Printing the event parameters in decimal is not useful.
Print them in hex and make it more practical.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720215113.1058313-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove USB EHCI host controller reset sequence from NPCM7XX USB EHCI
host probe function because it is done in the NPCM reset driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20220718181842.61040-2-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens when @udev->reset_resume is set to true, when usb resume,
the flow as below:
- hub_resume
- usb_disable_interface
- usb_disable_endpoint
- usb_hcd_disable_endpoint
- xhci_endpoint_disable // it set @ep->hcpriv to NULL
Then when reset usb device, it will drop allocated endpoints,
the flow as below:
- usb_reset_and_verify_device
- usb_hcd_alloc_bandwidth
- xhci_mtk_drop_ep
but @ep->hcpriv is already set to NULL, the bandwidth will be not
released anymore.
Due to the added endponts are stored in hash table, we can drop the check
of @ep->hcpriv.
Fixes: 4ce186665e ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220819080556.32215-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently uses the worst case byte budgets on FS/LS bus bandwidth,
for example, for an isochronos IN endpoint with 192 bytes budget, it
will consume the whole 5 uframes(188 * 5) while the actual FS bus
budget should be just 192 bytes. It cause that many usb audio headsets
with 3 interfaces (audio input, audio output, and HID) cannot be
configured.
To improve it, changes to use "approximate" best case budget for FS/LS
bandwidth management. For the same endpoint from the above example,
the approximate best case budget is now reduced to (188 * 2) bytes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220819080556.32215-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err_probe message. Fix it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220803123018.913710-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual
Flash LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the Type-C & Power Delivery controller in
MediaTek MT6370 IC.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Link: https://lore.kernel.org/r/20220815090125.27705-8-peterwu.pub@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7505a9dfa1e097070c492d6f6f84afa2a490b040.1659763173.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
onboard_hub_power_off() currently has a delay after asserting the
reset of the hub. There is already a delay in onboard_hub_power_on()
before de-asserting the reset, which ensures that the reset is
asserted for the required time, so the delay in _power_off() is not
needed.
Skip the reset GPIO check before calling gpiod_set_value_cansleep(),
the function returns early when the GPIO descriptor is NULL.
Reviewed-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220805111836.1.Id5a4dc0a2c046236116693aa55672295513a0f2a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary PCI device ID for the controller
inside the Intel Raptor Lake CPU block. The controllers that
are part of the PCH (chipset) have separate device IDs.
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220815123334.87526-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary ACPI ID for Intel Meteor Lake
IOM devices.
The callback function is_memory() is modified so that it
also checks if the resource descriptor passed to it is a
memory type "Address Space Resource Descriptor".
On Intel Meteor Lake the ACPI memory resource is not
described using the "32-bit Memory Range Descriptor" because
the memory is outside of the 32-bit address space. The
memory resource is described using the "Address Space
Resource Descriptor" instead.
Intel Meteor Lake is the first platform to describe the
memory resource for this device with Address Space Resource
Descriptor, but it most likely will not be the last.
Therefore the change to the is_memory() callback function
is made generic.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable@vger.kernel.org
[ heikki: Rewrote the commit message. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220816101629.69054-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the suspend callbacks by separating the error and success paths
to improve readability.
Also drop a related redundant initialisation.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is the Qualcomm glue wakeup interrupts that may be able to wake the
system from suspend and this can now be described in the devicetree.
Move the wakeup-source property handling over from the core driver and
instead propagate the capability setting to the core device during
probe.
This is needed as there is currently no way for the core driver to query
the wakeup setting of the glue device, but it is the core driver that
manages the PHY power state during suspend.
Also don't leave the PHYs enabled when system wakeup has been disabled
through sysfs.
Fixes: 649f5c842b ("usb: dwc3: core: Host wake up support from system suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit implementing wakeup support in host mode instead broke
suspend for peripheral and OTG mode.
The hack that was added in the suspend path to determine the speed of
any device connected to the USB2 bus not only accesses internal driver
data for a child device, but also dereferences a NULL pointer or
accesses freed data when the controller is not acting as host.
There's no quick fix to the layering violation, but since reverting
would leave us with broken suspend in host mode with wakeup triggering
immediately, let's keep the hack for now.
Fix the immediate issues by only checking the host bus speed and
enabling wakeup interrupts when acting as host.
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A device must enable wakeups during runtime suspend regardless of
whether it is capable and allowed to wake the system up from system
suspend.
Fixes: 2664deb093 ("usb: dwc3: qcom: Honor wakeup enabled/disabled state")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.
After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.
Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.
Also note that runtime PM has been broken since commit 2664deb093
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change added a dependency to the USB host stack and broke
gadget-only builds of the driver.
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d9be8d5c5b.
Generic power-domain flags must be set before the power-domain is
initialised and must specifically not be modified by drivers for devices
that happen to be in the domain.
To make sure that USB power-domains are left enabled during system
suspend when a device in the domain is in the wakeup path, the
GENPD_FLAG_ACTIVE_WAKEUP flag should instead be set for the domain
unconditionally when it is registered.
Note that this also avoids keeping power-domains on during suspend when
wakeup has not been enabled (e.g. through sysfs).
For the runtime PM case, making sure that the PHYs are not suspended and
that they are in the same domain as the controller prevents the domain
from being suspended. If there are cases where this is not possible or
desirable, the genpd implementation may need to be extended.
Fixes: d9be8d5c5b ("usb: dwc3: qcom: Keep power domain on to retain controller status")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHYs must be powered-off before they can be tore down.
Similarly, suspending legacy PHYs after having powered them off makes no
sense.
Fix the dwc3_core_exit() (e.g. called during suspend) and open-coded
dwc3_probe() error-path sequences that got this wrong.
Note that this makes dwc3_core_exit() match the dwc3_core_init() error
path with respect to powering off the PHYs.
Fixes: 03c1fd622f ("usb: dwc3: core: add phy cleanup for probe error handling")
Fixes: c499ff71ff ("usb: dwc3: core: re-factor init and exit paths")
Cc: stable@vger.kernel.org # 4.8
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is USB mass storage primary boot loader for code download on
NXP PN7462AU.
Without the quirk it is impossible to write whole memory at once as
device restarts during the write due to bogus residue values reported.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Witold Lipieta <witold.lipieta@thaumatec.com>
Link: https://lore.kernel.org/r/20220809112911.462776-1-witold.lipieta@thaumatec.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the port does not support USB PD, prevent transition to PD
only states when power supply property is written. In this case,
TCPM transitions to SNK_NEGOTIATE_CAPABILITIES
which should not be the case given that the port is not pd_capable.
[ 84.308251] state change SNK_READY -> SNK_NEGOTIATE_CAPABILITIES [rev3 NONE_AMS]
[ 84.308335] Setting usb_comm capable false
[ 84.323367] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:5000 ret:0
[ 84.323376] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
Fixes: e9e6e164ed ("usb: typec: tcpm: Support non-PD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220817215410.1807477-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning on NOP_USB_XCEIV as builtin broke the TUSB6010 driver because
of an older issue with the depencency.
It is not necessary to forbid NOP_USB_XCEIV=y in combination with
USB_MUSB_HDRC=m, but only the reverse, which causes the link failure
from the original Kconfig change.
Use the correct dependency to still allow NOP_USB_XCEIV=n or
NOP_USB_XCEIV=y but forbid NOP_USB_XCEIV=m when USB_MUSB_HDRC=m
to fix the multi_v7_defconfig for tusb.
Fixes: ab37a7a890 ("ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in")
Fixes: c044247965 ("usb: musb: Fix randconfig build issues for Kconfig options")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220818135737.3143895-10-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make the
tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo). Also
included in here is the obligatory n_gsm updates from Daniel Starke and
lots of tiny driver updates and minor fixes and tweaks for other smaller
serial drivers.
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYvD8qA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfEQCdGiYLQkWUUarhnlocHo+kSm5vkvsAnicZg7Sl
IQBeAidA3dZEQO0lLlM5
=t7Yh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
- convert arm32 to the common dma-direct code (Arnd Bergmann, Robin Murphy,
Christoph Hellwig)
- restructure the PCIe peer to peer mapping support (Logan Gunthorpe)
- allow the IOMMU code to communicate an optional DMA mapping length
and use that in scsi and libata (John Garry)
- split the global swiotlb lock (Tianyu Lan)
- various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
Lukas Bulwahn, Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=Bv19
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- convert arm32 to the common dma-direct code (Arnd Bergmann, Robin
Murphy, Christoph Hellwig)
- restructure the PCIe peer to peer mapping support (Logan Gunthorpe)
- allow the IOMMU code to communicate an optional DMA mapping length
and use that in scsi and libata (John Garry)
- split the global swiotlb lock (Tianyu Lan)
- various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
Lukas Bulwahn, Robin Murphy)
* tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping: (45 commits)
swiotlb: fix passing local variable to debugfs_create_ulong()
dma-mapping: reformat comment to suppress htmldoc warning
PCI/P2PDMA: Remove pci_p2pdma_[un]map_sg()
RDMA/rw: drop pci_p2pdma_[un]map_sg()
RDMA/core: introduce ib_dma_pci_p2p_dma_supported()
nvme-pci: convert to using dma_map_sgtable()
nvme-pci: check DMA ops when indicating support for PCI P2PDMA
iommu/dma: support PCI P2PDMA pages in dma-iommu map_sg
iommu: Explicitly skip bus address marked segments in __iommu_map_sg()
dma-mapping: add flags to dma_map_ops to indicate PCI P2PDMA support
dma-direct: support PCI P2PDMA pages in dma-direct map_sg
dma-mapping: allow EREMOTEIO return code for P2PDMA transfers
PCI/P2PDMA: Introduce helpers for dma_map_sg implementations
PCI/P2PDMA: Attempt to set map_type if it has not been set
lib/scatterlist: add flag for indicating P2PDMA segments in an SGL
swiotlb: clean up some coding style and minor issues
dma-mapping: update comment after dmabounce removal
scsi: sd: Add a comment about limiting max_sectors to shost optimal limit
ata: libata-scsi: cap ata_device->max_sectors according to shost->max_sectors
scsi: scsi_transport_sas: cap shost opt_sectors according to DMA optimal limit
...
- Runtime verification infrastructure
This is the biggest change for this pull request. It introduces the
runtime verification that is necessary for running Linux on safety
critical systems. It allows for deterministic automata models to be
inserted into the kernel that will attach to tracepoints, where the
information on these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will then
activate a given reactor, that could just inform the user or even panic
the kernel (for which safety critical systems will detect and can recover
from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to be
confused with "work in progress"), and Wakeup While Not Running (WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace several
vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is left
off.
- The rest is various cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYu0yzRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qj4HAP4tQtV55rjj4DQ5XIXmtI3/64PmyRSJ
+y4DEXi1UvEUCQD/QAuQfWoT/7gh35ltkfeS4t3ockzy14rrkP5drZigiQA=
=kEtM
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Runtime verification infrastructure
This is the biggest change here. It introduces the runtime
verification that is necessary for running Linux on safety critical
systems.
It allows for deterministic automata models to be inserted into the
kernel that will attach to tracepoints, where the information on
these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will
then activate a given reactor, that could just inform the user or
even panic the kernel (for which safety critical systems will detect
and can recover from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to
be confused with "work in progress"), and Wakeup While Not Running
(WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace
several vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is
left off.
- The rest is various cleanups and fixes.
* tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits)
rv: Unlock on error path in rv_unregister_reactor()
tracing: Use alignof__(struct {type b;}) instead of offsetof()
tracing/eprobe: Show syntax error logs in error_log file
scripts/tracing: Fix typo 'the the' in comment
tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT
tracing: Use free_trace_buffer() in allocate_trace_buffers()
tracing: Use a struct alignof to determine trace event field alignment
rv/reactor: Add the panic reactor
rv/reactor: Add the printk reactor
rv/monitor: Add the wwnr monitor
rv/monitor: Add the wip monitor
rv/monitor: Add the wip monitor skeleton created by dot2k
Documentation/rv: Add deterministic automata instrumentation documentation
Documentation/rv: Add deterministic automata monitor synthesis documentation
tools/rv: Add dot2k
Documentation/rv: Add deterministic automaton documentation
tools/rv: Add dot2c
Documentation/rv: Add a basic documentation
rv/include: Add instrumentation helper functions
rv/include: Add deterministic automata monitor definition via C macros
...
Pull AVR32 updates from Hans-Christian Noren Egtvedt:
"Mostly changes to documentation and comments"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
video:backlight: remove reference to AVR32 architecture in ltv350qv
video: remove support for non-existing atmel,at32ap-lcdc in atmel_lcdfb
usb:udc: remove reference to AVR32 architecture in Atmel USBA Kconfig
sound:spi: remove reference to AVR32 in Atmel AT73C213 DAC driver
net: remove cdns,at32ap7000-macb device tree entry
misc: update maintainer email address and description for atmel-ssc
mfd: remove reference to AVR32 architecture in atmel-smc.c
dma:dw: remove reference to AVR32 architecture in core.c
Clang warns:
drivers/usb/cdns3/cdns3-gadget.c:2290:11: error: variable 'priv_dev' is uninitialized when used here [-Werror,-Wuninitialized]
dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
^~~~~~~~
include/linux/dev_printk.h:155:18: note: expanded from macro 'dev_dbg'
dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:167:7: note: expanded from macro 'dynamic_dev_dbg'
dev, fmt, ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:152:56: note: expanded from macro '_dynamic_func_call'
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~
include/linux/dynamic_debug.h:134:15: note: expanded from macro '__dynamic_func_call'
func(&id, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/usb/cdns3/cdns3-gadget.c:2278:31: note: initialize the variable 'priv_dev' to silence this warning
struct cdns3_device *priv_dev;
^
= NULL
1 error generated.
The priv_dev assignment was moved below the if statement to avoid
potentially dereferencing ep before it was checked but priv_dev is used
in the dev_dbg() call.
To fix this, move the priv_dev and comp_desc assignments back to their
original spot and hoist the ep check above those assignments with a call
to pr_debug() instead of dev_dbg().
Fixes: c3ffc9c4ca ("usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()")
Link: https://github.com/ClangBuiltLinux/linux/issues/1680
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development on
some new hardware support and cleanups of older drivers. Highlights of
this pull request are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this
tool it seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted
as they depened on some typec changes, but the cross-tree
merges caused problems so they will come back later through
the platform tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYup5Rg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yko/ACfYD9mdlr4WleUpVw5/uNywN6sL9EAn1tv0V8W
cUTAoWxAf5orClAC22ZU
=Vcqd
-----END PGP SIGNATURE-----
Merge tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
The AVR32 architecture does no longer exist in the Linux kernel, hence
remove a reference to it in Kconfig help text to avoid confusion.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Merge ACPI device object management changes for v5.20-rc1.
- Use the facilities provided by the driver core and some additional
helpers to handle the children of a given ACPI device object in
multiple places instead of using the children and node list heads in
struct acpi_device which is error prone (Rafael Wysocki).
- Fix ACPI-related device reference counting issue in the hisi_lpc bus
driver (Yang Yingliang).
- Drop the children and node list heads that are not needed any more
from struct acpi_device (Rafael Wysocki).
- Drop driver member from struct acpi_device (Uwe Kleine-König).
- Drop redundant check from acpi_device_remove() (Uwe Kleine-König).
* acpi-bus:
ACPI: bus: Drop unused list heads from struct acpi_device
hisi_lpc: Use acpi_dev_for_each_child()
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
ACPI: bus: Drop driver member of struct acpi_device
ACPI: bus: Drop redundant check in acpi_device_remove()
mfd: core: Use acpi_dev_for_each_child()
ACPI / MMC: PM: Unify fixing up device power
soundwire: Use acpi_dev_for_each_child()
platform/x86/thinkpad_acpi: Use acpi_dev_for_each_child()
ACPI: scan: Walk ACPI device's children using driver core
ACPI: bus: Introduce acpi_dev_for_each_child_reverse()
ACPI: video: Use acpi_dev_for_each_child()
ACPI: bus: Export acpi_dev_for_each_child() to modules
ACPI: property: Use acpi_dev_for_each_child() for child lookup
ACPI: container: Use acpi_dev_for_each_child()
USB: ACPI: Replace usb_acpi_find_port() with acpi_find_child_by_adr()
thunderbolt: ACPI: Replace tb_acpi_find_port() with acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_dev_has_children()
ACPI: glue: Use acpi_dev_for_each_child()
onboard_hub_power_on() already ensures the reset pulse width delay, so
there is no need to wait right after requesting GPIO as well.
Fixes: 40758e493f ("usb: misc: onboard_usb_hub: Add reset-gpio support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220728064937.917935-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Despite default reset upon probe, release reset line after powering up
the hub and assert reset again before powering down.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220727141117.909361-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Microchip USB2514B USB 2.0 hub to the onboard usb hub
driver. Adopt the generic usb-device compatible ("usbVID,PID").
Some STM32MP1 boards have this hub on-board, with a supply that needs to
be enabled for proper operation.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220726080708.162547-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32G0 comes with STM32 bootloader in its system memory. Add support
for some I2C bootloader commands as described in application notes
AN2606 and AN4221, to enable STM32G0 UCSI firmware update.
Upon probing, the driver needs to know the STM32G0 state:
- In bootloader mode, STM32 G0 answers at i2c addr 0x51.
- In running mode, STM32 G0 firmware may answer at two address.
- The main address specified in DT is used for UCSI.
- 0x51 addr can be re-used for FW controls like getting software version
or jump to booloader request.
So probe using the main firmware i2c address first, before attempting
bootloader address (e.g. check for blank, erased or previously aborted
firmware update).
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220713120842.560902-4-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32G0 provides an integrated USB Type-C and power delivery interface.
It can be programmed with a firmware to handle UCSI protocol over I2C
interface. A GPIO is used as an interrupt line.
Type-C connector can be used as a wakeup source (typically to detect
changes on the port, like attach or detach). PM suspend / resume routines
are used to enable wake irqs, and signal a wakeup event in case the IRQ
has fired while in suspend. The i2c core is doing the necessary
initialization when the "wakeup-source" flag is provided.
Note: the interrupt handler shouldn't be called before the i2c bus resumes.
So, the interrupts are disabled during suspend period, and re-enabled
upon resume, to avoid i2c transfer while suspended, from the irq handler.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220713120842.560902-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found PPM will not send any notification after it report error status
and OPM issue GET_ERROR_STATUS command to read the details about error.
According UCSI spec, PPM may clear the Error Status Data after the OPM
has acknowledged the command completion.
This change add operation to acknowledge the command completion from PPM.
Fixes: bdc62f2bae (usb: typec: ucsi: Simplified registration and I/O API)
Cc: <stable@vger.kernel.org> # 5.10
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1658817949-4632-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'ep' is NULL, result of ep_to_cdns3_ep(ep) is invalid pointer
and its dereference with priv_ep->cdns3_dev may cause panic.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Andrey Strachuk <strochuk@ispras.ru>
Link: https://lore.kernel.org/r/20220718160052.4188-1-strochuk@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fwnode_connection_find_match() function handles two cases: named
references and graph endpoints. In the second case, the match function
passed in is called with the id to check for the match. However, the
match function for the recently added type-c retimer class assumes the
connection has already been matched (which is only true for the first
case).
The result is that with that change, all type-c nodes with graph
endpoints defer probe indefinitely, independently of having a retimer
connection or not.
Add the missing check, like is done by the type-c mux and usb role
switch code, to fix the issue.
Fixes: ddaf8d96f9 ("usb: typec: Add support for retimers")
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220725203129.1973260-1-nfraprado@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer found a race between uevent callbacks and gadget
driver unregistration that can cause a use-after-free bug:
---------------------------------------------------------------
BUG: KASAN: use-after-free in usb_udc_uevent+0x11f/0x130
drivers/usb/gadget/udc/core.c:1732
Read of size 8 at addr ffff888078ce2050 by task udevd/2968
CPU: 1 PID: 2968 Comm: udevd Not tainted 5.19.0-rc4-next-20220628-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
06/29/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x719 mm/kasan/report.c:433
kasan_report+0xbe/0x1f0 mm/kasan/report.c:495
usb_udc_uevent+0x11f/0x130 drivers/usb/gadget/udc/core.c:1732
dev_uevent+0x290/0x770 drivers/base/core.c:2424
---------------------------------------------------------------
The bug occurs because usb_udc_uevent() dereferences udc->driver but
does so without acquiring the udc_lock mutex, which protects this
field. If the gadget driver is unbound from the udc concurrently with
uevent processing, the driver structure may be accessed after it has
been deallocated.
To prevent the race, we make sure that the routine holds the mutex
around the racing accesses.
Link: <https://lore.kernel.org/all/0000000000004de90405a719c951@google.com>
CC: stable@vger.kernel.org # fc274c1e99
Reported-and-tested-by: syzbot+b0de012ceb1e2a97891b@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YtlrnhHyrHsSky9m@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb core introduce the mechanism of giveback of URB in tasklet context to
reduce hardware interrupt handling time. On some test situation(such as
FIO with 4KB block size), when tasklet callback function called to
giveback URB, interrupt handler add URB node to the bh->head list also.
If check bh->head list again after finish all URB giveback of local_list,
then it may introduce a "dynamic balance" between giveback URB and add URB
to bh->head list. This tasklet callback function may not exit for a long
time, which will cause other tasklet function calls to be delayed. Some
real-time applications(such as KB and Mouse) will see noticeable lag.
In order to prevent the tasklet function from occupying the cpu for a long
time at a time, new URBS will not be added to the local_list even though
the bh->head list is not empty. But also need to ensure the left URB
giveback to be processed in time, so add a member high_prio for structure
giveback_urb_bh to prioritize tasklet and schelule this tasklet again if
bh->head list is not empty.
At the same time, we are able to prioritize tasklet through structure
member high_prio. So, replace the local high_prio_bh variable with this
structure member in usb_hcd_giveback_urb.
Fixes: 94dfd7edfd ("USB: HCD: support giveback of URB in tasklet context")
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220726074918.5114-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If i2c_new_dummy_device() fails, it never return NULL pointer, replace
NULL test with IS_ERR() to fix it.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220721071201.269344-2-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should be 'ctx->typec.amode[i]' passed to PTR_ERR() when
typec_partner_register_altmode() failed.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220721071201.269344-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Semi colons and commas are equivalent in this context but semi-colons
are better style.
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtpD4MKBa43higNc@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a minor bug which means that certain error messages are not
printed.
The devm_gpiod_get_optional() function can return either error pointers
or NULL. It returns error pointers if there is an allocation failure,
or a similar issue. It returns NULL if no GPIO was assigned to the
requested function. Print an error in either case.
The gpiod_to_irq() function never returns zero. It either returns
a positive IRQ number or a negative error code.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtpDs8VsWIbl/Smd@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should be ARRAY_SIZE() instead of sizeof(). ARRAY_SIZE is
4 and sizeof is 8.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtpC5s4/AD8vFz+X@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the result of the & operation back to the
variable var. The store is redundant, replace &= with just &.
Cleans up clang scan warning:
drivers/usb/phy/phy-keystone.c:62:5: warning: Although the value stored to
'val' is used in the enclosing expression, the value is never actually read
from 'val' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220715225657.353828-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.20-rc1, including
- a fix up of some tty-port initialized comments that had got
truncated and obfuscated
Included are also various clean ups.
All but the final commit have been in linux-next and with no reported
issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYt5e7QAKCRALxc3C7H1l
CFcWAP4hjc2GHm3VuQNISc31CP2NeLW/DVMIlhc2xOEF0bRTPwEAnYtuPajGjbPL
ED42eNCA7vcLG3Q8HaxTI9cEjujacQw=
=1/u0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.20-rc1
Here are the USB-serial updates for 5.20-rc1, including
- a fix up of some tty-port initialized comments that had got
truncated and obfuscated
Included are also various clean ups.
All but the final commit have been in linux-next and with no reported
issues.
* tag 'usb-serial-5.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: fix tty-port initialized comments
USB: serial: fix repeated word "the" in comments
USB: serial: io_edgeport: fix spelling mistakes
USB: serial: use kmemdup instead of kmalloc + memcpy
Fix up the tty-port initialized comments which got truncated and
obfuscated when replacing the old ASYNCB_INITIALIZED flag.
Fixes: d41861ca19 ("tty: Replace ASYNC_INITIALIZED bit and update atomically")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220719112719.17e796c6@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224750.532345354@goodmis.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224750.172301548@goodmis.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.991587733@goodmis.org
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Similar to mux and orientation switch, add a handle for registered
retimer to the port, so that it has handles to the various switches
connected to it.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220711072333.2064341-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a retimer device class and associated functions that register
and use retimer "switch" devices. These operate in a manner similar to
the "mode-switch" and help configure retimers that exist between the
Type-C connector and host controller(s).
Type C ports can be linked to retimers using firmware node device
references (again, in a manner similar to "mode-switch").
There are no new sysfs files being created; there is the new retimer
class directory, but there are no class-specific files being created
there.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220711072333.2064341-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of new device ids for ftdi_sio.
Everything has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYtAiWQAKCRALxc3C7H1l
CNIlAQCpzqXHrTW4VQLy5Usnei8bqBelPtAfTTqQ13n66ZIlSwD+JdYSwpJCWJCa
bg6XTyJ0ON5CJAeZ0kT4pG0MPtmrDAw=
=YFjC
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.19-rc7
Here are a couple of new device ids for ftdi_sio.
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-5.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add Belimo device ids
Not all platforms have all of the four currently supported wakeup
interrupts so use the optional irq helpers when looking up interrupts to
avoid printing error messages when an optional interrupt is not found:
dwc3-qcom a6f8800.usb: error -ENXIO: IRQ hs_phy_irq not found
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220713131340.29401-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for analogix ANX7411 USB Type-C DRP port controller.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Link: https://lore.kernel.org/r/20220714081350.36447-2-xji@analogixsemi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the programming guide, it is recommended to
perform a GCTL_CORE_SOFTRESET only when switching the mode
from device to host or host to device. However, it is found
that during bootup when __dwc3_set_mode() is called for the
first time, GCTL_CORESOFTRESET is done with suspendable bit(BIT 17)
of DWC3_GUSB3PIPECTL set. This some times leads to issues
like controller going into bad state and controller registers
reading value zero. Until GCTL_CORESOFTRESET is done and
run/stop bit is set core initialization is not complete.
Setting suspendable bit of DWC3_GUSB3PIPECTL and then
performing GCTL_CORESOFTRESET is therefore not recommended.
Avoid this by only performing the reset if current_dr_role is set,
that is, when doing subsequent role switching.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Signed-off-by: Rohith Kollalsi <quic_rkollals@quicinc.com>
Link: https://lore.kernel.org/r/20220714045625.20377-1-quic_rkollals@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should call of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: 30d2617fd7 ("usb: gadget: aspeed: allow to set usb strings in device tree")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220713120528.368168-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following coccicheck warning:
drivers/usb/misc/ldusb.c:719: WARNING opportunity for max().
drivers/usb/misc/ldusb.c:721: WARNING opportunity for max().
max_t() macro is defined in include/linux/minmax.h. It avoids
multiple evaluations of the arguments when non-constant and performs
strict type-checking.
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Link: https://lore.kernel.org/r/20220713070205.3047256-1-13667453960@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a 3 stage SETUP transfer, if the host sends another SETUP token
before completing the status phase, it signifies that the host has aborted
the current control transfer. Currently, if a setup_packet_pending is
received, there are no subsequent calls to dwc3_ep0_out_start() to fetch
the new SETUP packet. This leads to a stall on EP0, as host does not
expect another STATUS phase as it has aborted the current transfer.
Fix this issue by explicitly stalling and restarting EP0, as well as
resetting the trb_enqueue indexes. (without this, there is a chance the
SETUP TRB is set up on trb_endqueue == 1)
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220712014403.2977-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with 'W=1' the compiler complains about missing
prototypes for onboard_hub_create/destroy_pdevs(). Include the
header with the prototypes to fix this.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220711092431.1.I4016c759fd7fe2b32dd482994a20661f36e2cae3@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows to reset prevent_medium_removal flag and "eject" the image.
This can be useful to free the drive from a hunging host or if the host
continues to use the drive even after unmounting (Linux does this).
It's also a bit like using an unfolded paperclip on an optical drive.
Previously, the undocumented method of sending SIGUSR1 to a special
"file-storage" kernel thread could be used for these purposes,
but when using multiple storages there was no way to distinguish
one from the other, so we had to send a signal to everyone.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20220711102956.19642-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a repeated word "the" in two comments that should be replaced
or removed.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
[ johan: replace one "the" with "that", merge the two cleanups, amend
commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Those two product ids are known.
Signed-off-by: Lucien Buchmann <lucien.buchmann@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
For High-Speed Transfers the prepare_one_trb function is calculating the
multiplier setting for the trb based on the length parameter of the trb
currently prepared. This assumption is wrong. For trbs with a sg list,
the length of the actual request has to be taken instead.
Fixes: 40d829fb2e ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function __dwc3_prepare_one_trb has many parameters. Since it is
only used in dwc3_prepare_one_trb there is no point in keeping the
function. We merge both functions and get rid of the big list of
parameters.
Fixes: 40d829fb2e ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In patch a1a2b7125e (Drop static setup of IRQ resource from DT
core) we stopped platform_get_resource() from returning the IRQ, as all
drivers were supposed to have switched to platform_get_irq()
Unfortunately the Freescale EHCI driver in host mode got missed. Fix
it.
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Suggested-by: Rob Herring <robh@kernel.org>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Link: https://lore.kernel.org/r/20220702220355.63b36fb8@Cyrus.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting the function name, it is always truncated by one char since
snprintf is always including the null-termination in the len parameter.
We use strscpy and fix the size setting to use len + 1 instead.
Fixes: 324e4f8507 ("usb: gadget: uvc: allow changing interface name via configfs")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220707115612.2760569-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System like Android allow user control power role from UI, it is possible
to implement application base on typec uevent to refresh UI, but found
there is chance that UI show different state from typec attribute file.
In typec_set_pwr_opmode(), when partner support PD, there is no uevent
send to user space which cause the problem.
Fix it by sending uevent notification when change power mode to PD.
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Cc: stable@vger.kernel.org
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1656662934-10226-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call onboard_hub_create/destroy_pdevs() from hub_probe/disconnect()
to create/destroy platform devices for onboard USB hubs that may be
connected to the hub. The onboard hubs must have nodes in the
device tree.
onboard_hub_create/destroy_pdevs() are NOPs unless
CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct usb_hub to keep track of the onboard hub
platform devices that are owned by the hub.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.4.Ic9dd36078f9d803de82ca01a6700c58b8e4de27e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.3.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function wake notification to support function remote wakeup,
currently assume the composite device only enable function wake
for the first interface.
Forward request to function driver when the recipient is an interface,
including:
GetStatus() request to the first interface in a function returns the
information about 'function remote wakeup' and 'function remote wakeup
capalbe';
SetFeature request of FUNCTION_SUSPEND to an interface recipient, the
controller driver saves the suspend option;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-5-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is capable of supporting usb3 dual role if there is at least one
usb3 port for device and xhci controller, we can check it from the
controller's capability, so no need the property "mediatek,usb3-drd"
anymore, but I find the property is not decribed in dt-binding.
Meanwhile, also take into account if the u3 port is disabled when the
u3 phy is shared with pcie.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may want to disable device's usb3 port when the combo phy is switched
from usb3 mode to pcie mode for some projects.
Meanwhile rename member @is_u3_ip to @u3_capable to avoid misleading, due
to the member's value may be changed when disable usb3 port, but the
controller is still a usb3 IP which also tells us how to manage the fifo.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB PD controllers which consisting of a microcontroller (acting as the TCPM)
and a port controller (TCPC) - may require that the driver for the PD
controller accesses directly also the on-chip port controller in some cases.
Move tcpci.h to include/linux/usb/ is convenience access TCPC registers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Link: https://lore.kernel.org/r/20220706083433.2415524-1-xji@analogixsemi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
after usb_ep_queue() if wait_for_completion_interruptible() is
interrupted we need to wait until IRQ gets finished.
Otherwise complete() from epio_complete() can corrupt stack.
Signed-off-by: Jozef Martiniak <jomajm@gmail.com>
Link: https://lore.kernel.org/r/20220708070645.6130-1-jomajm@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver won't probe on a LAN9668 because the pinctrl driver isn't
ready yet. Probe deferral is not supported because the init section
is already discarded. With fw_devlink enabled, the probe won't even
be called. Convert the driver to a proper platform driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220705131951.1388968-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event classes udc_log_ep and udc_log_req both declare:
__dynamic_array(char, name, UDC_TRACE_STR_MAX)
Which will reserve UDC_TRACE_STR_MAX bytes on the ring buffer for the
event to write in name. It then uses snprintf() to write into that space.
Assuming that the string being copied is nul terminated, it is better to
just use the __string() helper. That way only the size of the string is
saved into the ring buffer and not the max size (yes, the entire
UDC_TRACE_STR_MAX is used in the trace event, and anything not used is
just junk in the ring buffer). Worse, there's also meta data saved into
the event that denotes where the string is stored in the event and also
saves its size, which is always going to be UDC_TRACE_STR_MAX.
Convert both to use the __string() and __assign_str() helpers that are for
this kind of use case.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20220703091449.317f94b1@rorschach.local.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sa1111 platform is one of the two remaining users of the old Arm
specific "dmabounce" code, which is an earlier implementation of the
generic swiotlb.
Linus Walleij submitted a patch that removes dmabounce support from
the ixp4xx, and I had a look at the other user, which is the sa1111
companion chip.
Looking at how dmabounce is used, I could narrow it down to one driver
one three machines:
- dmabounce is only initialized on assabet/neponset, jornada720 and
badge4, which are the platforms that have an sa1111 and support
DMA on it.
- All three of these suffer from "erratum #7" that requires only
doing DMA to half the memory sections based on one of the address
lines, in addition, the neponset also can't DMA to the RAM that
is connected to sa1111 itself.
- the pxa lubbock machine also has sa1111, but does not support DMA
on it and does not set dmabounce.
- only the OHCI and audio devices on sa1111 support DMA, but as
there is no audio driver for this hardware, only OHCI remains.
In the OHCI code, I noticed that two other platforms already have
a local bounce buffer support in the form of the "local_mem"
allocator. Specifically, TMIO and SM501 use this on a few other ARM
boards with 16KB or 128KB of local SRAM that can be accessed from the
OHCI and from the CPU.
While this is not the same problem as on sa1111, I could not find a
reason why we can't re-use the existing implementation but replace the
physical SRAM address mapping with a locally allocated DMA buffer.
There are two main downsides:
- rather than using a dynamically sized pool, this buffer needs
to be allocated at probe time using a fixed size. Without
having any idea of what it should be, I picked a size of
64KB, which is between what the other two OHCI front-ends use
in their SRAM. If anyone has a better idea what that size
is reasonable, this can be trivially changed.
- Previously, only USB transfers to unaddressable memory needed
to go through the bounce buffer, now all of them do, which may
impact runtime performance for USB endpoints that do a lot of
transfers.
On the upside, the local_mem support uses write-combining buffers,
which should be a bit faster for transfers to the device compared to
normal uncached coherent memory as used in dmabounce.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit cbf286e8ef ("xhci: fix unsafe memory usage in xhci tracing")
apparently missed one sprintf() call in xhci_decode_trb() -- replace
it with the snprintf() call as well...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Fixes: cbf286e8ef ("xhci: fix unsafe memory usage in xhci tracing")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220630124645.1805902-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clk get by devm_clk_get() will be released in devres_release_all(),
so there is no need explicitly call clk_put(), or it will cause UAF.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220629094635.3116961-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3_EVENT_PENDING flag is used to protect against invalid call to
top-half interrupt handler, which can occur when there's a delay in
software detection of the interrupt line deassertion.
However, the clearing of this flag was done prior to unmasking the
interrupt line, creating opportunity where the top-half handler can
come. This breaks the serialization and creates a race between the
top-half and bottom-half handler, resulting in losing synchronization
between the controller and the driver when processing events.
To fix this, make sure the clearing of the DWC3_EVENT_PENDING is done at
the end of the bottom-half handler.
Fixes: d325a1de49 ("usb: dwc3: gadget: Prevent losing events in event cache")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8670aaf1cf52e7d1e6df2a827af2d77263b93b75.1656380429.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add read TOC with format 1 to support CD-ROM emulation with
Windows OS.
This patch is tested on Windows OS Server 2019.
Fixes: 89ada0fe66 ("usb: gadget: f_mass_storage: Make CD-ROM emulation work with Mac OS-X")
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20220628021436.3252262-1-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a symbolic name for the standard timeout.
Use it. No functional change intended.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220629132638.31810-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clock source is prepared and enabled by clk_prepare_enable()
in probe function, but no disable or unprepare in remove.
Fixes: 7a96b6ea90 ("usb: musb: Add support for PolarFire SoC's musb controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220628140527.1404439-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug is that we should still enter this loop if "tx_len" is zero.
After adding the "last" variable, then the "chunk >= 0" condition is no
longer required but I left it for readability.
Fixes: c09b1f372e ("usb: gadget: aspeed_udc: cleanup loop in ast_dma_descriptor_setup()")
Reported-by: Neal Liu <neal_liu@aspeedtech.com>
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yrq6F5okoX1y05rT@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The multiplier parameter of dwc3_gadget_calc_tx_fifo_size() was
not documented:
drivers/usb/dwc3/gadget.c:675: warning: Function parameter or member 'mult' not described in 'dwc3_gadget_calc_tx_fifo_size'
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/bd599a18cea45c57d91c69d3e30d8b1e8ea69dd1.1656409369.git.mchehab@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a follow-up to the commit 4173f018aa (tty/vt: consolemap: rename
and document struct uni_pagedir), rename also the members of struct
vc_data. I.e. pagedir -> pagedict. And while touching all the places,
remove also the unnecessary vc_ prefix.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmK4zgIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrI8H+MeIYPff1m9vh1rZ
u1eCCtw/A+NqJ5l0Cq3Zj090crMb8zVkxr5QrdPxxJuxAK8AI/XzOUQivnNayp6v
bvWcbj9e95ZoIQjbPakozo3KYnaHXMFfrq6JNdGIBJ5yt5pVHtJ3iZk25wUZEghD
8lxoz4Uiuo14ZbLnlLjbXr5OEVupOH1OoQPghkSoolD8JBe1coOIYbzzJ69HBwNg
kCUyD0CsFCBpy0P7yBnPNrvQGOt+NVz9FLfEbYFj+ydQjzw3NNw7tyKTahqp7ScN
BS5Ftt0kuHqOyWDO9OP6dG1kGmvIWQZkrEroz1TS4FfgrrPRr5r0N9+tGvr9+tpZ
1tjaBA==
=L7lN
-----END PGP SIGNATURE-----
Merge 5.19-rc4 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The complete() function may be called even though request is not
completed. In this case, it's necessary to check request status so
as not to set device address wrongly.
Fixes: 10775eb17b ("usb: chipidea: udc: update gadget states according to ch9")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220623030242.41796-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-reading a recently merged fix to the raw_gadget driver showed that
it inadvertently introduced a double-free bug in a failure pathway.
If raw_ioctl_init() encounters an error after the driver ID number has
been allocated, it deallocates the ID number before returning. But
when dev_free() runs later on, it will then try to deallocate the ID
number a second time.
Closely related to this issue is another error in the recent fix: The
ID number is stored in the raw_dev structure before the code checks to
see whether the structure has already been initialized, in which case
the new ID number would overwrite the earlier value.
The solution to both bugs is to keep the new ID number in a local
variable, and store it in the raw_dev structure only after the check
for prior initialization. No errors can occur after that point, so
the double-free will never happen.
Fixes: f2d8c26068 ("usb: gadget: Fix non-unique driver names in raw-gadget driver")
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YrMrRw5AyIZghN0v@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix following includecheck warning:
./drivers/usb/gadget/function/u_ether.c: linux/etherdevice.h is included
more than once.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220623010808.9816-1-yang.lee@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
there is an unexpected word "the" in the comments that need to be dropped
file: ./drivers/usb/host/max3421-hcd.c
line: 315
* reasonable overview of how control transfers use the the IN/OUT
changed to:
* reasonable overview of how control transfers use the IN/OUT
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622103003.5420-1-jiangjian@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
there is an unexpected word "the" in the comments that need to be dropped
file: ./drivers/usb/dwc2/hcd.c
line: 1002
* even and the current frame number is even the the transfer
changed to:
* even and the current frame number is even the transfer
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622103558.6647-1-jiangjian@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using usb-role-switch, D+ pull-up is set as soon as DTCL_SFTDISCON is
cleared, whatever the vbus valid signal state is. The pull-up should not
be set when vbus isn't present (this is determined by the drd controller).
This patch ensures that B-Session (so Peripheral role + vbus valid signal)
is valid before clearing the DCTL_SFTDISCON bit when role switch is used.
Keep original behavior when usb-role-switch isn't used.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220622160717.314580-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These error paths return success but they need to return a negative
error code.
Fixes: 7a96b6ea90 ("usb: musb: Add support for PolarFire SoC's musb controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YrVmLEc/FOEzNdzj@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Meteor Lake TCSS(Type-C Subsystem) xHCI needs to be runtime suspended
whenever possible to allow the TCSS hardware block to enter D3cold and
thus save energy.
Cc: stable@kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Alder Lake TCSS (Type-C Subsystem) the Raptor
Lake TCSS xHCI needs to be runtime suspended whenever possible to
allow the TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@kernel.org
Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYrRX4AAKCRALxc3C7H1l
CB+fAQD1h5BRHdaCJ2vTarMGbL95lcZqdw1l4NRLgHe68csH+QEAlo32t2D26d9r
MEgGvtAeHgPDoATxQk20c1PVHgDe4wE=
=lbN1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.19-rc4
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
* tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel RM500K module support
USB: serial: option: add Quectel EM05-G modem
USB: serial: pl2303: add support for more HXN (G) types
USB: serial: option: add Telit LE910Cx 0x1250 composition
This merges the movement of the octeon-usb driver out of
drivers/staging/ into drivers/usb.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'staging-octeon' of gitolite.kernel.org:/pub/scm/linux/kernel/git/gregkh/staging:
staging: octeon-usb: move driver out of staging
For code neat purpose, we can use kmemdup to replace
kmalloc + memcpy.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for further HXN (G) type devices (GT variant, GL variant, GS
variant and GR) and document the bcdDevice mapping.
Note that the TA and TB types use the same bcdDevice as some GT and GE
variants, respectively, but that the HX status request can be used to
determine which is which.
Also note that we currently do not distinguish between the various HXN
(G) types in the driver but that this may change eventually (e.g. when
adding GPIO support).
Reported-by: Charles Yeh <charlesyeh522@gmail.com>
Link: https://lore.kernel.org/r/YrF77b9DdeumUAee@hovoldconsulting.com
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20220621152350.145745-5-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220621152350.145745-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220621152350.145745-2-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Octeon usb driver has been in staging for a long time and used in
Ubiquiti routers for a while now.
It's been built and then tested on real hardware with several usb devices
and it is proven to be stable and ready to be moved to its proper place
in the kernel tree.
Move it to drivers/usb/host and adjust its Makefile, Kconfig and defconfig
dependencies.
Many thanks to the developers who made it happen.
Signed-off-by: Artur Bujdoso <artur.bujdoso@gmail.com>
Link: https://lore.kernel.org/r/Yo0HBIlSXOBM+//9@crux
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to simplify handling errors in ci_hdrc_imx_probe()
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220614120522.1469957-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea udc core is capable of reading the current frame index from
hardware. This patch adds the get_frame callback to the driver.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220616194459.2981519-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found the "argument" typo.
It seems that "argument" is more correct than "arguement".
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Link: https://lore.kernel.org/r/20220621064242.GA698757@ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In musb_{save|restore}_context() the expression '&musb->endpoints[i]' just
cannot be NULL, so the checks have no sense at all -- after dropping them,
the local variables 'hw_ep' are no longer necessary, so drop them as well.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/3f8f60d9-f1b5-6b2c-1222-39b156151a22@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usbhs_rza1_hardware_init(), of_find_node_by_name() will return
a node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220618023205.4056548-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ohci_hcd_ppc_of_probe(), of_find_compatible_node() will return
a node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220617034637.4003115-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loosen the typec_mux_match() requirements so that searches where an
alt mode is not specified, but the target mux device lists the
"mode-switch" property, return a success.
This is helpful in Type C port drivers which would like to get a pointer
to the mux switch associated with a Type C port, but don't want to
specify a particular alt mode.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220615172129.1314056-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3 is wakeup capable, keep the power domain always ON so that
wakeup from system suspend can be supported. Otherwise, keep the
power domain ON only during runtime suspend to support wakeup from
runtime suspend.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-6-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DP/DM line interrupts based on the USB2 device attached to
the root hub port. When HS/FS device is connected, configure the DP line
as falling edge to detect both disconnect and remote wakeup scenarios. When
LS device is connected, configure DM line as falling edge to detect both
disconnect and remote wakeup. When no device is connected, configure both
DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-5-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check wakeup-source property for dwc3 core node to set the
wakeup capability. Drop the device_init_wakeup call from
runtime suspend and resume.
If the dwc3 is wakeup capable, don't power down the USB PHY(s).
The glue drivers are expected to take care of configuring the
additional wakeup settings if needed based on the dwc3 wakeup
capability status. In some SOC designs, powering off the PHY is
resulting in higher leakage, so this patch save power on such boards.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-3-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys IP DWC_usb32 and DWC_usb31 version 1.90a and above deprecated
GCTL.CORESOFTRESET. The DRD mode switching flow is updated to remove the
GCTL soft reset. Add version checks to prevent using deprecated setting
in mode switching flow.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9df529fde6e55f5508321b6bc26e92848044ef2b.1655338967.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
This was found by coccicheck:
./drivers/usb/gadget/udc/aspeed_udc.c:1546:2-9: line 1546 is redundant because platform_get_irq() already prints an error.
Acked-by: Neal Liu <neal_liu@aspeedtech.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220616090410.128483-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a couple of spelling mistakes, one in a dev_warn message
and another in a SETUP_DBG message. Fix these and remove an extraneous
white space too.
Acked-by: Neal Liu <neal_liu@aspeedtech.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220615073518.192827-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "chunk >= 0" condition does not work because count is a u32.
Also, really we shouldn't enter the loop when "chunk" is zero.
Once that condition is fixed then there is no need for the "last"
variable. I reversed the "if (chunk <= ep->chunk_max)" as well.
The new loop is much simpler.
Fixes: 055276c132 ("usb: gadget: add Aspeed ast2600 udc driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yq2SvM2bbrtSd1H9@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel SoC PMIC is a generic name for all PMICs that are used
on Intel platforms. In particular, INTEL_SOC_PMIC kernel configuration
option refers to Crystal Cove PMIC, which has never been a part
of any Intel Broxton hardware. Drop wrong dependency from Kconfig.
Note, the correct dependency is satisfied via ACPI PMIC OpRegion driver,
which the Type-C depends on.
Fixes: d2061f9cc3 ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620104316.57592-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A panic can occur if the endpoint becomes disabled and the
uvcg_video_pump adds the request back to the req_free list after it has
already been queued to the endpoint. The endpoint complete will add the
request back to the req_free list. Invalidate the local request handle
once it's been queued.
<6>[ 246.796704][T13726] configfs-gadget gadget: uvc: uvc_function_set_alt(1, 0)
<3>[ 246.797078][ T26] list_add double add: new=ffffff878bee5c40, prev=ffffff878bee5c40, next=ffffff878b0f0a90.
<6>[ 246.797213][ T26] ------------[ cut here ]------------
<2>[ 246.797224][ T26] kernel BUG at lib/list_debug.c:31!
<6>[ 246.807073][ T26] Call trace:
<6>[ 246.807180][ T26] uvcg_video_pump+0x364/0x38c
<6>[ 246.807366][ T26] process_one_work+0x2a4/0x544
<6>[ 246.807394][ T26] worker_thread+0x350/0x784
<6>[ 246.807442][ T26] kthread+0x2ac/0x320
Fixes: f9897ec0f6 ("usb: gadget: uvc: only pump video data if necessary")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220617163154.16621-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a report for a separate bug (which has already been fixed by commit
5f0b5f4d50 "usb: gadget: fix race when gadget driver register via
ioctl") in the raw-gadget driver, the syzbot console log included
error messages caused by attempted registration of a new driver with
the same name as an existing driver:
> kobject_add_internal failed for raw-gadget with -EEXIST, don't try to register things with the same name in the same directory.
> UDC core: USB Raw Gadget: driver registration failed: -17
> misc raw-gadget: fail, usb_gadget_register_driver returned -17
These errors arise because raw_gadget.c registers a separate UDC
driver for each of the UDC instances it creates, but these drivers all
have the same name: "raw-gadget". Until recently this wasn't a
problem, but when the "gadget" bus was added and UDC drivers were
registered on this bus, it became possible for name conflicts to cause
the registrations to fail. The reason is simply that the bus code in
the driver core uses the driver name as a sysfs directory name (e.g.,
/sys/bus/gadget/drivers/raw-gadget/), and you can't create two
directories with the same pathname.
To fix this problem, the driver names used by raw-gadget are made
distinct by appending a unique ID number: "raw-gadget.N", with a
different value of N for each driver instance. And to avoid the
proliferation of error handling code in the raw_ioctl_init() routine,
the error return paths are refactored into the common pattern (goto
statements leading to cleanup code at the end of the routine).
Link: https://lore.kernel.org/all/0000000000008c664105dffae2eb@google.com/
Fixes: fc274c1e99 "USB: gadget: Add a new bus for gadgets"
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+02b16343704b3af1667e@syzkaller.appspotmail.com
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YqdG32w+3h8c1s7z@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of walking the list of children of an ACPI device directly
in order to find the child matching a given bus address, use
acpi_find_child_by_adr() for this purpose.
Also notice that if acpi_find_child_by_adr() doesn't find a matching
child, acpi_find_child_device() will not find it too, so directly
replace usb_acpi_find_port() in usb_acpi_get_companion_for_port() with
acpi_find_child_by_adr() and drop it entirely.
Apart from simplifying the code, this will help to eliminate the
children list head from struct acpi_device as it is redundant and it
is used in questionable ways in some places (in particular, locking is
needed for walking the list pointed to it safely, but it is often
missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmKvgdceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0qMH/RnVz4BvYXVWWc1t
+4NT9N20pNzrByzUxSBsrLfL5BNIt9fNjrS0WLs4HlzExbiixvKIBHPkDZoCo1gQ
wxoqpJf2BMxmdXH46/wWdSszbdPk33eLM/MfYE2QfnmtYsDSLZQMzOUAcdh6qD53
ty9br3IM/g4ixCwxKRt3NNixjin4wTTxR5ZD2E5k0JAaT+4FW5llRvq92dA1UOq7
JeGRLkc2l0211MFLo0vtuPOyWMIQL8t98rKTzevwoVY7R9I/0uUJCbkU7mb9wMUY
yKYlTN/4ZikTTSxa8NpQsXHqTyOHaKmS5F6oE4sw9VurHI2u3Jmxy9j9AwO1Pn8C
JUizMCk=
=qqcu
-----END PGP SIGNATURE-----
Merge v5.19-rc3 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aspeed udc is compliant with USB2.0, supports USB High Speed
and Full Speed, backward compatible with USB1.1.
Supports independent DMA channel for each generic endpoint.
Supports 32/256 stages descriptor mode for all generic endpoints.
This driver supports full functionality including single/multiple
stages descriptor mode, and exposes 1 UDC gadget driver.
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20220523030134.2977116-2-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host needs to tell the device the exit latencies using the SET_SEL
request before device initiated link powermanagement can be enabled.
The exit latency values do not change after enumeration, it's enough
to set them once. So do like Windows 10 and issue the SET_SEL request
once just before setting the configuration.
This is also the sequence described in USB 3.2 specs "9.1.2 Bus
enumeration". SET_SEL is issued once before the Set Configuration
request, and won't be cleared by the Set Configuration,
Set Interface or ClearFeature (STALL) requests.
Only warm reset, hot reset, set Address 0 clears the exit latencies.
See USB 3.2 section 9.4.14 Table 9-10 Device parameters and events
Add udev->lpm_devinit_allow, and set it if SET_SEL was successful.
If not set, then don't try to enable device initiated LPM
We used to issue a SET_SEL request every time lpm is enabled for either
U1 or U2 link states, meaning a SET_SEL was issued twice after every
Set Configuration and Set Interface requests, easily accumulating to
over 15 SET_SEL requets during a USB3 webcam enumeration.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220506161807.3369439-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register both the port and partner USB Power Delivery
Capabilities so they are exposed to the user space.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the USB Type-C Connector Class devices are protected, so
the drivers can not directly access them. This will adds a
few helpers that can be used to link the ports and partners
to the correct USB Power Delivery objects.
For ports a new optional sysfs attribute file is also added
that can be used to select the USB Power Delivery
capabilities that the port will advertise to the partner.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a small device class for USB Power Delivery.
The idea with it is that we do not mix any more USB Power
Delivery information into the USB Type-C connectors only.
This separation will make it possible to register USB Power
Delivery devices also from other places, for example from
USB Type-C Bridges (see USB Type-C Bridge Specification).
The device class will not always deal with only the messages
and objects that were negotiated with the partner, but
instead messages and objects that can be used in the
negotiation. That allows the USB PD devices to be shared and
reconfigured. The ports can decide which objects are to be
advertised to the partner before the contract is negotiated.
It is also possible to allow the user space to make that
decision if needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases the port of an hub needs to be disabled or switched off
and on again. E.g. when the connected device needs to be re-enumerated.
Or it needs to be explicitly disabled while the rest of the usb tree
stays working.
For this purpose this patch adds an sysfs switch to enable/disable the
port on any hub. In the case the hub is supporting power switching, the
power line will be disabled to the connected device.
When the port gets disabled, the associated device gets disconnected and
removed from the logical usb tree. No further device will be enumerated
on that port until the port gets enabled again.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220607114522.3359148-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ffs_epfile_io(), when read/write data in blocking mode, it will wait
the completion in interruptible mode, if task receive a signal, it will
terminate the wait, at same time, if function unbind occurs,
ffs_func_unbind() will kfree all eps, ffs_epfile_io() still try to
dequeue request by dereferencing ep which may become invalid.
Fix it by add ep spinlock and will not dereference ep if it is not valid.
Cc: <stable@vger.kernel.org> # 5.15
Reported-by: Michael Wu <michael@allwinnertech.com>
Tested-by: Michael Wu <michael@allwinnertech.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1654863478-26228-3-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a task read/write data in blocking mode, it will wait the completion
in ffs_epfile_io(), if function unbind occurs, ffs_func_unbind() will
kfree ffs ep, once the task wake up, it still dereference the ffs ep to
obtain the request status.
Fix it by moving the request status to io_data which is stack-safe.
Cc: <stable@vger.kernel.org> # 5.15
Reported-by: Michael Wu <michael@allwinnertech.com>
Tested-by: Michael Wu <michael@allwinnertech.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1654863478-26228-2-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the re-init path xhci_resume() passes 'hcd->primary_hcd' to hci_init(),
however this field isn't initialized by __usb_create_hcd() for a HCD
without secondary controller.
xhci_resume() is called once per xHC device, not per hcd, so the extra
checking for primary hcd can be removed.
Fixes: e0fe986972 ("usb: host: xhci-plat: prepare operation w/o shared hcd")
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220610115338.863152-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the AMD platforms have Cypress CCGX PD controller connected
to system I2C i.e designware I2C controller. Added support to enumerate
the CCGX client by adding ACPI ID to the firmware.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20220526063305.3144352-3-Sanket.Goswami@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation supports only Level trigger with ACTIVE HIGH,
which is overriding level and polarity set by the ACPI table, hence
implement the common utility function to manage irq requests.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20220526063305.3144352-2-Sanket.Goswami@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register gadget irq to avoid the interrupt handler is occurred
or scheduled during the unbind flow, may happen when do android
function switch stress test.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220609074233.15532-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In musb_remove() cancel_delayed_work_sync(&musb->irq_work)
is called which flush the irq_work work queue.
After cancel delayed work, musb_remove() call
musb_gadget_cleanup->usb_del_gadget_udc->usb_del_gadget
->usb_gadget_remove_driver->usb_gadget_udc_stop->udc
->gadget->ops->udc_stop(udc->gadget);
Where musb_gadget_stop() call "schedule_delayed_work(&musb->irq_work, 0)”
which is already cancel/flush.
So remove the schedule_delayed_work(&musb->irq_work, 0);
from musb_gadget_stop function.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/YqDnxkWZV2KfZh5q@Sauravs-MacBook-Air.local
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Likewise to the uvcvideo hostside driver, this patch is changing the
usb_request message of an non zero completion handler call from dev_info
to dev_warn.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220529223848.105914-4-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current limitation of possible number of requests being handled is
dependent on the gadget speed. It makes more sense to depend on the
typical frame size when calculating the number of requests. This patch
is changing this and is using the previous limits as boundaries for
reasonable minimum and maximum number of requests.
For a 1080p jpeg encoded video stream with a maximum imagesize of
e.g. 800kB with a maxburst of 8 and an multiplier of 1 the resulting
number of requests is calculated to 49.
800768 1
nreqs = ------ * -------------- ~= 49
2 (1024 * 8 * 1)
Tested-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220529223848.105914-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support controller reset via a reset-controller usually in infracfg,
it's different with the software reset by IPPC which only used to reset MAC,
and it will also reset IPPC meanwhile.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220523090449.14430-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support controller reset via a reset-controller usually in infracfg,
it's different with the software reset by IPPC which only used to reset MAC,
and it will also reset IPPC meanwhile.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220523090449.14430-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-92-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-52-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function tegra_xusb_powerdomain_init(),
dev_pm_domain_attach_by_name() may return NULL in some cases,
so IS_ERR() doesn't meet the requirements. Thus fix it.
Fixes: 6494a9ad86 ("usb: xhci: tegra: Add genpd support")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20220524121404.18376-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_domain_attach_by_name() may return NULL in some cases,
so IS_ERR() doesn't meet the requirements. Thus fix it.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20220525135332.23144-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the VBUS/ID detection interrupts are disabled during system
suspend. So the USB cable connect/disconnect event can't wakeup the
system from low power mode. To allow this, we keep these interrupts
enabled and configure them as wakeup capable. This behavior can be
controlled through device wakeup source policy by the user space.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1653634146-12215-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code does:
spin_unlock_irq(&udc->ud.lock);
spin_unlock_irqrestore(&udc->lock, flags);
which does not make sense. In theory, the first unlock could enable
IRQs and then the second _irqrestore could disable them again. There
would be a brief momemt where IRQs were enabled improperly.
In real life, however, this function is always called with IRQs enabled
and the bug does not affect runtime.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yo4hVWcZNYzKEkIQ@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It generally doesn't make sense to use _irq() and _irqsave() in the same
function because either some of the callers have disabled IRQs or they
haven't. In this case, the v_recv_cmd_submit() appears to always be
called with IRQs enabled so the code works fine. That means I could
convert it to either _irq() or _irqsave() but I chose to use _irqsave()
because it's more conservative and easier to review.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yo4gqLPtHO6XKMLn@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 57303488cd ("usb: dwc3: adapt dwc3 core to use Generic PHY
Framework") added if statements that check 'ret == -ENOSYS || ret ==
-ENODEV', but the function phy_get() which is called by devm_phy_get()
returns the phy driver or -ENODEV if the phy driver was not found. So,
remove the check of -ENOSYS in the if statements.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/HK0PR01MB2801E19D4FE569545BB7592DF8A19@HK0PR01MB2801.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Linux is running under OP-TEE, the SFR is set as secured and thus
the AT91_OHCIICR_USB_SUSPEND register isn't accessible. Add a SMC to
do the appropriate call to suspend the controller.
The SMC id is fetched from the device-tree property
"microchip,suspend-smc-id". if present, then the syscon regmap is not
used to enter suspend and a SMC is issued.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220607133454.727063-1-clement.leger@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 73108aa90c ("USB: ohci-nxp: Use isp1301 driver")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220603141231.979-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 796bcae736 ("USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220602110849.58549-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC(e.g NXP imx8MQ) may have a wrong default power down scale
setting so need init it to be the correct value, the power down
scale setting description in DWC3 databook:
Power Down Scale (PwrDnScale)
The USB3 suspend_clk input replaces pipe3_rx_pclk as a clock source to
a small part of the USB3 core that operates when the SS PHY is in its
lowest power (P3) state, and therefore does not provide a clock.
The Power Down Scale field specifies how many suspend_clk periods fit
into a 16 kHz clock period. When performing the division, round up the
remainder.
For example, when using an 8-bit/16-bit/32-bit PHY and 25-MHz Suspend
clock,
Power Down Scale = 25000 kHz/16 kHz = 13'd1563 (rounder up)
So use the suspend clock rate to calculate it.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1654568404-3461-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KFENCE: use-after-free read in __list_del_entry_valid+0x10/0xac
cdns3_wa2_remove_old_request()
{
...
kfree(priv_req->request.buf);
cdns3_gadget_ep_free_request(&priv_ep->endpoint, &priv_req->request);
list_del_init(&priv_req->list);
^^^ use after free
...
}
cdns3_gadget_ep_free_request() free the space pointed by priv_req,
but priv_req is used in the following list_del_init().
This patch move list_del_init() before cdns3_gadget_ep_free_request().
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Faqiang Zhu <faqiang.zhu@nxp.com>
Link: https://lore.kernel.org/r/20220608190430.2814358-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UVC gadget driver historically uses the
/* Comment
* style
*/
for multi-line block comments, which is frowned upon. Patches for the
driver are required to use the more standard
/*
* Comment
* style
*/
style. This result in inconsistencies. Fix it by converting all
remaining instances of the old style.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220608174918.14656-1-laurent.pinchart@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today's linux-next merge of the extcon tree got a conflict in:
drivers/usb/dwc3/drd.c
between commit:
0f01017191 ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
from the usb tree and commit:
88490c7f43c4 ("extcon: Fix extcon_get_extcon_dev() error handling")
from the extcon tree.
I fixed it up (the former moved the code modified by the latter, so I
used the former version of this files and added the following merge fix
patch) and can carry the fix as necessary.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220426152739.62f6836e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ZLP occurs in bulk transmission, currently cdnsp will set last_trb
for the last two TRBs, it will trigger an error "ERROR Transfer event TRB
DMA ptr not part of current TD ...".
Fixes: e913aada06 ("usb: cdnsp: Fixed issue with ZLP")
Cc: stable <stable@kernel.org>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Jing Leng <jleng@ambarella.com>
Link: https://lore.kernel.org/r/20220609021134.1606-1-3090101217@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In systemd systems setting a fixed MAC address through
the "dev_addr" module argument fails systematically.
When checking the MAC address after the interface is created
it always has the same but different MAC address to the one
supplied as argument.
This is partially caused by systemd which by default will
set an internally generated permanent MAC address for interfaces
that are marked as having a randomly generated address.
Commit 890d5b4090 ("usb: gadget: u_ether: fix race in
setting MAC address in setup phase") didn't take into account
the fact that the interface must be marked as having a set
MAC address when it's set as module argument.
Fixed by marking the interface with NET_ADDR_SET when
the "dev_addr" module argument is supplied.
Fixes: 890d5b4090 ("usb: gadget: u_ether: fix race in setting MAC address in setup phase")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20220603153459.32722-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
Fixes: 24a28e4283 ("USB: gadget driver for LPC32xx")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220603140246.64529-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when platform_get_resource()
fails to prevent memory leak.
goto error2 label instead error1 to fix this.
Fixes: 856e6e8e0f ("usb: dwc2: check return value after calling platform_get_resource()")
Cc: stable <stable@kernel.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220530085413.44068-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 582ab24e09 ("usb: dwc3: pci: Set "linux,phy_charger_detect"
property on some Bay Trail boards") added a new swnode similar to the
existing ones for boards where the PHY handles charger detection.
Unfortunately, the "linux,sysdev_is_parent" property got lost in the
merge conflict resolution of commit ca9400ef7f ("Merge 5.17-rc6 into
usb-next"). Now dwc3_pci_intel_phy_charger_detect_properties is the
only swnode in dwc3-pci that is missing "linux,sysdev_is_parent".
It does not seem to cause any obvious functional issues, but it's
certainly unintended so restore the line to make the properties
consistent again.
Fixes: ca9400ef7f ("Merge 5.17-rc6 into usb-next")
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220528170913.9240-1-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic to assign the max packet limit for IN endpoints attempts
to take the default HW value and apply the optimal endpoint settings based
on it. However, if the default value reports a TxFIFO size large enough
for only one max packet, it will divide the value and assign a smaller ep
max packet limit.
For example, if the default TxFIFO size fits 1024B, current logic will
assign 1024/3 = 341B to ep max packet size. If function drivers attempt to
request for an endpoint with a wMaxPacketSize of 1024B (SS BULK max packet
size) then it will fail, as the gadget is unable to find an endpoint which
can fit the requested size.
Functionally, if the TxFIFO has enough space to fit one max packet, it will
be sufficient, at least when initializing the endpoints.
Fixes: d94ea53198 ("usb: dwc3: gadget: Properly set maxpacket limit")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220523213948.22142-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed
change that goes a long way to making things simpler for all
of the different arches
- tty documentation cleanups and movements to their own place in
the documentation tree
- old tty driver cleanups and fixes from Jiri to bring some
existing drivers into the modern world
- RS485 cleanups and unifications to make it easier for
individual drivers to support this mode instead of having to
duplicate logic in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpndTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykFegCgizjLDyOepr72zMDWWdp0bBTekz8AoMWODfJY
vB8/kzu329DImJMFB8ET
=rmv0
-----END PGP SIGNATURE-----
Merge tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
- Add Meteor Lake ACPI IDs for DPTF devices (Sumeet Pawnikar).
- Rearrange find_child_checks() to simplify code (Rafael Wysocki).
- Use memremap() to map the UCSI mailbox that is always in main memory
and drop acpi_release_memory() that has no more users (Heikki
Krogerus, Dan Carpenter).
- Make max_cstate/nocst/bm_check_disable processor module parameters
visible in sysfs (Yajun Deng).
- Fix typo in the CPPC driver (Julia Lawall).
- Make the ACPI battery driver show the "not-charging" status by
default unless "charging" or "full" is directly indicated (Werner
Sembach).
- Improve the PM notifier in the ACPI backlight driver (Zhang Rui).
- Clean up some white space in the ACPI code (Ian Cowan).
-----BEGIN PGP SIGNATURE-----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=rROP
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add some new device IDs, update a few drivers (processor,
battery, backlight) and clean up code in a few places.
Specifics:
- Add Meteor Lake ACPI IDs for DPTF devices (Sumeet Pawnikar)
- Rearrange find_child_checks() to simplify code (Rafael Wysocki)
- Use memremap() to map the UCSI mailbox that is always in main
memory and drop acpi_release_memory() that has no more users
(Heikki Krogerus, Dan Carpenter)
- Make max_cstate/nocst/bm_check_disable processor module parameters
visible in sysfs (Yajun Deng)
- Fix typo in the CPPC driver (Julia Lawall)
- Make the ACPI battery driver show the "not-charging" status by
default unless "charging" or "full" is directly indicated (Werner
Sembach)
- Improve the PM notifier in the ACPI backlight driver (Zhang Rui)
- Clean up some white space in the ACPI code (Ian Cowan)"
* tag 'acpi-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
usb: typec: ucsi: acpi: fix a NULL vs IS_ERR() check in probe
ACPI: DPTF: Support Meteor Lake
ACPI: CPPC: fix typo in comment
ACPI: video: improve PM notifer callback
ACPI: clean up white space in a few places for consistency
ACPI: glue: Rearrange find_child_checks()
ACPI: processor: idle: Expose max_cstate/nocst/bm_check_disable read-only in sysfs
ACPI: battery: Make "not-charging" the default on no charging or full info
ACPI: OSL: Remove the helper for deactivating memory region
usb: typec: ucsi: acpi: Map the mailbox with memremap()
Merge general ACPI cleanups and processor support updates for 5.19-rc1:
- Rearrange find_child_checks() to simplify code (Rafael Wysocki).
- Use memremap() to map the UCSI mailbox that is always in main memory
and drop acpi_release_memory() that has no more users (Heikki
Krogerus, Dan Carpenter).
- Make max_cstate/nocst/bm_check_disable processor module parameters
visible in sysfs (Yajun Deng).
- Fix typo in the CPPC driver (Julia Lawall).
* acpi-glue:
ACPI: glue: Rearrange find_child_checks()
* acpi-osl:
usb: typec: ucsi: acpi: fix a NULL vs IS_ERR() check in probe
ACPI: OSL: Remove the helper for deactivating memory region
usb: typec: ucsi: acpi: Map the mailbox with memremap()
* acpi-processor:
ACPI: processor: idle: Expose max_cstate/nocst/bm_check_disable read-only in sysfs
* acpi-cppc:
ACPI: CPPC: fix typo in comment
The devm_memremap() function never returns NULL. It returns error
pointers.
Fixes: cdc3d2abf4 ("usb: typec: ucsi: acpi: Map the mailbox with memremap()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which
is the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of the
mach/*.h headers to allow the platform to be part of a generic ARMv4/v5
multiplatform kernel. The last bit that enables this support is still
missing here while we wait for some last dependencies to make it into
the mainline kernel through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets completed
here along with a few additional cleanup. At the same time, the s3c24xx
and s3c64xx are now deprecated and expected to get removed in the future.
The PXA and OMAP1 bits are in a separate branch because of dependencies.
Once both branches are merged, only the three Intel StrongARM platforms
(RiscPC, Footbridge/NetWinder and StrongARM1100) need separate kernels,
and there are no plans to include these.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmKOP3sACgkQmmx57+YA
GNk+DhAAmrPNuS8JDlCRPa76Nd9PC9aitnnEGYytQ6bgwexKd3qdvP7gdUtr7jlV
8k4KiGnnZZjEGd4i5cAVhSCyBbCt4oPKhato62KneEsO19xLsVmmTpQg1LPK75do
mHYKpc+6932Lp6WrtI1F75id0phx684tpZp9P4ggXwMwgYkagq9rcO+mGUNZWDc8
D9SdAmoObtSCoBCYYbq2VhAPA79mSKKVpLGehzd+Gq5cuf/jJQD0u1E00izkdyZc
r/5acQ7PHQlVXqSONYgCpkvDTqmjg9cvVCKeKLpFspV3f6vBVRgV60UGfwhpdPHY
N119KUJtPf81xnLSxsqBFA34LMSerrH72YM5cYupKiiYcTDr+Yw6zrtNR6ktkt/B
F1Tc/QV+A9CGergxljy39G1smEuwKtNiVA//NSlUORCHxgwa5XUB0mQIzNcWARa4
oMDLhBF7ES211CB7Yto2FR6gBQbh2A9HSpjOh6kxdHrRb4FCgoXjPhzBoMxPoSFu
XIzJpMb18K4bI+hKRYddEOK5V0kHt9mzT7ViGT/2+n13IHKIGmKrZxwDH7mohAW9
4GF77gGbQsE9szajkx5EG1t+PWextQeeMyYW05bXO/mbDwA0n7EdjGpBeedvTZw3
6gUWVahfYp9hZWPdxJ4fbGnlbSovCq0y4tj5fbZHPh6AOAtmvWY=
=CTtN
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen
2 device to not fail during enumeration.
Found this bug on own testing
Signed-off-by: Monish Kumar R <monish.kumar.r@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220520130044.17303-1-monish.kumar.r@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.19-rc1, including:
- a workaround for pl2303 devices with unexpected bcdUSB
- a new modem device id
Included is also a printk clean up.
All but the modem-id commit have been in linux-next with no reported
issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYoeFIAAKCRALxc3C7H1l
CIXUAQDnSQdinW//FR1Xaatn0HK/PvgokH4deOOG6OEhSBQZCAD/ZEwOgGEn9Pws
2h1JmHp8B0KOxJox2pyM8MEx8RzoiwE=
=hU3t
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.19-rc1
Here are the USB-serial updates for 5.19-rc1, including:
- a workaround for pl2303 devices with unexpected bcdUSB
- a new modem device id
Included is also a printk clean up.
All but the modem-id commit have been in linux-next with no reported
issues.
* tag 'usb-serial-5.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
USB: serial: ftdi_sio: clean up printk format specifier
CMSPAR is defined by all architectures since commit 6bf08cb246
("[PATCH] Add CMSPAR to termbits.h for powerpc and alpha").
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220513082906.11096-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 controller soft reset is important operation for USB functionality.
In case when it fails, currently there is no failure log. Hence add
error log when core soft reset failed.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1652897572-14461-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Example call stack:
Thread#1:
dwc3_thread_interrupt()
spin_lock
-> dwc3_process_event_buf()
-> dwc3_process_event_entry()
-> dwc3_endpoint_interrupt()
-> dwc3_gadget_endpoint_trbs_complete()
-> dwc3_gadget_ep_cleanup_completed_requests()
...
-> dwc3_giveback()
spin_unlock
Thread#2 executes
Thread#2:
configfs_composite_disconnect()
-> __composite_disconnect()
-> ffs_func_disable()
-> ffs_func_set_alt()
-> ffs_func_eps_disable()
-> usb_ep_disable()
wait for dwc3 spin_lock
Thread#1 released lock
clear endpoint.desc
Fixes: 2628844812 ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have USB compositions which may require multiple endpoints.
To get better performance, need bigger CDNS3_EP_BUF_SIZE.
But bigger CDNS3_EP_BUF_SIZE may exceed total hardware FIFO size when
multiple endpoints.
By introducing the check_config() callback, calculate CDNS3_EP_BUF_SIZE.
Move CDNS3_EP_BUF_SIZE into cnds3_device: ep_buf_size
Combine CDNS3_EP_ISO_SS_BURST and CDNS3_EP_ISO_HS_MULT into
cnds3_device:ep_iso_burst
Using a simple algorithm to calculate ep_buf_size.
ep_buf_size = ep_iso_burst = (onchip_buffers - 2k) / (number of IN EP +
1).
Test at 8qxp:
Gadget ep_buf_size
RNDIS: 5
RNDIS+ACM: 3
Mass Storage + NCM + ACM 2
Previous CDNS3_EP_BUF_SIZE is 4, RNDIS + ACM will be failure because
exceed FIFO memory.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220509164055.1815081-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the databook ep0 should be in setup phase during reset.
If host issues reset between control transfers, ep0 will be in an
invalid state. Fix this by issuing stall and restart on ep0 if it
is not in setup phase.
Also SW needs to complete pending control transfer and setup core for
next setup stage as per data book. Hence check ep0 state during reset
interrupt handling and make sure active transfers on ep0 out/in
endpoint are stopped by queuing ENDXFER command for that endpoint and
restart ep0 out again to receive next setup packet.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1651693001-29891-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
initcall_debug shows that OHCI controllers take ~60ms to probe on
Rockchip RK3399 systems:
probe of fe3a0000.usb returned 1 after 58941 usecs
A few of these can add up to waste non-trivial amounts of time at boot.
These host controllers don't provide resources to other drivers, so
this shouldn't contribute to exposing race conditions.
Chrome OS kernels have carried this patch on some systems for a while
without issues. Similar patches have been merged for a variety of (e)MMC
host controllers for similar reasons.
[Brian: rewrote commit message, refreshed, but retained dtor's original
authorship ]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220518150150.1.Ie8ea0e945a9c15066237014be219eed60066d493@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running the driver through kasan gives an interesting splat:
BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c
Read of size 20 at addr f1db2e64 by task swapper/0/1
(...)
isp1760_register from isp1760_plat_probe+0x1d8/0x220
(...)
This happens because the loop reading the regmap fields for the
different ISP1760 variants look like this:
for (i = 0; i < HC_FIELD_MAX; i++) { ... }
Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long.
However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[],
isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are
dynamically sized during compilation.
Fix this by putting an empty assignment to the [HC_FIELD_MAX]
and [DC_FIELD_MAX] array member at the end of each array.
This will make the array one member longer than it needs to be,
but avoids the risk of overwriting whatever is inside
[HC_FIELD_MAX - 1] and is simple and intuitive to read. Also
add comments explaining what is going on.
Fixes: 1da9e1c068 ("usb: isp1760: move to regmap for register access")
Cc: stable@vger.kernel.org
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220516091424.391209-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support for xHCI controllers with only one roothub, and the code
to defer primary roothub registation until second roothub got merged
to usb-next for 5.19 at the same time.
commit 873f323618 ("xhci: prepare for operation w/o shared hcd")
commit b7a4f9b5d0 ("xhci: Set HCD flag to defer primary roothub
registration")
These got merged in such a way that the flag to defer primary roothub
registration is set even for xHC controllers with just one roothub.
Fix this by setting the defer flag in a codepath taken only if we have
two roothubs
Fixes: 873f323618 ("xhci: prepare for operation w/o shared hcd")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220516094850.19788-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a private macro for an invalid grant reference use
the common one.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Here are some new device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYn31fQAKCRALxc3C7H1l
CKb9AQCj2VXCCMKXtOmKPs4p5KKUjIHHdHLxqz2gBb8XEdGDhAEApKZiHLDJh+77
bLsmDn6DN6gCqn9CppXRYjDM+W4L2wI=
=gxjM
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial
Johan writes:
USB-serial fixes for 5.18-rc7
Here are some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM7590
USB: serial: option: add Fibocom MA510 modem
USB: serial: option: add Fibocom L610 modem
USB: serial: pl2303: add device id for HP LM930 Display
The bandwidth budget table is introduced to trace ideal bandwidth used
by each INT/ISOC endpoint, but in fact the endpoint may consume more
bandwidth and cause data transfer error, so it's better to leave some
margin. Obviously it's difficult to find the best margin for all cases,
instead take use of the worst-case scenario.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220512064931.31670-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the scheduler allocates the optimal bandwidth for FS ISOC endpoints,
this may be not enough actually and causes data transfer error, so come up
with an estimate that is no less than the worst case bandwidth used for
any one mframe, but may be an over-estimate.
Fixes: 451d391258 ("usb: xhci-mtk: update fs bus bandwidth by bw_budget_table")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220512064931.31670-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_gadget_register_driver can be called multi time by to
threads via USB_RAW_IOCTL_RUN ioctl syscall, which will lead
to multiple registrations.
Call trace:
driver_register+0x220/0x3a0 drivers/base/driver.c:171
usb_gadget_register_driver_owner+0xfb/0x1e0
drivers/usb/gadget/udc/core.c:1546
raw_ioctl_run drivers/usb/gadget/legacy/raw_gadget.c:513 [inline]
raw_ioctl+0x1883/0x2730 drivers/usb/gadget/legacy/raw_gadget.c:1220
ioctl USB_RAW_IOCTL_RUN
This routine allows two processes to register the same driver instance
via ioctl syscall. which lead to a race condition.
Please refer to the following scenarios.
T1 T2
------------------------------------------------------------------
usb_gadget_register_driver_owner
driver_register driver_register
driver_find driver_find
bus_add_driver bus_add_driver
priv alloced <context switch>
drv->p = priv;
<schedule out>
kobject_init_and_add // refcount = 1;
//couldn't find an available UDC or it's busy
<context switch>
priv alloced
drv->priv = priv;
kobject_init_and_add
---> refcount = 1 <------
// register success
<context switch>
===================== another ioctl/process ======================
driver_register
driver_find
k = kset_find_obj()
---> refcount = 2 <------
<context out>
driver_unregister
// drv->p become T2's priv
---> refcount = 1 <------
<context switch>
kobject_put(k)
---> refcount = 0 <------
return priv->driver;
--------UAF here----------
There will be UAF in this scenario.
We can fix it by adding a new STATE_DEV_REGISTERING device state to
avoid double register.
Reported-by: syzbot+dc7c3ca638e773db07f6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000e66c2805de55b15a@google.com/
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Schspa Shi <schspa@gmail.com>
Link: https://lore.kernel.org/r/20220508150247.38204-1-schspa@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alder Lake N TCSS xHCI needs to be runtime suspended whenever possible
to allow the TCSS hardware block to enter D3 and thus save energy
Cc: stable@kernel.org
Suggested-by: Gopal Vamshi Krishna <vamshi.krishna.gopal@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_RESET_EP_QUIRK was added in 2009 to support prototype xHC
hardware from Fresco Logic that needed an additional configure endpoint
command after a reset endpoint.
That hardware should not have made it to the market.
Now, 13 years later its about time we get rid of it.
quirk was added in commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco
Logic xHCI hardware.")
Print a debug message about the removed quirk if against all odds we run
into this controller.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't enable U1 or U2 Link powermanagenet (LPM) states for USB3
devices connected to tier 2 or further hubs.
For unknown reasons we previously only prevented U1.
Be consistent, and prevent both U1/U2 states if tier policy doesn't
allow LPM.
Also check the tier policy a bit earlier, and return if U1/U2 is
not allowed. This avoids unnecessary xhci MEL commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Activate the just added extension for xhci-plat and omit the shared
hcd if either of the root hubs has no ports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci-plat for the following scenario
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik