This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some late fixes for dwc3 so we have something more stable
on v3.17-final.
Most bugs have been there for quite a while and nobody
noticed, except for TRB completion when multiple TRBs
are started.
Patches were tested on AM437x SK and J6 EVM and are passing
my tests.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CdSO
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.17-rc4
Some late fixes for dwc3 so we have something more stable
on v3.17-final.
Most bugs have been there for quite a while and nobody
noticed, except for TRB completion when multiple TRBs
are started.
Patches were tested on AM437x SK and J6 EVM and are passing
my tests.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci driver will OOPS on resume from S2/S3 if dma_alloc_coherent()
is out of memory. This is a result of two things:
1. xhci_mem_cleanup() in xhci-mem.c free's xhci->lpm_command if
it's not NULL, but doesn't set it to NULL after the free.
2. xhci_mem_cleanup() is called twice on resume, once for normal
restart and once from xhci_mem_init() if dma_alloc_coherent() fails,
resulting in a free of xhci->lpm_command that has already been freed.
The fix is to set xhci->lpm_command to NULL after freeing it.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().
Reported-by: Manuel Reimer <manuel.reimer@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.
On connecting the cable a message like this appears four times in the log:
reset full speed USB device number 4 using uhci_hcd
That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize USB PHY after every Link controller reset
Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY drivers keep track of the current state of the hardware,
so don't change PHY settings under it.
Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a large numbers of issues with ASM1051 devices in uas mode:
1) They do not support REPORT SUPPORTED OPERATION CODES
2) They use out of spec 8 byte status iu-s when they have no sense data,
switching to normal 16 byte status iu-s when they do have sense data.
3) They hang / crash when combined with some disks, e.g. a Crucial M500 ssd.
4) They hang / crash when stressed (through e.g. sg_reset --bus) with disks
with which then normally do work (once 1 & 2 are worked around).
Where as in BOT mode they appear to work fine, so the best way forward with
these devices is to just blacklist them for uas usage.
Unfortunately this is easier said then done. as older versions of the ASM1053
(which works fine) use the same usb-id as the ASM1051.
When connected over USB-3 the 2 can be told apart by the number of streams
they support. So this patch adds some less then pretty code to disable uas for
the ASM1051. When connected over USB-2, simply disable uas alltogether for
devices with the shared usb-id.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 2ec2a8be (usb: dwc3: gadget:
always enable IOC on bulk/interrupt transfers)
we created a situation where it was possible to
hang a bulk/interrupt endpoint if we had more
than one pending request in our queue and they
were both started with a single Start Transfer
command.
The problems triggers because we had not enabled
Transfer In Progress event for those endpoints
and we were not able to process early giveback
of requests completed without LST bit set.
Fix the problem by finally enabling Xfer In Progress
event for all endpoint types, except control.
Fixes: 2ec2a8be (usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DMrz
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.17-rc4
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Cc: <stable@vger.kernel.org> # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
dep->endpoint.desc is checked at the beginning of
dwc3_gadget_ep_queue(), but after that it may be set to NULL
by another thread and then accessed again in dwc3_gadget_ep_queue().
This will lead to kernel oops.
Expand spinlock protection area to aviod race condition.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Fixes: 81d5dfe6d8 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Up to now, when endpoint addresses in descriptors were non-consecutive,
there were created redundant files, which could cause problems in kernel,
when user tried to read/write to them. It was result of fact that maximum
endpoint address was taken as total number of endpoints in function.
This patch adds endpoint descriptors counting and storing their addresses
in eps_addrmap to verify their cohesion in each speed.
Endpoint address map would be also useful for further features, just like
vitual endpoint address mapping.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch protects the mod->irq_bempsts and mod->irq_brdysts by
spin lock in the usbhs_status_get_each_irq() because other functions
will write them during spin lock. Otherwise, the driver will clears
the BRDYSTS and/or BEMPSTS wrongly, and then, the transaction will not
finish.
Also since the driver should use the INTSTS0 and BRDYSTS and BEMPSTS
as the same timing, the patch protects them.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>] lr : [<c0278fb4>] psr: 60000193
sp : c0513ce8 ip : c0513c58 fp : c0513d24
r10: 00000001 r9 : 00000193 r8 : eebec4a0
r7 : eebec410 r6 : eebe0c6c r5 : 00000000 r4 : ee4a2774
r3 : 00000000 r2 : ee251e00 r1 : c0513cf4 r0 : ee4a2774
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Clearly this was meant to be an include guard, but a trailing
underscore was missing. It has been this way since the file was
introduced in 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver").
Fixes: 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.
The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.
Validated using the following usbtest write case in MUSB host mode.
# testusb -t1 -c1
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.
Cc: <stable@vger.kernel.org>
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.
It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist. This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for NOVITUS Bono E thermal printer.
Reported-by: Emanuel Koczwara <poczta@emanuelkoczwara.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
commit bdd405d2a5 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled. Fix that by doing a simple #ifdef guard around it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Michael Welling <mwelling@emacinc.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a bit bigger hammer then I would like to use for this, but for now
it will have to make do. I'm working on getting my hands on one of these so
that I can try to get streams to work (with a quirk flag if necessary) and
then we can re-enable them.
For now this at least makes uas capable disk enclosures work again by forcing
fallback to the usb-storage driver.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the number of ports requested by subdriver to avoid
writing beyond the end of fixed-size array in interface data.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of ports requested by a
subdriver (which could have been determined from device descriptors) did
not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the maximum number of endpoints per type to avoid
writing beyond the end of a stack-allocated array.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of endpoints of a certain
type reported by a device did not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we want to keep support for both older usb-phys as well as the
newer generic phys, lets first get the generic PHYs and fallback to
older USB-PHYs only when we fail to get the former.
This should fix the issue with ehci-exynos and ohci-exynos, wherein
in the absence of SAMSUNG_USB2PHY config symbol, we end up getting
the NOP_USB_XCEIV phy when the same is enabled. And thus the PHYs
are not configured properly.
Reported-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jingoo Han <jg1.han@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.
commit 596d789a21 introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.
Fixes: 596d789a21 "USB: set hub's default autosuspend delay as 0"
Cc: [3.8+] <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michael Welling <mwelling@emacinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark