Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default. The system
must request a VLAN tag packet filter to get packets with that tag.
Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.
This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.
Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().
Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In XL710 devices we program FD filter's fields from Tx perspective of the flow.
However the user interface exposed in ethtool should be compliant with the
previous generation of drivers where a filter src and dst field are from
the RX perspective. This patch changes the ethtool interface in this regard
to match the other drivers.
Change-ID: Iec6ccddd87357c4fb53ccf33aa0fae699faf70cf
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add set_pf_context, replace set_phy_reset with set_phy_debug, add
nvm_config_read/write, remove nvm_read/write_reg_se and add some
PHY types.
With these changes we bump the API version to 1.2.
Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.
Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch separates the hardware logic from the set function, so that
we can re-use it during a ptp_reset. This enables the reset to return
functionality to the last known timestamp mode, rather than resetting
the value. We initialize the mode to off during the ptp_init cycle.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return a 0 directly rather than a constant.
Reported-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc
architecture. Rename this #define in xgbe.h to avoid the
redefined warning issued during compilation.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_addr_t for DMA address parameters and u32 for shared memory
offset parameters.
Do not assume that dma_addr_t is the same as unsigned long; it will
not be in PAE configurations. Truncate DMA addresses to 32 bits when
printing them. This is OK because the DMA mask for this device is
32-bit (per default).
Also rename the DMA address parameters from 'skb' to 'dma'.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commit befdf89 "net/mlx4_core: Preserve pci_dev_data after
__mlx4_remove_one()", there are two mlx4 pci callbacks which will
attempt to release the mlx4_priv object -- .shutdown and .remove.
This leads to a use-after-free access to the already freed mlx4_priv
instance and trigger a "Kernel access of bad area" crash when both
.shutdown and .remove are called.
During reboot or kexec, .shutdown is called, with the VFs probed to
the host going through shutdown first and then the PF. Later, the PF
will trigger VFs' .remove since VFs still have driver attached.
Fix that by keeping only one driver entry which releases mlx4_priv.
Fixes: befdf89 ('net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()')
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hypervisor driver tracks free slots and reserved slots at the global level
and tracks allocated slots and guaranteed slots per VF.
Guaranteed slots are treated as reserved by the driver, so the total
reserved slots is the sum of all guaranteed slots over all the VFs.
As VFs allocate resources, free (global) is decremented and allocated (per VF)
is incremented for those resources. However, reserved (global) is never changed.
This means that effectively, when a VF allocates a resource from its
guaranteed pool, it is actually reducing that resource's free pool (since
the global reserved count was not also reduced).
The fix for this problem is the following: For each resource, as long as a
VF's allocated count is <= its guaranteed number, when allocating for that
VF, the reserved count (global) should be reduced by the allocation as well.
When the global reserved count reaches zero, the remaining global free count
is still accessible as the free pool for that resource.
When the VF frees resources, the reverse happens: the global reserved count
for a resource is incremented only once the VFs allocated number falls below
its guaranteed number.
This fix was developed by Rick Kready <kready@us.ibm.com>
Reported-by: Rick Kready <kready@us.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logical conjunction always evaluates to false: minor < 2 && minor > 1
I guess what you wanted is rather: minor > 2 || minor < 1
This was partly found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
A check on a memory allocation is checked incorrectly.
This was partly found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following compilation warning:
[...]
CC drivers/net/phy/amd-xgbe-phy.o
drivers/net/phy/amd-xgbe-phy.c:1353:30: warning:
‘amd_xgbe_phy_ids’ defined but not used [-Wunused-variable]
static struct mdio_device_id amd_xgbe_phy_ids[] = {
^
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug that shows up with recv window sizes that exceed the size of
the RCV_BUFSIZ field in opt0 (>= 1024K). If the recv window exceeds
this, then we specify the max possible in opt0, add add the rest in via
a RX_DATA_ACK credits.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select the appropriate hw mtu index and initial sequence number to optimize
hw memory performance.
Add new cxgb4_best_aligned_mtu() which allows callers to provide enough
information to be used to [possibly] select an MTU which will result in the
TCP Data Segment Size (AKA Maximum Segment Size) to be an aligned value.
If an RTR message exhange is required, then align the ISS to 8B - 1 + 4, so
that after the SYN the send seqno will align on a 4B boundary. The RTR
message exchange will leave the send seqno aligned on an 8B boundary.
If an RTR is not required, then align the ISS to 8B - 1. The goal is
to have the send seqno be 8B aligned when we send the first FPDU.
Based on original work by Casey Leedom <leeedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently indirect interrupts for RDMA CQs funnel through the LLD's RDMA
RXQs, which also handle direct interrupts for offload CPLs during RDMA
connection setup/teardown. The intended T4 usage model, however, is to
have indirect interrupts flow through dedicated IQs. IE not to mix
indirect interrupts with CPL messages in an IQ. This patch adds the
concept of RDMA concentrator IQs, or CIQs, setup and maintained by the
LLD and exported to iw_cxgb4 for use when creating CQs. RDMA CPLs will
flow through the LLD's RDMA RXQs, and CQ interrupts flow through the
CIQs.
Design:
cxgb4 creates and exports an array of CIQs for the RDMA ULD. These IQs
are sized according to the max available CQs available at adapter init.
In addition, these IQs don't need FL buffers since they only service
indirect interrupts. One CIQ is setup per RX channel similar to the
RDMA RXQs.
iw_cxgb4 will utilize these CIQs based on the vector value passed into
create_cq(). The num_comp_vectors advertised by iw_cxgb4 will be the
number of CIQs configured, and thus the vector value will be the index
into the array of CIQs.
Based on original work by Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OZao
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.16:
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller"
* tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (95 commits)
mmc: sdhci-s3c: use mmc_of_parse and remove the card_tasklet
mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller
mmc: sdhci-of-esdhc: Fixup compile error
mmc: tegra: fix reporting of base clock frequency
mmc: tegra: disable UHS modes
mmc: sdhci-dove: use mmc_of_parse() and remove card_tasklet CD handler
MAINTAINERS: mmc: Add path to git tree
mmc: dove: fix missing MACH_DOVE dependency
mmc: sdhci: SD tuning is broken for some controllers
mmc: sdhci-esdhc-imx: fix mmc ddr mode regression issue
mmc: sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
mmc: omap_hsmmc: split omap-dma header file
mmc: omap_hsmmc: fix cmd23 multiblock read/write
mmc: omap_hsmmc: use devm_ioremap_resource
mmc: omap_hsmmc: use devm_request_threaded_irq
mmc: omap_hsmmc: use devm_request_irq
mmc: omap_hsmmc: use devm_clk_get
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
mmc: wmt-sdmmc: Use GFP_KERNEL instead of hard-coded value
mmc: omap: Use DIV_ROUND_UP instead of open coded
...
- Add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- Fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- A pile of SRP initiator fixes from Bart Van Assche.
- Fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- The usual fixes and cleanups to mlx4, mlx5, cxgb4 and other
low-level drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wcdc
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull main InfiniBand/RDMA updates from Roland Dreier:
- add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- a pile of SRP initiator fixes from Bart Van Assche.
- fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- the usual fixes and cleanups to mlx4, mlx5, cxgb4 and other low-level
drivers.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (61 commits)
RDMA/cxgb4: Add support for iWARP Port Mapper user space service
RDMA/nes: Add support for iWARP Port Mapper user space service
RDMA/core: Add support for iWARP Port Mapper user space service
IB/mlx4: Fix gfp passing in create_qp_common()
IB/umad: Fix use-after-free on close
IB/core: Fix kobject leak on device register error flow
RDMA/cxgb4: add missing padding at end of struct c4iw_alloc_ucontext_resp
mlx4_core: Fix GFP flags parameters to be gfp_t
IB/core: Fix port kobject deletion during error flow
IB/core: Remove unneeded kobject_get/put calls
IB/core: Fix sparse warnings about redeclared functions
IB/mad: Fix sparse warning about gfp_t use
IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
IB: Add a QP creation flag to use GFP_NOIO allocations
IB: Return error for unsupported QP creation flags
IB: Allow build of hw/ and ulp/ subdirectories independently
mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
RDMA/cxgb4: Add missing padding at end of struct c4iw_create_cq_resp
IB/srp: Avoid problems if a header uses pr_fmt
IB/umad: Fix error handling
...
Bumpity and Fred Worm say it's time to change the numbers again.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I658731d022ea23cedede4be2bfecd8b4cc68d270
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We tell the HW upper boundary of power of 2 in VSI config,
but the HW does not restrict us to use just power of 2 GPS in
case of RSS as long as we are not sharing the RSS table with
another VSI (VMDq). We at present are not doing RSS in VMDq
VSI.
If we were to enable that and if the system had CPU count which
was not power 2, the VMDq VSIs will see a little skewed distribution.
Change-ID: I3ea797ce9065a3ca4fc4d04251bf195463410473
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete all the old and stale MAC filters for the VF VSI when the host
administrator changes the VF MAC address from under its feet. Also don't
bother to add a filter for the VSI when its going to go away anyway.
Just record the new address and punch the VF reset.
Change-ID: Ic0d12055926f41989d1965ccf500053729c063ad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FD_SB and FD_ATR needs to be checked independently in order to decide if
we will support multiple queues or not.
Change-ID: I9d3274f5924c79e29efdbcf66a2fcca1fee2107f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not marking packets with bad checksums
correctly, especially IPv6 packets with a bad checksum.
To do this correctly we need a define that may be set by
hardware in rare cases.
Change-ID: I1a997b72b491ded27a78ac3bce1197b2d2611130
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the logic in i40e_determine_queue_usage() so that
SR-IOV doesn't get turned off unnecessarily.
Change-ID: I86ca304fa9f742a50e9ea831b887f358a6a9d53d
Signed-off-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way resources are distributed to special features.
Change-ID: I847e49d714a1d70e97f3f994cb39bfb5e02ab016
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware supports VF antispoofing for both MAC addresses and VLANs.
Enable this feature by default for all VFs and implement the netdev op
to control it from the command line.
Change-ID: Ifb941da22785848aa3aba6b2231be135b8ea8f31
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to complain in the log about mac addresses that
can't be deleted because they don't exist.
Change-ID: I4e6370df175bf72726f06d2206c03bcbfded8387
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was a vestige of early driver development that no longer
has any actual use.
Change-ID: I95b5b19c4bbfaff8759197af671ebaf716cb6ab5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of VSIs that the firmware reports to us is a guaranteed
minimum, not an absolute maximum. The hardware actually supports far
more than the reported value, which we often need.
To allow for this, we allocate space for a larger number of VSIs than is
guaranteed by the firmware, with the knowledge that we may fail to get
them all in the future.
Note that we are just allocating pointers here, the actual (much larger)
VSI structures are allocated on demand.
Change-ID: I6f4e535ce39d3bf417aef78306e04fbc7505140e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix function header comment to have the correct function name.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for error status bits on the AdminQ event queue and announce them
if seen. If the Firmware sets these bits, it will trigger an AdminQ
interrupt to get the driver's attention to process the ARQ, which will
likely be enough to clear the actual issue.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I009e0ebc8be764e40e193b29aed2863f43eb5cb0
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-06-06
Please accept this batch of fixes intended for the 3.16 stream.
For the bluetooth bits, Gustavo says:
"Here some more patches for 3.16. We know that Linus already opened the merge
window, but this is fix only pull request, and most of the patches here are
also tagged for stable."
Along with that, Andrea Merello provides a fix for the broken scanning
in the venerable at76c50x driver...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.
See commit f87e6f4793 ("net: dont leave active on stack LIST_HEAD")
In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Bump i40e to 0.4.5 and i40evf to 0.9.29.
Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove two device IDs 1582 and 1573, because they will not be shipped.
Change-ID: Ica2e550b5b21a69e3f353eba2fe5e1c532a548c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a coding error where during the registration for NAPI
the driver requested 256 budget. The max recommended
value for this is NAPI_POLL_WEIGHT or 64.
Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TSO logic in the transmit path had some assumptions that
have been broken now that the kernel can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.
This fixes the assumptions and allows the kernel to operate
as efficiently as possible with both SENDFILE and SEND.
In addition, the hardware limit of data contained in a descriptor is
changed to the next power of two below where it currently is in
order to align to a power of two value, preventing a single byte
of data in a descriptor.
Change-ID: I6af1f0b87c1458e10644dbd47541591075a52651
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.
Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.
Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once more, with feeling: not all VSIs have rings. To assume so is to
invite null pointers to your party.
Change-ID: I576858824468d9712d119fa1015a1f28c27712c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Be sure to clear PXE mode bit on each reset after AdminQ has been rebuilt.
Change-ID: I992d8c79594f8ca0660c50844ace675ecb9c9bf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where FD SB/ATR and NTUPLE configurations status are
reported erroneously. Without this patch, driver reports FDir without further
information.
Change-ID: I5bdd2871b7f2db1e5f5e76c741ae6a0dc603b453
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The correct format is %pM, not %pMAC.
Change-ID: Idb335723a966fe56db3a72b9c07c08ca66f9db3c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up inconsistent log messages, mostly related to punctuation. Based
on the dogma that "kernel messages are not sentences", remove all
trailing periods. Reword a few of the messages to make them less
sentence-like.
Change-ID: Ibd849aa7623a77549b0709988c66ab05d1311472
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.
Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.
Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. There is no ixgbe_watchdog_task function in the driver, so change
the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
because it is never used.
3. Remove some TBD comments that are not needed.
Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove use of registers no longer supported.
Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.
This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.
CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use an extra state variable to keep track of when the IRQs are fully
set up. This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.
Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up. We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.
Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver should print link messages like all the
other Intel Ethernet drivers.
Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing unicast, multicast, and broadcast stats for the port.
Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx.
Stop printing the netdev multicast value because it doesn't include Tx
and would be confusing.
Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The wait time was originally too optimistic and the resets were failing
after EMPR. This increases the loop count to wait considerably longer.
This won't delay the actual wait longer than really needed, just allows
us to poll more times as needed.
Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.
Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.
Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.
Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware are not expected to work correctly
with revision_id 0 hardware. Don't prevent the user from
using it, but be sure to print a warning.
Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the VEB statistics in the ethtool stats output.
Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.
Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial platform driver for the AMD
10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/amd/hplance.h:
#define HPLANCE_MEMOFF 0x8000 /* struct lance_init_block */
#define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */
The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine. Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000A/DM9000B force the initial check of the link status. The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in. This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DM9000 uses level-triggered interrupts. Some systems (PXA270) only
support edge-triggered interrupts on GPIOs. Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.
* Make some helper functions called dm9000_mask_interrupts() and
dm9000_unmask_interrupts() for readability.
* dm9000_init_dm9000(): ensure that this function always leaves interrupts
masked regardless of the state when it entered the function. This is
primarily to support the situation in dm9000_open where the logic used
to go:
dm9000_open()
dm9000_init_dm9000()
unmask interrupts
request_irq()
If an interrupt occurred between unmasking the interrupt and
requesting the irq, it would be missed forever as the edge event would
never be seen by the GPIO hardware in the PXA270. This allows us to
change the logic to:
dm9000_open()
dm9000_init_dm9000()
dm9000_mask_interrupts()
request_irq()
dm9000_unmask_interrupts()
* dm9000_timeout(), dm9000_drv_resume(): Add the missing
dm9000_unmask_interrupts() now required by the change above.
* dm9000_shutdown(): Use mask helper function
* dm9000_interrupt(): Use mask/unmask helper functions
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset
* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
was called immediately before-hand. Bring dm9000_reset into
dm9000_init_dm9000.
* The following commit updated the dm9000_probe reset routine to use NCR_RST
| NCR_MAC_LBK:
6741f40 DM9000B: driver initialization upgrade
and a later commit added a bug-fix to always reset the chip twice:
09ee9f8 dm9000: Implement full reset of DM9000 network device
Unfortunately, since the changes in 6741f40 were made by replacing the
dm9000_probe dm9000_reset with the adjusted iow(), the changes in
09ee9f8 were not incorporated into the dm9000_probe reset.
Furthermore, it bypassed the requisite reset-delay causing some boards
to get at least one "read wrong id ..." dev_err message during
dm9000_probe.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM. In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit (a02eb4 "xen-netback: worse-case estimate in xenvif_rx_action is
underestimating") capped the slot estimation to MAX_SKB_FRAGS, but that triggers
the next BUG_ON a few lines down, as the packet consumes more slots than
estimated.
This patch introduces full_coalesce on the skb callback buffer, which is used in
start_new_rx_buffer() to decide whether netback needs coalescing more
aggresively. By doing that, no packet should need more than
(XEN_NETIF_MAX_TX_SIZE + 1) / PAGE_SIZE data slots (excluding the optional GSO
slot, it doesn't carry data, therefore irrelevant in this case), as the provided
buffers are fully utilized.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Uninitialzed fields in mailbox command structure
caused commands to time out randomly due to garbage
values so initialize it to zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().
Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."
So call netif_carrier_off() prior to register_netdev().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 3afc2167f6 scan in not
working anymore, due to mac80211 requires rx frequency status
information.
This patch makes the driver report this information.
While NOT scanning this is straightforward.
While scanning the firmware performs RF sweep and we cannot track
the actual tuning frequency, so this is guessed by parsing beacons
and probe responses.
This should be enough for ensuring functionality.
Thanks-to: Johannes Berg <johannes@sipsolutions.net> [ for suggestions and reviewing ]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.
Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.
Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.
Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.
Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.
Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.
Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.
Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.
Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware requires descriptors to be allocated in groups of 32.
Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.
The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.
Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused defines and macros for RX_LRO.
Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We introduced this check in case this structure changed in the future,
the AQ definition is now mature enough that this check is no longer necessary.
Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register range, being subject to register diagnostic, can vary among
different NVMs. We will try to identify the full range and use it for
a register test. This is needed to avoid false test results. If we fail
to define the proper register range we will test only the first register
from that group.
Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A couple of FD checks ended up using bitwise OR to check
a value, which ends up always being evaluated to true.
This should fix the issue. Thanks to DaveJ for noticing
and reporting the issue!
CC: Dave Jones <davej@redhat.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added VXLAN link configuration for sending UDP checksums, and allowing
TX and RX of UDP6 checksums.
Also, call common iptunnel_handle_offloads and added GSO support for
checksums.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core irq updates from Thomas Gleixner:
"The irq department delivers:
- Another tree wide update to get rid of the horrible create_irq
interface along with its even more horrible variants. That also
gets rid of the last leftovers of the initial sparse irq hackery.
arch/driver specific changes have been either acked or ignored.
- A fix for the spurious interrupt detection logic with threaded
interrupts.
- A new ARM SoC interrupt controller
- The usual pile of fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
Documentation: brcmstb-l2: Add Broadcom STB Level-2 interrupt controller binding
irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller
genirq: Improve documentation to match current implementation
ARM: iop13xx: fix msi support with sparse IRQ
genirq: Provide !SMP stub for irq_set_affinity_notifier()
irqchip: armada-370-xp: Move the devicetree binding documentation
irqchip: gic: Use mask field in GICC_IAR
genirq: Remove dynamic_irq mess
ia64: Use irq_init_desc
genirq: Replace dynamic_irq_init/cleanup
genirq: Remove irq_reserve_irq[s]
genirq: Replace reserve_irqs in core code
s390: Avoid call to irq_reserve_irqs()
s390: Remove pointless arch_show_interrupts()
s390: pci: Check return value of alloc_irq_desc() proper
sh: intc: Remove pointless irq_reserve_irqs() invocation
x86, irq: Remove pointless irq_reserve_irqs() call
genirq: Make create/destroy_irq() ia64 private
tile: Use SPARSE_IRQ
tile: pci: Use irq_alloc/free_hwirq()
...
To make TLB mode work, the patch allows learning packets
to be sent using mac addresses assigned to macvlan devices,
also taking into an account vlans that may be between the
bond and macvlan device.
To make RLB work, all we have to do is accept ARP packets
for addresses added to the bond dev->uc list. Since RLB
mode will take care to update the peers directly with
correct mac addresses, learning packets for these addresses
do not have be send to switch.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding and team drivers generate specific events during failover
that trigger switch updates. When a macvlan device is configured
on top of bonding, we want switches to learn about the macvlan
devices as well. This patch adds a handler to macvlan driver to
propagate these events to all macvlan devices. We let the generic
inetdev event handler do the work.
This allows macvlan to operated correctly over active-backup
mode bond.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding devices manage the unicast filters of the underlying
interfaces, but do not turn on IFF_UNICAST_FLT flag. Thus
anytime a unicast address is added to the bond, the bond is
places in promiscuous mode.
Turn on IFF_UNICAST_FLT on the bond device so that the bond does
not go into promiscuous mode needlesly. If an underlying device
does not support unicast filtering, that device will automaticall
enter promiscuous mode already.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following
WARNING is occured:
LD drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in
reference from the function gfar_probe() to the function
.init.text:gfar_init_addr_hash_table()
The function gfar_probe() references
the function __init gfar_init_addr_hash_table().
This is often because gfar_probe lacks a __init
annotation or the annotation of gfar_init_addr_hash_table is wrong.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build on the refactoring of the previous patch to implement multiple
queues between xen-netfront and xen-netback.
Check XenStore for multi-queue support, and set up the rings and event
channels accordingly.
Write ring references and event channels to XenStore in a queue
hierarchy if appropriate, or flat when using only one queue.
Update the xennet_select_queue() function to choose the queue on which
to transmit a packet based on the skb hash result.
Signed-off-by: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for multi-queue support in xen-netfront, move the
queue-specific data from struct netfront_info to struct netfront_queue,
and update the rest of the code to use this.
Also adds loops over queues where appropriate, even though only one is
configured at this point, and uses alloc_etherdev_mq() and the
corresponding multi-queue netif wake/start/stop functions in preparation
for multiple active queues.
Finally, implements a trivial queue selection function suitable for
ndo_select_queue, which simply returns 0, selecting the first (and
only) queue.
Signed-off-by: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Builds on the refactoring of the previous patch to implement multiple
queues between xen-netfront and xen-netback.
Writes the maximum supported number of queues into XenStore, and reads
the values written by the frontend to determine how many queues to use.
Ring references and event channels are read from XenStore on a per-queue
basis and rings are connected accordingly.
Also adds code to handle the cleanup of any already initialised queues
if the initialisation of a subsequent queue fails.
Signed-off-by: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for multi-queue support in xen-netback, move the
queue-specific data from struct xenvif into struct xenvif_queue, and
update the rest of the code to use this.
Also adds loops over queues where appropriate, even though only one is
configured at this point, and uses alloc_netdev_mq() and the
corresponding multi-queue netif wake/start/stop functions in preparation
for multiple active queues.
Finally, implements a trivial queue selection function suitable for
ndo_select_queue, which simply returns 0 for a single queue and uses
skb_get_hash() to compute the queue index otherwise.
Signed-off-by: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This array was allocated separately in commit ac3d5ac2 ("xen-netback:
fix guest-receive-side array sizes") due to it being very large, and a
struct xenvif is allocated as the netdev_priv part of a struct
net_device, i.e. via kmalloc() but falling back to vmalloc() if the
initial alloc. fails.
In preparation for the multi-queue patches, where this array becomes
part of struct xenvif_queue and is always allocated through vzalloc(),
move this back into the struct xenvif.
Signed-off-by: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, igb and ixgbe.
Emil provides his version 2 fix for the detection of SFP+ capable interfaces.
In cases where the driver is loaded while there are no SFP+ modules in cage,
the interface was not being detected as SFP capable. Resolve the issue by
identifying interfaces with no PHY type set as SFP capable which allows the
driver to detect the SFP module when the interface is brought up. In this
version 2 of the patch, the 82599 specific check was removed since we only
have 82598 devices that are SFP capable.
Jacob removes the including of the export header in the ixgbe PTP core, since
it is not needed. Renames igb_ptp_enable() to igb_ptp_feature_enable() to
better reflect the actual functions purpose.
Todd fixes the ethtool loopback test for i354 backplane devices since we
do not know what PHY is to be used for the devices, use MAC loopback for
ethtool tests. Todd also sets the packet buffer size register defaults for
i210 devices.
Yongjian Xu removes the check for skb->len being negative or zero since there
is never a case where it would be zero or negative for e1000.
Manuel Schölling updates e1000 to use the time_after() helper function.
v2: Fix indentation on wrapped line in patch 3 of the series based on
feedback from David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise sparse gives a bunch of warnings like
drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: sparse: incorrect type in argument 4 (different base types)
drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: expected int [signed] gfp
drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: got restricted gfp_t
Signed-off-by: Roland Dreier <roland@purestorage.com>
- ACPICA update to upstream version 20140424. That includes a
number of fixes and improvements related to things like GPE
handling, table loading, headers, memory mapping and unmapping,
DSDT/SSDT overriding, and the Unload() operator. The acpidump
utility from upstream ACPICA is included too. From Bob Moore,
Lv Zheng, David Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices
rather than PNP devices for ACPI device objects with _HID by
default. PNP devices will still be created for the ACPI device
object with device IDs corresponding to real PNP devices, so
that change should not break things left and right, and we're
expecting to see more and more ACPI-enumerated platform devices
in the future. From Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing
it to handle system suspend/resume on Asus T100 correctly.
From Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions
if certain additional conditions related to coordination within
device hierarchy are met. Related PM documentation update and
ACPI PM domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling,
Tony Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from
Chander Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie,
Doug Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from
Jacob Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way
from Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tpdF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into next
Pull ACPI and power management updates from Rafael Wysocki:
"ACPICA is the leader this time (63 commits), followed by cpufreq (28
commits), devfreq (15 commits), system suspend/hibernation (12
commits), ACPI video and ACPI device enumeration (10 commits each).
We have no major new features this time, but there are a few
significant changes of how things work. The most visible one will
probably be that we are now going to create platform devices rather
than PNP devices by default for ACPI device objects with _HID. That
was long overdue and will be really necessary to be able to use the
same drivers for the same hardware blocks on ACPI and DT-based systems
going forward. We're not expecting fallout from this one (as usual),
but it's something to watch nevertheless.
The second change having a chance to be visible is that ACPI video
will now default to using native backlight rather than the ACPI
backlight interface which should generally help systems with broken
Win8 BIOSes. We're hoping that all problems with the native backlight
handling that we had previously have been addressed and we are in a
good enough shape to flip the default, but this change should be easy
enough to revert if need be.
In addition to that, the system suspend core has a new mechanism to
allow runtime-suspended devices to stay suspended throughout system
suspend/resume transitions if some extra conditions are met
(generally, they are related to coordination within device hierarchy).
However, enabling this feature requires cooperation from the bus type
layer and for now it has only been implemented for the ACPI PM domain
(used by ACPI-enumerated platform devices mostly today).
Also, the acpidump utility that was previously shipped as a separate
tool will now be provided by the upstream ACPICA along with the rest
of ACPICA code, which will allow it to be more up to date and better
supported, and we have one new cpuidle driver (ARM clps711x).
The rest is improvements related to certain specific use cases,
cleanups and fixes all over the place.
Specifics:
- ACPICA update to upstream version 20140424. That includes a number
of fixes and improvements related to things like GPE handling,
table loading, headers, memory mapping and unmapping, DSDT/SSDT
overriding, and the Unload() operator. The acpidump utility from
upstream ACPICA is included too. From Bob Moore, Lv Zheng, David
Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices rather
than PNP devices for ACPI device objects with _HID by default. PNP
devices will still be created for the ACPI device object with
device IDs corresponding to real PNP devices, so that change should
not break things left and right, and we're expecting to see more
and more ACPI-enumerated platform devices in the future. From
Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing it
to handle system suspend/resume on Asus T100 correctly. From
Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions if
certain additional conditions related to coordination within device
hierarchy are met. Related PM documentation update and ACPI PM
domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling, Tony
Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from Chander
Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie, Doug
Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from Jacob
Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way from
Thomas Renninger"
* tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (187 commits)
ACPICA: Namespace: Remove _PRP method support.
intel_pstate: Improve initial busy calculation
intel_pstate: add sample time scaling
intel_pstate: Correct rounding in busy calculation
intel_pstate: Remove C0 tracking
PM / hibernate: fixed typo in comment
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPI / scan: use platform bus type by default for _HID enumeration
ACPI / scan: always register ACPI LPSS scan handler
ACPI / scan: always register memory hotplug scan handler
ACPI / scan: always register container scan handler
ACPI / scan: Change the meaning of missing .attach() in scan handlers
ACPI / scan: introduce platform_id device PNP type flag
ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
ACPI / PNP: use device ID list for PNPACPI device enumeration
ACPI / scan: .match() callback for ACPI scan handlers
ACPI / battery: wakeup the system only when necessary
power_supply: allow power supply devices registered w/o wakeup source
...
Pull trivial tree changes from Jiri Kosina:
"Usual pile of patches from trivial tree that make the world go round"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
staging: go7007: remove reference to CONFIG_KMOD
aic7xxx: Remove obsolete preprocessor define
of: dma: doc fixes
doc: fix incorrect formula to calculate CommitLimit value
doc: Note need of bc in the kernel build from 3.10 onwards
mm: Fix printk typo in dmapool.c
modpost: Fix comment typo "Modules.symvers"
Kconfig.debug: Grammar s/addition/additional/
wimax: Spelling s/than/that/, wording s/destinatary/recipient/
aic7xxx: Spelling s/termnation/termination/
arm64: mm: Remove superfluous "the" in comment
of: Spelling s/anonymouns/anonymous/
dma: imx-sdma: Spelling s/determnine/determine/
ath10k: Improve grammar in comments
ath6kl: Spelling s/determnine/determine/
of: Improve grammar for of_alias_get_id() documentation
drm/exynos: Spelling s/contro/control/
radio-bcm2048.c: fix wrong overflow check
doc: printk-formats: do not mention casts for u64/s64
doc: spelling error changes
...
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no case skb->len would be 0 or 'negative'.
Remove the check.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the defaults on probe for the packet buffer size registers for the
i210.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't know what PHY is to be used for i354 backplane, so use MAC
loopback for ethtool tests.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The name igb_ptp_enable is not synonymous with the purpose of this
function, so rename it to better explain its purpose.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need this header file, so we shouldn't be including it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where the driver is loaded while there are no SFP+ modules in
the cage the interface was not being detected as SFP capable. To account
for this the driver called identify_sfp in ixgbe_get_settings to make
sure the data is correct. However when there is no SFP+ module in the cage
the driver waits for the I2C reads to time out which can take more than a
second and will cause issues with tools (like net-snmp) that may poll
for that information.
This patch resolves the issue by identifying interfaces with no PHY
type set as SFP capable which allows the driver to detect the SFP module
when the interface is brought up. As result of this we can also remove the
identify_sfp call from ixgbe_get_settings.
v2: remove the 82599 specific check since we have 82598 devices that are SFP
capable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4a55530f38 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support. Add the missing entries using the data
from before that commit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.
This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:
net eth0: Receive FIFO Overflow
Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).
I have tested the RMCR_RNC configuration with NFS root filesystem and
the driver has not failed yet. There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.
There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.
Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rmb() is required to ensure that the CQE is not read before it
is written by the adapter DMA. PCI ordering rules will make sure
the other fields are written before the marker at the end of struct
eth_fast_path_rx_cqe but without rmb() a weakly ordered processor can
process stale data.
Without the barrier we have observed various crashes including
bnx2x_tpa_start being called on queues not stopped (resulting in message
start of bin not in stop) and NULL pointer exceptions from bnx2x_rx_int.
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When injecting EEH error to bnx2x adapter, adapter couldn't be recovery
and caused recursive EEH errors. The patch fixes the issue.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As smsc driver supports carrier detection, it should unset NOCARRIER
flag only after carrier state determination. By default that flag
is off so driver should set it before starting auto-negotiation
Signed-off-by: Balakumaran <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/resource_size.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work better
now that it has been reworked to do per-port power control dynamically.
There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
is finally gone now that everything has been converted over to the
dynamic debug inteface, the last hold-out drivers were cleaned up and
the config option removed. There were also other minor things all
through the drivers/usb/ tree, the shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
c4AAoMHR2kb62U1plylLbPnboQTjfcl0
=fG6y
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next
Pull USB driver updates from Greg KH:
"Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work
better now that it has been reworked to do per-port power control
dynamically. There's also a raft of gadget driver updates and fixes,
CONFIG_USB_DEBUG is finally gone now that everything has been
converted over to the dynamic debug inteface, the last hold-out
drivers were cleaned up and the config option removed. There were
also other minor things all through the drivers/usb/ tree, the
shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms"
* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
USB: orinoco_usb: remove CONFIG_USB_DEBUG support
USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
USB: media: streamzap: remove CONFIG_USB_DEBUG
USB: media: redrat3: remove CONFIG_USB_DEBUG usage
USB: media: redrat3: remove unneeded tracing macro
usb: qcserial: add additional Sierra Wireless QMI devices
usb: host: max3421-hcd: Use module_spi_driver
usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
usb: qcserial: add Netgear AirCard 341U
Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
usb: host: xhci-plat: add xhci_plat_start()
usb: host: max3421-hcd: Fix potential NULL urb dereference
Revert "usb: gadget: net2280: Add support for PLX USB338X"
USB: usbip: remove CONFIG_USB_DEBUG reference
USB: remove CONFIG_USB_DEBUG from defconfig files
usb: resume child device when port is powered on
usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
...
Add support for the hix5hd2 XGMAC 1Gb ethernet device.
The controller requires two queues for tx and two queues for rx.
Controller fetch buffer from free queue and then push to used queue.
Diver should prepare free queue and free buffer from used queue.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iSCSI netlink message needs to be sent before the ulp_ops is cleared
as it is sent through a function pointer in the ulp_ops. This bug
causes iscsid to not get the message when the bnx2i driver is unloaded.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are allocating memory with GFP_KERNEL under spinlock. Since this is
the only call manipulating the cnic_udev_list and it is always under
rtnl_lock, cnic_dev_lock can be safely removed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the called function, such as bnx2fc_indicate_netevent(), can sleep,
we cannot take rcu_lock(). To prevent the rcu protected ulp_ops from going
away, we use the cnic_lock mutex and set the ULP_F_CALL_PENDING flag.
The code already waits for ULP_F_CALL_PENDING flag to clear in
cnic_unregister_device().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cd11cf5053 I accidentally
added an error message. I used it for debugging and forgot to remove
it before submitting the patch.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 5bbde4d2ec ("net: fec: use pinctrl PM helpers") caused the following
build error on m68k:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_open':
drivers/net/ethernet/freescale/fec_main.c:1819:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_close':
drivers/net/ethernet/freescale/fec_main.c:1863:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
In order to fix the build error, include the linux/pinctrl/consumer.h header
file.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ec_bhf driver is specific to the Beckhoff CX embedded PC series.
These are based on Intel x86 CPU. So we can add a dependency on
X86, with COMPILE_TEST as an alternative to still allow for broader
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Darek Marcinkiewicz <reksio@newterm.pl>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a jiffies hack we can use the standard api for delays.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix:
CC drivers/net/ethernet/broadcom/bcmsysport.o
In file included from drivers/net/ethernet/broadcom/bcmsysport.c:28:0:
drivers/net/ethernet/broadcom/bcmsysport.h:41:8: error: redefinition of 'struct tsb'
arch/sparc/include/asm/mmu_64.h:65:8: note: originally defined here
make[1]: *** [drivers/net/ethernet/broadcom/bcmsysport.o] Error 1
we change struct tsb to struct bcm_tsb in the broadcom driver in
order to avoid the namespace collision. For consistency, we also
change struct rsb to struct bcm_rsb, so the Rx/Tx symmetry is
maintained.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding proper stop/wake thresholds, we can expect a queue to never
be full and drop the NETDEV_TX_BUSY return path. In any case, if the queue
cannot accommodate a TSO packet, the packet would be discarded.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the current dropped packet count by doing it properly,
increasing the count when a packet is discarded; i.e. the packet is not
processed and the driver returns NETDEV_TX_OK.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This is true only for the last fragment of the packet.
This is wrong, however, since every descriptor buffer is DMA mapped and needs
to be unmapped.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iPad model has a different product id, this patch adds support for iPad 2
(pid 0x12a2) and iPad 3 (pid 0x12a6). Note that iPad 2 must be jailbroken and a
third-party app must be used for tethering to work. On iPad 3, tethering works
out of the box (assuming your ISP is nice).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netpoll support to macvlan devices. Based on the netpoll support in the 802.1q vlan code.
Tested and macvlan could work well with netconsole.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The min_tx_pkt variable decides the cutoff point where the driver
will stop padding out NTBs to maximum size. The padding is a tradeoff
where we use some USB bus bandwidth to allow the device to receive
fixed size buffers. Different devices will have different optimal
settings, spanning from no padding at all to padding every NTB.
There is no way to automatically figure out which setting is best
for a specific device.
The default value is a reasonable tradeoff, calculated based on the
USB packet size and out NTB max size. This may have to be changed
along with any tx_max changes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mandatory GetNtbParameters control request is an important part of
the host <-> device protocol negotiation in CDC NCM (and CDC MBIM). It
gives device limits which the host must obey when configuring the
protocol aggregation variables. The driver will enforce this by
rejecting attempts to set any of the tunable variables to a value
which is not supported by the device. Exporting the parameter block
helps userspace decide which values are allowed without resorting
to trial and error.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool coalesce API is not applicable for this driver. Forcing
it to fit the NCM aggregation redefined the API in a driver specific
way, which is much worse than defining a clean new API. These ethtool
coalesce functions have therefore been replaced by a new sysfs API.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach a driver specific sysfs group to the netdev, and use it
for the rx/tx aggregation variables.
The datagram aggregation defined by the CDC NCM specification is
specific to this device class (including CDC MBIM). Using the
ethtool interrupt coalesce API as an interface to the aggregation
parameters redefined that API in a driver specific and confusing
way. A sysfs group
- makes it clear that this is a driver specific userspace API, and
- allows us to export the real values instead of some translated
version, and
- lets us include more aggregation variables which were impossible
to force into the ethtool API.
Additionally, using sysfs allows tuning the driver on space
constrained hosts where userspace tools like ethtool are undesired.
Suggested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't matter whether the buffer size goes up or down. We have to
keep usbnet and device syncronized to be able to split transfers at the
correct boundaries. The spec allow skipping short packets when using
max sized transfers. If we don't tell usbnet about our new expected rx
buffer size, then it will merge and/or split NTBs. The driver does not
support this, and the result will be lots of framing errors.
Fix by always reallocating usbnet rx buffers when the rx_max value
changes.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are calling usbnet_start_xmit() to flush any remaining data,
depending on the side effect that tx_curr_skb is set to NULL,
ensuring a new allocation using the updated tx_max. But this
side effect will only happen if there were any cached data ready
to transmit. If not, then an empty tx_curr_skb is still allocated
using the old tx_max size. Free it to avoid a buffer overrun.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cloning the big skbs we use for USB buffering chokes up TCP and
SCTP because the socket memory limits are hitting earlier than
they should. It is better to unconditionally copy the unwrapped
packets to freshly allocated skbs.
Reported-by: Jim Baxter <jim_baxter@mentor.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvlan dev should always have the same mac address like lowerdev
when in the passthru mode, change the mac address alone will break the
work mechanism, so when the lowerdev or macvlan mac address changes,
we should propagate the changes to another dev.
v1->v2: Allow macvlan dev to change mac address for passthru mode and propagate to
lowerdev.
v2->v3: Don't set the mac address to the lower dev's unicast address for
passthru mode when mac address changes.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive. Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Now it is not possible to set mtu to team device which has a port
enslaved to it. The reason is that when team_change_mtu() calls
dev_set_mtu() for port device, notificator for NETDEV_PRECHANGEMTU
event is called and team_device_event() returns NOTIFY_BAD forbidding
the change. So fix this by returning NOTIFY_DONE here in case team is
changing mtu in team_change_mtu().
Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch moved device tree interrupt resolution into
platform_get_irq_byname:
ad69674 of/irq: do irq resolution in platform_get_irq_byname()
As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:
http://lists.linaro.org/pipermail/kernel-build-reports/2014-May/003659.html
This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface is unusable, as the cdc-wdm character device doesn't reply to
any QMI command. Also, the out-of-tree Sierra Wireless GobiNet driver fully
skips it.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-06-02
Please pull this remaining batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"The remainder for -next right now is mostly fixes, and a handful of
small new things like some CSA infrastructure, the regdb script mW/dBm
conversion change and sending wiphy notifications."
For the bluetooth bits, Gustavo says:
"Some more patches for 3.16. There is nothing really special here, just a
bunch of clean ups, fixes plus some small improvements. Please pull."
For the nfc bits, Samuel says:
"We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning fixes"
For the atheros bits, Kalle says:
"Ben added support for setting antenna configurations. Michal improved
warm reset so that we would not need to fall back to cold reset that
often, an issue where ath10k stripped protected flag while in monitor
mode and made module initialisation asynchronous to fix the problems
with firmware loading when the driver is linked to the kernel.
Luca removed unused channel_switch_beacon callbacks both from ath9k and
ath10k. Marek fixed Protected Management Frames (PMF) when using Action
Frames. Also we had other small fixes everywhere in the driver."
Along with that, there are a handful of updates to a variety
of drivers. This includes updates to at76c50x-usb, ath9k, b43,
brcmfmac, mwifiex, rsi, rtlwifi, and wil6210.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls. Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.
Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.
This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.
commit cab6715c3e
Author: Yang Wei <Wei.Yang@windriver.com>
Date: Sun May 25 09:53:44 2014 +0800
net: driver: stmicro: Remove some useless the lock protection
This introduced the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
context imbalance in 'stmmac_get_pauseparam' -
different lock contexts for basic block
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 70a640d0da
("net/mlx4_en: Use affinity hint") and commit
c8865b64b0 ("cpumask: Utility function
to set n'th cpu - local cpu first") because these changes break
the build when SMP is disabled amongst other things.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf.
Kevin updates the i40e and i40evf driver i40e_check_asq_alive() to ensure
the length register offset is non-zero which indicates that the software
has initialized the admin queue. Also removes PCTYPE definitions which are
now reserved.
Mitch enables descriptor prefetch for rings belonging to the virtual function.
Also configures the VF minimum transmit rate to 50 Mbps rather than 0 which was
be interpreted as no limit at all. Mitch found in order for the VF to achieve
its programmed transmit rate, we need to set the max credit value to 4.
Lastly fixes a Tx hang and firmware crash that happens after setting the MTU
on a VF by not using the RESETTING state during reinit, this is because
the RESETTING state means that a catastrophic hardware bad thing is happening
and the driver needs to tiptoe around and not use the admin queue or registers.
A reinit is no big deal and we can use the admin queue (and we should) so
do not set the state to RESETTING during reinit to resolve the bug.
Akeem changes the declaration of the transmit and receive rings inside
several loops to eliminate declaring the same ring every time for the
duration of the loop and declares them just once before the loop. Also fixes
the driver to clear the recovery pending bit if pf_reset fails instead of
falling through the setup process.
Anjali makes a change based on feedback from Ben Hutchings that cmd->data
needs to be reported in ETHTOOL_GRXCLSRLCNT and use a helper function to
calculate the total filter count.
Jesse removes storm control since the storm control features are not apart
of the hardware and were mistakenly left in the code.
Greg changes tx_lpi_status and rx_lpi_status from bool to u32 to avoid
sparse errors.
Shannon adds the clear_pxe AdminQ API call to tell the firmware that the
driver is taking over from PXE. In addition, relaxes the firmware API
check to allow more flexibility in handling newer NICs and NVMs in the field.
Vasu ensures that FCoE is disabled for MFP modes since it is not supported
by overriding the hardware FCoE capability.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlOFkZ4ACgkQjTAFq1RaXHOYCQCeJwwa8XQMw2HkGemGMBSpcUHb
MLwAoISCoqgrXWq/lBBzDqlVXik8fR4t
=gHVg
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.15-20140528' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-05-28
here's a pull request for v3.15, hope it's not too late.
Oliver Hartkopp fixed a bug in the CAN led trigger device renaming code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCC async event processing code has 2 issues:
a) because of long struct names the code indentation is badly broken
b) description and definitions of how an MCC completion is interpreted as
an async event are confusing (for e.g. the last word of an MCC event is
named "code", while "code" is just a sub-field of the last word.)
This patch fixes the structure definitions, comments and re-factors code
as needed.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some FW cmds, the caller just issues the cmd and doesn't wait for a
response. The response handling is done in the MCCQ compl processing context
only. Move this code into a separate routine to make be_mcc_compl_process()
more manageable.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves MCCQ error status handling in the following ways:
a) A MCC cmd completion returns a base-status and an addl-status.
So far, the routine be_mcc_compl_process() returned only the "status" value.
Now, embedd both statuses in the return value and let the caller routine access
the value of interest using base_status() and addl_status() macros.
b) Rename variables accordingly (base/addl) to avoid confusion while error
checking.
b) Some of the errors returned by FW are harmless and so an error msg is not
logged for such errors. Capture this logic in a separate routine to make the
code more readable.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain new flash regions have been added to Skyhawk-R FW image. The newer
FW images specify op_types for each region. A region is flashed only
when it's CRC doesn't match that of the region on the HW flash. While
upgrading to a new FW image the driver is expected to tolerate certain
errors.
This patch re-factors code under be_flash() to support the above scheme.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R FW supports TX-rate setting only as a % value of the link
speed, set via the SET_PROFILE_CONFIG cmd.
This patch makes the necessary changes to the FW cmd descriptors to support
the above change and also introduces checks in be_set_vf_tx_rate() to allow
only discrete values (that map to % of the link-speed).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set mc-promisc (multicast promiscuous) mode on an interface, only if it is
*not already* in that mode.
Also removed logs that report interface being set to multicast
promiscous mode. In an earlier comment on the netdev list such log messages
were deemed unnecessary as this behaviour is common across most of the
ethernet drivers.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero it again in the driver.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use is_zero_ether_addr() to check for the MAC address being all zeros instead of
open coding the check.
Also use ether_addr_copy() instead of a manual memcpy() to set the
netdev->dev_addr.
Furthermore, get rid of a redundant assignment of netdev->addr_len. This is
already set by ether_setup() which is called in tile_net_setup().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x development team has transferred from Broadcom to Qlogic.
This patch updates some obsolete email addresses to usable ones.
The bnx2x files contain headers with legal information from
Broadcom. Qlogic Legal depratment is taking their time coming up
with their own legal info. So this patch only updates contact
information. I will follow up with a patch for the headers once I
have the required info.
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the GIDs assigned to a VF in the port RoCE GID table when
that guest goes down (either crashes or goes down cleanly).
As part of this fix, we refactor the RoCE gid table driver copy,
moving it to the mlx4_port_info structure (together with the MAC
and VLAN tables).
As with the MAC and VLAN tables, we now use a mutex per port
for the GID table so that modifying the driver copy and
modifying the firmware copy of a port GID table becomes an
atomic operation (thus avoiding driver-copy/FW-copy mismatches).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggreagation of version 1-2 because of version 1 can hit
PLB errors too. If it's not set so we missing events for PLB bits
and driver can't process those interrupts.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chips of emac/rgmii b'000' for 0/1 channel isn't suitable which
resulted in non working network interface in this mode.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Division of a 32 bit number by a 64 bit number causes the following link
error introduced by
7c2ce6e60f "enic: Add support for adaptive interrupt coalescing"
drivers/built-in.o: In function `enic_poll_msix':
enic_main.c:(.text+0x48710a): undefined reference to `__udivdi3'
make: *** [vmlinux] Error 1
Since numerator is 32 bit, convert denominator to 32 bit accordingly.
Fixes: 7c2ce6e60f ("enic: Add support for adaptive interrupt coalescing")
Reported-by: Jim Davis <jim.epost@gmail.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlOC70IACgkQjTAFq1RaXHPjywCcCrq9+i+L9ZF9vgSBymcXz6ml
RToAnRUwc6O5htRG85AMefZaed3Drz4C
=3xv6
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.16-20140526' of git://gitorious.org/linux-can/linux-can-next
Add new xilinx CAN driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Compile-Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of MLX4_QP_ST_MLX in verify_qp_parameters() was
accidentally put inside the inner switch statement (that handles which
transition of RC/UC/XRC QPs is happening). Fix this by moving the case
to the outer switch statement.
The compiler pointed this out with:
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'verify_qp_parameters':
>> drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2875:3: warning: case value '7' not in enumerated type 'enum qp_transition' [-Wswitch]
case MLX4_QP_ST_MLX:
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 99ec41d0a4 ("mlx4: Add infrastructure for selecting VFs to enable QP0 via MLX proxy QPs")
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print message if no events received. This should not happen.
If it is, it points to the problem in firmware.
Track also cases when multiple events processed in one IRQ
Print information as soon as possible - mbox pointers and
event header right after reading it. This helps to identify potential
problem with memory allocation for the event buffer.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This commit adds the sysfs interface for enabling QP0 on VFs for
selected VF/port.
By default, no VFs are enabled for QP0 operation.
To enable QP0 operation on a VF/port, under
/sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries:
- smi_enabled (read-only). Indicates whether smi is currently
enabled for the indicated VF/port
- enable_smi_admin (rw). Used by the admin to request that smi
capability be enabled or disabled for the indicated VF/port.
0 = disable, 1 = enable.
The requested enablement will occur at the next reset of the
VF (e.g. driver restart on the VM which owns the VF).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.
Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs. As such, they operate over VL15. Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).
Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context). Thus, non-enabled VFs will not pose a security
risk. The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.
By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.
The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, VFs in SRIOV VFs are denied QP0 access. The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology. Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.
However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.
This commit does the following:
1. Create QP0 tunnel QPs for all VFs.
2. Discard SMI mads sent-from/received-for non-privileged VFs in the
hypervisor MAD multiplex/demultiplex logic. SMI mads from/for
privileged VFs are allowed to pass.
3. MAD_IFC wrapper changes/fixes. For non-privileged VFs, only
host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
GET mads. For privileged VFs, there are no restrictions.
This commit does not allow privileged VFs as yet. To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled(). This function
returns 0 unconditionally for now.
The next two commits allow defining and activating privileged VFs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit eb17711bc1 ("net/mlx4_core: Introduce nic_info new flag in
QUERY_FUNC_CAP") did:
if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_OFFSET) {
which should be:
if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_FORCE_VLAN) {
Fix that.
Fixes: eb17711bc1 ("net/mlx4_core: Introduce nic_info new flag in QUERY_FUNC_CAP")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix a few memory leaks that happen if errors happen in SR-IOV mode.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add a function to walk the list of subnodes of a mdio bus and look for
a node that matches the phy's address with its 'reg' property. If found,
set the of_node pointer for the phy. This allows auto-probed pyh
devices to be augmented by information passed in via DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the config option is gone, the driver needs to be converted
over to using the dynamic_debug infrastructure, like all other USB
drivers have been already.
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
A check for CONFIG_AUTOSUSPEND was included in this driver when it was
added in v2.6.39. But that Kconfig symbol doesn't exist. Remove that
check and the single line it hides.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 does not support WDS and DFS with channel context
drivers. So advertise these features only when the driver is not
supporting channel context and modparam "use_chanctx" is introduced
for preparing channel context support in ath9k.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If host sleep parameter gap is set to 0xff, firmware will wait
for an ack from host to confirm the success of host wakeup.
This prevents firmware from uploading data packet before host
actually wakes up.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current implementation sets tdls_link flag only while restoring
packets from TDLS queue. If traffic to peer starts after TDLS is
setup, there is no way to set TDLS link flag to true. Do this
while creating RA list and we confirm that there exist a TDLS
peer for which setup is complete.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[113.967694] Unable to handle kernel NULL pointer dereference
at virtual address 00000020
............
[113.967859] PC is at mwifiex_update_rxreor_flags+0xfc/0x430
............
[113.968110] mwifiex_update_rxreor_flags+0xfc/0x430
[113.968129] mwifiex_handle_event_ext_scan_report+0x1e4/0x21c
[113.968148] mwifiex_process_sta_event+0x410/0x508
[113.968165] mwifiex_process_event+0x184/0x1e0
[113.968181] mwifiex_main_process+0x220/0x48c
[113.968197] mwifiex_sdio_interrupt+0xc8/0x1cc
[113.968210] sdio_irq_thread+0x11c/0x290
In case of legacy scan, adapter->curr_cmd is guranteed to be
non-NULL in check_next_scan_cmd. This may not be case in
extended scan where scan command response would come earlier and
set curr_cmd to NULL. Extended scan event comes later and while
trying to complete IOCTL for scan, driver would crash in
dereferencing adapter->curr_cmd->wait_q_enabled.
Avoid this by completing IOCTL in case of legacy scans only.
Internal scan would be completed while handling extended scan
command response.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Broadcom's wl 6.30.223.141 has some optimizations for radios 0x205[67].
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY has to be often re-initialized (e.g. during band switching after PHY
reset), however some operations have to be performed only once (only
power reset affects them).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of receiving frame with sequence number far greater than current,
wil_release_reorder_frames() will iterate many times over empty buffer.
Optimize this case by checking buffer emptiness and simply update
head_seq_num without iterating.
Suggested-by: Vladimir Shulman <Vladimir.Shulman@Wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use proper format %pad for the dma_addr_t arguments;
prefix %p with 0x, as %p don't print is by itself
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan has not finished in some reasonable time (10sec), interpret it as
if firmware error occurs but was not reported. Firmware should report
scan completion for every scan request, so it is error condition indeed.
Perform firmware recovery procedure.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide clear definition of the watermarks for the vring descriptor space.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case there is something fundamentally wrong with the firmware
(example: RF cable disconnected), FW will always crash immediately
after reset. This leads to infinite fw error recovery loop.
Count consecutive unsuccessful error recovery attempts in a short period
of time, and stop doing recovery after some reasonable count.
It is still possible to manually reset fw doing
interface down/up sequence.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obey 802.11 spec that defines max. data size 7920 bytes
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pm_lock is taken twice while syncing HW TSF of p2p vif.
Fix this by taking the lock at caller side.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB driver was using a list for firmware info that was
used in suspend/resume scenario. Now that brcmfmac is using
the asynchronous firmware request this is no longer needed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB bus driver always configured an USB intr EP urb. The
driver did not use the result at all and with newer firmware it is
causing continues errors on this EP.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max buffer size for receiving control message from dongle needs to be
increased considering possible block padding. Otherwise some big control
message can't be received due to buffer overrun check.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware channel specification is a bitfield using a
16-bit integer, but only 14 lsb are used. Upon encoding
this value assure all 16 bits are cleared.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_fw_nvram_strip() is no longer called so
it does not need to be exposed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds use of asynchronous firmware request to
the driver USB layer.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds use of asynchronous firmware request to
the driver SDIO layer.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver needs firmware to be loaded to the device, which
is done through the firmware class API. The synchronous call
request_firmware() need root filesystem to be mounted and/or
user-mode helper. These may not be avaliable on the moment
it is called. Instead use request_firmware_nowait().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The resume callbacks do partly the same a the probe callback
so put common code in separate function for use in the callbacks.
This also fixes suspend/resume regression introduced by
brcmfmac: remove .init() callback for internal bus interface
The .init() callback was the first function called by the common
bus function brcmf_bus_start(). Given that it is not really
necessary and the bus layer can call it before calling the
brcmf_bus_start() function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_detach() checks whether it needs to do his stuff
or can return immediately. No need to have the same check in the
calling code.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware processing will be modified to use asynchronous request
firmware api. In preparation this patch is simple rename of source
and header file to which the functionality will be added.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The .init() callback was the first function called by the common
bus function brcmf_bus_start(). Given that it is not really
necessary and the bus layer can call it before calling the
brcmf_bus_start() function.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function chandef_to_chanspec() was added by
brcmfmac: determine chanspec from struct cfg80211_chan_def info
The struct cfg80211_chan_def contains additional info to derive the
bandwidth and side-band information of the chanspec. This patch adds
chandef_to_chanspec() function used in IBSS join and starting AP
operation.
However, it introduced a sparse warning because the function
is only called from within the source file wl_cfg80211.c.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before informing cfg80211 about the scan status the device should
be put back in mpc state. If done after user-space may initiate
another (scheduled) scan and fail because scan is still busy as
shown in logging below:
[ 3301.367376] brcmfmac: brcmf_fweh_event_worker event ESCAN_RESULT (69)
[ 3301.377305] brcmfmac: brcmf_fweh_event_worker version 2 flags 0 status 0
[ 3301.384993] brcmutil: event payload, len=12
[ 3301.389208] 00000000: 0c 00 00 00 6d 00 00 00 34 12 00 00
[ 3301.389214] brcmfmac: brcmf_sdio_kso_control Enter: on=0
[ 3301.402196] brcmfmac: brcmf_inform_bss scanned AP count (0)
[ 3301.407808] brcmfmac: brcmf_notify_escan_complete Enter
[ 3301.413064] brcmfmac: brcmf_notify_escan_complete ESCAN Completed scan: Done
[ 3301.420137] brcmfmac: brcmf_sdio_bus_txctl Enter
[ 3301.420368] brcmfmac: brcmf_cfg80211_sched_scan_start Enter
[ 3301.420370] brcmfmac: brcmf_cfg80211_sched_scan_start:
Scanning already: status (1)
[ 3301.440190] brcmfmac: brcmf_sdio_kso_control Enter: on=1
[ 3301.448695] brcmfmac: brcmf_sdio_tx_ctrlframe Enter
[ 3301.453662] brcmfmac: brcmf_sdio_bus_rxctl Enter
[ 3301.458326] brcmfmac: brcmf_sdio_isr Enter
[ 3301.462523] brcmfmac: brcmf_sdio_dpc Enter
[ 3301.466632] brcmfmac: brcmf_sdio_readframes Enter
[ 3301.471431] brcmfmac: brcmf_sdio_read_control Enter
[ 3301.476340] brcmfmac: brcmf_set_mpc MPC : 1
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a regular scan does not return any networks user-space does
request a scheduled scan without any matchset or ssid. This can
not be handled by the firmware so we return -EINVAL. However, as
this request is done let us not add an error message to the log.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Rose