As defined in PAPR 2.4, Partitionable Endpoint (PE) is an I/O subtree
that can be treated as a unit for the purposes of partitioning and error
recovery. Therefore, eeh core should be aware of PE. With eeh_pe struct,
we can support PE explicitly. Further more, it makes all the stuff much
more data centralized. Another important reason is for eeh core to support
multiple platforms. Some of them like pSeries figures out PEs through
OF nodes while others like powernv have to do that through PCI bus/device
tree. With explicit PE support, eeh core will be implemented based on
the centrialized data and platform dependent implementations figure it
out by their feasible ways.
When the struct is designed, following factors are taken in account:
* Reflecting the relationships of PEs. PE might have parent
as well children.
* Reflecting the association of PE and (eeh) devices.
* PEs have PHB boundary.
* PE should have unique address assigned in the corresponding
PHB domain.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds more logs to EEH initialization functions for
debugging purpose. Also, the machine type (pSeries) is checked
in the platform initialization to assure it's the correct platform
to invoke it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH initialization functions have been postponed until slab/slub
are ready. So we use slab/slub to allocate the memory chunks for newly
creatd EEH devices. That would save lots of memory.
The patch also does cleanup to replace "kmalloc" with "kzalloc" so
that we needn't clear the allocated memory chunk explicitly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we have 3 phases for EEH initialization on pSeries platform.
All of them are done through builtin functions: platform initialization,
EEH device creation, and EEH subsystem enablement. All of them are done
no later than ppc_md.setup_arch. That means that the slab/slub isn't ready
yet, so we have to allocate memory chunks on basis of PAGE_SIZE for those
dynamically created EEH devices. That's pretty expensive.
In order to utilize slab/slub for memory allocation, we have to move the EEH
initialization functions around, but all of them should be called after slab
is ready.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's possible for the cpu_possible_mask to change between the time we
initialise the pacas and the time we setup per_cpu areas.
Obviously impossible cpus shouldn't ever be running, but stranger things
have happened. So be paranoid and initialise data_offset with a poison
value in case we don't set it up later.
Based on a patch from Anton Blanchard.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In powerpc randconfig builds, this keeps showing up:
CC arch/powerpc/platforms/512x/mpc512x_shared.o
arch/powerpc/platforms/512x/mpc512x_shared.c:70:9: warning: 'enum fsl_diu_monitor_port' declared inside parameter list
arch/powerpc/platforms/512x/mpc512x_shared.c:70:9: warning: its scope is only this definition or declaration, which is probably not what you want
arch/powerpc/platforms/512x/mpc512x_shared.c:69:56: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:69:5: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c:84:9: warning: 'enum fsl_diu_monitor_port' declared inside parameter list
arch/powerpc/platforms/512x/mpc512x_shared.c:83:56: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:83:6: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c:88:36: warning: 'enum fsl_diu_monitor_port' declared inside parameter list
arch/powerpc/platforms/512x/mpc512x_shared.c:88:57: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:88:6: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c:187:54: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:187:1: error: return type is an incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:187:1: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c: In function 'mpc512x_valid_monitor_port':
arch/powerpc/platforms/512x/mpc512x_shared.c:189:9: error: 'FSL_DIU_PORT_DVI' undeclared (first use in this function)
arch/powerpc/platforms/512x/mpc512x_shared.c:189:9: note: each undeclared identifier is reported only once for each function it appears in
arch/powerpc/platforms/512x/mpc512x_shared.c:189:2: warning: 'return' with a value, in function returning void
make[2]: *** [arch/powerpc/platforms/512x/mpc512x_shared.o] Error 1
The reason is that mpc512x_shared.c has a couple token #ifdef
on FB_FSL_DIU/FB_FSL_DIU_MODULE, but they don't come close to
masking all the DIU dependencies, as the above fail shows.
Rather than sprinkle more pointless #ifdef in this file, just
remove the existing two, and make FB_FSL_DIU part of the
dependency. The mpc512x_defconfig already has the line
"CONFIG_FB_FSL_DIU=y" so this change should be zero impact
on real world configs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
c1dcad2d32 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We never use the XDABR hcall since we check for DABR hcall first.
XDABR syscall is better since it allows us to also set the DABRX.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change bp_info to info to be consistent with the rest of this file.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc kernel doesn't export the memory limit enforced by 'mem='
kernel parameter. This is required for building the ELF header in
kexec-tools to limit the vmcore to capture only the used memory. On
powerpc the kexec-tools depends on the device-tree for memory related
information, unlike /proc/iomem on the x86.
Without this information, the kexec-tools assumes the entire System
RAM and vmcore creates an unnecessarily larger dump.
This patch exports the memory limit, if present, via
chosen/linux,memory-limit
property, so that the vmcore can be limited to the memory limit.
The prom_init seems to export this value in the same node. But doesn't
really
appear there. Also the memory_limit gets adjusted with the processing of
crashkernel= parameter. This patch makes sure we get the actual limit.
The kexec-tools will use the value to limit the 'end' of the memory
regions.
Tested this patch on ppc64 and ppc32(ppc440) with a kexec-tools
patch by Mahesh.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Tested-by: Mahesh J. Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are some device-tree nodes, whose values are of type phys_addr_t.
The phys_addr_t is variable sized based on the CONFIG_PHSY_T_64BIT.
Change these to a fixed unsigned long long for consistency.
This patch does the change only for memory_limit.
The following is a list of such variables which need the change:
1) kernel_end, crashk_size - in arch/powerpc/kernel/machine_kexec.c
2) (struct resource *)crashk_res.start - We could export a local static
variable from machine_kexec.c.
Changing the above values might break the kexec-tools. So, I will
fix kexec-tools first to handle the different sized values and then change
the above.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several files in obj-plat depend on libfdt header file. Sometimes
when building one can see the following issue. This patch adds
libfdt as dependency to those object files
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:854:1: error: unterminated comment
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:1:0: error: unterminated #ifndef
| BOOTCC arch/powerpc/boot/inffast.o
| make[1]: *** [arch/powerpc/boot/treeboot-iss4xx.o] Error 1
| make[1]: *** Waiting for unfinished jobs....
| BOOTCC arch/powerpc/boot/inflate.o
| make: *** [uImage] Error 2
| ERROR: oe_runmake failed
| ERROR: Function failed: do_compile (see /srv/home/pokybuild/yocto-autobuilder/yocto-slave/p1022ds/build/build/tmp/work/p1022ds-poky-linux-gnuspe/linux-qoriq-sdk-3.0.34-r5/temp/log.do_compile.2167 for further information)
NOTE: recipe linux-qoriq-sdk-3.0.34-r5: task do_compile: Failed
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Starting with Power 7+ we need to check for marked events if the SIAR
register is valid, i.e. it contains the correct address of the instruction
at the time the performance counter overflowed. The mmcra register on
Power 7+, contains a new bit to indicate that the contents of the SIAR
is valid. If the event is not marked, then the sample is recorded
independently of the SIAR valid bit setting. For older processors, there
is no SIAR valid bit to check so the samples are always recorded. This is
done by forcing the cntr_marked_events bit mask to zero. The code will
always record the sample in this case since the bit mask says the event is
not a marked event even if it really is a marked event.
Signed-off-by: Carl Love <cel@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This definition will be used by subsequent perf and oprofile patches
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pseries firmware currently refuses any non power of two MSI-X
request. Unfortunately most network drivers end up asking for that
because they want a power of two for RX queues and one or two extra
for everything else.
This patch rounds up the firmware request to the next power of two
if the quota allows it. If this fails we fall back to using the
original request size.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI probe flag PCI_REASSIGN_ALL_RSRC has been passed into PCI
core, it's hoped that all resources to be reassigned by PCI core.
As to particular P2P (PCI-to-PCI) bridge, the size of the corresponding
BAR (I/O, MMIO, prefetchable MMIO) is calculated by the resources
required by the PCI devices behind the P2P bridge. That means that
the information like start/end address retrieved from the hardware
registers of the P2P bridge is meainingless in the case. However,
we still count that in and the BARs might have been configured by
firmware with non-zero size. That leads to space waste.
The patch explicitly sets the size of P2P bridge BARs to zero in
case that resource reassignment is expected with PCI probe flag
PCI_REASSIGN_ALL_RSRC. In the result, it will save overall resource
required by the system without waste.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQSS7TAAoJEFjIrFwIi8fJOBQH/03JBKBbFvewhop8T5Jww2c9
SWmMgzDm5HkxeWj5XnM+zlLoHrYFFu7tyuRLiny4weE0LdRl4adJ1TVpStxap/b6
MSQKe+tZevslaReBOsMpbCk3z7fEWNlAcpm6wMp1xYmLoHcr0JMpOCmzigbf7dwM
F4UWULheih9ME3UeqDAU8qgvfv6ccZ9vempO4TDWKjxfxfWODCNMRx+Ny+C7NNRk
QeoInHJUqcRkg0q0OIciF/YYDmn8hIH7HgfqomuMb6rEv2LOieLnWVuniEPWM75s
lECxro7v2Z9s1Std0WWKcFp8VZpI2scnQYU8aL8TpewHcbzKHQYyipuKPu7FiEQ=
=GfLE
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zFNa
-----END PGP SIGNATURE-----
Merge tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
commit: 8b7b80b9eb
[24/29] powerpc: Uprobes port to powerpc
Caused a clash with the fore200e driver:
In file included from drivers/atm/fore200e.c:70:0:
drivers/atm/fore200e.h:263:3: error: redefinition of typedef 'opcode_t' with different type
arch/powerpc/include/asm/probes.h:25:13: note: previous declaration of 'opcode_t' was here
Fix the namespace clash by making opcode_t in probes.h to ppc_opcode_t.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Critical exception on 64-bit booke uses user-visible SPRG3 as scratch.
Restore VDSO information in SPRG3 on exception prolog.
Use a common sprg3 field in PACA for all powerpc64 architectures.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hMrY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eZQ4
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.
While the changes are not in the drivers/hwmon directory, the problem
primarily affects hwmon drivers, and it makes sense to push the patch
through the hwmon tree."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends
Pull kbuild fixes from Michal Marek:
"These are two fixes that should go into 3.6. The link-vmlinux.sh one
is obvious.
The other one fixes make firmware_install with certain configurations,
where a file in the toplevel firmware tree gets installed first, and
$(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
confuses make 3.82 for some reason."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
firmware: fix directory creation rule matching with make 3.82
link-vmlinux.sh: Fix stray "echo" in error message
When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:
> lspci -s 04:00.0
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
13:42:12 # 4 :~/
> echo "0000:04:00.0" > /sys/bus/pci/drivers/pciback/unbind
> modprobe e1000e
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:04:00.0: Disabling ASPM L0s L1
e1000e 0000:04:00.0: enabling device (0000 -> 0002)
xen: registering gsi 48 triggering 0 polarity 1
Already setup the GSI :48
e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e: probe of 0000:04:00.0 failed with error -2
This fixes it by first saving the PCI configuration space, then
doing the FLR.
Reported-by: Ren, Yongjie <yongjie.ren@intel.com>
Reported-and-Tested-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQR/7BAAoJEHNBYZ7TNxYMT3gQANQDdD/wvYFgUvssIAgdQJdl
KORu7ke5ks2Gvx0Ef0Ch+GXIFFDoqH0zMkQMXc+c0BdhR4BF/vNBbBYZoVYyvmgK
GUHK740nznwp9edIVbGbRm+FSxDG7ZpjUlFq+SInBOehIw7tQAep3Tbv1rYZzu6M
SUBGc31Nif9eCvTKzGU195qbutAhvcGmqEvi/ALP9bUCYR7QaTt/oD3YYuUD/ZjV
O/mf3R30vrV+R1lrQRqzXIi8vCojPMzkVU8x+C8PdOTjewvYviM0huW9+Lv6WsxK
DzhCgoNvrB1Q/rYtiNZ1gyWd5cTZWns308slREEwywD5IBQJMo5T68Q/D+h2PkS9
JCvtiZ+ryycvINyUn2JxEZuygseUiT/nMS0ijSidQY7vrZlNR8JrrK3qf0vRDkWo
0mXhQG5DvxDN6Dx9K15OgTAuABek1CEdKFD0R/a3X41H/KUvKQwWPWmdTybBriAo
8jkUl64YMpFt+LZqrmeQ1oOcwc8BvMvcM4dnMbkXrHvBb926fENBIMGNeI7O10o8
597dEpLlKNZj8e8YxJjbqaCuFhOp/pHRQy+rxdjP28V4mfHASQGgsnFAO4qV7B24
1wqtSu5ZCor4K616wfDvMYgL88pMg7fVEV3nN9Cc/WpsBaBPZv7vOQbp/f40rKWa
GRb9+9NC0WU0CP28GlCq
=n1hi
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: omap: fix broken PIO mode
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
mmc: dw_mmc: fix error handling in PIO mode
mmc: dw_mmc: correct mishandling error interrupt
mmc: dw_mmc: amend using error interrupt status
mmc: atmel-mci: not busy flag has also to be used for read operations
mmc: sdhci-esdhc: break out early if clock is 0
mmc: mxs-mmc: fix deadlock caused by recursion loop
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
mmc: bfin_sdh: fix dma_desc_array build error
Fix the following compile error on UML.
arch/um/os-Linux/time.c: In function 'deliver_alarm':
arch/um/os-Linux/time.c:117:3: error: too few arguments to function 'alarm_handler'
arch/um/os-Linux/internal.h:1:6: note: declared here
The error was introduced by commit d3c1cfcd ("um: pass siginfo to guest
process") in 3.6-rc1.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Martin Pärtel <martin.partel@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allocate a structure not a pointer to it !
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for 3.6 that were piling up while I was away or
busy (I was mostly MIA a week or two before San Diego).
Some fixes from Anton fixing up issues with our relatively new DSCR
control feature, and a few other fixes that are either regressions or
bugs nasty enough to warrant not waiting."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being
compiled in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma
Mobile GPIO driver.
- Assign the owner field for the rdc321x driver so the
module won't be removed if it has active GPIOs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QDOR
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"These are some GPIO regression fixes for v3.6:
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being compiled
in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma Mobile GPIO
driver.
- Assign the owner field for the rdc321x driver so the module won't
be removed if it has active GPIOs."
* tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rdc321x: Prevent removal of modules exporting active GPIOs
gpio: em: Fix checking return value of irq_alloc_descs
gpio: mc9s08dz60: Fix build error if I2C=m
gpio: Fix debug message in of_get_named_gpio_flags()
There are nothing scaring, contains only small fixes for HD-audio and
USB-audio:
- EPSS regression fix and GPIO fix for HD-audio IDT codecs
- A series of USB-audio regression fixes that are found since 3.5 kernel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=AbfN
-----END PGP SIGNATURE-----
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There are nothing scaring, contains only small fixes for HD-audio and
USB-audio:
- EPSS regression fix and GPIO fix for HD-audio IDT codecs
- A series of USB-audio regression fixes that are found since 3.5
kernel"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb: fix cross-interface streaming devices
ALSA: snd-usb: fix calls to next_packet_size
ALSA: snd-usb: restore delay information
ALSA: snd-usb: use list_for_each_safe for endpoint resources
ALSA: snd-usb: Fix URB cancellation at stream start
ALSA: hda - Don't trust codec EPSS bit for IDT 92HD83xx & co
ALSA: hda - Avoid unnecessary parameter read for EPSS
ALSA: hda - Do not set GPIOs for speakers on IDT if there are no speakers
- a fix by Paul Cercueil to prevent a possible buffer overflow
- a fix by Bruno Prémont to prevent a rare sleep in invalid context
- a fix by Julia Lawall for a double free in auo_k190x
- a fix by Dan Carpenter to prevent a division by zero in mb862xxfb
- a regression fix by Tomi Valkeinen for the SDI output in OMAP
- a fix by Grazvydas Ignotas to fix the console colors in OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJQRdW3AAoJECSVL5KnPj1PKpcQAJn9tS3BeTi9zcV5sk31U1Jy
kc72y318bg5jpJPDgWOfM+9CY3yhezVi2q9odiTUtuhx5WzWbOJh7/TuUGoWGKaY
dUvTqen83hFGKfTs+eujTbAgAH3+PGIGo5VmTyx1TVj5Vnb1m3wsU6jwDzalfox8
MChhoOyrCpn6wxiqSuF6eoqZ01jASsNDW1rQaxi6AdaKKxJXrG22phMpwmfZz9Mt
naIx1aI8aowkZ5gEBlOsnX6O0kjPVyQWlXqljGuZxRJZD+x9MKj/8nU1PITi0Pz2
DNAQz3ZU/apAooLCFsBF7oGtMUJ6e/v61LdIcMZZzw569tCtnmidwdU0ss2JJhAP
aDhdtWESbxFbpggOEWD36Wq6Z5ekCW5xfTR+ZASiknSMAT6rmqfX4NPJ3750jjVb
Aa9Ds37KQgfUrQIEhKCoZPyPTtCK98fQUHhxlf2I0TbuCGBvbZEAnRpuc1eelNo9
G9IJKG1vnea2x+DmsR1OEqFpHU3fn82T7RYm3SYc6ZDJwU58GxEvTzytGBs5YxLe
bTTM2mTT3m23l8BBp6UPZjESJoBv2bd+cY70MCxhVIKHXbQYdzet0DDEDA6t2UQK
isIOLXMGqxTXNZq7bM+q9UuYUuAkTUv1VmwGy5YJOD1JtOhFGQtxBe59OMmrC1H5
aU+GP6btV/biv8cTs/JG
=8eFG
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a fix by Paul Cercueil to prevent a possible buffer overflow
- a fix by Bruno Prémont to prevent a rare sleep in invalid context
- a fix by Julia Lawall for a double free in auo_k190x
- a fix by Dan Carpenter to prevent a division by zero in mb862xxfb
- a regression fix by Tomi Valkeinen for the SDI output in OMAP
- a fix by Grazvydas Ignotas to fix the console colors in OMAP
* tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6:
OMAPFB: fix framebuffer console colors
OMAPDSS: Fix SDI PLL locking
video: mb862xxfb: prevent divide by zero bug
drivers/video/auo_k190x.c: drop kfree of devm_kzalloc's data
fbcon: Fix bit_putcs() call to kmalloc(s, GFP_KERNEL)
fbcon: prevent possible buffer overflow.
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some cases.
Now we fix this by using 'kmem_cache_free()' instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Bin1
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi
Pull ubi fix from Artem Bityutskiy:
"A single small fix for memory deallocation: we allocated memory using
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some
cases. Now we fix this by using 'kmem_cache_free()' instead."
* tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi:
UBI: fix a horrible memory deallocation bug
Commit 644595f896 ("compat: Handle COMPAT_USE_64BIT_TIME in
net/socket.c") introduced a bug where the helper functions to take
either a 64-bit or compat time[spec|val] got the arguments in the wrong
order, passing the kernel stack pointer off as a user pointer (and vice
versa).
Because of the user address range check, that in turn then causes an
EFAULT due to the user pointer range checking failing for the kernel
address. Incorrectly resuling in a failed system call for 32-bit
processes with a 64-bit kernel.
On odder architectures like HP-PA (with separate user/kernel address
spaces), it can be used read kernel memory.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running 32-bit pvops-dom0 and a driver tries to allocate a coherent
DMA-memory the xen swiotlb-implementation returned memory beyond 4GB.
The underlaying reason is that if the supplied driver passes in a
DMA_BIT_MASK(64) ( hwdev->coherent_dma_mask is set to 0xffffffffffffffff)
our dma_mask will be u64 set to 0xffffffffffffffff even if we set it to
DMA_BIT_MASK(32) previously. Meaning we do not reset the upper bits.
By using the dma_alloc_coherent_mask function - it does the proper casting
and we get 0xfffffffff.
This caused not working sound on a system with 4 GB and a 64-bit
compatible sound-card with sets the DMA-mask to 64bit.
On bare-metal and the forward-ported xen-dom0 patches from OpenSuse a coherent
DMA-memory is always allocated inside the 32-bit address-range by calling
dma_alloc_coherent_mask.
This patch adds the same functionality to xen swiotlb and is a rebase of the
original patch from Ronny Hegewald which never got upstream b/c the
underlaying reason was not understood until now.
The original email with the original patch is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-02/msg00038.html
the original thread from where the discussion started is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-01/msg00928.html
Signed-off-by: Ronny Hegewald <ronny.hegewald@online.de>
Signed-off-by: Stefano Panella <stefano.panella@citrix.com>
Acked-By: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
While TLB_FLUSH_ALL gets passed as 'end' argument to
flush_tlb_others(), the Xen code was made to check its 'start'
parameter. That may give a incorrect op.cmd to MMUEXT_INVLPG_MULTI
instead of MMUEXT_TLB_FLUSH_MULTI. Then it causes some page can not
be flushed from TLB.
This patch fixed this issue.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Yongjie Ren <yongjie.ren@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit '4cb38750d49010ae72e718d46605ac9ba5a851b4': (6849 commits)
bcma: fix invalid PMU chip control masks
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895 bits
libata-acpi: add missing inlines in libata.h
i2c-omap: Add support for I2C_M_STOP message flag
i2c: Fall back to emulated SMBus if the operation isn't supported natively
i2c: Add SCCB support
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
...
We would traverse the full P2M top directory (from 0->MAX_DOMAIN_PAGES
inclusive) when trying to figure out whether we can re-use some of the
P2M middle leafs.
Which meant that if the kernel was compiled with MAX_DOMAIN_PAGES=512
we would try to use the 512th entry. Fortunately for us the p2m_top_index
has a check for this:
BUG_ON(pfn >= MAX_P2M_PFN);
which we hit and saw this:
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.1.2-OVM x86_64 debug=n Tainted: C ]----
(XEN) CPU: 0
(XEN) RIP: e033:[<ffffffff819cadeb>]
(XEN) RFLAGS: 0000000000000212 EM: 1 CONTEXT: pv guest
(XEN) rax: ffffffff81db5000 rbx: ffffffff81db4000 rcx: 0000000000000000
(XEN) rdx: 0000000000480211 rsi: 0000000000000000 rdi: ffffffff81db4000
(XEN) rbp: ffffffff81793db8 rsp: ffffffff81793d38 r8: 0000000008000000
(XEN) r9: 4000000000000000 r10: 0000000000000000 r11: ffffffff81db7000
(XEN) r12: 0000000000000ff8 r13: ffffffff81df1ff8 r14: ffffffff81db6000
(XEN) r15: 0000000000000ff8 cr0: 000000008005003b cr4: 00000000000026f0
(XEN) cr3: 0000000661795000 cr2: 0000000000000000
Fixes-Oracle-Bug: 14570662
CC: stable@vger.kernel.org # only for v3.5
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
patch_instruction() can be called very early on ppc32, when the kernel
isn't yet running at it's linked address. That can cause the !
is_kernel_addr() test in __put_user() to trip and call might_sleep()
which is very bad at that point during boot.
Use a lower level function instead for now, at least until we get to
rework ppc32 boot process to do the code patching later, like ppc64
does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state. This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux(). Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.
In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi(). In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.
This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store. This adds an explicit barrier in the two remaining cases.
These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.
The analysis of the reason why processes were not waking up properly
is due to Milton Miller.
Cc: stable@vger.kernel.org # v3.0+
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
With the four patches applied I can run a combination of all
test cases successfully at the same time:
http://ozlabs.org/~anton/junkcode/dscr_default_test.chttp://ozlabs.org/~anton/junkcode/dscr_explicit_test.chttp://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
This was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.
If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.
This issue was found with the following testcase:
http://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan