When wifi is in concurrent mode, we can not distinguish if it is the
real PS or just a fake one by sending null data, so we turn it off
in case of miracast scenario.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During hw initialisation, wifi may be ready after bt has already been
ready, which causes bt to act abnormally. To avoid this, set GNT_BT to
high during hw init.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Stable <stable@vger.kernel.org>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some chips use an external antenna switch, but fw may not realize it.
Here we tell fw exactly that which type of switch we are using.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For a2dp and hid, we need extra process to avoid voice degradation
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If bt is queing, we need to set the packet priority properly.
Originally we only consider if wifi was connected or not, but now we
also consider if bt is under abnormal scan or wifi is scanning, roaming
or linking, and set the coex table.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the hardware initialisation stage, the PTA circuits may be unstable,
so we reset it after 6 secs to fix the problem.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These cases are for the btcoex to tune the performance
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If ap num < 10, let wifi and bt transmit simultaneously, otherwise set
wifi into standy when bt is transmitting
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable is for PS tdma duration adjust, so rename it to clearly
to specify its usage.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For time division multiple access, the wifi and bt take turns to
transmit, but we need to let AP know that wifi is under standby mode by
sending null data to "pretend" entering power saving state using lps
rpwm.
But, the fw does not know if it is the actual power saving mode or just a
fake one to cheat to the AP. Hence, before fw setting the tdma duration,
the fw needs the driver to check the power saving state first.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When receiving pno results there may be duplicate channels and/or
ssids. Assure each is added only once when preparing the internal
escan request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checking whether the address of an array element is null is bogus
so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The fwsignal module is part of the bcdc protocol and as such does
its instance data is not needed in core structure. Moving it into
struct brcmf_bcdc instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc
field is initialized regardless the state of the fwsignal functionality,
ie. the fcmode. This is not needed when fcmode is NONE, which is the
default mode.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a non-functional change to align the fwsignal module to
the naming pattern used throughout the driver.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Systems with 64 bit DMA at least partially require buffers to be used
for DMA to be 8-byte-aligned. One example is Amlogic Meson GX.
Switching the MMC/SDIO driver for this platform to SG DMA mode
resulted in problems due to unaligned buffers.
Fortunately the brcmfmac driver has a global define for the alignment.
Changing it to 8 fixed the issues with Meson GX.
Suggested-by: Helmut Klein <hgkr.klein@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have to use start port, for TX/RX of single packet,
instead of current aggregating port. This will fix SDIO
CMD53(TX/RX) returning -ETIMEDOUT and halting the data path.
Fixes: 0cb52aac4d ("mwifiex: do not set multiport flag for tx/rx single packet")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case wil6210 resume fails, wil6210 suspend function will try
to access the suspended device in the next kernel suspend.
To prevent that, add wil_status_suspended flag to indicate if the
device is already suspended and clear it only if the resume succeeds.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Array index 'i' is used before limits check.
Fix this by doing limits check first.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver fails to load FW for sparrow D0 devices in some cases.
Fix this by returning correct value from wil_fw_verify_file_exists
when D0 FW file is not detected for any reason.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During the suspend flow, wil6210 HW can send sporadic interrupts,
while PCIe bus is not operational.
To prevent that, keep the interrupts disabled during the suspend
flow and re-enable them only after PCIe enablement in resume.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing code that ignores connection events during
reset flow will never take effect since it locks the
same mutex taken by the reset flow.
In addition, in case of unsolicited disconnect events ignore
those as well since device is about to get reset.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Communication with FW must be done before wil->status
is initialized in order to properly handle cases where
communication with FW halts during reset sequence.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix fallout too.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This field is never big enough to warrant 16-bitness.
8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit
accesses:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
function old new delta
loopback_setup 169 164 -5
ether_setup 148 143 -5
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may use build_skb() for received packets.
These SKBs then have a head_frag.
Since commit d7e8883cfc ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.
Commit 07b26c9454 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.
A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.
This causes low performance when forwarding those packets
that were built with build_skb()
Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.
Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*()
Declare parameters of these functions as "const" where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt says:
====================
ftgmac100: Rework batch 4 - Misc
This is v2 of the fourth batch of updates to the ftgmac100 driver.
This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.
This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.
v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)
The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So features can be turned on/off via ethtool
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: patches for net-next
here are some patches for net/smc. Most important are
improvements for socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yan-Hsuan Chuang