some highlights:
General:
* Replace all tasklet usages with other alternatives
* Cleanup of the ASoC error unwinding code
* Fixes for trivial issues caught by static checker
* Spell fixes allover the places
ALSA Core:
* Lockdep fix for control devices
* Fix for potential OSS sequencer mutex stalls
HD-audio and USB-audio:
* SoundBlaster AE-7 support
* Changes in quirk table for the rename handling
* Quirks for HP and ASUS machines, Pioneer DJ DJM-250MK2.
ASoC:
* Lots of updates for Intel SOF and SoundWire enablement
* Replacement of the DSP driver for some older x86 systems;
the new code was written from scratch, better maintenance
expected
* Helpers for parsing auxiluary devices from the device tree
* New support for AllWinner A64, Cirrus Logic CS4234, Mediatek
MT6359 Microchip S/PDIF TX and RX controllers, Realtek RT1015P,
and Texas Instruments J721E, TAS2110, TAS2564 and TAS2764
-----BEGIN PGP SIGNATURE-----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=nWAp
-----END PGP SIGNATURE-----
Merge tag 'sound-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The amount of changes is smaller at this round (what a surprise), but
lots of activity is seen. Most of changes are about ASoC driver
development, especially Intel platforms. Here are some highlights:
General:
- Replace all tasklet usages with other alternatives
- Cleanup of the ASoC error unwinding code
- Fixes for trivial issues caught by static checker
- Spell fixes allover the places
ALSA Core:
- Lockdep fix for control devices
- Fix for potential OSS sequencer mutex stalls
HD-audio and USB-audio:
- SoundBlaster AE-7 support
- Changes in quirk table for the rename handling
- Quirks for HP and ASUS machines, Pioneer DJ DJM-250MK2.
ASoC:
- Lots of updates for Intel SOF and SoundWire enablement
- Replacement of the DSP driver for some older x86 systems; the new
code was written from scratch, better maintenance expected
- Helpers for parsing auxiluary devices from the device tree
- New support for AllWinner A64, Cirrus Logic CS4234, Mediatek MT6359
Microchip S/PDIF TX and RX controllers, Realtek RT1015P, and Texas
Instruments J721E, TAS2110, TAS2564 and TAS2764"
* tag 'sound-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (498 commits)
ALSA: hda/hdmi: fix incorrect locking in hdmi_pcm_close
ALSA: hda: fix jack detection with Realtek codecs when in D3
ALSA: fireworks: use semicolons rather than commas to separate statements
ALSA: hda: use semicolons rather than commas to separate statements
ALSA: hda/i915 - fix list corruption with concurrent probes
ASoC: dmaengine: Document support for TX only or RX only streams
ASoC: mchp-spdiftx: remove 'TX' from playback stream name
ASoC: ti: davinci-mcasp: Use &pdev->dev for early dev_warn
ASoC: tas2764: Add the driver for the TAS2764
dt-bindings: tas2764: Add the TAS2764 binding doc
ASoC: Intel: catpt: Add explicit DMADEVICES kconfig dependency
ASoC: Intel: catpt: Fix compilation when CONFIG_MODULES is disabled
ASoC: stm32: dfsdm: add actual resolution trace
ASoC: stm32: dfsdm: change rate limits
ASoC: qcom: sc7180: Add support for audio over DP
Asoc: qcom: lpass-platform : Increase buffer size
ASoC: qcom: Add support for lpass hdmi driver
Asoc: qcom: lpass:Update lpaif_dmactl members order
Asoc:qcom:lpass-cpu:Update dts property read API
ASoC: dt-bindings: Add dt binding for lpass hdmi
...
Baikal-T1 is equipped with three DW APB SSI-based MMIO SPI controllers.
Two of them are pretty much normal: with IRQ, DMA, FIFOs of 64 words
depth, 4x CSs, but the third one as being a part of the Baikal-T1 System
Boot Controller has got a very limited resources: no IRQ, no DMA, only a
single native chip-select and Tx/Rx FIFO with just 8 words depth
available. In order to provide a transparent initial boot code execution
the Boot SPI controller is also utilized by an vendor-specific IP-block,
which exposes an SPI flash direct mapping interface. Since both direct
mapping and SPI controller normal utilization are mutual exclusive only
one of these interfaces can be used to access an external SPI slave
device. That's why a dedicated mux is embedded into the System Boot
Controller. All of that is taken into account in the Baikal-T1-specific DW
APB SSI glue driver implemented by means of the DW SPI core module.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-22-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
A functionality of the poll-based transfer has been removed by
commit 1ceb09717e98 ("spi: dw: remove cs_control and poll_mode members
from chip_data") with a justification that "there is no user of one
anymore". It turns out one of our DW APB SSI core is synthesized with no
IRQ line attached and the only possible way of using it is to implement a
poll-based SPI transfer procedure. So we have to get the removed
functionality back, but with some alterations described below.
