Commit 9ee32fea5f unconditionally prevents the CPU from entering idle states
until intel_dp_aux_ch completes for the first time, which never happens on my
DisplayPort-less intel gfx, causing the CPU to get rather hot.
Signed-off-by: Tomas Janousek <tomi@nomi.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having 9500 lines repeated on dmesg does not help me at all.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on the platforms that have a dp aux irq and also have it
enabled - vlvhsw should have one, too. But I don't have a machine to
test this on. Judging from docs there's no dp aux interrupt for gm45.
Also, I only have an ivb cpu edp machine, so the dp aux A code for
snb/ilk is untested.
For dpcd probing when nothing is connected it slashes about 5ms of cpu
time (cpu time is now negligible), which agrees with 3 * 5 400 usec
timeouts.
A previous version of this patch increases the time required to go
through the dp_detect cycle (which includes reading the edid) from
around 33 ms to around 40 ms. Experiments indicated that this is
purely due to the irq latency - the hw doesn't allow us to queue up
dp aux transactions and hence irq latency directly affects throughput.
gmbus is much better, there we have a 8 byte buffer, and we get the
irq once another 4 bytes can be queued up.
But by using the pm_qos interface to request the lowest possible cpu
wake-up latency this slowdown completely disappeared.
Since all our output detection logic is single-threaded with the
mode_config mutex right now anyway, I've decide not ot play fancy and
to just reuse the gmbus wait queue. But this would definitely prep the
way to run dp detection on different ports in parallel
v2: Add a timeout for dp aux transfers when using interrupts - the hw
_does_ prevent this with the hw-based 400 usec timeout, but if the
irq somehow doesn't arrive we're screwed. Lesson learned while
developing this ;-)
v3: While at it also convert the busy-loop to wait_for_atomic, so that
we don't run the risk of an infinite loop any more.
v4: Ensure we have the smallest possible irq latency by using the
pm_qos interface.
v5: Add a comment to the code to explain why we frob pm_qos. Suggested
by Chris Wilson.
v6: Disable dp irq for vlv, that's easier than trying to get at docs
and hw.
v7: Squash in a fix for Haswell that Paulo Zanoni tracked down - the
dp aux registers aren't at a fixed offset any more, but can be on the
PCH while the DP port is on the cpu die.
Reviewed-by: Imre Deak <imre.deak@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Doesn't do anything yet than call dp_aux_irq_handler.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need two special things to properly wire this up:
- Add another argument to gmbus_wait_hw_status to pass in the
correct interrupt bit in gmbus4.
- Since we can only get an irq for one of the two events we want,
hand-roll the wait_event_timeout code so that we wake up every
jiffie and can check for NAKs. This way we also subsume gmbus
support for platforms without interrupts (or where those are not
yet enabled).
The important bit really is to only enable one gmbus interrupt source
at the same time - with that piece of lore figured out, this seems to
work flawlessly.
Ben Widawsky rightfully complained the lack of measurements for the
claimed benefits (especially since the first version was actually
broken and fell back to bit-banging). Previously reading the 256 byte
hdmi EDID takes about 72 ms here. With this patch it's down to 33 ms.
Given that transfering the 256 bytes over i2c at wire speed takes
20.5ms alone, the reduction in additional overhead is rather nice.
v2: Chris Wilson wondered whether GMBUS4 might contain some set bits
when booting up an hence result in some spurious interrupts. Since we
clear GMBUS4 after every wait and we do gmbus transfer really early in
the setup sequence to detect displays the window is small, but still
be paranoid and clear it properly.
v3: Clarify the comment that gmbus irq generation can only support one
kind of event, why it bothers us and how we work around that limit.
Cc: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only enables the interrupt and puts a irq handler into place, doesn't
do anything yet.
Unfortunately there's no gmbus interrupt support for gen2/3 (safe for
pnv, but there the irq is marked as "Test mode").
v2: Wire up the irq handler for vlv and gen4 properly.
v3: i915_enable_pipestat expects the mask bit, not the status bits ... and
for added hilarity those are rather inconsistently named.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise the new&shiny irq-driven gmbus and dp aux code won't work that
well. Noticed since the dp aux code doesn't have an automatic fallback
with a timeout (since the hw provides for that already).
v2: Simple move drm_irq_install before intel_modeset_gem_init, as
suggested by Ben Widawsky.
v3: Now that interrupts are enabled before all connectors are fully
set up, we might fall over serving a HPD interrupt while things are
still being set up. Instead of jumping through massive hoops and
complicating the code with a separate hpd irq enable step, simply
block out the hotplug work item from doing anything until things are
in place.
v4: Actually, we can enable hotplug processing only after the fbdev is
fully set up, since we call down into the fbdev from the hotplug work
functions. So stick the hpd enabling right next to the poll helper
initialization.
v5: We need to enable irqs before intel_modeset_init, since that
function sets up the outputs.
v6: Fixup cleanup sequence, too.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... together with all the other irq related resources in
intel_irq_init. I've managed to oops in the notify_ring function on my
ilk, presumably because of the powerctx setup call to i915_gpu_idle.
Note that this is only a problem with the reorder irq setup sequence
for irq-driver gmbus/dp aux.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is for legacy legacy stuff, and checking with the leftover
pipe from the previous loop is propably not what we want. Since
pipe == 2 after the loop ... Then we only assing a variable and do
nothing with it.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- __iomem where there is none (I love how we mix these things up).
- Use gfp_t instead of an other plain type.
- Unconfuse one place about enum pipe vs enum transcoder - for the pch
transcoder we actually use the pipe enum. Fixup the other cases
where we assign the pipe to the cpu transcoder with explicit casts.
- Declare the mch_lock properly in a header.
There is still a decent mess in intel_bios.c about __iomem, but heck,
this is x86 and we're allowed to do that.
Makes-sparse-happy: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use a space after the cast consistently and fix up the
newly-added cast in i915_irq.c to properly use __iomem.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to read/write the south interrupt register if the
corresponding bit is set in the north master interrupt register.
Noticed while reading our interrupt handling code.
Same optimization has already been applied on ivb in
commit 0e43406bcc
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed May 9 21:45:44 2012 +0100
drm/i915: Simplify interrupt processing for IvyBridge
We can take advantage that the PCH_IIR is a subordinate register to
reduce one of the required IIR reads, and that we only need to clear
interrupts handled to reduce the writes. And by simply tidying the code
we can reduce the line count and hopefully make it more readable.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should be useful to know what the driver thought the other ring's seqno
was when it last used a semaphore.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the power related code to run independently of the rest of
the pipeline, extending the resume and init time improvements into
userspace, which would otherwise have been blocked on the struct mutex
if we were doing PCU communication.
v2: Also convert the locking for the rps sysfs interface.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pretty astonishing how far apart these two members landed ... Especially since
I've already removed almost 200 lines in between.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the PIPECONF register is actually part of the CPU transcoder,
not the CPU pipe.
Ideally we would also rename PIPECONF to TRANSCONF to remind people
that they should use the transcoder instead of the pipe, but let's
keep it like this for now since most Gens still name it PIPECONF.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow this was left out in the refactoring that introduced the pch
handlers. Avoids a hotplug_mask special case in the ilk_irq_handler.
Noticed while hunting down the pch hotplug bits.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
round_jiffies() aligns the wakeup time to the nearest second in order to
batch wakeups and reduce system load, which is useful for unimportant
coarse timers like our hangcheck.
v2: round_jiffies_relative() returns the relative jiffie value, whereas
we need the absolute value for the timer.
Suggested-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Bigger -fixes pile, mostly because I've included Ajax' DP dongle stuff,
as discussed on irc. Otherwise just small things:
- regression fix to finally make 6bpc auto-dither on dp work (Jani)
- reinstate an snb ctx w/a that accidentally got lost in a rework (Chris)
- fixup the DP train sequence, logic-goof-up uncovered by Coverty (Chris)
- fix set_caching locking (Ben)
- fix spurious segfault on con-current gtt mmap faulting (Dimitry and Mika)
- some pageflip correctness fixes (still hunting down some issues, but
these are the worst offenders of confused code that we've tracked down
thus far) from Chris and me
- fixup swizzling settings on vlv (Jesse)
- gt_mode w/a from Ben added, fixes snb gt1 rc6+hw ctx hangs.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix GT_MODE default value
drm/i915: don't frob the vblank ts in finish_page_flip
drm/i915: call drm_handle_vblank before finish_page_flip
drm/i915: print warning if vmi915_gem_fault error is not handled
drm/i915: EBUSY status handling added to i915_gem_fault().
drm/i915: Try harder to complete DP training pattern 1
drm/i915: set swizzling to none on VLV
drm/dp: Make sink count DP 1.2 aware
drm/dp: Document DP spec versions for various DPCD registers
drm/i915/dp: Be smarter about connection sense for branch devices
drm/i915/dp: Fetch downstream port info if needed during DPCD fetch
drm/dp: Update DPCD defines
drm: Export drm_probe_ddc()
drm/i915: Flush the pending flips on the CRTC before modification
drm/i915: Actually invalidate the TLB for the SandyBridge HW contexts w/a
drm/i915: Fix set_caching locking
drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag
... since finish_page_flip needs the vblank timestamp generated
in drm_handle_vblank. Somehow all the gmch platforms get it right,
but all the pch platform irq handlers get is wrong. Hooray for copy&
pasting!
Currently this gets papered over by a gross hack in finish_page_flip.
A second patch will remove that.
Note that without this, the new timestamp sanity checks in flip_test
occasionally get tripped up, hence the cc: stable tag.
Cc: stable@vger.kernel.org
Reviewed-by: mario.kleiner@tuebingen.mpg.de
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
I'm official fed up with the yelling and useless indirection.
Let it burn!
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixed SDVOB and SDVOC bit definitions for Valleyview.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new "standardized" sysfs interfaces we need to be a bit more
careful about setting the RPS values.
Because the sysfs code and the rps workqueue can run at the same time,
if the sysfs setter wins the race to the mutex, the workqueue can come
in and set a value which is out of range (ie. we're no longer protecting
by RPINTLIM).
I was not able to actually make this error occur in testing.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than have multiple data structures for describing our page layout
in conjunction with the array of pages, we can migrate all users over to
a scatterlist.
One major advantage, other than unifying the page tracking structures,
this offers is that we replace the vmalloc'ed array (which can be up to
a megabyte in size) with a chain of individual pages which helps reduce
memory pressure.
The disadvantage is that we then do not have a simple array to iterate,
or to access randomly. The common case for this is in the relocation
processing, which will typically fit within a single scatterlist page
and so be almost the same cost as the simple array. For iterating over
the array, the extra function call could be optimised away, but in
reality is an insignificant cost of either binding the pages, or
performing the pwrite/pread.
v2: Fix drm_clflush_sg() to not invoke wbinvd as well! And fix the
trivial compile error from rebasing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we've only frobbed this bit at irq_init time, but did
not restore it at resume time. Move it to the gen3 clock gating
function to fix this.
Notice while reading through code.
Cc: stable@vger.kernel.org (for 3.5 only)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like with the equivalent change for gen6+ rps state, this helps in
clarifying the code (and in fixing a few places that have fallen through
the cracks in the locking review).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise it just won't compile ...
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Using the extracted INSTDONE reading, and our new register definitions,
update our hangcheck detection and error collection to use it. This
primarily means changing == to memcmp, and changing = to memcpy.
Hopefully this will give more info on error dump, and provide more
accurate hangcheck detection (both are actually TBD).
Also, remove the reading of instdone1 from the ring error collection
function, and just crap everything in capture_error_state (that could be
split into a separate patch if it wasn't so trivial).
v2: Now assuming i915_get_extra_instdone does the memset we can clean up the
code a bit (Jani)
v3: use ARRAY_SIZE as requested earlier by Jani (didn't change sizeof)
Updated commit msg
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
INSTDONE is used in many places, and it varies from generation to
generation. This provides a good reason for us to extract the logic to
read the relevant information.
The patch has no functional change. It's prep for some new stuff.
v2: move the memset inside of i915_get_extra_instdone (Jani)
v3,4: bugs caught by (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ERR_INT can generate interrupts. However since most of the conditions seem
quite fatal the patch opts to simply report it in error state instead of
adding more complexity to the interrupt handler for little gain (the
bits are sticky anyway).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When dealing with a working set larger than the GATT, or even the
mappable aperture when touching through the GTT, we end up with evicting
objects only to rebind them at a new offset again later. Moving an
object into and out of the GTT requires clflushing the pages, thus
causing a double-clflush penalty for rebinding.
To avoid having to clflush on rebinding, we can track the pages as they
are evicted from the GTT and only relinquish those pages on memory
pressure.
As usual, if it were not for the handling of out-of-memory condition and
having to manually shrink our own bo caches, it would be a net reduction
of code. Alas.
Note: The patch also contains a few changes to the last-hope
evict_everything logic in i916_gem_execbuffer.c - we no longer try to
only evict the purgeable stuff in a first try (since that's superflous
and only helps in OOM corner-cases, not fragmented-gtt trashing
situations).
Also, the extraction of the get_pages retry loop from bind_to_gtt (and
other callsites) to get_pages should imo have been a separate patch.
v2: Ditch the newly added put_pages (for unbound objects only) in
i915_gem_reset. A quick irc discussion hasn't revealed any important
reason for this, so if we need this, I'd like to have a git blame'able
explanation for it.
v3: Undo the s/drm_malloc_ab/kmalloc/ in get_pages that Chris noticed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Split out code movements and rant a bit in the commit message
with a few Notes. Done v2]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQLWtvAAoJEHm+PkMAQRiG/DYH+wd0FqfEuYkYk4KPyAPuhKpX
zX7HYfLvyJE/ZYIdrhjq1E6Xm2KNr7gtX7/Rdzi2W38M9sjbYzwG1UGIw51qnxWy
yZJH9BGkfyQgQPeuDGohfB6DkDy2JWr2eqMDvakjOwgBsIzji0PQD/f3UvndhtUa
c+tTj/kjavHE1Yr2Wy6OnRZz3Uc0hIMn/Q0JqtbCs3LUgEV1KA4OEAe56XNz4Ku4
WE+FFaGFPvtriQsQON+ohPS5IC8jzQGK/0vbrJ4lWjFnZy4gvZXnborTOwD0WSQG
fbsNuxp1AaM2/pqfMwXm1w0ADvwOITHNiwwXf9id6DoK81QwTFpUdvKpn6yB6gQ=
=rurr
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc2' into drm-intel-next
Backmerge Linux 3.6-rc2 to resolve a few funny conflicts before we put
even more madness on top:
- drivers/gpu/drm/i915/i915_irq.c: Just a spurious WARN removed in
-fixes, that has been changed in a variable-rename in -next, too.
- drivers/gpu/drm/i915/intel_ringbuffer.c: -next remove scratch_addr
(since all their users have been extracted in another fucntion),
-fixes added another user for a hw workaroudn.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid the forcewake overhead when simply retiring requests, as often the
last seen seqno is good enough to satisfy the retirment process and will
be promptly re-run in any case. Only ensure that we force the coherent
seqno read when we are explicitly waiting upon a completion event to be
sure that none go missing, and also for when we are reporting seqno
values in case of error or debugging.
This greatly reduces the load for userspace using the busy-ioctl to
track active buffers, for instance halving the CPU used by X in pushing
the pixels from a software render (flash). The effect will be even more
magnified with userptr and so providing a zero-copy upload path in that
instance, or in similar instances where X is simply compositing DRI
buffers.
v2: Reverse the polarity of the tachyon stream. Daniel suggested that
'force' was too generic for the parameter name and that 'lazy_coherency'
better encapsulated the semantics of it being an optimization and its
purpose. Also notice that gen6_get_seqno() is only used by gen6/7
chipsets and so the test for IS_GEN6 || IS_GEN7 is redundant in that
function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We change the drps/ips sw/hw state from different callers: Our own irq
handler, the external intel-ips module and from process context. Most
of these callers don't take any lock at all.
Protect everything by making the mchdev_lock irqsave and grabbing it in
all relevant callsites. Note that we have to convert a few sleeps in the
drps enable/disable code to delays, but alas, I'm not volunteering to
restructure the code around a few work items.
For paranoia add a spin_locked assert to ironlake_set_drps, too.
v2: Move one access inside the lock protection. Caught by the
dev_priv->ips mass-rename ...
v3: Resolve rebase conflict.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like all the other drps/ips stuff. Hence add the corresponding check,
give the function a preciser prefix and move the single reg clearing into
the rps handling function, too.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way it's easier so see what belongs together, and what is used
by the ilk ips code. Also add some comments that explain the locking.
Note that (cur|min|max)_delay need to be duplicated, because
they're also used by the ips code.
v2: Missed one place that the dev_priv->ips change caught ...
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes: (this pull is the one with the bad patch dropped)
First pile of fixes for 3.6 already, and I'm afraid it's a bit larger than
what I'd wish for. But I've moved all the feature-y stuff to -next, so
this really is all -fixes. Most of it is handling fallout from the hw
context stuff, discovered now that mesa git has started using them for
real. Otherwise all just small fixes:
- unbreak modeset=0 on gen6+ (regressed in next)
- const mismatch fix for ->mode_fixup
- simplify overly clever lvds modeset code (current code can totally
confuse backlights, resulting in broken panels until a full power draw
restores them).
- fix some fallout from the flushing_list disabling (regression only
introduced in -next)
- DP link train improvements (this also kills the last 3.2 dp regression
afaik)
- bugfix for the new ddc VGA detection on newer platforms
- minor backlight fixes (one of them a -next regression)
- only enable the required PM interrupts (to avoid waking up the cpu
unnecessarily)
- some really minor bits (workaround clarification, make coverty happy,
hsw init fix)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (23 commits)
drm/i915: unbreak lastclose for failed driver init
drm/i915: Set the context before setting up regs for the context.
drm/i915: constify mode in crtc_mode_fixup
drm/i915/lvds: ditch ->prepare special case
drm/i915: dereferencing an error pointer
drm/i915: fix invalid reference handling of the default ctx obj
drm/i915: Add -EIO to the list of known errors for __wait_seqno
drm/i915: Flush the context object from the CPU caches upon switching
drm/i915: Make the lock for pageflips interruptible
drm/i915: don't forget the PCH backlight registers
drm/i915: Insert a flush between batches if the breadcrumb was dropped
drm/i915: missing error case in init status page
drm/i915: mask tiled bit when updating ILK sprites
drm/i915: try to train DP even harder
drm/i915: kill intel_ddc_probe
drm/i915: check whether we actually received an edid in detect_ddc
drm/i915: fix up PCH backlight #define mixup
drm/i915: Add comments to explain the BSD tail write workaround
drm/i915: Disable the BLT on pre-production SNB hardware
drm/i915: initialize power wells in modeset_init_hw
...
Originally I had a macro specifically for DPF support, and Daniel, with
good reason asked me to change it to this. It's not the way I would have
gone (and indeed I didn't), but for now there is no distinction as all
platforms with L3 also have DPF.
Note: The good reasons are that dpf is a l3$ feature (at least on
currrent hw), hence I don't expect one to go without the other.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: added note]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we always flush the GPU cache prior to emitting the breadcrumb, we no
longer have to worry about the deferred flush causing the
pending_gpu_write to be delayed. So we can instead utilize the known
last_write_seqno to hopefully minimise the wait times.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having had to dive into the bspec to understand what each stage of the
workaround meant, and how that the ring broadcasting IDLE corresponded
with the GT powering down the ring (i.e. rc6) add comments to aide
the next reader.
And since the register "is used to control all aspects of PSMI and power
saving functions" that makes it quite interesting to inspect with
regards to RC6 hangs, so add it to the error-state.
v2: Rediscover the piece of magic, set the RNCID to 0 before waiting for
the ring to wake up.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQAfWKAAoJEHm+PkMAQRiG/DwIAIullMhkDhD/GJcn24ZbUJoa
v6zRPK2hIavuKH/6bUoUiXT346PUYgVnRMhetuYKJFURz6KX/nmlxve/iXNn/WP1
9hnxhE+zcnp2qKI83c3Yok09eed1KnGY5hWQkqXM2gzji/OU0pCKchOcL01l//uz
iiWpNAXEVUnT92CafnHlZ55f/MWVqRFmDKi3Ty1YKSskhojQ6NOPsWCxrTxKVbim
2YPXc3D+xLHzF12ufVgla20AF4KnK8m+tFugniRAqArIagpzBUP1x1wk0RN5PyBD
FTP8lv7bSfBusp41/mPDB66WAe9EfQBoWQY6jloJjp0i8xnMyH5V05pImBV5NwU=
=O+gl
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc7' into drm-next
Merge Linus tree into drm to fixup conflicts in radeon code for further
testing before upstream merge.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/radeon/radeon_gart.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into drm-intel-next-queued
I want to merge the "no more fake agp on gen6+" patches into
drm-intel-next (well, the last pieces). But a patch in 3.5-rc4 also
adds a new use of dev->agp. Hence the backmarge to sort this out, for
otherwise drm-intel-next merged into Linus' tree would conflict in the
relevant code, things would compile but nicely OOPS at driver load :(
Conflicts in this merge are just simple cases of "both branches
changed/added lines at the same place". The only tricky part is to
keep the order correct wrt the unwind code in case of errors in
intel_ringbuffer.c (and the MI_DISPLAY_FLIP #defines in i915_reg.h
together, obviously).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ringbuffer.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After banging my head against this for the past few months, I still
don't see how this could possible race under the premise that once an
irq bit is masked in PM_IMR and reset in PM_IIR it won't show up again
until we unmask it in PM_IMR.
Still, we have reports of this being seen in the wild. Now Bspec has
this little bit of lovely language in the PMIIR register:
Public SNB Docs, Vol3Part2, 2.5.14 "PMIIR":
"For each bit, the IIR can store a second pending interrupt if two or
more of the same interrupt conditions occur before the first condition
is cleared. Upon clearing the interrupt, the IIR bit will momentarily
go low, then return high to indicate there is another interrupt
pending."
Now if we presume that PMIMR only prevent new interrupts from being
queued, we could easily end up masking an interrupt and clearing it,
but the 2nd pending interrupt setting the bit in PMIIR right away
again. Which leads, the next time the irq handler runs, to hitting the
WARN.
Also, no bad side effects of this have ever been reported. And we've
tracked down our issues with the gpu turbo getting stuck to bogus
interrupt generation limits in th RPLIMIT register.
So let's just rip out this WARN as bogus and call it a day. The only
shallow thing here is that this 2-deep irq queue in the hw makes you
wonder how racy the windows irq handler is ...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42907
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And restructure the IRQ handling a little. We can use pipestat for most
things, and make sure we don't affect pipe events when enabling and
disabling vblank interupts.
We can leave vblank interrupts masked but enabled so we're not dependent
on the first client to toggle the disable timer. We can also mask all
render based interrupts, since the ring code will handle unmasking them
for us.
v2: roll in vblank masking, remove unneeded variable (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cougar/Panther Point redefine the bits in SDEIIR pretty completely.
This function is just debugging, but if we're debugging we probably want
to be told accurate things instead of lies.
I'm told Lynx Point changes this yet more, but I have no idea how...
Note from Eugeni's review:
"For the record and for future enabling efforts, for LPT, bits 28-31
and 1-14 are gone since CPT/PPT (e.g., those must be zero). And there
is the bit 15 as a new addition, but we are not using it yet and
probably won't be using in foreseeable future."
Signed-off-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35103
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes an (albeit really hard to hit) race resulting in an oops:
- The parity work get scheduled.
- We re-init the irq state and call INIT_WORK again.
- The workqueue code tries to run the work item and stumbles over a
work item that should be on it's runlist.
Also initiliaze the work item unconditionally like all the others,
it's simpler.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous patch put all the code, and handlers in place. It should
now be safe to enable the parity error interrupt. The parity error must
be unmasked in both the GTIMR, and the CS IMR. Unfortunately, the docs
aren't clear about this; nevertheless it's the truth.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only. This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).
When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.
Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.
V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to avoid missed down-interrupts when coming out of RC6, it is
advised that we always reset the down-threshold upon a PM event. This is
due to that the PM unit goes through a little dance when coming out of
RC6, it first brings the GPU up at the lowest frequency then a short
time later it restores the thresholds. During that interval, the
down-interval may expire and the interrupt be suppressed.
Now aware of the dance taking place within the GPU when coming out of
RC6, one wonders what other writes need to be queued in the fifo buffer
in order to be properly sequenced; setting the RP state appears to be
one.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44006
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that gen3 is the only platform where we've got the bit
definitions right, hence the workaround of disabling sdvo hotplug
support on i945g/gm is not due to misdiagnosis of broken hotplug irq
handling ...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: add some blurb about sdvo hotplug fail on i945g/gm I've
wondered about while reviewing.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also as we set the HOTPLUG_EN to 0 during pre-install, we can simply set
it during post-install, and nor do we wish to enable unwanted hotplug
events.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.
Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.
Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.
v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell interrupts are mostly similar with Ivy Bridge, so we share same
routines with it.
This patch also simplifies the vblank counter handling for all the Gen5+
architectures.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can take advantage that the PCH_IIR is a subordinate register to
reduce one of the required IIR reads, and that we only need to clear
interrupts handled to reduce the writes. And by simply tidying the code
we can reduce the line count and hopefully make it more readable.
v2: Split out the bugfix from the refactoring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only half of them even cared, and it's always the same one.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- reduce the irq disabled section, even for a debugfs file this was
way too long.
- always disable irqs when taking the lock.
v2: Thou shalt not mistake locking for reference counting, so:
- reference count the error_state to protect from concurent freeeing.
This will be only really used in the next patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and hide it in i915_dma.c.
This way all the legacy stuff dealing with READ_BREADCRUMB and
LP_RING and friends is in i915_dma.c.
v2: Rebase on top of Chris Wilson's rework irq handling code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just get this out of the way.
v2: Rebase against ENODEV changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never supported dri1 on gen5+.
VLV never had that code, so no need to remove it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_dma.c contains most of the old dri1 horror-show, so move
the remaining bits there, too. The code has been removed and
the only thing left are some stubs to ensure that userspace
doesn't try to use this stuff. vblank_pipe_set only returns 0
without any side-effects, so we can even stub it out with
the canonical drm_noop.
v2: Rebase against ENODEV changes.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vblank_pipe was intended to be used for tracking DRI1 state. However,
the vblank_pipe reported to DRI1 is fixed to umask both pipes, and the
dev_priv->vblank_pipe unused and superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The waiting_seqno is not terribly useful, and as such we can remove it
so that we'll be able to extract lockless code.
v2: Keep the information for error_state (Chris)
Check if ring is initialized in hangcheck (Chris)
Capture the waiting ring (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: add some bikeshed to clarify a comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extra bit of interrupt enabling code doesn't belong in the wait
seqno function. If anything we should pull it out to a helper so the
throttle code can also use it. The history is a bit vague, but I am
going to attempt to just dump it, unless someone can argue otherwise.
Removing this allows for a shared lock free wait seqno function. To keep
tabs on this issue though, the IER value is stored on error capture
(recommended by Chris Wilson)
v2: fixed typo EIR->IER (Ben)
Fix some white space (Ben)
Move IER capture to globally instead of per ring (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: ier is a 16 bit reg on gen2!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since there is only one remaining user of I915_INTERRUPT_ENABLE_FIX,
expand it at the callsite. Quoting Jesse Barnes:
"I'd really like to get rid of these defines at the top of i915_irq.c.
Some are unused and the others just make you check for the right bits
everytime your read the code."
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add bikeshed suggested by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We appear to allow too many pending pageflips as evidenced by an
apparent pin-leak. So borrow the pageflip completion logic from i8xx for
handling PendingFlip in a robust manner.
v2: Address Jesse's reminders about the nuances of gen3 IRQ handling.
References: https://bugzilla.kernel.org/show_bug.cgi?id=41882
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bring the for-each-pipe loops together so that the code is easier on the
eyes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple of miscellaneous cleanups as well to move per-loop condition
variables within the scope of the loop and the update of the DRI1
breadcrumb to the tail of the function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And a couple of miscellaneous cleanups to the main body of the IRQ loop;
move per-loop condition variables within the scope of the loop and move
the old DRI1 breadcrumb to the tail of the function and so only execute
it once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On later gen3, you are able to select the meaning of the FlipPending
status bit in IIR and change it to FlipDone. This was sometimes done by
the BIOS leading to confusion on just how pageflipping worked on gen3.
Simplify the implementation by using the legacy meaning for all gen3
machines.
Note: this makes all gen3 machines equally broken...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for rewriting the gen3 irq handler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And remove the cargo-culted copy from the valleyview irq handler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The waitqueues are already initialised during ring initialisation so
kill the redundant and duplicated code to do so in each generations IRQ
installer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than duplicate similar code across the IRQ installers, perform
the initialisation of the workers upfront. This will lead to simpler
teardown and quiescent code as we can assume that the workers have
been initialised.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling these when gem assumes full control of the hw won't end
in anything else than tears. So be a bit more paranoid here.
Just serves as documentation.
v2: Bail out with ENODEV as suggested by Chris Wilson.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplify object tracking by removing the inactive but pinned list. The
only place where this was used is for counting the available memory,
which is just as easy performed by checking all objects on the rare
occasions it is required (application startup). For ease of debugging,
we keep the reporting of pinned objects through the error-state and
debugfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and put them to so good use.
Note that there's functional change in vlv clock gating code, we now
no longer spuriously read back the current value of the bit. According
to Bspec the high bits should always read zero, so ORing this in
should have no effect.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gen2 hardware has some significant differences from the other interrupt
routines that were glossed over and then forgotten about in the
transition to KMS. Such as
- 16bit IIR
- PendingFlip status bit
This patch reintroduces a handler specifically for gen2 for the purpose
of handling pageflips correctly, simplifying code in the process.
v2: Also fixup ring get/put irq to only access 16bit registers (Daniel)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24202
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41793
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: use posting_read16 in intel_ringbuffer.c and kill _driver
from the function names.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The purpose of this patch is to avoid zeroing the lower 12 reserved bits
of surface base address registers (framebuffer & sprite). There are bits
in that range that may occasionally be set by BIOS or by other components.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function, along with the registers and deferred work hander, are
all shared with SandyBridge, IvyBridge and their variants. So remove the
duplicate code into a single function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the first instance we just wish to kick the waiters and see if that
terminates the wait conditions. If it does not, then we do not want to
keep retrying without ever making any forward progress and becoming
stuck in a hangcheck loop.
Reported-and-tested-by: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48209
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv, ivb and snb all share the gen6+ gt irq handling. 3 copies of the
same stuff is a bit much, so extract it into a little helper.
Now ilk has a different gt irq handling than snb, but shares the same
irq handler (due to the similar display block). So also extract the
ilk gt irq handling to clearly separate these two things.
Nice side effect of this is that we can complete Ben Widawsky's gen6+
irq bit #define cleanup and call the render irq also with the GEN6
alias. Beforehand that code was shared with ilk, and neither option
really made much sense.
As a bonus this enables the error interrupt handling lifted from the
vlv code on snb and ivb, too.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Antagonized-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got copy-pasted from an older version. The newer kinds of
workarounds don't need this anymore.
Shame on me for not noticing when picking up the vlv irq patch.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tomas Janousek