Deleted dwc2_hcd_dump_frrem() function, because it used undefined
parameters from dwc2_hsotg structure. The function body was in #ifdef
statement and was never compiled.
Also removed that parameters from dwc2_hsotg structure, which were
used only in dwc2_hcd_dump_frrem() function.
And also delete dwc2_sample_frrem macro, because without
dwc2_hcd_dump_frrem() function it's lose its purpose.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move dwc2_hsotg_wait_bit_set function to core.c so it can be used
anywhere in the code.
Added dwc2_hsotg_wait_bit_clear function in core.c.
Replace all the parts of register bit polling code with
dwc2_hsotg_wait_bit_set or dwc2_hsotg_wait_bit_clear functions
calls depends on code logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On rk3288-veyron devices on Chrome OS it was found that plugging in an
Arduino-based USB device could cause the system to lockup, especially
if the CPU Frequency was at one of the slower operating points (like
100 MHz / 200 MHz).
Upon tracing, I found that the following was happening:
* The USB device (full speed) was connected to a high speed hub and
then to the rk3288. Thus, we were dealing with split transactions,
which is all handled in software on dwc2.
* Userspace was initiating a BULK IN transfer
* When we sent the SSPLIT (to start the split transaction), we got an
ACK. Good. Then we issued the CSPLIT.
* When we sent the CSPLIT, we got back a NAK. We immediately (from
the interrupt handler) started to retry and sent another SSPLIT.
* The device kept NAKing our CSPLIT, so we kept ping-ponging between
sending a SSPLIT and a CSPLIT, each time sending from the interrupt
handler.
* The handling of the interrupts was (because of the low CPU speed and
the inefficiency of the dwc2 interrupt handler) was actually taking
_longer_ than it took the other side to send the ACK/NAK. Thus we
were _always_ in the USB interrupt routine.
* The fact that USB interrupts were always going off was preventing
other things from happening in the system. This included preventing
the system from being able to transition to a higher CPU frequency.
As I understand it, there is no requirement to retry super quickly
after a NAK, we just have to retry sometime in the future. Thus one
solution to the above is to just add a delay between getting a NAK and
retrying the transmission. If this delay is sufficiently long to get
out of the interrupt routine then the rest of the system will be able
to make forward progress. Even a 25 us delay would probably be
enough, but we'll be extra conservative and try to delay 1 ms (the
exact amount depends on HZ and the accuracy of the jiffy and how close
the current jiffy is to ticking, but could be as much as 20 ms or as
little as 1 ms).
Presumably adding a delay like this could impact the USB throughput,
so we only add the delay with repeated NAKs.
NOTE: Upon further testing of a pl2303 serial adapter, I found that
this fix may help with problems there. Specifically I found that the
pl2303 serial adapters tend to respond with a NAK when they have
nothing to say and thus we end with this same sequence.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the earlier commit dad3f793f2 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.
(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)
The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.
But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.
Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case hcd autosuspend is enabled, the hcd will enter L2 state
if no device connected. But if the controller works in otg mode, the
gadget driver still works in L0 state if connected with host. This
may result in transfer fail when gadget enqueue new request but the
hcd driver has set the global state into L2. This patch prevent the
hcd enter L2 state if the controller work in device mode.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.
Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.
So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.
With it, the gadget interface initializes properly on every
plug in.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the iomem parameters in the usb_hcd to fix this misleading
message during driver load:
dwc2 c9100000.usb: irq 22, io mem 0x00000000
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GDFIFOCFG is available from IP version 2.91a. Fix the code to reflect
this.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.
Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
commit log to be more specific about the issue]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We've seen failures when switching between host and gadget mode,
which was diagnosed as being caused due to the bus being
auto-suspended when we switched.
So this patch forces a port resume when switching to device
mode if the bus is suspended.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When removing a USB-A to USB-otg adapter cable, we get a change status
irq, and then in dwc2_conn_id_status_change, we erroneously see the
GOTGCTL_CONID_B flag set. This causes us to get stuck in the
"while (!dwc2_is_device_mode(hsotg))" loop, spitting out "Waiting for
Peripheral Mode, Mode=Host" warnings until it fails out many seconds
later.
This patch works around the issue by re-reading the GOTGCTL state to
check if the GOTGCTL_CONID_B is still set and if not restarting the
change status logic.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check these parameters only for true or false. There is no need to check
for greater or less than 0.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The otg_ver parameter only controls the SRP pulsing method and defaults
to the 1.3 behavior. It is unused and can be removed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix misaligned and over 80-character comments.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commmit is the result of running checkpatch --fix.
The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.
