The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.
The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.
A subsequent probing of the clock fails due to the invalid value range in
the register, though.
[ And if it didn't, reading the clock would yield a bogus year because
the function translating registers to tm_year is assuming a register
value of 19 or 20. ]
This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.
Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Remove wrong and unnecessary unmask operation
- Remove extra GEDR reading
This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following issues have been addressed on DA8XX/OMAP-L1XX:
a. Screen misalignment during booting when frame buffer console is
enabled.
b. Driver was configured always in PSEUDOCOLOR mode. This patch
dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
mode depending on bpp.
c. The RED and BLUE offsets were interchanged resulting in wrong
bootup logo colour.
This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"rtc" is freed and then dereferenced on the next line. This patch fixes
that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
USB: work around for EHCI with quirky periodic schedules
USB: musb: Fix CPPI IRQs not being signaled
USB: musb: respect usb_request->zero in control requests
USB: musb: fix ISOC Tx programming for CPPI DMAs
USB: musb: Remove unwanted message in boot log
usb: amd5536udc: fixed shared interrupt bug and warning oops
USB: ftdi_sio: Keep going when write errors are encountered.
USB: musb_gadget: fix STALL handling
USB: EHCI: don't send Clear-TT-Buffer following a STALL
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/of_serial: add missing ns16550a id
bcm63xx_uart: Fix serial driver compile breakage.
tty_port: handle the nonblocking open of a dead port corner case
There was confusion between the array size and the highest ISEL
value possible.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
commit 4706b349f was a forward port of a fix that was needed
for SLES10. But in fact it is not needed in mainline because
the earlier commit dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction. If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.
After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some missing author names.
They were accidentally removed by someone within Microsoft before the
files were sent for inclusion in the kernel.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication. Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nearly every invocation of memset in drivers/staging/hv/StorVsc.c has
its arguments the wrong way around.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some drivers allow O_NDELAY of a dead port (eg for setserial to work). In that
situation we must not try to raise the carrier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: gcm - fix another complete call in complete fuction
crypto: padlock-aes - Use the correct mask when checking whether copying is required
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
at24: Use timeout also for read
i2c: Fix userspace_device list corruption
MAINTAINERS: Add missing i2c files
i2c/tsl2550: Fix lux value in extended mode
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Update mach-types
ARM: 5793/1: ARM: Check put_user fail in do_signal when enable OABI_COMPAT
MAINTAINERS: add maintainer information for AMBA primecell drivers
[ARM] pxa/spitz: fix compile regression on spitz
ARM: PNX4008: i2c-pnx: use the same dev_id for request_irq and free_irq
[ARM] pxa/cpufreq: fix index assignments for end marker
ARM: PNX4008: fix watchdog device driver name
[ARM] kmap: fix build errors with DEBUG_HIGHMEM enabled
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sunsu: Use sunserial_console_termios() in sunsu_console_setup().
sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
sunsu: Fix detection of SU ports which are RSC console or control.
sunsab: Do not set sunsab_reg.cons right before registering minors.
sparc64: Fix definition of VMEMMAP_SIZE.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
b44: Fix wedge when using netconsole.
wan: cosa: drop chan->wsem on error path
ep93xx-eth: check for zero MAC address on probe, not on device open
NET: smc91x: Fix irq flags
smsc9420: prevent BUG() if ethtool is called with interface down
r8169: restore mac addr in rtl8169_remove_one and rtl_shutdown
ipv4: additional update of dev_net(dev) to struct *net in ip_fragment.c, NULL ptr OOPS
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failure
sctp: on T3_RTX retransmit all the in-flight chunks
pktgen: Fix netdevice unregister
macvlan: fix gso_max_size setting
rfkill: fix miscdev ops
ath9k: set ps_default as false
hso: fix soft-lockup
hso: fix debug routines
pktgen: Fix device name compares
stmmac: do not fail when the timer cannot be used.
stmmac: fixed a compilation error when use the external timer
netfilter: xt_limit: fix invalid return code in limit_mt_check()
Au1x00: fix crash when trying register_netdev()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: pass correct iso xmit timestamps to core
firewire: ohci: Make cycleMatch ISO transmission work
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: make device attrs static
Thaw refrigerated bdi flusher threads before invoking kthread_stop on them
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acerhdf: return temperature in milidegree instead of degree
thinkpad-acpi: fix detection of old ThinkPads
thinkpad-acpi: fix sign of ERESTARTSYS return
ACPI: Add Thinkpad T400, T500 to OSI(Linux) white-list
ACPICA: Silence the warning about _BIF returning the buffer
ACPI: DMI init_set_sci_en_on_resume for HP-Compaq C700
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/fb: fix FBIOGET/PUT_VSCREENINFO pixel clock handling
drm: make sure page protections are updated after changing vm_flags
drm/radeon/kms: Report vga connector is connected according to ddc_probe
drm: mm always protect change to unused_nodes with unused_lock spinlock
drm/radeon/kms: Disable TV load detect on RS400,RC410,RS480
drm/radeon/kms: read back register before writing in IIO.
drm/radeon/kms: fix handling of d1/d2 vga
drm: work around EDIDs with bad htotal/vtotal values
drm/radeon/kms: resume AGP by calling init.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Staging: octeon-ethernet: Assign proper MAC addresses.
Staging: Octeon: Use symbolic values for irq numbers.
MIPS: Octeon: Fix compile error in drivers/staging/octeon/ethernet-mdio.c
Fix mutex function usage, which was overlooked in a previous patch.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by Stefan Lippers-Hollmann <s.L-H@gmx.de>,
Commit: fd9a40da1d broke s2250
compilation.
This patch re-adds the missing s2250-loader.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was
commit d75636ef9c
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:25:53 2009 +0100
mac80211: RX aggregation: clean up stop session
and other parts were already present in the original
commit d92684e660
Author: Ron Rindjunsky <ron.rindjunsky@intel.com>
Date: Mon Jan 28 14:07:22 2008 +0200
mac80211: A-MPDU Tx add delBA from recipient support
The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.
The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.
For this case, there are two things necessary to fix it:
1) don't process spurious delBA frames, and be more careful
about the session state; don't drop the lock
2) HT drivers need to be prepared to handle a session stop
even before the session was really started -- this is
true for all drivers (that support aggregation) but
iwlwifi which can be fixed easily. The other HT drivers
(ath9k and ar9170) are behaving properly already.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes kernel bugzilla #14691
Due to the way netpoll works, it is perfectly legal to see
NAPI already scheduled when new device events are pending
in b44_interrupt().
So logging a message about it is wrong and in fact harmful.
Based upon a patch by Andreas Mohr.
Signed-off-by: David S. Miller <davem@davemloft.net>
The other paths all drop chan->wsem. This was found by a static
checker (smatch).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we happen to have registered the driver without passing
a MAC address, we will print a zero MAC address and register
the interface with this invalid address, this is confusin. This
patch moves the checking of a valid ethernet address and the
generation of a random one down from the open function to
the probe function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91x.h defines SMC_IRQ_FLAGS to be -1 when it wants the interrupt
flags to be taken from the resource structure. However, d280ead
changed this to checking for non-zero resource flags.
Unfortunately, this means that on some platforms, we end up passing
'-1' to request_irq rather than the desired result. Combine the two
conditions into one so that the IRQ flags are taken from the resource
if either SMC_IRQ_FLAGS is -1 or the resource flags specify an
interrupt trigger.
This restores network on at least the Versatile platform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a null pointer dereference BUG() if ethtool is used on
an smsc9420 interface while it is down, because the phy_dev is only
allocated while the interface is up.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer chipsets (all PCI-E) are known that they need full power cycle
(AC or battery removal) to reset MAC address to a hardwired one. Previous
patch to address this problem loads the original MAC address from EEPROM.
But it brought other problem for which it is necessary to introduce a new
module parameter.
However, it might suffice to restore the initial MAC address before
shutdown/reboot/kexec and when removing the module.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems
with limited memory (Bug #14265). pci_pool_alloc allows waiting with
GFP_KERNEL.
Tested-by: Karol Lewandowski <karol.k.lewandowski@gmail.com>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1305) fixes a bug in the irq-enable settings and removes
some related overhead in the runtime PM code.
In __pm_runtime_resume(), within the scope of the original
spin_lock_irq(), we know that irqs are disabled. There's no
reason to go through a pair of enable/disable cycles when
acquiring and releasing the parent's lock.
