clk providers shouldn't need to use the consumer APIs (clk.h).
Add provider APIs to replace the __clk_*() APIs that take a
struct clk_hw as their first argument instead of a struct clk.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
Introduce generic kasan_populate_zero_shadow(shadow_start,
shadow_end). This function maps kasan_zero_page to the
[shadow_start, shadow_end] addresses.
This replaces x86_64 specific populate_zero_shadow() and will
be used for ARM64 in follow on patches.
The main changes from original version are:
* Use p?d_populate*() instead of set_p?d()
* Use memblock allocator directly instead of vmemmap_alloc_block()
* __pa() instead of __pa_nodebug(). __pa() causes troubles
iff we use it before kasan_early_init(). kasan_populate_zero_shadow()
will be used later, so we ok with __pa() here.
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexey Klimov <klimov.linux@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Keitel <dkeitel@codeaurora.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yury <yury.norov@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1439444244-26057-3-git-send-email-ryabinin.a.a@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TqKo
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a regression fix at the videobuf2 core driver
- fix error handling at mantis probing code
- revert the IR encode patches, as the API is not mature enough.
So, better to postpone the changes to a latter Kernel
- fix Kconfig breakages on some randconfig scenarios.
* tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] mantis: Fix error handling in mantis_dma_init()
Revert "[media] rc: rc-ir-raw: Add scancode encoder callback"
Revert "[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper"
Revert "[media] rc: ir-rc5-decoder: Add encode capability"
Revert "[media] rc: ir-rc6-decoder: Add encode capability"
Revert "[media] rc: rc-core: Add support for encode_wakeup drivers"
Revert "[media] rc: rc-loopback: Add loopback of filter scancodes"
Revert "[media] rc: nuvoton-cir: Add support for writing wakeup samples via sysfs filter callback"
[media] vb2: Fix compilation breakage when !CONFIG_BUG
[media] vb2: Only requeue buffers immediately once streaming is started
[media] media/pci/cobalt: fix Kconfig and build when SND is not enabled
[media] media/dvb: fix ts2020.c Kconfig and build
Pull drm fixes from Dave Airlie:
"A bunch of i915 fixes, one revert a VBT fix that was a bit premature,
and some braswell feature removal that the hw actually didn't support.
One radeon race fix at boot, and one hlcdc build fix, one fix from
Russell that fixes build as well with new audio features.
This is hopefully all I have until -next"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix hotplug race at startup
drm/edid: add function to help find SADs
drm/i915: Avoid TP3 on CHV
drm/i915: remove HBR2 from chv supported list
Revert "drm/i915: Add eDP intermediate frequencies for CHV"
Revert "drm/i915: Allow parsing of variable size child device entries from VBT"
drm/atmel-hlcdc: Compile suspend/resume for PM_SLEEP only
drm/i915: Flag the execlists context object as dirty after every use
Enables CPU frequency scaling on Jetson TK1 and enables the GK20A GPU on
Venice2 and Jetson TK1. This also enables support for the PMU hardware
found on Tegra124, which among other things, can be used for performance
measurements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tdwi
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Devicetree changes for v4.3-rc1
Enables CPU frequency scaling on Jetson TK1 and enables the GK20A GPU on
Venice2 and Jetson TK1. This also enables support for the PMU hardware
found on Tegra124, which among other things, can be used for performance
measurements.
* tag 'tegra-for-4.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
pinctrl: tegra: Only set the gpio range if needed
clk: tegra: Add the DFLL as a possible parent of the cclk_g clock
clk: tegra: Save/restore CCLKG_BURST_POLICY on suspend
clk: tegra: Add Tegra124 DFLL clocksource platform driver
clk: tegra: Add DFLL DVCO reset control for Tegra124
clk: tegra: Introduce ability for SoC-specific reset control callbacks
clk: tegra: Add functions for parsing CVB tables
clk: tegra: Add closed loop support for the DFLL
clk: tegra: Add library for the DFLL clock source (open-loop mode)
clk: tegra: Add binding for the Tegra124 DFLL clocksource
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the helper AHASH_REQUEST_ON_STACK for those users
of ahash that are synchronous only.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch introduces the crypto skcipher interface which aims
to replace both blkcipher and ablkcipher.
It's very similar to the existing ablkcipher interface. The
main difference is the removal of the givcrypt interface. In
order to make the transition easier for blkcipher users, there
is a helper SKCIPHER_REQUEST_ON_STACK which can be used to place
a request on the stack for synchronous transforms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adds support for Tegra210, which allows the SMMU to be used on this new
SoC generation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=H73u
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
ARM: tegra: Memory controller updates for v4.3-rc1
Adds support for Tegra210, which allows the SMMU to be used on this new
SoC generation.
* tag 'tegra-for-4.3-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra: Add Tegra210 support
memory: tegra: Add support for a variable-size client ID bitfield
memory: tegra: Expose supported rates via debugfs
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a bit more of Tegra210 support, which is shaping up pretty
nicely. Other than that there are a couple of cleanup patches here, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xo46
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
ARM: tegra: Core SoC changes for v4.3-rc1
This contains a bit more of Tegra210 support, which is shaping up pretty
nicely. Other than that there are a couple of cleanup patches here, too.
* tag 'tegra-for-4.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cpuidle: implement cpuidle_state.enter_freeze()
ARM: tegra: Disable cpuidle if PSCI is available
soc/tegra: pmc: Use existing pclk reference
soc/tegra: pmc: Remove unnecessary return statement
soc: tegra: Remove redundant $(CONFIG_ARCH_TEGRA) in Makefile
soc/tegra: fuse: Add spare bit offset for Tegra210
soc/tegra: fuse: Add spare bit offset for Tegra124
soc/tegra: fuse: Add spare bit offset for Tegra114
soc/tegra: fuse: Rename core_* to soc_*
soc/tegra: fuse: Add Tegra210 support
soc/tegra: fuse: Unify Tegra20 and Tegra30 drivers
soc/tegra: fuse: Restrict legacy code to 32-bit ARM
soc/tegra: pmc: Add Tegra210 support
soc/tegra: pmc: Restrict legacy code to 32-bit ARM
soc/tegra: pmc: Avoid usage of uninitialized variable
soc/tegra: Add Tegra210 support
soc/tegra: Add Tegra132 support
Signed-off-by: Olof Johansson <olof@lixom.net>
- moved the DT reset binding includes from
include/dt-bindings/reset-controller to include/dt-bindings/reset
- new driver for LPC18xx Reset Generation Unit (RGU)
- of_device_id array in the STi driver changed to const.
- extend SoCFPGA reset driver to support Arria10
- new ath79 reset controller driver for AR71XX/AR9XXX
- new driver for Xilinx Zynq reset controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GBec
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.3' of git://git.pengutronix.de/git/pza/linux into next/drivers
Reset controller changes for v4.3
- moved the DT reset binding includes from
include/dt-bindings/reset-controller to include/dt-bindings/reset
- new driver for LPC18xx Reset Generation Unit (RGU)
- of_device_id array in the STi driver changed to const.
- extend SoCFPGA reset driver to support Arria10
- new ath79 reset controller driver for AR71XX/AR9XXX
- new driver for Xilinx Zynq reset controller
* tag 'reset-for-4.3' of git://git.pengutronix.de/git/pza/linux:
reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
MIPS: ath79: Add the reset controller to the AR9132 dtsi
reset: Add a driver for the reset controller on the AR71XX/AR9XXX
devicetree: Add bindings for the ATH79 reset controller
reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
doc: dt: add documentation for lpc1850-rgu reset driver
reset: add driver for lpc18xx rgu
reset: sti: constify of_device_id array
ARM: STi: DT: Move reset controller constants into common location
MAINTAINERS: add include/dt-bindings/reset path to reset controller entry
Signed-off-by: Olof Johansson <olof@lixom.net>
Here are a small collecton of sound fix patches. The most significant
one is the disablement of newly introduced topology API. Its ABI
couldn't be stabilized enough, so we decided to delay for 4.3 in the
end. Other than that, all oneliner fixes: a USB-audio runtime PM fix
and a couple of HD-audio quirks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=c+1+
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a small collecton of sound fix patches.
The most significant one is the disablement of newly introduced
topology API. Its ABI couldn't be stabilized enough, so we decided to
delay for 4.3 in the end. Other than that, all oneliner fixes: a
USB-audio runtime PM fix and a couple of HD-audio quirks"
* tag 'sound-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add dock support for Thinkpad W541 (17aa:2211)
ALSA: usb-audio: Fix runtime PM unbalance
ASoC: topology: Disable use from userspace
ASoC: topology: Add Kconfig option for topology
ALSA: hda - Fix the white noise on Dell laptop
TX_ENDIAN/RX_ENDIAN bits define whether to reverse the endian
order of the data DMA from/to memory. The endian order should
keep the same with cpu endian.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a pci_scan_root_bus_msi() interface so an arch can specify the MSI
controller up front. This removes the need for a pcibios callback to set
the MSI controller later.
This is not exported because I'd like to replace the variety of "scan root
bus" interfaces with a single, more extensible interface that can handle
the MSI controller, domain, pci_ops, resources, etc. I hope this interface
is temporary.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Add a function to find the start of the SADs in the ELD. This
complements the helper to retrieve the SAD count.
[airlied: this fixes a build problem with the alsa eld helper
which required this].
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This helper is required for irq chips which do not implement a
irq_set_type callback and need to call down the irq domain hierarchy
for the actual trigger type change.
This helper is required to fix further wreckage caused by the
conversion of TI OMAP to hierarchical irq domains and therefor tagged
for stable.
[ tglx: Massaged changelog ]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-3-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV1K6xAAoJECTWi3JdVIfQl60H/Aiq3smUvb+npgLI402pdzZ8
eaGVSw1oGO7NFylBDu8FeiJLBvl4ZQmSfMbaLBJ50JPKqY1nFjOXFk0nWatQ8TPY
0aB1NKCIGNNCWXTO3ABZ8zeT5AH218n3t8tTUxWzOS1RhpZMwePVuS83+cdwfxAZ
He29rX2xfKFaGo92NMB707vU6aobYC0jc4pIaVoYLN7E49leTSzgGKKNVW2JyEog
d44Zd7jEXPY1lj166sEEF4axAzGc2ZkwsbmOmymbszEBkYtDVs1Q1omFf+CNi31Y
16bLwOVzTXVM7PeheRF2Tp6qtcyDpQhLicfBjakkJ1X5MtW3OzoutGli/isIh2g=
=Gj9l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-disable-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Disable topology support for v4.2
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit da7ee60b03.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyhktAAoJEFBXWFqHsHzOjQwH/0CXyzRUCJjHqxAHsnvHzOZG
AvjYWqaimxP5PD6TRG1bRxfWWXNL7zZGqj9Jd/l5HIWdWfUxnOLeMy40yfcs+AsH
9CHUunu0rahIDY6YF4gA7F5jyfnSIzxwE8Bkva7nmXvf0XmazTwhCXxYPzdBjMSG
Cf39datyTj9ZS3DD/DAKzRN//zebQCJmPuAdmIlRZljBkoLVPeEZrVxkSN0trRin
vKPQIpamM2DXIMmdiPK52J0j8Vwq4qbiGvvAwUKsaRCUVYfpunpVcZSYgMqm8iEa
7PKuurbVeuvZLzS0Bdq05tCkwVXt0upk0ayf0i8DkHFExX79TNTbONOLJwmigjo=
=iAvA
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree updates for 4.3:
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
* tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: dts: imx6ul: add snvs power key support
ARM: dts: imx6ul: add RTC support
ARM: dts: imx6ul: enable GPC as extended interrupt controller
ARM: dts: imx6sx: correct property name for wakeup source
ARM: dts: add property for maximum ADC clock frequencies
ARM: dts: imx7d: enable snvs rtc, onoffkey and power off
ARM: dts: imx6ul-14x14-evk: add fec1 and fec2 support
ARM: dts: imx: add fec1 and fec2 nodes for SOC i.MX6UL
ARM: dts: imx27: add support of internal rtc
ARM: dts: vf-colibri: define stdout-path property
ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR
ARM: dts: ls1021a: Add the eTSEC controller nodes
ARM: dts: imx6ul: add qspi support
ARM: dts: imx6ul: fix low case define in imx6ul-pinfunc.h
ARM: dts: imx6ul: add usb host and function support
ARM: dts: vfxxx: Add io-channel-cells property for ADC node
ARM: dts: ls1021a: Add dts nodes for audio on LS1021A
ARM: imx6qdl-sabreauto.dtsi: enable USB support
ARM: dts: imx: update snvs to use syscon access register
ARM: dts: imx: add imx6ul and imx6ul evk board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add i.MX6 Ultralite SoC support, which is the newest addition to
i.MX6 family. It integrates a single Cortex-A7 core and a power
management module that reduces the complexity of external power
supply and simplifies power sequencing.
- Change SNVS RTC driver to use syscon interface for register access,
and add SNVS power key driver support.
- Add a second clock for mxc rtc driver, and support device tree probe
for the driver.
- Add FEC MAC reference clock and phy fixup initialization for i.MX6UL
platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyg8nAAoJEFBXWFqHsHzOQC8H/iY+cdNfAWIxYmt2CeF607su
fLaycUSUPqPAERUTcHpjKyiKkRg2NWV7vFVWCkKaQ3RZ+IW6xNntkqMxzocS1sh2
+70Ckp+B0orGuo96PkEXua9fNPf8/yaGiDhuJpK966VRRSSXRD15uOuqHAJ2Jz/v
HEnEm3KANSSYS1heEJRqiiCsqhADRWl2RzgfV327aXtScP9zXlbJGlEc/jUVAY65
wbqjsXdySeS3rECNMAYXnPU7IlK4NkRqrOi1JmTJCBlXqV2b6dBfjgIu9jOa91UG
yRj7IEBJemqT4Ap1ee2NR3H1lDngt2JKg9XqRDL3j9alYvhAWGvhSY2UH2iPrFg=
=emep
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC changes for 4.3:
- Add i.MX6 Ultralite SoC support, which is the newest addition to
i.MX6 family. It integrates a single Cortex-A7 core and a power
management module that reduces the complexity of external power
supply and simplifies power sequencing.
- Change SNVS RTC driver to use syscon interface for register access,
and add SNVS power key driver support.
- Add a second clock for mxc rtc driver, and support device tree probe
for the driver.
- Add FEC MAC reference clock and phy fixup initialization for i.MX6UL
platform.
* tag 'imx-soc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
rtc: snvs: select option REGMAP_MMIO
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
input: snvs_pwrkey: use "wakeup-source" as deivce tree property name
Document: devicetree: input: imx: i.mx snvs power device tree bindings
input: keyboard: imx: add snvs power key driver
Document: dt: fsl: snvs: change support syscon
rtc: snvs: use syscon to access register
ARM: imx: add low-level debug support for i.mx6ul
ARM: imx: add i.mx6ul msl support
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 484ebaedec as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1d958bef45 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3cf1fc8065 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the topology API is still in sufficient flux for changes to be
identified disable the use of the userspace ABI by adding #error
statements to the code, ensuring that nobody relies on the headers as
currently defined. It is expected that this change will be reverted for
v4.3.
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull drm fixes from Dave Airlie:
"These came in late last week, I wanted to look over the mst one before
forwarding, but it seems good.
Just three i915 and one MST fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Commit planes on each crtc separately.
drm/i915: calculate primary visibility changes instead of calling from set_config
drm/i915: Only dither on 6bpc panels
drm/dp/mst: Remove port after removing connector.
Allow the topology code to be compiled out so that users who don't need
topology don't need to havve the code compiled in, saving them some
memory.
Some more configuration could be added to remove some of the hooks into
the core data structures but that is probably best done with some
refactoring to use functions to do the updates of the data structures
rather than ifdefing in the code as we'd need to do at the minute.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull libata fixes from Tejun Heo:
"Three minor device-specific fixes and revert of NCQ autosense added
during this -rc1.
It turned out that NCQ autosense as currently implemented interferes
with the usual error handling behavior. It will be revisited in the
near future"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_brcmstb: Fix misuse of IS_ENABLED
sata_sx4: Check return code from pdc20621_i2c_read()
Revert "libata: Implement NCQ autosense"
Revert "libata: Implement support for sense data reporting"
Revert "libata-eh: Set 'information' field for autosense"
ata: ahci_brcmstb: Fix warnings with CONFIG_PM_SLEEP=n
Voltage tolerance isn't necessarily same on both sides of the target
voltage and regulator_set_voltage_tol() wouldn't be suitable in such
cases.
Add another routine regulator_set_voltage_triplet(), which accepts
target, min and max voltages as arguments.
This first tries to set the voltage between the target voltage and the
upper limit, then fall back on the full range. The idea behind this is
to set regulator's voltage as close to the target voltage, as possible.
Based on regulator_set_voltage_tol().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion between struct timespec and jiffies is not year 2038
safe on 32bit systems. Introduce timespec64_to_jiffies() and
jiffies_to_timespec64() functions which use struct timespec64 to
make it ready for 2038 issue.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The current_kernel_time() is not year 2038 safe on 32bit systems
since it returns a timespec value. Introduce current_kernel_time64()
which returns a timespec64 value.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The struct itimerspec is not year 2038 safe on 32bit systems due to
the limitation of the struct timespec members. Introduce itimerspec64
which uses struct timespec64 instead and provide conversion functions.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patchset include the function update of extcon drivers without critical
update and fix minor issue of extcon drivers.
Detailed description for patchset:
1. Update the extcon drivers:
- Update the logic of microphone detection for extcon-arizona driver
- Support GPIO based USB ID detection of extcon-palmas driver
2. Fix minor issues:
- Clean code and remove the opitonal print_state() function pointer from extcon
core driver
- Clear interrupt bit state before requesting irq on extcon-max778433 driver
- Fix signedness bugs of extcon core driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cd4Z
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-testing
Chanwoo writes:
Update extcon for v4.3
This patchset include the function update of extcon drivers without critical
update and fix minor issue of extcon drivers.
Detailed description for patchset:
1. Update the extcon drivers:
- Update the logic of microphone detection for extcon-arizona driver
- Support GPIO based USB ID detection of extcon-palmas driver
2. Fix minor issues:
- Clean code and remove the opitonal print_state() function pointer from extcon
core driver
- Clear interrupt bit state before requesting irq on extcon-max778433 driver
- Fix signedness bugs of extcon core driver
Now that the AEAD conversion is complete we can rip out the old
AEAD interafce and associated code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the helpers aead_init_geniv and aead_exit_geniv
which are type-safe and intended the replace the existing geniv
init/exit helpers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
single MST fixes from Maarten.
* tag 'topic/drm-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/dp/mst: Remove port after removing connector.
Move struct at91_usbh_data back in ohci-at91.c as this is the only user
left after switching all at91 platforms to DT only.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute authorized shows the authorization state for an interface.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incoming packets in high speed are randomly corrupted by h/w
resulting in multiple errors. This workaround makes FS as
default mode in all affected socs by disabling HS chirp
signalling.This errata does not affect FS and LS mode.
Forces all HS devices to connect in FS mode for all socs
affected by this erratum:
P3041 and P2041 rev 1.0 and 1.1
P5020 and P5010 rev 1.0 and 2.0
P5040, P1010 and T4240 rev 1.0
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVzU3lAAoJEEhZKYFQ1nG7nZ4H/AsCAhoiUqcyP4fRziaZzexa
F55CuhIVd6vg6vhuiccoUo4XZXR6IsZikczNowWphqXhtQUBr/rvv0VSb2sMxZfn
AgdNuinhGUat4rdcf0earr9+EQzjbdrHoxDzFKes21S0vS+J3TaYUk6F7Q6sUL81
t97itMmKBrffMZLsQzB9MJo4E8mD4JNlWu/ezGNu11ZD2/w8Ha7GpyExyb2AGHrs
M1rlE6Ph8AKpyECI7OecCxPIDyDRuUQ8Bvj+MkR9BrDX1gOv512ZLfRbIGJCqVOO
A2Urzh/jEI9e7ttGqSpMxGYKZ4wvZ7Ta5IvLLseb0vszM2oQGDNHcJx7fKOuUVU=
=IIud
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB: chipidea updates for v4.3-rc1
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WuIB
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
The system bus and chipidea IP have different limitations for
both host and device mode.
For example, with below errata, we need to enable SDIS(Stream Disable
Mode) at host mode. But we don't want it for device mode at the
same system.
TAR 9000378958
Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to
Hang on OUT Retry
Impacted Configuration: Host mode, all transfer types
Description:
The host core operating in streaming mode may under run while sending
the data packet of an OUT transaction. This under run can occur if
there are unexpected system delays in fetching the remaining packet
data from memory. The host forces a bad CRC on the packet, the device
detects the error and discards the packet. The host then retries a Bulk,
Interrupt, or Control transfer if an under run occurs according to the
USB specification. During simulations, it was found that the host does
not issue the retry of the failed bulk OUT. It does not issue any other
transactions except SOF packets that have incorrect frame numbers.
The second failure mode occurs if the under run occurs on an ISO OUT
transaction and the next ISO transaction is a zero byte packet. The host
does not issue any transactions (including SOFs). The device detects a
Suspend condition, reverts to full speed, and waits for resume signaling.
A third failure mode occurs when the host under runs on an ISO OUT and
the next ISO in the schedule is an ISO OUT with two max packets of 1024
bytes each. The host should issue MDATA for the first OUT followed by
DATA1 for the second. However, it drops the MDATA transaction, and
issues the DATA1 transaction.
The system impact of this bug is the same regardless of the failure mode
observed. The host core hangs, the ehci_ctrl state machine waits for the
protocol engine to send the completion status for the corrupted
transaction, which never occurs. No indication is sent to the host
controller driver, no register bits change and no interrupts occur.
Eventually the requesting application times out.
Detailed internal behavior:
The EHCI control state machine (ehci_ctrl) in the DMA block is responsible
for parsing the schedules and initiating all transactions. The ehci_ctrl
state machine passes the transaction details to the protocol block by
writing the transaction information in to the TxFIFO. It then asserts
the pe_hst_run_pkt signal to inform the host protocol state machine
(pe_hst_state) that there is a packet in the TxFIFO.
A tag of 0x0 indicates a start of packet with the data providing the
following information:
35:32 Tag
31:30 Reserved
29:23 Endpoint (lowest 4 bits)
22:16 Address
15:10 Reserved
9:8 Endpoint speed
7:6 Endpoint type
5:6 Data Toggle
3:0 PID
The pe_hst_state reads the packet information and constructs the packet
and issues it to the PHY interface.
The ehci_ctrl state machine writes the start transaction information in
to the TxFIFO as 0x03002910c for the OUT packet that had the under run
error. However, it writes 0xC3002910C for the retry of the Out
transaction, which is incorrect.
The pe_hst_state enters a bus timeout state after sending the bad CRC
for the packet that under ran. It then purges any data that was back
filled in to the TxFIFO for the packet that under ran. The pe_hst_state
machine stops purging the TxFIFO when it is empty or if it reads a
location that has a tag of 0x0, indicating a start of packet command.
The pe_hst_state reads 0xC3002910C and discards it as it does not decode
to a start of packet command. It continues to purge the OUT data that
has been pre-buffered for the OUT retry . The pe_hst_state detects the
hst_packet_run signal and attempts to read the PID and address
information from the TxFIFO. This location has packet data and so does
not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD
state where the frame_num_counter is updated. The frame_num_counter
is updated with the data in the TxFIFO. In this case, the data is
incorrect as the ehci_ctrl state machine did not initiate the load.
The hst_pe_state machine detects the SOF request signal and sends an
SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine
waits indefinitely in the run_pkt state waiting for the completion
status from pe_hst_state machine, which will never happen.
The ISO failure case is similar except that there is no retry for ISO.
The ehci_ctrl state machine moves to the next transfer in the periodic
schedule. If the under run occurs on the last entry of the periodic
list then it moves to the Async schedule.
In the case of ISO OUT simulations, the next ISO is a zero byte OUT
and again the start of packet command gets corrupted. The TxFIFO is
empty when the hst_pe_state attempts to read the Address and PID
information as the transaction is a zero byte packet. This results
in the hst_pe_state machine staying in the GET_PID state, which means
that it does not issue any transactions (including SOFs). The device
detects a Suspend condition and reverts to full speed mode and waits
for a Resume or Reset signal.
The EHCI specification allows a Non-DoubleWord (32 bits) offset to
be used as a current offset for Buffer Pointer Page 0 of the qTD.
In Non-DoubleWord aligned cases, the core reads the packet data
from the AHB memory, performs the alignment operation before writing
it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP)
is written to the TxFIFO after all the packet data has been written
in to the TxFIFO. The alignment function is reset to Idle by the EOP
tag. The corruption of the start of packet command arises because the
packet buffer for the OUT transaction that under ran is not aligned
to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The
alignment function is still active when the start packet information
is written in to the TxFIFO for the retry of the bulk packet or for
the next transaction in the case of an under run on an ISO. This
results in the corruption of the start tag and the transaction
information.
Click for waveform showing the command 0x 0000300291 being written in
to the TX FIFO for the Out that under ran.
Click for waveform showing the command 0xC3002910C written to the
TxFIFO instead of 0x 0000300291
Versions affected: Versions 2.10a and previous versions
How discovered: Customer simulation
Workaround:
1- The EHCI specification allows a non-DoubleWord offset to be used
as a current offset for Buffer Pointer Page 0 of the qTD. However,
if a DoubleWord offset is used then this issue does not arise.
2- Use non streaming mode to eliminate under runs.
Resolution:
The fix involves changes to the traffic state machine in the
vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context
information by encoding the transaction results on the
hst_op_context_update signals at the end of a transaction. The signal
hst_op_context_update is added to the traffic state machine, and the
tx_fifo_under_ran_r signal is generated if the transaction results in
an under run error. Click for waveform
The traffic state machine then traverses to the do_eop states if the
tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to
the TxFIFO as shown in this waveform .
The EOP tag resets the align state machine to the Idle state ensuring
that the next command written by the echi_ctrl state machine does not
get corrupted.
File(s) modified:
RTL code fixed: …..
Method of reproducing: This failure cannot be reproduced in the current
test bench.
Date Found: March 2010
Date Fixed: June 2010
Update information:
Added the RTL code fix
Signed-off-by: Peter Chen <peter.chen@freescale.com>
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Remove pci_ats_enabled(). There are no callers outside the ATS code
itself. We don't need to check ats_cap, because if we don't find an ATS
capability, we'll never set ats_enabled.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Stop caching the Invalidate Queue Depth in struct pci_dev.
pci_ats_queue_depth() is typically called only once per device, and it
returns a fixed value per-device, so callers who need the value frequently
can cache it themselves.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Move ATS declarations to linux/pci.h so they're all in one place.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The extended capabilities list is linked with 12-bit pointers, and the ATS
Smallest Translation Unit and Invalidate Queue Depth fields are both 5
bits.
Use u16 and u8 to hold the extended capability address and the stu and qdep
values. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The pci_ats struct is small and will get smaller, so I don't think it's
worth allocating it separately from the pci_dev struct.
Embed the ATS fields directly into struct pci_dev.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Previously, we allocated pci_ats structures when an IOMMU driver called
pci_enable_ats(). An SR-IOV VF shares the STU setting with its PF, so when
enabling ATS on the VF, we allocated a pci_ats struct for the PF if it
didn't already have one. We held the sriov->lock to serialize threads
concurrently enabling ATS on several VFS so only one would allocate the PF
pci_ats.
Gregor reported a deadlock here:
pci_enable_sriov
sriov_enable
virtfn_add
mutex_lock(dev->sriov->lock) # acquire sriov->lock
pci_device_add
device_add
BUS_NOTIFY_ADD_DEVICE notifier chain
iommu_bus_notifier
amd_iommu_add_device # iommu_ops.add_device
init_iommu_group
iommu_group_get_for_dev
iommu_group_add_device
__iommu_attach_device
amd_iommu_attach_device # iommu_ops.attach_device
attach_device
pci_enable_ats
mutex_lock(dev->sriov->lock) # deadlock
There's no reason to delay allocating the pci_ats struct, and if we
allocate it for each device at enumeration-time, there's no need for
locking in pci_enable_ats().
Allocate pci_ats struct during enumeration, when we initialize other
capabilities.
Note that this implementation requires ATS to be enabled on the PF first,
before on any of the VFs because the PF controls the STU for all the VFs.
Link: http://permalink.gmane.org/gmane.linux.kernel.iommu/9433
Reported-by: Gregor Dick <gdick@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Pull networking fixes from David Miller:
1) Workaround hw bug when acquiring PCI bos ownership of iwlwifi
devices, from Emmanuel Grumbach.
2) Falling back to vmalloc in conntrack should not emit a warning, from
Pablo Neira Ayuso.
3) Fix NULL deref when rtlwifi driver is used as an AP, from Luis
Felipe Dominguez Vega.
4) Rocker doesn't free netdev on device removal, from Ido Schimmel.
5) UDP multicast early sock demux has route handling races, from Eric
Dumazet.
6) Fix L4 checksum handling in openvswitch, from Glenn Griffin.
7) Fix use-after-free in skb_set_peeked, from Herbert Xu.
8) Don't advertize NETIF_F_FRAGLIST in virtio_net driver, this can lead
to fraglists longer than the driver can support. From Jason Wang.
9) Fix mlx5 on non-4k-pagesize systems, from Carol L Soto.
10) Fix interrupt storm in bna driver, from Ivan Vecera.
11) Don't propagate -EBUSY from netlink_insert(), from Daniel Borkmann.
12) Fix inet request sock leak, from Eric Dumazet.
13) Fix TX interrupt masking and marking in TX descriptors of fs_enet
driver, from LEROY Christophe.
14) Get rid of rule optimizer in gianfar driver, it's buggy and unlikely
to get fixed any time soon. From Jakub Kicinski
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
cosa: missing error code on failure in probe()
gianfar: remove faulty filer optimizer
gianfar: correct list membership accounting
gianfar: correct filer table writing
bonding: Gratuitous ARP gets dropped when first slave added
net: dsa: Do not override PHY interface if already configured
net: fs_enet: mask interrupts for TX partial frames.
net: fs_enet: explicitly remove I flag on TX partial frames
inet: fix possible request socket leak
inet: fix races with reqsk timers
mkiss: Fix error handling in mkiss_open()
bnx2x: Free NVRAM lock at end of each page
bnx2x: Prevent null pointer dereference on SKB release
cxgb4: missing curly braces in t4_setup_debugfs()
net-timestamp: Update skb_complete_tx_timestamp comment
ipv6: don't reject link-local nexthop on other interface
netlink: make sure -EBUSY won't escape from netlink_insert
bna: fix interrupts storm caused by erroneous packets
net: mvpp2: replace TX coalescing interrupts with hrtimer
net: mvpp2: enable proper per-CPU TX buffers unmapping
...
Recent versions of the Tegra MC hardware extend the size of the client
ID bitfield in the MC_ERR_STATUS register by one bit. While one could
simply extend the bitfield for older hardware, that would allow data
from reserved bits into the driver code, which is generally a bad idea
on principle. So this patch instead passes in the client ID mask from
from the per-SoC MC data.
There's no MC support for T210 (yet), but when that support winds up
in the kernel, the appropriate soc->client_id_mask value for that chip
will be 0xff.
Based on an original patch by David Ung <davidu@nvidia.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: David Ung <davidu@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the EP93xx boards exclusively use modedb to look up video
modes from the command line. Root out the parametrization of
custom video modes from the platform data and board files
and simplify the driver.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dKt6
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.3, take 2
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
* tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Add resets for EMACs on Arria10
ARM: socfpga: dts: add "altr,modrst-offset" property
dt-bindings: Add reset manager offsets for Arria10
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC part of the Dove PMU series
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXE0fgACgkQCwYYjhRyO9XUKwCeIOTx172942DUMzGwO3feDGZn
zCgAn2yxrZaFqUo/EfVqgieeTGBmY6gh
=gfKo
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.3-2' of git://git.infradead.org/linux-mvebu into next/drivers
mvebu soc changes for v4.3 (part #2)
SoC part of the Dove PMU series
* tag 'mvebu-soc-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets
Signed-off-by: Olof Johansson <olof@lixom.net>
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/b3G
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.3b-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for the 4.3 cycle.
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
Pull RCU changes from Paul E. McKenney:
- The combination of tree geometry-initialization simplifications
and OS-jitter-reduction changes to expedited grace periods.
These two are stacked due to the large number of conflicts
that would otherwise result.
[ With one addition, a temporary commit to silence a lockdep false
positive. Additional changes to the expedited grace-period
primitives (queued for 4.4) remove the cause of this false
positive, and therefore include a revert of this temporary commit. ]
- Documentation updates.
- Torture-test updates.
- Miscellaneous fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Because sched_setscheduler() checks p->flags & PF_NO_SETAFFINITY
without locks, a caller might observe an old value and race with the
set_cpus_allowed_ptr() call from __kthread_bind() and effectively undo
it:
__kthread_bind()
do_set_cpus_allowed()
<SYSCALL>
sched_setaffinity()
if (p->flags & PF_NO_SETAFFINITIY)
set_cpus_allowed_ptr()
p->flags |= PF_NO_SETAFFINITY
Fix the bug by putting everything under the regular scheduler locks.
This also closes a hole in the serialization of task_struct::{nr_,}cpus_allowed.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dedekind1@gmail.com
Cc: juri.lelli@arm.com
Cc: mgorman@suse.de
Cc: riel@redhat.com
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/20150515154833.545640346@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The i.MX clock updates for 4.3:
- Provide a better IPU clock initial settings on imx6dl for getting
HDMI and LVDS at the same time.
- Add clock driver support for i.MX6UL SoC
- Add a second clock for RTC device on i.MX31 and i.MX35
Add Clock Domain support to the Clock Pulse Generator (CPG) Module Stop
(MSTP) Clocks driver using the generic PM Domain. This allows to
power-manage the module clocks of SoC devices that are part of the
CPG/MSTP Clock Domain using Runtime PM, or for system suspend/resume.
SoC devices that are part of the CPG/MSTP Clock Domain and can be
power-managed through an MSTP clock should be tagged in DT with a
proper "power-domains" property.
The CPG/MSTP Clock Domain code will scan such devices for clocks that
are suitable for power-managing the device, by looking for a clock that
is compatible with "renesas,cpg-mstp-clocks".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The port is removed synchronously, but the connector delayed.
This causes a use after free which can cause a kernel BUG with
slug_debug=FPZU. This is fixed by freeing the port after the
connector.
This fixes a regression introduced with
6b8eeca65b
"drm/dp/mst: close deadlock in connector destruction."
Cc: stable@vger.kernel.org
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
After "62bccb8 net-timestamp: Make the clone operation stand-alone from phy
timestamping" the hwtstamps parameter of skb_complete_tx_timestamp() may no
longer be NULL.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CAAM clock support to the i.MX6 clocking infrastructure.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some palmas based chip variants do not have OTG based ID logic.
For these variants we rely on GPIO based USB ID detection.
These chips do have VBUS comparator for VBUS detection so we
continue to use the old way of detecting VBUS.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The reset manager for is pretty similar to the one for SoCFPGA
cyclone5/arria5 except for a few offsets. This patch adds those offsets.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch removes the optional print_state() function pointer which included
in 'struct extcon_dev' because the extcon must maintain the consistent name
of extcon device on sysfs instead of inconsistent state of external connectors.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>From the usb 3.1 spec available at http://www.usb.org/developers/docs/
table 10-7 (Hub Class Requests) specifies the values for SetHubDepth and
GetPortErrorCount as:
Request bmRequestType bRequest wValue wIndex wLength Data
SetHubDepth 00100000B SET_HUB_DEPTH Hub Depth Zero Zero None
GetPortErrorCount 10100011B GET_PORT_ERR_COUNT Zero Port Two Number of Link Errors on this port
Fix these two values to match the spec.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add inverse unit conversion macro to convert from standard IIO units to
units that might be used by some devices.
Those are useful in combination with scale factors that are specified as
IIO_VAL_FRACTIONAL. Typically the denominator for those specifications will
contain the maximum raw value the sensor will generate and the numerator
the value it maps to in a specific unit. Sometimes datasheets specify those
in different units than the standard IIO units (e.g. degree/s instead of
rad/s) and so we need to do a unit conversion.
From a mathematical point of view it does not make a difference whether we
apply the unit conversion to the numerator or the inverse unit conversion
to the denominator since (x / y) / z = x / (y * z). But as the denominator
is typically a larger value and we are rounding both the numerator and
denominator to integer values using the later method gives us a better
precision (E.g. the relative error is smaller if we round 8000.3 to 8000
rather than rounding 8.3 to 8).
This is where in inverse unit conversion macros will be used.
Marked for stable as used by some upcoming fixes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When compile iio related driver the following warning shown:
include/linux/iio/trigger.h:35:34: warning: 'struct iio_trigger'
declared inside parameter list
int (*set_trigger_state)(struct iio_trigger *trig, bool state);
include/linux/iio/trigger.h:38:18: warning: 'struct iio_dev'
declared inside parameter list
struct iio_dev *indio_dev);
'struct iio_dev' and 'struct iio_trigger' was used before declaration,
forward declaration for these structs to fix warning.
Signed-off-by: Pengyu Ma <pengyu.ma@windriver.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
API. It's a new API that was introduced in 4.2, and we'd like to
avoid ABI change after the release, so it's taken now. As there is no
real in-tree user for this API, it should be fairly safe.
Other than that, the usual small fixes are found in various drivers:
ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=geMs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only bulk changes in this request is ABI updates for ASoC topology
API. It's a new API that was introduced in 4.2, and we'd like to
avoid ABI change after the release, so it's taken now. As there is no
real in-tree user for this API, it should be fairly safe.
Other than that, the usual small fixes are found in various drivers:
ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio"
* tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: topology: Add private data type and bump ABI version to 3
ASoC: topology: Add ops support to byte controls UAPI
ASoC: topology: Update TLV support so we can support more TLV types
ASoC: topology: add private data to manifest
ASoC: topology: Add subsequence in topology
ALSA: hda - one Dell machine needs the headphone white noise fixup
ALSA: fireworks/firewire-lib: add support for recent firmware quirk
Revert "ALSA: fireworks: add support for AudioFire2 quirk"
ASoC: topology: fix typo in soc_tplg_kcontrol_bind_io()
ALSA: HDA: Dont check return for snd_hdac_chip_readl
ALSA: HDA: Fix stream assignment for host in decoupled mode
ASoC: rt5645: Fix lost pin setting for DMIC1
ALSA: oxygen: Fix logical-not-parentheses warning
ASoC: Intel: sst_byt: fix initialize 'NULL device *' issue
ASoC: Intel: haswell: fix initialize 'NULL device *' issue
ASoC: cs4265: Fix setting dai format for Left/Right Justified
Pull drm fixes from Daniel Vetter:
"One i915 regression fix and a drm core one since Dave's not around,
both introduced in 4.2 so not cc: stable.
The fix for the warning Ted reported isn't in here yet since he didn't
yet supply a tested-by and I can't repro this one myself (it's in
fixup code that needs firmware doing something i915 wouldn't do)"
* tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel:
drm/vblank: Use u32 consistently for vblank counters
drm/i915: Allow parsing of variable size child device entries from VBT
In
commit 99264a61df
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 15 19:34:43 2015 +0200
drm/vblank: Fixup and document timestamp update/read barriers
I've switched vblank->count from atomic_t to unsigned long and
accidentally created an integer comparison bug in
drm_vblank_count_and_time since vblanke->count might overflow the u32
local copy and hence the retry loop never succeed.
Fix this by consistently using u32.
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The race condition addressed in commit add05cecef ("mm: soft-offline:
don't free target page in successful page migration") was not closed
completely, because that can happen not only for soft-offline, but also
for hard-offline. Consider that a slab page is about to be freed into
buddy pool, and then an uncorrected memory error hits the page just
after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags &
PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not
necessary because the data on the affected page is not consumed.
To solve it, this patch drops __PG_HWPOISON from page flag checks at
allocation/free time. I think it's justified because __PG_HWPOISON
flags is defined to prevent the page from being reused, and setting it
outside the page's alloc-free cycle is a designed behavior (not a bug.)
For recent months, I was annoyed about BUG_ON when soft-offlined page
remains on lru cache list for a while, which is avoided by calling
put_page() instead of putback_lru_page() in page migration's success
path. This means that this patch reverts a major change from commit
add05cecef about the new refcounting rule of soft-offlined pages, so
"reuse window" revives. This will be closed by a subsequent patch.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen reported the following;
My laptop has been behaving strangely with 4.2-rc2. Once I log
in to my X session, I start getting all kinds of strange errors
from applications and see this in my dmesg:
VFS: file-max limit 8192 reached
The problem is that the file-max is calculated before memory is fully
initialised and miscalculates how much memory the kernel is using. This
patch recalculates file-max after deferred memory initialisation. Note
that using memory hotplug infrastructure would not have avoided this
problem as the value is not recalculated after memory hot-add.
4.1: files_stat.max_files = 6582781
4.2-rc2: files_stat.max_files = 8192
4.2-rc2 patched: files_stat.max_files = 6562467
Small differences with the patch applied and 4.1 but not enough to matter.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Dave Hansen <dave.hansen@intel.com>
Cc: Nicolai Stange <nicstange@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Alex Ng <alexng@microsoft.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By copying BPF related operation to uprobe processing path, this patch
allow users attach BPF programs to uprobes like what they are already
doing on kprobes.
After this patch, users are allowed to use PERF_EVENT_IOC_SET_BPF on a
uprobe perf event. Which make it possible to profile user space programs
and kernel events together using BPF.
Because of this patch, CONFIG_BPF_EVENTS should be selected by
CONFIG_UPROBE_EVENT to ensure trace_call_bpf() is compiled even if
KPROBE_EVENT is not set.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1435716878-189507-3-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stephen Boyd