The V4L2 flash interface allows controlling multiple LEDs through a single
sub-devices if, and only if, these LEDs are of different types. This
approach scales badly for flash controllers that drive multiple flash LEDs
or for LED specific associations. Essentially, the original assumption of a
LED driver chip that drives a single flash LED and an indicator LED is no
longer valid.
Address the matter by registering one sub-device per LED.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (for greybus/light)
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check memory allocation failure and return -ENOMEM in such a case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A debug printk statement was copied incorrectly into the new
csi1 parser code and causes a warning there:
drivers/media/platform/omap3isp/isp.c: In function 'isp_probe':
include/linux/dynamic_debug.h:134:3: error: 'i' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since there is only one lane, the index is never set. This
changes the debug print to always print a zero instead,
keeping the original format of the message.
Fixes: 9211434bad ("media: omap3isp: Parse CSI1 configuration from the device tree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings when building on i386:
drivers/media/platform/qcom/camss-8x16/camss-csiphy.c:333:22: warning: constant 1000000000000 is so big it is long long
drivers/media/platform/qcom/camss-8x16/camss-csiphy.c:339:32: warning: constant 1000000000000 is so big it is long long
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add abbreviations explanation at the top header blocks in source files.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use standard V4L2 control to get pixel clock rate from a sensor
linked in the media controller pipeline. Then calculate clock
rates on CSIPHY, CSID and VFE to use the lowest possible.
If the currnet pixel clock rate of the sensor cannot be read then
use the highest possible. This case covers also the CSID test
generator usage.
If VFE is already powered on by another pipeline, check that the
current VFE clock rate is high enough for the new pipeline.
If not return busy error code as VFE clock rate cannot be changed
while VFE is running.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add crop module configuration support to be able to apply cropping.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add scaler module configuration support to be able to apply scaling.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use VFE PIX input interface and do format conversion in VFE.
Supported input format is UYVY (single plane YUV 4:2:2) and
its different sample order variations.
Supported output formats are:
- NV12/NV21 (two plane YUV 4:2:0)
- NV16/NV61 (two plane YUV 4:2:2)
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add Makefile and update platform/Kconfig and platform/Makefile
to enable building of the QCom CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files handle the video device nodes of the camss driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the VFE module. The VFE has different input
interfaces. The PIX input interface feeds the input data to an image
processing pipeline. Three RDI input interfaces bypass the image
processing pipeline. The VFE also contains the AXI bus interface which
writes the output data to memory.
RDI interfaces are supported in this version. PIX interface is not
supported.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the ISPIF module which handles the routing of the data
streams from the CSIDs to the inputs of the VFE.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the CSID modules which handle the protocol and
application layer of the CSI2 receivers.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the CSIPHY modules which are responsible for the
physical layer of the CSI2 receivers.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These formats are compressed 12-bit raw bayer formats with four different
pixel orders. They are similar to 10-bit variants. The formats added by
this patch are
V4L2_PIX_FMT_SBGGR12P
V4L2_PIX_FMT_SGBRG12P
V4L2_PIX_FMT_SGRBG12P
V4L2_PIX_FMT_SRGGB12P
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The calculation of the left volume looks suspect, the value of
0x1f - ((val << 8) & 0x1f) is always 0x1f. The debug prior to the
assignment of value[1] prints the left volume setting using the
calculation 0x1f - (val >> 8) & 0x1f which looks correct to me.
Fix the left volume by using the correct expression as used in
the debug.
Detected by CoverityScan, CID#146140 ("Wrong operator used")
Fixes: 850d24a5a8 ("[media] em28xx-alsa: add mixer support for AC97 volume controls")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
videobuf_queue_ops are not supposed to change at runtime. All functions
working with videobuf_queue_ops provided by <media/videobuf-core.h> work
with const videobuf_queue_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
videobuf_queue_ops are not supposed to change at runtime. All functions
working with videobuf_queue_ops provided by <media/videobuf-core.h> work
with const videobuf_queue_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
videobuf_queue_ops are not supposed to change at runtime. All functions
working with videobuf_queue_ops provided by <media/videobuf-core.h> work
with const videobuf_queue_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change the alignment restriction for output type of buffers
only, also set corect input resolution and fill bidirectional
vb2 queue flag in order to map output type buffers read/write.
The last is needed by encoder firmware to add padding at the
bottom of output (input buffers).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change is intended to give to the v4l2 drivers a choice to
change the default behavior of the v4l2-core DMA mapping direction
from DMA_TO/FROM_DEVICE (depending on the buffer type CAPTURE or
OUTPUT) to DMA_BIDIRECTIONAL during queue_init time.
Initially the issue with DMA mapping direction has been found in
Venus encoder driver where the hardware (firmware side) adds few
lines padding on bottom of the image buffer, and the consequence
is triggering of IOMMU protection faults.
This will help supporting venus encoder (and probably other drivers
in the future) which wants to map output type of buffers as
read/write.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implements g_/s_selection crop support by using DCMI crop
hardware feature.
User can first get the maximum supported resolution of the sensor
by calling g_selection(V4L2_SEL_TGT_CROP_BOUNDS).
Then user call to s_selection(V4L2_SEL_TGT_CROP) will reset sensor
to its maximum resolution and crop request is saved for later usage
in s_fmt().
Next call to s_fmt() will check if sensor can do frame size request
with crop request. If sensor supports only discrete frame sizes,
the frame size which is larger than user request is selected in
order to be able to match the crop request. Then s_fmt() resolution
user request is adjusted to match crop request resolution.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Test cookie return by dmaengine_submit() and return error if any.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid using a generic name such as MAX_DATA_LANES in a header file widely
included in drivers. Instead, call it V4L2_FWNODE_CSI2_MAX_DATA_LANES.
Fixes: 4ee236219f ("media: v4l2-fwnode: suppress a warning at OF parsing logic")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock lane is the first lane in the lane_polarities array. Reflect this
consistently by putting the number of data lanes after the number of clock
lanes.
Fixes: 4ee236219f ("media: v4l2-fwnode: suppress a warning at OF parsing logic")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
fwnode_property_read_u32_array() only returns the number of array elements
if the array argument is NULL. The assumption that it always did so lead to
lane-polarities properties never being read.
Fixes: 4ee236219f ("media: v4l2-fwnode: suppress a warning at OF parsing logic")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ACPI match table is empty. Remove it.
Also convert the drive to use probe_new callback in struct i2c_driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No one of the supported Venus version has implemented VP9 codec
for enconding, so drop it from the list of codecs.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the helper function in decoder and encoder find_format
to runtime check supported codecs.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a helper function to runtime check supported encoder and
decoder codecs depending on venus version and platform.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fills missing (forgotten) video device name with
appropriate string so that udev can distinguishes between
decoder and encoder devices.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without PM support gcc could warns about unused functions, thus
mark runtime_suspend/resume as __maybe_unused.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation or
are stored in the algo field of i2c_adapter structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in this driver.
This also adds the CEC_CAP_RC capability which was missing here
(and this is also the reason for this new define, to avoid missing
such capabilities).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Only the first HDMI input has a CEC adapter, so just report 'HDMI 0' as
the HDMI input name.
For the HDMI outputs use bus_cnt instead of i as the output number.
The HDMI name now corresponds to what 'v4l2-ctl --list-outputs' reports.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support to emulate CEC pin monitoring. There are few hardware devices
that support this, so being able to emulate it here helps developing
software for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current CEC pin value (0 or 1) was part of the cec_pin struct,
but that assumes that CEC pin monitoring can only be used with
a driver that uses the low-level CEC pin framework.
But hardware that has both a high-level API and can monitor the
CEC pin at low-level at the same time does not need to depend on
the cec pin framework.
To support such devices remove the cur_value field from struct cec_pin
and add a cec_pin_is_high field to cec_adapter. This also makes it
possible to drop the '#ifdef CONFIG_CEC_PIN' in cec-api.c.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the adapter is removed the cec_delete_adapter() call attempts
to set the physical address to INVALID by calling __cec_s_phys_addr()
and so disabling the adapter.
However, __cec_s_phys_addr checks if the device node was unregistered
and just returns in that case.
This means that the adap_enable callback is never called with 'false'
to disable the CEC adapter. Most drivers don't care, but some need
to do cleanup here.
Change the test so the adapter is correctly disabled, even when the
device node is unregistered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This Kaffeine's BZ:
https://bugs.kde.org/show_bug.cgi?id=374693
affects SkyStar S2 PCI DVB-S/S2 rev 3.3 device. It could be due to
a Kernel bug.
While checking the Isil 6421, comparing with its manual, available at:
http://www.intersil.com/content/dam/Intersil/documents/isl6/isl6421a.pdf
It was noticed that, if the output load is highly capacitive, a different approach
is recomended when energizing the LNBf.
Also, it is possible to detect if a current overload is happening, by checking an
special flag.
Add support for it.
Tested on Skystar S2. Changes respect override_or option so should still work fine
on cx88 based cards which disable dynamic current limit.
Changes since v1:
v2 - fixed incorrect checking of i2c return values
v3 - fix if logic to check if dcl needs re-enabling
- respect override_or values which aim to disable dcl
- only do long sleep on overload if dcl enabled
- add short sleep before re-enabling dcl
- only check overload and potentially return EINVAL if device is on
v4 - revert v3 sleep logic changes to remove tuning delays
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Cleans up smatch warning:
symbol 'stvlist' was not declared. Should it be static?
Patch originally submitted by Colin Ian King <colin.king@canonical.com>,
remainder after the merge of all other stv0910 fixes.
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 'Press and Hold' operation was not correctly implemented, in
particular the requirement that the repeat doesn't start until
the second identical keypress arrives. The REP_DELAY value also
had to be adjusted (see the comment in the code) to achieve the
desired behavior.
The 'enabled_protocols' field was also never set, fix that too. Since
CEC is a fixed protocol the driver has to set this field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC needs a keypress timeout of 550ms, which is too high for the IR
protocols. Also fill in known repeat times, with 50ms error margin.
Also, combine all protocol data into one structure.
Signed-off-by: Sean Young <sean@mess.org>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Any protocol for which we have a software decoder, can be enabled. Without
this only the loaded protocol decoders can be selected.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If rc_validate_filter() is called for CEC or XMP, then we would read
beyond the end of the array.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.
Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.
Verified on a HVR-1150 and Raspberry Pi.
Fixes: 3f5c4c7332 ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpio-ir-recv driver adds timeouts which the saa7134 lacks; this
causes keypress not to arrive, and to only arrive once more IR is
received. This is what the commit below calls "ghost keypresses",
and that commit does not solve the issue completely.
This makes the IR on the HVR-1150 much more reliable and responsive.
Fixes: 3f5c4c7332 ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpio-ir-recv driver does many wakeups (once per edge); the saa7134
driver has special handling to only wakeup 15ms after the first edge.
Make this part of rc-core so gpio-ir-recv also benefits from
this (so a rc-5 keypress now causes 3 wakeups rather than 24).
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We're reading beyond the buffer before checking its length.
BUG: KASAN: slab-out-of-bounds in wbcir_irq_tx
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This causes out-of-bounds read on device probe.
BUG: KASAN: slab-out-of-bounds in mceusb_dev_printdata+0xdc/0x830 [mceusb]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It adds the remote control driver and corresponding keymap file for
IRDEC block found on ZTE ZX family SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The NEC scancode composing and protocol type detection in
ir_nec_decode() is generic enough to be a shared function. Let's create
an inline function in rc-core.h, so that other remote control drivers
can reuse this function to save some code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Transmit support in this driver was never tested and based on the code
it can't work. Just one example:
The buffer provided to nvt_tx_ir holds unsigned int values in
micro seconds: First value is for a pulse, second for a pause, etc.
Bytes in this buffer are copied as-is to the chip FIFO what can't work
as the chip-internal format is totally different. See also conversion
done in nvt_process_rx_ir_data.
Even if we would try to fix this we have the issue that we can't test
it. There seems to be no device on the market using IR transmit with
one of the chips supported by this driver.
