Fix panic seen on some IBM and HP systems on 2.6.32-rc6:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8120bf3f>] find_next_bit+0x77/0x9c
[...]
[<ffffffff8120bbde>] cpumask_next_and+0x2e/0x3b
[<ffffffff81225c62>] pci_device_probe+0x8e/0xf5
[<ffffffff812b9be6>] ? driver_sysfs_add+0x47/0x6c
[<ffffffff812b9da5>] driver_probe_device+0xd9/0x1f9
[<ffffffff812b9f1d>] __driver_attach+0x58/0x7c
[<ffffffff812b9ec5>] ? __driver_attach+0x0/0x7c
[<ffffffff812b9298>] bus_for_each_dev+0x54/0x89
[<ffffffff812b9b4f>] driver_attach+0x19/0x1b
[<ffffffff812b97ae>] bus_add_driver+0xd3/0x23d
[<ffffffff812ba1e7>] driver_register+0x98/0x109
[<ffffffff81225ed0>] __pci_register_driver+0x63/0xd3
[<ffffffff81072776>] ? up_read+0x26/0x2a
[<ffffffffa0081000>] ? k8temp_init+0x0/0x20 [k8temp]
[<ffffffffa008101e>] k8temp_init+0x1e/0x20 [k8temp]
[<ffffffff8100a073>] do_one_initcall+0x6d/0x185
[<ffffffff8108d765>] sys_init_module+0xd3/0x236
[<ffffffff81011ac2>] system_call_fastpath+0x16/0x1b
I put in a printk and commented out the set_dev_node()
call when and got this output:
quirk_amd_nb_node: current numa_node = 0x0, would set to val & 7 = 0x0
quirk_amd_nb_node: current numa_node = 0x0, would set to val & 7 = 0x1
quirk_amd_nb_node: current numa_node = 0x0, would set to val & 7 = 0x2
quirk_amd_nb_node: current numa_node = 0x0, would set to val & 7 = 0x3
I.e. the issue appears to be that the HW has set val to a valid
value, however, the system is only configured for a single
node -- 0, the others are offline.
Check to see if the node is actually online before setting
the numa node for an AMD northbridge in quirk_amd_nb_node().
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: bhavna.sarathy@amd.com
Cc: jbarnes@virtuousgeek.org
Cc: andreas.herrmann3@amd.com
LKML-Reference: <20091112180933.12532.98685.sendpatchset@prarit.bos.redhat.com>
[ v2: clean up the code and add comments ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stanse found a pci reference leak in quirk_amd_nb_node.
Instead of putting nb_ht, there is a put of dev passed as
an argument.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The HPET in the ICH4M is not documented in the data sheet
because it was not officially validated.
While it is fine for hackers to continue to use "hpet=force"
to enable the hardware that they have, it is not prudent to
solicit additional "hpet=force" users on this hardware.
[ Impact: remove hpet=force syslog message on old-ICH systems ]
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <alpine.LFD.2.00.0904231918510.15843@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the numa_node attribute for these PCI devices is 0 (it
corresponds to the numa_node for PCI bus 0). This is not a big issue
but incorrect.
This inconsistency can be fixed by reading the node number from CPU
NB function 0.
[ Impact: fill in dev->numa_node information, to optimize DMA allocations ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: jbarnes@virtuousgeek.org
LKML-Reference: <20090417100746.GG16198@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel "Smackover" x58 BIOS don't have HPET enabled in the BIOS, so allow
to force enable it at least. The register layout is the same as in other
recent ICHs, so all the code can be reused.
Using numerical PCI-ID because it's unlikely the PCI-ID will be used
anywhere else.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: auto-enable HPET on Fujitsu u9200
HPET timer is listed in the ACPI table, but needs a quirk entry in order to
work. Unfortunately, the quirk code runs after first HPET hpet_enable() which
has already determined that the timer doesn't work (reads 0xFFFFFFFF). This
patch allows hpet_enable() to be called again after running the quirk code.
Signed-off-by: Janne Kulmala <janne.t.kulmala@tut.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This has been deprecated for years, the user space irqbalanced utility
works better with numa, has configurable policies, etc...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmai.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current quirk is incomplete. Some more chipset fiddling has to be
done to enable HPET interrupts. This patch aims to do this. From my
tests it seems to work faultlessly.
But the official statement is that HPET is not supported on SB4X0.
Users will still have to use hpet=force to enable it.
Use it at your own risk.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add PCI ID for 6300ESB force hpet
x86: add another PCI ID for ICH6 force-hpet
kernel-paramaters: document pmtmr= command line option
acpi_pm clccksource: fix printk format warning
nohz: don't stop idle tick if softirqs are pending.
pmtmr: allow command line override of ioport
nohz: reduce jiffies polling overhead
hrtimer: Remove unused variables in ktime_divns()
hrtimer: remove warning in hres_timers_resume
posix-timers: print RT watchdog message
We have a lot of HPET quirks available which might force enable HPET
even when the BIOS does not enable it. Some of those quirks depend on
the command line option "hpet=force".
Andrew pointed out that hoping that the user will find out about this
boot option is not really helpful.
Emit a kernel info which informs the user about the "hpet=force" boot
option when we enter a quirk which depends on this option and the user
did not provide it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add quirk to allow forced usage of HPET on ATI SB400.
I stumbled over machines where HPET is enabled but not reported
by BIOS. This patch configures the HPET base address and makes
it known to the OS.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this patch allows hpet=force on nVidia nForce 430 southbridge.
This patch was tested by me on my old Asus A8N-VM CSM (where bios does not
support hpet and does not advertise it via acpi entry). My nForce430 version:
lspci -nn | grep LPC
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260]
(rev a2)
Kernel 2.6.24.3 after patching and using hpet=force reports this:
dmesg | grep -i hpet
Kernel command line: root=/dev/sda8 ro vga=773 video=vesafb:mtrr:4,ywrap
vt.default_utf8=0 hpet=force
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
Time: hpet clocksource has been installed.
grep -i hpet /proc/timer_list
Clock Event Device: hpet
set_next_event: hpet_legacy_next_event
set_mode: hpet_legacy_set_mode
grep Clock /proc/timer_list (before patching)
Clock Event Device: pit
Clock Event Device: lapic
grep Clock /proc/timer_list (after patching)
Clock Event Device: hpet
Clock Event Device: lapic
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since we may not have a pci_dev for the device we need to access, we can't
use pci_read_config_word. But raw_pci_read is an internal implementation
detail; it's better to use the architected pci_bus_read_config_word
interface. Using PCI_DEVFN instead of a mysterious constant helps
reassure everyone that we really do intend to access device 8.
[ Thanks to Grant Grundler for pointing out to me that this is exactly
what the write immediately above this is doing -- enabling device 8 to
respond to config space cycles.
- Matthew
Grant also says:
"Can you also add a comment which points at the Intel
documentation?
The 'Intel E7320 Memory Controller Hub (MCH) Datasheet' at
http://download.intel.com/design/chipsets/datashts/30300702.pdf
Page 69 documents register F4h (DEVPRES1).
And I just doubled checked that the 0xf4 register value is
restored later in the quirk (obvious when you look at the code
but not from the patch"
so here it is.
- Linus ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86. Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some consumer ICH9 boards (such as the Abit IP35 Pro) do not provide a BIOS
option for enabling the HPET. The same ICH workaround used for 6,7,8 can be
applied to 9. Here I enable the only PCI id that was visible on my system.
I have confirmed the HPETs work both from userspace and as a clocksource for
the running kernel (2.6.24 here) after applying this patch.
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 64-bit timers, 14318180 Hz
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support to force_hpet for all known MCP55 (nForce 5) chipset
LPC bridges.
These are the untested nForce 5 chips (taken from Mikko's original
patch, and checked against pci.ids).
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/quirks.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
This patch adds a quirk from LinuxBIOS to force enable HPET on
the nVidia CK804 (nForce 4) chipset.
This quirk can very likely support more than just nForce 4
(LinuxBIOS use the same code for nForce 5), and possibly nForce 3,
but I don't have those chipsets, so cannot add and test them.
Tested on an Abit KN9 (CK804).
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Documentation/kernel-parameters.txt | 3 +-
arch/x86/kernel/quirks.c | 37 +++++++++++++++++++++++++++++++++++-
2 files changed, 38 insertions(+), 2 deletions(-)
ICH3 and ICH4 have undocumented HPET capabilities. This patch enables
HPET for platforms based around these ICHs.
Tested on various ICH3 and ICH4 platforms.
Because HPET is not officially documented for ICH3/4 and may not have
been validated by chipset folks, we're on thin ice here. I'd recommend
testing this patch in -hrt or -mm for a while and wait for
success/failure reports before feeding it upstream.
tglx: depends on the force_hpet command line option !
Signed-off-by: Udo A. Steinberg <us15@os.inf.tu-dresden.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds quirks to force enable HPET on Via VT8235 and
VT8237 chipsets. The datasheet for 8237 documents HPET
functionality (although wrongly) whereas HPET is undocumented
for 8235.
Tested on A7V880 (8237) and K7VT4A+ (8235) boards.
tglx: depends on the force_hept commandline option
Signed-off-by: Udo A. Steinberg <us15@os.inf.tu-dresden.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add another PCI ID for ICH7 force hpet.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
A bugfix in ich5 hpet force detect which caused resumes to fail. Thanks to
Udo A Steinberg for reporting the problem.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
force_enable hpet for ICH5.
[ Build fixes from Andrew Morton ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Force detect and/or enable HPET on ICH chipsets. This patch just handles the
detection part and following patches use this information. Adds a function to
repeat the force enabling during resume time.
Using HPET this way, instead of PIT increases the time CPUs can reside in
C-state when system is totally idle. On my test system with Core 2 Duo,
average C-state residency goes up from ~20mS to ~80mS.
[ Build fixed from Andrew Morton ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prarit Bhargava