The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For boolean variables true/false is preferred over 1/0 for readability.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 20+ ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Uninitialized char* causes a sparse build-warning, fix it up by
initializing it to NULL.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I've found when booting HiKey with the usb gadget cable attached
if I then try to connect via adb, I get an infinite spew of:
dwc2 f72c0000.usb: dwc2_hsotg_ep_sethalt(ep ffffffc0790ecb18 ep1out, 0)
dwc2 f72c0000.usb: dwc2_hsotg_ep_sethalt(ep ffffffc0790eca18 ep1in, 0)
It seems that the usb autosuspend is suspending the bus shortly
after bootup when the gadget cable is attached. So when adbd
then tries to use the device, it doesn't work and it then tries
to restart it over and over via the ep_sethalt calls (via
FUNCTIONFS_CLEAR_HALT ioctl).
Chen Yu suggested this patch to avoid suspending if we're
in device mode, and it avoids the problem.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Suggested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removed extern specifier from dwc2_host_start(), dwc2_host_disconnect()
and dwc2_host_hub_info() functions. Moved those functions from header
to source. Then make them static.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added new core param for low speed, which can be used only when SNPSID
is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are
restricting ep types and providing to upper layer only INTR and CTRL
endpoints.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename DMA descriptor structure from dwc2_hcd_dma_desc to dwc2_dma_desc
as it is applies to both host and gadget.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because usb_pipetype() masks urb->pipe, the default case can never be
hit. Remove it. This cleans up a coverity warning.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename it so that it is more consistent with the gadget dma parameter.
It only affects host-mode operation so prefix it with "host".
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it consistent with the hw_params struct and simplifies the
memory management for future refactoring. Fix up usage in all files.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This shouldn't be freed by the HCD as it is owned by the core and
allocated with devm_kzalloc.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is safety change added while doing slub debugging.
Affected functions:
dwc2_hcd_qtd_unlink_and_free()
_dwc2_hcd_urb_enqueue()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move host core initialization and host channel routines into hcd.c. This
allows these functions to only be compiled in host-enabled driver
configurations (DRD or host-only).
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move the register save and restore functions into the host and gadget
specific files.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This totally reimplements the microframe scheduler in dwc2 to attempt to
handle periodic splits properly. The old code didn't even try, so this
was a significant effort since periodic splits are one of the most
complicated things in USB.
I've attempted to keep the old "don't use the microframe" schduler
around for now, but not sure it's needed. It has also only been lightly
tested.
I think it's pretty certain that this scheduler isn't perfect and might
have some bugs, but it seems much better than what was there before.
With this change my stressful USB test (USB webcam + USB audio + some
keyboards) crackles less.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As we start getting more exact about our scheduling it's becoming more
and more important to know exactly how far through the current frame we
are. This lets us make decisions about whether there's still time left
to start a new transaction in the current frame.
We'll add dwc2_hcd_get_future_frame_number() which will tell you what
the frame number will be a certain number of microseconds (us) from
now. We can use this information to help decide if there's enough time
left in the frame for a transaction that will take a certain duration.
This is expected to be used by a future change ("usb: dwc2: host:
Properly set even/odd frame").
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We'll use the new "scheduler verbose debugging" macro to log missed
SOFs. This is fast enough (assuming you configure it to use the ftrace
buffer) that we can do it without worrying about the speed hit. The
overhead hit if the scheduler tracing is set to "no_printk" should be
near zero.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The old code in dwc2_process_periodic_channels() would only enable the
"periodic empty" interrupt if we weren't using DMA. That wasn't right
since we can still get into cases where we have small FIFOs even on
systems that have DMA (the rk3288 is a prime example).
Let's always enable/disable the "periodic empty" when appropriate. As
part of this:
* Always call dwc2_process_periodic_channels() even if there's nothing
in periodic_sched_assigned (we move the queue empty check so we still
avoid the extra work). That will make extra certain that we will
properly disable the "periodic empty" interrupt even if there's
nothing queued up.
* Move the enable of "periodic empty" due to non-empty
periodic_sched_assigned to be for slave mode (non-DMA mode) only.
Presumably this was the original intention of the check for DMA since
it seems to match the comments above where in slave mode we leave
things on the assigned queue.
Note that even before this change slave mode didn't work for me, so I
can't say for sure that my understanding of slave mode is correct.
However, this shouldn't change anything for slave mode so if slave mode
worked for someone in the past it ought to still work.
With this change, I no longer get constant misses reported by my other
debugging code (and with future patches) when I've got:
* Rockchip rk3288 Chromebook, using port ff540000
-> Pluggable 7-port Hub with Charging (powered)
-> Microsoft Wireless Keyboard 2000 in port 1.
-> Das Keyboard in port 2.
-> Jabra Speaker in port 3
-> Logitech, Inc. Webcam C600 in port 4
-> Microsoft Sidewinder X6 Keyboard in port 5
...and I'm playing music on the USB speaker and capturing video from the
webcam.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In commit 94dfd7edfd ("USB: HCD: support giveback of URB in tasklet
context") support was added to give back the URB in tasklet context.
Let's take advantage of this in dwc2.
This speeds up the dwc2 interrupt handler considerably.
Note that this requires the change ("usb: dwc2: host: Add a delay before
releasing periodic bandwidth") to come first.
Note that, as per Alan Stern in
<https://patchwork.kernel.org/patch/7555771/>, we also need to make sure
that the extra delay before the device drivers submit more data doesn't
break the scheduler. At the moment the scheduler is pretty broken (see
future patches) so it's hard to be 100% certain, but I have yet to see
any new breakage introduced by this delay. ...and speeding up interrupt
processing for dwc2 is a huge deal because it means we've got a better
chance of not missing SOF interrupts. That means we've got an overall
win here.
Note that when playing USB audio and using a USB webcam and having
several USB keyboards plugged in, the crackling on the USB audio device
is noticably reduced with this patch.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We're supposed to keep outstanding splits in order. Keep track of a
list of the order of splits and process channel interrupts in that
order.
Without this change and the following setup:
* Rockchip rk3288 Chromebook, using port ff540000
-> Pluggable 7-port Hub with Charging (powered)
-> Microsoft Wireless Keyboard 2000 in port 1.
-> Das Keyboard in port 2.
...I find that I get dropped keys on the Microsoft keyboard (I'm sure
there are other combinations that fail, but this documents my test).
Specifically I've been typing "hahahahahahaha" on the keyboard and often
see keys dropped or repeated.
After this change the above setup works properly. This patch is based
on a previous patch proposed by Yunzhi Li ("usb: dwc2: hcd: fix periodic
transfer schedule sequence")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The queues the the dwc2 host controller used are truly queues. That
means FIFO or first in first out.
Unfortunately though the code was iterating through these queues
starting from the head, some places in the code was adding things to the
queue by adding at the head instead of the tail. That means last in
first out. Doh.
Go through and just always add to the tail.
Doing this makes things much happier when I've got:
* 7-port USB 2.0 Single-TT hub
* - Microsoft 2.4 GHz Transceiver v7.0 dongle
* - Jabra speakerphone playing music
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When poking around with USB devices with slub_debug enabled, I found
another obvious use after free. Turns out that in dwc2_hc_n_intr() I
was in a state when the contents of chan->qh was filled with 0x6b,
indicating that chan->qh was freed but chan still had a reference to
it.
Let's make sure that whenever we free qh we also make sure we remove a
reference from its channel.
The bug fixed here doesn't appear to be new--I believe I just got lucky
and happened to see it while stress testing.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
All other host controllers who want aligned buffers for DMA do it a
certain way. Let's do that too instead of working behind the USB core's
back. This makes our interrupt handler not take forever and also rips
out a lot of code, simplifying things a bunch.
This also has the side effect of removing the 65535 max transfer size
limit.
NOTE: The actual code to allocate the aligned buffers is ripped almost
completely from the tegra EHCI driver. At some point in the future we
may want to add this functionality to the USB core to share more code
everywhere.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In (usb: dwc2: reset dwc2 core before dwc2_get_hwparams()) we added an
extra reset to the probe path for the dwc2 USB controllers. This
allowed proper detection of parameters even if the firmware had already
used the USB part.
Unfortunately, this extra reset is quite slow and is affecting boot
speed. We can avoid the double-reset by skipping the extra reset that
would happen just after the one we added. Logic that explains why this
is safe:
* As of the CL mentioned above, we now always call dwc2_core_reset() in
dwc2_driver_probe() before dwc2_hcd_init().
* The only caller of dwc2_hcd_init() is dwc2_driver_probe(), so we're
guaranteed that dwc2_core_reset() was called before dwc2_hdc_init().
* dwc2_hdc_init() is the only caller that passes an irq other than -1 to
dwc2_core_init(). Thus if dwc2_core_init() is called with an irq
other than -1 we're guaranteed that dwc2_core_reset was called before
dwc2_core_init().
...this allows us to remove the dwc2_core_reset() in dwc2_core_init() if
irq is not < 0.
Note that since "irq" wasn't used in the function dwc2_core_init()
anyway and since select_phy was always set at exactly the same times we
could avoid the reset, we remove "irq" and rename "select_phy" to
"initial_setup" and adjust the callers accordingly.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function. As such no locks are already held when the
function is called.
Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks. Let's add
locks.
The bug was found by code inspection only. It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter. Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.
Specifically, the observed order is:
1. hardware sees connect
2. hardware sees disconnect
3. hardware sees connect
4. dwc2_port_intr() - clears connect interrupt
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.
We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted. We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.
Notes:
1. As part of this change we add a "force" parameter to
dwc2_hcd_disconnect() so that when we're unloading the module we
avoid the new behavior. The need for this was pointed out by John
Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
exactly the same bit of code from dwc2_port_intr(). To avoid
duplication, we refactor that code out into a new function
dwc2_hcd_connect().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Grigor Tovmasyan