Add a new NL80211_CMD_SET_TX_BITRATE_MASK command and related
attributes to provide support for setting TX rate mask for rate
control. This uses the existing cfg80211 set_bitrate_mask operation
that was previously used only with WEXT compat code (SIOCSIWRATE). The
nl80211 command allows more generic configuration of allowed rates as
a mask instead of fixed/max rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).
The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.
The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, cfg80211 had reported "0" for MCS (i.e. 802.11n) bitrates
through the wireless extensions interface. However, nl80211 was
converting MCS rates into a reasonable bitrate number. This patch moves
the nl80211 code to cfg80211 where it is now shared between both the
nl80211 interface and the wireless extensions interface.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an interface to set, delete and flush PMKIDs through nl80211.
Main users would be fullmac devices which firmwares are capable of
generating the RSN IEs for the re-association requests, e.g. iwmc3200wifi.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
* transmitter, which must be equal to the sender (origin)
* receiver (on the wireless medium), which is the AP in
the case of managed mode
* the recipient (destination), which is on the APs local
network segment
In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.
To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.
Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the NL80211_CMD_GET_SURVEY command and an get_survey()
ops that a driver can implement. The goal of this command is to allow a
drivers to report channel survey data (e.g. channel noise, channel
occupation).
For now, only the mechanism to report back channel noise has been
implemented.
In future, there will either be a survey-trigger command --- or the existing
scan-trigger command will be enhanced. This will allow user-space to
request survey for arbitrary channels.
Note: any driver that cannot report channel noise should not report
any value at all, e.g. made-up -92 dBm.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... which get's rid of three indentical cut-n-paste sections.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resulting object files have the same MD5 as before.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently it is possible to request a scan on only
disabled channels, which could be problematic for
some drivers. Reject such scans, and also ignore
disabled channels that are given. This resuls in
the scan begin/end event only including channels
that are actually used.
This makes the mac80211 check for disabled channels
superfluous. At the same time, remove the no-IBSS
check from mac80211 -- nothing says that we should
not find any networks on channels that cannot be
used for an IBSS, even when operating in IBSS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error unwinding code in set_netns has a bug
that will make it run into a BUG_ON if passed a
bad wiphy index, fix by not trying to unlock a
wiphy that doesn't exist.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linux keeps scan results up to 15 seconds. This can be a problem for fast
moving clients: they get back stale data. But if the kernel reports the age
of the BSS items, then user-space can simply weed out old entries by itself.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jump to out_err when the iftype is not supported.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the interface type changes while connected, and the
driver does not require the interface to be down for a
type change, it is currently possible to get very strange
results unless the driver takes special care, which it
shouldn't have to.
To fix this, take care to disconnect/leave IBSS when
changing the interface type -- even if the driver may fail
the call. Also process all events that may be pending to
avoid running into a situation where an event is reported
but only processed after the type has already changed,
which would lead to missing events and warnings.
A side effect of this is that you will have disconnected
or left the IBSS even if the mode change ultimately fails,
but since the intention was to change it and thus leave or
disconnect, this is not a problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: validate channel settings across interfaces"
contained a locking bug -- in the managed-mode SIWFREQ
call it would end up running into a lock recursion.
This fixes it by not checking that particular interface
for a channel that it needs to stay on, which is as it
should be as that's the interface we're setting the
channel for.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The memory layout for scan requests was rather wrong,
we put the scan SSIDs before the channels which could
lead to the channel pointers being unaligned in memory.
It turns out that using a pointer to the channel array
isn't necessary anyway since we can embed a zero-length
array into the struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for userspace to be able to figure out whether
it obtained a consistent snapshot of data or not when
using netlink dumps, we need to have a generation number
in each dump message that indicates whether the list has
changed or not -- its value is arbitrary.
This patch adds such a number to all dumps, this needs
some mac80211 involvement to keep track of a generation
number to start with when adding/removing mesh paths or
stations.
The wiphy and netdev lists can be fully handled within
cfg80211, of course, but generation numbers need to be
stored there as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, there's a problem that affects regulatory
enforcement and connection stability, in that it is
possible to switch the channel while connected to a
network or joined to an IBSS.
The problem comes from the fact that we only validate
the channel against the current interface's type, not
against any other interface. Thus, you have any type
of interface up, additionally bring up a monitor mode
interface and switch the channel on the monitor. This
will obviously also switch the channel on the other
interface.
The problem now is that if you do that while sending
beacons for IBSS mode, you can switch to a disabled
channel or a channel that doesn't allow beaconing.
Combined with a managed mode interface connected to
an AP instead of an IBSS interface, you can easily
break the connection that way.
To fix this, this patch validates any channel change
with all available interfaces, and disallows such
changes on secondary interfaces if another interface
is connected to an AP or joined to an IBSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now we implemented iwfreq for managed mode, we
needed to keep the implementations separate, but now
that we have all versions implemented we can combine
them and export just one handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni and Maxim reported an oops when using wpa_supplicant -Dnl80211,
which seems to be due to random data being contained in the crypto
settings for the assoc() command. This seems to be due to the missing
memset here, so add it -- it's certainly missing but I'm not 100%
certain that it will fix the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reported this lockdep complaint, that he had also
reported earlier but when trying to analyse I had been
locking at the wrong code, and never saw the problem:
(slightly abridged)
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #6
-------------------------------------------------------
wpa_supplicant/3799 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff81400ff2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffff81400ff2>] rtnl_lock+0x12/0x20
[<ffffffffa009f6a5>] nl80211_send_reg_change_event+0x1f5/0x2a0 [cfg80211]
[<ffffffffa009529e>] set_regdom+0x28e/0x4c0 [cfg80211]
-> #0 (cfg80211_mutex){+.+.+.}:
[<ffffffff8108587b>] __lock_acquire+0xe3b/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
[<ffffffffa009813f>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<ffffffffa009b12b>] nl80211_set_interface+0x3b/0x260 [cfg80211]
When looking at the correct code, the problem is quite
obvious. I'm not entirely sure which code paths lead
here, so until I can analyse it better let's just use
RCU to avoid the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connected to a BSS, or joined to an IBSS, we'll want
to know in userspace without using wireless extensions, so
report the BSS status in the BSS list. Userspace can query
the BSS list, display all the information and retrieve the
station information as well.
For example (from hwsim):
$ iw dev wlan1 scan dump
BSS 02:00:00:00:00:00 (on wlan1) -- associated
freq: 2462
beacon interval: 100
capability: ESS ShortSlotTime (0x0401)
signal: -50.00 dBm
SSID: j
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Paramater set: channel 11
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will soon want to nest key attributes into
some new attribute for configuring static WEP
keys at connect() and ibss_join() time, so we
need nested attributes for that. However, key
attributes right now are 'global'. This patch
thus introduces new nested attributes for the
key settings and functions for parsing them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two small bugs:
1) the connect variable is already initialised, and the
assignment to auth_type overwrites the previous setting
with a wrong value
2) when all authentication attempts fail, we need to report
that we couldn't connect
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Potential memory leak via msg pointer in nl80211_get_key() function.
Signed-off-by: Niko Jokinen <ext-niko.k.jokinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes generic netlink network namespace aware. No
generic netlink families except for the controller family
are made namespace aware, they need to be checked one by
one and then set the family->netnsok member to true.
A new function genlmsg_multicast_netns() is introduced to
allow sending a multicast message in a given namespace,
for example when it applies to an object that lives in
that namespace, a new function genlmsg_multicast_allns()
to send a message to all network namespaces (for objects
that do not have an associated netns).
The function genlmsg_multicast() is changed to multicast
the message in just init_net, which is currently correct
for all generic netlink families since they only work in
init_net right now. Some will later want to work in all
net namespaces because they do not care about the netns
at all -- those will have to be converted to use one of
the new functions genlmsg_multicast_allns() or
genlmsg_multicast_netns() whenever they are made netns
aware in some way.
After this patch families can easily decide whether or
not they should be available in all net namespaces. Many
genl families us it for objects not related to networking
and should therefore be available in all namespaces, but
that will have to be done on a per family basis.
Note that this doesn't touch on the checkpoint/restart
problem where network namespaces could be used, genl
families and multicast groups are numbered globally and
I see no easy way of changing that, especially since it
must be possible to multicast to all network namespaces
for those families that do not care about netns.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've named the registered devices 'drv' sometimes,
thinking of "driver", which is not what it is, it's
the internal representation of a wiphy, i.e. a
device. Let's clean up the naming once and and use
'rdev' aka 'registered device' everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a lot of locking issues have crept into
the smarts of cfg80211, so e.g. scan completion can
race against a new scan, IBSS join can race against
leaving an IBSS, etc.
Introduce a new per-interface lock that protects
most of the per-interface data that we need to keep
track of, and sprinkle assertions about that lock
everywhere. Some things now need to be offloaded to
work structs so that we don't require being able to
sleep in functions the drivers call. The exception
to that are the MLME callbacks (rx_auth etc.) that
currently only mac80211 calls because it was easier
to do that there instead of in cfg80211, and future
drivers implementing those calls will, if they ever
exist, probably need to use a similar scheme like
mac80211 anyway...
In order to be able to handle _deauth and _disassoc
properly, introduce a cookie passed to it that will
determine locking requirements.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse warns about a number of things, and one of them
(use_mfp shadowed variable) actually is a bug, fix all
of them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we call that cfg80211_put_dev(), but that is
misleading. With the new convention of using 'rdev' for
registered_device variables, also call that function
cfg80211_unlock_rdev().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we don't really know that well in the kernel,
let's let the SME control whether it wants to use
reassociation or not, by allowing it to give the
previous BSSID in the associate() parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this case, only one cipher makes sense, unlike for
connect() where it may be possible to have the card or
driver select.
No changes to mac80211 due to the way the structs are
laid out -- but the loop in net/mac80211/cfg.c will
degrade to just zero or one passes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to cfg80211 so that drivers (mac80211 right
now) that don't implement connect but rather auth/assoc can
still be used with the nl80211 connect command. This will
also be necessary for the wext compat code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the cfg80211 connect/disconnect API.
The goal here is to run the AUTH and ASSOC steps in one call.
This is needed for some fullmac cards that run both steps
directly from the target, after the host driver sends a
connect command.
Additionally, all the new crypto parameters for connect()
are now also valid for associate() -- although associate
requires the IEs to be used, the information can be useful
for drivers and should be given.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a new NL80211_CMD_TESTMODE for testing
and calibration use with nl80211. There's no multiplexing
like like iwpriv had, and the command is not available by
default, it needs to be explicitly enabled in Kconfig and
shouldn't be enabled in most kernels.
The command requires a wiphy index or interface index to
identify the device to operate on, and the new TESTDATA
attribute. There also is API for sending replies to the
command, and testmode multicast messages (on a testmode
multicast group).
I've also updated mac80211 to be able to pass through the
command to the driver, since it itself doesn't implement
the testmode command.
Additionally, to give people an idea of how to use the
command, I've added a little code to hwsim that makes use
of the new command to set the powersave mode, this is
currently done via debugfs and should remain there, and
the testmode command only serves as an example of how to
use this best -- with nested netlink attributes in the
TESTDATA attribute. A hwsim testmode tool can be found at
http://git.sipsolutions.net/hwsim.git/. This tool is BSD
licensed so people can easily use it as a basis for their
own internal fabrication and validation tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It isn't very useful to scan the same channel more than once
during a given scan, and some hardware (notably iwlwifi) can
only scan a limited number of channels at a time. To prevent
any overflows, simply disallow scanning any channel multiple
times in a given scan command. This is a small change in the
userspace ABI, but the only user, wpa_supplicant, never asks
for a scan with the same frequency listed twice.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To ease multiple apps working together smoothly,
send a notification when a scan is started.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to unlock cfg80211_mutex in one fail path of
nl80211_set_wiphy.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I disallowed interfering with stations on non-AP interfaces,
I not only forget mesh but also managed interfaces which need
this for the authorized flag. Let's actually validate everything
properly.
