Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.
Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.
Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change vsi->num_queue_pairs to equal the number that are configured
by the VF. This, in turn, limits the number of queues that are
enable/disabled. This fixes the mismatched case for when a VF configures
fewer queues than is allocated to it by the PF.
Change other sections to use alloc_queue_pairs as warranted.
Change-ID: I0de1b55c9084e7be6acc818da8569f12128a82c2
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the l2tsel bit on Rx queue contexts that are assigned to VFs so
that the VF can get the stripped VLAN tag.
Change-ID: I7d9bc56238a9ea9baf5e8a97e69b9e27ebb9d169
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.
Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up. AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.
Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.
Also fix it to send the correct seid to aq for multicast promiscuous set.
Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes comment for reset reason
Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.
Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TPH is not currently enabled in this product, make sure it
isn't enabled by default.
Change-ID: Ibb1a10799c33c4c76dec06fcd53b1d6efa13c1f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the host VMM administrator has changed the VF device's MAC address then
the i40e driver needs to halt the VF device so that the administrator will
be forced to reload the VF driver. This will cause the VF driver to start
using the newly assigned MAC address. This brings the i40e driver into
conformance with operational characteristics of other Intel SR-IOV
featured drivers.
Change-ID: Ic7242cceb8287dd2cb72fb1f3166a032a28bf88a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.
Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete all the old and stale MAC filters for the VF VSI when the host
administrator changes the VF MAC address from under its feet. Also don't
bother to add a filter for the VSI when its going to go away anyway.
Just record the new address and punch the VF reset.
Change-ID: Ic0d12055926f41989d1965ccf500053729c063ad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware supports VF antispoofing for both MAC addresses and VLANs.
Enable this feature by default for all VFs and implement the netdev op
to control it from the command line.
Change-ID: Ifb941da22785848aa3aba6b2231be135b8ea8f31
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for the VF to achieve its programmed Tx rate, we need to set
the max credits value to 4. While we're at it, get rid of some magic
numbers.
Change-ID: I4f17b4d3a90f1e069bdd134a543f0aa22feac3a9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because the hardware configures VF Tx rates in increments of 50 Mbps,
values smaller than that would be rounded down to 0, which was
interpreted as no limit at all. Rather than do this, we round up to 50
Mbps and notify the user.
Change-ID: I5275848233fe7514cf93e11323661c68f4c38737
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As recommended by the hardware guys, enable descriptor prefetch for
rings belonging to VFs. This matches a change already made for ring
belonging to the PF.
Change-ID: Idcc4dc7064bc9144ea81f5701ad07b7ecd11ba49
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are assigned to active VMs and we disable SR-IOV out from under them,
bad things happen. Currently, the VM does not crash, but the VFs lose all
resources and have no way to get them back.
Add an additional check for when the user is disabling through sysfs, and add a
comment to clarify why we check twice.
Change-ID: Icad78eef516e4e1e4a87874d59132bc3baa058d4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function to set the VF MAC address was not taking the port VLAN
filter into account when setting/clearing/resetting the VF's host
administered MAC address. Be sure to use the port VLAN for VF MAC
filtering configurations.
Change-ID: I12595331981c79529738f041dcdbdb667ef8f5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were already taking care to retain the MAC filter list when deleting a
port VLAN. Take some additional care to retain the MAC filter list when
changing a port VLAN.
Change-ID: Iacf9599ea24ecb4dca8e419aacaf4b58ca361a9c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although the driver would correctly allow the VF link state to be
controlled by 'ip set link', it would not report it correctly back.
Fix this by filling out the appropriate field in the vf info struct.
Change-ID: I58d8e356438190e1ee9660b424301af6f416cdbe
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the net device op for Tx bandwidth setting. Setting the Tx
bandwidth is done by 'ip link set <PF device> vf <VF num> rate <Tx
rate>', with the rate specified in Mbit/sec. The rate setting is
displayed with 'ip link show'.
Change-ID: I4d45dda8320632fdb6ec92c87d083e51070b46ab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a host VMM administrator hoses his VF by assigning a port VLAN after
it is already up and running with implicit permission to set local
VLANs then we print a message warning the host administrator that the
VF driver needs to be reloaded.
In addition we need to knock the VF offline so that it does not continue
to receive traffic not on the port VLAN assigned to it. So we reset the
VF. The VF will cease operation and the administrator will be forced to
unload and reload the VF driver to make it work again.
Change-ID: Iae1ae006b244e74e30a4ee546b3c5fca5cfb40aa
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If "vf_id" is smaller than hw->func_caps.vf_base_id then it leads to
an array underflow of the pf->vf[] array. This is unlikely to happen
unless the hardware is bad, but it's a small change and it silences a
static checker warning.
Fixes: 7efa84b7ab ('i40e: support VFs on PFs other than 0')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.
Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.
Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the 2.4 firmware reports the correct number of MSI-X vectors,
use this value correctly when communicating with the VF, and when
setting up the interrupt linked list.
The PF has always reported the correct number of MSI-X vectors, so we
should never increment the value in the vf driver.
Change-ID: Ifeefc631c321390192219ce2af9ada6180c1492f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent the possibility of overflow due multiplication of number and size
use kcalloc instead of kzalloc.
Change-ID: Ibe4d81ed7d9738d3bbe66ee4844ff9be817e8080
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ain't nothing gonna break my stride, nobody's gonna slow me down,
oh no. I got to keep on moving.
This was originally put in for debugging just-in-case purposes
and never removed.
Change-ID: Ic12c2e179c3923f54e6ba0a9e4ab05d25c3bab29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DOWN flag before attempting to disable VFs when unloading the
driver. Also, don't attempt to reset the VFs when the driver is
unloading, because the switch configuration will fail. This fixes a
panic on unload when VFs are enabled.
Change-ID: I25a6567e89c9687145f510ff4f630932412c5c5d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are present when the driver loads, then set up some resources
so they can function.
Change-ID: I485916a811609a9990ce663d06dc645f625b07ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the VF can never communicate with the PF after a VF
reset.
Change-ID: I8d10f1d0d0638d50d39f0aff263422e05d83ad83
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks like a cut and paste error. The code makes no sense where
it is, and accomplishes nothing. Since we've removed the goto, we can
also get rid of the extraneous brackets.
Change-ID: I9315e3eafeee0a5713c94b0dc57b58b60a849124
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e Physical Function (PF) driver will allow the
Virtual Function (VF) driver to configure its own VLAN filters if no port
VLAN filter has been configured. This leads to the possibility of the
administrator setting a port VLAN filter for the VF after the VF has already
configured its own VLAN filters. This leads to a conflict that can only be
resolved by reloading the VF driver. When the conflicting administrative
command is detected in setting the port VLAN then log a message indicating to
the system administrator that he must now reload the VF driver for the new
port VLAN settings to take effect.
Change-Id: I8de73b885d944a043aff32226297e4249862bcad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this message mean something, rather than just spitting out a VSI id
without any context whatsoever.
Change-ID: Iafb906c6db46d4b5dcbe84adc9ed44730d08bd42
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This write done at the end of VF reset and should not be performed here.
Change-ID: I4d89813b68c6173184293868a6f26cf559bc2405
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you use ip to change the MAC address of a VF while the VF
driver is loaded, closing the VF interface or unloading the VF
driver will cause the VF driver to remove the MAC filter for its
original (now invalid) MAC address. This would cause the PF
driver to kick an error message to the log, and back to the VF
driver.
Since the VF driver has not really done anything naughty, let's
not punish it. Don't check for MAC address overrides on the
delete operation, just make sure it's a valid address. This keeps
us from spamming the log with confusing errors.
Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some badly formatted lines, long lines and a mis-formatted else.
Change-ID: Iac2eef064ae27c55a0c3d9c15c525bf8fed8ab6f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF VSI was never updated to enable or disable internal switch loopback
when VFs were created or destroyed via the sysfs interface. Add some
helper functions to take care of that.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF is allowed to request the PF to set its already assigned
MAC address without generating an error.
Change-Id: I8dfdf353396995dbbb26cafab4e42b451911da3d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Broadcast promiscuous should only be turned on when general
promiscuous mode is turned on, otherwise VLAN tagged packets out of
the assigned VLAN domain are received.
Add a broadcast MAC filter in order to continue to receive
broadcast traffic on VLANs, MAIN or VMDQ VSI.
Change-Id: I99d8e382a082ee51201228f1226af3b46452ac55
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a problem where the 'ip link show' command would display stale
link address information after the link address was set via the 'ip
link set' command. In addition, fix problem with the user being
allowed to overwrite the administratively set VF MAC address.
Change-Id: I669ed14e55f2b633ef7b456b713632b08468671c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When communicating with VF devices over the AQ, the FW refers to the
VF by its global VF ID, not local the VF ID with reference to its
parent PF. Since the global and local VF IDs are identical for PF 0,
the code worked correctly on PF 0.
However, we cannot just use global IDs throughout the code as most of
the other references to the VF (VSI setup, register offsets, etc.)
require the local VF ID. Instead, we just add or subtract our base VF
ID when sending and receiving AQ messages.
Change-Id: I92f4332b4876bc68b2f9af9ebf48761f63b6bd97
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When SR-IOV is disabled, the (now nonexistent) virtual function
devices undergo a VFLR event. We don't need to handle this event
because the VFs are gone, but we do need to tell the HW that they are
complete. This fixes an issue with a phantom VFLR and broken VFs when
SR-IOV is re-enabled.
Change-Id: I7580b49ded0158172a85b14661ec212af77000c8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use struct assignment rather than an expensive memory copy.
Change-Id: I1d18d510774dfd41a9c1250cdef238a4187528f5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Serey Kong