First of all the poll-based transfer is activated only if the DW SPI
controller doesn't have an IRQ line attached and the Linux IRQ number is
initialized with the IRQ_NOTCONNECTED value. Secondly the transfer
procedure is now executed with a delay performed between writer and reader
methods. The delay value is calculated based on the number of data words
expected to be received on the current iteration. Finally the errors
status is checked on each iteration.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In some circumstances the current implementation of the SPI memory
operations may occasionally fail even though they are executed in the
atomic context. This may happen if the system bus is relatively slow in
comparison to the SPI bus frequency, or there is a concurrent access to
it, which makes the MMIO-operations occasionally stalling before
push-pulling data from the DW APB SPI FIFOs. These two problems we've
discovered on the Baikal-T1 SoC. In order to fix them we have no choice
but to set an artificial limitation on the SPI bus speed.
Note currently this limitation will be only applicable for the memory
operations, since the standard SPI core interface is implemented with an
assumption that there is no problem with the automatic CS toggling.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside from the synchronous Tx-Rx mode, which has been utilized to create
the normal SPI transfers in the framework of the DW SSI driver, DW SPI
controller supports Tx-only and EEPROM-read modes. The former one just
enables the controller to transmit all the data from the Tx FIFO ignoring
anything retrieved from the MISO lane. The later mode is so called
write-then-read operation: DW SPI controller first pushes out all the data
from the Tx FIFO, after that it'll automatically receive as much data as
has been specified by means of the CTRLR1 register. Both of those modes
can be used to implement the memory operations supported by the SPI-memory
subsystem.
The memory operation implementation is pretty much straightforward, except
a few peculiarities we have had to take into account to make things
working. Since DW SPI controller doesn't provide a way to directly set and
clear the native CS lane level, but instead automatically de-asserts it
when a transfer going on, we have to make sure the Tx FIFO isn't empty
during entire Tx procedure. In addition we also need to read data from the
Rx FIFO as fast as possible to prevent it' overflow with automatically
fetched incoming traffic. The denoted peculiarities get to cause even more
problems if DW SSI controller is equipped with relatively small FIFO and
is connected to a relatively slow system bus (APB) (with respect to the
SPI bus speed). In order to workaround the problems for as much as it's
possible, the memory operation execution procedure collects all the Tx
data into a single buffer and disables the local IRQs to speed the
write-then-optionally-read method up.
Note the provided memory operations are utilized by default only if
a glue driver hasn't provided a custom version of ones and this is not
a DW APB SSI controller with fixed automatic CS toggle functionality.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The DW SSI errors handling method can be generically implemented for all
types of the transfers: IRQ, DMA and poll-based ones. It will be a
function which checks the overflow/underflow error flags and resets the
controller if any of them is set. In the framework of this commit we make
use of the new method to detect the errors in the IRQ- and DMA-based SPI
transfer execution procedures.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The parameter will be needed for another wait-done method being added in
the framework of the SPI memory operation modification in a further
commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
By design of the currently available native set_cs callback, the CS
de-assertion will be done only if it's required by the corresponding
controller capability. But in order to pre-fill the Tx FIFO buffer with
data during the SPI memory ops execution the SER register needs to be left
cleared before that. We'll also need a way to explicitly set and clear the
corresponding CS bit at a certain moment of the operation. Let's alter
the set_cs function then to also de-activate the CS, when it's required.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI memory operations implementation will require to have the CS register
cleared before executing the operation in order not to have the
transmission automatically started prior the Tx FIFO is pre-initialized.
Let's clear the register then on explicit controller reset to fulfil the
requirements in case of an error or having the CS left set by a bootloader
or another software.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It's pointless to enable the chip back if the DMA setup procedure fails,
since we'll disable it on the next transfer anyway. For the same reason We
don't do that in case of a failure detected in any other methods called
from the transfer_one() method.
While at it consider any non-zero value returned from the dma_setup
callback to be erroneous as it's supposed to be in the kernel.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It's theoretically erroneous to enable IRQ before the chip is turned on.
If IRQ handler gets executed before the chip is enabled, then any data
written to the Tx FIFO will be just ignored.
I say "theoretically" because we haven't noticed any problem with that,
but let's fix it anyway just in case...
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to make the transfer_one() callback method more readable and
for unification with the DMA-based transfer, let's detach the IRQ setup
procedure into a dedicated function. While at it rename the IRQ-based
transfer handler function to be dw_spi-prefixe and looking more like the
DMA-related one.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Current IRQ-based SPI transfer execution procedure doesn't work well at
the final stage of the execution. If all the Tx data is sent out (written
to the Tx FIFO) but there is some data left to receive, the Tx FIFO Empty
IRQ will constantly happen until all of the requested inbound data is
received. Though for a short period of time, but it will make the system
less responsive. In order to fix that let's refactor the SPI transfer
execution procedure by taking the Rx FIFO Full IRQ into account. We'll read
and write SPI transfer data each time the IRQ happens as before. If all
the outbound data is sent out, we'll disable the Tx FIFO Empty IRQ. If
there is still some data to receive, we'll adjust the Rx FIFO Threshold
level, so the next IRQ would be raised at the moment of all incoming data
being available in the Rx FIFO.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The Tx and Rx data write/read procedure can be significantly simplified by
using Tx/Rx transfer lengths instead of the end pointers. By having the
Tx/Rx data leftover lengths (in the number of transfer words) we can get
rid of all subtraction and division operations utilized here and there in
the tx_max(), rx_max(), dw_writer() and dw_reader() methods. Such
modification will not only give us the more optimized IO procedures, but
will make the data IO methods much more readable than before.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB SSI controller can be used by the two SPI core interfaces:
traditional SPI transfers and SPI memory operations. The controller needs
to be accordingly configured at runtime when the corresponding operations
are executed. In order to do that for the both interfaces from a single
function we introduce a new data wrapper for the transfer mode, data
width, number of data frames (for the automatic data transfer) and the bus
frequency. It will be used by the update_config() method to tune the DW
APB SSI up.
The update_config() method is made exported to be used not only by the DW
SPI core driver, but by the glue layer drivers too. This will be required
in a coming further commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Rx sample delay can be SPI device specific, and should be synchronously
initialized with the rest of the communication and peripheral device
related controller setups. So let's move the Rx-sample delay setup into
the DW APB SSI configuration update method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The code currently responsible for the SPI communication speed setting up
is a bit messy. Most likely for some historical reason the bus frequency
is saved in the peripheral chip private data. It's pointless now since the
custom communication speed is a SPI-transfer-specific thing and only if
there is no SPI transfer data specified (like during the SPI memory
operations) it can be taken from the SPI device structure. But even in the
later case there is no point in having the clock divider and the SPI bus
frequency saved in the chip data, because the controller can be used for
both SPI-transfer-based and SPI-transfer-less communications. From
software point of view keeping the current clock divider in an SPI-device
specific storage may give a small performance gain (to avoid sometimes a
round-up division), but in comparison to the total SPI transfer time it
just doesn't worth saving a few CPU cycles in comparison to the total SPI
transfer time while having the harder to read code. The only optimization,
which could worth preserving in the code is to avoid unnecessary DW SPI
controller registers update if it's possible. So to speak let's simplify
the SPI communication speed update procedure by removing the clock-related
fields from the peripheral chip data and update the DW SPI clock divider
only if it's really changed. The later change is reached by keeping the
effective SPI bus speed in the internal DW SPI private data.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI bus speed update functionality will be useful in another parts of
the driver too (like to implement the SPI memory operations and from the
DW SPI glue layers). Let's move it to the update_cr0() method then and
since the later is now updating not only the CTRLR0 register alter its
prototype to have a generic function name not related to CR0.
Leave the too long line with the chip->clk_div setting as is for now,
since it's going to be changed later anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Indeed there is no point in detecting the SPI peripheral device parameters
and initializing the CR0 register fields each time an SPI transfer is
executed. Instead let's define a dedicated CR0 chip-data member, which
will be initialized in accordance with the SPI device settings at the
moment of setting it up.
By doing so we'll finally make the SPI device chip_data serving as it's
supposed to - to preserve the SPI device specific DW SPI configuration.
See spi-fsl-dspi.c, spi-pl022.c, spi-pxa2xx.c drivers for example of the
way the chip data is utilized.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DWC SSI core is supported by means of setting up the
core-specific update_cr0() callback. It isn't suitable for multiple
reasons. First of all having exported several methods doing the same thing
but for different chips makes the code harder to maintain. Secondly the
spi-dw-core driver exports the methods, then the spi-dw-mmio driver sets
the private data callback with one of them so to be called by the core
driver again. That makes the code logic too complicated. Thirdly using
callbacks for just updating the CR0 register is problematic, since in case
if the register needed to be updated from different parts of the code,
we'd have to create another callback (for instance the SPI device-specific
parameters don't need to be calculated each time the SPI transfer is
submitted, so it's better to pre-calculate the CR0 data at the SPI-device
setup stage).
So keeping all the above in mind let's discard the update_cr0() callbacks,
define a generic and static dw_spi_update_cr0() method and create the
DW_SPI_CAP_DWC_SSI capability, which when enabled would activate the
alternative CR0 register layout.
While at it add the comments to the code path of the normal DW APB SSI
controller setup to make the dw_spi_update_cr0() method looking coherent.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the dw_spi_add_host() method a bit by replacing the currently
implemented default set_cs callback setting up and later having it
overwritten by a custom function with direct if-else-based callback
assignment.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds dev_pm_ops to mtk-nor to support suspend/resume,
auto suspend delay is set to -1 by default.
Accessing registers are only permitted after its clock is enabled
to deal with unknown state of operating clk at probe time.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20201006155010.v5.4.I68983b582d949a91866163bab588ff3c2a0d0275@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If the SPI controller has has_dmamode = true and spi_bitbang_start() fails
in spi_imx_probe(), then the driver must release the DMA channels acquired
in spi_imx_sdma_init() by calling spi_imx_sdma_exit() in the fail path.
Fixes: f62caccd12 ("spi: spi-imx: add DMA support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Robin Gong <b38343@freescale.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20201005132229.513119-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
s3c64xx_spi_hwinit() disables interrupts. In s3c64xx_spi_probe() after
calling s3c64xx_spi_hwinit() they are enabled with the following call.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-10-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase timeout by 30 ms for some wiggle room and set the minimum value
to 100 ms. This ensures a non-zero value for short transfers which
may take less than 1 ms. The timeout value does not affect
performance because it is used with a completion.
Similar formula is used in other drivers e.g. sun4i, sun6i.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-9-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure the cur_speed value used in s3c64xx_enable_datapath()
to configure DMA channel and in s3c64xx_wait_for_*() to calculate the
transfer timeout is set to the actual value of (half) the clock speed.
Don't change non-CMU case, because no frequency calculation errors have
been reported.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-8-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove descriptions for non-existent fields and fix indentation.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-7-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename S3C64XX_SPI_SLAVE_* to S3C64XX_SPI_CS_* to match documentation.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201002122243.26849-6-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Report amount of pending data when a transfer stops due to errors.
Report if DMA was used to transfer data and print the status code.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-5-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check return values in prepare_dma() and s3c64xx_spi_config() and
propagate errors upwards.
Fixes: 788437273f ("spi: s3c64xx: move to generic dmaengine API")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-4-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail.
The vendor kernel for ARTIK5 handles CS in a simmilar way.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201002122243.26849-3-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail to complete. This solution to the problem
is found in the vendor kernel for ARTIK5 boards based on Exynos3250.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-2-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
"program" mode on this controller can trigger up to 56 bits of data
shifting. During the operation, data in PRGDATA[0-5] will be
shifted out from MOSI, and data from MISO will be continuously filling
SHREG[0-9].
Currently this mode is used to implement transfer_one_message for 6-byte
full-duplex transfer, but it can execute a transfer for up-to 7 bytes
as long as the last byte is read only.
transfer_one_message is expected to perform full-duplex transfer,
instead of transfer with specific format. mtk_nor_spi_mem_prg is
added here to use this extra byte.
Newer version of this controller can trigger longer data shifting with
shift bytes more than PRGDATA_MAX + SHREG_MAX. This patch is implemented
with that in mind and it checks against both SHREG_MAX and PRG_CNT_MAX
for future support of new controllers.
Patch 3/3 is a fix for:
commit a59b2c7c56 ("spi: spi-mtk-nor: support standard spi properties")
which breaks supports_op logic. But it can't be separated as it depends
on patch 2/3. Fortuantely the broken commit isn't in stable yet.
Chuanhong Guo (3):
spi: spi-mtk-nor: make use of full capability of prg mode
spi: spi-mtk-nor: add helper for checking prg mode ops
spi: spi-mtk-nor: fix op checks in supports_op
drivers/spi/spi-mtk-nor.c | 179 +++++++++++++++++++++++++++++++++-----
1 file changed, 158 insertions(+), 21 deletions(-)
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Mark Brown