We need a bit book keeping around power wells' ops->enable(), namely a
nice debug message and updating hw_enabled. Let's introduce a
intel_power_well_enable() function to make sure all the callers do the
same things.
v2 (from Paulo):
- s/i915_power_well_enable/intel_power_well_enable/ since everything
else on this file uses intel_ instead of i915_.
- Fix typo in commit message.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We do the exact same steps around the disp2d/pipe A power well
enable/disable on VLV and CHV. Refactor the shared code into
some helpers.
Note that this means we now call vlv_power_sequencer_reset() before
turning off the power well, whereas before we did it after. That
doesn't matter though since vlv_power_sequencer_reset() just resets
the power sequencer software tracking and doesn't touch the hardware
at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe A power well is the "disp2d" well on CHV and pipe B and C wells
don't even exist. Thereforce we can remove the checks for pipe A vs.
others and just assume it's always pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the spurious 'A' from the VLV/CHV ref clock enable define,
and add the "REF" to the VLV ref clock selection bit. Also
s/CLOCK/CLK/ for extra consistency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable the DPLL VGA mode when enabling the DPLL, but we enaable it
again when disabling the DPLL. Having VGA mode enabled even in unused
DPLLs can cause problems for CHV, so it seems wiser to always keep it
disabled. And let's just do that on all GMCH platforms to keep things
as similar as possible between them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Expecting CHV power wells to be just an extended versions of the VLV
power wells, a bunch of commented out power wells were added in
anticipation when Punit folks would implement it all. Turns out they
never did, and instead CHV has fewer power wells than VLV. Rip out all
the #if 0'ed junk that's not needed.
v2: Rename the "pipe-a" well to "display" to match VLV
Clarify the pipe A power well relationship to pipes B and C (Deepak)
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not sure which LDO programming sequence delay should be used for the CHV
PHY, but the spec says that 600ns is "Used by default for initial
bringup", and the BIOS seems to use that, so let's do the same.
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fix spelling typo in intel_runtime_pm.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With recent hardware/firmware there don't appear to be any glitches
on the other PHY when we toggle the cmnreset for the other PHY. So
detangle the cmnlane power wells from one another and let them be
controlled independently.
This reverts commit 3dd7b97458.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sometimes (exactly when is a bit unclear) DISPLAY_PHY_CONTROL appears to
get corrupted. The values I've managed to read from it seem to have some
pattern but vary quite a lot. The corruption doesn't seem to just happen
when the register is accessed, but can also happen spontaneosly during
modeset. When this happens during a modeset things go south and the
display doesn't light up.
I've managed to hit the problemn when toggling HDMI on port D on and
off. When things get corrupted the display doesn't light up, but as soon
as I manually write the correct value to the register the display comes
up.
First I was suspicious that we ourselves accidentally overwrite it with
garbage, but didn't catch anything with the reg_rw tracepoint. Also I
sprinkled check all over the modeset path to see exactly when the
corruption happens, and eg. the read back value was fine just before
intel_dp_set_m(), and corrupted immediately after it. I also made my
check function repair the register value whenever it was wrong, and with
this approach the corruption repeated several times during the modeset
operation, always seeming to trigger in the same exact calls to the
check function, while other calls to the function never caught anything.
So far I've not seen this problem occurring when carefully avoiding all
read accesses to DISPLAY_PHY_CONTROL. Not sure if that's just pure luck
or an actual workaround, but we can hope it works. So let's avoid reading
the register and instead track the desired value of the register in dev_priv.
v2: Read out the power well state to determine initial register value
v3: Use DPIO_CHx names instead of raw numbers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs tell us to ungate PG1 and Misc I/O at display init. We'll use
the PLLS power domain to ensure those two power wells are up.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Warn if the conditions to enter or exit DC6 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.
v2: Removed camelcase in functions and variables.
v3: Do some minimal check to assert if CSR program is not loaded.
v4:
1] Correct the check for backlight-disabling in assert_can_enable_dc6().
2] Check csr.loaded = false before disabling DC6 and simplify other checks.
v5:
1] Remove checks for DC5 state from assert_can_enable_dc6 function as DC5 is no
longer enabled before enabling DC6.
2] Correct the check for CSR-loading in assert_can_disable_dc6 function as CSR must
be loaded for context restore to happen on DC6 disabling.
v6:
1] It's okay to explicitly disable DC6 during driver-load/resume even though it might
already be disabled and so don't warn about it.
v7: Rebase to latest.
v8: Sqashed the patch from Imre -
[PATCH] drm/i915/skl: avoid false CSR fw not loaded WARN during driver load/resume
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: During initialization added a early return before disabling DC5. (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch just implements the basic enable and disable
functions of DC6 state which is needed for SKL platform.
Its important to load SKL CSR program before calling enable.
