Teach sta_info_flush() to optionally also remove stations
from all VLANs associated with an AP interface to optimise
the station removal (in particular, synchronize_net().)
To not have to add the vlans argument throughout, do some
refactoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current channel switch code has a potential deadlock:
1) * cfg80211_stop_ap acquires wdev-lock
* ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work,
which acquires the associated worker-lock
2) * ieee80211_csa_finalize_work holds the worker-lock when run
* it calls cfg80211_ch_switch_notify which will claim the wdev-lock,
and also needs to claim the sdata-lock (which is the same as the
wdev-lock) to modify the beacons.
It is sufficient to just set the channel switch active to false. If the
worker is running later, it will find the channel switch to not be
active anymore and returns immediately without changing anything.
Canceling the worker is done anyway when the interface goes down
(ieee80211_do_stop).
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa finalize worker needs to change the beacon information (for
different modes). These are normally protected under rtnl lock, but the
csa finalize worker is called by drivers and should not acquire the RTNL
lock. Therefore change access protection for beacons to sdata/wdev lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fix sdata_dereference]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason why we should have only one channel switch
announcement at a time for a single phy. When support for channel
switch with multiple contexts and multiple vifs per context is
implemented, we will need the chandef data for each vif. Move the
csa_chandef structure to sdata to prepare for this.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[Fixed compilation with mesh]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use put_unaligned_le16 in mesh_plink_frame_tx.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh STA receiving the mesh CSA action frame is not able to trigger
the mesh channel switch due to the incorrect handling and comparison
of mesh channel switch parameters element (MCSP)'s TTL. Make sure
the MCSP's TTL is updated accordingly before calling the
ieee80211_mesh_process_chnswitch. Also, we update the beacon before
forwarding the CSA action frame, so MCSP's precedence value and
initiator flag need to be updated prior to this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh beacon was not being rebuild after user triggered a mesh
powersave change.
To solve this issue use ieee80211_mbss_info_change_notify instead
of ieee80211_bss_info_change_notify. This helper function forces
mesh beacon to be rebuild and then notifies the driver about the
beacon change.
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ee1f668136.
The aformentioned commit added a check to allow
'iw wlan0 set power_save off' to work for mesh interfaces.
However, this is problematic because it also allows
'iw wlan0 set power_save on', which will crash in short order
because all of the subsequent code manipulates sdata->u.mgd.
The power-saving states for mesh interfaces can be manipulated
through the mesh config, e.g:
'iw wlan0 set mesh_param mesh_power_save=active' (which,
despite the name, actualy disables power saving since the
setting refers to the type of sleep the interface undergoes).
Cc: stable@vger.kernel.org
Fixes: ee1f668136 ("mac80211: allow disable power save in mesh")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CSA completion could call in a driver
bss_info_changed() with a garbled `changed` flag
leading to all sorts of problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the required procedures for mesh channel switching as defined
in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA
and MCSP elements as followed:
* Add the function for updating the beacon and probe response frames
with CSA and MCSP elements during the period of switching to the new
channel. Both CSA and MCSP elements must be included in beacon and
probe response frames until the intended channel switch time.
* The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements
will then be removed from the beacon or probe response frames once the
new channel is switched to.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes errors in the mesh powersave logic which
cause that remote peers do not get peer power mode change
notifications and mesh peer service periods (MPSPs) got
stuck.
When closing a peer link, set the (now invalid) peer-specific
power mode to 'unknown'.
Avoid overhead when local power mode is unchanged.
Reliably clear MPSP flags on peering status update.
Avoid MPSP flags getting stuck by not requesting a further
MPSP ownership if we already are an MPSP owner.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Limit the current implementation to a single channel context used by
a single vif, thereby avoiding multi-vif/channel complexities.
Reuse the main function from AP CSA code, but move a portion out in
order to fit the STA scenario.
Add a new mac80211 HW flag so we don't break devices that don't support
channel switch with channel-contexts. The new behavior will be opt-in.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function adds the channel switch announcement implementation for the
IBSS code. It is triggered by userspace (mac80211/cfg) or by external
channel switch announcement, which have to be adopted. Both CSAs in
beacons and action frames are supported. As for AP mode, the channel
switch is applied after some time. However in IBSS mode, the channel
switch IEs are generated in the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Useful for userspace mesh to authenticate and peer without
a station entry, since both steps may fail anyway.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 6d810f1032
In this way an IBSS station will not use the AUTH messages
to trigger a state reinitialisation anymore.
The behaviour was racy and was not working properly.
It has been introduced to help wpa_supplicant to support
IBSS/RSN, however all the logic is now getting moved into
wpa_s itself which will also be in charge of handling the
AUTH messages thanks to the mgmt frame registration.
If userspace does not register for receiving AUTH frames
then mac80211 will still reply by itself.
At the same time, the auth frame registration counter can be
removed since it is not needed anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[remove unused variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case. Fail if offchan is required.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[fix RCU locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My cfg80211/mac80211 locking unification broke the sdata
locking in ieee80211_set_power_mgmt, it needs to acquire
the lock for __ieee80211_request_smps(). Add the locking.
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the mesh_auth_id was disabled. Instead set the
correct mesh authentication bit based on the mesh setup.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no real difference between *array and array, but
the former confuses smatch so write it differently. The
generated code is exactly the same.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg