Commit Graph

34941 Commits

Author SHA1 Message Date
Larry Finger 013978b688 b43: Changes to enable BCM4311 rev 02 with wireless core revision 13
The BCM94311MCG rev 02 chip has an 802.11 core with revision 13 and
has not been supported until now. The changes include the following:

(1) Add the 802.11 rev 13 device to the ssb_device_id table to load b43.
(2) Add PHY revision 9 to the supported list.
(3) Change the 2-bit routing code for address extensions to 0b10 rather
    than the 0b01 used for the 32-bit case.
(4) Remove some magic numbers in the DMA setup.

The DMA implementation for this chip supports full 64-bit addressing with
one exception. Whenever the Descriptor Ring Buffer is in high memory, a
fatal DMA error occurs. This problem was not present in 2.6.24-rc2 due
to code to "Bias the placement of kernel pages at lower PFNs". When
commit 44048d70 reverted that code, the DMA error appeared. As a "fix",
use the GFP_DMA flag when allocating the buffer for 64-bit DMA. At present,
this problem is thought to arise from a hardware error.

This patch has been tested on my system and by Cédric Caumont
<icare40@hotmail.com>.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:05:01 -08:00
Stefano Brivio 00e0b8cb74 b43: reinit on too many PHY TX errors
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:05:01 -08:00
Johannes Berg d8be11ee95 b43: include FCS in frames handed to mac80211
Sometimes it can be useful to see the FCS, especially when
bad-FCS frames are shown. Pass the FCS to mac80211 and let
it worry about snipping it off when required.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:05:00 -08:00
Johannes Berg d42ce84a05 b43: include full 64-bit timestamp in monitor mode
When monitor mode is enabled, this will make b43 read out the
full 64-bit MAC time from the chip for each received packet.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:59 -08:00
Holger Schurig 0b3c07ff64 libertas: less eventcause shifts
* only shift eventcause once

* convert mac events to decimal, as this is what the firmware
  manual uses in section 6.1, too

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:58 -08:00
Holger Schurig a7d0adae40 libertas: remove user-specified channel list
Remove the ability to specify channels to scan via debugfs

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:58 -08:00
Holger Schurig dd1d12dabf libertas: remove numprobes
Remove the ability to specify number of probes via debugfs

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:57 -08:00
Holger Schurig 01affb6530 libertas: tweak tx path debugging
Make two functions in the TX packet path emit
their debug messages with LBS_DEB_TX, not LBS_DEB_MAIN.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:56 -08:00
Holger Schurig 91843463bc libertas: tweak association debug output
Change debug output codes from LBS_DEB_JOIN to LBS_DEB_ASSOC

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:55 -08:00
Holger Schurig 3a18864917 libertas: rework event subscription
This patch moves re-works the implementation of event subscription
via debugfs. For this:

* it tells cmd.c and cmdresp.c about CMD_802_11_SUBSCRIBE_EVENT
* removes lots of low-level cmd stuff from debugfs.c
* create unified functions to read/write snr, rssi, bcnmiss and
  failcount
* introduces #define's for subscription event bitmask values
* add a function to search for a specific element in an IE
  (a.k.a. TLV)
* add a function to find out the size of the TLV. This is needed
  because lbs_prepare_and_send_command() has an argument for a
  data buffer, but not for it's lengths and TLVs can be, by
  definition, vary in size.
* fix a bug where it was not possible to disable an event

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:55 -08:00
Holger Schurig 69f9032d9d libertas: remove arbitrary typedefs
New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv

While passing, make everything checkpatch.pl-clean that gets touches.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:54 -08:00
Brajesh Dave 96287ac4f7 libertas: configurable beacon interval
Requires firmware version 5.110.19.p0 or newer, available here:
http://dev.laptop.org/pub/firmware/libertas/

Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:53 -08:00
Brajesh Dave 01d77d8d47 libertas: separate mesh connectivity from that of the main interface
The transmit and receive traffic as soon as the mesh interface is
brought up.

Test case 1:  Bring up only the mesh interface and ping.  No need for
any iwconfig commands on the main interface.

$ ifconfig msh0 192.168.5.3
$ iwconfig msh0 channel X
$ ping 192.168.5.2
If ping succeeds, PASS

Test case 2:  Associate with the main interface, and turn off AP.  Mesh
interface should not lose connectivity.

$ iwconfig eth0 mode managed essid "my_ssid"
$ ifconfig msh0 192.168.5.3
$ ping 192.168.5.2
<turn off access point>
If ping continues uninterrupted, PASS

This feature requires firmware version 5.110.19.p0 or newer, available
here: http://dev.laptop.org/pub/firmware/libertas/

Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:52 -08:00
Andres Salomon 798fbfec9c libertas: nuke useless variable usbdriver_name and useless comments
I think it was pretty obvious what fields in if_usb_driver are...

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:51 -08:00
Andres Salomon be13f1897f libertas: reset devices upon disconnect rather than module unloading
1) Do not reset libertas devices upon module unload.  We're unloading
the module, we're not killing off devices.
2) Instead, reset libertas devices inside if_usb_disconnect, as we're
killing off interfaces and so on.
3) Resetting via disconnect callback means we no longer need to keep
track of probed libertas devices; kill off that list (and its wonderful
lack of locking..), as well.

Drop a useless comment as well.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:51 -08:00
Andres Salomon 4fb910fd3a libertas: mark module_init/exit functions as __init/__exit
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:50 -08:00
Andres Salomon 82209adcb1 libertas: drop useless default_fw_name variable
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:49 -08:00
Daniel Drake 66bb42fd47 zd1211rw: add copyright notices
Requested by Michael Wu.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:49 -08:00
Daniel Drake 269fca0edd zd1211rw: Add ID for Trendnet TEW-429UB A
Tested by chloubs on IRC
zd1211 chip 157e:300a v4810 high 00-11-e0 AL7230B_RF pa0 g----

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:48 -08:00
Daniel Drake 459c51ad6e zd1211rw: port to mac80211
This seems to be working smoothly now. Let's not hold back the mac80211
transition any further. This patch ports the existing driver from softmac
to mac80211.

Many thanks to everyone who helped out with the porting efforts.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:47 -08:00
Holger Schurig 0765af4493 libertas: clean up association debug messages
This makes the debug output of all association stuff clearer by:

* adding some lbs_deb_enter()/lbs_deb_leave() calls
* printing the return level in one place
* lower-casing some string

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:46 -08:00
Holger Schurig 1007832103 libertas: move to uniform lbs_/LBS_ namespace
This patch unifies the namespace of variables, functions defines
and structures. It does:

- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
  defined in libertas-local *.h files, e.g. not defines
  from net/ieee80211.h)

While passing, I fixed some checkpatch.pl errors too.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:46 -08:00
John W. Linville 9a62f73b1a iwlwifi: remove redundant initialization of final_mode
Problem identified by Miguel Botón <mboton.lkml@gmail.com>, alternate
solution suggested by Zhu Yi <yi.zhu@intel.com>, patch by me. :-)

Cc: Miguel Botón <mboton.lkml@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:45 -08:00
Larry Finger d3c319f9c8 ssb: Remove the old, now unused, data structures
The old, now unused, data structures and SPROM extraction routines
are removed.

Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:44 -08:00
Larry Finger 7797aa3848 b43legacy: Convert to use of the new SPROM structure
The b43legacy driver is modified to use the new SPROM structure.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:43 -08:00
Larry Finger 95de2841aa b43: Convert to use of the new SPROM structure
The b43 driver is modified to use the new SPROM structure.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:42 -08:00
Larry Finger 458414b2e3 b44: Convert to use of the new SPROM structure
The b44 driver is changed to use the new SPROM data structure.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:42 -08:00
Larry Finger c272ef4403 ssb: Convert to use of the new SPROM structure
In disagreement with the SPROM specs, revision 3 devices appear to have
moved the MAC address.

Change ssb to handle the revision 4 SPROM, which is a different size.
This change in size is handled by adding a new variable to the ssb_sprom
struct and using it whenever possible. For those routines that do not
have access to this structure, a 'u16 size' argument is added.

The new PCI_ID for the BCM4328 is also added.

Testing of the Revision 4 SPROM, which is used on the BCM4328, was done
by Michael Gerdau <mgerdau@tiscali.de>.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:41 -08:00
Larry Finger ac82fab44f ssb: Add new SPROM structure while keeping the old
The SPROM's for various devices utilizing the Sonics Silicon Backplane come
with various revisions. The Revision 2 SPROM inherited the data layout of 1, and
Revision 3 inherited the layout of 2. The first instance of Revision 4 has
now been found in a BCM4328 wireless LAN card. This device does not inherit any
layout from previous versions. Although it was possible to create a data
structure that kept all the old layouts, we decided to start fresh, keep only
those SPROM variables that are used by the drivers that utilize ssb, and to
do the conversion in such a manner that neither compilation or execution will
be affected if a bisection lands in the middle of these changes, while keeping
the patches as small as possible.

In this patch, the sprom structures are changed while maintaining the old ones.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:40 -08:00
Ivo van Doorn 3957ccb56e rt2x00: Move duplicate code into rt2x00pci_txdone()
rt2400pci, rt2500pci and rt61 require different
txdone handling, but the code that pushes the frame
upstream and cleans up the entry is identical to
all of them.
This will create the function rt2x00pci_txdone()
to remove the duplicate code.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:40 -08:00
Zhu Yi 797a54c68e iwl4965: fix rxon flags set to wrong value for A mode in .erp_ie_changed
The patch fixes a bug that enables RXON_FLG_TGG_PROTECT_MSK erroneously
for A mode in the erp_ie_changed mac80211 callback.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:39 -08:00
Frank Lichtenheld 7223e8d900 b43: silence a bogus gcc warning
use uninitialized_var() to avoid the following bogus warning:
  CC [M]  drivers/net/wireless/b43/debugfs.o
drivers/net/wireless/b43/debugfs.c: In function ‘b43_debugfs_read’:
drivers/net/wireless/b43/debugfs.c:355: warning: ‘ret’ may be used uninitialized in this function

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:38 -08:00
Stefano Brivio 59f1b15465 b43legacy: fix kconfig dependecies for rfkill and leds
Fix dependencies for built-in b43legacy.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:37 -08:00
Zhu Yi 4900d6daad remove unused iwl4965_init_hw_rates function
The patch removes the unused function to fix a recursive bug caused
by namespace change.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:35 -08:00
Christoph Hellwig bb8c093bde iwlwifi: cleanup namespace
Prefix all symbols with iwl3945_ or iwl4965_ and thus allow building
the driver into the kernel. Also remove all the useless default
statements in Kconfig while we're at it.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:04:35 -08:00
Mohamed Abbas 403ab56b1c iwl4965: fix cannot find a suitable rate issue
This patch fixes the iwl4965 problem for "Can not find a suitable rate
issues." by making rs_switch_to_mimo and rs_switch_to_siso functions
return -1 when CONFIG_IWL4965_HT is not selected. They used to return 0,
which means we can switch to HT rate causing the rate scale problem and
the error message.

The patch also fix another bug reported by Ben Cahill that it uses wrong
value for max_success_limit.

Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:33 -08:00
Zhu Yi 3567c11d72 iwlwifi: replace 0x8086 with PCI_VENDOR_ID_INTEL
Replace 0x8086 with PCI_VENDOR_ID_INTEL for PCI_DEVICE declaration.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:32 -08:00
Stefano Brivio 1f21ad2a4f b43/b43legacy: fix my copyright notices
Fix my copyright notices in b43 and b43legacy.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:31 -08:00
Stefano Brivio 61bca6eb85 b43: rewrite A PHY initialization
Rewrite and sync A PHY initialization with specs, thus allowing for further
work to be done on 802.11a support. Note that A PHY initialization involves
G PHYs as well.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:31 -08:00
Stefano Brivio db9683fb19 b43legacy: rewrite and fix rfkill initialization
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */

This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up

Fix this by always re-allocating the rfkill stuff before register.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:30 -08:00
Stefano Brivio 33a3dc9328 b43legacy: use a consistent naming scheme for the ops
Use a consistent naming scheme for the ops.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:29 -08:00
Stefano Brivio 0a6e1bee57 b43legacy: use the retry limits provided by mac80211
Use the retry limits provided by mac80211.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:28 -08:00
Thomas Bogendoerfer 43831b1581 SGISEEQ: use cached memory access to make driver work on IP28
SGI IP28 machines would need special treatment (enable adding addtional
wait states) when accessing memory uncached. To avoid this pain I changed
the driver to use only cached access to memory.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:28 -08:00
Olof Johansson b0cd2f9016 pasemi_mac: Don't enable RX/TX without a link (if possible)
pasemi_mac: Don't enable RX/TX without a link (if possible)

Don't enable RX/TX of packets until we have a link, since there's a chance
we'll just get RX frame errors, etc.

The case where we don't have a PHY we can't do much about: Just enable
it and deal with errors as they come in.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:27 -08:00
Olof Johansson 8304b633c5 pasemi_mac: Print warning when not attaching to a PHY
pasemi_mac: Print warning when not attaching to a PHY

Print a warning on the console when not connecting to a phy for an interface.
It turns out to be a pretty common problem when someone gets the MDIO info
wrong in their device tree, resulting in the macs running at a fixed 1Gbit FD.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:26 -08:00
Olof Johansson 5d8949448b pasemi_mac: Remove SKB copy/recycle logic
pasemi_mac: Remove SKB copy/recycle logic

It doesn't really buy us much, since copying is about as expensive
as the allocation in the first place. Just remove it for now.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:26 -08:00
Olof Johansson 7e9916e9dd pasemi_mac: SKB unmap optimization
pasemi_mac: SKB unmap optimization

Avoid touching skb_shinfo() in the unmap path, since it turns out to
normally cause cache misses and delays. instead, save number of fragments
in the TX_RING_INFO structures since that's all that's needed anyway.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:25 -08:00
Olof Johansson 28ae79f531 pasemi_mac: Software-based LRO support
pasemi_mac: Software-based LRO support

Implement LRO for pasemi_mac. Pretty straightforward.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:24 -08:00
Olof Johansson 906674abab pasemi_mac: Improve RX interrupt mitigation
pasemi_mac: Improve RX interrupt mitigation

Currently the receive side interrupts will go off on the reception of
a packet, NAPI will poll the ring and keep polling as long as there's
a decent amount of packets to receive.

This is less than optimal, especially for LRO where it's better if we
have a more substantial amount of packets to process at once, to get
the real LRO benefits.

So, set the count threshold to a higher value and use the timeout feature
that will give us an interrupt even if not enough packets have come in
to set off the count threshold.

FIXME: It'd be real nice to have ethtool support for users to tune this
at runtime.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:24 -08:00
Olof Johansson 61cec3bddc pasemi_mac: Fix TX cleaning
pasemi_mac: Fix TX cleaning

This is a bit awkward. We don't have a timer-delayed interrupt on TX
complete, but we have a count threshold. So set that reasonably high
(32 packets), and schedule the NAPI poll when it goes off. Also bump a
regular timer that will take care of rotting packets for the last 1..31
ones in case we don't trigger a TX interrupt (and there's no RX activity
that would otherwise trigger the poll).

The longer-term fix is to separate TX from RX NAPI and do two separate
poll loops.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:23 -08:00
Olof Johansson 5c15332bed pasemi_mac: performance tweaks
pasemi_mac: performance tweaks

* Seems like we do better with a smaller RX ring, probably because chances of
  still having the SKB cached are better
* Const-ify variables to get better code generation and fewer reloads
* Move prefetching around a little, and try to prefetch the whole SKB
* Set NETIF_F_HIGHDMA
* Misc other minor tweaks

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:22 -08:00
Olof Johansson 34c20624ce pasemi_mac: Convert to new dma library
pasemi_mac: Convert to new dma library

Convert the pasemi_mac driver to the new platform global DMA manaagement
library. This also does a couple of other minor cleanups w.r.t. channel
management.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:21 -08:00
Olof Johansson 40afa53158 pasemi_mac: Move register definitions to include/asm-powerpc
pasemi_mac: Move register definitions to include/asm-powerpc

Move the common register formats and descriptor layouts from
drivers/net/pasemi_mac.h to include/asm-poewrpc/pasemi_dma.h

Previously only the ethernet driver was using them, but other drivers
are coming up that will also use them, so it makes sense to share the
constants.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:20 -08:00
Olof Johansson 72b05b9940 pasemi_mac: RX/TX ring management cleanup
pasemi_mac: RX/TX ring management cleanup

Prepare a bit for supporting multiple TX queues by cleaning up some
of the ring management and shuffle things around a bit.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:19 -08:00
Stephen Hemminger 5f06eba4dc sky2: rx allocation threshold change
When using larger MTU's sky2 driver changes from allocating one
data area, to using multiple pages. The threshold for this was based on
a heuristic where the cost of a single allocation is bigger than one
page.  Since the allocator has changed, this heuristic is now incorrect;
instead just make the threshold be when the total size of the allocation
is greater than one page.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:19 -08:00
Stephen Hemminger f03b865491 sky2: align IP header on Rx if possible
The sky2 driver was not aligning the IP header on receive buffers.
This workaround is only needed on hardware with broken FIFO, newer chips
without FIFO can just DMA to unaligned address.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:18 -08:00
Francois Romieu 5ac5d61632 r6040: cleanups
- whitespaces vs tabs
- use 80 cols
- use if_mii
- use netdev_priv
- remove useless cast to void *
- PCI device id does not need to be globally available

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2008-01-28 15:04:16 -08:00
Francois Romieu e6a9ea1052 r6040: erroneous dev->priv
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2008-01-28 15:04:16 -08:00
Francois Romieu 6c3231035d r6040: remove virt_to_bus
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2008-01-28 15:04:15 -08:00
Francois Romieu 5125a78668 r6040: compile error
drivers/net/r6040.c: In function 'rx_buf_alloc':
drivers/net/r6040.c:262: warning: passing argument 2 of 'pci_map_single' makes pointer from integer without a cast

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2008-01-28 15:04:14 -08:00
Komuro bd5a934620 axnet_cs: use spin_lock_irqsave instead of spin_lock + disable_irq
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:14 -08:00
Jeff Garzik 2eab17ab88 drivers/net/cxgb3: trim trailing whitespace
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:04:13 -08:00
Divy Le Ray afefce66a5 cxgb3 - Fix I/O synchronization
Synchronize memory access before ringing
the Tx door bell.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:12 -08:00
Divy Le Ray a2604be548 cxgb3 - HW set up updates
Disable PEX errors. The HW generates false positives.
Update RSS hash function to a symmetric algorithm.
Update T3C HW support

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:11 -08:00
Divy Le Ray 3e5192eec8 cxgb3 - sysfs methods clean up
Remove unused argument in sysfs methods

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:10 -08:00
Divy Le Ray 23561c9447 cxgb3 - fix interaction with pktgen
Do not use skb->cb to stash unmap info,
save the info to the descriptor state.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:09 -08:00
Divy Le Ray 273fa9042c cxgb3 - FW upgrade
Bump up FW version to 5.0.
Do not downgrade FW within the same major version range.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:09 -08:00
Divy Le Ray 91a6b50cf6 cxgb3 - Add EEH support
Add PCI recovery support

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:08 -08:00
Divy Le Ray 67d92ab765 cxgb3 - Fix resources release.
Remove sysfs entries before unregistering the net devices.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:07 -08:00
Divy Le Ray 678771d6f5 cxgb3 - Use wild card for PCI subdevice ID match
Subdevice ID is not necessarily set to 1.
Use wild card for PCI device matching

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:07 -08:00
Divy Le Ray 42256f57d8 cxgb3 - fix MSI-X failure path
Return error code when msi-x settings fail.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:06 -08:00
Jeff Garzik cba0516ddb [netdrvr] checkpatch cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:04:05 -08:00
Jeff Garzik 93a3b607e6 wireless: checkpatch cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:04:04 -08:00
Jeff Garzik 092427be8c drivers/net/r6040: fix obvious problems (but more remain)
- checkpatch fixes

- fix bogus and uninitialized return codes in r6040_start_xmit()

- netdev_get_settings() fix obvious locking bug flagged by compiler warning

- set DMA consistent mask

- remove unnecessary setting of dev->base_addr

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:04:03 -08:00
Jeff Garzik 4790654c71 [netdrvr] netxen: checkpatch fixes (98% trim trailing whitespace)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:04:02 -08:00
Peter Korsgaard ba734f349d dm9601: Consolidate common parts of dm_write_*_async
dm_write_async and dm_write_reg_async are almost identical.
Move common functionality to dm_write_async_helper (saves ~256b).

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:01 -08:00
Alan Cox 9ce6cf2553 slip: Drag kicking and screaming into coding style compliance
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:01 -08:00
Alan Cox a35f5de776 3c501: Bring into compliance with the coding style
3c501 leads the way... 8)

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:00 -08:00
Adrian Bunk 68d579fb93 drivers/net/chelsio/: #if 0 unused functions
This patch #if 0's the following unused functions:
- espi.c:t1_espi_set_misc_ctrl()
- sge.c:t1_sched_set_max_avail_bytes()
- sge.c:t1_sched_set_drain_bits_per_us()

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:59 -08:00
Joe Perches 2450022afa drivers/net: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:59 -08:00
Joe Perches 60403fdada drivers/net/sk98lin: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:58 -08:00
Joe Perches 93ab8e84de drivers/net/wan: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:57 -08:00
Joe Perches 5bc51424b4 drivers/net/netxen: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:56 -08:00
Joe Perches 8c5863a406 drivers/net/ixgb: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:55 -08:00
Joe Perches f07b2e403b drivers/net/cxgb3: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:55 -08:00
Joe Perches 3106752768 drivers/net/chelsio: Add missing "space"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:54 -08:00
Eliezer Tamir a2fbb9ea23 add bnx2x driver for BCM57710
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:53 -08:00
Sreenivasa Honnur faa4f7969f [S2IO]: Support for add/delete/store/restore ethernet addresses
- Support to add/delete/store/restore 64 and 128 Ethernet addresses for Xframe I and Xframe II respectively.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:52 -08:00
Patrick McHardy db0ce50d37 [E1000]: Secondary unicast address support
Add support for configuring secondary unicast addresses. Unicast
addresses take precendece over multicast addresses when filling
the exact address filters to avoid going to promiscous mode.
When more unicast addresses are present than filter slots,
unicast filtering is disabled and all slots can be used for
multicast addresses.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:51 -08:00
Joe Perches 2a88719197 [E1000E]: convert register test macros to functions
Add functions for reg_pattern_test and reg_set_and check
Changed macros to use these functions

Compiled x86, untested

Size decreased ~2K

old:

$ size drivers/net/e1000e/ethtool.o
   text    data     bss     dec     hex filename
  14461       0       0   14461    387d drivers/net/e1000e/ethtool.o

new:

$ size drivers/net/e1000e/ethtool.o
   text    data     bss     dec     hex filename
  12498       0       0   12498    30d2 drivers/net/e1000e/ethtool.o

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:51 -08:00
Joe Perches 7e64300a0f [E1000]: Convert regtest macro's to functions
Minimal macro to function conversion in e1000_ethtool.c

Adds functions reg_pattern_test and reg_set_and_check
Changes REG_PATTERN_TEST and REG_SET_AND_CHECK macros
to call these functions.

Saves ~2.5KB

Compiled x86, untested (no hardware)

old:

$ size drivers/net/e1000/e1000_ethtool.o
   text    data     bss     dec     hex filename
  16778       0       0   16778    418a drivers/net/e1000/e1000_ethtool.o

new:

$ size drivers/net/e1000/e1000_ethtool.o
   text    data     bss     dec     hex filename
  14128       0       0   14128    3730 drivers/net/e1000/e1000_ethtool.o

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:50 -08:00
Auke Kok ef90e4eca9 [E1000]: update netstats traffic counters realtime
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:49 -08:00
Auke Kok 4198869277 [E1000E]: update netstats traffic counters realtime
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:49 -08:00
Sten Wang 7a47dd7a2f [NET]: Add support for the RDC R6040 Fast Ethernet controller
This patch adds support for the RDC R6040 MAC we can find in the RDC
R-321x System-on-chips.

Signed-off-by: Sten Wang <sten.wang@rdc.com.tw>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
2008-01-28 15:03:47 -08:00
David Acker 7734f6e6bc Fix e100 on systems that have cache incoherent DMA
On the systems that have cache incoherent DMA, including ARM, there
is a race condition between software allocating a new receive buffer
and hardware writing into a buffer.  The two race on touching the last
Receive Frame Descriptor (RFD).  It has its el-bit set and its next
link equal to 0.  When hardware encounters this buffer it attempts to
write data to it and then update Status Word bits and Actual Count in
the RFD.  At the same time software may try to clear the el-bit and
set the link address to a new buffer.

Since the entire RFD is once cache-line, the two write operations can
collide.  This can lead to the receive unit stalling or interpreting
random memory as its receive area.

The fix is to set the el-bit on and the size to 0 on the next to last
buffer in the chain.  When the hardware encounters this buffer it stops
and does not write to it at all.  The hardware issues an RNR interrupt
with the receive unit in the No Resources state.  Software can write
to the tail of the list because it knows hardware will stop on the
previous descriptor that was marked as the end of list.

Once it has a new next to last buffer prepared, it can clear the el-bit
and set the size on the previous one.  The race on this buffer is safe
since the link already points to a valid next buffer and the software
can handle the race setting the size (assuming aligned 16 bit writes
are atomic with respect to the DMA read). If the hardware sees the
el-bit cleared without the size set, it will move on to the next buffer
and skip this one.  If it sees the size set but the el-bit still set,
it will complete that buffer and then RNR interrupt and wait.

Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:46 -08:00
Francois Romieu 3627947e84 sundance: SIOCDEVPRIVATE pollution
To quote one of my favorite contemporary author:
[include/linux/sockios.h]
 *      THESE IOCTLS ARE _DEPRECATED_ AND WILL DISAPPEAR IN 2.5.X -DaveM
 */

#define SIOCDEVPRIVATE  0x89F0  /* to 89FF */

[...]

Gentoo's snmpd trips up over this code when trying to figure if the driver
supports the non-SIOCDEVPRIVATE API or not.  One can argue over its choice
of heuristic but there no reason to make ioctl more ugly than needed.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Tested-by: Volker Sauer <vsauer@dvs.tu-darmstadt.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:46 -08:00
Adrian Bunk 993fb90c5b drivers/net/netxen/: cleanups
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:45 -08:00
Auke Kok 3957d63da0 ixgbe: Fix copper PHY initialization code
While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.

This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:44 -08:00
Auke Kok 040babf9d8 e1000/e1000e: Move PCI-Express device IDs over to e1000e
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.

This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.

Here is a brief list of which gigabit driver to use with which
adapter:

  e1000:
	82540 -> 82547

  e1000e:
	82571 -> 82573
	ich8, ich9       (82562 or 82566)
	es2lan           (80003eslan)

  igb: (not yet merged, only available from e1000.sf.net)
	82575

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:43 -08:00
Auke Kok 1eae4eb2a1 e1000e: Disable L1 ASPM power savings for 82573 mobile variants
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
 - eeprom reads return garbage information leading to bad eeprom
   checksums
 - long ping times (up to 2 seconds)
 - complete system hangs (freeze/lockup)

A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.

Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.

Remove a workaround RDTR adjustment that is no longer needed with
this new one.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:43 -08:00
Bill Hayes 93ca161027 e1000e: alternate MAC address support
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.

Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:42 -08:00
Jeff Garzik 3df5920c46 [netdrvr] ibmlana: move away from legacy MCA API
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:03:41 -08:00
Jeff Garzik fbe02d6d87 [netdrvr] ibmlana: modularization cleanup
* move alloc_netdev() call, register_netdev() call, and associated failure
  cleanup into ibmlana_probe()

* move per-net_device cleanup into ibmlana_remove_one()

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:03:40 -08:00
Jeff Garzik 28fc1f5a0c [netdrvr] irq handler minor cleanups in several drivers
* use irq_handler_t where appropriate

* no need to use 'irq' function arg, its already stored in a data struct

* rename irq handler 'irq' argument to 'dummy', where the function
  has been analyzed and proven not to use its first argument.

* remove always-false "dev_id == NULL" test from irq handlers

* remove pointless casts from void*

* declance: irq argument is not const

* add KERN_xxx printk prefix

* fix minor whitespace weirdness

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:03:40 -08:00
Jeff Garzik 1b36efe07f hamradio/scc: kill unnecessary use of 'irq' function arg
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-28 15:03:39 -08:00
Alejandro Martinez Ruiz ef878b8899 sk98lin: kill bogus check and convert to use ARRAY_SIZE()
This converts uses of ARRAY_SIZE(), and while at it also kills
unreachable code as far as I can say. I can't tell what was the author
trying to do with the following check. First we have:

PNMI_STATIC const SK_PNMI_STATADDR
		StatAddr[SK_PNMI_MAX_IDX][SK_PNMI_MAC_TYPES];

and then a check goes like this:

if (SK_PNMI_MAX_IDX !=
   (sizeof(StatAddr) / (sizeof(SK_PNMI_STATADDR) * SK_PNMI_MAC_TYPES)))

with the second line being just ARRAY_SIZE(StatAddr), which will always
return SK_PNMI_MAX_IDX, rendering the check useless.

Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:38 -08:00
Alejandro Martinez Ruiz c00acf46de netdev: ARRAY_SIZE() cleanups
Convert array size calculations to use ARRAY_SIZE().

Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:37 -08:00
Alejandro Martinez Ruiz 4c3616cdda netdev: use ARRAY_SIZE() instead of sizeof(array) / ETH_GSTRING_LEN
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.

Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:03:36 -08:00
Roel Kluin f59d978275 wireless: fix '!x & y' typo's
Fix priority mistakes similar to '!x & y'

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:35 -08:00
Holger Schurig 9f9dac281b libertas: move wlan_*_association_work from header to c file
Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.

Renamed those two functions to to libertas_XXX as well.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:34 -08:00
Jes Sorensen 49df2b3347 iwlwifi: disable interrupts before calling request_irq
Disable interrupts in the iwl4965 before calling request_irq() for
the case that the previous OS or the BIOS left a pending interrupt in
the chip. This behavior has been observed on some laptops such as T61
Thinkpads and Toshiba Portege R500

Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:34 -08:00
Dmitry Torokhov eb76bf29dd P54: use temporary variables to reduce size of generated code
When there are 2 linked structures, using a temporary variable to hold a pointer
to the often used structure usually produces better code (smaller and faster)
since compiler does not have to constantly re-fetch data from the first structure.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:33 -08:00
Matthias Kaehlcke 1b34fd390c Prism54: Convert mgmt_sem to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:32 -08:00
Dan Williams 1e3428e9e3 orinoco: more reliable scan handling
Bring scan result handling more in line with drivers like ipw.  Scan
results are aggregated and a BSS dropped after 15 seconds if no beacon
is received.  This allows the driver to interact better with userspace
where more than one process may request scans or results at any time.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:32 -08:00
Michael Buesch 40faacc407 b43: consistent naming for ieee80211_ops
Use a consistent naming scheme for the ops.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:31 -08:00
Michael Buesch 74cfdba7ce b43: Use the retry limit parameters from mac80211
Use the limits provided by mac80211.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:30 -08:00
Michael Buesch c6dfc9a8ec b43: Dereference of wl->current_dev must be protected by wl->mutex
Put all access to wl->current_dev under protection of the mutex.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:30 -08:00
Michael Buesch 0c1d379d2e b43legacy: Remove set_key callback
We don't need the set_key callback, as we don't do hw crypto.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:29 -08:00
Larry Finger f34eb692ac b43legacy: Rewrite pwork locking
Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.

This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.

Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:28 -08:00
Larry Finger 6be50837e3 b43legacy: Use input-polldev for the rfkill switch
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.

This patch is the port to b43legacy of a patch for b43 by Michael Buesch
<mb@bu3sch.de>.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:27 -08:00
Larry Finger 93bb7f3a7b b43legacy: RF-kill support
This adds full support for the RFKILL button and the RFKILL LED trigger.

This is a port to b43legacy of a patch by Michael Buesch <mb@bu3sch.de>
for b43.

Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:27 -08:00
Larry Finger ba48f7bb80 b43legacy: LED triggers support
Drive the LEDs through the generic LED triggers.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to b43legacy.

Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:26 -08:00
Christoph Hellwig c8b0e6e19c iwlwifi: cleanup Kconfig and ifdefs to split 3945 and 4965
Currently the iwl3945 & iwl4965 drivers share some common Kconfig
symbols.  This split it up into options for the individual drivers
and gets rid of all the CONFIG_IWLWIFI cruft.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:25 -08:00
Christoph Hellwig 5d08cd1dfd iwlwifi: keep 3945 and 4965 headers separate
The iwl3945 and iwl4965 devices share some common structure, but with a
lot of difference split all over.  Currently the two drivers share a lot
of headers and use ugly preprocessor magic to manage the difference.

This patch keeps two entirely separate copies of the headers to get rid
of these hacks an ease future development.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:24 -08:00
Christoph Hellwig 416e1438d5 iwlwifi: mark more functions/variables static
mark more functions/variables static

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:23 -08:00
Zhu Yi 80f3e024dc iwlwifi: Update iwlwifi version stamp to 1.1.19
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:22 -08:00
Zhu Yi 6ff7520933 iwlwifi: Update iwlwifi version stamp to 1.1.18
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:22 -08:00
mabbas bee488dbd7 iwl4965: exclude 60M rate from probe request
This patch do the following 2 things:
1. Make sure we don't add rate 60M part of supported rate in proble request,
   some AP does not like that.
2. It is wrong to set priv->active_rate in this function, this will set
   it to all avialable rates which might overwrite the mode supported rate.
   priv->active_rate should be set by only from iwl_set_rate.

Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:21 -08:00
Tomas Winkler d9fd0c9969 iwlwifi: Renames struct fw_image_desc to struct fw_desc
This patche shortens the name of struct fw_image_desc to be struct
fw_desc.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:20 -08:00
Emmanuel Grumbach b559e66cfc iwlwifi: add 5965 SCD registers to iwl-prph.h
This patch adds SCD registers for 5965

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:20 -08:00
Emmanuel Grumbach 7088310908 iwlwifi: move 3945 SCD registers to iwl-prph.h
This patch moves 3945 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:19 -08:00
Emmanuel Grumbach 67dc320d47 iwlwifi-ht: move 4965 SCD registers to iwl-prph.h
This patch moves 4965 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:18 -08:00
Tomas Winkler ac17a947a4 iwlwifi: replacing wording restricted to nic access in iwl-io
This patch replaces wording 'restricted' with more appropriate 'nic access'
NIC access is grabbed to prevent NIC entering power save mode
General cleanup of iwl-io.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:17 -08:00
Tomas Winkler af7cca2a44 iwlwifi: rename restricted_mem to targ_mem
This patch renames restricted_mem suffix with more proper
name targ_mem for function accessing memory on the nic in target mode

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:17 -08:00
Tomas Winkler d860965200 iwlwifi: replace restricted_reg with prph
This patch renames restricted_reg suffix with more proper
name prhp for function accessing registers on the periphery bus.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:16 -08:00
mabbas a033f37ee4 iwlwifi: accept up to 4K frame size on Rx side to fit A-MSDU frame
The driver drops any Rx frame larger than 2332 bytes, but with A-MSDU
frame, it could be up to 4K. This patch makes sure we can process larger
A-MSDU frame.

Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:15 -08:00
Tomas Winkler c6f3f656e1 iwlwifi: using PCI_DEVICE macro
PCI_DEVICE macro is more concise when using defualt values
in device definitions

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:14 -08:00
Tomas Winkler 12a70fbe57 iwlwifi: remove cck_power_index_compensation
cck_power_index_compensation variable was never used

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:13 -08:00
Ian Schram 3edb059a40 iwlwifi: remove late null-check and duplicate bug_on
These pieces of code appear to be useless. The BUG_ON is also performed in
iwl_send_cmd_async.

Serious karma would be needed to enter iwl_ativate_qos with a null priv.
I had a deja vu when patching this, but for the life of me I couldn't track
down a similar patch.

Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:13 -08:00
Ian Schram bc434dd296 iwlwifi: Beautify by removing superfluous newlines and code
Moving code around, lindent, and whatnot created several places where
there appeared to be an 75 column "rule" instead of 80. This patch removes
those that I can spot, hopefully increasing readability.

Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:12 -08:00
Ian Schram bbc5807bed iwlwifi: Two comments in iwl-3945.c were longer than 80 columns
This patch shorten two comments lines in iwl-3945.c

Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:11 -08:00
Tomas Winkler 6994633357 iwlwifi: remove cck_flag from iwl_driver_hw_info
This patch remove cck_flag from iwl_driver_hw_info, this flag
is unused after spliting the iwl-base.c

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:11 -08:00
Tomas Winkler f1f1f5c730 iwlwifi: add TGN flag to qos parameters
This patch adds TGN flag to QoS parameters. This flag governs enablement of
NAV shortening with CF-End and filters in 4 or 8K RX AMSDU packets

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:10 -08:00
Tomas Winkler dc2453ae81 iwlwifi: rs-4965 fix return values
This patch cleans up style of 'return' of rate scale 4965 functions.
It renames return name variables rc to ret, change functions to void if no
meaningful value was returned it add return of -EINVAL for checks of wrong
arguments.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:09 -08:00
Tomas Winkler fc4b6853fb iwlwifi: renaming last_used and first_empty
This patch renames queue pointers to write_ptr and read_ptr
instead of  first_empty and last_used. This is closer to technical
terminology we everyday use

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:08 -08:00
Ian Schram 91e1747384 iwlwifi: rename iwl_eeprom_aqcuire_semaphore to _acquire_
Correct the spelling of aqcuire.

Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:07 -08:00
Ian Schram 01ebd063e1 iwlwifi: fix various spelling and typos
Fixing various spelling errors and typos. Mostly in comments. In total
27 words were corrected, some of which occurred more than ones.

Signed-Of-By: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:06 -08:00
Tomas Winkler 220173b012 iwlwifi: Add erp_ie_changed hanlder
This patch adds erp_ie_changed handler to iwl4956

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:03:05 -08:00
Ivo van Doorn a3c7aa58df rt2x00: Release rt2x00 2.0.12
Version bump.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:05 -08:00
Mattias Nissler 2700f8b048 rt2x00: Correctly set ACK bit in tx descriptors
Add a flag to struct txdata_entry_desc that specifies whether an ack for the
frame is to be expected. Use this flag to set the ACK bit in the tx descriptor.
Previously, the ACK bit could be set incorrectly on CTS-to-self frames, so they
caused retries and were reported to be failed in the txdone handlers.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:04 -08:00
Adam Baker 3d82346c5d rt2x00: Place mutex around USB register access
There is a buffer, csr_cache which is used to hold copies of data being passed
to the USB stack which can get corrupted if multiple threads attempt to access
CSR registers simultaneously. There is also the possibility if multiple
threads try to access BBP or RF registers for the multiple USB operations
needed to get interleaved leading to incorrect results. This patch introduces
a mutex to prevent such simultaneous access. The interleaved access problem
may also affect the PCI devices but if so that will be handled in a follow-up
patch.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:03 -08:00
Ivo van Doorn 4bd7c452a4 rt2x00: Remove data_desc structure
Coverty indicated that data_desc with a single
element array is bad coding style. This removes
the structure and forces everybody to use __le32.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:03 -08:00
Mattias Nissler 2676c94d4e rt2x00: Rework rt73 antenna selection
This patch changes rt73 antenna selection to what I believe is the correct way.
It also fixes a small selection bug that switched the antennas by accident.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:01 -08:00
Ivo van Doorn 50794638dc rt2x00: Remove unused variables
With the updated antenna setup the following
variables are no longer used.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:01 -08:00
Mattias Nissler acaa410d06 rt2x00: Rework rt61 antenna selection.
This patch changes rt61 antenna selection again. It helps at least with the
rt61 pci card in my box, I hope I haven't broken behaviour on other RF chips.
RF 2529 antenna setup is incomplete, we need to at code for diversity when we
figure out how it is done properly.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:00 -08:00
Adam Baker 0e14f6d3e0 rt2x00: Unconstify rt2x00dev
Some register accesses need rt2x00dev to be non-const
they all need modifying so the prototype is consistent.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:59 -08:00
Ivo van Doorn d9890b8f45 rt2x00: Detect initial rfkill state on register
When registering rfkill, make sure a initial
poll event is directly executed to detect the initial
rfkill state and send the event to the rfkill layer.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:58 -08:00
Ivo van Doorn 4300beb47d rt2x00: Input-polldev requires input device
input-polldev requires a correctly allocated
and initialized input device to be set for the
input_polled_dev->input field.
Failure to do that will prevent correct polling
of the device.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:58 -08:00
Ivo van Doorn e4cd2ff89f rt2x00: Split rt61/rt73 antenna selection into RX and TX antenna
Based on investigation of the legacy drivers, I have made the
following assumptions of the antenna setup:
 - R77 is the TX antenna configuration
 - RF2529 fetches default antenna selection from NIC eeprom word

With these assumptions we can change the antenna configuration
to correctly read both antenna setup values and correctly
configure the antenna. And we can now also configure the antenna
for RF2529 without a double antenna.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:57 -08:00
Ivo van Doorn e25c4bb913 rt2x00: Disable RX when switching antenna
Antenna switching will be ignored when RX is enabled
during the switch. Make sure we disable the RX during
the switch and don't forget to reenable it later.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:56 -08:00
Ivo van Doorn 2d68de3efa [PATCH] rt2x00: Release rt2x00 2.0.11
Version bump.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:55 -08:00
Mattias Nissler 16b1951f53 [PATCH] rt2x00: Fix antenna selection.
In the config() handler, make sure that we do configure an antenna if the
current active antenna is uninitialized. Furthermore, don't overwrite the
active antenna with bogus values if we didn't touch the antenna setup.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:54 -08:00
Ivo van Doorn ddc827f93a [PATCH] rt2x00: Cleanup if-statements
Cleanup if-statements for simple 1/0 register field values.

This also fixes a endian bug in rt2500usb when working
with the PHY_CSR2 initialization. As well as a bug
in the enabling of the LED in rt73usb.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:54 -08:00
Ivo van Doorn 69f81a2cac [PATCH] rt2x00: Implement SW diversity
When mac80211 indicates that the default antenna setup
should be used _and_ that this default setup is SW_DIVERSITY.

This requires sampling and storing the RSSI per antenna
and check once every 2 seconds to determine if the RSSI
has changed significantly. Once this is the case we should sample
the other antenna for a short period and evaluate if
we need to swap antenna or not.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:53 -08:00
Ivo van Doorn 8de8c5162b [PATCH] rt2x00: Remove rt2x00_clear_link
rt2x00_clear_link() was becoming too large for statically inline,
also it was used on a single location and shouldn't really be
used anywhere else. So move the entire code into the function
rt2x00lib_start_link_tuner()

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:52 -08:00
Ivo van Doorn 39e75857d0 [PATCH] rt2x00: SW diversity should default to antenna B
Although ANTENNA_SW_DIVERSITY should never be send
to the driver, we should still handle it to prevent bugs.
But instead of defaulting to ANTENNA_HW_DIVERSITY we
should default to ANTENNA_B instead.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:52 -08:00
Ivo van Doorn addc81bd42 [PATCH] rt2x00: Correctly translate mac80211 antenna setup to rt2x00
mac80211 has 3 values for the antenna setup:
 0 - default
 1 - use antenna 1
 2 - use antenna 2

This means that rt2x00 should store the default value
from the EEPROM somwhere and use that when mac80211 indicates
that the antenna setup is 0.
This also implies that rt2x00 should no longer write the
hw->config.antenna_sel_* values based on the EEPROM input.

This also adds the basis in rt2x00lib for correct software
diversity handling. By default rt2x00lib will now configure
antenna B instead of hardware diversity.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:51 -08:00
Ivo van Doorn 362f3b6bfb [PATCH] rt2x00: Use enum defines
When setting the default EEPROM values use
the values from the enums instead of "magic" values.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:50 -08:00
Ivo van Doorn ebcf26dae9 [PATCH] rt2x00: Move quality statistics into seperate structure
Move all link quality statistics variables into
the link_qual structure. This cleans up the link
structure and allows us to use it for more then
just statistics.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:02:49 -08:00
Eric W. Biederman 6b175b26c1 [NETNS]: Add netns parameter to inet_(dev_)add_type.
The patch extends the inet_addr_type and inet_dev_addr_type with the
network namespace pointer. That allows to access the different tables
relatively to the network namespace.

The modification of the signature function is reported in all the
callers of the inet_addr_type using the pointer to the well known
init_net.

Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:01:27 -08:00
Li Zefan 6e32814bc8 [CONNECTOR]: Cleanup struct cn_callback_entry
- 'cb' is a fake struct member. In a previous patch struct cn_callback
was renamed to cn_callback_id, so 'cb' should have been deleted at that
time.

- 'nls' isn't used and is redundant, we can retrieve this data through
cn_callback_entry.pdev->nls.

- 'seq' and 'group' should be u32, as they are declared to be u32 in
other places.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:40 -08:00
Li Zefan 96a899655e [CONNECTOR]: Cleanup struct cn_queue_dev
Struct member netlink_groups is never used, and I don't see how it can
be useful.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:39 -08:00
Li Zefan 00f5e06c03 [CONNECTOR]: clean up {,__}cn_rx_skb()
- __cn_rx_skb() does nothing but calls cn_call_callback(), it doesn't
check skb and msg sizes as the comment suggests, but cn_rx_skb() checks
those sizes.

- In cn_rx_skb() Local variable 'len' is not used. 'len' is probably
intended to be passed to skb_pull(), but here skb_pull() is not needed,
instead skb_free() is called.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:38 -08:00
Li Zefan fd00eeccd9 [CONNECTOR]: add a missing break in cn_netlink_send()
Each entry in the list has a unique id, so just break out of the
loop if the matched id is found.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:37 -08:00
Adrian Bunk f1862b0ae2 [SHAPER]: The scheduled shaper removal.
This patch contains the scheduled removal of the shaper driver.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:29 -08:00
Jorge Boncompte 7d1f8db40b [ATM]: [he] fixing compilation when you define USE_RBPS_POOL/USE_RBPL_POOL
Signed-off-by: Jorge Boncompte <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:15 -08:00
Joonwoo Park a5929af407 [ATM]: [ambassador] kmalloc + memset conversion to kzalloc
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:14 -08:00
Adrian Bunk 900092a45e [ATM]: [he] This patch removes the ancient version string.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:12 -08:00
David S. Miller 15ca36fb99 [LIBERTAS]: Remove last stray user of MAC_FMT.
Reported by Denis V. Lunev

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:08 -08:00
Michael Chan 7ffc49a6ee [ETH]: Combine format_addr() with print_mac().
print_mac() used many most net drivers and format_addr() used by
net-sysfs.c are very similar and they can be intergrated.

format_addr() is also identically redefined in the qla4xxx iscsi
driver.

Export a new function sysfs_format_mac() to be used by net-sysfs,
qla4xxx and others in the future.  Both print_mac() and
sysfs_format_mac() call _format_mac_addr() to do the formatting.

Changed print_mac() to use unsigned char * to be consistent with
net_device struct's dev_addr.  Added buffer length overrun checking
as suggested by Joe Perches.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:05 -08:00
Matt Carlson 255f97b311 [TG3]: Update version to 3.87
This patch updates the version number to 3.87.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:35 -08:00
Matt Carlson ef167e2703 [TG3]: Fix supporting flowctrl code
This patch does three things.  It modifies tg3_setup_flow_control() to
use the administrator requested flow control settings if
autonegotiation is turned off.  It slightly modifies the
tg3_setup_fiber_mii_phy() function to account for this new use case.
And finally, it does the same for tg3_setup_copper_phy().

The copper modifications are more than a small multi-line change.  The
new code makes an attempt to avoid a link renegotiation if the link is
active at half duplex and the only difference between the current
advertised settings and requested advertised settings is the
flow control advertisements.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:34 -08:00
Matt Carlson 5be73b471b [TG3]: Correct sw autoneg flow control advertisements
This patch modifies the software autoneg code to use the administrator
specified flow control parameters.  Since the autonegotiation code uses
alternative flow control enumerations, the 1000-BaseX utility functions
are used and code was added to convert the definitions to and from the
alternate enumerations.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:34 -08:00
Matt Carlson 82cd3d11f3 [TG3]: Correct 5704S flowctrl advertisements
This patch modifies the 5704S hardware autoneg code to use the
administrator specified flow control parameters.  Since the 5704S uses
device specific flow control enumerations, the 1000-BaseX utility
functions are used and code was added to convert the definitions to and
from the proprietary enumerations.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:33 -08:00
Matt Carlson c98f6e3be1 [TG3]: Replace some magic 5704S constants
This patch replaces magic values with preprocessor definitions for
the sg_dig_ctrl and sg_dig_status registers.  This is preparatory work
for the next patch.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:32 -08:00
Matt Carlson ba4d07a848 [TG3]: Add 1000T & 1000X flowctl adv helpers
This patch adds two functions designed to convert abstract TX & RX
flow control parameters to 1000-BaseT and 1000-BaseX autonegotiation
advertisements.  Code that uses standard definitions which statically
advertises TX & RX flow control has been replaced with code that
configures the advertisements based on administrator dictated
preferences.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:31 -08:00
Matt Carlson 95937268b7 [TG3]: Add 1000T & 1000X flowctrl resolvers
This patch adds two new utility functions to resolve flow control.  One
function resolves flow control based on 1000-BaseT register definitions.
The other resolves flow control based on 1000-Base X register
definitions.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:30 -08:00
Matt Carlson 8d01862108 [TG3]: Separate requested and actual flow control parameters
This patch removes the TX and RX flow control flags from tg3_flags and
adds two new flow control variables, flowctrl and active_flowctrl.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:29 -08:00
Mattias Nissler 1abbe498e4 mac80211: clean up rate selection
Move some code out of rc80211_simple since it's probably needed for all rate
selection algorithms, and fix iwlwifi accordingly. While at it, clean up the
rate_control_get_rate() interface.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:17 -08:00
Joe Perches 2caf62f6ca [NIU]: Use print_mac
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:15 -08:00
Joe Perches d664537228 [TG3]: Use print_mac
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:14 -08:00
Joe Perches 137919a9ba [SUNVNET]: Use print_mac
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:59:13 -08:00
Johannes Berg 03bffc1341 wireless: make drivers include the TSF RX flag where appropriate
These drivers pass full mactime information to the stack, make them
indicate this via the new RX_FLAG_TSFT to get mac80211 to show this
information in monitor mode.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:58:26 -08:00
Dan Williams 374fdfbc67 introduce WEXT scan capabilities
Introduce scan capabilities to WEXT so that userspace can do intelligent
things with scan behavior such as handling hidden SSIDs more gracefully.
If the driver reports a specific scan capability, the driver must
respect the options specified in the iw_scan_req structure when handling
the SIOCSIWSCAN call, unless it's mode or state does not allow it to do
so, in which case it must return an error.

This version switches to Dave Kilroy's suggestion of claiming unused
padding space for the scan_capa field.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:58:25 -08:00
Joe Perches 17159b0b49 [PARISC]: Fix build after ipv4_is_*() changes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:58:20 -08:00
Joe Perches 6360a02af1 [IPV4] drivers/infiniband: Use ipv4_is_<type>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:58:17 -08:00
Matthias Kaehlcke 5e41fb8321 [PPP] synchronous tty: convert dead_sem to completion
PPP synchronous tty channel driver: convert the semaphore dead_sem to a
completion

Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:58:07 -08:00
Michael Chan 2ba582b782 [BNX2]: Fix compiler warning.
Change bnx2_init_napi() to void.

Warning was noted by DaveM.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:57:40 -08:00
Michael Chan f13561cb2f [BNX2]: Update version to 1.7.1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:57:40 -08:00
Michael Chan 57851d8453 [BNX2]: Enable new tx ring.
Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring.  Enable MSIX when the hardware supports it.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 14:57:39 -08:00