DC6 is a deeper power saving state where hardware dynamically
disables power well 0 and saves the associated registers.
DC6 can be entered when software allows it, the conditions
for DC5 are met, and the PCU allows DC6.
DC6 cannot be used if the backlight is being driven from the
display utility pin.
Its better to configure display engine to have power well 2
disabled before getting into DC6 enable function. Hence rpm
framework will ensure to check status of power well 2 and DC5
before calling skl_enable_dc6.
v2: Replace HAS_ with IS_ check as per Daniel's review comments
v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.
v4: No need to call gen9_disable_dc5 inside enable sequence of
DC6, as its already take care above.
v5: call POSTING_READ for every write to a register to ensure that
its written immediately.
Call intel_prepare_ddi during DC6 exit as it's required on low-power exit.
v6: Protect DC6-enabling-disabling functionality with locks to synchronize
with CSR-loading code.
v7: Remove grabbing CSR-related mutex in skl_enable/disable_dc6 functions as
deferred DC5-enabling functionality is now removed.
v8: Remove 'Disabling DC5' from the debug comment during DC6 enabling as when
DC6 is allowed, DC5 is not programmed at all.
v9:
- Rebase to latest.
- Move all DC6-related functions from intel_display.c to intel_runtime_pm.c.
v10: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add triggers for DC6 as per details provided in skl_enable_dc6
and skl_disable_dc6 implementations.
Also Call POSTING_READ for every write to a register to ensure
it is written to immediately
v1: Remove POSTING_READ and intel_prepare_ddi calls as they've been added in previous patches.
v2:
1] Remove check for backlight disabled as it should be the case by that time.
2] Mark DC5 as disabled when enabling DC6.
3] Return from DC5-disabling function early if DC5 is already be disabled which can happen
due to DC6-enabling earlier.
3] Ensure CSR firmware is loaded after resume from DC6 as corresponding memory contents won't
be retained after runtime-suspend.
4] Ensure that CSR isn't identified as loaded before CSR-loading program is called during
runtime-resume.
v3: Rebase to latest
Modified as per review comments from Imre and after discussion with Art:
1] DC6 should be preferably enabled when PG2 is disabled by SW as the check for PG1 being
disabled is taken of by HW to enter DC6, and disabled when PG2 is enabled respectively.
This helps save more power, especially in the case when display is disabled but GT is
enabled. Accordingly, replacing DC5 trigger sequence with DC6 for SKL.
2] DC6 could be enabled from intel_runtime_suspend() function, if DC5 is already enabled.
3] Move CSR-load-status setting code from intel_runtime_suspend function to a new function.
v4:
1] Enable/disable DC6 only when toggling the power-well using a newly defined macro ENABLE_DC6.
v5:
1] Load CSR on system resume too as firmware may be lost on system suspend preventing
enabling DC5, DC6.
2] DDI buffers shouldn't be programmed during driver-load/resume as it's already done
during modeset initialization then and also that the encoder list is still uninitialized by
then. Therefore, call intel_prepare_ddi function right after disabling DC6 but outside
skl_disable_dc6 function and not during driver-load/resume.
v6:
1] Rebase to latest.
2] Move SKL_ENABLE_DC6 macro definition from intel_display.c to intel_runtime_pm.c.
v7:
1) Refactored the code for removing the warning got from checkpatch.
2) After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v8:
- Reverted the changes done in v7.
- Removed the condition check in skl_prepare_resune(). (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Warn if the conditions to enter or exit DC5 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.
v2: Removed camelcase in functions and variables.
v3: Do some minimal check to assert if CSR program is not loaded.
v4:
1] Used an appropriate function lookup_power_well() to identify power well,
instead of using a magic number which can change in future.
2] Split the conditions further in assert_can_enable_DC5() and added more checks.
3] Removed all WARNs from assert_can_disable_DC5 as they were unnecessary and added two
new ones.
4] Changed variable names as updated in earlier patches.
v5:
1] Change lookup_power_well function to take an int power well id.
2] Define a new intel_display_power_well_is_enabled helper function to check whether a
particular power well is enabled.
3] Use CSR-related mutex in assert_csr_loaded function.
v6: Remove use of dc5_enabled variable as it's no longer needed.
v7:
1] Rebase to latest.
2] Move all DC5-related functions from intel_display.c to intel_runtime_pm.c.
v8: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v9: Modified below changes based on review comments from Imre.
- Moved intel_display_power_well_is_enabled() to intel_runtime_pm.c.
- Removed mutex lock from assert_csr_loaded(). (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch just implements the basic enable and disable
functions of DC5 state which is needed for both SKL and BXT.
Its important to load respective CSR program before calling
enable, which anyways will happen as CSR program is executed
during boot.
DC5 is a power saving state where hardware dynamically disables
power well 1 and the CDCLK PLL and saves the associated registers.
DC5 can be entered when software allows it, power well 2 is
disabled, and hardware detects that all pipes are disabled
or pipe A is enabled with PSR active.
Its better to configure display engine to have power well 2 disabled before
getting into DC5 enable function. Hence rpm framework will have to
ensure to check status of power well 2 before calling gen9_enable_dc5.
Rather dc5 entry criteria should be decided based on power well 2 status.
If disabled, then call gen9_enable_dc5.
v2: Replace HAS_ with IS_ check as per Daniel's review comments
v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.
v4: call POSTING_READ for every write to a register to ensure that
its written immediately.
v5: Modified as per review comments from Imre.
- Squashed register definitions into this patch.
- Finetuned comments and functions.
v6:
Avoid redundant writes in gen9_set_dc_state_debugmask_memory_up function.
v7:
- Rebase to latest.
- Move all runtime PM functions defined in intel_display.c to
intel_runtime_pm.c.
v8: Rebased to drm-intel-nightly. (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.
Also call POSTING_READ for every write to a register to ensure that
its written immediately.
v1: Remove POSTING_READ calls as they've already been added in previous patches.
v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.
Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
to warnings. However, removing them for now as they'll be included in a future patch
asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
accessed during deferred DC5-enabling, are not initialized earlier.
v3: Rebase to latest.
Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5 for simplicity, instead of
deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.
v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.
v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.
v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)
v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.
v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Modified as per review comments from Imre
- Mention enabling instead of allowing in the debug trace and
remove unnecessary comments.
v3:
- Rebase to latest.
- Move DC9-related functions from intel_display.c to intel_runtime_pm.c.
v4: (imre)
- remove DC5 disabling, it's a nop at this point
- squashed in Suketu's "Assert the requirements to enter or exit DC9"
patch
- remove check for RUNTIME_PM from assert_can_enable_dc9, it's not a
dependency
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v3)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add BXT power domains
v2: Use DOMAIN_PLLS instead of a new CDCLK one, whitespace fixes
(Damien)
v3: add VGA, TRANSCODER_A power domains (imre)
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was dumping the DDI translation tables to make sure my patch updating
the HDMI entry was doing the right thing when I noticed that the table
was showing reset values after DPMS.
And indeed, the DDI translation registers are in power well 1 on SKL,
and so we're losing their values when shutting down eDP.
Calling intel_prepare_ddi() on PW1 enabling re-programs the table.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't use this function on gen9, no need for that test here.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe interrupt registers are in the actual pipe power well, so we
need to restore them when re-enable the corresponding power well.
I've also copied what we do on HSW/BDW for VGA, even if the we haven't
enabled unclaimed registers just yet.
v2: Don't run skl_power_well_post_enable() if the power well is already
enabled (Paulo)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just to be more consistent with what we do on HSW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like what we do for HSW/BDW, having those variables makes it a bit
easier to parse the code.
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While we only need to restore pipe B/C interrupt registers on BDW when
enabling the power well, skylake a bit more flexible and we'll also need
to restore the pipe A registers as it has its own power well that can be
toggled.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements core logic of SKL display power well.
v2: Addressed Imre's comments
- Added respective DDIs under power well #1 and #2
- Simplified repetitive code in power well programming
v3: Implemented Imre's comments
- Further simplified power well programming
- Made sure that PW 1 is enabled prior to PW 2
v4: Fix minor conflict with the the cherryview support (Damien)
v5: Add the PLL power domain to the always on power well (Damien)
v6: Disable BIOS power well (Imre)
Use power well data for comparison (Imre)
Put the PLL power domain into PW1 as its needed for CDCLK (Satheesh,
Damien)
v7: Addressed Imre's comments
- Lowered the time out to 1ms
- Added parantheses in macro
- Moved debug message and fixed wait_for interval
v8:
- Add a WARN() when swiching on an unknown power well (Imre, done by Damien)
- Whitespace fixes (spaces instead of tabs) (Damien)
v9: (Imre, done by Damien)
- Merge the register definitions with this patch
- Merge the MISC IO power well in this patch
v10: (Imre, done by Damien)
- Define the Misc I/O power domains to be the power well 1 ones as Misc I/O
needs to be enabled with PW1
- Added Transcoder A and VGA domains to PW 2
- Remove the MISC_IO power domains as well in the the always on
domains definition
- Move Misc I/O power well at the top of the power well list so it's turned
on right after PW1.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3,v6,v7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding new power doamins for AUX controllers
v2: Added new power domains in power_domain_str per Imre's comment
v3: Added AUX power domains to older platforms
v4: Rebase on top of POWER_DOMAIN_PLLS.
v5: Modified to address review comments from Imre
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After switching to using the component interface this API isn't needed
any more.
v2-3: unchanged
v4:
- move the removal of i915_powerwell.h to this patch (Takashi)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
pps_{lock,unlock}() call intel_display_power_{get,put}() outside
pps_mutes to avoid deadlocks with the power_domain mutex. In theory
during aux transfers we should usually have the relevant power domain
references already held by some higher level code, so this should not
result in much overhead (exception being userspace i2c-dev access).