To facilitate maintenance of the driver I'd propose to remove the
rudimentary transmit support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is new driver which uses pwm, so it is more power-efficient
than the bit banging gpio-ir-tx driver.
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a simple bit-banging GPIO IR TX driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without this patch, an input device is created which is not necessary.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11605 880 20 12505 30d9 drivers/media/rc/rc-main.o
File size After adding 'const':
text data bss dec hex filename
11797 720 20 12537 30f9 drivers/media/rc/rc-main.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
18551 2256 77 20884 5194 drivers/media/rc/imon.o
File size After adding 'const':
text data bss dec hex filename
18679 2160 77 20916 51b4 drivers/media/rc/imon.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unnecessary static on local variable delt.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
5009 3456 576 9041 2351 drivers/media/rc/sir_ir.o
after:
text data bss dec hex filename
4988 3400 512 8900 22c4 drivers/media/rc/sir_ir.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no dependency between the two, so remove the dependency in
Kconfig files.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for CIR controller on MT7622 SoC. It has similar
handling logic as the previously MT7623 does, but there are some
differences in the register and field definition. So for ease portability
and maintenance, those differences all are being kept inside the platform
data as other drivers usually do. Currently testing successfully on NEC
and SONY remote controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch is the preparation patch in order to adapt into various
hardware through adding platform data which holds specific characteristics
and differences among MediaTek supported CIR devices instead of the old
way defining those data in the static way as macro has. And the existing
logic would be slightly changed to operate on those data which the actual
device depends on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The NEC decoder and the Sanyo decoders check if dev->keypressed is true
before calling rc_repeat (without holding dev->keylock).
Meanwhile, the XMP and JVC decoders do no such checks.
This patch makes sure all users of rc_repeat() do so consistently by
removing extra checks in NEC/Sanyo and modifying the check a bit in
rc_repeat() so that no input event is generated if the key isn't pressed.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The configuration of the pipeline and entities directly affects the
inputs required to each entity for the partition algorithm. Thus it
makes sense to involve those entities in the decision making process.
Extend the entity ops API to provide an optional .partition() operation.
This allows entities that affect the partition window to adapt the
window based on their configuration.
Entities implementing this operation must update the window parameter in
place, which will then be passed up the pipeline. This creates a process
whereby each entity describes what is required to satisfy the required
output to its predecessor in the pipeline.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide register definitions required for UDS phase and partition
algorithm support. The registers and bits defined here are available on
Gen3 hardware only.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we develop the partition algorithm, we need to store more information
per partition to describe the phase and other parameters.
To keep this data together, further abstract the existing v4l2_rect
into a partition specific structure. As partitions only have horizontal
coordinates, store the left and width values only.
When generating the partition windows, operate directly on the partition
struct rather than copying and duplicating the processed data
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vsp1_pipe object context variables for div_size and
current_partition allowed state to be maintained through processing the
partitions during processing.
Now that the partition tables are calculated during stream on, there is
no requirement to store these variables in the pipe object.
Utilise local variables for the processing as required.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously the active window and partition sizes for each partition were
calculated for each partition every frame. This data is constant and
only needs to be calculated once at the start of the stream.
Extend the vsp1_pipe object to dynamically store the number of partitions
required and pre-calculate the partition sizes into this table.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Separate the code change from the function move so that code changes can
be clearly identified. This commit has no functional change.
The partition algorithm functions will be changed, and
vsp1_video_pipeline_setup_partitions() will call vsp1_video_partition().
To prepare for that, move the function without any code change.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Presently any received buffers are only released back to vb2 if
vsp1_video_stop_streaming() is called. If vsp1_video_start_streaming()
encounters an error, we will be warned by the vb2 handlers that buffers
have not been returned.
Move the buffer cleanup code to its own function to prevent duplication
and call from both vsp1_video_stop_streaming() and the error path in
vsp1_video_start_streaming().
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, vblank range given to user was too big, falling outside
of permissible range for a given resolution. Sometimes, too low vblank
resulted in errors.
Now, limit vblank to only permissible range for a given resolution.
This change limits lower-bounds of vblank, doesn't affect upper bounds.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Matthias Schwarzott