In __pm_runtime_set_status(), irqs are already disabled when
the parent's lock is acquired, and they must remain disabled
when it is released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_request_window() only needs a pointer to struct pcmcia_device, not
a pointer to a pointer.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
Acked-by: Karsten Keil <keil@b1-systems.de> (for ISDN)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_get_window() and pcmcia_get_mem_page() were only called from
pcmcia_ioctl.c. Therefore, move these functions to that file, and
remove the useless EXPORTs.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Logic changes based on top of the other patches:
This set of patches changed window_handle_t from being a pointer to an
unsigned long. The unsigned long is now a simple index into socket->win[].
Going from a pointer to unsigned long should leave the user space interface
unchanged unless I'm mistaken.
This change results in code that is less error prone and a user space
interface which is much cleaner and safer. A nice side effect is that we
are also are able to remove all members except one from window_t.
[ linux@dominikbrodowski.net:
Update to 2.6.31. Also, a plain "index" to socket->win[] does not
work, as several codepaths rely on "window_handle_t" being
non-zero if used. Therefore, set the window_handle_t to the
socket->win[] index + 1. ]
CC: netdev@vger.kernel.org
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
No logic changes, just pass struct pcmcia_socket to pcmcia_get_mem_page()
[linux@dominikbrodowski.net: update to 2.6.31]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Edwin Török found the following:
In function ‘memset’,
inlined from ‘ir_input_init’ at drivers/media/common/ir-functions.c:67:
/home/edwin/builds/linux-2.6/arch/x86/include/asm/string_64.h:61:
warning: call to ‘__warn_memset_zero_len’ declared with attribute
warning: memset used with constant zero length parameter; this could be
due to transposed parameters
memset(ir->ir_codes, sizeof(ir->ir_codes), 0);
In actual practice the only caller I can find happens to already have cleared
the buffer before calling ir_input_init.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial fix for this compile warning:
v4l/sh_mobile_ceu_camera.c:1789: warning: label 'exit_free_irq' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Address yet another regression introduced by the introduction of the zl10353
disable_i2c_gate field.
djh - I unmangled the patch which apparently got screwed up in the user's
email client.
Signed-off-by: Robert Lowery <rglowery@exemail.com.au>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When building for Sun 3:
drivers/built-in.o: In function `smscore_unregister_device':
drivers/media/dvb/siano/smscoreapi.c:723: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `smscore_register_device':
drivers/media/dvb/siano/smscoreapi.c:365: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vpif_config struct was renamed to vpif_display_config, but there
is still a stray vpif_config *config pointer in vpif_display.c, preventing
it from compiling.
Remove this old duplicate pointer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set device GPIOs only once. There is no need for .dvb_gpio to select
between analog and digital because device is digital only.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit ef373189f62413803b7b816c972fc154c488cdc0 "fix use-after-free Oops,
resulting from a driver-core API change" fixed the Oops, but didn't correct
missing device object initialisation. This patch makes unloading and reloading
of soc-camera host- and client-drivers possible again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Double mutexlock found by the Linux Driver Verification project and
reported by Alexander Strakh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__scsi_remove_device() in scsi_forget_host() is executed out of scan_mutex
and races with scsi_destroy_sdev() <- scsi_sysfs_add_devices() <-
scsi_finish_async_scan(). The result is use after free and/or double
free, oops.
The fix is simple, move scsi_forget_host() under scan_mutex.
scsi_forget_host() is just sequence of __scsi_remove_device(). All
another calls of __scsi_remove_device() are made under scan_mutex. So
that it is safe.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Async scanning introduced a very wide window where the SCSI device is
up and running but has not yet been added to sysfs. We delay the
adding until all scans have completed to retain the same ordering as
sync scanning.
This delay in visibility causes an oops if a device is removed before
we make it visible because the SCSI removal routines have an inbuilt
assumption that if a device is in SDEV_RUNNING state, it must be
visible (which is not necessarily true in the async scanning case).
Fix this by introducing an additional is_visible flag which we can use
to condition the tear down so we do the right thing for running but
not yet made visible.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd_dif.c was not updated to return -EILSEQ, leading to error handling
failures in applications which provide their own integrity metadata (as
opposed to being protected by the block layer functions).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Writes may take some time on EEPROMs, so for consecutive writes, we already
have a loop waiting for the EEPROM to become ready. Use such a loop for reads,
too, in case somebody wants to immediately read after a write. Detailed bug
report and test case can be found here:
http://article.gmane.org/gmane.linux.drivers.i2c/4660
Reported-by: Aleksandar Ivanov <ivanov.aleks@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Aleksandar Ivanov <ivanov.aleks@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
According to the TAOS Application Note 'Controlling a Backlight with
the TSL2550 Ambient Light Sensor' (page 14), the actual lux value in
extended mode should be obtained multiplying the calculated lux value
by 5.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Keysyms stored in key_map[] are not simply K() values, but U(K()) values,
as can be seen in the KDSKBENT ioctl handler. The kernel-generated
braille keysyms thus need a U() call too.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, ide_cmd_ioctl when invoked for setting DMA transfer mode calls
ide_find_dma_mode with requested mode as XFER_UDMA_6. This prevents setting DMA
mode to any other value than the default (maximum) supported by the device (or
UDMA6, if supported) irrespective of the actual requested transfer mode and
returns error.
For example, setting mode to UDMA2 using hdparm, where UDMA4 is the default
transfer mode gives following error:
# ./hdparm -d1 -Xudma2 /dev/hda
/dev/hda:hda: UDMA/66 mode selected
setting using_dma to 1 (on)
hda: UDMA/66 mode selected
setting xfermode to 66 (UltraDMA mode2)
HDIO_DRIVE_CMD(setxfermode) failed: Invalid argument
using_dma = 1 (on)
This patch fixes the issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver requires shmfs as the backing filesystem to handle the buffer
objects, so ensure it is selected if the user chooses to build our
driver.
Fixes: Bug 14662 - Dell E5500 kernel panic with KMS
http://bugzilla.kernel.org/show_bug.cgi?id=14662
The revealing nature of the panic is the NULL function pointer
dereference in read_cache_page_async().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Mateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: stable@kernel.org
For CRT hotplug detect status, we have four test results as blue
channel only, green channel only, both blue and green channel, and
no channel attached. Origin code only marks both blue and green channel
case as connected, but ignore other possible connected states. This one
trys to detect CRT by checking no channel attached case instead.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Return temperature in milidegree instead of degree, as sysfs-api requires
the temperature in milidegree.
Signed-off-by: Peter Feuerer <peter@piie.net>
Tested-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a problem in the quirk tables used by tpacpi_is_fw_known() and
tpacpi_check_outdated_fw(), which causes outdated BIOSes that are lacking
the EC firmware ID DMI field to never match.
This breaks module loading on, e.g. a T23 with outdated BIOS, and the
module will refuse to load unless the "force_load=1" parameter is given.
Fix the quirk tables so that they can also match the outdated BIOSes,
which in turn will both fix the module loading, and also warn the user
that he is using outdated firmware and should upgrade.
This fixes a serious regression, introduced by commit
e675abafcc, "thinkpad-acpi: be more strict
when detecting a ThinkPad".
http://bugzilla.kernel.org/show_bug.cgi?id=14597
Reported-by: Paul Kimoto <kimoto@lightlink.com>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Tested-by: Paul Kimoto <kimoto@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The returned error should be negative
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_osi=Linux helps the mute button work properly by sending Linux
a mute key press.
http://bugzilla.kernel.org/show_bug.cgi?id=13934
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_BIF was returning buffer instead of a string since day 1 of ACPI.
Adding a warning for that is noble, but people don't like
when someone cries wolf in a production system.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=14379
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Be like the other Sun serial drivers otherwise the special handling of
OpenFirmware options and hard-coded overrides for LOM/RSC consoles
will not be handled.
Signed-off-by: David S. Miller <davem@davemloft.net>
RSC and LOM devices have fixed speed settings.
We already had some code to match and handle "rsc" named devices on
E250 systems, but we also have to handle 'rsc-console', 'rsc-control',
and 'lom-console'.
Also, in order to get this right regardless of what 'output-device'
happens to be, explicitly pass the UART device node pointer to this
routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
This tells the logic to ignore the line match when deciding whether the
device is the OpenFirmware specified console device or not.
This is going to be used in the SU driver for rsc-console detection.
There is probably a better way to handle this, but this is the least
intrusive solution for now which we can validate won't break any other
cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
These device nodes are named "rsc-console" and "rsc-control" rather
than 'serial', but the device_type property is 'serial' so we'll
tip off of that for detection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Other Sun serial drivers do not do this, and if we keep it this way
it ends up registering all serial devices as consoles rather than
just the one which we explicitly register via sunserial_console_match()
which uses add_preferred_console().
Signed-off-by: David S. Miller <davem@davemloft.net>
When the framebuffer driver does not publish detailed timing information
for the current video mode, the correct value for the pixclock field is
zero, not -1.
Since pixclock is actually unsigned, the value -1 would be interpreted
as 4294967295 picoseconds (i.e., about 4 milliseconds) by
register_framebuffer() and userspace programs.
This patch allows X.org's fbdev driver to work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some architectures compute ->vm_page_prot depending on ->vm_flags, so we
need to update the protections after adjusting the flags.
AFAIK this only affects running X under Xen; without this patch you get
lots of coloured blobs on the screen, or maybe a complete lockup. Or
anything really.
But that still depends on lots of out-of-tree stuff, so I don't think
there are any consequences for anyone else. But it is wrong in principle.
Reported-by: Jan Beulich <JBeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On broken EDID we were reporting vga connector to be disconnected
even if ddc probe did found a monitor. This patch report that the
connector is connected on such case. This allow drm to add a fail
safe mode (800x600 at the time of this patch) thus user can boot
and later add a mode which match its monitor capabilities.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
unused_nodes modification needs to be protected by unused_lock spinlock.
Here is an example of an usage where there is no such protection without
this patch.
Process 1: 1-drm_mm_pre_get(this function modify unused_nodes list)
2-spin_lock(spinlock protecting mm struct)
3-drm_mm_put_block(this function might modify unused_nodes
list but doesn't protect modification with unused_lock)
4-spin_unlock(spinlock protecting mm struct)
Process2: 1-drm_mm_pre_get(this function modify unused_nodes list)
At this point Process1 & Process2 might both be doing modification to
unused_nodes list. This patch add unused_lock protection into
drm_mm_put_block to avoid such issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
RS400,RC410,RS480 chipset seems to report a lot of false positive
with load detect on TV output. We haven't yet found a way to make
load detect reliable on those chipset, thus just disable it for TV
output. Would avoid user to experience phantom screen because X
believe there is a monitor connected to the TV output.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes RH bugzilla #527874.
On resume the atom posting wasn't working, however vbe posting was
going fine, after 2 weeks over irc, and 8 hrs with the hardware,
I tracked it down to the memory device table and it access the MC
registers via IIO, it appears the rv515 atom iio table might not
be fully functional, so adding a readback before doing a write
either provides enough delay to make things resume correctly.
Thanks to Peng Huang at Red Hat for coming to Brisbane.
Signed-off-by: Dave Airlie <airlied@redhat.com>
An rv515 laptop I got wouldn't startup with a montior plugged in,
found the proper bug hopefully with us not turning off D2VGA
here when we should.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We did this on the userspace side, but we need a similar fix for the
kernel.
Fixes LP #460664.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
AGP resume was broken since we moved to the new init path,
because we never re-enabled AGP on these systems at resume time.
This patch just calls the AGP resume call which just does the reinit
at resume time like the old path did.
Since AGP is pretty much gpu independant I did it outside
the gpu specific code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
gso_max_size must be set based on the value of the underlying device to
support devices not using the full 64k.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate MAC addresses using the same method as the bootloader. This
avoids changing the MAC between bootloader and kernel operation as
well as avoiding duplicates and use of addresses outside of the
assigned range.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In addition to being magic numbers, the irq number passed to free_irq
is incorrect. We need to use the correct symbolic value instead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix soft-lockup in hso.c which is triggered on SMP machine when
modem is removed while file descriptor(s) under /dev are still open:
old version called kref_put() too early which resulted in destroying
hso_serial and hso_device objects which were still used later on.
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the external timer cannot be used the driver
will continue to work without mitigation.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Lohre reported that the driver crashes when trying
to register_netdev(), he sugessted to move dev->netdev_ops initialization
before calling register_netdev(), it worked for him.
Reported-by: Andreas Lohre <alohre@gmail.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1/ Error handling code following a kzalloc should free the allocated data.
2/ Report an error when no platform data is detected
Both problems fixed by moving the platform data check before the allocation,
and allows a goto to be killed.
Reported-by: Julia Lawall <julia@diku.dk>
Acked-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The result of calling kzalloc is never used or freed.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
o Along with netdev->perm_addr, mac address will be
maintained in device private structure.
o Device limitation: We need to set mac address when ever
interface comes up.
In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address.
But bonding driver set netdev->dev_addr field to its original value,
after enslaving interfaces.
When ever active slave changes, it swap dev_addr of inactive slave with active.
Yet it doesn't notify driver about change in netdev->dev_addr.
As netxen driver need to set mac addr when ever interface comes up,
it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel crashes, if promisc mode set without disabling rx queue.
Before changing mode in NX2031 chip, wait till rx queue drains.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting memory during initialization, skip this memory
block during driver probe.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows i2c-pnx to free its interrupt handler when the module
is removed or if an error occurs; using the same dev_id for both
request_irq and free_irq is desirable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Here is the final set of patches I used to get ffado to work with the
new firewire stack. With these patches, I was able to start ardour
and record from and playback to my PreSonus Inspire1394 from a
(mostly) Fedora 12 system.
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Until now, firewire-ohci exposed only the transmit cycle of the last
transmitted packet at each isochronous transmit complete event. This
made it impossible for FFADO (FireWire audio drivers in userspace) to
synchronize audio-out streams. The fix is to store the timestamp of
each packet in the iso xmit event. As a bonus, the transfer status is
stored too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of Changes:
-Fix to receive multicast packets by setting the corresponding hardware
bit during initialization.
-Fix to re-enable the interface [by interface up command(ifup)] while the
interface is down.
-Fix to be able to down the interface by passing the last parameter
correctly to request_irq().
-Remove to read 4 extra bytes from the receiving queue after reading a
packet, even though it does not cause a predictable issue now.
-Remove occurrences of transmission done interrupt in order to tx
throughput enhancement.
-Enable IP checksum for packet receiving by setting the corresponding
hardware bit during initialization.
-Relocate ks_enable_int()/ks_disable_int() in order not to declare those
functions at the beginning of the file.
-Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in
order to give more meaningful names and relocate them not declaire
those functions at the beginning of the file.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building for Sun 3:
drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround for pre-release versions of 82577 is causing link issues on
some switches. The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page. Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:
drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PNX core code calls the device 'pnx4008-watchdog' not 'watchdog'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
The completion of a pq operation is notified with a null descriptor
appended to the end of the chain. This descriptor needs to be visible
to dma clients otherwise the client is precluded from ensuring all
operations are quiesced before freeing channel resources, i.e. due to
descriptor polling it may get the completion notification ahead of the
interrupt delivered by the null descriptor.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ioat3.2 does not support asynchronous error notifications which makes
the driver experience latencies when non-zero pq validate results are
expected. Provide a mechanism for turning off async_xor_val and
async_syndrome_val via Kconfig. This approach is generally useful for
any driver that specifies ASYNC_TX_DISABLE_CHANNEL_SWITCH and would like
to force the async_tx api to fall back to the synchronous path for
certain operations.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Added missing mach/i2c.h and linux/io.h header file includes
Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Limit minimum jiffie timeout to 2 to prevent early timeout on systems
with low tick rates
Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Error interrupts and error completions may cause channel hangs, so
poll the channel status register after a timeout.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
RAID operations cause a system hang on platforms with DCA
(Direct-Cache-Access) enabled. So turn off RAID capabilities in this
case.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Split sata_fsl_softreset() into hard and soft resets to make
error-handling more efficient & device and PMP detection more
reliable.
Also includes fix for PMP support, driver tested with Sil3726,
Sil4726 & Exar PMP controllers.
[AV: Also fixes resuming from deep sleep on MPC8315 CPUs]
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As this struct is exposed to user space and the API was added for this
release it's a bit of a pain for the C++ world and we still have time to
fix it. Rename the fields before we end up with that pain in an actual
release.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Olivier Goffart
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 86cf898e1d ("intel-iommu: Check for
'DMAR at zero' BIOS error earlier.") was supposed to work by pretending
not to detect an IOMMU if it was actually being reported by the BIOS at
physical address zero.
However, the intel_iommu_init() function is called unconditionally, as
are the corresponding functions for other IOMMU hardware.
So the patch only worked if you have RAM above the 4GiB boundary. It
caused swiotlb to be initialised when no IOMMU was detected during early
boot, and thus the later IOMMU init would refuse to run.
But if you have less RAM than that, swiotlb wouldn't get set up and the
IOMMU _would_ still end up being initialised, even though we never
claimed to detect it.
This patch also sets the dmar_disabled flag when the error is detected
during the initial detection phase -- so that the later call to
intel_iommu_init() will return without doing anything, regardless of
whether swiotlb is used or not.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
veth_get_stats() can be called in parallel on several cpus.
It's better to not reset dev->stats as it could give wrong result on
one cpu. Use temporary variables, then store the final results.
Also, we should loop on every possible cpus, not only online cpus,
or cpu hotplug can suddenly give wrong veth stats.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ieee802154_fake_xmit() should free skbs since it returns NETDEV_TX_OK
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix stale cpufreq_cpu_governor pointer
[CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
[CPUFREQ] speedstep-ich: fix error caused by 394122ab14
[CPUFREQ] Fix use after free on governor restore
[CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
[CPUFREQ] powernow-k8: Fix test in get_transition_latency()
[CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()
We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.
This should probably fix the regression reported as k.o. bug #14627.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
Calling the START_ISO ioctl with a nonnegative cycle paramater has
never worked. Last night I got around to figuring out why. Most of
this patch is a big comment explaining why we enable an interrupt
source then don't actually do anything when we get one. As the
comment says, we should do more, but we don't have a way to tell
userspace what happened. . .
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (edited comment)
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fixup last users of irq_chip->typename
uio: pm_runtime_disable is needed if failed
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: cp210x: Fix carrier handling
tty_port: If we are opened non blocking we still need to raise the carrier
unmap Rx page only when guaranteed that this page won't be
used anymore to allocate rx page chunks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TRT bit shifts were reversed for EMAC4 and non-EMAC4 during the
port from ibm_emac to ibm_newemac. This patch corrects that error.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Feng Kan <fkan@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave,
Attached is an update of my patch against the cpufreq fixes branch.
Before applying the patch I compiled and booted the tree to see if the panic
was still there -- to my surprise it was not. This is because of the conversion
of cpufreq_cpu_governor to a char[].
While the panic is kaput, the problem of stale data continues and my patch is
still valid. It is possible to end up with the wrong governor after hotplug
events because CPUFREQ_DEFAULT_GOVERNOR is statically linked to a default,
while the cpu siblings may have had a different governor assigned by a user.
ie) the patch is still needed in order to keep the governors assigned
properly when hotplugging devices
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
ondemand and conservative governors are messing up time units in the
code path where NO_HZ is not enabled and ignore_nice is set. The walltime
idletime stored is in jiffies and nice time calculation is happening in
microseconds.
The problem was reported and diagnosed by Alexander here.
http://marc.info/?l=linux-kernel&m=125752550404513&w=2
The patch below fixes this thinko.
Reported-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Tested-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Currently on governer backup/restore path we storing governor's pointer.
This is wrong because one may unload governor's module after cpu goes
offline. As result use-after-free will take place on restored cpu.
It is not easy to exploit this bug, but still we have to close this
issue ASAP. Issue was introduced by following commit
084f349394
##TESTCASE##
#!/bin/sh -x
modprobe acpi_cpufreq
# Any non default governor, in may case it is "ondemand"
modprobe cpufreq_ondemand
echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
rmmod acpi_cpufreq
rmmod cpufreq_ondemand
modprobe acpi_cpufreq # << use-after-free here.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The return should be negative on errors
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return a negative error value instead of a positive
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface. The storage area for URB data is divided into
fixed-size blocks. If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary). Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.
Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors. In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible. The capture length should be reduced to the
length of the descriptors, not set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: John Youn <John.Youn@synopsys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
>
> i have the following problem with the cdc-acm - driver:
>
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
>
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
>
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
>
> This problem was introduced with the commit
> 10077d4a66 (before 2.6.31-rc1) and still
> exists in 2.6.31.
>
> I was able the fix this problem with the following patch:
>
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
> struct acm *acm = tty->driver_data;
> tty_port_hangup(&acm->port);
> acm_port_down(acm, 0);
> + acm_tty_unregister(acm);
> }
I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.
This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.
Here is a fix for this.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If acm_rx_tasklet() gets called before tty_port_block_til_ready()
returns, then bulk IN urbs may not be sent. This fixes it.
Signed-off-by: Henry Gebhardt <gebhardt@astro.uni-tuebingen.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=29a68e39d4a broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
The tty_port code inherited a bug common to various drivers it was based
upon. If the tty is opened O_NONBLOCK we do not wait for the carrier to be
raised but we must still raise our modem lines if appropriate.
(There is a second question here about whether we should do so if CLOCAL is
set but that can wait)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bfa: declare MODULE_FIRMWARE
[SCSI] gdth: Prevent negative offsets in ioctl CVE-2009-3080
[SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
[SCSI] Fix incorrect reporting of host protection capabilities
[SCSI] pmcraid: Fix ppc64 driver build for using cpu_to_le32 on U8 data type
[SCSI] ipr: add workaround for MSI interrupts on P7
[SCSI] scsi_transport_fc: Fix WARN message for FC passthru failure paths
[SCSI] bfa: fix test in bfad_os_fc_host_init()
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: ensure mfp is in correct range in mfp_{read,write}
[ARM] pxa/hx4700: fix hx4700 touchscreen pressure values
ARM: 5787/1: U300 COH 901 331 fixes
ARM: Fix warning in sa1100-flash.c
[ARM] Kirkwood: disable propagation of mbus error to the CPU local bus
[ARM] pxa: fix incorrect mfp_to_gpio() conversion
[ARM] pxa/colibri: fix AC97 ifdefs and add missing include
[ARM] pxa: fix missing underscores in mfp-pxa910.h
[ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
dereferencing freed memory regulator_fixed_voltage_remove()
regulator: Fix check of unsigned return value and transmit errors in wm831x_gp_ldo_get_mode()
regulator: Handle missing constraints in _regulator_disable()
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds-gpio: fix possible crash on OF device unbinding
backlight: Fix backlight limiting on spitz/corgi devices
backlight: lcd - Fix wrong sizeof
* 'hostprogs-wmissing-prototypes' of git://git.kernel.org/pub/scm/linux/kernel/git/josh/linux-misc:
Makefile: Add -Wmising-prototypes to HOSTCFLAGS
oss: Mark loadhex static in hex2hex.c
dtc: Mark various internal functions static
dtc: Set "noinput" in the lexer to avoid an unused function
drm: radeon: Mark several functions static in mkregtable
arch/sparc/boot/*.c: Mark various internal functions static
arch/powerpc/boot/addRamDisk.c: Mark several internal functions static
arch/alpha/boot/tools/objstrip.c: Mark "usage" static
Documentation/vm/page-types.c: Declare checked_open static
genksyms: Mark is_reserved_word static
kconfig: Mark various internal functions static
kconfig: Make zconf.y work with current bison
We need to look for the 'shared-pins' property to get
this right.
Based upon a patch by Hermann Lauer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commmit 4b77b0a2ba EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Panasonic CF-72 uses 6-byte protocol and does not need to be tied
to a particular port.
Signed-off-by: Abner Holsinger <9zabner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b7802c5c1e ("Input: psmouse - use boolean type") caused the
synaptics_hardware variable to be completely useless, as it is
constantly set to 'true' throughout the whole psmouse_extensions().
This was caused by the following hunk in the commit in question
- int synaptics_hardware = 0;
+ bool synaptics_hardware = true;
which is wrong and causes driver to issue extra reset when falling
back to bare PS/2 protocol.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will fix some small issues with the COH 901 331 RTC driver:
- Interrupt is disabled after alarm so that we don't fire
multiple interrupts.
- We return 0 from the coh901331_alarm_irq_enable() ridding
a compile warning.
- We alter the name in the U300 device registry to match that
of the driver so they sucessfully resolve.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mtd/maps/sa1100-flash.c: In function 'sa1100_probe_subdev':
drivers/mtd/maps/sa1100-flash.c:214: warning: format '%d' expects type 'int', but argument 3 has type 'uint64_t'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't dereference drvdata after it has been freed.
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Johannes Weiner