This fixes an nl80211 regression introduced by the interfering,
under which wpa_supplicant -Dnl80211 could not properly connect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh Point interfaces can also set parameters, for example plink_open is
used to manually establish peer links from user-space (currently via
iw). Add Mesh Point to the check in nl80211_set_station.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b2a151a288 added a check that prevents adding or deleting
stations on non-AP interfaces. Adding and deleting stations is
supported for Mesh Point interfaces, so add Mesh Point to that check as
well.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
(Reconcile this w/ previous version of patch posted with same
subject... -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan finishes only the program that asked for it
knows what kind of scan it was; let's tell everybody else
about the scan parameters as well so they can evaluate
the result of the scan better. Also helps with debugging.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have some validation code in mac80211 but said code will
force an invalid AID to 0 which isn't a valid AID either;
instead require a valid AID (1-2007) to be passed in from
userspace in cfg80211 already. Also move the code before
the race comment since it can only be executed during STA
addition and thus is not racy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race on access to last_request and its alpha2
through reg_is_valid_request() and us possibly processing
first another regulatory request on another CPU. We avoid
this improbably race by locking with the cfg80211_mutex as
we should have done in the first place. While at it add
the assert on locking on reg_is_valid_request().
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change, but it will make the race
fix easier to spot in my next patch.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change except we save a kfree(rd) and
allows us to clean this code up a bit after this. We do
avoid an unnecessary kfree(NULL) but calling that was OK too.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate RSC (NL80211_ATTR_KEY_SEQ) length in nl80211/cfg80211 instead
of having to do this in all the drivers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to nl80211 userspace can be very specific upon device
configuration. Before processing the request for the new HT40
channel types (HT40- or HT40+) we need to ensure we can use them
regulatory-wise. This wasn't required with wireless extensions as
specifying the channel type wasn't not available and configuration
was done towards the end implicitly upon association or reception
of beacons from the AP. For the new nl80211 we have to check this
when configuring the interfaces explicitly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nlmsg_new() adds the size of the netlink header to the value
that has been passed as parameter. If NLMSG_GOODSIZE is selected,
we request an allocation of one memory page plus the size of the
header. Instead, NLMSG_DEFAULT_SIZE should be used since it
already substracts the size of the Netlink header.
I have the impression that the similar naming in both constant
is error prone when using it with nlmsg_new(). This is already
documented in include/net/netlink.h
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a key with NL80211_CMD_NEW_KEY, we should allow the key
sequence number (RSC) to be set in order to allow replay protection to
work correctly for group keys. This patch documents this use for
nl80211 and adds the couple of missing pieces in nl80211/cfg80211 and
mac80211 to support this. In addition, WEXT SIOCSIWENCODEEXT compat
processing in cfg80211 is extended to handle the RSC (this was already
specified in WEXT, but just not implemented in cfg80211/mac80211).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_ATTR_CONTROL_PORT flag for NL80211_CMD_ASSOCIATE to
allow user space to indicate that it will control the IEEE 802.1X port
in station mode. Previously, mac80211 was always marking the port
authorized in station mode. This was enough when drop_unencrypted flag
was set. However, drop_unencrypted can currently be controlled only
with WEXT and the current nl80211 design does not allow fully secure
configuration. Fix this by providing a mechanism for user space to
control the IEEE 802.1X port in station mode (i.e., do the same that
we are already doing in AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is currently not possible to modify station flags, but that
capability would be very useful. This patch introduces a new
nl80211 attribute that contains a set/mask for station flags,
and updates the internal API (and mac80211) to mirror that.
The new attribute is parsed before falling back to the old so
that userspace can specify both (if it can) to work on all
kernels.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_STA_FLAG_MFP was forgotten from sta_flags_policy. The previous
version added the flag due to the loop used in parse_station_flags,
but the proper behavior would be to allow nla_parse_nested() to go
through the policy for all flags.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move key handling wireless extension ioctls from mac80211 to cfg80211
so that all drivers that implement the cfg80211 operations get wext
compatibility.
Note that this drops the SIOCGIWENCODE ioctl support for getting
IW_ENCODE_RESTRICTED/IW_ENCODE_OPEN. This means that iwconfig will
no longer report "Security mode:open" or "Security mode:restricted"
for mac80211. However, what we displayed there (the authentication
algo used) was actually wrong -- linux/wireless.h states that this
setting is meant to differentiate between "Refuse non-encoded packets"
and "Accept non-encoded packets".
(Combined with "cfg80211: fix a couple of bugs with key ioctls". -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_ASSOCIATE request must be able to indicate whether
management frame protection (IEEE 802.11w) is being used. mac80211 was
able to use MFP in client mode only with WEXT, but the new
NL80211_ATTR_USE_MFP attribute will allow this to be done with
nl80211, too.
Since we are currently using nl80211 for MFP only with drivers that
use user space SME, only MFP disabled and required values are
used. However, the NL80211_ATTR_USE_MFP attribute is an enum that can
be extended with MFP optional in the future, if that is needed with
some drivers (e.g., if the RSN IE is generated by the driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse complaint:
CHECK net/wireless/nl80211.c
net/wireless/nl80211.c:3694:6:
warning: symbol 'nl80211_send_mlme_timeout'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the JOIN_IBSS command look at the beacon interval
attribute to see if the user requested a specific beacon
interval, if not default to 100 TU (wext too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we leave an IBSS, we should clear the SSID and not just the
BSSID, but since WEXT allows configuring while the interface is
down we must not clear it when leaving due to taking the iface
down, so some complications are needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds IBSS API along with (preliminary) wext handlers.
The wext handlers can only do IBSS so you need to call them
from your own wext handlers if the mode is IBSS.
The nl80211 API requires
* an SSID
* a channel (frequency) for the case that a new IBSS
has to be created
It optionally supports
* a flag to fix the channel
* a fixed BSSID
The cfg80211 code also takes care to leave the IBSS before
the netdev is set down. If wireless extensions are used, it
also caches values when the interface is down and instructs
the driver to join when the interface is set up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When listing all wireless netdevs in the system this
is useful to print which wiphy they belong to. Just
add the attribute, any program that doesn't care will
just ignore it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary code and fields to let drivers specify
their cipher capabilities and exports them to userspace. Also
update mac80211 to export the ciphers it has.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This informs userspace when a change has occured on a world
roaming wiphy's channel which has lifted some restrictions
due to a regulatory beacon hint.
Because this is now sent to userspace through the regulatory
multicast group we remove the debug prints we used to use as
they are no longer necessary.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a netlink channel put helper, nl80211_msg_put_channel(),
which we will also make use of later for the beacon hints events.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of just passing the cfg80211-requested IEs, pass
the locally generated ones as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be
used to notify user space about locally detected Michael MIC failures.
This matches with the MLME-MICHAELMICFAILURE.indication() primitive.
Since we do not actually have TSC in the skb anymore when
mac80211_ev_michael_mic_failure() is called, that function is changed
to take in the TSC as an optional parameter instead of as a
requirement to include the TSC after the hdr field (which we did not
really follow). For now, TSC is not included in the events from
mac80211, but it could be added at some point.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, nl80211 mlme events were generated only for received
deauthentication and disassociation frames. We need to do the same for
locally generated ones in order to let applications know that we
disconnected (e.g., when AP does not reply to a probe). Rename the
nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they
are used for both received and locally generated frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AUTH_TYPE is a required parameter for
NL80211_CMD_AUTHENTICATE. We are currently (by chance) defaulting to
open system authentication if the attribute is not specified. It is
better to just reject the invalid command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes nl80211 to:
* validate that any IE input is a valid IE (stream)
* move some validation code before locking
* require that a reason code is given for both deauth/disassoc
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reports that there's a circular locking dependency;
this is because cfg80211_dev_rename() will acquire the
cfg80211_mutex while the device mutex is held, while
this normally is done the other way around. The solution
is to open-code the device-getting in nl80211_set_wiphy
and require holding the mutex around cfg80211_dev_rename
rather than acquiring it within.
Also fix a bug -- rtnl locking is expected by drivers so
we need to provide it.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When somebody tries to set the interface mode to the existing
mode, don't ask the driver but silently accept the setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the used authentication type and reason code are valid here
so that drivers/mac80211 do not need to care about this. In addition,
remove the unnecessary validation of SSID attribute length which is
taken care of by netlink policy.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen