Commit Graph

231 Commits

Author SHA1 Message Date
Inaky Perez-Gonzalez fd5c565c0c wimax/i2400m: support extended data RX protocol (no need to reallocate skbs)
Newer i2400m firmwares (>= v1.4) extend the data RX protocol so that
each packet has a 16 byte header. This header is mainly used to
implement host reordeing (which is addressed in later commits).

However, this header also allows us to overwrite it (once data has
been extracted) with an Ethernet header and deliver to the networking
stack without having to reallocate the skb (as it happened in fw <=
v1.3) to make room for it.

- control.c: indicate the device [dev_initialize()] that the driver
  wants to use the extended data RX protocol. Also involves adding the
  definition of the needed data types in include/linux/wimax/i2400m.h.

- rx.c: handle the new payload type for the extended RX data
  protocol. Prepares the skb for delivery to
  netdev.c:i2400m_net_erx().

- netdev.c: Introduce i2400m_net_erx() that adds the fake ethernet
  address to a prepared skb and delivers it to the networking
  stack.

- cleanup: in most instances in rx.c, the variable 'single' was
  renamed to 'single_last' for it better conveys its meaning.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:26 -08:00
Kay Sievers 347707baa7 wimax: struct device - replace bus_id with dev_name(), dev_set_name()
Cc: inaky.perez-gonzalez@intel.com
Cc: linux-wimax@intel.com
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:26 -08:00
Inaky Perez-Gonzalez 8987691a4a wimax/i2400m: allow control of the base-station idle mode timeout
For power saving reasons, WiMAX links can be put in idle mode while
connected after a certain time of the link not being used for tx or
rx. In this mode, the device pages the base-station regularly and when
data is ready to be transmitted, the link is revived.

This patch allows the user to control the time the device has to be
idle before it decides to go to idle mode from a sysfs
interace.

It also updates the initialization code to acknowledge the module
variable 'idle_mode_disabled' when the firmware is a newer version
(upcoming 1.4 vs 2.6.29's v1.3).

The method for setting the idle mode timeout in the older firmwares is
much more limited and can be only done at initialization time. Thus,
the sysfs file will return -ENOSYS on older ones.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:25 -08:00
Inaky Perez-Gonzalez 6a0f7ab830 wimax/i2400m: firmware_check() encodes the firmware version in i2400m->fw_version
Upcoming modifications will need to test for the running firmware
version before activating a feature or not. This is helpful to
implement backward compatibility with older firmware versions.

Modify i2400m_firmware_check() to encode in i2400m->fw_version the
major and minor version numbers of the firmware interface.

As well, move the call to be done as the very first operation once we
have communication with the device during probe() [in
__i2400m_dev_start()]. This is needed so any operation that is
executed afterwards can determine which fw version it is talking to.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:24 -08:00
Inaky Perez-Gonzalez efa05d0f0a wimax/i2400m: drop support for deprecated major fw interface, add for new minor
Firmware interface version 8.x.x has long been deprecated and is no
longer supported (nor available, as it is a preproduction firmware),
so it can be safely dropped.

Add support for firmware interface v9.2.x (current is 9.1.x). Firmware
version 9.2.x is backwards compatible with 9.1.x; new features are
enabled if switches are pressed to turn them on. Forthcoming commits
to the driver will start pressing those switches when the firmware
interface supports it.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:23 -08:00
Inaky Perez-Gonzalez 1039abbc5b wimax/i2400m: add the ability to fallback to other firmware files if the default is not there
In order to support backwards compatibility with older firmwares when
a driver is updated by a new kernel release, the i2400m bus drivers
can declare a list of firmware files they can work with (in general
these will be each a different version). The firmware loader will try
them in sequence until one loads.

Thus, if a user doesn't have the latest and greatest firmware that a
newly installed kernel would require, the driver would fall back to
the firmware from a previous release.

To support this, the i2400m->bus_fw_name is changed to be a NULL
terminated array firmware file names (and renamed to bus_fw_names) and
we add a new entry (i2400m->fw_name) that points to the name of the
firmware being currently used. All code that needs to print the
firmware file name uses i2400m->fw_name instead of the old
i2400m->bus_fw_name.

The code in i2400m_dev_bootstrap() that loads the firmware is changed
with an iterator over the firmware file name list that tries to load
each form user space, using the first one that succeeds in
request_firmware() (and thus stopping the iteration).

The USB and SDIO bus drivers are updated to take advantage of this and
reflect which firmwares they support.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:23 -08:00
Wei Yongjun c71a2699c5 i2400m: remove some pointless conditionals before kfree_skb()
Remove some pointless conditionals before kfree_skb().

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-26 23:07:31 -08:00
David S. Miller e70049b9e7 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2009-02-24 03:50:29 -08:00
Inaky Perez-Gonzalez 494ef10eba wimax/i2400m: driver loads firmware v1.4 instead of v1.3
This is a one liner change to have the driver use by default the v1.4
of the i2400m firmware instead of v1.3. The v1.4 version of the
firmware has been submitted to David Woodhouse for inclusion in the
linux-firmware tree and it is already available at
http://linuxwimax.org/Download.

The reason for this change is that the 1.3 release of the user space
software and firmware has a few issues that will make it difficult to
use with currently deployed commercial networks such as Xohm and
Clearwire.

As well, the new 1.4 release of the user space software (which matches
the 1.4 firmware) has intermitent issues with the 1.3 firmware.

The 1.4 release in http://linuxwimax.org/Download has been widely
deployed and tested with the codebase in 2.6.29-rc, the 1.4 firmware
and the 1.4 user space components.

We understand it is quite late in the rc process for such a change,
but would like to ask for the change to be taken into consideration.

Alternatively, a user could always force feed a 1.4 firmware into a
driver that doesn't have this modification by:

$ cd /lib/firmware
$ mv i2400m-fw-usb-1.3.sbcf i2400m-fw-usb-1.3.real.sbcf
$ ln -sf i2400m-fw-usb-1.4.sbc i2400m-fw-usb-1.3.sbcf

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-20 00:35:04 -08:00
Harvey Harrison ee437770c4 wimax: replace uses of __constant_{endian}
Base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 00:43:54 -08:00
David S. Miller 05bee47377 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/e1000/e1000_main.c
2009-01-30 14:31:07 -08:00
Inaky Perez-Gonzalez 1af7ad5104 wimax: fix build issue when debugfs is disabled
As reported by Toralf Förster and Randy Dunlap.

- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html

- http://lkml.org/lkml/2009/1/29/279

The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.

These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-29 17:18:31 -08:00
Inaky Perez-Gonzalez a962dc2520 wimax/i2400m: convert to net_device_ops
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:03:35 -08:00
Inaky Perez-Gonzalez f4895b8bc8 wimax/i2400m: error paths that need to free an skb should use kfree_skb()
Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.

However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.

Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19 17:58:08 -08:00
Inaky Perez-Gonzalez 9fd7a1d92b i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
Current code was assuming PM was always enabled, which is not
correct. Code which accesses members in the struct usb_device that are
dependant on CONFIG_PM must be protected the same.

Reported by Randy Dunlap from a build error in the linux-next tree on
07/01/2009.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-08 11:08:25 -08:00
Inaky Perez-Gonzalez 143ee2d555 i2400m: Makefile and Kconfig
Integrate the i2400m driver into the kernel's build and Kconfig.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez 514ec71f72 i2400m/SDIO: TX and RX path backends
Implements the backend so that the generic driver can TX/RX to/from
the SDIO device.

For RX, when data is ready the SDIO IRQ is fired and that will
allocate an skb, put all the data there and then pass it to the
generic driver RX code for processing and delivery.

TX, when kicked by the generic driver, will schedule work on a
driver-specific workqueue that pulls data from the TX FIFO and sends
it to the device until it drains it.

Thread contexts are needed as SDIO functions are blocking.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez 020bb6f30b i2400m/SDIO: firmware upload backend
This implements the backends for the generic driver (i2400m) to be
able to load firmware to the SDIO device.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez a0848826bf i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
Implements probe/disconnect for the SDIO device, as well as main
backends for the generic driver to control the SDIO device
(bus_dev_start(), bus_dev_stop() and bus_reset()).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez 17d559af96 i2400m/SDIO: header for the SDIO subdriver
This contains the common function declaration and constants for the
SDIO driver for the 2400m Wireless WiMAX Connection and it's debug
level settings.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez a8ebf98f54 i2400m/USB: TX and RX path backends
Implements the backend so that the generic driver can TX/RX to/from
the USB device.

TX is implemented with a kthread sitting in a never-ending loop that
when kicked by the generic driver's TX code will pull data from the TX
FIFO and send it to the device until it drains it. Then it goes back
sleep, waiting for another kick.

RX is implemented in a similar fashion, but reads are kicked in by the
device notifying in the interrupt endpoint that data is ready. Device
reset notifications are also sent via the notification endpoint.

We need a thread contexts to run USB autopm functions (blocking) and
to process the received data (can get to be heavy in processing
time).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez 795038107b i2400m/USB: firmware upload backend
This implements the backends for the generic driver (i2400m) to be
able to load firmware to the USB device.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez f398e4240f i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
Implements probe/disconnect for the USB device, as well as main
backends for the generic driver to control the USB device
(bus_dev_start(), bus_dev_stop() and bus_reset()).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez 11a7d0e314 i2400m/USB: header for the USB bus driver
This contains the common function declaration and constants for the
USB driver for the 2400m Wireless WiMAX Connection, as well as it's
debug level settings.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez c71228caf9 i2400m: debugfs controls
Expose knobs to control the device (induce reset, power saving,
querying tx or rx stats, internal debug information and debug level
manipulation).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:20 -08:00
Inaky Perez-Gonzalez 3a35a1d0bd i2400m: various functions for device management
This is a collection of functions used to control the device (plus a
few helpers).

There are utilities for handling TLV buffers, hooks on the device's
reports to act on device changes of state [i2400m_report_hook()], on
acks to commands [i2400m_msg_ack_hook()], a helper for sending
commands to the device and blocking until a reply arrives
[i2400m_msg_to_dev()], a few high level commands for manipulating the
device state, powersaving mode and configuration plus the routines to
setup the device once communication is established with it
[i2400m_dev_initialize()].

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:19 -08:00
Inaky Perez-Gonzalez aa5a7acabe i2400m: RX and TX data/control paths
Handling of TX/RX data to/from the i2400m device (IP packets, control
and diagnostics). On RX, this parses the received read transaction
from the device, breaks it in chunks and passes it to the
corresponding subsystems (network and control).

Transmission to the device is done through a software FIFO, as
data/control frames can be coalesced (while the device is reading the
previous tx transaction, others accumulate). A FIFO is used because at
the end it is resource-cheaper that scatter/gather over USB. As well,
most traffic is going to be download (vs upload).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:19 -08:00
Inaky Perez-Gonzalez 467cc396fb i2400m: firmware loading and bootrom initialization
Implements the firmware loader (using the bus-specific driver's
backends for the actual upload). The most critical thing in here is
the piece that puts the device in boot-mode from any other
(undetermined) state, otherwise, it is just pushing the bytes from the
firmware file to the device.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:19 -08:00
Inaky Perez-Gonzalez ce6cde9280 i2400m: linkage to the networking stack
Implementation of the glue to the network stack so the WiMAX device
shows up as an Ethernet device.

Initially we shot for implementing a Pure IP device -- however, the
world seems to turn around Ethernet devices. Main issues were with the
ISC DHCP client and servers (as they don't understand types other than
Ethernet and Token Ring).

We proceeded to register with IANA the PureIP hw type, so that DHCP
requests could declare such. We also created patches to the main ISC
DHCP versions to support it. However, until all that permeates into
deployments, there is going to be a long time.

So we moved back to wrap Ethernet frames around the PureIP device. At
the time being this has overhead; we need to reallocate with space for
an Ethernet header. The reason is the device-to-host protocol
coalesces many network packets into a single message, so we can't
introduce Ethernet headers without overwriting valid data from other
packets.

Coming-soon versions of the firmware have this issue solved.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:18 -08:00
Inaky Perez-Gonzalez 024f7f31ed i2400m: Generic probe/disconnect, reset and message passing
Implements the generic probe and disconnect functions that will be
called by the USB and SDIO driver's probe/disconnect functions.

Implements the backends for the WiMAX stack's basic operations:
message passing, rfkill control and reset.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:18 -08:00
Inaky Perez-Gonzalez ea24652d25 i2400m: host/device procotol and core driver definitions
The wimax/i2400m.h defines the structures and constants for the
host-device protocols:

 - boot / firmware upload protocol

 - general data transport protocol

 - control protocol

It is done in such a way that can also be used verbatim by user space.

drivers/net/wimax/i2400m.h defines all the APIs used by the core,
bus-generic driver (i2400m) and the bus specific drivers
(i2400m-BUSNAME). It also gives a roadmap to the driver
implementation.

debug-levels.h adds the core driver's debug settings.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:18 -08:00