Oddly, GENMASK() requires signed bit numbers, so that it can compare
them for < 0. If passed an unsigned type, we get warnings about the
test never being true.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_link_state method is only used by mv88e6xxx_port_setup_mac(),
which is now only called during port setup, rather than also being
called via phylink's mac_config method.
Remove this now unnecessary optimisation, which allows us to remove the
port_link_state methods as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the speed independently of duplex makes little sense; the two
parameters result from negotiation or fixed setup, and may have inter-
dependencies. Moreover, they are always controlled via the same
register - having them split means we have to read-modify-write this
register twice.
Combine the two operations into a single port_set_speed_duplex()
operation. Not only is this more efficient, it reduces the size of the
code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which
handle the PCS layer of such links.
- Implement phylink PCS link state reading, so that we can provide
ethtool with the linkmodes and link speed in the expected manner.
Note: this will only be called for in-band negotiation, which is
only supported by the serdes interfaces.
- Implement phylink PCS configuration, so that the in-band AN and
advertisement can be configured.
- Implement phylink PCS negotiation restart, so that the in-band AN
can be restarted.
- Implement phylink PCS link up, so that when operating out-of-band,
the Serdes can be configured for the appropriate fixed speed mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool provides a generic mechanism for a driver to return the
registers of an ethernet device. DSA uses this to give the port
registers associated with an interfaces. Extend this to allow PCS
registers to also be returned, if the port has a PCS associated to it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.
Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 3095383a8a ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique interrupt name for the VTU and ATU,
based on the device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique g2 interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique watchdog interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:
95: 3 mv88e6xxx-g2 9 Edge mv88e6xxx-0.2:00-serdes-9
96: 0 mv88e6xxx-g2 10 Edge mv88e6xxx-0.2:00-serdes-10
The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.
It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the marvell switches have bits controlling the hash algorithm
the ATU uses for MAC addresses. In some industrial settings, where all
the devices are from the same manufacture, and hence use the same OUI,
the default hashing algorithm is not optimal. Allow the other
algorithms to be selected via devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure
a port's Layer 2 Policy Control List (PCL) via ethtool.
Currently only dropping frames based on MAC Destination or Source
Address (including the option VLAN parameter) is supported.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .port_set_policy operation to configure a port's
Policy Control List, based on mapping such as DA, SA, Etype and so on.
Models similar to 88E6352 and 88E6390 are supported at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 7a3007d22e ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").
Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.
The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many portions of the driver need to wait until a given bit is set
or cleared. Some busses even have a specific implementation for this
operation. In preparation for such variant, implement a generic Wait
Bit routine that can be used by the driver core functions.
This allows us to get rid of the custom implementations we may find
in the driver. Note that for the EEPROM bits, BUSY and RUNNING bits
are independent, thus it is more efficient to wait independently for
each bit instead of waiting for their mask.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx_wait routine is used to wait for a given mask
to be cleared to zero. However in some cases, the driver may have
to wait for a given mask to be of a certain non-zero value.
Thus provide a generic wait mask routine that will be used to implement
the current mv88e6xxx_wait function, and use it to wait for 88E6185
PPU states.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds PTP support for the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.
If a user configures an invalid port, an error is returned.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a no-op that simply moves all locking and unlocking of
->reg_lock into trivial helpers. I did that to be able to easily add
some ad hoc instrumentation to those helpers to get some information
on contention and hold times of the mutex. Perhaps others want to do
something similar at some point, so this frees them from doing the
'sed -i' yoga, and have a much smaller 'git diff' while fiddling.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell 88E6250. I've checked that each
member in the ops-structure makes sense, and basic switchdev
functionality works fine.
It uses the new dual_chip option, and since its port registers start
at SMI address 0x08 or 0x18 (i.e., always sw_addr + 0x08), we need to
introduce a new compatible string in order for the auto-identification
in mv88e6xxx_detect() to work.
The chip has four per port 16-bits statistics registers, two of which
correspond to the existing "sw_in_filtered" and "sw_out_filtered" (but
at offsets 0x13 and 0x10 rather than 0x12 and 0x13, because why should
this be easy...). Wiring up those four statistics seems to require
introducing a STATS_TYPE_PORT_6250 bit or similar, which seems a tad
ugly, so for now this just allows access to the STATS_TYPE_BANK0 ones.
The chip does have ptp support, and the existing
mv88e6352_{gpio,avb,ptp}_ops at first glance seem like they would work
out-of-the-box, but for simplicity (and lack of testing) I'm eliding
this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e6250 (as well as 6220, 6071, 6070, 6020) do not support
multi-chip (indirect) addressing. However, one can still have two of
them on the same mdio bus, since the device only uses 16 of the 32
possible addresses, either addresses 0x00-0x0F or 0x10-0x1F depending
on the ADDR4 pin at reset [since ADDR4 is internally pulled high, the
latter is the default].
In order to prepare for supporting the 88e6250 and friends, introduce
mv88e6xxx_info::dual_chip to allow having a non-zero sw_addr while
still using direct addressing.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.
Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.
[0] https://marc.info/?t=155130287200001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink wants to know when the MAC layers notices a change in the
link. For the 6390 family, this is a change in the SERDES state.
Add interrupt support for the SERDES interface used to implement
SGMII/1000Base-X/2500Base-X. This is currently limited to ports 9 and
10. Support for the 10G SERDES and other ports will be added later,
building on this basic framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An up coming change will register interrupts for individual switch
ports, using the mv88e6xxx_port as the interrupt context information.
Add members to the mv88e6xxx_port structure so we can link it back to
the mv88e6xxx_chip member the port belongs to and the port number of
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ports CMODE indicates the type of link between the MAC and the
PHY. It is used often in the SERDES code. Rather than read it each
time, cache its value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx.
TODO:
- needs to call phylink_mac_change() when the port link comes up/goes down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 can enable/disable 802.3z pause be setting the MyPause bit in
the port status register. Add an op to support this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family supports a more restricted version of hardware time
stamps. Only L2 PTP is supported. All ports have to use the same
EtherType, and transport spec configuration. PTP can only be
enabled/disabled globally, not per port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 only supports layer L2 PTP, where as the more modern devices
also support UDP and UDPv6, i.e. L4. Abstract the supported receive
filters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn