ioctl debugging can now be done through the debug parameter in sysfs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a poor administration of the driver state it wasn't possible to open
a video or vbi device multiple times.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usual set of problems: the frequency isn't clamped to the frequency range,
no tuner index check and the frequency isn't initialized properly on module
load.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This switch to v4l2_fh resolves the last v4l2_compliance issues with respect
to control events and priority handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The input and audio ioctls are only valid for video/vbi nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver already does locking, so it is safe to switch to unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver now passes the tuner and frequency tests of v4l2-compliance.
It's the usual bugs: frequency wasn't clamped to the valid frequency range,
incorrect tuner capabilities and tuner fields not filled in, missing test
for invalid tuner index, no initial frequency and incorrect error handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the correct parent for v4l2_device_register and don't set the name
anymore (that's now deduced from the parent). Also remove an unnecessary
forward reference and fix two weird looking log messages.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using 3.3 MHz IF, use 4MHz. That's the standard
value for the demod, and, while it can be adjusted, 3.3 MHz
is out of the recommended range. So, let's stick with the
default.
With regards to the IF voltage level, instead of using
0.5 V(p-p) for IF, use 2V, giving a 12dB gain.
The rationale is that, on PixelView SBTVD Hybrid,
even 2V(p-p) would be in the nominal range for IF,
as the maximum range on this particular device is 3V.
A higher gain here should help to improve reception under
weak signals.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new eeproms with 16 address width still have the the device config dataset
(the content of the old 8 bit eeproms) embedded.
Hauppauge also continues to include the tveeprom data structure inside this
dataset in their devices.
The start address of the dataset depends on the start address of the microcode
and a variable additional offset.
It should be mentioned that Camera devices seem to use a different dataset type,
which is not yet supported.
Tested with devices "Hauppauge HVR-930C". I've also checked the USB-log from the
"MSI Digivox ATSC" and it works the same way.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We currently reserve an array of 256 bytes for the eeprom content in the device
struct. For eeproms with 16 bit address width it might even be necessary to
increase the buffer size further.
Having such a big chunk of memory reserved even if the device has no eeprom and
keeping it after it has already been processed seems to be a waste of memory.
Change the code to allocate + free the eeprom memory dynamically.
This also makes it possible to handle different dataset sizes depending on what
is stored/found in the eeprom.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a helper function for reading data blocks from i2c devices with 8 or 16 bit
address width and 8 bit register width.
This allows us to reduce the size of new code added by the following patches.
Works only for devices with activated register auto incrementation.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer devices (em2874, em2884, em28174, em25xx, em27[6,7,8]x) use eeproms with
16 bit instead of 8 bit address width.
The used eeprom type depends on the chip type, which makes sure eeproms can't
be damaged.
This patch adds basic support for 16 bit eeproms only, which includes
- reading the content
- calculating the eeprom hash
- displaying the content
The eeprom content uses a different format, for which support will be added with
subsequent patches.
Tested with the "Hauppauge HVR-930C" and the "Speedlink VAD Laplace webcam"
(with additional experimental patches).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The data is stored as little endian in the eeprom.
Hence the correct data types should be used and the data should be converted
to the machine endianess before using it.
The eeprom id (key) also isn't a 32 bit value but 4 separate bytes instead.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduces the number of characters/lines, unifies the code and improves readability.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only a single place where the dprintk2 macro is used, so get rid of it.
[mchehab@redhat.com: fix checkpathc.pl complain:
ERROR: space prohibited before that close parenthesis ')']
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output resolutions <=20% of the input resolution exceed the capabilities of the
scaler.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoids registering a VBI device and streaming in VBI-mode if the device is a
camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a "normal" and not an "advanced" debug functionality.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_disconnect() is called when the device is disconnected, so that the
v4l2-core rejects all ioctl calls.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner type is set by the v4l2-core based on the device type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_s_fmt_vbi_cap() is a 100% duplicate of vidioc_g_fmt_vbi_cap() and
therefore can be removed.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver doesn't support the VIDIOC_G_CROP and VIDIOC_S_CROP ioctls,
so VIDIOC_CROPCAP is useless and has the potential to confuse applications,
because it can be interpreted as indicator for cropping support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current code V4L2_BUF_TYPE_VIDEO_CAPTURE is accepted only, but for VBI
devices only buffer type V4L2_BUF_TYPE_VBI_CAPTURE is used/valid.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PARM doesn't make sense for VBI device nodes, because we don't support
selecting the number of read buffers to use.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
function, use v4l2_disable_ioctl() to disable the ioctl VIDIOC_S_PARM if the
device is not a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil