The commit 318c3e15cd
added some "fck" clock alias to timer devices that are
not needed anymore since hwmod framework will create
them automatically.
A warning was added to highlight and thus fix the redundancy.
[ 0.616424] omap_timer.1: alias fck already exists
[ 0.621948] omap_timer.2: alias fck already exists
[ 0.627380] omap_timer.3: alias fck already exists
[ 0.632781] omap_timer.4: alias fck already exists
[ 0.638214] omap_timer.5: alias fck already exists
[ 0.643615] omap_timer.6: alias fck already exists
[ 0.649078] omap_timer.7: alias fck already exists
[ 0.654479] omap_timer.8: alias fck already exists
[ 0.659881] omap_timer.9: alias fck already exists
[ 0.665283] omap_timer.10: alias fck already exists
[ 0.670776] omap_timer.11: alias fck already exists
Remove all the clkdev entries for timer fck alias.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The parent clock of the OCP_ABE_ICLK is the AESS_FCLK and the
parent clock of the AESS_FCLK is the ABE_FCLK...
ABE_FCLK --> AESS_FCLK --> OCP_ABE_ICLK
The AESS_FCLK and OCP_ABE_ICLK clocks both have dividers which
determine their operational frequency. However, the dividers for
the AESS_FCLK and OCP_ABE_ICLK are controlled via a single bit,
which is the CM1_ABE_AESS_CLKCTRL[24] bit. When this bit is set to
0, the AESS_FCLK divider is 1 and the OCP_ABE_ICLK divider is 2.
Similarly, when this bit is set to 1, the AESS_FCLK divider is 2
and the OCP_ABE_ICLK is 1.
The above relationship between the AESS_FCLK and OCP_ABE_ICLK
dividers ensure that the OCP_ABE_ICLK clock is always half the
frequency of the ABE_CLK...
OCP_ABE_ICLK = ABE_FCLK/2
The divider for the OCP_ABE_ICLK is currently missing so add a
divider that will ensure the OCP_ABE_ICLK frequency is always half
the ABE_FCLK frequency.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4460 specific clocks are not getting added as the
cpu_is_omap44xx is choosing only OMAP4430 specific clock nodes.
Changing it to add to OMAP4460 specific clocks also.
This is clocks are required of temperature sensor.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Cc: paul@pwsan.com
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 DPLL_ABE can enable a 4X multipler on top of the normal MN multipler
and divider. This is achieved by setting CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN
bit in CKGEN module of CM1. From the OMAP4 TRM:
Fdpll = Fref x 2 x (4 x M/(N+1)) in case REGM4XEN bit field is set (only
applicable to DPLL_ABE).
Add new round_rate() and recalc() functions for OMAP4, that check the
setting of REGM4XEN bit and handle this appropriately. The new functions
are a simple wrapper on top of the existing omap2_dpll_round_rate() and
omap2_dpll_get_rate() functions to handle the REGM4XEN bit.
The REGM4XEN bit is only implemented for the ABE DPLL on OMAP4 and so
only dpll_abe_ck uses omap4_dpll_regm4xen_round_rate() and
omap4_dpll_regm4xen_recalc() functions.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed attempt to return a negative from a fn returning
unsigned; pass along errors from omap2_dpll_round_rate();
added documentation; added Jon's S-o-b]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add device name to OMAP2 dmtimer fclk nodes so that the fclk nodes can be
retrieved by doing a clk_get with the corresponding device pointers or
device names.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
[tony@atomide.com: fixed typo in email address]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warning:
arch/arm/mach-omap2/clock44xx_data.c: In function 'omap4xxx_clk_init':
arch/arm/mach-omap2/clock44xx_data.c:3371:6: warning: 'cpu_clkflg' may be used uninitialized in this function
The approach taken here is intended to work if omap4xxx_clk_init() is
converted into an initcall.
Thanks to Bjarne Steinsbo <bsteinsbo@gmail.com> for proposing another
approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Bjarne Steinsbo <bsteinsbo@gmail.com>
After commit 665d001338 ("OMAP2+: hwmod:
Follow the recommended PRCM module enable sequence"), device drivers
for OMAP IP blocks that do not use runtime PM can cause oopses or
kernel instability[1][2].
This is because those non-runtime PM drivers do not use the hwmod
code, which implements the correct IP block enable and disable
sequence.
Several options for dealing with this problem have been proposed:
1. Add a new field to the OMAP struct clk to mark clocks that are
currently used by non-runtime PM drivers. Modify the clock code to
use the old clockdomain sequence for these marked clocks. As
drivers are converted to use runtime PM, remove the annotation from
the clocks.
2. Similar to #1, but associate the flag with the struct omap_clk
instead.
3. Add IDLEST wait support to the OMAP4 clock code, similar to the way
it is implemented for OMAP2/3, and enable it in each struct clk
currently used by non-runtime PM drivers. As drivers are converted
to use runtime PM, remove the annotation from the clocks.
4. Do nothing; leave the problem to those responsible for the
unconverted drivers.
5. Re-enable clock-based clockdomain control in the OMAP4 clock code.
This would revert back to the behavior of Linux 3.0, simply with a
slightly longer module enable/disable latency.
Unfortunately, no approach seemed particularly good. Options 1
through 3 seemed unwise due to the following reasons:
A. The OMAP struct clks are intended primarily to describe hardware
clock nodes, and the intention is that no driver-specific data
should be stored there (applies to #1)
B. The resulting patch would have been quite large for the -rc series
(applies to #1, #2, #3)
C. The patch would have been a new, yet temporary hack; and similar fixes
have drawn negative comments in the recent past (see for example [3])
Option 4 is undesirable because commit
665d001338 ("OMAP2+: hwmod: Follow the
recommended PRCM module enable sequence") has resulted in a less
stable kernel; and kernel stability is more important than OMAP4 power
management.
Option 5 is the approach taken in this patch. This seemed to be the
least intrusive approach for 3.1-rc.
The approach in this patch was originally proposed by Ohad Ben-Cohen
<ohad@wizery.com>. I'm simply writing the commit message and passing
it along.
...
Thanks to Luciano Coelho <coelho@ti.com> for reporting the problem.
Thanks to Ohad Ben-Cohen <ohad@wizery.com> for tracking the problem
down, generating a temporary workaround, and proposing a patch to deal
with the problem. Thanks to Rajendra Nayak <rnayak@ti.com> for
proposing another patch to deal with the problem. Thanks to Felipe
Balbi <balbi@ti.com> for comments.
1. Coelho, Luciano <coelho@ti.com>. _Re: Oops on ehci_hcd when
booting 3.0.0-rc2 on panda_. Tue, 09 Aug 2011 14:26:08 +0300.
Posted to the <linux-omap@vger.kernel.org> mailing list. Available
from (among others)
http://www.spinics.net/linux/lists/linux-omap/msg55213.html
2. Munegowda, Keshava <keshava_mgowda@ti.com>. _Re: Oops on ehci_hcd
when booting 3.0.0-rc2 on panda_. Thu, 11 Aug 2011 13:51:05 +0530.
Posted to the <linux-omap@vger.kernel.org> mailing list. Available
from (among others)
http://www.spinics.net/linux/lists/linux-omap/msg55371.html
3. King, Russell <linux@arm.linux.org.uk>. _Re: [PATCH 5/8] OMAP4:
PM: TEMP: Prevent l3init from idling/force sleep_. Thu, 23 Jun
2011 16:22:49 +0100. Posted to the <linux-omap@vger.kernel.org>
mailing list. Available from (among others)
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg51392.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
MAINTAINERS: add maintainer of CSR SiRFprimaII machine
ARM: CSR: initializing L2 cache
ARM: CSR: mapping early DEBUG_LL uart
ARM: CSR: Adding CSR SiRFprimaII board support
OMAP4: clocks: Update the clock tree with 4460 clock nodes
OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
OMAP4: ID: add omap_has_feature for max freq supported
OMAP: ID: introduce chip detection for OMAP4460
ARM: Xilinx: merge board file into main platform code
ARM: Xilinx: Adding Xilinx board support
Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
On OMAP4, the PRCM recommended sequence for enabling
a module after power-on-reset is:
-1- Force clkdm to SW_WKUP
-2- Enabling the clocks
-3- Configure desired module mode to "enable" or "auto"
-4- Wait for the desired module idle status to be FUNC
-5- Program clkdm in HW_AUTO(if supported)
This sequence applies to all older OMAPs' as well,
however since they use autodeps, it makes sure that
no clkdm is in IDLE, and hence not requiring a force
SW_WKUP when a module is being enabled.
OMAP4 does not need to support autodeps, because
of the dyanamic dependency feature, wherein
the HW takes care of waking up a clockdomain from
idle and hence the module, whenever an interconnect
access happens to the given module.
Implementing the sequence for OMAP4 requires
the clockdomain handling that is currently done in
clock framework to be done as part of hwmod framework
since the step -4- above to "Wait for the desired
module idle status to be FUNC" is done as part of
hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[b-cousson@ti.com: Adapt it to the new clkdm hwmod attribute and API]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: dropped mach-omap2/clock.c changes; modified to only
call the clockdomain code if oh->clkdm is set; disable clock->clockdomain
interaction on OMAP4]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 the auxclk nodes (part of SCRM) support both
divider as well as parent selection.
Supporting this requires splitting the existing nodes
(which support only parent selection) into two nodes,
one for parent and another for divider selection.
The nodes for parent selection are named auxclk*_src_ck
and the ones for divider selection as auxclk*_ck.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[b-cousson@ti.com: Rebase on top of clock cleanup
and autogen alignement]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Extend the existing function to create clkdev for every optional
clocks to add a well one "fck" alias for the main_clk of the
omap_hwmod.
It will allow to remove these static clkdev entries from the
clockXXX_data.c file.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Todd Poynor <toddpoynor@google.com>
[paul@pwsan.com: remove all of the "fck" role clkdev aliases from the
clock data files; fixed error message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, CPU accesses on unmapped addresses are redirected to GPMC by
L3 interconnect. Because of CPU speculative nature, such accesses are
possible which can lead to indirect access to GPMC and if it's clock is
not running, it can result in hang/abort on the platform.
Above makes access to GPMC unpredictable during the execution, so it's
module mode needs to be kept under hardware control instead of software
control.
Since the auto gating is supported for GPMC, there isn't any power impact
because of this change.
The issue was un-covered with security middleware running along with HLOS.
In this case GPMC had a valid MMU descriptor on secure side where as HLOS
didn't map the GMPC because it isn't being used.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[b-cousson@ti.com: Update subject and fix typos in the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing DSS optional clocks to HWMOD data for OMAP4xxx.
Add HWMOD_CONTROL_OPT_CLKS_IN_RESET flag for dispc to fix dispc reset.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[b-cousson@ti.com: Remove a comment and update the subject]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: removed DSS "fck" role and some clkdev aliases at Tomi's
request]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
UNIPRO was removed from OMAP4 devices from ES2.0 onwards.
Since this IP was anyway non-functional and not supported,
it is best to remove it completely.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[b-cousson@ti.com: Update the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: split PRCM header file changes into a separate patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
McASP2, 3 and MMC6 modules are not present in the OMAP4 family.
Remove the fclk and the clksel related to these nodes.
Rename the references that were potentially re-used in order nodes.
Remove related macros in prcm header files.
Update TI copyright date.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[b-cousson@ti.com: Update the patch according to autogen output]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: split PRCM data changes into a separate patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The DPLL USB can generate higher speed (x2) than the regular ones.
The max multiplication value is then twice the previous value.
Fix both max_mult and max_div with that correct values.
Change the max_div variable type to u16 to allow storing up to 256.
Replace as well the define with the value to avoid
unneeded indirection and provide a better readability.
Remove the defines that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A couple of fieds were edited manually and thus do not stick
to the template used by the generator and by other structures.
Move them to the correct location.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: dropped the UNIPRO changes since those will be removed
in a later patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
usb_host_fs_fck does have a clkdev mapping with "usbhs-omap.0"
and "fs_fck" alias used by the driver.
The entry with NULL dev is thus not needed anymore.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The USB DPLL is a J-Type DPLL with the sddiv extra parameter. Add it
in USB DPLL.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: dropped UNIPRO change since it is removed in a later patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the new clock nodes (bandgap_ts_fclk, div_ts_ck) for omap4460.
Handle these nodes using the clock flags (CK_*).
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSS driver has used fck and ick clocks on OMAP2/3 to get DSS HW up and
running, and also to get the pixel clock's source clock rate from the
fck.
On OMAP4 the clock data is set up in a different way, as there's no ick,
dss_fck points to a fake clock which just affects DSS's MODULEMODE, and
dss_dss_clk if the DSS_FCK.
>From DSS driver's point of view the dss_fck sounds like an ick, and
dss_dss_clk is the fck. While this is not entirely correct from HW point
of view, especially for the ick, configuring the clock aliases that way
makes DSS "just work" with OMAP4's clock setup.
In the (hopefully near) future DSS driver will be reworked to use
pm_runtime support which should clean up the clock code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
DSS code uses ick as one of the clocks in clk_get/clk_put. OMAP4 clock database
doesn't have ick for DSS, so adding ick as dummy clock.
This is needed for backward compatibility with OMAP2/3.
Once pm_runtime* APIs get introduced in DSS, this will be revisited.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, clock database has <dev, clock-name> tuples for DSS2. Because of
this, the clock names are different across different OMAP platforms.
This patch aligns the DSS2 clock names and roles across OMAP 2420, 2430, 3xxx,
44xx platforms in the clock databases, hwmod databases for opt-clocks, and DSS
clock handling.
This ensures that clk_get/put/enable/disable APIs in DSS can use uniform role
names.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devices of clocks are set to usbhs, so that
only usbhs common driver can invoke these clocks.
The dummy per port clocks are added to omap3
clock data base. This helps to invoke common
clock get APIs for omap3 and omap4.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable autoidle on all clocks during clock framework initialization.
(If CONFIG_PM is set, autoidle is re-enabled for all clocks later in
the boot process.)
The principle behind this patch, and some similar patches, is that the
kernel should start with all power management features disabled.
Later in the boot process, the PM code, if compiled in with CONFIG_PM,
enables or re-enables power management features.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Enable hardware gate control for all dpll MX and X2 postdividers.
This requires the allow_idle/deny_idle functions to be
populated for all clock nodes (mx/x2 post dividers) in
clkops.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
All OMAP3/4 dpll's support hardware level autogating.
Populate allow_idle/deny_idle function pointers for all
DPLL's in clkops.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A few headers are included twice, remove them.
Found the following errors using make includecheck:
arch/arm/mach-omap2/clock44xx_data.c: prm44xx.h is
included more than once.
arch/arm/mach-omap2/clockdomains44xx_data.c: cm1_44xx.h
is included more than once.
arch/arm/mach-omap2/clockdomains44xx_data.c: cm2_44xx.h
is included more than once.
arch/arm/mach-omap2/powerdomain2xxx_3xxx.c: prm-regbits-34xx.h
is included more than once.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[paul@pwsan.com: dropped lists from patch cc:s; tweaked subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
The following OMAP4 clocks have the following fixed divisors that
determine the frequency at which these clocks operate. These
dividers are defined by the PRCM specification and without these
dividers the rates of the below clocks are calculated incorrectly.
This may cause internal peripherals using these clocks to operate
at the wrong frequency.
- abe_24m_fclk (freq = divided-by-8)
- ddrphy_ck (freq = parent divided-by-2)
- dll_clk_div_ck (freq = parent divided-by-2)
- per_hs_clk_div_ck (freq = parent divided-by-2)
- usb_hs_clk_div_ck (freq = parent divided-by-3)
- func_12m_fclk (freq = parent divided-by-16)
- func_24m_clk (freq = parent divided-by-4)
- func_24mc_fclk (freq = parent divided-by-8)
- func_48mc_fclk (freq = divided-by-4)
- lp_clk_div_ck (freq = divided-by-16)
- per_abe_24m_fclk (freq = divided-by-4)
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
L3INSTR clock domain is read only register and its reset value is
HW_AUTO. The modules withing this clock domain needs to be kept under
hardware control.
MODULEMODE:
- 0x0: Module is disable by software. Any INTRCONN access to module
results in an error, except if resulting from a module wakeup
(asynchronous wakeup).
- 0x1: Module is managed automatically by hardware according to
clock domain transition. A clock domain sleep transition put
module into idle. A wakeup domain transition put it back
into function. If CLKTRCTRL=3, any INTRCONN access to module
is always granted. Module clocks may be gated according to
the clock domain state.
This patch keeps CM_L3INSTR_L3_3_CLKCTRL, CM_L3INSTR_L3_INSTR_CLKCTRL
and CM_L3INSTR_INTRCONN_WP1_CLKCTRL module mode under hardware control
by using ENABLE_ON_INIT flag.
Without this the OMAP4 device OFF mode SAR restore phase aborts during
interconnect register restore phase. This can be also handled by doing
explicit a clock enable and disable in the low power code since there
is no direct module associated with it. But that seems not necessary
since the clock domain is under HW control.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In omap4, there is no explicit configuration register to enable mailbox clocks.
Defining dummy clock for mailbox clock module to keep the mailbox driver
backward compatible with previous omaps.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
J-Type DPLLs have additional configuration parameters that need to
be programmed when setting the multipler and divider for the DPLL.
These parameters being the sigma delta divider (SD_DIV) for the DPLL
and the digital controlled oscillator (DCO) to be used by the DPLL.
The current code is implemented specifically to configure the
OMAP3630 PER J-Type DPLL. The OMAP4430 USB DPLL is also a J-Type DPLL
and so this code needs to be updated to work for both OMAP3 and OMAP4
devices and any other future devices that have J-TYPE DPLLs.
For the OMAP3630 PER DPLL both the SD_DIV and DCO paramenters are
used but for the OMAP4430 USB DPLL only the SD_DIV field is used.
The current implementation will only program the SD_DIV and DCO
fields if the DPLL has both and hence this does not work for
OMAP4430.
In order to make the code more generic add two new fields to the
dpll_data structure for the SD_DIV field and DCO field bit-masks
and only program these fields if the masks are defined for a specific
DPLL. This simplifies the code and allows us to remove the flag
DPLL_NO_DCO_SEL.
Tested on OMAP36xx Zoom3 and OMAP4 Blaze.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: removed explicit inlining and added '_' prefix on lookup_*()
functions; added testing info to commit message; added 35xx comments back in]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix opt clocks name in clock framework and hwmod.
Add the missing iclk in the ocp_if structure.
Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to ensure
the the GPIO optional clock is enable during reset.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Charulatha V <charu@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The CORE and PER M3 post dividers are different from the rest of the
DPLL post dividers as in they go to SCRM, and are used
there to export clocks for instance used by external sensor.
There is no automatic HW dependency in PRCM to manage them. Hence these
two clocks (dpll post dividers) should be managed by SW and explicitly
enabled/disabled.
Add control in clock framework to handle that.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add support for auxiliary clocks nodes which are part of SCRM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add register address, mask and link to the clksel structure that
were missing in the IVA DPLL mux clock node.
Signed-off-by: Jonathan Bergsagel <jbergsagel@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch extends the OMAP4 clock data to include
various x2 clock nodes between DPLL and HS dividers as the
clock framework skips a x2 while calculating the dpll locked
frequency.
The clock database extensions are autogenerated using
the scripts maintained by Benoit Cousson.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: fixed merge conflicts against v2.6.37-rc5; dropped
dpll_mpu_x2_ck on advice from Benoît]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The gating of pad_clks and slimbus_ck is controlled by the PRCM, but
since the clock source is external, this is the SW responsability
to gate / un-gate it when the mcpdm or slimbus module need to be used.
There is no autogating possible with such external clock.
Add SW control to enable / disable this SW gating in the pad_clks_ck
and slimbus_clk clock node.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Benoit Cousson