If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.
With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move to circular buffers management macro and correct an error
with circular buffer initial condition.
Without this patch, the macb_tx_ring_avail() function was
not reporting the proper ring availability at startup:
macb macb: eth0: BUG! Tx Ring full when queue awake!
macb macb: eth0: tx_head = 0, tx_tail = 0
And hanginig forever...
I remove the macb_tx_ring_avail() function and use the
proven macros from circ_buf.h. CIRC_CNT() is used in the
"consumer" part of the driver: macb_tx_interrupt() to match
advice from Documentation/circular-buffers.txt.
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first register set is used for matching but
we support getting the initial hw addr from any of
the registers.
To prevent stale entries and false matches clear unused
register sets. This most important for the at91_ether
driver where u-boot always uses the 2nd register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all printk's to netdev_ counterparts and fix up some
printed texts.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used after gpio phy interrupt support was
removed from at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used on one AT91RM9200 board where a bootloader stores
the Ethernet address in the wrong order.
Support this on macb so address setting functions can be shared
with the at91_ether driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver in u-boot uses the first register set while
the at91_ether driver in u-boot uses the second register set.
By checking all register set, like at91_ether does, this code
can be shared between the drivers.
This only changes behavior on macb if no vaild address
is found in the first register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapt the error path, remove unneeded headers]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ethernet frame payload word-aligned, possibly making the
memcpy into the skb a bit faster. This will be even more important
after we eliminate the copy altogether.
Also eliminate the redundant RX_OFFSET constant -- it has the same
definition and purpose as NET_IP_ALIGN.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle all TX errors, not only underruns. TX error management is
deferred to a dedicated workqueue.
Reinitialize the TX ring after treating all remaining frames, and
restart the controller when everything has been cleaned up properly.
Napi is not stopped during this task as the driver only handles
napi for RX for now.
With this sequence, we do not need a special check during the xmit
method as the packets will be caught by TX disable during workqueue
execution.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macb_get_regs() ethtool function and its helper function:
macb_get_regs_len().
The version field is deduced from the IP revision which gives the
"MACB or GEM" information. An additional version field is reserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of masking head and tail every time we increment them, just let them
wrap through UINT_MAX and mask them when subscripting. Add simple accessor
functions to do the subscripting properly to minimize the chances of messing
this up.
This makes the code slightly smaller, and hopefully faster as well. Also,
doing the ring buffer management this way will simplify things a lot when
making the ring sizes configurable in the future.
Available number of descriptors in ring buffer function by David Laight.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some revision of GEM, TSR status register has more information.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has little meaning so remove it altogether and
let ethtool core fill in the fields automatically.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert some noisy netdev_dbg() statements to netdev_vdbg(). Defining
DEBUG will no longer fill up the logs; VERBOSE_DEBUG still does.
Add one more verbose debug for ISR status.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, add ISR status]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a couple of unneeded barriers and document the remaining ones.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Gigabit Ethernet mode to GEM cadence IP and enable RGMII connection.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following build failure on S390:
In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building macb on x86_64 the following warnings show up:
drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things:
* Use macb struct members and remove at91_ether ones
* Alloc DMA buffers on netdev start and dealloc on stop
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This rips out the at91_ether phy handling and ethtool stuff
and replace it with equivalent stuff from macb.
The only thing lost is the phy irq support from at91_ether,
but this can be added to macb and then benefit all users.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This will make it easier to share code between the drivers and
eventually merge them into one driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Use register and bits definitions from the macb header. This makes it
possible to have one header file for this hardware.
Process was scripted and the resulting object file has the same checksum.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
we are currently returning ENODEV, as the clk_get may give a exact
error code in its returned pointer, assign it to the ret by using the
PTR_ERR function, so that the subsequent goto label will jump to the
error path and clean the driver and return the error correctly.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OFF carrier state is setup in probe() open() and suspend() functions.
The carrier ON state is managed in macb_handle_link_change().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the gpio_to_irq() function to retrieve the phy IRQ line
from the GPIO pin specification.
This fix is needed now that we have moved to irqdomains on AT91.
Reported-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT91RM9200 Ethernet controller still has a fixed IO mapping.
So:
* Remove the fixed IO mapping and AT91_VA_BASE_EMAC definition.
* Pass the physical base-address via platform-resources to the driver.
* Convert at91_ether.c driver to perform an ioremap().
* Ethernet PHY detection needs to be performed during the driver
initialization process, it can no longer be done first.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the build of the macb driver that was broken by the DT changes:
drivers/net/ethernet/cadence/macb.c:1503: error: implicit declaration of function 'of_match_ptr'
drivers/net/ethernet/cadence/macb.c:1503: error: 'macb_dt_ids' undeclared here (not in a function)
drivers/net/ethernet/cadence/macb.c:1503: error: initializer element is not constant
drivers/net/ethernet/cadence/macb.c:1503: error: (near initialization for 'macb_driver.driver.of_match_table')
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.
For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David S. Miller <davem@davemloft.net>
Allow the device tree to provide the mac address and the phy mode.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
GEM has configurable receive buffer sizes so requires this to be
programmed up. Any size < 2048 and a multiple of 64 bytes is permitted.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Some GEM implementations may support DMA bus widths up to 128 bits. We
can get the maximum supported DMA bus width from the design
configuration register so use that to program the device up.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
GEM devices have a different number of statistics registers and they
are at a different offset to MACB devices. Make the statistics
collection method dependent on device type.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on the
device type.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Cadence GEM is based on the MACB Ethernet controller but has a few
small changes with regards to register and bitfield placement. This
patch detects the presence of a GEM by reading the module ID register
and setting a flag appropriately.
This handles the new HW address, USRIO and hash register base register
locations in GEM.
v3: - convert to macb_is_gem() inline rather than storing a boolean
flag
- handle rx_overrun stats for gem
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
macb is already using the dev_dbg() and friends helpers so use netdev_()
along with a pr_fmt() definition to make the printing a little cleaner.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin. Create a common
macb_platform_data for macb that both at91 and avr32 can use. In
future we can use this to support other architectures that use the
same IP block with the macb driver.
v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91 now provides both "pclk" and "hclk" aliases for the the macb
device so we can use the same clk handling paths for both AT91 and
AVR32.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
so the defconfig of the atmel continue to have the support of the network
as before
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Joachim Eastwood