Add the product IDs for the USB-to-Serial devices FT2233HP, FT2232HP,
FT4233HP, FT4232HP, FT233HP, FT232HP, and FT4232HA.
Also include BCD values so that the chip type can be determined.
Signed-off-by: Amireddy mallikarjuna reddy <mallikarjuna.reddy@ftdichip.com>
Link: https://lore.kernel.org/r/ac28f2c5eba23a645b3b9299c224f2755a233eef.1658385786.git.mallikarjuna.reddy@ftdichip.com
[ johan: rebase on type-handling rework, drop "Q" from automotive type
name ]
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for adding further Hi-Speed types, assume the device type
is Hi-Speed unless it's an explicitly listed legacy type when
determining divisors.
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for adding further Hi-Speed types, assume a 120 MHz clock
and set the channel index by default and instead override these values
as needed for legacy types.
Signed-off-by: Johan Hovold <johan@kernel.org>
Multi-channel devices need to encode the channel selector in their
control requests and newer single-channel chip types use the same
request format.
Set the channel index also for these single-channel types so that the
index can be used to determine the baudrate request format instead of
listing types explicitly.
Note that FT232H and FTX accept either 0 or 1 as selector for their
single channel, presumably for backward compatibility reasons.
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver exposes two attributes for all chip types but FT232A, which
doesn't have a configurable latency timer, and SIO, which (probably)
doesn't support the event-char mechanism either.
Explicitly test for the exceptions rather than list each and every
supported device type in the attribute helpers.
Signed-off-by: Johan Hovold <johan@kernel.org>
All chip types but the original SIO (FT8U100AX) return a two-byte modem
status and there's no need to explicitly list every other type in the
handler.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up and tighten the device-type detection, which is based on
bcdDevice.
Don't make assumptions about unknown (future) types (currently assumed
to be either FT2232C or FT-X depending on bNumInterfaces) and instead
log an error and refuse to bind so that we can add proper support when
needed.
Note that the bcdDevice values have been provided by FTDI.
Signed-off-by: Johan Hovold <johan@kernel.org>
Multi-channel devices require a channel selector to be included in
control requests.
Replace "interface" with the less ambiguous "channel", which is the
terminology used for newer devices, in the corresponding defines and
variables.
Signed-off-by: Johan Hovold <johan@kernel.org>
Shorten the chip type enum and string representation for A, B and R chip
types so that they don't include the IC package type in the name.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the chip type enum by dropping the explicit values and moving
the definition to the implementation to make it easier to add further
types.
Signed-off-by: Johan Hovold <johan@kernel.org>
The 300 bps rate of SIO devices has been mapped to 9600 bps since
2003... Let's fix the regression.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
It removes the need to check the resource data type
separately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Smatch reports the following warning:
drivers/usb/misc/usb3503.c:267 usb3503_probe() warn: 'hub->clk'
from clk_prepare_enable() not released on lines: 240,246,252
Fix this by adding a flag to indicate if hub->clk is prepared or not
and invoke clk_disable_unprepare in the error handling.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220908055903.3550723-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is changing the simple workqueue in the gadget driver to be
allocated as async_wq with a higher priority. The pump worker, that is
filling the usb requests, will have a higher priority and will not be
scheduled away so often while the video stream is handled. This will
lead to fewer streaming underruns.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220907215818.2670097-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6a108a14fa ("kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT")
introduces CONFIG_EXPERT to carry the previous intent of CONFIG_EMBEDDED
and just gives that intent a much better name. That has been clearly a good
and long overdue renaming, and it is clearly an improvement to the kernel
build configuration that has shown to help managing the kernel build
configuration in the last decade.
However, rather than bravely and radically just deleting CONFIG_EMBEDDED,
this commit gives CONFIG_EMBEDDED a new intended semantics, but keeps it
open for future contributors to implement that intended semantics:
A new CONFIG_EMBEDDED option is added that automatically selects
CONFIG_EXPERT when enabled and can be used in the future to isolate
options that should only be considered for embedded systems (RISC
architectures, SLOB, etc).
Since then, this CONFIG_EMBEDDED implicitly had two purposes:
- It can make even more options visible beyond what CONFIG_EXPERT makes
visible. In other words, it may introduce another level of enabling the
visibility of configuration options: always visible, visible with
CONFIG_EXPERT and visible with CONFIG_EMBEDDED.
- Set certain default values of some configurations differently,
following the assumption that configuring a kernel build for an
embedded system generally starts with a different set of default values
compared to kernel builds for all other kind of systems.
Considering the first purpose, at the point in time where CONFIG_EMBEDDED
was renamed to CONFIG_EXPERT, CONFIG_EXPERT already made 130 more options
become visible throughout all different menus for the kernel configuration.
Over the last decade, this has gradually increased, so that currently, with
CONFIG_EXPERT, roughly 170 more options become visible throughout all
different menus for the kernel configuration. In comparison, currently with
CONFIG_EMBEDDED enabled, just seven more options are visible, one in x86,
one in arm, and five for the ChipIdea Highspeed Dual Role Controller.
As the numbers suggest, these two levels of enabling the visibility of even
more configuration options---beyond what CONFIG_EXPERT enables---never
evolved to a good solution in the last decade. In other words, this
additional level of visibility of configuration option with CONFIG_EMBEDDED
compared to CONFIG_EXPERT has since its introduction never become really
valuable. It requires quite some investigation to actually understand what
is additionally visible and it does not differ significantly in complexity
compared to just enabling CONFIG_EXPERT. This CONFIG_EMBEDDED---or any
other config to show more detailed options beyond CONFIG_EXPERT---is
unlikely to be valuable unless somebody puts significant effort in
identifying how such visibility options can be properly split and creating
clear criteria, when some config option is visible with CONFIG_EXPERT and
when some config option is visible only with some further option enabled
beyond CONFIG_EXPERT, such as CONFIG_EMBEDDED attempted to do. For now, it
is much more reasonable to simply make those additional seven options that
visible with CONFIG_EMBEDDED, visible with CONFIG_EXPERT, and then remove
CONFIG_EMBEDDED. If anyone spends significant effort in structuring the
visibility of config options, they may re-introduce suitable new config
options simply as they see fit.
Make the configs for usb chipidea glue drivers visible when CONFIG_EXPERT
is enabled.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220908104337.11940-5-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some DWC3 controllers (e.g. Rockchip SoCs), the DWC3 core
doesn't support 64-bit DMA address width. In this case, this
driver should use the default 32-bit mask. Otherwise, the DWC3
controller will break if it runs on above 4GB physical memory
environment.
This patch reads the DWC_USB3_AWIDTH bits of GHWPARAMS0 which
used for the DMA address width, and only configure 64-bit DMA
mask if the DWC_USB3_AWIDTH is 64.
Fixes: 45d39448b4 ("usb: dwc3: support 64 bit DMA in platform driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20220901083446.3799754-1-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a cable disconnect sequence, if ep0state is not in the SETUP phase,
then nothing will trigger any pending end transfer commands. Force
stopping of any pending SETUP transaction, and move back to the SETUP
phase.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For endxfer commands that do not require an endpoint complete interrupt,
avoid having to wait for the command active bit to clear. This allows for
EP0 events to continue to be handled, which allows for the controller to
complete it. Otherwise, it is known that the endxfer command will fail if
there is a pending SETUP token that needs to be read.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since EP0 transactions need to be completed before the controller halt
sequence is finished, this may take some time depending on the host and the
enabled functions. Increase the controller halt timeout, so that we give
the controller sufficient time to handle EP0 transfers.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the need for making dwc3_gadget_suspend() and dwc3_gadget_resume()
to be called in a spinlock, as dwc3_gadget_run_stop() could potentially
take some time to complete.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DWC3_EP_DELAYED_STOP is set during stop active transfers, then do not
continue attempting to unmap request buffers during dwc3_remove_requests().
This can lead to SMMU faults, as the controller has not stopped the
processing of the TRB. Defer this sequence to the EP0 out start, which
ensures that there are no pending SETUP transactions before issuing the
endxfer.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports the following error: uninitialized symbol 'rlen'
drivers/usb/misc/uss720.c:514 parport_uss720_epp_write_data() error
drivers/usb/misc/uss720.c:575 parport_uss720_ecp_write_data() error
drivers/usb/misc/uss720.c:593 parport_uss720_ecp_read_data() error
drivers/usb/misc/uss720.c:626 parport_uss720_write_compat() error
The root cause is, the failure of usb_bulk_msg leads to the
uninitialized variable rlen in printk function.
Fix this by initializing rlen with zero.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220903100004.2874741-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This from static analysis. The vla_item() takes a size and adds it to
the total. It has a built in integer overflow check so if it encounters
an integer overflow anywhere then it records the total as SIZE_MAX.
However there is an issue here because the "lang_count*(needed_count+1)"
multiplication can overflow. Technically the "lang_count + 1" addition
could overflow too, but that would be detected and is harmless. Fix
both using the new size_add() and size_mul() functions.
Fixes: e6f3862fa1 ("usb: gadget: FunctionFS: Remove VLAIS usage from gadget code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YxDI3lMYomE7WCjn@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DID_TARGET_FAILURE is internal to the SCSI layer. Drivers must not use it
because:
1. It's not propagated upwards, so SG IO/passthrough users will not see an
error and think a command was successful.
2. There is no handling for it in scsi_decide_disposition() so it results
in entering SCSI error handling.
It looks like the driver wanted a hard failure so this swaps it with
DID_BAD_TARGET which gives us that behavior. The error looks like it's for
a case where the target did not support a TMF we wanted to use (maybe not a
bad target but disappointing so close enough).
Link: https://lore.kernel.org/r/20220812010027.8251-4-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop another couple of pointless pr_info() calls, and drop a number of
instances of hcd_name variables that are no longer referenced now that
they are no longer printed to the log at driver registration time.
Fixes: 10174220f5 ("usb: reduce kernel log spam on driver registration")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220905111740.352348-1-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I would like to stop exporting OF-specific gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
fwnode property API.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-5-b29adfb27a6c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I would like to stop exporting OF-specific devm_gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
device property API.
I believe that the only reason the driver, instead of the standard
devm_gpiod_get(), used devm_gpiod_get_from_of_node() is because it
wanted to set up a pretty consumer name for the GPIO, and we now have
a special API for that.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-4-b29adfb27a6c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4), this issue occur when ohci-platform
driver build as a module and the built-in ohci-platform driver will
re probe and re enumerate the devices, so there will be no such problem.
Avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the snapshot image. But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.
According to the commit 'cd1965db054e ("USB: ohci: move ohci_pci_{
suspend,resume} to ohci-hcd.c")' and commit '6ec4beb5c701 ("USB: new
flag for resume-from-hibernation")', the flag "hibernated" is for
resume-from-hibernation and it should be true when usb resume from disk.
When this flag "hibernated" is set, the drivers will reset the hardware
to get rid of any existing state and make sure resume from hibernation
re-enumerates everything for ohci.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20220902063639.17875-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8cb339f1c1 as it
throws up a bunch of sparse warnings as reported by the kernel test
robot.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202209020044.CX2PfZzM-lkp@intel.com
Fixes: 8cb339f1c1 ("usb: gadget: udc-xilinx: replace memcpy with memcpy_toio")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the HC driver is now passed to the function with its
own parameter (it used to be picked from id->driver_data),
the id parameter serves no purpose.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220831125052.71584-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver for the PPC Freescale SoC is using device tree
accessors and imperative GPIO semantics control using the old
GPIO API, switch it over to use GPIO descriptors.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Zhao Qiang <qiang.zhao@freescale.com>
Cc: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220831082932.488724-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB external storage device(0x0b05:1932), use gnome-disk-utility tools
to test usb write < 30MB/s.
if does not to load module of uas for this device, can increase the
write speed from 20MB/s to >40MB/s.
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hu Xiaoying <huxiaoying@kylinos.cn>
Link: https://lore.kernel.org/r/20220901045737.3438046-1-huxiaoying@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of fixes for two long-standing issues with some older
ch341 devices and a number of new device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYxB1GAAKCRALxc3C7H1l
CHefAQCxSTeNfnnRHFC/pHlUFa+4U5tVc8zFnwMcnGcZN79dqAEAkjqdLpH8N3tu
baNUP/l1OH86CL4/Rog/hpbBGzJijQg=
=X+Na
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.0-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
"USB-serial fixes for 6.0-rc4
Here are a couple of fixes for two long-standing issues with some older
ch341 devices and a number of new device ids.
All have been in linux-next with no reported issues."
* tag 'usb-serial-6.0-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ch341: fix disabled rx timer on older devices
USB: serial: ch341: fix lost character on LCR updates
USB: serial: cp210x: add Decagon UCA device id
USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
USB: serial: option: add Quectel EM060K modem
USB: serial: option: add support for OPPO R11 diag port
At least one older CH341 appears to have the RX timer enable bit
inverted so that setting it disables the RX timer and prevents the FIFO
from emptying until it is full.
Only set the RX timer enable bit for devices with version newer than
0x27 (even though this probably affects all pre-0x30 devices).
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Tested-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on reconfiguration")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Disable LCR updates for pre-0x30 devices which use a different (unknown)
protocol for line control and where the current register write causes
the next received character to be lost.
Note that updating LCR using the INIT command has no effect on these
devices either.
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Tested-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on reconfiguration")
Fixes: 55fa15b598 ("USB: serial: ch341: fix baud rate and line-control handling")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 3d5f70949f.
The quirk does not work properly, more work is needed to determine what
should be done here.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Fixes: 3d5f70949f ("usb: add quirks for Lenovo OneLink+ Dock")
Link: https://lore.kernel.org/r/9a17ea86-079f-510d-e919-01bc53a6d09f@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are typically supposed to be quiet unless they are actually
probed, but for some reason, USB host controllers seem to be exempt from
this rule, and happily broadcast their existence into the kernel log at
boot even if the hardware in question is nowhere to be found.
Let's fix that, and remove these pr_info() calls.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Tali Perry <tali.perry1@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Benjamin Fair <benjaminfair@google.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220825170327.674446-1-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBIP driver packs URB transfer flags in network packets that are
exchanged between Server (usbip_host) and Client (vhci_hcd).
URB_* flags are internal to kernel and could change. Where as USBIP
URB flags exchanged in network packets are USBIP user API must not
change.
Add USBIP_URB* flags to make this an explicit API and change the
client and server to map them. Details as follows:
Client tx path (USBIP_CMD_SUBMIT):
- Maps URB_* to USBIP_URB_* when it sends USBIP_CMD_SUBMIT packet.
Server rx path (USBIP_CMD_SUBMIT):
- Maps USBIP_URB_* to URB_* when it receives USBIP_CMD_SUBMIT packet.
Flags aren't included in USBIP_CMD_UNLINK and USBIP_RET_SUBMIT packets
and no special handling is needed for them in the following cases:
- Server rx path (USBIP_CMD_UNLINK)
- Client rx path & Server tx path (USBIP_RET_SUBMIT)
Update protocol documentation to reflect the change.
Suggested-by: Hongren Zenithal Zheng <i@zenithal.me>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220824002456.94605-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During soft disconnect, EP0 events are expected to be handled in order to
allow the controller to successfully move into the halted state. Since
__dwc3_gadget_stop() is executed before polling, EP0 has been disabled, and
events are being blocked. Allow xfercomplete events to be handled, so that
cached SETUP packets can be read out from the internal controller memory.
Without doing so, it will lead to endxfer timeouts, which results to
controller halt failures.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that there are no pending events being handled in between soft
connect/disconnect transitions. As we are keeping interrupts enabled,
and EP0 events are still being serviced, this avoids any stale events from
being serviced.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some operations that need to be ignored if there is a soft
disconnect in progress. This is to avoid having a pending EP0 transfer in
progress while attempting to stop active transfers and halting the
controller.
There were several instances seen where a soft disconnect was able to occur
during early link negotiation, i.e. bus reset/conndone, which leads to the
conndone handler re-configuring EPs while attempting to halt the
controller, as DEP flags are cleared as part of the soft disconnect path.
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
ep0in: cmd 'Set Endpoint Transfer Resource'
ep1out: cmd 'Set Endpoint Transfer Resource'
...
event (00030601): Suspend [U3]
event (00000101): Reset [U0]
ep0out: req ffffff87e5c9e100 length 0/0 zsI ==> 0
event (00000201): Connection Done [U0]
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
In addition, if a soft disconnect occurs, EP0 events are still allowed to
process, however, it will stall/restart during the SETUP phase. The
host is still able to query for the DATA phase, leading to a
xfernotready(DATA) event. Since none of the SETUP transfer parameters are
populated, the xfernotready is treated as a "wrong direction" error,
leading to a duplicate stall/restart routine.
Add the proper softconnect/connected checks in sequences that are
potentially involved during soft disconnect processing.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we look up for endpoint in a table and initate urb endpoint
with it. This is unnecessary because the lookup will always result in
endpoint 0.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Link: https://lore.kernel.org/r/20220824203107.14908-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_maxpacket() looks up the endpoint number in the pipe which can fail
if the interface or configuration changes before the routine is called.
This is unexpected and may even cause a modulo by zero afterwards.
So use usb_endpoint_maxp() routine which uses the endpoint stored in URB
to get the maxpacket.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Addresses-Coverity: 744857 ("Division or modulo by zero")
Addresses-Coverity: 1487371 ("Division or modulo by zero")
Link: https://lore.kernel.org/r/20220824193813.13129-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As follows from #define NAME_TEMPLATE, the procfs code in the RNDIS driver
expects the # of instances to be 3-digit decimal, while the driver calls
ida_simple_get() passing 0 as the 'end' argument which results in actual
max instance # of INT_MAX. Limit the maximum # of RNDIS instances to 1000
which is still a lot! :-)
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/a8180973-3ded-3644-585a-169589a37642@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms make use of VBUS control over PHY which means controller
driver has to access PHY registers to turn on/off VBUS line.This patch
adds support for such platforms in chipidea.
Flag 'CI_HDRC_PHY_VBUS_CONTROL' added to support VBus control feature.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220822054051.2941282-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
these are only used in one place, a few lines lower
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220821145745.122587-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.
Fixes: 249f0a25e8 ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
Fixes: 3f565a363c ("usb: gadget: storage: adapt logic block size to bound block devices")
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1661570110-19127-1-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic kernel fuzzing revealed a recursive locking violation in
usb-storage:
============================================
WARNING: possible recursive locking detected
5.18.0 #3 Not tainted
--------------------------------------------
kworker/1:3/1205 is trying to acquire lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
but task is already holding lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
...
stack backtrace:
CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2988 [inline]
check_deadlock kernel/locking/lockdep.c:3031 [inline]
validate_chain kernel/locking/lockdep.c:3816 [inline]
__lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053
lock_acquire kernel/locking/lockdep.c:5665 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630
__mutex_lock_common kernel/locking/mutex.c:603 [inline]
__mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109
r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622
usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458
device_remove drivers/base/dd.c:545 [inline]
device_remove+0x11f/0x170 drivers/base/dd.c:537
__device_release_driver drivers/base/dd.c:1222 [inline]
device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248
usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627
usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118
usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rondreis <linhaoguo86@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkflDxvg0KWqyZK@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit expanding the scope of the udc_lock mutex in the
gadget core managed to cause an obscure and slightly bizarre lockdep
violation. In abbreviated form:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc7+ #12510 Not tainted
------------------------------------------------------
udevadm/312 is trying to acquire lock:
ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0
but task is already holding lock:
ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (kn->active#4){++++}-{0:0}:
lock_acquire+0x68/0x84
__kernfs_remove+0x268/0x380
kernfs_remove_by_name_ns+0x58/0xac
sysfs_remove_file_ns+0x18/0x24
device_del+0x15c/0x440
-> #2 (device_links_lock){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
device_link_remove+0x3c/0xa0
_regulator_put.part.0+0x168/0x190
regulator_put+0x3c/0x54
devm_regulator_release+0x14/0x20
-> #1 (regulator_list_mutex){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
regulator_lock_dependent+0x54/0x284
regulator_enable+0x34/0x80
phy_power_on+0x24/0x130
__dwc2_lowlevel_hw_enable+0x100/0x130
dwc2_lowlevel_hw_enable+0x18/0x40
dwc2_hsotg_udc_start+0x6c/0x2f0
gadget_bind_driver+0x124/0x1f4
-> #0 (udc_lock){+.+.}-{3:3}:
__lock_acquire+0x1298/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
usb_udc_uevent+0x54/0xe0
Evidently this was caused by the scope of udc_mutex being too large.
The mutex is only meant to protect udc->driver along with a few other
things. As far as I can tell, there's no reason for the mutex to be
held while the gadget core calls a gadget driver's ->bind or ->unbind
routine, or while a UDC is being started or stopped. (This accounts
for link #1 in the chain above, where the mutex is held while the
dwc2_hsotg_udc is started as part of driver probing.)
Gadget drivers' ->disconnect callbacks are problematic. Even though
usb_gadget_disconnect() will now acquire the udc_mutex, there's a
window in usb_gadget_bind_driver() between the times when the mutex is
released and the ->bind callback is invoked. If a disconnect occurred
during that window, we could call the driver's ->disconnect routine
before its ->bind routine. To prevent this from happening, it will be
necessary to prevent a UDC from connecting while it has no gadget
driver. This should be done already but it doesn't seem to be;
currently usb_gadget_connect() has no check for this. Such a check
will have to be added later.
Some degree of mutual exclusion is required in soft_connect_store(),
which can dereference udc->driver at arbitrary times since it is a
sysfs callback. The solution here is to acquire the gadget's device
lock rather than the udc_mutex. Since the driver core guarantees that
the device lock is always held during driver binding and unbinding,
this will make the accesses in soft_connect_store() mutually exclusive
with any changes to udc->driver.
Lastly, it turns out there is one place which should hold the
udc_mutex but currently does not: The function_show() routine needs
protection while it dereferences udc->driver. The missing lock and
unlock calls are added.
Link: https://lore.kernel.org/all/b2ba4245-9917-e399-94c8-03a383e7070e@samsung.com/
Fixes: 2191c00855 ("USB: gadget: Fix use-after-free Read in usb_udc_uevent()")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkfhdxA/I2nOcK7@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 1599069a62 ("phy: core: Warn when phy_power_on is called before
phy_init") the driver complains. In my case (Amlogic SoC) the warning
is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init
So change the order of the two calls. The same change has to be done
to the order of phy_exit() and phy_power_off().
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Cc: stable@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/dfcc6b40-2274-4e86-e73c-5c5e6aa3e046@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retimer device class is left dangling when the typec module
is unloaded. Attempts to reload the module failed with warning:
"sysfs: cannot create duplicate filename '/class/retimer'"
Fixing the issue by unregistering the class properly.
Fixes: ddaf8d96f9 ("usb: typec: Add support for retimers")
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220825140411.10743-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.
Use the struct xhci_plat_priv hack added by commits 46034a999c ("usb:
host: xhci-plat: add platform data support") and f768e71891 ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization to struct usb_hcd")
Fixes: 178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
Those two controllers both have problems with some USB3.0 devices,
particularly self-powered ones. Typical error messages include:
Timeout while waiting for setup device command
device not accepting address X, error -62
unable to enumerate USB device
By process of elimination the controllers themselves were identified as
the cause of the problem. Through trial and error the issue was solved
by using USB_QUIRK_RESET_RESUME for both chips.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220824191320.17883-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
works perfectly with:
modprobe ftdi_sio
echo "0590 00b2" | tee
/sys/module/ftdi_sio/drivers/usb-serial\:ftdi_sio/new_id > /dev/null
but doing this every reboot is a pain in the ass.
Signed-off-by: Niek Nooijens <niek.nooijens@omron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 83810f84ec.
Turning off port power in shutdown did cause issues such as a laptop not
proprly powering off, and some specific usb devies failing to enumerate the
subsequent boot after a warm reset.
So revert this.
Fixes: 83810f84ec ("xhci: turn off port power in shutdown")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.
It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.
In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.
If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.
So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The remove path in xhci platform driver tries to remove and put both main
and shared hcds even if only a main hcd exists (one roothub)
This causes a null pointer dereference in reboot for those controllers.
Check that the shared_hcd exists before trying to remove it.
Fixes: e0fe986972 ("usb: host: xhci-plat: prepare operation w/o shared hcd")
Reported-by: Alexey Sheplyakov <asheplyakov@basealt.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent commit 87d0e2f41b ("usb: typec: ucsi: add a common
function ucsi_unregister_connectors()") introduced a regression that
caused NULL dereference at reading the power supply sysfs. It's a
stale sysfs entry that should have been removed but remains with NULL
ops. The commit changed the error handling to skip the entries after
a NULL con->wq, and this leaves the power device unreleased.
For addressing the regression, the straight revert is applied here.
Further code improvements can be done from the scratch again.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1202386
Link: https://lore.kernel.org/r/87r11cmbx0.wl-tiwai@suse.de
Fixes: 87d0e2f41b ("usb: typec: ucsi: add a common function ucsi_unregister_connectors()")
Cc: <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220823065455.32579-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_qcom_read_usb2_speed() helper is now only called when the
controller is acting as host, but the compiler will warn that the hcd
variable is unused in gadget-only W=1 builds.
Fixes: c06795f114 ("usb: dwc3: qcom: fix gadget-only builds")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220822100550.3039-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On page 362 of the USB3.2 specification (
https://usb.org/sites/default/files/usb_32_20210125.zip),
The 'SuperSpeed Endpoint Companion Descriptor' shall only be returned
by Enhanced SuperSpeed devices that are operating at Gen X speed.
Each endpoint described in an interface is followed by a 'SuperSpeed
Endpoint Companion Descriptor'.
If users use SuperSpeed UDC, host can't recognize the device if endpoint
doesn't have 'SuperSpeed Endpoint Companion Descriptor' followed.
Currently in the uac2 driver code:
1. ss_epout_desc_comp follows ss_epout_desc;
2. ss_epin_fback_desc_comp follows ss_epin_fback_desc;
3. ss_epin_desc_comp follows ss_epin_desc;
4. Only ss_ep_int_desc endpoint doesn't have 'SuperSpeed Endpoint
Companion Descriptor' followed, so we should add it.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Link: https://lore.kernel.org/r/20220721014815.14453-1-quic_jackp@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Program USB2 UTMI pad PD controls during port connect/disconnect.
Power down pad after disconnected to save power.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Link: https://lore.kernel.org/r/20220816082353.13390-3-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last holdout in the drivers/usb/* tree using DEVICE_ATTR() is the
f_mass_storage driver, so move it to use DEVICE_ATTR_RW() instead. The
mode is overridden in the is_visible callback to set it properly
depending on if this is a cdrom or removable device.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Maxim Devaev <mdevaev@gmail.com>
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Neal Liu <neal_liu@aspeedtech.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220810123656.3637104-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RZ/V2M (r9a09g011) has a few differences:
- The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON in
the RZ/V2M hardware manual.
It has additional bits for host and peripheral reset that need to
cleared to use usb host and peripheral respectively.
- The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers
have been moved and renamed to USB_PERI_DRD_STA, USB_PERI_DRD_INT_STA
and USB_PERI_DRD_INT_E.
- The IDMON bit used in the above regs for role detection have moved
from bit 4 to bit 0.
- RZ/V2M has an separate interrupt for DRD, i.e. for changes to IDMON.
- There are reset lines for DRD and USBP
- There is another clock, managed by runtime PM.
Whilst the hardware can support 16 pipes, it is artifically limited
based on the ram per pipe calculation. With the 4KB ram per pipe, we
can support 9 pipes consisting of 4xIN pipes, 4xOUT pipes and PIPE0.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220804192220.128601-3-phil.edworthy@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix CC PHY noise filter of voltage level according to
current cc voltage level
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Link: https://lore.kernel.org/r/20220805071714.150882-8-gene.chen.richtek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible id with rt1715, and add initial setting for
specific support PD30 command.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Link: https://lore.kernel.org/r/20220805071714.150882-6-gene.chen.richtek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the interconnect-initialisation helper by increasing
indentation of (or merging) continuation lines and adding brackets
around multi-line blocks in order to improve readability.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220805074500.21469-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a temporary variable to the interconnect-initialisation helper to
avoid parsing and decoding the 'maximum-speed' devicetree property
twice.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220805074500.21469-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously usb_decode_ctrl() only decodes standard control requests, but
it was used for non-standard requests also. If it's non-standard or
unknown standard bRequest, print the Setup data values.
Fixes: af32423a2d ("usb: dwc3: trace: decode ctrl request")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8d6a30f2f2f953eff833a5bc5aac640a4cc2fc9f.1658971571.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having the Start of Frame Number in the trace data is useful for debugging.
This patch adds the (micro)frame number in which the last packet of the
TRB's buffer was transmitted or received to the trace output.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720215113.1058313-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Printing the event parameters in decimal is not useful.
Print them in hex and make it more practical.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720215113.1058313-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove USB EHCI host controller reset sequence from NPCM7XX USB EHCI
host probe function because it is done in the NPCM reset driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20220718181842.61040-2-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens when @udev->reset_resume is set to true, when usb resume,
the flow as below:
- hub_resume
- usb_disable_interface
- usb_disable_endpoint
- usb_hcd_disable_endpoint
- xhci_endpoint_disable // it set @ep->hcpriv to NULL
Then when reset usb device, it will drop allocated endpoints,
the flow as below:
- usb_reset_and_verify_device
- usb_hcd_alloc_bandwidth
- xhci_mtk_drop_ep
but @ep->hcpriv is already set to NULL, the bandwidth will be not
released anymore.
Due to the added endponts are stored in hash table, we can drop the check
of @ep->hcpriv.
Fixes: 4ce186665e ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220819080556.32215-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently uses the worst case byte budgets on FS/LS bus bandwidth,
for example, for an isochronos IN endpoint with 192 bytes budget, it
will consume the whole 5 uframes(188 * 5) while the actual FS bus
budget should be just 192 bytes. It cause that many usb audio headsets
with 3 interfaces (audio input, audio output, and HID) cannot be
configured.
To improve it, changes to use "approximate" best case budget for FS/LS
bandwidth management. For the same endpoint from the above example,
the approximate best case budget is now reduced to (188 * 2) bytes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220819080556.32215-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err_probe message. Fix it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220803123018.913710-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual
Flash LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the Type-C & Power Delivery controller in
MediaTek MT6370 IC.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Link: https://lore.kernel.org/r/20220815090125.27705-8-peterwu.pub@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7505a9dfa1e097070c492d6f6f84afa2a490b040.1659763173.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
onboard_hub_power_off() currently has a delay after asserting the
reset of the hub. There is already a delay in onboard_hub_power_on()
before de-asserting the reset, which ensures that the reset is
asserted for the required time, so the delay in _power_off() is not
needed.
Skip the reset GPIO check before calling gpiod_set_value_cansleep(),
the function returns early when the GPIO descriptor is NULL.
Reviewed-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220805111836.1.Id5a4dc0a2c046236116693aa55672295513a0f2a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary PCI device ID for the controller
inside the Intel Raptor Lake CPU block. The controllers that
are part of the PCH (chipset) have separate device IDs.
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220815123334.87526-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary ACPI ID for Intel Meteor Lake
IOM devices.
The callback function is_memory() is modified so that it
also checks if the resource descriptor passed to it is a
memory type "Address Space Resource Descriptor".
On Intel Meteor Lake the ACPI memory resource is not
described using the "32-bit Memory Range Descriptor" because
the memory is outside of the 32-bit address space. The
memory resource is described using the "Address Space
Resource Descriptor" instead.
Intel Meteor Lake is the first platform to describe the
memory resource for this device with Address Space Resource
Descriptor, but it most likely will not be the last.
Therefore the change to the is_memory() callback function
is made generic.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable@vger.kernel.org
[ heikki: Rewrote the commit message. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220816101629.69054-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the suspend callbacks by separating the error and success paths
to improve readability.
Also drop a related redundant initialisation.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is the Qualcomm glue wakeup interrupts that may be able to wake the
system from suspend and this can now be described in the devicetree.
Move the wakeup-source property handling over from the core driver and
instead propagate the capability setting to the core device during
probe.
This is needed as there is currently no way for the core driver to query
the wakeup setting of the glue device, but it is the core driver that
manages the PHY power state during suspend.
Also don't leave the PHYs enabled when system wakeup has been disabled
through sysfs.
Fixes: 649f5c842b ("usb: dwc3: core: Host wake up support from system suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit implementing wakeup support in host mode instead broke
suspend for peripheral and OTG mode.
The hack that was added in the suspend path to determine the speed of
any device connected to the USB2 bus not only accesses internal driver
data for a child device, but also dereferences a NULL pointer or
accesses freed data when the controller is not acting as host.
There's no quick fix to the layering violation, but since reverting
would leave us with broken suspend in host mode with wakeup triggering
immediately, let's keep the hack for now.
Fix the immediate issues by only checking the host bus speed and
enabling wakeup interrupts when acting as host.
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A device must enable wakeups during runtime suspend regardless of
whether it is capable and allowed to wake the system up from system
suspend.
Fixes: 2664deb093 ("usb: dwc3: qcom: Honor wakeup enabled/disabled state")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.
After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.
Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.
Also note that runtime PM has been broken since commit 2664deb093
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change added a dependency to the USB host stack and broke
gadget-only builds of the driver.
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d9be8d5c5b.
Generic power-domain flags must be set before the power-domain is
initialised and must specifically not be modified by drivers for devices
that happen to be in the domain.
To make sure that USB power-domains are left enabled during system
suspend when a device in the domain is in the wakeup path, the
GENPD_FLAG_ACTIVE_WAKEUP flag should instead be set for the domain
unconditionally when it is registered.
Note that this also avoids keeping power-domains on during suspend when
wakeup has not been enabled (e.g. through sysfs).
For the runtime PM case, making sure that the PHYs are not suspended and
that they are in the same domain as the controller prevents the domain
from being suspended. If there are cases where this is not possible or
desirable, the genpd implementation may need to be extended.
Fixes: d9be8d5c5b ("usb: dwc3: qcom: Keep power domain on to retain controller status")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHYs must be powered-off before they can be tore down.
Similarly, suspending legacy PHYs after having powered them off makes no
sense.
Fix the dwc3_core_exit() (e.g. called during suspend) and open-coded
dwc3_probe() error-path sequences that got this wrong.
Note that this makes dwc3_core_exit() match the dwc3_core_init() error
path with respect to powering off the PHYs.
Fixes: 03c1fd622f ("usb: dwc3: core: add phy cleanup for probe error handling")
Fixes: c499ff71ff ("usb: dwc3: core: re-factor init and exit paths")
Cc: stable@vger.kernel.org # 4.8
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is USB mass storage primary boot loader for code download on
NXP PN7462AU.
Without the quirk it is impossible to write whole memory at once as
device restarts during the write due to bogus residue values reported.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Witold Lipieta <witold.lipieta@thaumatec.com>
Link: https://lore.kernel.org/r/20220809112911.462776-1-witold.lipieta@thaumatec.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the port does not support USB PD, prevent transition to PD
only states when power supply property is written. In this case,
TCPM transitions to SNK_NEGOTIATE_CAPABILITIES
which should not be the case given that the port is not pd_capable.
[ 84.308251] state change SNK_READY -> SNK_NEGOTIATE_CAPABILITIES [rev3 NONE_AMS]
[ 84.308335] Setting usb_comm capable false
[ 84.323367] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:5000 ret:0
[ 84.323376] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
Fixes: e9e6e164ed ("usb: typec: tcpm: Support non-PD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220817215410.1807477-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning on NOP_USB_XCEIV as builtin broke the TUSB6010 driver because
of an older issue with the depencency.
It is not necessary to forbid NOP_USB_XCEIV=y in combination with
USB_MUSB_HDRC=m, but only the reverse, which causes the link failure
from the original Kconfig change.
Use the correct dependency to still allow NOP_USB_XCEIV=n or
NOP_USB_XCEIV=y but forbid NOP_USB_XCEIV=m when USB_MUSB_HDRC=m
to fix the multi_v7_defconfig for tusb.
Fixes: ab37a7a890 ("ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in")
Fixes: c044247965 ("usb: musb: Fix randconfig build issues for Kconfig options")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220818135737.3143895-10-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make the
tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo). Also
included in here is the obligatory n_gsm updates from Daniel Starke and
lots of tiny driver updates and minor fixes and tweaks for other smaller
serial drivers.
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYvD8qA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfEQCdGiYLQkWUUarhnlocHo+kSm5vkvsAnicZg7Sl
IQBeAidA3dZEQO0lLlM5
=t7Yh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
- convert arm32 to the common dma-direct code (Arnd Bergmann, Robin Murphy,
Christoph Hellwig)
- restructure the PCIe peer to peer mapping support (Logan Gunthorpe)
- allow the IOMMU code to communicate an optional DMA mapping length
and use that in scsi and libata (John Garry)
- split the global swiotlb lock (Tianyu Lan)
- various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
Lukas Bulwahn, Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=Bv19
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- convert arm32 to the common dma-direct code (Arnd Bergmann, Robin
Murphy, Christoph Hellwig)
- restructure the PCIe peer to peer mapping support (Logan Gunthorpe)
- allow the IOMMU code to communicate an optional DMA mapping length
and use that in scsi and libata (John Garry)
- split the global swiotlb lock (Tianyu Lan)
- various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
Lukas Bulwahn, Robin Murphy)
* tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping: (45 commits)
swiotlb: fix passing local variable to debugfs_create_ulong()
dma-mapping: reformat comment to suppress htmldoc warning
PCI/P2PDMA: Remove pci_p2pdma_[un]map_sg()
RDMA/rw: drop pci_p2pdma_[un]map_sg()
RDMA/core: introduce ib_dma_pci_p2p_dma_supported()
nvme-pci: convert to using dma_map_sgtable()
nvme-pci: check DMA ops when indicating support for PCI P2PDMA
iommu/dma: support PCI P2PDMA pages in dma-iommu map_sg
iommu: Explicitly skip bus address marked segments in __iommu_map_sg()
dma-mapping: add flags to dma_map_ops to indicate PCI P2PDMA support
dma-direct: support PCI P2PDMA pages in dma-direct map_sg
dma-mapping: allow EREMOTEIO return code for P2PDMA transfers
PCI/P2PDMA: Introduce helpers for dma_map_sg implementations
PCI/P2PDMA: Attempt to set map_type if it has not been set
lib/scatterlist: add flag for indicating P2PDMA segments in an SGL
swiotlb: clean up some coding style and minor issues
dma-mapping: update comment after dmabounce removal
scsi: sd: Add a comment about limiting max_sectors to shost optimal limit
ata: libata-scsi: cap ata_device->max_sectors according to shost->max_sectors
scsi: scsi_transport_sas: cap shost opt_sectors according to DMA optimal limit
...
- Runtime verification infrastructure
This is the biggest change for this pull request. It introduces the
runtime verification that is necessary for running Linux on safety
critical systems. It allows for deterministic automata models to be
inserted into the kernel that will attach to tracepoints, where the
information on these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will then
activate a given reactor, that could just inform the user or even panic
the kernel (for which safety critical systems will detect and can recover
from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to be
confused with "work in progress"), and Wakeup While Not Running (WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace several
vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is left
off.
- The rest is various cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYu0yzRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qj4HAP4tQtV55rjj4DQ5XIXmtI3/64PmyRSJ
+y4DEXi1UvEUCQD/QAuQfWoT/7gh35ltkfeS4t3ockzy14rrkP5drZigiQA=
=kEtM
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Runtime verification infrastructure
This is the biggest change here. It introduces the runtime
verification that is necessary for running Linux on safety critical
systems.
It allows for deterministic automata models to be inserted into the
kernel that will attach to tracepoints, where the information on
these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will
then activate a given reactor, that could just inform the user or
even panic the kernel (for which safety critical systems will detect
and can recover from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to
be confused with "work in progress"), and Wakeup While Not Running
(WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace
several vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is
left off.
- The rest is various cleanups and fixes.
* tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits)
rv: Unlock on error path in rv_unregister_reactor()
tracing: Use alignof__(struct {type b;}) instead of offsetof()
tracing/eprobe: Show syntax error logs in error_log file
scripts/tracing: Fix typo 'the the' in comment
tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT
tracing: Use free_trace_buffer() in allocate_trace_buffers()
tracing: Use a struct alignof to determine trace event field alignment
rv/reactor: Add the panic reactor
rv/reactor: Add the printk reactor
rv/monitor: Add the wwnr monitor
rv/monitor: Add the wip monitor
rv/monitor: Add the wip monitor skeleton created by dot2k
Documentation/rv: Add deterministic automata instrumentation documentation
Documentation/rv: Add deterministic automata monitor synthesis documentation
tools/rv: Add dot2k
Documentation/rv: Add deterministic automaton documentation
tools/rv: Add dot2c
Documentation/rv: Add a basic documentation
rv/include: Add instrumentation helper functions
rv/include: Add deterministic automata monitor definition via C macros
...
Pull AVR32 updates from Hans-Christian Noren Egtvedt:
"Mostly changes to documentation and comments"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
video:backlight: remove reference to AVR32 architecture in ltv350qv
video: remove support for non-existing atmel,at32ap-lcdc in atmel_lcdfb
usb:udc: remove reference to AVR32 architecture in Atmel USBA Kconfig
sound:spi: remove reference to AVR32 in Atmel AT73C213 DAC driver
net: remove cdns,at32ap7000-macb device tree entry
misc: update maintainer email address and description for atmel-ssc
mfd: remove reference to AVR32 architecture in atmel-smc.c
dma:dw: remove reference to AVR32 architecture in core.c
Clang warns:
drivers/usb/cdns3/cdns3-gadget.c:2290:11: error: variable 'priv_dev' is uninitialized when used here [-Werror,-Wuninitialized]
dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
^~~~~~~~
include/linux/dev_printk.h:155:18: note: expanded from macro 'dev_dbg'
dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:167:7: note: expanded from macro 'dynamic_dev_dbg'
dev, fmt, ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:152:56: note: expanded from macro '_dynamic_func_call'
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~
include/linux/dynamic_debug.h:134:15: note: expanded from macro '__dynamic_func_call'
func(&id, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/usb/cdns3/cdns3-gadget.c:2278:31: note: initialize the variable 'priv_dev' to silence this warning
struct cdns3_device *priv_dev;
^
= NULL
1 error generated.
The priv_dev assignment was moved below the if statement to avoid
potentially dereferencing ep before it was checked but priv_dev is used
in the dev_dbg() call.
To fix this, move the priv_dev and comp_desc assignments back to their
original spot and hoist the ep check above those assignments with a call
to pr_debug() instead of dev_dbg().
Fixes: c3ffc9c4ca ("usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()")
Link: https://github.com/ClangBuiltLinux/linux/issues/1680
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development on
some new hardware support and cleanups of older drivers. Highlights of
this pull request are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this
tool it seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted
as they depened on some typec changes, but the cross-tree
merges caused problems so they will come back later through
the platform tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYup5Rg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yko/ACfYD9mdlr4WleUpVw5/uNywN6sL9EAn1tv0V8W
cUTAoWxAf5orClAC22ZU
=Vcqd
-----END PGP SIGNATURE-----
Merge tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
The AVR32 architecture does no longer exist in the Linux kernel, hence
remove a reference to it in Kconfig help text to avoid confusion.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Merge ACPI device object management changes for v5.20-rc1.
- Use the facilities provided by the driver core and some additional
helpers to handle the children of a given ACPI device object in
multiple places instead of using the children and node list heads in
struct acpi_device which is error prone (Rafael Wysocki).
- Fix ACPI-related device reference counting issue in the hisi_lpc bus
driver (Yang Yingliang).
- Drop the children and node list heads that are not needed any more
from struct acpi_device (Rafael Wysocki).
- Drop driver member from struct acpi_device (Uwe Kleine-König).
- Drop redundant check from acpi_device_remove() (Uwe Kleine-König).
* acpi-bus:
ACPI: bus: Drop unused list heads from struct acpi_device
hisi_lpc: Use acpi_dev_for_each_child()
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
ACPI: bus: Drop driver member of struct acpi_device
ACPI: bus: Drop redundant check in acpi_device_remove()
mfd: core: Use acpi_dev_for_each_child()
ACPI / MMC: PM: Unify fixing up device power
soundwire: Use acpi_dev_for_each_child()
platform/x86/thinkpad_acpi: Use acpi_dev_for_each_child()
ACPI: scan: Walk ACPI device's children using driver core
ACPI: bus: Introduce acpi_dev_for_each_child_reverse()
ACPI: video: Use acpi_dev_for_each_child()
ACPI: bus: Export acpi_dev_for_each_child() to modules
ACPI: property: Use acpi_dev_for_each_child() for child lookup
ACPI: container: Use acpi_dev_for_each_child()
USB: ACPI: Replace usb_acpi_find_port() with acpi_find_child_by_adr()
thunderbolt: ACPI: Replace tb_acpi_find_port() with acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_dev_has_children()
ACPI: glue: Use acpi_dev_for_each_child()
onboard_hub_power_on() already ensures the reset pulse width delay, so
there is no need to wait right after requesting GPIO as well.
Fixes: 40758e493f ("usb: misc: onboard_usb_hub: Add reset-gpio support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220728064937.917935-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Despite default reset upon probe, release reset line after powering up
the hub and assert reset again before powering down.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220727141117.909361-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Microchip USB2514B USB 2.0 hub to the onboard usb hub
driver. Adopt the generic usb-device compatible ("usbVID,PID").
Some STM32MP1 boards have this hub on-board, with a supply that needs to
be enabled for proper operation.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220726080708.162547-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32G0 comes with STM32 bootloader in its system memory. Add support
for some I2C bootloader commands as described in application notes
AN2606 and AN4221, to enable STM32G0 UCSI firmware update.
Upon probing, the driver needs to know the STM32G0 state:
- In bootloader mode, STM32 G0 answers at i2c addr 0x51.
- In running mode, STM32 G0 firmware may answer at two address.
- The main address specified in DT is used for UCSI.
- 0x51 addr can be re-used for FW controls like getting software version
or jump to booloader request.
So probe using the main firmware i2c address first, before attempting
bootloader address (e.g. check for blank, erased or previously aborted
firmware update).
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220713120842.560902-4-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32G0 provides an integrated USB Type-C and power delivery interface.
It can be programmed with a firmware to handle UCSI protocol over I2C
interface. A GPIO is used as an interrupt line.
Type-C connector can be used as a wakeup source (typically to detect
changes on the port, like attach or detach). PM suspend / resume routines
are used to enable wake irqs, and signal a wakeup event in case the IRQ
has fired while in suspend. The i2c core is doing the necessary
initialization when the "wakeup-source" flag is provided.
Note: the interrupt handler shouldn't be called before the i2c bus resumes.
So, the interrupts are disabled during suspend period, and re-enabled
upon resume, to avoid i2c transfer while suspended, from the irq handler.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220713120842.560902-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found PPM will not send any notification after it report error status
and OPM issue GET_ERROR_STATUS command to read the details about error.
According UCSI spec, PPM may clear the Error Status Data after the OPM
has acknowledged the command completion.
This change add operation to acknowledge the command completion from PPM.
Fixes: bdc62f2bae (usb: typec: ucsi: Simplified registration and I/O API)
Cc: <stable@vger.kernel.org> # 5.10
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1658817949-4632-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'ep' is NULL, result of ep_to_cdns3_ep(ep) is invalid pointer
and its dereference with priv_ep->cdns3_dev may cause panic.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Andrey Strachuk <strochuk@ispras.ru>
Link: https://lore.kernel.org/r/20220718160052.4188-1-strochuk@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fwnode_connection_find_match() function handles two cases: named
references and graph endpoints. In the second case, the match function
passed in is called with the id to check for the match. However, the
match function for the recently added type-c retimer class assumes the
connection has already been matched (which is only true for the first
case).
The result is that with that change, all type-c nodes with graph
endpoints defer probe indefinitely, independently of having a retimer
connection or not.
Add the missing check, like is done by the type-c mux and usb role
switch code, to fix the issue.
Fixes: ddaf8d96f9 ("usb: typec: Add support for retimers")
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220725203129.1973260-1-nfraprado@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amireddy mallikarjuna reddy