Commit Graph

231 Commits

Author SHA1 Message Date
Cindy H Kao 8d8fe198c6 wimax/i2400m: don't write to memory allocated by request_firmware()
In kernel 2.6.31, the firmware requested to ram could be marked
with read only attribute, and we can't write any thing directly
to the memory when setting up the last JUMP brh cmd.

Changed so that the scratch buffer is used.

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:47 +09:00
Inaky Perez-Gonzalez 77e1251a7c wimax/i2400m: be smarter about copying command buffer to bm_cmd_buf
Because some underlying bus APIs (like USB) don't like data buffers in
the stack or vmalloced areas, the i2400m driver provides a scratch
buffer (i2400m->bm_cmd_buf) for said low-level drivers to copy command
data to before passing it to said API. This is only used during boot
mode.

However, at some the code was copying the buffer even when the command
was already specified in said buffer. This is ok, but it needs to be
more careful. As thus, change so that:

(a) the copy happens only if command buffer is not the scratch buffer

(b) use memmove() in case there is overlapping

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:46 +09:00
Cindy H Kao 339ccc362c wimax/i2400m/sdio: clear the INTR status bit after reading size
In order to avoid issues during high-load traffic, the interrupt
status register has to be cleared ONLY after the RX size is read.

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:45 +09:00
Dirk Brandewie 2093586de2 wimax/i2400m: USB driver uses a configurable endpoint map
Newer generations of the i2400m USB WiMAX device use a different
endpoint map; in order to make it easy to support it, we make the
endpoint-to-function mapeable instead of static.

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:44 +09:00
Cindy H Kao 8bec9a5efd wimax/iwmc3200: increase wait time before enable retry
When trying to enable the iwmc3200 WiMAX SDIO function, we loop
waiting for the top controller to be up and running (at which point we
can succesfully enable the function). Between each try we wait for
I2400MS_INIT_SLEEP_INTERVAL ms.

Integration tests have found the current value of 10ms to be too
short; it was upped to 100ms to give more time to the top controller
to be ready.

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:43 +09:00
Cindy H Kao 5c29e21d47 wimax/iwmc3200: don't disable the SDIO function if enable fails
In the iwmc3200, disabling the WiMAX SDIO function when enable fails
would possibly result in a device reset triggered by the iwmc3200's
top controller since it monitors the bus reset activities from each
SDIO function. In any case, the disable makes no sense; if the enable
fails, it should not be disabled.

Thus we remove the unecessary sdio_disable_func() in
i2400ms_enable_function().

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:42 +09:00
Cindy H Kao f2696fbdb6 wimax/iwmc3200: overwrite SDIO IOR timeout value to avoid platform hang
The default SDIO IOE wait timeout returned from iwmc3200-wimax's CCCR
is not efficient. This inefficiency will actually cause problems on
Moorestown platforms (system hang).

This is a sillicon bug that requires a software patch to by
overwritting func->enable_timeout. The new value I2400MS_IOR_TIMEOUT
is recommended and verified from the system integration results.

Future sillicon releases will have this default value corrected in the
future.

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:41 +09:00
Dirk Brandewie c30836580b wimax/i2400m: Make boot retries a BUS-specific parameter
In i2400m-based devices, the driver's bootloader will retry to load
the firmware when things go wrong. The driver currently has a constant
(I2400M_BOOT_RETRIES) which governs the max number of tries.

However, different SKUs of the same hardware may admit or require
different numbers of retries due to it's particulars, so it is made a
BUS specific parameter and different values are assigned for 5x50
devices versus the 3200 ones.

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:40 +09:00
Dirk Brandewie a134fd6b10 wimax/i2400m: Ensure boot mode cmd and ack buffers are alloc'd before first message
The change to the SDIO boot mode RX chain could try to use the cmd and
ack buffers befor they were allocated.  USB does not have the problem
but both were changed for consistency's sake.

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:39 +09:00
Dirk Brandewie 81b182a754 wimax/i2400m: Update comments to talk about SDIO reset and not USB.
Fixing comments from original cut and paste error

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:38 +09:00
Dan Williams abb3073383 i2400m: minimal ethtool support
Add minimal ethtool support for carrier detection.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:37 +09:00
Roel Kluin 2d44f204ad wimax: misplaced parenthesis
Fix misplaced parenthesis

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:36 +09:00
Roel Kluin a6346fa583 i2400m: keep index within ms_to_errno[]
Ensure that index `status' remains within ms_to_errno[]

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:35 +09:00
Cindy H Kao 5b45bfe501 wimax/i2400m: fix the bootmode RX deadlock in SDIO driver
i2400ms_bus_bm_wait_for_ack() causes a race condition. It happens
because this function clears i2400ms->bm_ack_size before waiting for
an interrupt, which is set by the interrupt service routine i2400ms_rx()
to indicate reception and size of received data; thus, if the interrupt
came right before the clearing/waiting, it is lost.

The fix is clear the bm_ack_size to -EINPROGRESS before we are enabling
the RX interrupt configuration in i2400ms_rx_setup(). Then everytime
when the interrupt service routine i2400ms_rx() is invoked during bootmode,
bm_ack_size is updated with the actual rx_size and it is cleared to
-EINPROGRESS again after the RX data is handled.

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:33 +09:00
Oliver Neukum 663ebb4aa2 wimax/i2400m/usb: remove unnecessary power management primitive in i2400m
This patch removes an unneeded power management primitive.
Power management is automatically enabled as probe ends.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-10-19 15:55:32 +09:00
Marcel Holtmann 384912ed19 net: Add DEVTYPE support for Ethernet based devices
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.

To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.

  # cat /sys/class/net/wlan0/uevent
  DEVTYPE=wlan
  INTERFACE=wlan0
  IFINDEX=5

This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.

The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 12:54:55 -07:00
Stephen Hemminger d0cf9c0dad wireless: convert drivers to netdev_tx_t
Mostly just simple conversions:
  * ray_cs had bogus return of NET_TX_LOCKED but driver
    was not using NETIF_F_LLTX
  * hostap and ipw2x00 had some code that returned value
    from a called function that also had to change to return netdev_tx_t

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:14:04 -07:00
Tomas Winkler 51def0bea9 imwc3200: move iwmc3200 SDIO ids to sdio_ids.h
1. add intel's sdio vendor id to sdio_ids.h
2. move iwmc3200 sdio devices' ids to sdio_ids.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-26 19:25:47 -07:00
GeunSik Lim 156f5a7801 debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.

And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.

debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/

Fix inconsistency of directory name to mount debugfs filesystem.

* From Steven Rostedt
  - find_debugfs() and tracing_files() in this patch.

Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by     : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by  : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by  : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15 21:30:28 -07:00
Inaky Perez-Gonzalez 98eb0f53e2 wimax: fix gcc warnings in sh4 when calling BUG()
SH4's BUG() seems to confuse the compiler as it is considered to
return; thus, some functions would trigger usage of uninitialized
variables or non-void functions returning void.

Work around by initializing/returning.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 11:47:39 -07:00
Cindy H Kao 0bcfc5ef01 wimax/i2400m: use -EL3RST to indicate device reset instead of -ERESTARTSYS
When the i2400m device resets, the driver code will force some
functions to return a -ERESTARTSYS error code, which can is used by
the caller to determine which recovery actions to take.

However, in certain situations the only thing that can be done is to
bubble up said error code to user space, for handling.

However, -ERESTARSYS was a poor choice, as it is supposed to be used
by the kernel only.

As such, replace -ERESTARTSYS with -EL3RST; as well, in
i2400m_msg_to_dev(), when the device is in boot mode (following a
recent reset), return -EL3RST instead of -ENODEV (meaning the device
is in bootrom mode after a reset, not that the device was
disconnected, and thus, normal commands cannot be executed).

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
2009-06-11 03:30:26 -07:00
Cindy H Kao 8b5b30ee7d wimax/i2400m: when bootstrap fails, reinitialize the bootrom
When a device reset happens during firmware load [in
i2400m_dev_bootstrap()], __i2400m_dev_start() will retry a number of
times. However, for those retries to be able to accomplish anything,
the device's bootrom has to be reinitialized.

Thus, on the retry path, pass the I2400M_MAC_REINIT to the firmware
load code.

Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
2009-06-11 03:30:26 -07:00
Inaky Perez-Gonzalez 16820c166d wimax/i2400m/sdio: Move all the RX code to a unified, IRQ based receive routine
The current SDIO code was working in polling mode for boot-mode
(firmware load) mode. This was causing issues on some hardware.

Moved all the RX code to use a unified IRQ handler that based on the
type of data the device is sending can discriminate and decide which
is the right destination.

As well, all the reads from the device are made to be at least the
block size (256); the driver will ignore the rest when not needed.

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:25 -07:00
Inaky Perez-Gonzalez 6e053d6c79 wimax/i2400m: don't reset device when bootrom init retries are exceeded
When i2400m_bootrom_init() fails to put the device into a state of
being ready to accept firmware, the driver was currently trying to
reset it if it failed to do so. This is not too useful; as part of
trying to put the device in the right state a few resets have already
been tried.

At this point, things are probably fried out and an extra reset might
do more harm than good (for example causing reseting of other
functions in the same composite device).

So it is left up to the callers to determine the error path to take
(at the end this is always i2400m_setup(), who depending on how many
retries are left, might give up on the device).

From a fix by Cindy H. Kao.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:25 -07:00
Dirk Brandewie 1c0b2dd757 wimax/i2400m/sdio: Add device specific poke table.
Add a poke table for the SDIO device (as it is different than USB).

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
2009-06-11 03:30:24 -07:00
Dirk Brandewie 7308a0c239 wimax/i2400m: move boot time poke table out of common driver
This change moves the table of "pokes" performed on the device at boot
time to the bus specific portion of the driver.

Different models of the i2400m device supported by this driver require
different poke tables, thus having a single table that works for all
is impossible. For that, the table is moved to the bus-specific
driver, who can decide which table to use based on the specifics of
the device and point the generic driver to it.

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
2009-06-11 03:30:24 -07:00
Inaky Perez-Gonzalez ecddfd5ed7 wimax/i2400m: Allow bus-specific driver to specify retry count
The code that sets up the i2400m (firmware load and general driver
setup after it) includes a couple of retry loops.

The SDIO device sometimes can get in more complicated corners than the
USB one (due to its interaction with other SDIO functions), that
require trying a few more times.

To solve that, without having a failing USB device taking longer to be
considered dead, allow the retry counts to be specified by the
bus-specific driver, which the general driver takes as a parameter.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:23 -07:00
Inaky Perez-Gonzalez b4013f91cd wimax/i2400m: if a device reboot happens during probe, handle it
When a device reboot happens when we are under probe, with init_mutex
taken, make sure we can recover. Have dev_reset_handle set boot mode
and i2400m_msg_to_dev() will see it and fail gracefully instead of
timing out.

Found and diagnosed by Cindy H. Kao.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:23 -07:00
Inaky Perez-Gonzalez 59063afa0a wimax/i2400m: fix oops when the TX FIFO fills up due to a missing check
When the TX FIFO filled up and i2400m_tx_new() failed to allocate a
new TX message header, a missing check for said condition was causing a
kernel oops when trying to dereference a NULL i2400m->tx_msg pointer.

Found and diagnosed by Cindy H. Kao.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:22 -07:00
Inaky Perez-Gonzalez b4bd07e3b1 wimax/i2400m: don't reset device on i2400m_dev_shutdown()
i2400m_dev_shutdown() tried to reset the device to put it in a known
state before shutting down.

But that turned out to be pointless. We reach this case in two paths:

 1 - when the device resets, to clean up state
 2 - when the driver is unloaded, for the same

however, in both cases it is pointless; in (1) the device is already
reset, why do it again? in (2) we can't -- the USB stack, for example,
doesn't allow communicating with the device when the driver is being
unbound and if the device is disconnected, the device is gone already.

So just remove it. Leave the function as a placeholder for future
cleanups that will be done from data allocated by the driver during
device operation.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:22 -07:00
Inaky Perez-Gonzalez 2971a5bac8 wimax/i2400m: fix panic due to missed corner cases on tail_room calculation
i2400m_tx_skip_tail() needs to handle the special case of being called
when the tail room that is left over in the FIFO is zero.

This happens when a TX message header was opened at the very end of
the FIFO (without payloads). The i2400m_tx_close() code already marked
said TX message (header) to be skipped and this function should be
doing nothing.

It is called anyway because it is part of a common "corner case" path
handling which takes care of more cases than only this one.

The tail room computation was also improved to take care of the case
when tx_in is at the end of the buffer boundary; tail_room has to be
modded (%) to the buffer size. To do that in a single well-documented
place, __i2400m_tx_tail_room() is introduced and used.

Treat i2400m->tx_in == 0 as a corner case and handle it accordingly.

Found and diagnosed by Cindy H. Kao.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:21 -07:00
Inaky Perez-Gonzalez c56affafdd wimax/i2400m: fix panic/warnings caused by missed check on empty TX message
In some situations, when a new TX message header is started, there
might be no space for data payloads. In this case the message is left
with zero payloads and the i2400m_tx_close() function has just to mark
it as "to skip". If it tries to go ahead it will overwrite things
because there is no space to add padding as defined by the
bus-specific layer. This can cause buffer overruns and in some stress
cases, panics.

Found and diagnosed by Cindy H. Kao.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:21 -07:00
Inaky Perez-Gonzalez 8593a1967f wimax/i2400m: rename misleading I2400M_PL_PAD to I2400M_PL_ALIGN
The constant is being use as an alignment factor, not as a padding
factor; made reading/reviewing the code quite confusing.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:20 -07:00
Dirk Brandewie 10b1de6b77 wimax/i2400m/sdio: Implement I2400M_RT_BUS reset type
This reset type causes the WiMAX function to be disabled and
re-enabled, which will force the WiMAX device to reset and enter boot
mode.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
2009-06-11 03:30:20 -07:00
Dirk Brandewie ead6823991 wimax/i2400m: Change d_printf() level for secure boot messages
Changing debug level of print out to support validation engineers
getting the messages they need.

Signed-off-by:  <dirk.j.brandewie@intel.com>
2009-06-11 03:30:19 -07:00
Inaky Perez-Gonzalez 16eafba8de wimax/i2400m: i2400m_schedule_work() doesn't need i2400m->work_queue
By mistake, the BUG_ON() check was left in there and it will fail when
called if i2400m->work_queue is still not setup.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:19 -07:00
Inaky Perez-Gonzalez e9a6b45be5 wimax/i2400m: i2400m's work queue should be initialized before RX support
RX support is the only user of the work-queue, to process
reports/notifications from the device. Thus, it needs the work queue
to be initialized first.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:18 -07:00
Inaky Perez-Gonzalez fff1068559 wimax/i2400m: don't call netif_start_queue() in _tx_msg_sent()
Reported and fixed by Cindy H Kao.

When the device is stopped __i2400m_dev_stop() stops the network
queue.

However, when this is done in the middle of heavy network operation,
when the bus-specific subdriver is still wrapping up and it reports a
sent TX transaction with _tx_msg_sent() right after the device was
stopped, the queue was being started again, which was causing a stream
of oopsen and finally a panic.

In any case, said call has no place there. It's a left over from an
early implementation that was discarded later on.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:18 -07:00
Inaky Perez-Gonzalez fb10167478 wimax/i2400m: introduce module parameter to disable entering power save
The i2400m driver waits for the device to report being ready for
entering power save before asking it to do so. This module parameter
allows control of said operation; if disabled, the driver won't ask
the device to enter power save mode.

This is useful in setups where power saving is not so important or
when the overhead imposed by network reentry after power save is not
acceptable; by combining this with parameter 'idle_mode_disabled', the
driver will always maintain both the connection and the device in
active state.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-06-11 03:30:17 -07:00
Inaky Perez-Gonzalez 2618ab774e wimax/i2400m: usb: fix device reset on autosuspend while not yet idle
When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.

If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.

To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is requested (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:02:27 -07:00
Inaky Perez-Gonzalez a0a4c4c9e5 wimax/i2400m: sdio: set the block size before enabling the function
From a fix by Cindy H Kao:

  Block size has to be set before sending IOE enable because the
  firmware reads the block size register before it reads IOE register.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:02:11 -07:00
Inaky Perez-Gonzalez 052991d7ac wimax/i2400m: remove redundant readiness checks from i2400m_report_tlv_*()
Functions i2400m_report_tlv*() are only called from
i2400m_report_hook(), called in a workqueue by
i2400m_report_hook_work(). The scheduler checks for device readiness
before scheduling.

Added an extra check for readiness in i2400m_report_hook_work(), which
makes all the checks down the line redundant.

Obviously the device state could change in the middle, but error
handling would take care of that.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:01:58 -07:00
Inaky Perez-Gonzalez 8ac1101f8c wimax/i2400m: factor out 'state report's TLV handling to a function
i2400m_report_state_hook() is going to get messier as we add handling
code.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:01:49 -07:00
Inaky Perez-Gonzalez 223beea238 wimax/i2400m: allow kernel commands to device to be logged too
By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user',
the driver will echo to user space all the commands being sent to the
device from user space, along with the responses.

However, this only helps with the commands being sent from user space;
with this patch, the trace hook is moved to i2400m_msg_to_dev(), which
is the single access point for running commands to the device (both by
user space and the kernel driver). This allows better debugging by
having a complete stream of commands/acks and reports.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:01:42 -07:00
Inaky Perez-Gonzalez 44b849d11b wimax/i2400m: trace commands sent from user space on the "echo" pipe
When commands are sent from user space, trace both the command sent
and the answer received over the "echo" pipe instead of over the
"trace" pipe when command tracing is enabled. As well, when the device
sends a reports/indications, send it over the "echo" pipe.

The "trace" pipe is used by the device to send firmware traces;
gets confusing. Another named pipe makes it easier to split debug
information.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:01:35 -07:00
Inaky Perez-Gonzalez fe44268385 wimax/i2400m: generate fake source MAC address with random_ether_addr()
The WiMAX i2400m driver needs to generate a fake source MAC address to
fake an ethernet header (for destination, the card's MAC is
used). This is the source of the packet, which is the basestation it
came from. The basestation's mac address is not usable for this, as it
uses its own namespace and it is not always available.

Currently the fake source MAC address was being set to all zeros,
which was causing trouble with bridging.

Use random_ether_addr() to generate a proper one that creates no
trouble.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-28 18:01:24 -07:00
Inaky Perez-Gonzalez 4e5b6d006b wimax/i2400m: fix device crash: fix optimization in _roq_queue_update_ws
When the i2400m receives data and the device indicates there has to be
reordering, we keep an sliding window implementation to sort the
packets before sending them to the network stack.

One of the "operations" that the device indicates is "queue a packet
and update the window start". When the queue is empty, this is
equivalent to "deliver the packet and update the window start".

That case was optimized in i2400m_roq_queue_update_ws() so that we
would not pointlessly queue and dequeue a packet. However, when the
optimization was active, it wasn't updating the window start. That
caused the reorder management code to get confused later on with what
seemed to be wrong reorder requests from the device.

Thus the fix implemented is to do the right thing and update the
window start in both cases, when the queue is empty (and the
optimization is done) and when not.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2009-05-14 18:00:32 -07:00
Randy Dunlap ff5e2b4732 wimax: fix i2400m printk formats
Fix printk format warnings:

drivers/net/wimax/i2400m/netdev.c:523: warning: format '%zu' expects type 'size_t', but argument 7 has type 'unsigned int'
drivers/net/wimax/i2400m/netdev.c:548: warning: format '%zu' expects type 'size_t', but argument 7 has type 'unsigned int'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-11 23:24:03 -07:00
Inaky Perez-Gonzalez c747583d19 wimax/i2400m: implement RX reorder support
Allow the device to give the driver RX data with reorder information.

When that is done, the device will indicate the driver if a packet has
to be held in a (sorted) queue. It will also tell the driver when held
packets have to be released to the OS.

This is done to improve the WiMAX-protocol level retransmission
support when missing frames are detected.

The code docs provide details about the implementation.

In general, this just hooks into the RX path in rx.c; if a packet with
the reorder bit in the RX header is detected, the reorder information
in the header is extracted and one of the four main reorder operations
are executed. In one case (queue) no packet will be delivered to the
networking stack, just queued, whereas in the others (reset, update_ws
and queue_update_ws), queued packet might be delivered depending on
the window start for the specific queue.

The modifications to files other than rx.c are:

- control.c: during device initialization, enable reordering support
  if the rx_reorder_disabled module parameter is not enabled

- driver.c: expose a rx_reorder_disable module parameter and call
  i2400m_rx_setup/release() to initialize/shutdown RX reorder
  support.

- i2400m.h: introduce members in 'struct i2400m' needed for
  implementing reorder support.

- linux/i2400m.h: introduce TLVs, commands and constant definitions
  related to RX reorder

Last but not least, the rx reorder code includes an small circular log
where the last N reorder operations are recorded to be displayed in
case of inconsistency. Otherwise diagnosing issues would be almost
impossible.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:28 -08:00
Harvey Harrison 61b8d2688a wimax: replace uses of __constant_{endian}
Base versions handle constant folding now.

Edited by Inaky to fix conflicts due to changes in netdev.c

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:27 -08:00
Inaky Perez-Gonzalez fd5c565c0c wimax/i2400m: support extended data RX protocol (no need to reallocate skbs)
Newer i2400m firmwares (>= v1.4) extend the data RX protocol so that
each packet has a 16 byte header. This header is mainly used to
implement host reordeing (which is addressed in later commits).

However, this header also allows us to overwrite it (once data has
been extracted) with an Ethernet header and deliver to the networking
stack without having to reallocate the skb (as it happened in fw <=
v1.3) to make room for it.

- control.c: indicate the device [dev_initialize()] that the driver
  wants to use the extended data RX protocol. Also involves adding the
  definition of the needed data types in include/linux/wimax/i2400m.h.

- rx.c: handle the new payload type for the extended RX data
  protocol. Prepares the skb for delivery to
  netdev.c:i2400m_net_erx().

- netdev.c: Introduce i2400m_net_erx() that adds the fake ethernet
  address to a prepared skb and delivers it to the networking
  stack.

- cleanup: in most instances in rx.c, the variable 'single' was
  renamed to 'single_last' for it better conveys its meaning.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:26 -08:00
Kay Sievers 347707baa7 wimax: struct device - replace bus_id with dev_name(), dev_set_name()
Cc: inaky.perez-gonzalez@intel.com
Cc: linux-wimax@intel.com
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:26 -08:00
Inaky Perez-Gonzalez 8987691a4a wimax/i2400m: allow control of the base-station idle mode timeout
For power saving reasons, WiMAX links can be put in idle mode while
connected after a certain time of the link not being used for tx or
rx. In this mode, the device pages the base-station regularly and when
data is ready to be transmitted, the link is revived.

This patch allows the user to control the time the device has to be
idle before it decides to go to idle mode from a sysfs
interace.

It also updates the initialization code to acknowledge the module
variable 'idle_mode_disabled' when the firmware is a newer version
(upcoming 1.4 vs 2.6.29's v1.3).

The method for setting the idle mode timeout in the older firmwares is
much more limited and can be only done at initialization time. Thus,
the sysfs file will return -ENOSYS on older ones.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:25 -08:00
Inaky Perez-Gonzalez 6a0f7ab830 wimax/i2400m: firmware_check() encodes the firmware version in i2400m->fw_version
Upcoming modifications will need to test for the running firmware
version before activating a feature or not. This is helpful to
implement backward compatibility with older firmware versions.

Modify i2400m_firmware_check() to encode in i2400m->fw_version the
major and minor version numbers of the firmware interface.

As well, move the call to be done as the very first operation once we
have communication with the device during probe() [in
__i2400m_dev_start()]. This is needed so any operation that is
executed afterwards can determine which fw version it is talking to.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:24 -08:00
Inaky Perez-Gonzalez efa05d0f0a wimax/i2400m: drop support for deprecated major fw interface, add for new minor
Firmware interface version 8.x.x has long been deprecated and is no
longer supported (nor available, as it is a preproduction firmware),
so it can be safely dropped.

Add support for firmware interface v9.2.x (current is 9.1.x). Firmware
version 9.2.x is backwards compatible with 9.1.x; new features are
enabled if switches are pressed to turn them on. Forthcoming commits
to the driver will start pressing those switches when the firmware
interface supports it.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:23 -08:00
Inaky Perez-Gonzalez 1039abbc5b wimax/i2400m: add the ability to fallback to other firmware files if the default is not there
In order to support backwards compatibility with older firmwares when
a driver is updated by a new kernel release, the i2400m bus drivers
can declare a list of firmware files they can work with (in general
these will be each a different version). The firmware loader will try
them in sequence until one loads.

Thus, if a user doesn't have the latest and greatest firmware that a
newly installed kernel would require, the driver would fall back to
the firmware from a previous release.

To support this, the i2400m->bus_fw_name is changed to be a NULL
terminated array firmware file names (and renamed to bus_fw_names) and
we add a new entry (i2400m->fw_name) that points to the name of the
firmware being currently used. All code that needs to print the
firmware file name uses i2400m->fw_name instead of the old
i2400m->bus_fw_name.

The code in i2400m_dev_bootstrap() that loads the firmware is changed
with an iterator over the firmware file name list that tries to load
each form user space, using the first one that succeeds in
request_firmware() (and thus stopping the iteration).

The USB and SDIO bus drivers are updated to take advantage of this and
reflect which firmwares they support.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 03:10:23 -08:00
Wei Yongjun c71a2699c5 i2400m: remove some pointless conditionals before kfree_skb()
Remove some pointless conditionals before kfree_skb().

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-26 23:07:31 -08:00
David S. Miller e70049b9e7 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2009-02-24 03:50:29 -08:00
Inaky Perez-Gonzalez 494ef10eba wimax/i2400m: driver loads firmware v1.4 instead of v1.3
This is a one liner change to have the driver use by default the v1.4
of the i2400m firmware instead of v1.3. The v1.4 version of the
firmware has been submitted to David Woodhouse for inclusion in the
linux-firmware tree and it is already available at
http://linuxwimax.org/Download.

The reason for this change is that the 1.3 release of the user space
software and firmware has a few issues that will make it difficult to
use with currently deployed commercial networks such as Xohm and
Clearwire.

As well, the new 1.4 release of the user space software (which matches
the 1.4 firmware) has intermitent issues with the 1.3 firmware.

The 1.4 release in http://linuxwimax.org/Download has been widely
deployed and tested with the codebase in 2.6.29-rc, the 1.4 firmware
and the 1.4 user space components.

We understand it is quite late in the rc process for such a change,
but would like to ask for the change to be taken into consideration.

Alternatively, a user could always force feed a 1.4 firmware into a
driver that doesn't have this modification by:

$ cd /lib/firmware
$ mv i2400m-fw-usb-1.3.sbcf i2400m-fw-usb-1.3.real.sbcf
$ ln -sf i2400m-fw-usb-1.4.sbc i2400m-fw-usb-1.3.sbcf

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-20 00:35:04 -08:00
Harvey Harrison ee437770c4 wimax: replace uses of __constant_{endian}
Base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 00:43:54 -08:00
David S. Miller 05bee47377 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/e1000/e1000_main.c
2009-01-30 14:31:07 -08:00
Inaky Perez-Gonzalez 1af7ad5104 wimax: fix build issue when debugfs is disabled
As reported by Toralf Förster and Randy Dunlap.

- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html

- http://lkml.org/lkml/2009/1/29/279

The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.

These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-29 17:18:31 -08:00
Inaky Perez-Gonzalez a962dc2520 wimax/i2400m: convert to net_device_ops
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:03:35 -08:00
Inaky Perez-Gonzalez f4895b8bc8 wimax/i2400m: error paths that need to free an skb should use kfree_skb()
Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.

However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.

Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19 17:58:08 -08:00
Inaky Perez-Gonzalez 9fd7a1d92b i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
Current code was assuming PM was always enabled, which is not
correct. Code which accesses members in the struct usb_device that are
dependant on CONFIG_PM must be protected the same.

Reported by Randy Dunlap from a build error in the linux-next tree on
07/01/2009.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-08 11:08:25 -08:00
Inaky Perez-Gonzalez 143ee2d555 i2400m: Makefile and Kconfig
Integrate the i2400m driver into the kernel's build and Kconfig.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez 514ec71f72 i2400m/SDIO: TX and RX path backends
Implements the backend so that the generic driver can TX/RX to/from
the SDIO device.

For RX, when data is ready the SDIO IRQ is fired and that will
allocate an skb, put all the data there and then pass it to the
generic driver RX code for processing and delivery.

TX, when kicked by the generic driver, will schedule work on a
driver-specific workqueue that pulls data from the TX FIFO and sends
it to the device until it drains it.

Thread contexts are needed as SDIO functions are blocking.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez 020bb6f30b i2400m/SDIO: firmware upload backend
This implements the backends for the generic driver (i2400m) to be
able to load firmware to the SDIO device.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez a0848826bf i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
Implements probe/disconnect for the SDIO device, as well as main
backends for the generic driver to control the SDIO device
(bus_dev_start(), bus_dev_stop() and bus_reset()).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez 17d559af96 i2400m/SDIO: header for the SDIO subdriver
This contains the common function declaration and constants for the
SDIO driver for the 2400m Wireless WiMAX Connection and it's debug
level settings.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:22 -08:00
Inaky Perez-Gonzalez a8ebf98f54 i2400m/USB: TX and RX path backends
Implements the backend so that the generic driver can TX/RX to/from
the USB device.

TX is implemented with a kthread sitting in a never-ending loop that
when kicked by the generic driver's TX code will pull data from the TX
FIFO and send it to the device until it drains it. Then it goes back
sleep, waiting for another kick.

RX is implemented in a similar fashion, but reads are kicked in by the
device notifying in the interrupt endpoint that data is ready. Device
reset notifications are also sent via the notification endpoint.

We need a thread contexts to run USB autopm functions (blocking) and
to process the received data (can get to be heavy in processing
time).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez 795038107b i2400m/USB: firmware upload backend
This implements the backends for the generic driver (i2400m) to be
able to load firmware to the USB device.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez f398e4240f i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
Implements probe/disconnect for the USB device, as well as main
backends for the generic driver to control the USB device
(bus_dev_start(), bus_dev_stop() and bus_reset()).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez 11a7d0e314 i2400m/USB: header for the USB bus driver
This contains the common function declaration and constants for the
USB driver for the 2400m Wireless WiMAX Connection, as well as it's
debug level settings.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:21 -08:00
Inaky Perez-Gonzalez c71228caf9 i2400m: debugfs controls
Expose knobs to control the device (induce reset, power saving,
querying tx or rx stats, internal debug information and debug level
manipulation).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:20 -08:00
Inaky Perez-Gonzalez 3a35a1d0bd i2400m: various functions for device management
This is a collection of functions used to control the device (plus a
few helpers).

There are utilities for handling TLV buffers, hooks on the device's
reports to act on device changes of state [i2400m_report_hook()], on
acks to commands [i2400m_msg_ack_hook()], a helper for sending
commands to the device and blocking until a reply arrives
[i2400m_msg_to_dev()], a few high level commands for manipulating the
device state, powersaving mode and configuration plus the routines to
setup the device once communication is established with it
[i2400m_dev_initialize()].

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:19 -08:00
Inaky Perez-Gonzalez aa5a7acabe i2400m: RX and TX data/control paths
Handling of TX/RX data to/from the i2400m device (IP packets, control
and diagnostics). On RX, this parses the received read transaction
from the device, breaks it in chunks and passes it to the
corresponding subsystems (network and control).

Transmission to the device is done through a software FIFO, as
data/control frames can be coalesced (while the device is reading the
previous tx transaction, others accumulate). A FIFO is used because at
the end it is resource-cheaper that scatter/gather over USB. As well,
most traffic is going to be download (vs upload).

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:19 -08:00
Inaky Perez-Gonzalez 467cc396fb i2400m: firmware loading and bootrom initialization
Implements the firmware loader (using the bus-specific driver's
backends for the actual upload). The most critical thing in here is
the piece that puts the device in boot-mode from any other
(undetermined) state, otherwise, it is just pushing the bytes from the
firmware file to the device.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:19 -08:00
Inaky Perez-Gonzalez ce6cde9280 i2400m: linkage to the networking stack
Implementation of the glue to the network stack so the WiMAX device
shows up as an Ethernet device.

Initially we shot for implementing a Pure IP device -- however, the
world seems to turn around Ethernet devices. Main issues were with the
ISC DHCP client and servers (as they don't understand types other than
Ethernet and Token Ring).

We proceeded to register with IANA the PureIP hw type, so that DHCP
requests could declare such. We also created patches to the main ISC
DHCP versions to support it. However, until all that permeates into
deployments, there is going to be a long time.

So we moved back to wrap Ethernet frames around the PureIP device. At
the time being this has overhead; we need to reallocate with space for
an Ethernet header. The reason is the device-to-host protocol
coalesces many network packets into a single message, so we can't
introduce Ethernet headers without overwriting valid data from other
packets.

Coming-soon versions of the firmware have this issue solved.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:18 -08:00
Inaky Perez-Gonzalez 024f7f31ed i2400m: Generic probe/disconnect, reset and message passing
Implements the generic probe and disconnect functions that will be
called by the USB and SDIO driver's probe/disconnect functions.

Implements the backends for the WiMAX stack's basic operations:
message passing, rfkill control and reset.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:18 -08:00
Inaky Perez-Gonzalez ea24652d25 i2400m: host/device procotol and core driver definitions
The wimax/i2400m.h defines the structures and constants for the
host-device protocols:

 - boot / firmware upload protocol

 - general data transport protocol

 - control protocol

It is done in such a way that can also be used verbatim by user space.

drivers/net/wimax/i2400m.h defines all the APIs used by the core,
bus-generic driver (i2400m) and the bus specific drivers
(i2400m-BUSNAME). It also gives a roadmap to the driver
implementation.

debug-levels.h adds the core driver's debug settings.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:18 -08:00