Odroid HC1 uses the exynos5422-odroid-core.dtsi file as a base. All
other Exynos5422 Odroids use the "common". The ADC node was defined
only in the latter.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 225da7e65a ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7c ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LDO20 regulator provides power for the MMC card on Odroid U3 boards. That
regulator has been marked as 'boot-on' since the beginning of Odroid X/U3
support, but such flag is not really needed for it. That regulator is
correctly described as supply for eMMC card and controlled by its driver.
Commit 05f224ca66 ("regulator: core: Clean enabling always-on regulators
+ their supplies") changed the way the boot-on regulators are handled and
since then regulators marked as 'boot-on' got increased reference count
and are not turned off for the system suspend time.
The new approach turned out to break suspend/resume support on Odroid U3
with eMMC card, because the card is not properly shutdown due to missing
of power cycle. Fix this by removing excessive 'boot-on' flag and let
MMC driver to control turning power on and off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Bindings of the fixed-regulator, which precedes support for GPIO flags
passed via phandle descriptor, introduced its own method annotating
that the given GPIO line is active low or high - by using
'enable-active-high' property. The driver always ignored flags passed
via GPIO descriptor.
Fix the conflicting GPIO flags to match the status forced by the
'enable-active-high' property to avoid future confusion.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the DTC warning for xti node:
arch/arm/boot/dts/s3c2416-smdk2416.dts:23.12-28.5:
Warning (simple_bus_reg): /clocks/xti: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to Devicetree specification, the unit-address must match the
first address specified in the reg property of the node. Fix the DTC
warning onenand node:
arch/arm/boot/dts/s5pv210.dtsi:81.29-93.5:
Warning (simple_bus_reg): /soc/onenand@b0000000: simple-bus unit address format error, expected "b0600000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
This commit adds DMC (Dynamic Memory Controller) nodes, which are needed
by S5Pv210 cpufreq driver to work.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen, connected to I2C-2
- Broadcom BCM4329 Bluetooth over UART-0
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
THis commit adds memory reservation required by MFC (Multi Format Codec)
to run. On S5PV210 both regions needs to be on separate memory banks.
Size of both regions is taken from vendor Linux kernel sources.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since we have U-Boot (flashed in place of stock kernel), it's not needed
anymore to hardcode bootargs on every Aries-family board.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
[krzk: Squash changes to fascinate4g and galaxys into one commit]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since we have separate compatible for S5Pv210 FIMD, let's use it rather
than using one from Exynos4210.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add node for Exynos Rorator device, so it can be used on all S5Pv210
based devices.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcMV5GAAoJED2LAQed4NsGs9gQAI/oGg8wJgk9a7+dJCX245W5
F4ReftnQd4AFptFCi9geJkr+sfViXNgwPLqlJxiXz8Qe8XP7z3LcArDw3FUzwvGn
bMSBiN9ggwWkOFgF523XesYgUVtcLpkNch/Migzf1Ac0FHk0G9o7gjcdsvAWHkUu
qFwtNcUB6PElRbhsHsh5qCY1/6HaAXgf/7O7wztnaKRe9myN6f2HzT4wANS9HHde
1e1r0LcIQeGWfG+3va3fZl6SDxSI/ybl244OcDmDyYl6RA1skSDlHbIBIFgUPoS0
cLyzoVj+GkfI1fRFEIfou+dj7lpukoAXHsggHo0M+ofqtbMF+VB2T3jvg4txanCP
TXzDc+04QUguK5yVnBfcnyC64Htrhnbq0eGy43kd1VZWAEGApl+680P8CRsWU3ZV
kOiFvZQ6RP/Ssw+a42yU3SHr31WD7feuQqHU65osQt4rdyL5wnrfU1vaUvJSkltF
cyPr9Kz/Ism0kPodhpFkuKxwtlKOw6/uwdCQoQHtxAPkvkcydhYx93x3iE0nxObS
CRMximiRyE12DOcv/3uv69n0JOPn6AsITcMNp8XryASYrR2/52txhGKGhvo3+Zoq
5pwc063JsuxJ/5/dcOw/erQar5d1eBRaBJyEWnXroxUjbsLPAznE+UIN8tmvyVly
SunlxNOXBdYeWN6t6S3H
=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 9c2af1c737 ("kbuild: add .DELETE_ON_ERROR special
target"), the target file is automatically deleted on failure.
The boilerplate code
... || { rm -f $@; false; }
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Pull vfs mount API prep from Al Viro:
"Mount API prereqs.
Mostly that's LSM mount options cleanups. There are several minor
fixes in there, but nothing earth-shattering (leaks on failure exits,
mostly)"
* 'mount.part1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (27 commits)
mount_fs: suppress MAC on MS_SUBMOUNT as well as MS_KERNMOUNT
smack: rewrite smack_sb_eat_lsm_opts()
smack: get rid of match_token()
smack: take the guts of smack_parse_opts_str() into a new helper
LSM: new method: ->sb_add_mnt_opt()
selinux: rewrite selinux_sb_eat_lsm_opts()
selinux: regularize Opt_... names a bit
selinux: switch away from match_token()
selinux: new helper - selinux_add_opt()
LSM: bury struct security_mnt_opts
smack: switch to private smack_mnt_opts
selinux: switch to private struct selinux_mnt_opts
LSM: hide struct security_mnt_opts from any generic code
selinux: kill selinux_sb_get_mnt_opts()
LSM: turn sb_eat_lsm_opts() into a method
nfs_remount(): don't leak, don't ignore LSM options quietly
btrfs: sanitize security_mnt_opts use
selinux; don't open-code a loop in sb_finish_set_opts()
LSM: split ->sb_set_mnt_opts() out of ->sb_kern_mount()
new helper: security_sb_eat_lsm_opts()
...
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
- Florian Fainelli noticed that userspace segfaults caused by the lack
of kernel-userspace helpers was hard to diagnose; we now issue a
warning when userspace tries to use the helpers but the kernel has
them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with DT
systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in 4.20
(which had the effect that data that can be placed into the init
sections was incorrectly always placed in the rodata section.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Yl96
-----END PGP SIGNATURE-----
Merge tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Included in this update:
- Florian Fainelli noticed that userspace segfaults caused by the
lack of kernel-userspace helpers was hard to diagnose; we now issue
a warning when userspace tries to use the helpers but the kernel
has them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with
DT systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in
4.20 (which had the effect that data that can be placed into the
init sections was incorrectly always placed in the rodata section)"
* tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm: (25 commits)
ARM: omap2: remove unnecessary boot_lock
ARM: versatile: rename and comment SMP implementation
ARM: versatile: convert boot_lock to raw
ARM: vexpress/realview: consolidate immitation CPU hotplug
ARM: fix the cockup in the previous patch
ARM: sa1100/cerf: switch to using gpio_led_register_device()
ARM: sa1100/assabet: switch to using gpio leds
ARM: sa1100/assabet: add gpio keys support for right-hand two buttons
ARM: sa1111: remove legacy GPIO interfaces
pcmcia: sa1100*: remove redundant bvd1/bvd2 setting
ARM: pxa/lubbock: switch PCMCIA to MAX1600 library
ARM: pxa/mainstone: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/neponset: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/jornada720: switch PCMCIA to gpiod APIs
pcmcia: add MAX1600 library
ARM: sa1100: explicitly register sa11x0-pcmcia devices
ARM: 8813/1: Make aligned 2-byte getuser()/putuser() atomic on ARMv6+
ARM: 8812/1: Optimise copy_{from/to}_user for !CPU_USE_DOMAINS
ARM: 8811/1: always list both ldrd/strd registers explicitly
ARM: 8808/1: kexec:offline panic_smp_self_stop CPU
...
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Merge in a few missing patches from the pull request (my copy of the
branch was behind the staged version in linux-next).
* next/drivers:
memory: pl353: Add driver for arm pl353 static memory controller
dt-bindings: memory: Add pl353 smc controller devicetree binding information
firmware: qcom: scm: fix compilation error when disabled
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the UniPhier MIO DMAC driver. This is used as the DMA engine
for accelerating the SD/eMMC controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mostly clean ups although whilst Doug's was chasing down a odd
lockdep warning he also did some work to improved debugger resilience
when some CPUs fail to respond to the round up request.
The main changes are:
* Fixing a lockdep warning on architectures that cannot use an NMI for
the round up plus related changes to make CPU round up and all CPU
backtrace more resilient.
* Constify the arch ops tables
* A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope
(and directly related to kgdb). Didn't get comprehensive acks but
all impacted maintainers were Cc:ed in good time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEELzVBU1D3lWq6cKzwfOMlXTn3iKEFAlwonoUbHGRhbmllbC50
aG9tcHNvbkBsaW5hcm8ub3JnAAoJEHzjJV0594ihmooP/1uzSMGQIoQMB8XeU/jT
Da2iILybi6hGp7ILA27d0yN3tsJBxWGWs8wzNdzMo3NQ3J0o4foAUnS/R0Vjkg9w
uphe5EA4HDsIrH05OouNb984BeEgNaC9HSqtyr9fXuh024NboULFKIm7REYm+QHT
C5SrBtmonL1xE7FmAhudLWjl7ZlvxM6DJeoVViH4kKq0raTiILt6VJaGl9JfcAdL
m9GEf9r/nh0sCq3GNgyc0y4BvHed+Kxzy1fsIi3jE6t8elaYYR72gNRQ5LaFxcnQ
F04/UtH75qB4rqYsqqV1q0rFi+tj+p9wYTmxixaGWsVDX4Gb5KXuLWJhaRb5IvwC
bdq/0IAXRr4vUL3y0tFWfCj7pHGaVc/gfXi8aieRXLGAZG+tdfuu99NCiulIZTfc
QqZz12Z+99/qi6dK7dBQtaN8SyPeB1QXKWefeGo2Bt5QqiBmcKHxsQYMUo3nkf3J
UXHpj4LG6Ldsi/w8VZfvXmM0/vbO/jrus9m+X2v+4tJyisjrsyv0FRnREI4avfbC
l09P1ajv7RrAaxtab0smV9krqWZ/mSn0zcgcaD6RdKe0+SwsiP/CEx1z1Wb1MH9c
wjEiClXjdVB39YVT0YVfG2Ho7qH8WRErxVyNb/f4QKHMXL1Mu91hFWhBBpUOGUj2
7Jrq2zK1uWramtt7GBDpHYYH
=Aqlc
-----END PGP SIGNATURE-----
Merge tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Mostly clean ups although while Doug's was chasing down a odd lockdep
warning he also did some work to improved debugger resilience when
some CPUs fail to respond to the round up request.
The main changes are:
- Fixing a lockdep warning on architectures that cannot use an NMI
for the round up plus related changes to make CPU round up and all
CPU backtrace more resilient.
- Constify the arch ops tables
- A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope (and
directly related to kgdb). Didn't get comprehensive acks but all
impacted maintainers were Cc:ed in good time"
* tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kgdb/treewide: constify struct kgdb_arch arch_kgdb_ops
mips/kgdb: prepare arch_kgdb_ops for constness
kdb: use bool for binary state indicators
kdb: Don't back trace on a cpu that didn't round up
kgdb: Don't round up a CPU that failed rounding up before
kgdb: Fix kgdb_roundup_cpus() for arches who used smp_call_function()
kgdb: Remove irq flags from roundup
Most changes here are to enable new drivers and platforms in the various
configs that affect them. Most of these have been covered and described
in the other branches, we mostly keep defconfig separate to avoid
conflicts between SoC/dt/driver updates that they otherwise would be
grouped with.
One thing worth mentioning here is that OMAP changes from using their
own UART driver, to 8250, for the multi_v7_defconfig shared config on
32-bit. This means that the console is now named ttyS* instead of ttyO*.
This change was already done for omap2_defconfig a while back, so most
users of these configs have either already updated, or can easily follow
the same patterns as they did at that time. This makes platform support
slightly easier for distros, since they no longer need to keep track of
a separate console prefix for these platforms.
-----BEGIN PGP SIGNATURE-----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=65qL
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Most changes here are to enable new drivers and platforms in the
various configs that affect them. Most of these have been covered and
described in the other branches, we mostly keep defconfig separate to
avoid conflicts between SoC/dt/driver updates that they otherwise
would be grouped with.
One thing worth mentioning here is that OMAP changes from using their
own UART driver, to 8250, for the multi_v7_defconfig shared config on
32-bit. This means that the console is now named ttyS* instead of
ttyO*. This change was already done for omap2_defconfig a while back,
so most users of these configs have either already updated, or can
easily follow the same patterns as they did at that time. This makes
platform support slightly easier for distros, since they no longer
need to keep track of a separate console prefix for these platforms"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
Revert "arm64: defconfig: Enable FSL_MC_BUS and FSL_MC_DPIO"
arm64: defconfig: Enable FSL_MC_BUS and FSL_MC_DPIO
arm64: defconfig: Replace PINCTRL_MT7622 with PINCTRL_MTK_MOORE
arm64: defconfig: Regenerate for v4.20
ARM: multi_v7_defconfig: Add TOSHIBA TC358764 bridge driver
ARM: multi_v7_defconfig: Add MAX8952 regulator driver
ARM: exynos_defconfig: Add TOSHIBA TC358764 bridge driver
ARM: exynos_defconfig: Add MAX8952 regulator driver
ARM: exynos_defconfig: Add MAX8998 RTC and charger drivers
ARM: imx_v6_v7_defconfig: add imx7ulp support
ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
ARM: multi_v7_defconfig: enable STM32 analog & timer drivers
arm64: defconfig: Enable GCC and PINCTRL for MSM8998
arm64: defconfig: Enable core Qualcomm SDM845 options
ARM: defconfig: Enable the PL111 DRM driver on vexpress
ARM: defconfig: Update the vexpress defconfig
arm64: defconfig: Enable some qcom remoteproc configs
arm64: defconfig: Enable QCS404 configs
ARM: imx_v6_v7_defconfig: Enable USB_ANNOUNCE_NEW_DEVICES
ARM: imx_v6_v7_defconfig: Enable BT_BNEP
...
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64 C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
+ misc cleanups across several platforms
-----BEGIN PGP SIGNATURE-----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=yEX2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----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=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
-----------
- Following pen_release and boot_lock cleanup initiated by
Russell King, .smp_prepare_cpus and .smp_boot_secondary STi callbacks
must be reworked to keep secondary CPU's bringup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QbVn
-----END PGP SIGNATURE-----
Merge tag 'sti-soc-for-v4.21-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/late
Highlights:
-----------
- Following pen_release and boot_lock cleanup initiated by
Russell King, .smp_prepare_cpus and .smp_boot_secondary STi callbacks
must be reworked to keep secondary CPU's bringup.
* tag 'sti-soc-for-v4.21-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: sti: remove pen_release and boot_lock
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
-----BEGIN PGP SIGNATURE-----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=dIrg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge in fixes here, since the last batch didn't make it in before the
release of 4.20, and we might as well group them with this set of
patches.
* fixes: (822 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: realview: Fix some more duplicate regulator nodes
MAINTAINERS: update entry for MMP platform
ARM: mmp/mmp2: fix cpu_is_mmp2() on mmp2-dt
MAINTAINERS: mediatek: Update SoC entry
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
+ Linux 4.20-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
checkpatch.pl reports the following:
WARNING: struct kgdb_arch should normally be const
#28: FILE: arch/mips/kernel/kgdb.c:397:
+struct kgdb_arch arch_kgdb_ops = {
This report makes sense, as all other ops struct, this
one should also be const. This patch does the change.
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: x86@kernel.org
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
When I had lockdep turned on and dropped into kgdb I got a nice splat
on my system. Specifically it hit:
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
Specifically it looked like this:
sysrq: SysRq : DEBUG
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
WARNING: CPU: 0 PID: 0 at .../kernel/locking/lockdep.c:2875 lockdep_hardirqs_on+0xf0/0x160
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.0 #27
pstate: 604003c9 (nZCv DAIF +PAN -UAO)
pc : lockdep_hardirqs_on+0xf0/0x160
...
Call trace:
lockdep_hardirqs_on+0xf0/0x160
trace_hardirqs_on+0x188/0x1ac
kgdb_roundup_cpus+0x14/0x3c
kgdb_cpu_enter+0x53c/0x5cc
kgdb_handle_exception+0x180/0x1d4
kgdb_compiled_brk_fn+0x30/0x3c
brk_handler+0x134/0x178
do_debug_exception+0xfc/0x178
el1_dbg+0x18/0x78
kgdb_breakpoint+0x34/0x58
sysrq_handle_dbg+0x54/0x5c
__handle_sysrq+0x114/0x21c
handle_sysrq+0x30/0x3c
qcom_geni_serial_isr+0x2dc/0x30c
...
...
irq event stamp: ...45
hardirqs last enabled at (...44): [...] __do_softirq+0xd8/0x4e4
hardirqs last disabled at (...45): [...] el1_irq+0x74/0x130
softirqs last enabled at (...42): [...] _local_bh_enable+0x2c/0x34
softirqs last disabled at (...43): [...] irq_exit+0xa8/0x100
---[ end trace adf21f830c46e638 ]---
Looking closely at it, it seems like a really bad idea to be calling
local_irq_enable() in kgdb_roundup_cpus(). If nothing else that seems
like it could violate spinlock semantics and cause a deadlock.
Instead, let's use a private csd alongside
smp_call_function_single_async() to round up the other CPUs. Using
smp_call_function_single_async() doesn't require interrupts to be
enabled so we can remove the offending bit of code.
In order to avoid duplicating this across all the architectures that
use the default kgdb_roundup_cpus(), we'll add a "weak" implementation
to debug_core.c.
Looking at all the people who previously had copies of this code,
there were a few variants. I've attempted to keep the variants
working like they used to. Specifically:
* For arch/arc we passed NULL to kgdb_nmicallback() instead of
get_irq_regs().
* For arch/mips there was a bit of extra code around
kgdb_nmicallback()
NOTE: In this patch we will still get into trouble if we try to round
up a CPU that failed to round up before. We'll try to round it up
again and potentially hang when we try to grab the csd lock. That's
not new behavior but we'll still try to do better in a future patch.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
The function kgdb_roundup_cpus() was passed a parameter that was
documented as:
> the flags that will be used when restoring the interrupts. There is
> local_irq_save() call before kgdb_roundup_cpus().
Nobody used those flags. Anyone who wanted to temporarily turn on
interrupts just did local_irq_enable() and local_irq_disable() without
looking at them. So we can definitely remove the flags.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries
by Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right Kconfig
files. This series instead just selects the presence (when needed) and
then handles everything in the bus-specific Kconfig file under drivers/.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WxId
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig file consolidation from Masahiro Yamada:
"Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries by
Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right
Kconfig files. This series instead just selects the presence (when
needed) and then handles everything in the bus-specific Kconfig file
under drivers/"
* tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
pcmcia: remove per-arch PCMCIA config entry
eisa: consolidate EISA Kconfig entry in drivers/eisa
rapidio: consolidate RAPIDIO config entry in drivers/rapidio
pcmcia: allow PCMCIA support independent of the architecture
PCI: consolidate the PCI_SYSCALL symbol
PCI: consolidate the PCI_DOMAINS and PCI_DOMAINS_GENERIC config options
PCI: consolidate PCI config entry in drivers/pci
MIPS: remove the HT_PCI config option
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
Krzysztof Kozlowski