However thanks to the check_power_well() calls in
intel_display_power_{get/put}() we end up doing a few Punit reads for
each aux transfer. Obviously doing this for each byte transferred via
i2c-over-aux is not a good idea.
I can't think of a good way to keep check_power_well() while eliminating
the overhead, so let's just remove check_power_well() entirely.
Fixes a driver init time regression introduced by:
commit 773538e860
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:56 2014 +0300
drm/i915: Reset power sequencer pipe tracking when disp2d is off
Credit goes to Jani for figuring this out.
v2: Add the regression note in the commit message.
Cc: stable@vger.kernel.org (v3.18+)
Cc: Egbert Eich <eich@suse.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86201
Tested-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Many distro's have mechanism in place to collect and automatically file
bugs for failed WARN()s. And since i915 has a lot of hw state sanity
checks which result in WARN(), it generates quite a lot of noise which
is somewhat disconcerting to the end user.
Separate out the internal hw-is-in-the-state-I-expected checks into
I915_STATE_WARN()s and allow configuration via i915.verbose_checks module
param about whether this will generate a full blown stacktrace or just
DRM_ERROR(). The new moduleparam defaults to true, so by default there
is no change in behavior. And even when disabled, you will still get
an error message logged.
v2: paint the macro names blue, clarify that the default behavior
remains the same as before
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's the version actually taking the dev_priv->power_domains lock.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On chv the pipe-a power well is the new disp2d well, and it kills pretty
much everything in the display block. So we need to do the the same
dance that vlv does wrt. display irqs and hpd when the power well goes
up or down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that the pipe-a power well has replaced the disp2d power well
on chv. At least that's the case with the current punit firmware. So
enable the pipe-a power and expand its domains to cover everything the
disp2d well ought to cover.
The other power wells (apart from the cmnlane wells) still seem awol
in the current punit firmware. So leave them disabled in the code.
This fixes a hilarious oops during resume on bsw where
intel_hdmi_get_config() would read the port register and get back
0xffffffff and thus think the port is enabled on pipe D. It would then
go and index the pipe_to_crtc_mapping[] array with PIPE_D and blow up
when intel_hdmi_get_config() tries to write to crtc->config. Someone
really ought to replace all naked pipe_to_crtc_mapping[] uses with the
appropriate function call so we could add a warning there if the pipe
doesn't actually exist...
We must also call the power seqeuencer state reset function from
the pipe-a well disable just like we do from disp2d on vlv. Otherwise
the eDP panel won't recover at resume time since the PPS has lost its
hold on the port.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84903
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case the cmnlane power well is down but cmnreset isn't asserted we
would currently skip the off+on toggle for the power well. That could
leave cmnreset deasserted while cmnlane is powered down which might
lead to problems with the PHY.
To avoid such issues skip the cmnlane toggle only if both cmnlane and
disp2d wells are up and cmnreset is already deasserted. In all other
cases power down the cmnlane well which will also make sure cmnreset
gets asserted correctly while cmnlane is powered down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only run it after we actually enable the power well. When we're
booting the machine there are cases where we run
hsw_power_well_post_enable without really needing, and even though
this is not causing any real bugs, it is unneeded and causes confusion
to people debugging interrupts.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the new world order!
Not going full monty on these here and rolling this out throughout the
subsequent call chains since this is just for the kerneldoc. Later on
we can go more crazy, especially once we've embedded drm_device
correctly.
v2: Also frob the runtime_pm functions ...
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've decided not to document the functions exported to the audio
driver since really, they shouldn't exist ...
v2: Improvements from Imre's review plus a few more spelling fixes
I've spotted.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allows us to mark it static and so forgoe the kerneldoc for it.
Note that intel_power_domains_fini is also called from failure paths
in the driver load sequence. But the call to runtime_pm_disable for
that is harmless since by default runtime pm is already disabled.
v2: Augment the commit message as discussed with Imre on irc.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've decided to not move intel_display_port_power_domain because
that's just a hack in our design ...
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- fini goes with init, so call it intel_power_domains_fini. While
at it shovel some of the fini code that leaked out of it back in.
- give power_enabled functions the verb _is_ to make the meaning clearer.
Also use a __ prefix instead of _unlocked to really discourage users.
- rename runtime_pm_init/fini to enable/disable since that's what they do.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Geez is the audio hack ugly.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Rebased on top of the skl patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau