pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.
Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timeout to prevent infinite loop waiting for PHY to reset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess printks when the link is down.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ethtool support to tlan driver:
- driver info - link detect (this allows NetworkManager to detect carrier)
- EEPROM read
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable old link monitoring code and modify it:
- control LINK LED
- use separate timer so it does not interfere with ACT LED
Tested with Olicom OC-2326.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 ethernet cards have an activity LED but it does not
work with tlan driver as it's not enabled. Enable it.
Tested with OC-2326.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding vlans, when the HW limit of vlan filters is reached, the
driver enables vlan promiscuous mode.
Similarily, while removing vlans, the driver must re-enable HW filtering
as soon as the number of vlan filters is within the HW limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SR-IOV is enabled in the adapter, the FW distributes queue resources
evenly across the PF and it's VFs. If the user is not interested in enabling
VFs, the queues set aside for VFs are wasted.
This patch adds support for the PF driver to re-configure the resource
distribution in FW based on the number of VFs enabled by the user.
This also allows for supporting RSS queues on VFs, when less number of VFs
are enabled per PF. When maximum number of VFs are enabled, each VF typically
gets only one RXQ.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver must query the FW for VF's interface capabilities
to know if the VF is RSS capable or not.
This patch is in preparation for enabling RSS on VFs on Skyhawk-R.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix be_cmd_get_profile_cmd() to use be_cmd_notify_wait() routine,
which uses MBOX if MCCQ has not been created. Doing this reduces
code duplication; we don't need the _mbox/_mccq() variants anymore.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since consume_skb() (and hence dev_kfree_skb() macro) checks the passed pointer
for NULL, there's no need to check for NULL before invoking dev_kfree_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Collect a firmware dump on first Tx timeout if netif_msg_tx_err() is set
- Log Receive and Status ring info on Tx timeout, in addition to Tx ring info
- Log additional Tx ring info if netif_msg_tx_err() is set
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-01
This series contains updates to i40e, i40evf, igb and ixgbe.
Shannon adds the Base Address High and Low to the admin queue structure
to simplify the logic in the configuration routines. Also adds code to
clear all queues and interrupts to help clean up after a PXE or other
early boot activity.
Kevin fixes mask assignment value since -1 cannot be used for unsigned
integer types.
Mitch fixes an issue where in some circumstances the reply from the PF
would come back before we were able to properly modify the admin queue
pending and required flags. This would mess up the flags and put the
driver in an indeterminate state, so fix this by simply setting the flags
before sending the request to the admin queue. Also changes the branding
string for i40evf to reduce confusion and to match up with our other
marketing materials.
Kamil adds a new variable defining admin send queue (ASQ) command write
back timeout to allow for dynamic modification of this timeout.
Anjali fix a bug in the flow director filter replay logic, so that we
call a replay after a sideband reset correctly.
Jesse adds code to initialize all members of the context descriptor to
prevent possible stale data.
Christopher fixes i40e to prevent writing to reserved bits, since the
queue index is only 0-127.
Jacob removes the unneeded header export.h from the i40e PTP code.
Fixes ixgbe PTP code where the PPS signal was not correct, as it
generates a one half HZ clock signal, it only generates one level
change per second. To generate a full clock, we need two level changes
per second.
Todd provides a fix for igb to bring up link when the PHY has powered
up, which was reported by Jeff Westfahl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This limitation maybe had some reason in the past, but now there is not
one -> removing this.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rip out a bunch of redundant PCI-E Memory Window Read/Write routines,
collapse the more general purpose routines into a single routine
thereby eliminating the need for a large stack frame (and extra data
copying) in the outer routine, change everything to use the improved
routine t4_memory_rw.
Based on origninal work by Casey Leedom <leedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the firmware interface to get the BAR0 value since we really don't want
to use the PCI-E Configuration Space Backdoor access which is owned by the
firmware.
Set up PCI-E Memory Window registers using the true values programmed into
BAR registers. When the PF4 "Master Function" is exported to a Virtual
Machine, the values returned by pci_resource_start() will be for the
synthetic PCI-E Configuration Space and not the real addresses. But we need
to program the PCI-E Memory Window address decoders with the real addresses
that we're going to be using in order to have accesses through the Memory
Windows work.
Based on origninal work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change logic which determines our Physical Function at PCI Probe time.
Now we read the PL_WHOAMI register and get the Physical Function.
Pass Physical Function to Upper Layer Drivers in lld_info structure in the
new field "pf" added to lld_info. This is useful for the cases where the
PF, say PF4, is attached to a Virtual Machine via some form of "PCI
Pass Through" technology and the PCI Function shows up as PF0 in the VM.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Periodic output triggers 0 and 1 of the dp83640 has a programmable
duty-cycle which is controlled by the Pulsewidth2 field of the trigger
data register. This field is not documented in the datasheet, but it
is described in the "PHYTER Software Development Guide" section
3.1.4.1. Failing to set the field can result in unstable/no trigger
output.
Add programming of the Pulsewidth2 field, setting it to the same value
as the Pulsewidth field for a 50% duty cycle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are linux distributions where the inbox bnx2x driver contains SRIOV
support but doesn't contain the changes introduced in b9871bcf
"bnx2x: VF RSS support - PF side".
A VF in a VM running that distribution over a new hypervisor will access
incorrect addresses when trying to transmit packets, causing an attention
in the hypervisor and making that VF inactive until FLRed.
The driver in the VM has to ne upgraded [no real way to overcome this], but
due to the HW attention currently arising upgrading the driver in the VM
would not suffice [since the VF needs also be FLRed if the previous driver
was already loaded].
This patch causes the PF to fail the acquire message from a VF running an
old problematic driver; The VF will then gracefully fail it's probe preventing
the HW attention [and allow clean upgrade of driver in VM].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves the performance of driver on machine with L1_CACHE_SHIFT of at
most 32 bytes [HW was planned for 64-byte aligned fastpath data].
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now VFs were oblvious to the actual configured link parameters.
This patch does 2 things:
1. It enables a PF to inform its VF using the bulletin board of the link
configured, and allows the VF to present that information.
2. It adds support of `ndo_set_vf_link_state', allowing the hypervisor
to set the VF link state.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPS signal is not correct, as it generates a one half HZ clock
signal, as it only generates one level change per second. To generate a
full clock, we need two level changes per second. Also, change the name
of the #define, in order to prevent confusion between it and
NSEC_PER_SEC which is not guaranteed to be a 64bit value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call igb_setup_link() when the PHY is powered up.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a slash to the branding string to reduce confusion and match up with
our other marketing materials.
Change-ID: I8229e8c3e43083b7a29c859a250f8d2d4dc46b9e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need the export.h header so we can just go ahead and remove it.
Change-ID: I9057396b141ee449d8299409081358b9270a7c4d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writing to reserved bits, queue index is 0-127
Change-ID: Ic923e1c92012a265983414acd8f547c4bdac2e34
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to initialize all members of context descriptor. Stale
data is possible otherwise.
Change-ID: Idc6b53af45583509da42d5ec0824cbaf78aee64f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the auto_disable flags added there was a bug that was causing the
replay logic to not work correctly.
This patch fixes the issue so that we call a replay after a sideband
reset correctly.
Change-ID: I005fe1ac361188ee5b19517a83c922038cba1b00
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new variable defining ASQ command write back timeout to allow for
dynamic modification of this timeout. Initialize it on AQ initialize
routine with default value, vary it on device ID.
Change-ID: I5c9908f9d7c5455634353b694a986d6f146d1b9d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, the firmware could beat us to the punch, and the
reply from the PF would come back before we were able to properly modify
the aq_pending and aq_required flags. This would mess up the flags and
put the driver in an indeterminate state, much like Schrödinger's cat.
However, unlike the cat, the driver is definitely dead.
To fix this, simply set the flags before sending the request to the AQ.
This way, it won't matter if the interrupt comes back too soon.
Change-ID: I9784655e475675ebcb3140cc7f36f4a96aaadce5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make mask value of all 1s. Value of -1 can't be used for u32 type.
Change-ID: I49d58b77639939fe7447a229dbf1f4a1bf7419ce
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per a recent HW designer comment, this code is for ripping through the
queues and interrupts to fully disable them on driver init, specifically
to help clean up after a PXE or other early boot activity.
Change-ID: I32ed452021a1c2b06dace1969976f882a37b9741
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the AQ BAH and BAL registers on a clean shutdown to help make sure
all is tidy when the driver is done.
Change-ID: I393e92680247daa52a8e00bab183213672d73578
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Base Address High and Low to the admin queue struct to simplify
another bit of "which context" logic in the config routines.
Change-ID: Iae195a7da3baffc1a9d522119e1e2b427068ad07
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-26
This series contains updates to i40e and i40evf.
Kamil provides a cleanup patch to i40e where we do not need to acquire the
NVM for shadow RAM checksum calculation, since we only read the shadow RAM
through SRCTL register.
Paul provides a fix for handling HMC for big endian architectures for i40e
and i40evf.
Mitch provides four cleanup and fixes for i40evf. Fix an issue where if
the VF driver fails to complete early init, then rmmod can cause a softlock
when the driver tries to stop a watchdog timer that never got initialized.
So add a check to see if the timer is actually initialized before stopping
it. Make the function i40evf_send_api_ver() return more useful information,
instead of just returning -EIO by propagating firmware errors back to the
caller and log a message if the PF sends an invalid reply. Fix up a log
message that was missing a word, which makes the log message more readable.
Fix an initialization failure if many VFs are instantiated at the same time
and the VF module is autoloaded by simply resending firmware request if
there is no response the first time.
Jacob does a rename of the function i40e_ptp_enable() to
i40e_ptp_feature_enable(), like he did for ixgbe, to reduce possible
confusion and ambugity in the purpose of the function. Does follow on
PTP work on i40e, like he did for ixgbe, by breaking the PTP hardware
control from the ioctl command for timestamping mode. By doing this,
we can maintain state about the 1588 timestamping mode and properly
re-enable to the last known mode during a re-initialization of 1588 bits.
Anjali cleans up the i40e driver where TCP-IPv4 filters were being added
twice, which seems to be left over from when we had to add two PTYPEs for
one filter. Fixes the flow director sideband logic to detect when there
is a full flow director table. Also fixes the programming of FDIR where
a couple of fields in the descriptor setup that were not being
programmed, which left the opportunity for stale data to be pushed as
part of the descriptor next time it was used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch issued a warning preferring to use kstrto<type> when
using a single variable sscanf. Change the sscanf invocation to
a kstrtouint call.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary