The bit is supposed to be '1' when SMT is not supported or forcefully
disabled and '0' otherwise.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V 2019 doesn't expose MD_CLEAR CPUID bit to guests when it cannot
guarantee that two virtual processors won't end up running on sibling SMT
threads without knowing about it. This is done as an optimization as in
this case there is nothing the guest can do to protect itself against MDS
and issuing additional flush requests is just pointless. On bare metal the
topology is known, however, when Hyper-V is running nested (e.g. on top of
KVM) it needs an additional piece of information: a confirmation that the
exposed topology (wrt vCPU placement on different SMT threads) is
trustworthy.
NoNonArchitecturalCoreSharing (CPUID 0x40000004 EAX bit 18) is described in
TLFS as follows: "Indicates that a virtual processor will never share a
physical core with another virtual processor, except for virtual processors
that are reported as sibling SMT threads." From KVM we can give such
guarantee in two cases:
- SMT is unsupported or forcefully disabled (just 'disabled' doesn't work
as it can become re-enabled during the lifetime of the guest).
- vCPUs are properly pinned so the scheduler won't put them on sibling
SMT threads (when they're not reported as such).
This patch reports NoNonArchitecturalCoreSharing bit in to userspace in the
first case. The second case is outside of KVM's domain of responsibility
(as vCPU pinning is actually done by someone who manages KVM's userspace -
e.g. libvirt pinning QEMU threads).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM needs to know if SMT is theoretically possible, this means it is
supported and not forcefully disabled ('nosmt=force'). Create and
export cpu_smt_possible() answering this question.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:__apic_accept_irq+0x46/0x740 arch/x86/kvm/lapic.c:1029
Call Trace:
kvm_apic_set_irq+0xb4/0x140 arch/x86/kvm/lapic.c:558
stimer_notify_direct arch/x86/kvm/hyperv.c:648 [inline]
stimer_expiration arch/x86/kvm/hyperv.c:659 [inline]
kvm_hv_process_stimers+0x594/0x1650 arch/x86/kvm/hyperv.c:686
vcpu_enter_guest+0x2b2a/0x54b0 arch/x86/kvm/x86.c:7896
vcpu_run+0x393/0xd40 arch/x86/kvm/x86.c:8152
kvm_arch_vcpu_ioctl_run+0x636/0x900 arch/x86/kvm/x86.c:8360
kvm_vcpu_ioctl+0x6cf/0xaf0 arch/x86/kvm/../../../virt/kvm/kvm_main.c:2765
The testcase programs HV_X64_MSR_STIMERn_CONFIG/HV_X64_MSR_STIMERn_COUNT,
in addition, there is no lapic in the kernel, the counters value are small
enough in order that kvm_hv_process_stimers() inject this already-expired
timer interrupt into the guest through lapic in the kernel which triggers
the NULL deferencing. This patch fixes it by don't advertise direct mode
synthetic timers and discarding the inject when lapic is not in kernel.
syzkaller source: https://syzkaller.appspot.com/x/repro.c?x=1752fe0a600000
Reported-by: syzbot+dff25ee91f0c7d5c1695@syzkaller.appspotmail.com
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Zapping collapsible sptes, a.k.a. 4k sptes that can be promoted into a
large page, is only necessary when changing only the dirty logging flag
of a memory region. If the memslot is also being moved, then all sptes
for the memslot are zapped when it is invalidated. When a memslot is
being created, it is impossible for there to be existing dirty mappings,
e.g. KVM can have MMIO sptes, but not present, and thus dirty, sptes.
Note, the comment and logic are shamelessly borrowed from MIPS's version
of kvm_arch_commit_memory_region().
Fixes: 3ea3b7fa9a ("kvm: mmu: lazy collapse small sptes into large sptes")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the duplication code in run_test() of dirty_log_test because
after some reordering of functions now we can directly use the outcome
of vm_create().
Meanwhile, with the new VM_MODE_PXXV48_4K, we can safely revert
b442324b58 too where we stick the x86_64 PA width to 39 bits for
dirty_log_test.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The naming VM_MODE_P52V48_4K is explicit but unclear when used on
x86_64 machines, because x86_64 machines are having various physical
address width rather than some static values. Here's some examples:
- Intel Xeon E3-1220: 36 bits
- Intel Core i7-8650: 39 bits
- AMD EPYC 7251: 48 bits
All of them are using 48 bits linear address width but with totally
different physical address width (and most of the old machines should
be less than 52 bits).
Let's create a new guest mode called VM_MODE_PXXV48_4K for current
x86_64 tests and make it as the default to replace the old naming of
VM_MODE_P52V48_4K because it shows more clearly that the PA width is
not really a constant. Meanwhile we also stop assuming all the x86
machines are having 52 bits PA width but instead we fetch the real
vm->pa_bits from CPUID 0x80000008 during runtime.
We currently make this exclusively used by x86_64 but no other arch.
As a slight touch up, moving DEBUG macro from dirty_log_test.c to
kvm_util.h so lib can use it too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since we've just removed the dependency of vm type in previous patch,
now we can create the vm much earlier. Note that to move it earlier
we used an approximation of number of extra pages but it should be
fine.
This prepares for the follow up patches to finally remove the
duplication of guest mode parsings.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than passing the vm type from the top level to the end of vm
creation, let's simply keep that as an internal of kvm_vm struct and
decide the type in _vm_create(). Several reasons for doing this:
- The vm type is only decided by physical address width and currently
only used in aarch64, so we've got enough information as long as
we're passing vm_guest_mode into _vm_create(),
- This removes a loop dependency between the vm->type and creation of
vms. That's why now we need to parse vm_guest_mode twice sometimes,
once in run_test() and then again in _vm_create(). The follow up
patches will move on to clean up that as well so we can have a
single place to decide guest machine types and so.
Note that this patch will slightly change the behavior of aarch64
tests in that previously most vm_create() callers will directly pass
in type==0 into _vm_create() but now the type will depend on
vm_guest_mode, however it shouldn't affect any user because all
vm_create() users of aarch64 will be using VM_MODE_DEFAULT guest
mode (which is VM_MODE_P40V48_4K) so at last type will still be zero.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was discovered that after commit 65efa61dc0 ("selftests: kvm: provide
common function to enable eVMCS") hyperv_cpuid selftest is failing on AMD.
The reason is that the commit changed _vcpu_ioctl() to vcpu_ioctl() in the
test and this one can't fail.
Instead of fixing the test is seems to make more sense to not announce
KVM_CAP_HYPERV_ENLIGHTENED_VMCS support if it is definitely missing
(on svm and in case kvm_intel.nested=0).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 5158917c7b ("KVM: x86: nVMX: Allow nested_enable_evmcs to
be NULL") the code in x86.c is prepared to see nested_enable_evmcs being
NULL and in VMX case it actually is when nesting is disabled. Remove the
unneeded stub from SVM code.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V provides direct tlb flush function which helps
L1 Hypervisor to handle Hyper-V tlb flush request from
L2 guest. Add the function support for VMX.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V direct tlb flush function should be enabled for
guest that only uses Hyper-V hypercall. User space
hypervisor(e.g, Qemu) can disable KVM identification in
CPUID and just exposes Hyper-V identification to make
sure the precondition. Add new KVM capability KVM_CAP_
HYPERV_DIRECT_TLBFLUSH for user space to enable Hyper-V
direct tlb function and this function is default to be
disabled in KVM.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The struct hv_vp_assist_page was defined incorrectly.
The "vtl_control" should be u64[3], "nested_enlightenments
_control" should be a u64 and there are 7 reserved bytes
following "enlighten_vmentry". Fix the definition.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These MSRs should be enumerated by KVM_GET_MSR_INDEX_LIST, so that
userspace knows that these MSRs may be part of the vCPU state.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Eric Hankland <ehankland@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Obtain scale type through sysfs
- New Functionality
- Provide Device Tree functionality; rave-sp-backlight
- Calculate if scale type is (non-)linear; pwm_bl
- Fix-ups
- Simplify code; lm3630a_bl
- Trivial rename/whitespace/typo fixes; lms283gf05
- Remove superfluous NULL check; tosa_lcd
- Fix power state initialisation; gpio_backlight
- List supported file; MAINTAINERS
- Bug Fixes
- Kconfig - default to not building unless requested; {LED,BACKLIGHT}_CLASS_DEVICE
-----BEGIN PGP SIGNATURE-----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=DSnC
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Frameworks
- Obtain scale type through sysfs
New Functionality:
- Provide Device Tree functionality in rave-sp-backlight
- Calculate if scale type is (non-)linear in pwm_bl
Fix-ups:
- Simplify code in lm3630a_bl
- Trivial rename/whitespace/typo fixes in lms283gf05
- Remove superfluous NULL check in tosa_lcd
- Fix power state initialisation in gpio_backlight
- List supported file in MAINTAINERS
Bug Fixes:
- Kconfig - default to not building unless requested in
{LED,BACKLIGHT}_CLASS_DEVICE"
* tag 'backlight-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Set scale type for brightness curves specified in the DT
backlight: pwm_bl: Set scale type for CIE 1931 curves
backlight: Expose brightness curve type through sysfs
MAINTAINERS: Add entry for stable backlight sysfs ABI documentation
backlight: gpio-backlight: Correct initial power state handling
video: backlight: tosa_lcd: drop check because i2c_unregister_device() is NULL safe
video: backlight: Drop default m for {LCD,BACKLIGHT_CLASS_DEVICE}
backlight: lms283gf05: Fix a typo in the description passed to 'devm_gpio_request_one()'
backlight: lm3630a: Switch to use fwnode_property_count_uXX()
backlight: rave-sp: Leave initial state and register with correct device
response to mechanically detected potential issues. The remaining
patch cleans up kernel-doc notations.
-----BEGIN PGP SIGNATURE-----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=QV1S
-----END PGP SIGNATURE-----
Merge tag 'smack-for-5.4-rc1' of git://github.com/cschaufler/smack-next
Pull smack updates from Casey Schaufler:
"Four patches for v5.4. Nothing is major.
All but one are in response to mechanically detected potential issues.
The remaining patch cleans up kernel-doc notations"
* tag 'smack-for-5.4-rc1' of git://github.com/cschaufler/smack-next:
smack: use GFP_NOFS while holding inode_smack::smk_lock
security: smack: Fix possible null-pointer dereferences in smack_socket_sock_rcv_skb()
smack: fix some kernel-doc notations
Smack: Don't ignore other bprm->unsafe flags if LSM_UNSAFE_PTRACE is set
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
- Fix mobiveil inbound window CPU base address setup (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix the CPU base address setup in inbound window
- Propagate regulator_get_optional() errors so callers can distinguish
real errors from optional regulators that are absent (Thierry Reding)
- Propagate devm_of_phy_get() errors so callers can distinguish
real errors from optional PHYs that are absent (Thierry Reding)
- Add Andrew Murray as PCI native driver reviewer (Lorenzo Pieralisi)
* remotes/lorenzo/pci/misc:
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: iproc: Propagate errors for optional PHYs
PCI: histb: Propagate errors for optional regulators
PCI: armada8x: Propagate errors for optional PHYs
PCI: imx6: Propagate errors for optional regulators
PCI: exynos: Propagate errors for optional PHYs
PCI: rockchip: Propagate errors for optional regulators
- Add mediatek support for MT7629 (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Add controller support for MT7629
dt-bindings: PCI: Add support for MT7629
- Mark Layerscape endpoint BARs 2 and 4 as 64-bit (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP so EP/RC can be built separately (Xiaowei
Bao)
* remotes/lorenzo/pci/layerscape:
PCI: layerscape: Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC separately
PCI: layerscape: Add the bar_fixed_64bit property to the endpoint driver
- Fix Hyper-V use-after-free in pci_dev removal (Dexuan Cui)
- Fix Hyper-V build error in non-sysfs config (Randy Dunlap)
- Reallocate to avoid Hyper-V domain number collisions (Haiyang Zhang)
- Use Hyper-V instance ID bytes 4-5 to reduce domain collisions (Haiyang
Zhang)
* remotes/lorenzo/pci/hv:
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
PCI: hv: Detect and fix Hyper-V PCI domain number collision
PCI: pci-hyperv: Fix build errors on non-SYSFS config
PCI: hv: Avoid use of hv_pci_dev->pci_slot after freeing it
- Make kirin_dw_pcie_ops constant (Nishka Dasgupta)
- Make DesignWare "num-lanes" property optional and remove from relevant
DTs (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
arm64: dts: fsl: Remove num-lanes property from PCIe nodes
ARM: dts: ls1021a: Remove num-lanes property from PCIe nodes
PCI: dwc: Return directly when num-lanes is not found
dt-bindings: PCI: designware: Remove the num-lanes from Required properties
PCI: kirin: Make structure kirin_dw_pcie_ops constant
- Convert pci_resource_to_user() to a weak function to remove
HAVE_ARCH_PCI_RESOURCE_TO_USER #defines (Denis Efremov)
- Use PCI_SRIOV_NUM_BARS for idiomatic loop structure (Denis Efremov)
- Fix Resizable BAR size suspend/restore for 1MB BARs (Sumit Saxena)
- Correct "pci=resource_alignment" example in documentation (Alexey
Kardashevskiy)
* pci/resource:
PCI: Correct pci=resource_alignment parameter example
PCI: Restore Resizable BAR size bits correctly for 1MB BARs
PCI: Use PCI_SRIOV_NUM_BARS in loops instead of PCI_IOV_RESOURCE_END
PCI: Convert pci_resource_to_user() to a weak function
# Conflicts:
# drivers/pci/pci.c
- Cleanup pciehp LED/indicator control with a new consolidated
pciehp_set_indicators() interface that controls both Attention and
Power Indicators (Denis Efremov)
* pci/pciehp:
PCI: pciehp: Refer to "Indicators" instead of "LEDs" in comments
PCI: pciehp: Remove pciehp_green_led_{on,off,blink}()
PCI: pciehp: Remove pciehp_set_attention_status()
PCI: pciehp: Combine adjacent indicator updates
PCI: pciehp: Add pciehp_set_indicators() to set both indicators
- Use devm_add_action_or_reset() helper (Fuqian Huang)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Convert sysfs device attributes from __ATTR() to DEVICE_ATTR() (Kelsey
Skunberg)
- Convert sysfs file permissions from S_IRUSR etc to octal (Kelsey
Skunberg)
- Move SR-IOV sysfs functions to iov.c (Kelsey Skunberg)
- Add pci_info_ratelimited() to ratelimit PCI messages separately
(Krzysztof Wilczynski)
- Fix "'static' not at beginning of declaration" warnings (Krzysztof
Wilczynski)
- Clean up resource_alignment parameter to not require static buffer
(Logan Gunthorpe)
- Add ACS quirk for iProc PAXB (Abhinav Ratna)
- Add pci_irq_vector() and other stubs for !CONFIG_PCI (Herbert Xu)
* pci/misc:
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
PCI: Add ACS quirk for iProc PAXB
PCI: Force trailing new line to resource_alignment_param in sysfs
PCI: Move pci_[get|set]_resource_alignment_param() into their callers
PCI: Clean up resource_alignment parameter to not require static buffer
PCI: Use static const struct, not const static struct
PCI: Add pci_info_ratelimited() to ratelimit PCI separately
PCI/IOV: Remove group write permission from sriov_numvfs, sriov_drivers_autoprobe
PCI/IOV: Move sysfs SR-IOV functions to iov.c
PCI: sysfs: Change permissions from symbolic to octal
PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()
PCI: sysfs: Define device attributes with DEVICE_ATTR*()
PCI: Mark expected switch fall-through
PCI: Use devm_add_action_or_reset()
- Consolidate _HPP & _HPX code in pci-acpi.h and remove unnecessary
struct hotplug_program_ops (Krzysztof Wilczynski)
- Fixup PCIe device types to remove the need for dev->has_secondary_link
(Mika Westerberg)
* pci/enumeration:
PCI: Get rid of dev->has_secondary_link flag
PCI: Make pcie_downstream_port() available outside of access.c
PCI/ACPI: Remove unnecessary struct hotplug_program_ops
PCI/ACPI: Move _HPP & _HPX functions to pci-acpi.c
PCI/ACPI: Rename _HPX structs from hpp_* to hpx_*
- Move many symbols from public linux/pci.h to subsystem-private
drivers/pci/pci.h (Kelsey Skunberg)
- Unexport pci_bus_get() and pci_bus_sem since they're not needed by
modules (Kelsey Skunberg)
- Remove unused pci_block_cfg_access() et al (Kelsey Skunberg)
* pci/encapsulate:
PCI: Make pci_set_of_node(), etc private
PCI: Make pci_enable_ptm() private
PCI: Make pcie_set_ecrc_checking(), pcie_ecrc_get_policy() private
PCI: Make pci_ats_init() private
PCI: Make pcie_update_link_speed() private
PCI: Make pci_bus_get(), pci_bus_put() private
PCI: Make pci_hotplug_io_size, mem_size, and bus_size private
PCI: Make pci_save_vc_state(), pci_restore_vc_state(), etc private
PCI: Make pci_get_host_bridge_device(), pci_put_host_bridge_device() private
PCI: Make pci_check_pme_status(), pci_pme_wakeup_bus() private
PCI: Make PCI_PM_* delay times private
PCI: Unexport pci_bus_sem
PCI: Unexport pci_bus_get() and pci_bus_put()
PCI: Remove pci_block_cfg_access() et al (unused)
Pull livepatching fix from Jiri Kosina:
"Error handling fix in livepatching module notifier, from Miroslav
Benes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
livepatch: Nullify obj->mod in klp_module_coming()'s error path
Pull HID updates from Jiri Kosina:
- syzbot memory corruption fixes for hidraw, Prodikeys, Logitech and
Sony drivers from Alan Stern and Roderick Colenbrander
- stuck 'fn' key fix for hid-apple from Joao Moreno
- proper propagation of EPOLLOUT from hiddev and hidraw, from Fabian
Henneke
- fixes for handling power management for intel-ish devices with NO_D3
flag set, from Zhang Lixu
- extension of supported usage range for customer page, as some
Logitech devices are actually making use of it. From Olivier Gay.
- hid-multitouch is no longer filtering mice node creation, from
Benjamin Tissoires
- MobileStudio Pro 13 support, from Ping Cheng
- a few other device ID additions and assorted smaller fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (27 commits)
HID: core: fix dmesg flooding if report field larger than 32bit
HID: core: Add printk_once variants to hid_warn() etc
HID: core: reformat and reduce hid_printk macros
HID: prodikeys: Fix general protection fault during probe
HID: wacom: add new MobileStudio Pro 13 support
HID: sony: Fix memory corruption issue on cleanup.
HID: i2c-hid: modify quirks for weida's devices
HID: apple: Fix stuck function keys when using FN
HID: sb0540: add support for Creative SB0540 IR receivers
HID: Add quirk for HP X500 PIXART OEM mouse
HID: logitech-dj: Fix crash when initial logi_dj_recv_query_paired_devices fails
hid-logitech-dj: add the new Lightspeed receiver
HID: logitech-dj: add support of the G700(s) receiver
HID: multitouch: add support for the Smart Tech panel
HID: multitouch: do not filter mice nodes
HID: do not call hid_set_drvdata(hdev, NULL) in drivers
HID: wacom: do not call hid_set_drvdata(hdev, NULL)
HID: logitech: Fix general protection fault caused by Logitech driver
HID: hidraw: Fix invalid read in hidraw_ioctl
HID: wacom: support named keys on older devices
...
Pull SafeSetID fix from Micah Morton:
"Jann Horn sent some patches to fix some bugs in SafeSetID for 5.3.
After he had done his testing there were a couple small code tweaks
that went in and caused this bug.
From what I can see SafeSetID is broken in 5.3 and crashes the kernel
every time during initialization if you try to use it. I came across
this bug when backporting Jann's changes for 5.3 to older kernels
(4.14 and 4.19). I've tested on a Chrome OS device with those kernels
and verified that this change fixes things.
It doesn't seem super useful to have this bake in linux-next, since it
is completely broken in 5.3 and nobody noticed"
* tag 'safesetid-bugfix-5.4' of git://github.com/micah-morton/linux:
LSM: SafeSetID: Stop releasing uninitialized ruleset
-----BEGIN PGP SIGNATURE-----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=n4ht
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20190917' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
- Add LSM hooks, and SELinux access control hooks, for dnotify,
fanotify, and inotify watches. This has been discussed with both the
LSM and fs/notify folks and everybody is good with these new hooks.
- The LSM stacking changes missed a few calls to current_security() in
the SELinux code; we fix those and remove current_security() for
good.
- Improve our network object labeling cache so that we always return
the object's label, even when under memory pressure. Previously we
would return an error if we couldn't allocate a new cache entry, now
we always return the label even if we can't create a new cache entry
for it.
- Convert the sidtab atomic_t counter to a normal u32 with
READ/WRITE_ONCE() and memory barrier protection.
- A few patches to policydb.c to clean things up (remove forward
declarations, long lines, bad variable names, etc)
* tag 'selinux-pr-20190917' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
lsm: remove current_security()
selinux: fix residual uses of current_security() for the SELinux blob
selinux: avoid atomic_t usage in sidtab
fanotify, inotify, dnotify, security: add security hook for fs notifications
selinux: always return a secid from the network caches if we find one
selinux: policydb - rename type_val_to_struct_array
selinux: policydb - fix some checkpatch.pl warnings
selinux: shuffle around policydb.c to get rid of forward declarations
Pull crypto fixes froim Herbert Xu:
"This fixes the following issues:
- potential boot hang in hwrng
- missing switch/break in talitos
- bugs and warnings in hisilicon
- build warning in inside-secure"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon - avoid unused function warning
hwrng: core - don't wait on add_early_randomness()
crypto: hisilicon - Fix return value check in hisi_zip_acompress()
crypto: hisilicon - Matching the dma address for dma_pool_free()
crypto: hisilicon - Fix double free in sec_free_hw_sgl()
crypto: inside-secure - Fix unused variable warning when CONFIG_PCI=n
crypto: talitos - fix missing break in switch statement
- support for the Smart Tech panel, from Benjamin Tissoires
- hid-multitouch is no longer filtering mice node creation,
from Benjamin Tissoires
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- extension of supported usage range for customer page, as some Logitech
devices are actually making use of it. From Olivier Gay.
- support for Lightspeed and G700(s) receivers from Filipe Laíns and
Benjamin Tissoires
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Vitaly Kuznetsov