Jesse's SOix work required some patches from acpi-next, so pull it in
through a topic barnch.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, the forcewake refcount will be incorrectly set to zero during
system suspend if there is any reference held via the
i915_forcewake_user debugfs entry.
Fix this by simply not zeroing the sw counters during suspend and
restoring the original state using them. Note that the only other
places where we zeroed the counters were driver load and unload time,
where it was redundant anyway.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78059
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This matches the runtime suspend paths and allows the system to enter
the lowest power mode at freeze time.
v2: move disable_pc8 call to thaw_early (Imre)
move enable_pc8 to freeze_late (Imre/Jesse)
v3: drop spurious hunk from _freeze now that we have freeze_late (Jesse)
v4: move back to suspend_late (Imre was right)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This indicates to the firmware that it can power down various other
components or bring them back up, depending on the target system state.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the system to enter the lowest power mode during system freeze.
v2: delete force wake timer at suspend (Imre)
v3: add GT work suspend function (Imre)
v4: use uncore forcewake reset (Daniel)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to make sure everything is disabled and at its lowest power when
freezing.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are just single registers so wasting space for the pipe offsets
seems a bit pointless. So just use the _PIPE3() macro instead.
Also rewrite the _PIPE3() macro to be more obvious, and protect the
arguments properly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW uses IVB cursor offsets.
Whithout this patch it is not possible to use multiple outputs with cursor
on BDW.
The cursor gets completely crazy because update position uses the wrong
cursor register for the second pipe.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79621
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If both KMS is disabled (by i915.modeset=0 or nomodeset parameters) and
UMS is disabled (by CONFIG_DRM_I915_UMS=n, the default), the user might
not be aware his setup is not supported. Inform the users (and, by
extension, the poor i915 developers having to read their dmesgs in bug
reports) why their graphics experience might be lacking.
A similar message was added on the UMS path in
commit e147accbd1
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Oct 10 15:25:37 2013 +0300
drm/i915: tell the user KMS is required for gen6+
but it won't be reached if CONFIG_DRM_I915_UMS=n since
commit b30324adaf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:11:25 2013 +0100
drm/i915: Deprecated UMS support
v2: Use DRM_DEBUG_DRIVER.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we do a full re-init of all interrupts after a gpu hang.
Which is pretty bad since we don't restore the interrupts we've
enabled at runtime correctly. Even with that addressed it's rather
horribly race.
But on g4x and later we only reset the gt and not the entire gpu.
Which means we only need to reset the GT interrupt bits. Which has the
nice benefit that vblank waits, pipe CRC interrupts and everything
else display related just keeps on working.
The downside is that gt interrupt handling (i.e. ring->get/put_irq) is
still racy. But as long as the gpu hang reliably wakes all waters and
we have a short time where the refcount drops to 0 we'll recover. So
not that bad really.
v2: Ville noticed that GTIMR and PMIMR don't get cleared, only the
subordinate per-ring registers. So let's rip out all the interrupt dancing.
The FIXME comment is still required though since the ring irq handling
happens at the per-ring interrupt mask registers, too.
Testcase: igt/kms_flip/vblank-vs-hang
Testcase: igt/kms_pipe_crc_basic/hang-*
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Atm, we disable GT power saving during the end of the suspend sequence
in i915_save_state(). Doing the disabling at that point seems arbitrary.
One reason to disable it early though is to have a quiescent HW state
before we do anything else (for example save registers). So move the
disabling earlier, which also takes care canceling of the deferred RPS
enabling work done by intel_disable_gt_powersave().
Note that after the move we'll call intel_disable_gt_powersave() only
in case modeset is enabled, but that's anyway the only case where we
have it enabled in the first place.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently user space can access GEM buffers mapped to GTT through
existing mappings concurrently while the platform specific suspend
handlers are running. Since these handlers may change the HW state in a
way that would break such accesses, remove the mappings before calling
the handlers. Spotted by Ville.
Also Chris pointed out that the lists that i915_gem_release_all_mmaps()
walks through need dev->struct_mutex, so take this lock. There is a
potential deadlock against a concurrent RPM resume, resolve this by
aborting and rescheduling the suspend (Daniel).
v2:
- take struct_mutex around i915_gem_release_all_mmaps() (Chris, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel keeps on ramping up the warning level of the DRM and our display
core to make it complain whenever the locking rules are not followed.
This caught
commit 24576d2397
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Mar 26 09:25:45 2013 -0700
drm/i915: enable VT switchless resume v3
introducing an unlocked access to the CRTC whilst disabling it for
suspend.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78114
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We really just want to go detect displays again and fire off a hotplug
event if things have changed, not go through full hotplug processing.
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has three pipes so let's expose them all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patch done using the following semantic patch (thanks Daniel for the
help!)
@@
iterator name list_for_each_entry;
iterator name for_each_crtc;
struct drm_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
+for_each_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Update to also fill in the new num_pipes field.
v3: Rebase on top of the pciid extraction.
v4: Switch from info->has*ring to info->ring mask. Also add VEBOX support whiel
at it.
v5: s/CHV_PCI_IDS/CHV_IDS/, and drop the trailing '\'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add runtime PM support for VLV, but leave it disabled. The next patch
enables it.
The suspend/resume sequence used is based on [1] and [2]. In practice we
depend on the GT RC6 mechanism to save the HW context depending on the
render and media power wells. By the time we run the runtime suspend
callback the display side is also off and the HW context for that is
managed by the display power domain framework.
Besides the above there are Gunit registers that depend on a system-wide
power well. This power well goes off once the device enters any of the
S0i[R123] states. To handle this scenario, save/restore these Gunit
registers. Note that this is not the complete register set dictated by
[2], to remove some overhead, registers that are known not to be used are
ignored. Also some registers are fully setup by initialization functions
called during resume, these are not saved either. The list of registers
can be further reduced, see the TODO note in the code.
[1] VLV_gfx_clocking_PM_reset_y12w21d3 / "Driver D3 entry/exit"
[2] VLV2_S0IXRegs
v2:
- unchanged
v3:
- fix s/GEN6_PMIIR/GEN6_PMIMR/ typo when saving/restoring registers
(Ville)
v4:
- rebased on the previous patch fixing GEN register prefixes
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[ rebased (according to v4) ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, none of the RPM callbacks can fail, but the next patch adding
RPM support for VLV changes this, so prepare for it.
In case one of these callbacks return error RPM will get permanently
disabled until the error is explicitly cleared. In the future we could
add support for re-enabling it, for example after resetting the HW, but
for now - hopefully - we can live with the simpler solution.
v2:
- propagate the error from the resume callbacks too (Paulo)
v3:
- fix rebase fail typo around IS_GEN6() check in intel_runtime_suspend()
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've seen latencies up to 15msec, so increase the timeout to 20msec.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by the VLV runtime PM helpers too, so factor it out.
Also add a safety check for the case where the previous force-off is
still pending, since I'm not sure if Punit can handle a new setting
while the previous one hasn't settled yet.
v2:
- unchanged
v3:
- add a note to the commit message about the safety check (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During runtime suspend there can be a last pending rps.work, so make
sure it's canceled. Note that in the runtime suspend callback we can't
get any RPS interrupts since it's called only after the GPU goes idle
and we set the minimum RPS frequency. The next possibility for an RPS
interrupt is only after getting an RPM ref (for example because of a new
GPU command) and calling the RPM resume callback.
v2:
- patch introduced in v2 of the patchset
v3:
- Change the order of canceling the rps.work and disabling interrupts to
avoid the race between interrupt disabling and the the rps.work. Race
spotted by Ville.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init sizzling on all platforms so move it to the
platform independent runtime resume callback. The ring frequency reinit
is also needed everywhere except on VLV, but gen6_update_ring_freq()
will be a noop on VLV, so we can move this function too to platform
independent code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by the next patch moving the call out from platform
specific RPM callbacks to platform independent code.
No functional change.
v2:
- patch introduce in v2 of the patchset
v3:
- simplify platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV we depend on RC6 to save the GT render and media HW context
before going to the D3 state via RPM, so as a preparation for the
VLV RPM support (added in an upcoming patch) disable RPM if RC6 is
disabled.
There is probably a similar dependency on other platforms too, so for
safety require RC6 for those too. For these platforms (SNB, HSW, BDW)
this is then a possible fix.
v2:
- require RC6 for all RPM platforms, not just for VLV (Paulo, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.
v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Getting struct_mutex around the whole intel_enable_gt_powersave()
function is not necessary, since it's only needed for the ILK path
therein.
This will make intel_enable_gt_powersave() useable on the RPM resume
path for >=GEN6 (added in an upcoming patch to reset the RPS state
during RPM resume), where we can't (and need not) get this mutex.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.
V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.
As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dev->struct_mutex locking in drm_irq.c only protects
dev->irq_enabled. Which isn't really much at all and only prevents
especially nasty ums userspace from concurrently installing the
interrupt handling a few times. Or at least trying.
There are tons of unlocked readers of dev->irqs_enabled in the vblank
wait code (and by extension also in the pageflip code since that uses
the same vblank timestamp engine).
Real modesetting drivers should ensure that nothing can go haywire
with a sane setup teardown sequence. So we only really need this for
the drm_control ioctl, everywhere else this will just paper over
nastiness.
Note that drm/i915 is a bit specially due to the gem+ums combination.
So there we also need to properly protect the entervt and leavevt
ioctls. But it's definitely saner to do everything in one go than to
drop the lock in-between.
Finally there's the gpu reset code in drm/i915. That one's just race
(concurrent userspace calls to for vblank waits of pageflips could
spuriously fail). So wrap it up in with a nice comment since fixing
this is more involved.
v2: Rebase and fix commit message (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During resume the intel hda audio driver depends on the i915 driver
reinitializing the audio power domain. Since the order of calling the
i915 resume handler wrt. that of the audio driver is not guaranteed,
move the power domain reinitialization step to the resume_early
handler. This is guaranteed to run before the resume handler of any
other driver.
The power domain initialization in turn requires us to enable the i915
pci device first, so move that part earlier too.
Accordingly disabling of the i915 pci device should happen after the
audio suspend handler ran. So move the disabling later from the i915
resume handler to the resume_late handler.
v2:
- move intel_uncore_sanitize/early_sanitize earlier too, so they don't
get reordered wrt. intel_power_domains_init_hw()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76152
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable and loud comments that this is just a hack.]
[danvet: Fix "Should it be static?" sparse warning reported by Wu
Fengguang's kbuilder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This sould be enough.
v2: BDW should also run hsw_runtime_resume (Ben).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 is part of runtime PM, the check is useless.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just because I have a SNB machine and I can easily test it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're adding runtime suspend support to more platforms, so organize
the code in a way that all a new platform needs to do is to add its
own gen-specific functions. Also rename the i915_ functions to intel_
to make it clear that it's the top level one, not something that just
runs on i915 platforms.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the rest of the references to drm_i915_private_t. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop hunk in i915_cmd_parser.c]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we removed all the intermediate abstractions, we can rename
these functions to just hsw_{en,dis}able_pc8.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already get runtime PM references, and PC8 is now part of runtime
PM, so this is enough.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.
While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
- We are not aware of anybody wanting a "PC8 without D3" environment.
- If we keep both features as separate, we'll have to to test both
PC8 and PC8+D3 code paths. We're already having a major pain to
make QA do automated testing of just one thing, testing both paths
will cost even more.
- Only Haswell+ supports PC8, so if we want to add runtime PM support
to, for example, IVB, we'll have to copy some code from the PC8
feature to runtime PM, so merging both features as a single thing
will make it easier for enabling runtime PM on other platforms.
This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.
v2: - Rebase.
v3: - Rebase.
- Fully remove the deprecated i915 params since Daniel doesn't
consider them as part of the ABI.
v4: - Rebase.
- Fix typo in the commit message.
v5: - Rebase, again.
- Add a huge comment explaining the different forcewake usage
(Chris, Daniel).
- Use open-coded forcewake functions (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we regularly defer the forcewake dance to a timer func, it is
likely to fire after we disable the device during suspend. This
generates an oops as we detect inconsistency in the hardware state. So
before suspend, we want to complete the outstanding dance and generally
sanitize the registers before handing back to the BIOS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW is no longer flagged as preliminary hw, but without
i915.preliminary_hw_support module param set the logs are filled with
WARNs about it.
Just make semaphores off the BDW per-chip default for now.
CC: Ben Widawsky <ben@bwidawsk.net>
Reported-by: Sebastien Dufour <sebastien.dufour@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter