During igt_reset_nop_engine, it was observed that an unexpected failed
engine reset lead to us busywaiting on the stop-ring semaphore (set
during the reset preparations) on the first request afterwards. There was
no explicit MI_ARB_CHECK in this sequence as the presumption was that
the failed MI_SEMAPHORE_WAIT would itself act as an arbitration point.
It did not in this circumstance, so force it.
This patch is based on the assumption that the MI_SEMAPHORE_WAIT failure
to arbitrate is a rare Tigerlake bug, similar to the lite-restore vs
semaphore issues previously seen in the CS. The explicit MI_ARB_CHECK
should always ensure that there is at least one arbitration point in the
request before the MI_SEMAPHORE_WAIT to trigger the IDLE->ACTIVE event.
Upon processing that event, we will clear the stop-ring flag and release
the semaphore from its busywait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112100759.32698-2-chris@chris-wilson.co.uk
On the off chance that we need to arbitrate before launching the
payload, perform the check after we signal the request is ready to
start. Assuming instantaneous processing of the CS event, the request
will then be treated as having started when we make the decisions as to
how to process that CS event.
v2: More commentary about the users of i915_request_started() as a
reminder about why we are marking the initial breadcrumb.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112100759.32698-1-chris@chris-wilson.co.uk
A new fi-cml-dallium CI machine has 8G and apparently plenty free, yet
fails some selftests with ENOMEM. The failures all seem to be from
huge_gem_object which does not try very hard to allocate memory,
skipping reclaim entirely. Let's try a bit harder and direct reclaim
before failing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112020013.19464-1-chris@chris-wilson.co.uk
The clear-residuals mitigation is a relatively heavy hammer and under some
circumstances the user may wish to forgo the context isolation in order
to meet some performance requirement. Introduce a generic module
parameter to allow selectively enabling/disabling different mitigations.
To disable just the clear-residuals mitigation (on Ivybridge, Baytrail,
or Haswell) use the module parameter: i915.mitigations=auto,!residuals
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1858
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v5.7
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111225220.3483-3-chris@chris-wilson.co.uk
The mitigation is required for all gen7 platforms, now that it does not
cause GPU hangs, restore it for Ivybridge and Baytrail.
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Reviewed-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111225220.3483-2-chris@chris-wilson.co.uk
MEDIA_STATE_VFE only accepts the 'maximum number of threads' in the
range [0, n-1] where n is #EU * (#threads/EU) with the number of threads
based on plaform and the number of EU based on the number of slices and
subslices. This is a fixed number per platform/gt, so appropriately
limit the number of threads we spawn to match the device.
v2: Oversaturate the system with tasks to force execution on every HW
thread; if the thread idles it is returned to the pool and may be reused
again before an unused thread.
v3: Fix more state commands, which was causing Baytrail to barf.
v4: STATE_CACHE_INVALIDATE requires a stall on Ivybridge
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2024
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Randy Wright <rwright@hpe.com>
Cc: stable@vger.kernel.org # v5.7+
Reviewed-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111225220.3483-1-chris@chris-wilson.co.uk
DG1's vswing tables are the same for eDP and HDMI but have slight
differences from ICL/TGL for DP.
v2:
- Use a "_hbr2_hbr3" suffix on the table name to make it more clear
that the same table is used for both HBR2 and HBR3 link rates.
(Swathi)
Bspec: 49291
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108222528.1954514-1-matthew.d.roper@intel.com
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Braswell's pdp workaround is full of dragons, that may be being angered
when they are interrupted. Let's not take that risk and disable
arbitration during the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111105735.21515-1-chris@chris-wilson.co.uk
Some new eDP panels don't like to operate at the max parameters, and
instead we need to go for an optimal confiugration. That unfortunately
doesn't work with older eDP panels which are generally only guaranteed
to work at the max parameters.
To solve these two conflicting requirements let's start with the optimal
setup, and if that fails we start again with the max parameters. The
downside is probably an extra modeset when we switch strategies but
I don't see a good way to avoid that.
For a bit of history we first tried to go for the fast+narrow in
commit 7769db5883 ("drm/i915/dp: optimize eDP 1.4+ link config
fast and narrow"). but that had to be reverted due to regression
on older panels in commit f11cb1c19a ("drm/i915/dp: revert back
to max link rate and lane count on eDP"). So now we try to get
the best of both worlds by using both strategies.
v2: Deal with output_bpp and uapi vs. hw state split
Reword some comments
v3: Rebase
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Cc: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Cc: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=105267
References: https://bugs.freedesktop.org/show_bug.cgi?id=109959
References: https://gitlab.freedesktop.org/drm/intel/issues/272
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107182026.24848-1-ville.syrjala@linux.intel.com
Eliminate checkpatch warnings from intel_cursor.c:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Possible repeated word: 'by'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110175624.3524-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
There was some misinterpretation of specification, when DDIX_USED is
set, the next bit means 0 for DP and 1 for HDMI.
Anyways this misinterpretation is not causing any issues, this change
is just to comply with specification.
Also as for us it do not matters if it is HDMI or DP, not checking the
port type that HTI is using.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108134802.21280-1-jose.souza@intel.com
These error paths return success instead of negative error codes as
intended.
Fixes: c92724de6d ("drm/i915/selftests: Try to detect rollback during batchbuffer preemption")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/X/xMdcewtft7+QFM@mwanda
The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.
The CPU mode takeover code added in commit 5b1ec9ac7a
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".
This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.
Fixes: 5b1ec9ac7a ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com
When wedging the device, we cancel all outstanding requests and mark
them as EIO. Rather than duplicate the small function to do so between
each submission backend, export one.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210109163455.28466-3-chris@chris-wilson.co.uk
drivers/gpu/drm/i915//gt/intel_workarounds.c:1394:20: error: function 'is_nonpriv_flags_valid' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static inline bool is_nonpriv_flags_valid(u32 flags)
This is only used by debug build, so mark it as maybe-unused to keep the
compiler from complaining.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210109163455.28466-2-chris@chris-wilson.co.uk
Inject a fault into lrc_init_wa_ctx() to ensure that we can tolerate a
failure to construct the workarounds.
v2: Avoid mentioning an error for fault-injection, other CI will
complain about the dmesg spam.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210109114453.27798-1-chris@chris-wilson.co.uk
If a request is submitted and known to require no preemption, disable
arbitration around the batch which prevents the HW from handling a
preemption request during the payload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-7-chris@chris-wilson.co.uk
The reason why we did not enable preemption on Broadwater was due to
missing GPGPU workarounds. Since this only applies to rcs0, only
restrict rcs0 (and our global capabilities).
While this does not affect exposing a preemption capability to
userspace, it does affect our internal decisions on whether to use
timeslicing and semaphores between individual engines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-6-chris@chris-wilson.co.uk
We use the completion of the last active breadcrumb to retire the
requests along a timeline. This is purely opportunistic as nothing
guarantees that any particular timeline is terminated by a breadcrumb;
except for parking the engine where we explicitly add a breadcrumb so
that we park quickly and do an explicit retire upon signaling to reduce
the latency dramatically (avoiding a retire worker roundtrip).
With scheduling, we anticipate retiring completed timelines as a matter
of course. Performing the same action from inside the breadcrumbs is
intended to provide similar functionality for legacy ringbuffer
submission.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-5-chris@chris-wilson.co.uk
Before we mark the virtual engine as no longer inflight, flush any
ongoing signaling that may be using the ce->signal_link along the
previous breadcrumbs. On switch to a new physical engine, that link will
be inserted into the new set of breadcrumbs, causing confusion to an
ongoing iterator.
This patch undoes a last minute mistake introduced into commit
bab0557c8d ("drm/i915/gt: Remove virtual breadcrumb before transfer"),
whereby instead of unconditionally applying the flush, it was only
applied if the request itself was going to be reused.
v2: Generalise and cancel all remaining ce->signals
Fixes: bab0557c8d ("drm/i915/gt: Remove virtual breadcrumb before transfer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-4-chris@chris-wilson.co.uk
If any of the perf tests run into 0 time, not only are we liable to
divide by zero, but the result would be highly questionable.
Nevertheless, let's not have a div-by-zero error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-2-chris@chris-wilson.co.uk
On error we unpin and free the wa_ctx.vma, but do not clear any of the
derived flags. During lrc_init, we look at the flags and attempt to
dereference the wa_ctx.vma if they are set. To protect the error path
where we try to limp along without the wa_ctx, make sure we clear those
flags!
Reported-by: Matt Roper <matthew.d.roper@intel.com>
Fixes: 604a8f6f1e ("drm/i915/lrc: Only enable per-context and per-bb buffers if set")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-1-chris@chris-wilson.co.uk
As with the regular suspend paths, also disable the wakeref assertions
as we disable the driver during shutdown.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2899
Fixes: fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104203905.19248-1-chris@chris-wilson.co.uk
This fix bug 210921 where DRM_INFO floods log when hitting an unsupported ASIC in
amdgpu_device_asic_has_dc_support(). This info should be only called once.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210921
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
dc_allow_idle_optimizations() needs to be protected by
CONFIG_DRM_AMD_DC_DCN.
Fixes: 71338cb4a7 ("drm/amd/display: enable idle optimizations for linux (MALL stutter)")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for Renoir.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together.
And the flag "od_enabled" is used to control the overdrive function for
dGPU, like navi10, navi14 and navi21.
APU like Renior or Vangogh uses this "od_enabled" to configure
the frequency range of gfx clock, but the max value of frequency
range will not be higher than the safe limit, it is not "overdrive".
So this patch adds two new flags -- "fine_grain_enabled" and
"fine_grain_started" to avoid this confusion, the flag will
make these two sysfs nodes work separately.
The flag "fine_grain_enabled" is set as "enabled" by default,
so the fine grain tuning function will be enabled by default.
But the flag "fine_grain_started" is set as "false" by default,
so the fine grain function will not take effect until it is set as
"true".
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag "fine_grain_started" will be set as "true",
and the fine grain tuning function will be started.
In other profile modes, including "auto", "high", "low", "profile_peak",
"profile_standard", "profile_min_sclk", "profile_min_mclk",
the flag "fine_grain_started" will be set as "false", and the od range of
fine grain tuning function will be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This pacth is to add the parameters of power profiles for vangogh,
includeing "profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk".
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
psp GFX_CTRL_CMD_ID_CONSUME_CMD different for windows and linux,
according to psp, linux cmds are not correct.
v2: only correct GFX_CTRL_CMD_ID_CONSUME_CMD.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add check for SExSH clients in kfd interrupt handler.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
According to hw, after navi10,it runs in dfll mode, and should
read sclk from AverageGfxclkFrequency.
Signed-off-by: Emily.Deng <Emily.Deng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add one more 2k resolution which appears frequently in market.
Signed-off-by: Emily.Deng <Emily.Deng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need a power_domain wakeref in pps_{lock,unlock} to prevent
a race while resetting pps state in intel_power_sequencer_reset().
intel_power_sequencer_reset() need a pps_mutex to access pps_pipe
but it can't grab pps_mutex due to deadlock with power_well
functions are called while holding pps_mutex.
intel_power_sequencer_reset() is called by power_well function
associated with legacy platforms like vlv and chv therefore re-use
the POWER_DOMAIN_DISPLAY_CORE power domain, which only used
by vlv and chv display power domain.
This will avoids the unnecessary noise of unrelated power wells
in pps_{lock,unlock}.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107112500.16216-1-anshuman.gupta@intel.com
In the next^W future patch, we remove the strict priority system and
continuously re-evaluate the relative priority of tasks. As such we need
to enable the timeslice whenever there is more than one context in the
pipeline. This simplifies the decision and removes some of the tweaks to
suppress timeslicing, allowing us to lift the timeslice enabling to a
common spot at the end of running the submission tasklet.
One consequence of the suppression is that it was reducing fairness
between virtual engines on an over saturated system; undermining the
principle for timeslicing.
v2: Commentary
v3: Commentary for the right cancel_timer()
v4: Add tracing for why we need a timeslice
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2802
Testcase: igt/gem_exec_balancer/fairslice
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107132322.28373-1-chris@chris-wilson.co.uk
Core Changes:
- Lots of drm documentation updates by Simor Ser.
- Require that each crtc has a unique primary plane.
- Add fixme that fbdev_generic_setup is confusing.
Driver Changes:
- Update addresses for TI display drivers maintainers.
- Make DRM_VIRTIO_GPU select VIRTIO.
- Small fixes to qxl, virtio, hisilicon, tve200, panel/s6e63m0.
-----BEGIN PGP SIGNATURE-----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=hp3d
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-01-06' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
Core Changes:
- Lots of drm documentation updates by Simor Ser.
- Require that each crtc has a unique primary plane.
- Add fixme that fbdev_generic_setup is confusing.
Driver Changes:
- Update addresses for TI display drivers maintainers.
- Make DRM_VIRTIO_GPU select VIRTIO.
- Small fixes to qxl, virtio, hisilicon, tve200, panel/s6e63m0.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fdfbfd7a-b91d-3f59-11c8-984704ce0ee1@linux.intel.com
Commit 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
added an intel_dsi_msleep() helper which skips sleeping if the
MIPI-sequences have a version of 3 or newer and the panel is in vid-mode;
and it moved a bunch of msleep-s over to this new helper.
This was based on my reading of the big comment around line 730 which
starts with "Panel enable/disable sequences from the VBT spec.",
where the "v3 video mode seq" column does not have any wait t# entries.
Given that this code has been used on a lot of different devices without
issues until now, it seems that my interpretation of the spec here is
mostly correct.
But now I have encountered one device, an Acer Aspire Switch 10 E
SW3-016, where the panel will not light up unless we do actually honor the
panel_on_delay after exexuting the MIPI_SEQ_PANEL_ON sequence.
What seems to set this model apart is that it is lacking a
MIPI_SEQ_DEASSERT_RESET sequence, which is where the power-on
delay usually happens.
Fix the panel not lighting up on this model by using an unconditional
msleep(panel_on_delay) instead of intel_dsi_msleep() when there is
no MIPI_SEQ_DEASSERT_RESET sequence.
Fixes: 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118124058.26021-1-hdegoede@redhat.com
- Reduce stack usage in ipu-di.
- Fix imx-ldb for compile tests.
- Make drm encoder control functions optional.
- Add drm managed variants drmm_encoder_alloc(),
drmm_simple_encoder_alloc(), drmm_universal_plane_alloc(), and
drmm_crtc_alloc_with_planes() for drm_encoder_init(),
drm_simple_encoder_init(), drm_universal_plane_init(), and
drm_crtc_init_with_planes(), respectively.
- Update imx-drm to use the new functions for drm managed resource
allocation, moving initialization from bind to probe where possible.
- Fix imx-tve clock provider leak.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCX/M62RcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwPdlAP4/zZ401iFrj+ZiRTYFNGHaRrBI
ldQ97lk2Ndzgp5tHzQD/dsAMFymw5+fYlp2xa25kB4LQJLzOC+KzlZwFKF5W4QM=
=I3bV
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2021-01-04' of git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: fixes and drm managed resources
- Reduce stack usage in ipu-di.
- Fix imx-ldb for compile tests.
- Make drm encoder control functions optional.
- Add drm managed variants drmm_encoder_alloc(),
drmm_simple_encoder_alloc(), drmm_universal_plane_alloc(), and
drmm_crtc_alloc_with_planes() for drm_encoder_init(),
drm_simple_encoder_init(), drm_universal_plane_init(), and
drm_crtc_init_with_planes(), respectively.
- Update imx-drm to use the new functions for drm managed resource
allocation, moving initialization from bind to probe where possible.
- Fix imx-tve clock provider leak.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[danvet: Fix conflict between doc changes by both Philipp and Simon
Ser, see 9999587b68 ("drm: rework description of primary and cursor
planes")]
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/c745fc1596898932c9454fd2979297b4242566a2.camel@pengutronix.de
Add support for DP-HDMI2.1 PCON
From the series cover letter:
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfdpndkt.fsf@intel.com
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
-----BEGIN PGP SIGNATURE-----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=orEC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-12-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
The bspec has been updated with new vswing programming for RKL DP. No
data is provided for HDMI or eDP, so for now we'll continue to assume
that those are the same as TGL.
Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218040535.45492-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
This reverts commit a135a1b4c4.
This leads to blank screens on some boards after replugging a
display. Revert until we understand the root cause and can
fix both the leak and the blank screen after replug.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211033
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1427
Cc: Stylon Wang <stylon.wang@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Andre Tomt <andre@tomt.net>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
AFter detecting a register mismatch between the protocontext and the
image generated by HW, immediately break out of the double loop.
Otherwise we end up with a second confusing error message.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210106123939.18435-1-chris@chris-wilson.co.uk
Chris Wilson