Extend the SPI device setup code to support this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Squashed nested structures.
Renamed remaining_len to out_len, ifc.len to in_len, header_length to
header_len.
Moved ipv4_id into the group of output variables where it belongs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.
Remove some redundant boolean temporaries.
Rename one field that looks like a flag but isn't.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unmap_addr since it can be calculated from dma_addr, len and
unmap_len. This saves 4-16 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add efx_poll_loopback() function to test for successful completion of test.
Change efx_test_loopback() to end the test after 1 ms if
efx_poll_loopback() indicates success, and otherwise to wait for 100 ms
as before.
While we're here, rename efx_{rx,tx}_loopback() to
efx_{begin,end}_loopback() which more accurately reflect their
purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removed log messages that are redundant with calling functions.
Fixed bitwise or-ing of return codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was making noise during 10Xpress self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These were clearly bogus.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Exclude assumed size of RX control frames from rx_bad_bytes.
Exclude assumed size of TX control frames from tx_good_bytes for
consistency with rx_good_bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We believed that some valid SNAP frames were being marked as invalid.
In fact this is not the case and no workaround is needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently the board initialisation includes 2 delays of 1 second each.
Usually it is unnecessary to wait that long, so check before doing so.
Correct some of the comments and log messages while we're here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
efx_test_loopback() used "|" to combine the results of the RX and TX
phases. If both phases fail with different error codes, this results
in a bogus error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Checksum generation is an attribute of our hardware TX queues, not TX
descriptors. We previously used a single queue and turned checksum
generation on or off as requested through ethtool. However, this can
result in regenerating checksums in raw packets that should not be
modified. We now create 2 hardware TX queues with checksum generation
on or off. They are presented to the net core as one queue since it
does not know how to select between them.
The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This means the compiler doesn't need to use real division instructions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use of the net_device::priv field is deprecated.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removes all _nested_compat() functions from the API. The prio qdisc
no longer requires them and netem has its own format anyway. Their
existance is only confusing.
Resend: Also remove the wrapper macro.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing in linux/pim.h should be exported to userspace.
This should fix the XORP build failure reported by
Jose Calhariz, the debain package maintainer.
Nothing originally in linux/mroute.h was exported to userspace
ever, but some of this stuff started to be when it was moved into
this new linux/pim.h, and that was wrong. If we didn't provide these
definitions for 10 years we can reasonably expect that applications
defined this stuff locally or used GLIBC headers providing the
protocol definitions. And as such the only result of this can
be conflict and userland build breakage.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.
This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill_mutex and rfkill->mutex are too easy to confuse with each other.
Rename rfkill_mutex to rfkill_global_mutex, so that they are easier to tell
apart with just one glance.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BUG_ON() and WARN() the heck out of buggy drivers calling into the rfkill
subsystem.
Also switch from WARN_ON(1) to the new descriptive WARN().
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial patch adding a missing line break on
rfkill_claim_show().
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.co>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switch sysfs parsing to something that actually works properly.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kernel doc syntax for comments and remove a few unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AR_DurUpdateEna is set, the frame's duration field
is updated by the MAC based on the current rate.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the all of p54pci's receiver code out of the
bloated interrupt handler routine and into a less critical tasklet.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware supports 8 different queues and not only 4.
So, let's make some room for further tasks (ap/adhoc support)
in this area.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings