CoDel can be too aggressive if a station sends at a very low rate,
leading reduced throughput. This gets worse the more stations are
present, as each station gets more bursty the longer the round-robin
scheduling between stations takes.
This adds dynamic adjustment of CoDel parameters per station. It uses
the rate selection information to estimate throughput and sets more
lenient CoDel parameters if the estimated throughput is below a
threshold (modified by the number of active stations).
A new callback is added that drivers can use to notify mac80211 about
changes in expected throughput, so the same adjustment can be made for
cards that implement rate control in firmware. Drivers that don't use
this will just get the default parameters.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove
inline annotation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BBR congestion control depends on pacing, and pacing is
currently handled by sch_fq packet scheduler for performance reasons,
and also because implemening pacing with FQ was convenient to truly
avoid bursts.
However there are many cases where this packet scheduler constraint
is not practical.
- Many linux hosts are not focusing on handling thousands of TCP
flows in the most efficient way.
- Some routers use fq_codel or other AQM, but still would like
to use BBR for the few TCP flows they initiate/terminate.
This patch implements an automatic fallback to internal pacing.
Pacing is requested either by BBR or use of SO_MAX_PACING_RATE option.
If sch_fq happens to be in the egress path, pacing is delegated to
the qdisc, otherwise pacing is done by TCP itself.
One advantage of pacing from TCP stack is to get more precise rtt
estimations, and less work done from TX completion, since TCP Small
queue limits are not generally hit. Setups with single TX queue but
many cpus might even benefit from this.
Note that unlike sch_fq, we do not take into account header sizes.
Taking care of these headers would add additional complexity for
no practical differences in behavior.
Some performance numbers using 800 TCP_STREAM flows rate limited to
~48 Mbit per second on 40Gbit NIC.
If MQ+pfifo_fast is used on the NIC :
$ sar -n DEV 1 5 | grep eth
14:48:44 eth0 725743.00 2932134.00 46776.76 4335184.68 0.00 0.00 1.00
14:48:45 eth0 725349.00 2932112.00 46751.86 4335158.90 0.00 0.00 0.00
14:48:46 eth0 725101.00 2931153.00 46735.07 4333748.63 0.00 0.00 0.00
14:48:47 eth0 725099.00 2931161.00 46735.11 4333760.44 0.00 0.00 1.00
14:48:48 eth0 725160.00 2931731.00 46738.88 4334606.07 0.00 0.00 0.00
Average: eth0 725290.40 2931658.20 46747.54 4334491.74 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
4 0 0 259825920 45644 2708324 0 0 21 2 247 98 0 0 100 0 0
4 0 0 259823744 45644 2708356 0 0 0 0 2400825 159843 0 19 81 0 0
0 0 0 259824208 45644 2708072 0 0 0 0 2407351 159929 0 19 81 0 0
1 0 0 259824592 45644 2708128 0 0 0 0 2405183 160386 0 19 80 0 0
1 0 0 259824272 45644 2707868 0 0 0 32 2396361 158037 0 19 81 0 0
Now use MQ+FQ :
lpaa23:~# echo fq >/proc/sys/net/core/default_qdisc
lpaa23:~# tc qdisc replace dev eth0 root mq
$ sar -n DEV 1 5 | grep eth
14:49:57 eth0 678614.00 2727930.00 43739.13 4033279.14 0.00 0.00 0.00
14:49:58 eth0 677620.00 2723971.00 43674.69 4027429.62 0.00 0.00 1.00
14:49:59 eth0 676396.00 2719050.00 43596.83 4020125.02 0.00 0.00 0.00
14:50:00 eth0 675197.00 2714173.00 43518.62 4012938.90 0.00 0.00 1.00
14:50:01 eth0 676388.00 2719063.00 43595.47 4020171.64 0.00 0.00 0.00
Average: eth0 676843.00 2720837.40 43624.95 4022788.86 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 259832240 46008 2710912 0 0 21 2 223 192 0 1 99 0 0
1 0 0 259832896 46008 2710744 0 0 0 0 1702206 198078 0 17 82 0 0
0 0 0 259830272 46008 2710596 0 0 0 0 1696340 197756 1 17 83 0 0
4 0 0 259829168 46024 2710584 0 0 16 0 1688472 197158 1 17 82 0 0
3 0 0 259830224 46024 2710408 0 0 0 0 1692450 197212 0 18 82 0 0
As expected, number of interrupts per second is very different.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
under udp flood the sk_receive_queue spinlock is heavily contended.
This patch try to reduce the contention on such lock adding a
second receive queue to the udp sockets; recvmsg() looks first
in such queue and, only if empty, tries to fetch the data from
sk_receive_queue. The latter is spliced into the newly added
queue every time the receive path has to acquire the
sk_receive_queue lock.
The accounting of forward allocated memory is still protected with
the sk_receive_queue lock, so udp_rmem_release() needs to acquire
both locks when the forward deficit is flushed.
On specific scenarios we can end up acquiring and releasing the
sk_receive_queue lock multiple times; that will be covered by
the next patch
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And update __sk_queue_drop_skb() to work on the specified queue.
This will help the udp protocol to use an additional private
rx queue in a later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas reports that the following incremental update using our commit
protocol doesn't work.
# nft -f incremental-update.nft
delete element ip filter client_to_any { 10.180.86.22 : goto CIn_1 }
delete chain ip filter CIn_1
... Error: Could not process rule: Device or resource busy
The existing code is not well-integrated into the commit phase protocol,
since element deletions do not result in refcount decrement from the
preparation phase. This results in bogus EBUSY errors like the one
above.
Two new functions come with this patch:
* nft_set_elem_activate() function is used from the abort path, to
restore the set element refcounting on objects that occurred from
the preparation phase.
* nft_set_elem_deactivate() that is called from nft_del_setelem() to
decrement set element refcounting on objects from the preparation
phase in the commit protocol.
The nft_data_uninit() has been renamed to nft_data_release() since this
function does not uninitialize any data store in the data register,
instead just releases the references to objects. Moreover, a new
function nft_data_hold() has been introduced to be used from
nft_set_elem_activate().
Reported-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can still delete the ct helper even if it is in use, this will cause
a use-after-free error. In more detail, I mean:
# nfct helper add ssdp inet udp
# iptables -t raw -A OUTPUT -p udp -j CT --helper ssdp
# nfct helper delete ssdp //--> oops, succeed!
BUG: unable to handle kernel paging request at 000026ca
IP: 0x26ca
[...]
Call Trace:
? ipv4_helper+0x62/0x80 [nf_conntrack_ipv4]
nf_hook_slow+0x21/0xb0
ip_output+0xe9/0x100
? ip_fragment.constprop.54+0xc0/0xc0
ip_local_out+0x33/0x40
ip_send_skb+0x16/0x80
udp_send_skb+0x84/0x240
udp_sendmsg+0x35d/0xa50
So add reference count to fix this issue, if ct helper is used by
others, reject the delete request.
Apply this patch:
# nfct helper delete ssdp
nfct v1.4.3: netlink error: Device or resource busy
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
And convert module_put invocation to nf_conntrack_helper_put, this is
prepared for the followup patch, which will add a refcnt for cthelper,
so we can reject the deleting request when cthelper is in use.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull RCU updates from Ingo Molnar:
"The main changes are:
- Debloat RCU headers
- Parallelize SRCU callback handling (plus overlapping patches)
- Improve the performance of Tree SRCU on a CPU-hotplug stress test
- Documentation updates
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (74 commits)
rcu: Open-code the rcu_cblist_n_lazy_cbs() function
rcu: Open-code the rcu_cblist_n_cbs() function
rcu: Open-code the rcu_cblist_empty() function
rcu: Separately compile large rcu_segcblist functions
srcu: Debloat the <linux/rcu_segcblist.h> header
srcu: Adjust default auto-expediting holdoff
srcu: Specify auto-expedite holdoff time
srcu: Expedite first synchronize_srcu() when idle
srcu: Expedited grace periods with reduced memory contention
srcu: Make rcutorture writer stalls print SRCU GP state
srcu: Exact tracking of srcu_data structures containing callbacks
srcu: Make SRCU be built by default
srcu: Fix Kconfig botch when SRCU not selected
rcu: Make non-preemptive schedule be Tasks RCU quiescent state
srcu: Expedite srcu_schedule_cbs_snp() callback invocation
srcu: Parallelize callback handling
kvm: Move srcu_struct fields to end of struct kvm
rcu: Fix typo in PER_RCU_NODE_PERIOD header comment
rcu: Use true/false in assignment to bool
rcu: Use bool value directly
...
This reverts commit 82486aa6f1.
As implemented, this causes dangling netdevice refs.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f5
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* don't try to authenticate during reconfiguration, which causes
drivers to get confused
* fix a kernel-doc warning for a recently merged change
* fix MU-MIMO group configuration (relevant only for monitor mode)
* more rate flags fix: remove stray RX_ENC_FLAG_40MHZ
* fix IBSS probe response allocation size
-----BEGIN PGP SIGNATURE-----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=FcxE
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple more fixes:
* don't try to authenticate during reconfiguration, which causes
drivers to get confused
* fix a kernel-doc warning for a recently merged change
* fix MU-MIMO group configuration (relevant only for monitor mode)
* more rate flags fix: remove stray RX_ENC_FLAG_40MHZ
* fix IBSS probe response allocation size
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Congestion control modules that want full control over congestion
control behavior do not want the cwnd modifications controlled by
the sysctl_tcp_slow_start_after_idle code path.
So skip those code paths for CC modules that use the cong_control()
API.
As an example, those cwnd effects are not desired for the BBR congestion
control algorithm.
Fixes: c0402760f5 ("tcp: new CC hook to set sending rate with rate_sample in any CA state")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 dst could use fi->fib_metrics to store metrics but fib_info
itself is refcnt'ed, so without taking a refcnt fi and
fi->fib_metrics could be freed while dst metrics still points to
it. This triggers use-after-free as reported by Andrey twice.
This patch reverts commit 2860583fe8 ("ipv4: Kill rt->fi") to
restore this reference counting. It is a quick fix for -net and
-stable, for -net-next, as Eric suggested, we can consider doing
reference counting for metrics itself instead of relying on fib_info.
IPv6 is very different, it copies or steals the metrics from mx6_config
in fib6_commit_metrics() so probably doesn't need a refcnt.
Decnet has already done the refcnt'ing, see dn_fib_semantic_match().
Fixes: 2860583fe8 ("ipv4: Kill rt->fi")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace @results_wk with @report_results, which was missed
in an earlier patch between revisions thereof.
Fixes: b34939b983 ("cfg80211: add request id to cfg80211_sched_scan_*() api")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow I missed this in my RX rate cleanup series, causing some
drivers to not report correct bandwidth since this flag isn't
used by mac80211 anymore. Fix this, and make hwsim also report
higher bandwidths appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whole point of randomization was to hide server uptime, but an attacker
can simply start a syn flood and TCP generates 'old style' timestamps,
directly revealing server jiffies value.
Also, TSval sent by the server to a particular remote address vary
depending on syncookies being sent or not, potentially triggering PAWS
drops for innocent clients.
Lets implement proper randomization, including for SYNcookies.
Also we do not need to export sysctl_tcp_timestamps, since it is not
used from a module.
In v2, I added Florian feedback and contribution, adding tsoff to
tcp_get_cookie_sock().
v3 removed one unused variable in tcp_v4_connect() as Florian spotted.
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The wireless rate info fix from Johannes Berg.
2) When a RAW socket is in hdrincl mode, we need to make sure that the
user provided at least a minimally sized ipv4/ipv6 header. Fix from
Alexander Potapenko.
3) We must emit IFLA_PHYS_PORT_NAME netlink attributes using
nla_put_string() so that it is NULL terminated.
4) Fix a bug in TCP fastopen handling, wherein child sockets
erroneously inherit the fastopen_req from the parent, and later can
end up derefencing freed memory or doing a double free. From Eric
Dumazet.
5) Don't clear out netdev stats at close time in tg3 driver, from
YueHaibing.
6) Fix refcount leak in xt_CT, from Gao Feng.
7) In nft_set_bitmap() don't leak dummy elements, from Liping Zhang.
8) Fix deadlock due to taking the expectation lock twice, also from
Liping Zhang.
9) Make xt_socket work again with ipv6, from Peter Tirsek.
10) Don't allow IPV6 to be used with IPVS if ipv6.disable=1, from Paolo
Abeni.
11) Make the BPF loader more flexible wrt. changes to the bpf MAP entry
layout. From Jesper Dangaard Brouer.
12) Fix ethtool reported device name in aquantia driver, from Pavel
Belous.
13) Fix build failures due to the compile time size test not working in
netfilter conntrack. From Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
cfg80211: make RATE_INFO_BW_20 the default
ipv6: initialize route null entry in addrconf_init()
qede: Fix possible misconfiguration of advertised autoneg value.
qed: Fix overriding of supported autoneg value.
qed*: Fix possible overflow for status block id field.
rtnetlink: NUL-terminate IFLA_PHYS_PORT_NAME string
netvsc: make sure napi enabled before vmbus_open
aquantia: Fix driver name reported by ethtool
ipv4, ipv6: ensure raw socket message is big enough to hold an IP header
net/sched: remove redundant null check on head
tcp: do not inherit fastopen_req from parent
forcedeth: remove unnecessary carrier status check
ibmvnic: Move queue restarting in ibmvnic_tx_complete
ibmvnic: Record SKB RX queue during poll
ibmvnic: Continue skb processing after skb completion error
ibmvnic: Check for driver reset first in ibmvnic_xmit
ibmvnic: Wait for any pending scrqs entries at driver close
ibmvnic: Clean up tx pools when closing
ibmvnic: Whitespace correction in release_rx_pools
ibmvnic: Delete napi's when releasing driver resources
...
Due to the way I did the RX bitrate conversions in mac80211 with
spatch, going setting flags to setting the value, many drivers now
don't set the bandwidth value for 20 MHz, since with the flags it
wasn't necessary to (there was no 20 MHz flag, only the others.)
Rather than go through and try to fix up all the drivers, instead
renumber the enum so that 20 MHz, which is the typical bandwidth,
actually has the value 0, making those drivers all work again.
If VHT was hit used with a driver not reporting it, e.g. iwlmvm,
this manifested in hitting the bandwidth warning in
cfg80211_calculate_bitrate_vht().
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_XFRM_SUB_POLICY=y, xfrm_dst stores a copy of the flowi for
that dst. Unfortunately, the code that allocates and fills this copy
doesn't care about what type of flowi (flowi, flowi4, flowi6) gets
passed. In multiple code paths (from raw_sendmsg, from TCP when
replying to a FIN, in vxlan, geneve, and gre), the flowi that gets
passed to xfrm is actually an on-stack flowi4, so we end up reading
stuff from the stack past the end of the flowi4 struct.
Since xfrm_dst->origin isn't used anywhere following commit
ca116922af ("xfrm: Eliminate "fl" and "pol" args to
xfrm_bundle_ok()."), just get rid of it. xfrm_dst->partner isn't used
either, so get rid of that too.
Fixes: 9d6ec93801 ("ipv4: Use flowi4 in public route lookup interfaces.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
- idr usage and locking changes
- build fix for hns
- ipoib debug path record file fix
- hfi1 updates
- core RDMA netdev addition
- Intel VNIC driver addition
- Enhanced accelerators for IPoIB addition
- Debug cleanups in cxgb3/4
- Trivial cleanups from SF Markus Elfring
- Misc rxe fixes from Mellanox
- Misc ipoib fixes from Mellanox
- Lots of mlx4/mlx5 changes from Mellanox
- Misc fixes across the RDMA subsystem
- ODP paging fixes and improvements
- qedr updates
- hfi1 updates
- OPA port info patches
- OPA AH patches
- OPA SA Query patches
-----BEGIN PGP SIGNATURE-----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=pgEL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"More exchaustive description of primary updates in this release:
- Lots of driver fixes and misc fixes across the board.
- I had to base on a net-next tree because the IPoIB Accelorator
patches needed it.
Unfortunately, it was known to Mellanox that there would need to be
an IPoIB accelorator patch to the net tree (which left some
functions turned off by an #ifdef construct to avoid warnings about
defined but unused functions), then one to the RDMA tree, then a
fixup that went back and re-enabled the functions in the net tree
and enabled their use in the rdma tree
Also, a sparse fix was sent to the net tree after I did my pull,
and the fixup patch conflicts quite directly with that sparse fix,
so I'm going to submit the fixup patch towards the end of the merge
window by itself and based upon your master branch at the time.
- Two separate rounds of hfi1 fixes, one that got dropped from last
release because it came in just a day or two before the end of the
merge window and then the one from this release cycle.
Of note is that I now have a third series that just landed from
Intel yesterday. It is not included in this pull request, but I may
submit it by the end of the week. I'll talk to Intel about
improving the timing of thier submissions for my workflow.
- Changes to our idr usage in the RDMA subsystem that will tie into
our cgroup management and also into the upcoming changes for the
RDMA kernel<->userspace API.
- Addition of support for a netdev to be tied to an RDMA device at
the core level
- Addition of the VNIC driver from Intel.
While IPoIB provides IP over InfiniBand (and *only* IP, no lower
layer protocol headers are allowed or supported), the VNIC driver
presents a virtual Ethernet device with support for things like
varying Ethertypes, VLANs, priorities and other features of
Ethernet.
The virtual devices are centrally managed by the OPA fabric
manager, making this (for the time being) a strictly OPA specific
feature.
- Improvements to the On-Demand Paging support in the RDMA subsystem.
- Addition of three significant OPA changes.
While we added OPA support some time ago (via the hfi1 driver), the
RDMA subsystem has so far glossed over the areas where OPA and
InfiniBand differ.
With this release we are starting to add support for the OPA
extensions into the RDMA core in the following area: Extended port
information for OPA is now supported, extended Address Handle
attributes for OPA are now supported, and extended SA Queries to
get OPA specific subnet information is now supported.
Concise summary from the tag:
- idr usage and locking changes
- build fix for hns
- ipoib debug path record file fix
- hfi1 updates
- core RDMA netdev addition
- Intel VNIC driver addition
- Enhanced accelerators for IPoIB addition
- Debug cleanups in cxgb3/4
- Trivial cleanups from SF Markus Elfring
- Misc rxe fixes from Mellanox
- Misc ipoib fixes from Mellanox
- Lots of mlx4/mlx5 changes from Mellanox
- Misc fixes across the RDMA subsystem
- ODP paging fixes and improvements
- qedr updates
- hfi1 updates
- OPA port info patches
- OPA AH patches
- OPA SA Query patches"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (191 commits)
infiniband: avoid dereferencing uninitialized dst on error path
IB/SA: Add OPA addr header
IB/mlx5: Add port_xmit_wait to counter registers read
IB/ocrdma: fix out of bounds access to local buffer
IB/mlx4: Fix incorrect order of formal and actual parameters
IB/mlx4: Change flush logic so it adheres to the variable name
mlx5: Fix mlx5_ib_map_mr_sg mr length
IB/rxe: Don't clamp residual length to mtu
IB/SA: Add support to query OPA path records
IB/SA: Add OPA path record type
IB/SA: Split struct sa_path_rec based on IB and ROCE specific fields
IB/SA: Introduce path record specific types
IB/SA: Rename ib_sa_path_rec to sa_path_rec
IB/CM: Add braces when using sizeof
IB/core: Define 'opa' rdma_ah_attr type
IB/core: Define 'ib' and 'roce' rdma_ah_attr types
IB/core: Use rdma_ah_attr accessor functions
IB/core: Add accessor functions for rdma_ah_attr fields
IB/PVRDMA: Rename ib_ah_attr related functions
IB/mthca: Rename to_ib_ah_attr to to_rdma_ah_attr
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. A large bunch of code cleanups, simplify the conntrack extension
codebase, get rid of the fake conntrack object, speed up netns by
selective synchronize_net() calls. More specifically, they are:
1) Check for ct->status bit instead of using nfct_nat() from IPVS and
Netfilter codebase, patch from Florian Westphal.
2) Use kcalloc() wherever possible in the IPVS code, from Varsha Rao.
3) Simplify FTP IPVS helper module registration path, from Arushi Singhal.
4) Introduce nft_is_base_chain() helper function.
5) Enforce expectation limit from userspace conntrack helper,
from Gao Feng.
6) Add nf_ct_remove_expect() helper function, from Gao Feng.
7) NAT mangle helper function return boolean, from Gao Feng.
8) ctnetlink_alloc_expect() should only work for conntrack with
helpers, from Gao Feng.
9) Add nfnl_msg_type() helper function to nfnetlink to build the
netlink message type.
10) Get rid of unnecessary cast on void, from simran singhal.
11) Use seq_puts()/seq_putc() instead of seq_printf() where possible,
also from simran singhal.
12) Use list_prev_entry() from nf_tables, from simran signhal.
13) Remove unnecessary & on pointer function in the Netfilter and IPVS
code.
14) Remove obsolete comment on set of rules per CPU in ip6_tables,
no longer true. From Arushi Singhal.
15) Remove duplicated nf_conntrack_l4proto_udplite4, from Gao Feng.
16) Remove unnecessary nested rcu_read_lock() in
__nf_nat_decode_session(). Code running from hooks are already
guaranteed to run under RCU read side.
17) Remove deadcode in nf_tables_getobj(), from Aaron Conole.
18) Remove double assignment in nf_ct_l4proto_pernet_unregister_one(),
also from Aaron.
19) Get rid of unsed __ip_set_get_netlink(), from Aaron Conole.
20) Don't propagate NF_DROP error to userspace via ctnetlink in
__nf_nat_alloc_null_binding() function, from Gao Feng.
21) Revisit nf_ct_deliver_cached_events() to remove unnecessary checks,
from Gao Feng.
22) Kill the fake untracked conntrack objects, use ctinfo instead to
annotate a conntrack object is untracked, from Florian Westphal.
23) Remove nf_ct_is_untracked(), now obsolete since we have no
conntrack template anymore, from Florian.
24) Add event mask support to nft_ct, also from Florian.
25) Move nf_conn_help structure to
include/net/netfilter/nf_conntrack_helper.h.
26) Add a fixed 32 bytes scratchpad area for conntrack helpers.
Thus, we don't deal with variable conntrack extensions anymore.
Make sure userspace conntrack helper doesn't go over that size.
Remove variable size ct extension infrastructure now this code
got no more clients. From Florian Westphal.
27) Restore offset and length of nf_ct_ext structure to 8 bytes now
that wraparound is not possible any longer, also from Florian.
28) Allow to get rid of unassured flows under stress in conntrack,
this applies to DCCP, SCTP and TCP protocols, from Florian.
29) Shrink size of nf_conntrack_ecache structure, from Florian.
30) Use TCP_MAX_WSCALE instead of hardcoded 14 in TCP tracker,
from Gao Feng.
31) Register SYNPROXY hooks on demand, from Florian Westphal.
32) Use pernet hook whenever possible, instead of global hook
registration, from Florian Westphal.
33) Pass hook structure to ebt_register_table() to consolidate some
infrastructure code, from Florian Westphal.
34) Use consume_skb() and return NF_STOLEN, instead of NF_DROP in the
SYNPROXY code, to make sure device stats are not fooled, patch
from Gao Feng.
35) Remove NF_CT_EXT_F_PREALLOC this kills quite some code that we
don't need anymore if we just select a fixed size instead of
expensive runtime time calculation of this. From Florian.
36) Constify nf_ct_extend_register() and nf_ct_extend_unregister(),
from Florian.
37) Simplify nf_ct_ext_add(), this kills nf_ct_ext_create(), from
Florian.
38) Attach NAT extension on-demand from masquerade and pptp helper
path, from Florian.
39) Get rid of useless ip_vs_set_state_timeout(), from Aaron Conole.
40) Speed up netns by selective calls of synchronize_net(), from
Florian Westphal.
41) Silence stack size warning gcc in 32-bit arch in snmp helper,
from Florian.
42) Inconditionally call nf_ct_ext_destroy(), even if we have no
extensions, to deal with the NF_NAT_MANIP_SRC case. Patch from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For NF_NAT_MANIP_SRC, we will insert the ct to the nat_bysource_table,
then remove it from the nat_bysource_table via nat_extend->destroy.
But now, the nat extension is attached on demand, so if the nat extension
is not attached, we will not be notified when the ct is destroyed, i.e.
we may fail to remove ct from the nat_bysource_table.
So just keep it simple, even if the extension is not attached, we will
still invoke the related ext->destroy. And this will also preserve the
flexibility for the future extension.
Fixes: 9a08ecfe74 ("netfilter: don't attach a nat extension by default")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simon Horman says:
====================
Third Round of IPVS Updates for v4.12
please consider these enhancements to IPVS for v4.12.
If it is too late for v4.12 then please consider them for v4.13.
* Remove unused function
* Correct comparison of unsigned value
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_unregister_net_hook(s) can avoid a second call to synchronize_net,
provided there is no nfqueue active in that net namespace (which is
the common case).
This also gets rid of the extra arg to nf_queue_nf_hook_drop(), normally
this gets called during netns cleanup so no packets should be queued.
For the rare case of base chain being unregistered or module removal
while nfqueue is in use the extra hiccup due to the packet drops isn't
a big deal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
-----BEGIN PGP SIGNATURE-----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=dYTw
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of patches for -next:
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no in-tree callers of this function and it isn't exported.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.
As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.
Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[use C99 initializers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack
struct ieee80211_tx_status instead of struct ieee80211_tx_info.
This struct can be used to pass extra information, e.g. for dynamic tx
power control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows for the scheduled scan request to specify matchsets
for specific BSSIDs.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[docs, netlink policy fix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate a portid structure and then, for
each of those, walk the interfaces - we can just add a flag
to each interface and walk those directly. Due to padding in
the struct, we can even do it without any memory cost, and
it even simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No longer needed, since tp->tcp_mstamp holds the information.
This is needed to remove sack_state.ack_time in a following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer needed, since tp->tcp_mstamp holds the information.
This is needed to remove sack_state.ack_time in a following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is no longer used, since tcp_rack_detect_loss() takes
the timestamp from tp->tcp_mstamp
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nowadays the NAT extension only stores the interface index
(used to purge connections that got masqueraded when interface goes down)
and pptp nat information.
Previous patches moved nf_ct_nat_ext_add to those places that need it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It was used by the nat extension, but since commit
7c96643519 ("netfilter: move nat hlist_head to nf_conn") its only needed
for connections that use MASQUERADE target or a nat helper.
Also it seems a lot easier to preallocate a fixed size instead.
With default settings, conntrack first adds ecache extension (sysctl
defaults to 1), so we get 40(ct extension header) + 24 (ecache) == 64 byte
on x86_64 for initial allocation.
Followup patches can constify the extension structs and avoid
the initial zeroing of the entire extension area.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Defer registration of the synproxy hooks until the first SYNPROXY rule is
added. Also means we only register hooks in namespaces that need it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This logic seems to be duplicated in (at least) three separate files.
Move it to one place so code can be re-use.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
The CAN gateway was not implemented as per-net in the initial network
namespace support by Mario Kicherer (8e8cda6d73).
This patch enables the CAN gateway to be used in different namespaces.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_BCM protocol and its procfs entries were not implemented as per-net
in the initial network namespace support by Mario Kicherer (8e8cda6d73).
This patch adds the missing per-net functionality for the CAN BCM.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The statistics and its proc output was not implemented as per-net in the
initial network namespace support by Mario Kicherer (8e8cda6d73).
This patch adds the missing per-net statistics for the CAN subsystem.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for parsing MPLS flows to the flow dissector in preparation for
adding MPLS match support to cls_flower.
Signed-off-by: Benjamin LaHaise <benjamin.lahaise@netronome.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Eric Dumazet <jhs@mojatatu.com>
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Gao Feng <fgao@ikuai8.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter records the number of times the firewall blackhole issue is
detected and active TFO is disabled.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Middlebox firewall issues can potentially cause server's data being
blackholed after a successful 3WHS using TFO. Following are the related
reports from Apple:
https://www.nanog.org/sites/default/files/Paasch_Network_Support.pdf
Slide 31 identifies an issue where the client ACK to the server's data
sent during a TFO'd handshake is dropped.
C ---> syn-data ---> S
C <--- syn/ack ----- S
C (accept & write)
C <---- data ------- S
C ----- ACK -> X S
[retry and timeout]
https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf
Slide 5 shows a similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
This is the worst failure b/c the client can not detect such behavior to
mitigate the situation (such as disabling TFO). Failing to proceed, the
application (e.g., SSL library) may simply timeout and retry with TFO
again, and the process repeats indefinitely.
The proposed solution is to disable active TFO globally under the
following circumstances:
1. client side TFO socket detects out of order FIN
2. client side TFO socket receives out of order RST
We disable active side TFO globally for 1hr at first. Then if it
happens again, we disable it for 2h, then 4h, 8h, ...
And we reset the timeout to 1hr if a client side TFO sockets not opened
on loopback has successfully received data segs from server.
And we examine this condition during close().
The rational behind it is that when such firewall issue happens,
application running on the client should eventually close the socket as
it is not able to get the data it is expecting. Or application running
on the server should close the socket as it is not able to receive any
response from client.
In both cases, out of order FIN or RST will get received on the client
given that the firewall will not block them as no data are in those
frames.
And we want to disable active TFO globally as it helps if the middle box
is very close to the client and most of the connections are likely to
fail.
Also, add a debug sysctl:
tcp_fastopen_blackhole_detect_timeout_sec:
the initial timeout to use when firewall blackhole issue happens.
This can be set and read.
When setting it to 0, it means to disable the active disable logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+5cRAAoJEEg/ir3gV/o+5c8H/1/khPzy26B2lWyjPC8CRCQF
eSd0tiHLgIqbZTbnIHTR+NbZ/SUFaukoJi8OKn1fGFHCCajWvPP4xkENVKrUdi3q
kOgNZb/R1V0j6SdELyoMalFPjAscTgdmwYMnry+vcjOxJ+H2uUTnMKXwFf8IsBjz
EINy8oZ5jZcejmft0c2O5HN4Bt/7U5ttM3CroAdcvPT9lq2DFJL2uCABhTO/1DdY
b7uVa47FnkqxX19Ebn7fjp5r3diGYOmCPMjdC89C//rbkLB8FN61EkcSLpGY3YNm
djmCPQ+xaa3ielmBpOk3AMayFEtYW0nDMj9eWECVByadRQZ2qz9wTVXBp5CX9zg=
=E3Jt
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-04-22
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tap functions that can be used by the vsock transports to
deliver packets to vsockmon virtual network devices.
Signed-off-by: Gerard Garcia <ggarcia@deic.uab.cat>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an e-switch global knob to enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
The actual encap/decap is carried out (along with the matching and other actions)
per offloaded e-switch rules, e.g as done when offloading the TC tunnel key action.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is the NFC pull request for 4.12. We have:
- Improvements for the pn533 command queue handling and device
registration order.
- Removal of platform data for the pn544 and st21nfca drivers.
- Additional device tree options to support more trf7970a hardware options.
- Support for Sony's RC-S380P through the port100 driver.
- Removal of the obsolte nfcwilink driver.
- Headers inclusion cleanups (miscdevice.h, unaligned.h) for many drivers.
-----BEGIN PGP SIGNATURE-----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=Zy1M
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.12 pull request
This is the NFC pull request for 4.12. We have:
- Improvements for the pn533 command queue handling and device
registration order.
- Removal of platform data for the pn544 and st21nfca drivers.
- Additional device tree options to support more trf7970a hardware options.
- Support for Sony's RC-S380P through the port100 driver.
- Removal of the obsolte nfcwilink driver.
- Headers inclusion cleanups (miscdevice.h, unaligned.h) for many drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier patch 4493b81bea ("bonding: initialize work-queues during
creation of bond") moved the work-queue initialization from bond_open()
to bond_create(). However this caused the link those are created using
netlink 'create bond option' (ip link add bondX type bond); create the
new trunk without initializing work-queues. Prior to the above mentioned
change, ndo_open was in both paths and things worked correctly. The
consequence is visible in the report shared by Joe Stringer -
I've noticed that this patch breaks bonding within namespaces if
you're not careful to perform device cleanup correctly.
Here's my repro script, you can run on any net-next with this patch
and you'll start seeing some weird behaviour:
ip netns add foo
ip li add veth0 type veth peer name veth0+ netns foo
ip li add veth1 type veth peer name veth1+ netns foo
ip netns exec foo ip li add bond0 type bond
ip netns exec foo ip li set dev veth0+ master bond0
ip netns exec foo ip li set dev veth1+ master bond0
ip netns exec foo ip addr add dev bond0 192.168.0.1/24
ip netns exec foo ip li set dev bond0 up
ip li del dev veth0
ip li del dev veth1
The second to last command segfaults, last command hangs. rtnl is now
permanently locked. It's not a problem if you take bond0 down before
deleting veths, or delete bond0 before deleting veths. If you delete
either end of the veth pair as per above, either inside or outside the
namespace, it hits this problem.
Here's some kernel logs:
[ 1221.801610] bond0: Enslaving veth0+ as an active interface with an up link
[ 1224.449581] bond0: Enslaving veth1+ as an active interface with an up link
[ 1281.193863] bond0: Releasing backup interface veth0+
[ 1281.193866] bond0: the permanent HWaddr of veth0+ -
16:bf:fb:e0:b8:43 - is still in use by bond0 - set the HWaddr of
veth0+ to a different address to avoid conflicts
[ 1281.193867] ------------[ cut here ]------------
[ 1281.193873] WARNING: CPU: 0 PID: 2024 at kernel/workqueue.c:1511
__queue_delayed_work+0x13f/0x150
[ 1281.193873] Modules linked in: bonding veth openvswitch nf_nat_ipv6
nf_nat_ipv4 nf_nat autofs4 nfsd auth_rpcgss nfs_acl binfmt_misc nfs
lockd grace sunrpc fscache ppdev vmw_balloon coretemp psmouse
serio_raw vmwgfx ttm drm_kms_helper vmw_vmci netconsole parport_pc
configfs drm i2c_piix4 fb_sys_fops syscopyarea sysfillrect sysimgblt
shpchp mac_hid nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4
nf_defrag_ipv4 nf_conntrack libcrc32c lp parport hid_generic usbhid
hid mptspi mptscsih e1000 mptbase ahci libahci
[ 1281.193905] CPU: 0 PID: 2024 Comm: ip Tainted: G W
4.10.0-bisect-bond-v0.14 #37
[ 1281.193906] Hardware name: VMware, Inc. VMware Virtual
Platform/440BX Desktop Reference Platform, BIOS 6.00 09/30/2014
[ 1281.193906] Call Trace:
[ 1281.193912] dump_stack+0x63/0x89
[ 1281.193915] __warn+0xd1/0xf0
[ 1281.193917] warn_slowpath_null+0x1d/0x20
[ 1281.193918] __queue_delayed_work+0x13f/0x150
[ 1281.193920] queue_delayed_work_on+0x27/0x40
[ 1281.193929] bond_change_active_slave+0x25b/0x670 [bonding]
[ 1281.193932] ? synchronize_rcu_expedited+0x27/0x30
[ 1281.193935] __bond_release_one+0x489/0x510 [bonding]
[ 1281.193939] ? addrconf_notify+0x1b7/0xab0
[ 1281.193942] bond_netdev_event+0x2c5/0x2e0 [bonding]
[ 1281.193944] ? netconsole_netdev_event+0x124/0x190 [netconsole]
[ 1281.193947] notifier_call_chain+0x49/0x70
[ 1281.193948] raw_notifier_call_chain+0x16/0x20
[ 1281.193950] call_netdevice_notifiers_info+0x35/0x60
[ 1281.193951] rollback_registered_many+0x23b/0x3e0
[ 1281.193953] unregister_netdevice_many+0x24/0xd0
[ 1281.193955] rtnl_delete_link+0x3c/0x50
[ 1281.193956] rtnl_dellink+0x8d/0x1b0
[ 1281.193960] rtnetlink_rcv_msg+0x95/0x220
[ 1281.193962] ? __kmalloc_node_track_caller+0x35/0x280
[ 1281.193964] ? __netlink_lookup+0xf1/0x110
[ 1281.193966] ? rtnl_newlink+0x830/0x830
[ 1281.193967] netlink_rcv_skb+0xa7/0xc0
[ 1281.193969] rtnetlink_rcv+0x28/0x30
[ 1281.193970] netlink_unicast+0x15b/0x210
[ 1281.193971] netlink_sendmsg+0x319/0x390
[ 1281.193974] sock_sendmsg+0x38/0x50
[ 1281.193975] ___sys_sendmsg+0x25c/0x270
[ 1281.193978] ? mem_cgroup_commit_charge+0x76/0xf0
[ 1281.193981] ? page_add_new_anon_rmap+0x89/0xc0
[ 1281.193984] ? lru_cache_add_active_or_unevictable+0x35/0xb0
[ 1281.193985] ? __handle_mm_fault+0x4e9/0x1170
[ 1281.193987] __sys_sendmsg+0x45/0x80
[ 1281.193989] SyS_sendmsg+0x12/0x20
[ 1281.193991] do_syscall_64+0x6e/0x180
[ 1281.193993] entry_SYSCALL64_slow_path+0x25/0x25
[ 1281.193995] RIP: 0033:0x7f6ec122f5a0
[ 1281.193995] RSP: 002b:00007ffe69e89c48 EFLAGS: 00000246 ORIG_RAX:
000000000000002e
[ 1281.193997] RAX: ffffffffffffffda RBX: 00007ffe69e8dd60 RCX: 00007f6ec122f5a0
[ 1281.193997] RDX: 0000000000000000 RSI: 00007ffe69e89c90 RDI: 0000000000000003
[ 1281.193998] RBP: 00007ffe69e89c90 R08: 0000000000000000 R09: 0000000000000003
[ 1281.193999] R10: 00007ffe69e89a10 R11: 0000000000000246 R12: 0000000058f14b9f
[ 1281.193999] R13: 0000000000000000 R14: 00000000006473a0 R15: 00007ffe69e8e450
[ 1281.194001] ---[ end trace 713a77486cbfbfa3 ]---
Fixes: 4493b81bea ("bonding: initialize work-queues during creation of bond")
Reported-by: Joe Stringer <joe@ovn.org>
Tested-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-04-20
This adds the basic infrastructure for IPsec hardware
offloading, it creates a configuration API and adjusts
the packet path.
1) Add the needed netdev features to configure IPsec offloads.
2) Add the IPsec hardware offloading API.
3) Prepare the ESP packet path for hardware offloading.
4) Add gso handlers for esp4 and esp6, this implements
the software fallback for GSO packets.
5) Add xfrm replay handler functions for offloading.
6) Change ESP to use a synchronous crypto algorithm on
offloading, we don't have the option for asynchronous
returns when we handle IPsec at layer2.
7) Add a xfrm validate function to validate_xmit_skb. This
implements the software fallback for non GSO packets.
8) Set the inner_network and inner_transport members of
the SKB, as well as encapsulation, to reflect the actual
positions of these headers, and removes them only once
encryption is done on the payload.
From Ilan Tayari.
9) Prepare the ESP GRO codepath for hardware offloading.
10) Fix incorrect null pointer check in esp6.
From Colin Ian King.
11) Fix for the GSO software fallback path to detect the
fallback correctly.
From Ilan Tayari.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We could have a race condition where in ->classify() path we
dereference tp->root and meanwhile a parallel ->destroy() makes it
a NULL. Daniel cured this bug in commit d936377414
("net, sched: respect rcu grace period on cls destruction").
This happens when ->destroy() is called for deleting a filter to
check if we are the last one in tp, this tp is still linked and
visible at that time. The root cause of this problem is the semantic
of ->destroy(), it does two things (for non-force case):
1) check if tp is empty
2) if tp is empty we could really destroy it
and its caller, if cares, needs to check its return value to see if it
is really destroyed. Therefore we can't unlink tp unless we know it is
empty.
As suggested by Daniel, we could actually move the test logic to ->delete()
so that we can safely unlink tp after ->delete() tells us the last one is
just deleted and before ->destroy().
Fixes: 1e052be69d ("net_sched: destroy proto tp when all filters are gone")
Cc: Roi Dayan <roid@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the administrator to set an fwmark for
packets traversing a tunnel. This allows the use of independent
routing tables for tunneled packets without the use of iptables.
There is no concept of per-packet routing decisions through IPv4
tunnels, so this implementation does not need to work with
per-packet route lookups as the v6 implementation may
(with IP6_TNL_F_USE_ORIG_FWMARK).
Further, since the v4 tunnel ioctls share datastructures
(which can not be trivially modified) with the kernel's internal
tunnel configuration structures, the mark attribute must be stored
in the tunnel structure itself and passed as a parameter when
creating or changing tunnel attributes.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the administrator to set an fwmark for
packets traversing a tunnel. This allows the use of independent
routing tables for tunneled packets without the use of iptables.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only "cache" needs to use ulong (its used with set_bit()), missed can use
u16. Also add build-time assertion to ensure event bits fit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If insertion of a new conntrack fails because the table is full, the kernel
searches the next buckets of the hash slot where the new connection
was supposed to be inserted at for an entry that hasn't seen traffic
in reply direction (non-assured), if it finds one, that entry is
is dropped and the new connection entry is allocated.
Allow the conntrack gc worker to also remove *assured* conntracks if
resources are low.
Do this by querying the l4 tracker, e.g. tcp connections are now dropped
if they are no longer established (e.g. in finwait).
This could be refined further, e.g. by adding 'soft' established timeout
(i.e., a timeout that is only used once we get close to resource
exhaustion).
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
commit 223b02d923
("netfilter: nf_conntrack: reserve two bytes for nf_ct_ext->len")
had to increase size of the extension offsets because total size of the
extensions had increased to a point where u8 did overflow.
3 years later we've managed to diet extensions a bit and we no longer
need u16. Furthermore we can now add a compile-time assertion for this
problem.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
get rid of the (now unused) nf_ct_ext_add_length define and also
rename the function to plain nf_ct_ext_add().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to track this for inkernel helpers anymore as
NF_CT_HELPER_BUILD_BUG_ON checks do this now.
All inkernel helpers know what kind of structure they
stored in helper->data.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
add a 32 byte scratch area in the helper struct instead of relying
on variable sized helpers plus compile-time asserts to let us know
if 32 bytes aren't enough anymore.
Not having variable sized helpers will later allow to add BUILD_BUG_ON
for the total size of conntrack extensions -- the helper extension is
the only one that doesn't have a fixed size.
The (useless!) NF_CT_HELPER_BUILD_BUG_ON(0); are added so that in case
someone adds a new helper and copy-pastes from one that doesn't store
private data at least some indication that this macro should be used
somehow is there...
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A group of Linux kernel hackers reported chasing a bug that resulted
from their assumption that SLAB_DESTROY_BY_RCU provided an existence
guarantee, that is, that no block from such a slab would be reallocated
during an RCU read-side critical section. Of course, that is not the
case. Instead, SLAB_DESTROY_BY_RCU only prevents freeing of an entire
slab of blocks.
However, there is a phrase for this, namely "type safety". This commit
therefore renames SLAB_DESTROY_BY_RCU to SLAB_TYPESAFE_BY_RCU in order
to avoid future instances of this sort of confusion.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <linux-mm@kvack.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
[ paulmck: Add comments mentioning the old name, as requested by Eric
Dumazet, in order to help people familiar with the old name find
the new one. ]
Acked-by: David Rientjes <rientjes@google.com>
Now sctp stream reconf will process a request again even if it's seqno is
less than asoc->strreset_inseq.
If one request has been done successfully and some data chunks have been
accepted and then a duplicated strreset out request comes, the streamin's
ssn will be cleared. It will cause that stream will never receive chunks
any more because of unsynchronized ssn. It allows a replay attack.
A similar issue also exists when processing addstrm out requests. It will
cause more extra streams being added.
This patch is to fix it by saving the last 2 results into asoc. When a
duplicated strreset out or addstrm out request is received, reply it with
bad seqno if it's seqno < asoc->strreset_inseq - 2, and reply it with the
result saved in asoc if it's seqno >= asoc->strreset_inseq - 2.
Note that it saves last 2 results instead of only last 1 result, because
two requests can be sent together in one chunk.
And note that when receiving a duplicated request, the receiver side will
still reply it even if the peer has received the response. It's safe, As
the response will be dropped by the peer.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For multi-scheduled scan support in subsequent patch a request id
will be added. This patch add this request id to the scheduled
scan event messages. For now the request id will always be zero.
With multi-scheduled scan its value will inform user-space to which
scan the event relates.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add netlink_ext_ack arg to rtnl_doit_func. Pass extack arg to nlmsg_parse
for doit functions that call it directly.
This is the first step to using extended error reporting in rtnetlink.
>From here individual subsystems can be updated to set netlink_ext_ack as
needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-04-14
Here's the main batch of Bluetooth & 802.15.4 patches for the 4.12
kernel.
- Many fixes to 6LoWPAN, in particular for BLE
- New CA8210 IEEE 802.15.4 device driver (accounting for most of the
lines of code added in this pull request)
- Added Nokia Bluetooth (UART) HCI driver
- Some serdev & TTY changes that are dependencies for the Nokia
driver (with acks from relevant maintainers and an agreement that
these come through the bluetooth tree)
- Support for new Intel Bluetooth device
- Various other minor cleanups/fixes here and there
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves as is the legacy DSA code from dsa.c to legacy.c,
except the few shared symbols which remain in dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is now obsolete and always returns false.
This change has no effect on generated code.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
resurrect an old patch from Pablo Neira to remove the untracked objects.
Currently, there are four possible states of an skb wrt. conntrack.
1. No conntrack attached, ct is NULL.
2. Normal (kmem cache allocated) ct attached.
3. a template (kmalloc'd), not in any hash tables at any point in time
4. the 'untracked' conntrack, a percpu nf_conn object, tagged via
IPS_UNTRACKED_BIT in ct->status.
Untracked is supposed to be identical to case 1. It exists only
so users can check
-m conntrack --ctstate UNTRACKED vs.
-m conntrack --ctstate INVALID
e.g. attempts to set connmark on INVALID or UNTRACKED conntracks is
supposed to be a no-op.
Thus currently we need to check
ct == NULL || nf_ct_is_untracked(ct)
in a lot of places in order to avoid altering untracked objects.
The other consequence of the percpu untracked object is that all
-j NOTRACK (and, later, kfree_skb of such skbs) result in an atomic op
(inc/dec the untracked conntracks refcount).
This adds a new kernel-private ctinfo state, IP_CT_UNTRACKED, to
make the distinction instead.
The (few) places that care about packet invalid (ct is NULL) vs.
packet untracked now need to test ct == NULL vs. ctinfo == IP_CT_UNTRACKED,
but all other places can omit the nf_ct_is_untracked() check.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we do IPsec offloading, we need a fallback for
packets that were targeted to be IPsec offloaded but
rerouted to a device that does not support IPsec offload.
For that we add a function that checks the offloading
features of the sending device and and flags the
requirement of a fallback before it calls the IPsec
output function. The IPsec output function adds the IPsec
trailer and does encryption if needed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need a fallback for ESP at layer 2, so split esp6_output
into generic functions that can be used at layer 3 and layer 2
and use them in esp_output. We also add esp6_xmit which is
used for the layer 2 fallback.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need a fallback for ESP at layer 2, so split esp_output
into generic functions that can be used at layer 3 and layer 2
and use them in esp_output. We also add esp_xmit which is
used for the layer 2 fallback.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds all the bits that are needed to do
IPsec hardware offload for IPsec states and ESP packets.
We add xfrmdev_ops to the net_device. xfrmdev_ops has
function pointers that are needed to manage the xfrm
states in the hardware and to do a per packet
offloading decision.
Joint work with:
Ilan Tayari <ilant@mellanox.com>
Guy Shapiro <guysh@mellanox.com>
Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds a gso_segment and xmit callback for the
xfrm_mode and implement these functions for tunnel and
transport mode.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We add a struct xfrm_type_offload so that we have the offloaded
codepath separated to the non offloaded codepath. With this the
non offloade and the offloaded codepath can coexist.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the extended ACK reporting struct down from generic netlink to
the families, using the existing struct genl_info for simplicity.
Also add support to set the extended ACK information from generic
netlink users.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the base infrastructure and UAPI for netlink extended ACK
reporting. All "manual" calls to netlink_ack() pass NULL for now and
thus don't get extended ACK reporting.
Big thanks goes to Pablo Neira Ayuso for not only bringing up the
whole topic at netconf (again) but also coming up with the nlattr
passing trick and various other ideas.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Don't get the metric RTAX_ADVMSS of dst.
There are two reasons.
1) Its caller dst_metric_advmss has already invoke dst_metric_advmss
before invoke default_advmss.
2) The ipv4_default_advmss is used to get the default mss, it should
not try to get the metric like ip6_default_advmss.
2. Use sizeof(tcphdr)+sizeof(iphdr) instead of literal 40.
3. Define one new macro IPV4_MAX_PMTU instead of 65535 according to
RFC 2675, section 5.1.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing monitor parameters, not setting the MU-MIMO attributes
should mean that they're not changed - it's documented that to turn
the feature off it's necessary to set all-zero group membership and
an invalid follow-address. This isn't implemented.
Fix this by making the parameters pointers, stop reusing the macaddr
struct member, and documenting that NULL pointers mean unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix issue found during L2CAP qualification test TP/LE/CFC/BV-20-C.
Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to RFC 7668 U/L bit shall not be used:
https://wiki.tools.ietf.org/html/rfc7668#section-3.2.2 [Page 10]:
In the figure, letter 'b' represents a bit from the
Bluetooth device address, copied as is without any changes on any
bit. This means that no bit in the IID indicates whether the
underlying Bluetooth device address is public or random.
|0 1|1 3|3 4|4 6|
|0 5|6 1|2 7|8 3|
+----------------+----------------+----------------+----------------+
|bbbbbbbbbbbbbbbb|bbbbbbbb11111111|11111110bbbbbbbb|bbbbbbbbbbbbbbbb|
+----------------+----------------+----------------+----------------+
Because of this the code cannot figure out the address type from the IP
address anymore thus it makes no sense to use peer_lookup_ba as it needs
the peer address type.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This allow technologies such as Bluetooth to use its native lladdr which
is eui48 instead of eui64 which was expected by functions like
lowpan_header_decompress and lowpan_header_compress.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-04-11
1) Remove unused field from struct xfrm_mgr.
2) Code size optimizations for the xfrm prefix hash and
address match.
3) Branch optimization for addr4_match.
All patches from Alexey Dobriyan.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two nf_conntrack_l4proto_udp4 declarations in the head file
nf_conntrack_ipv4/6.h. Now remove one which is not enbraced by the macro
CONFIG_NF_CT_PROTO_UDPLITE.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
All DSA tag receive functions do strictly the same thing after they have located
the originating source port from their tag specific protocol:
- push ETH_HLEN bytes
- set pkt_type to PACKET_HOST
- call eth_type_trans()
- bump up counters
- call netif_receive_skb()
Factor all of that into dsa_switch_rcv(). This also makes us return a pointer to
a sk_buff, which makes us symetric with the xmit function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=JnXV
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20170406' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Miscellany
Here's a set of patches that make some minor changes to AF_RXRPC:
(1) Store error codes in struct rxrpc_call::error as negative codes and
only convert to positive in recvmsg() to avoid confusion inside the
kernel.
(2) Note the result of trying to abort a call (this fails if the call is
already 'completed').
(3) Don't abort on temporary errors whilst processing challenge and
response packets, but rather drop the packet and wait for
retransmission.
And also adds some more tracing:
(4) Protocol errors.
(5) Received abort packets.
(6) Changes in the Rx window size due to ACK packet information.
(7) Client call initiation (to allow the rxrpc_call struct pointer, the
wire call ID and the user ID/afs_call pointer to be cross-referenced).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c7e2b9689e "sched: introduce vlan action" added both the
UAPI values for the vlan actions (TCA_VLAN_ACT_) and these two
in-kernel ones which are not used, remove them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_nat_mangle_{udp,tcp}_packet() returns int. However, it is used as
bool type in many spots. Fix this by consistently handle this return
value as a boolean.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When remove one expect, it needs three statements. And there are
multiple duplicated codes in current code. So add one common function
nf_ct_remove_expect to consolidate this.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Because the type of expecting, the member of nf_conn_help, is u8, it
would overflow after reach U8_MAX(255). So it doesn't work when we
configure the max_expected exceeds 255 with expect policy.
Now add the check for max_expected. Return the -EINVAL when it exceeds
the limit.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rxrpc_kernel_abort_call() return an indication as to whether it
actually aborted the operation or not so that kafs can trace the failure of
the operation. Note that 'success' in this context means changing the
state of the call, not necessarily successfully transmitting an ABORT
packet.
Signed-off-by: David Howells <dhowells@redhat.com>
People are using bonding over Infiniband IPoIB connections, and who knows
what else. Infiniband has a hardware address length of 20 octets
(INFINIBAND_ALEN), and the network core defines a MAX_ADDR_LEN of 32.
Various places in the bonding code are currently hard-wired to 6 octets
(ETH_ALEN), such as the 3ad code, which I've left untouched here. Besides,
only alb is currently possible on Infiniband links right now anyway, due
to commit 1533e77315, so the alb code is where most of the changes are.
One major component of this change is the addition of a bond_hw_addr_copy
function that takes a length argument, instead of using ether_addr_copy
everywhere that hardware addresses need to be copied about. The other
major component of this change is converting the bonding code from using
struct sockaddr for address storage to struct sockaddr_storage, as the
former has an address storage space of only 14, while the latter is 128
minus a few, which is necessary to support bonding over device with up to
MAX_ADDR_LEN octet hardware addresses. Additionally, this probably fixes
up some memory corruption issues with the current code, where it's
possible to write an infiniband hardware address into a sockaddr declared
on the stack.
Lightly tested on a dual mlx4 IPoIB setup, which properly shows a 20-octet
hardware address now:
$ cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: fault-tolerance (active-backup) (fail_over_mac active)
Primary Slave: mlx4_ib0 (primary_reselect always)
Currently Active Slave: mlx4_ib0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 100
Down Delay (ms): 100
Slave Interface: mlx4_ib0
MII Status: up
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr:
80:00:02:08:fe:80:00:00:00:00:00:00:e4:1d:2d:03:00:1d:67:01
Slave queue ID: 0
Slave Interface: mlx4_ib1
MII Status: up
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr:
80:00:02:09:fe:80:00:00:00:00:00:01:e4:1d:2d:03:00:1d:67:02
Slave queue ID: 0
Also tested with a standard 1Gbps NIC bonding setup (with a mix of
e1000 and e1000e cards), running LNST's bonding tests.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAljjveoTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9tSZB/9DPsUOEbLzcJZ6HVRPJ3mJkCYf9jdD
VE7vW3w79EcmcbkE7ULkyrEr/+GJs7GvA1vS+j8jphraVGOjP4DjeOm1OLJXylqa
m2vaBpOqTOx3MdMdd/FVLlap7MKTX3f9J1WAOsGi5kJK3RR9EHRj5tKhoeG40OUk
rMDg9juskT+XVqgawrcHyM/eVHZ4ny+BlN2LN0zajHT6l3xKiqQ+0iQltXnstymW
djTfqlrbL+Ix6mlYKsK+joVWwbNUxuguto2m2CKVQukWFu2Q5wxe5YASjtMThQcv
vmq2LD45cFIfNhzgfTu2msoz2Cv613LFiMtHtrfjlbXtSZmFc2FqIbKc
=NjgL
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.13-20170404' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-03-03
this is a pull request of 5 patches for net-next/master.
There are two patches by Yegor Yefremov which convert the ti_hecc
driver into a DT only driver, as there is no in-tree user of the old
platform driver interface anymore. The next patch by Mario Kicherer
adds network namespace support to the can subsystem. The last two
patches by Akshay Bhat add support for the holt_hi311x SPI CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define one new macro TCP_MAX_WSCALE instead of literal number '14',
and use U16_MAX instead of 65535 as the max value of TCP window.
There is another minor change, use rounddown(space, mss) instead of
(space / mss) * mss;
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is almost to revert commit 02f3d4ce9e ("sctp: Adjust PMTU
updates to accomodate route invalidation."). As t->asoc can't be NULL
in sctp_transport_update_pmtu, it could get sk from asoc, and no need
to pass sk into that function.
It is also to remove some duplicated codes from that function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases nfc_dbg() is useful. Add such macro to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds initial support for network namespaces. The changes only
enable support in the CAN raw, proc and af_can code. GW and BCM still
have their checks that ensure that they are used only from the main
namespace.
The patch boils down to moving the global structures, i.e. the global
filter list and their /proc stats, into a per-namespace structure and passing
around the corresponding "struct net" in a lot of different places.
Changes since v1:
- rebased on current HEAD (2bfe01e)
- fixed overlong line
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make ->hash_count, ->low_watermark and ->high_watermark unsigned int
and propagate unsignedness to other variables.
This change doesn't change code generation because these fields aren't
used in 64-bit contexts but make it anyway: these fields can't be
negative numbers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow keys aren't 4GB+ numbers so 64-bit arithmetic is excessive.
Space savings (I'm not sure what CSWTCH is):
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-48 (-48)
function old new delta
flow_cache_lookup 1163 1159 -4
CSWTCH 75997 75953 -44
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move sctp_transport_dst_check into sctp_packet_config
from sctp_packet_transmit and add pathmtu check in sctp_packet_config.
With this fix, sctp can update dst or pathmtu before appending chunks,
which can void dropping packets in sctp_packet_transmit when dst is
obsolete or dst's mtu is changed.
This patch is also to improve some other codes in sctp_packet_config.
It updates packet max_size with gso_max_size, checks for dst and
pathmtu, and appends ecne chunk only when packet is empty and asoc
is not NULL.
It makes sctp flush work better, as we only need to set up them once
for one flush schedule. It's also safe, since asoc is NULL only when
the packet is created by sctp_ootb_pkt_new in which it just gets the
new dst, no need to do more things for it other than set packet with
transport's pathmtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before when implementing sctp prsctp, SCTP_PR_STREAM_STATUS wasn't
added, as it needs to save abandoned_(un)sent for every stream.
After sctp stream reconf is added in sctp, assoc has structure
sctp_stream_out to save per stream info.
This patch is to add SCTP_PR_STREAM_STATUS by putting the prsctp
per stream statistics into sctp_stream_out.
v1->v2:
fix an indent issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems the code does not match the intent.
This broke packetdrill, and probably other programs.
Fixes: 6c7c98bad4 ("sock: avoid dirtying sk_stamp, if possible")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alow users to push down more labels per MPLS encap. Similar to LSR case,
move label array to the end of mpls_iptunnel_encap and allocate based on
the number of labels for the route.
For consistency with the LSR case, re-use the same maximum number of
labels.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce crosschip_bridge_{join,leave} operations in the dsa_switch_ops
structure, which can be used by switches supporting interconnection.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance nl80211 and cfg80211 connect request and response APIs to
support FILS shared key authentication offload. The new nl80211
attributes can be used to provide additional information to the driver
to establish a FILS connection. Also enhance the set/del PMKSA to allow
support for adding and deleting PMKSA based on FILS cache identifier.
Add a new feature flag that drivers can use to advertize support for
FILS shared key authentication and association in station mode when
using their own SME.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the connect event from driver takes all the connection
response parameters as arguments. With support for new features these
response parameters can grow. Use a structure to pass these parameters
rather than passing them as function arguments.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add to documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sock_recv_ts_and_drops() unconditionally set sk->sk_stamp for
every packet, even if the SOCK_TIMESTAMP flag is not set in the
related socket.
If selinux is enabled, this cause a cache miss for every packet
since sk->sk_stamp and sk->sk_security share the same cacheline.
With this change sk_stamp is set only if the SOCK_TIMESTAMP
flag is set, and is cleared for the first packet, so that the user
perceived behavior is unchanged.
This gives up to 5% speed-up under udp-flood with small packets.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a msg without asoc established, sctp will send INIT packet
first and then enqueue chunks.
Before receiving INIT_ACK, stream info is not yet alloced. But enqueuing
chunks needs to access stream info, like out stream state and out stream
cnt.
This patch is to fix it by allocing out stream info when initializing an
asoc, allocing in stream and re-allocing out stream when processing init.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.
The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.
One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.
Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.
The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.
The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.
Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.
Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
- Or.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY2lwEAAoJEEg/ir3gV/o+rFIH+wdwGawEjoDhpihLqJHoRtwo
Wvy88Lczj++Pfzt9E0kgwgmOdnj7j+GVOh6ALjneE3PDBJEFWG/GWY5aRYonlhhf
zibafMTYf+8Dmm9qHW/C4OvhQowSrkG1RDucM2eyjXJfnAShZCh7dV4CDD7paxhu
N2rlDdSEl0Im4aPCNHzyrdGg06Fy3A0DQkDvVLIQhKV0cLPIoC0U/i+ymVtsCUY/
sSEEuSohvwdD5Ga5ZZdKicCo61lIRSi2rX5v4sK0exhAO3S8xyrKnwbiN7nVAQqg
eVZ/ekbBiksD8MRMKctt/zGxd0X4PDaQ8J9XyF9CL6pRC5VipsDy+P/GEhj/x8U=
=l2Qo
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-pedit' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Or Gerlitz says:
====================
mlx5e-pedit 2017-03-28
This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.
The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.
One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.
Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.
The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.
The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.
Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.
Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor inet6_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for NETDEV_RESEND_IGMP event similar
to how it works for IPv4.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Laight noticed the support for MSG_MORE with datamsg->force_delay
didn't really work as we expected, as the first msg with MSG_MORE set
would always block the following chunks' dequeuing.
This Patch is to rewrite it by saving the MSG_MORE flag into assoc as
David Laight suggested.
asoc->force_delay is used to save MSG_MORE flag before a msg is sent.
All chunks in queue would not be sent out if asoc->force_delay is set
by the msg with MSG_MORE flag, until a new msg without MSG_MORE flag
clears asoc->force_delay.
Note that this change would not affect the flush is generated by other
triggers, like asoc->state != ESTABLISHED, queue size > pmtu etc.
v1->v2:
Not clear asoc->force_delay after sending the msg with MSG_MORE flag.
Fixes: 4ea0c32f5f ("sctp: add support for MSG_MORE")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Laight <david.laight@aculab.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pipeline debug is used to export the pipeline abstractions for the
main objects - tables, headers and entries. The only support for set is
for changing the counter parameter on specific table.
The basic structures:
Header - can represent a real protocol header information or internal
metadata. Generic protocol headers like IPv4 can be shared
between drivers. Each driver can add local headers.
Field - part of a header. Can represent protocol field or specific ASIC
metadata field. Hardware special metadata fields can be mapped
to different resources, for example switch ASIC ports can have
internal number which from the systems point of view is mapped
to netdeivce ifindex.
Match - represent specific match rule. Can describe match on specific
field or header. The header index should be specified as well
in order to support several header instances of the same type
(tunneling).
Action - represents specific action rule. Actions can describe operations
on specific field values for example like set, increment, etc.
And header operation like add and delete.
Value - represents value which can be associated with specific match or
action.
Table - represents a hardware block which can be described with match/
action behavior. The match/action can be done on the packets
data or on the internal metadata that it gathered along the
packets traversal throw the pipeline which is vendor specific
and should be exported in order to provide understanding of
ASICs behavior.
Entry - represents single record in a specific table. The entry is
identified by specific combination of values for match/action.
Prior to accessing the tables/entries the drivers provide the header/
field data base which is used by driver to user-space. The data base
is split between the shared headers and unique headers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW drivers will use the header-type and command fields from the extended
keys, and some fields (e.g mask, val, offset) from the legacy keys.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Split the function into two (a) propose (b) commit phase without
changing the semantics for the original API.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current addr4_match() code has special test for /0 prefixes because of
standard required undefined behaviour. However, it is possible to omit
it on 64-bit because shifting can be done within a 64-bit register and
then truncated to the expected value (which is 0 mask).
Implicit truncation by htonl() fits nicely into R32-within-R64 model
on x86-64.
Space savings: none (coincidence)
Branch savings: 1
Before:
movzx eax,BYTE PTR [rdi+0x2a] # ->prefixlen_d
test al,al
jne xfrm_selector_match + 0x23f
...
movzx eax,BYTE PTR [rbx+0x2b] # ->prefixlen_s
test al,al
je xfrm_selector_match + 0x1c7
After (no branches):
mov r8d,0x20
mov rdx,0xffffffffffffffff
mov esi,DWORD PTR [rsi+0x2c]
mov ecx,r8d
sub cl,BYTE PTR [rdi+0x2a]
xor esi,DWORD PTR [rbx]
mov rdi,rdx
xor eax,eax
shl rdi,cl
bswap edi
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Move the core functionality in sk_busy_loop() to napi_busy_loop() and
make it independent of sk.
This enables re-using this function in epoll busy loop implementation.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch flips the logic we were using to determine if the busy polling
has timed out. The main motivation for this is that we will need to
support two different possible timeout values in the future and by
recording the start time rather than when we would want to end we can focus
on making the end_time specific to the task be it epoll or socket based
polling.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checking the return value of sk_busy_loop. As there are only a few
consumers of that data, and the data being checked for can be replaced
with a check for !skb_queue_empty() we might as well just pull the code
out of sk_busy_loop and place it in the spots that actually need it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of defining two versions of skb_mark_napi_id I think it is more
readable to just match the format of the sk_mark_napi_id functions and just
wrap the contents of the function instead of defining two versions of the
function. This way we can save a few lines of code since we only need 2 of
the ifdef/endif but needed 5 for the extra function declaration.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a cleanup/fix for NAPI IDs following the changes that made it
so that sender_cpu and napi_id were doing a better job of sharing the same
location in the sk_buff.
One issue I found is that we weren't validating the napi_id as being valid
before we started trying to setup the busy polling. This change corrects
that by using the MIN_NAPI_ID value that is now used in both allocating the
NAPI IDs, as well as validating them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because sysctl_tcp_adv_win_scale could be changed any time, so there
is one race in tcp_win_from_space.
For example,
1.sysctl_tcp_adv_win_scale<=0 (sysctl_tcp_adv_win_scale is negative now)
2.space>>(-sysctl_tcp_adv_win_scale) (sysctl_tcp_adv_win_scale is postive now)
As a result, tcp_win_from_space returns 0. It is unexpected.
Certainly if the compiler put the sysctl_tcp_adv_win_scale into one
register firstly, then use the register directly, it would be ok.
But we could not depend on the compiler behavior.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain system process significant unconnected UDP workload.
It would be preferrable to disable UDP early demux for those systems
and enable it for TCP only.
By disabling UDP demux, we see these slight gains on an ARM64 system-
782 -> 788Mbps unconnected single stream UDPv4
633 -> 654Mbps unconnected UDPv4 different sources
The performance impact can change based on CPU architecure and cache
sizes. There will not much difference seen if entire UDP hash table
is in cache.
Both sysctls are enabled by default to preserve existing behavior.
v1->v2: Change function pointer instead of adding conditional as
suggested by Stephen.
v2->v3: Read once in callers to avoid issues due to compiler
optimizations. Also update commit message with the tests.
v3->v4: Store and use read once result instead of querying pointer
again incorrectly.
v4->v5: Refactor to avoid errors due to compilation with IPV6={m,n}
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Suggested-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Tom Herbert <tom@herbertland.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
x86_64 is zero-extending arch so "unsigned int" is preferred over "int"
for address calculations and extending to size_t.
Space savings:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-24 (-24)
function old new delta
xfrm_state_walk 708 696 -12
xfrm_selector_match 918 906 -12
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows reading of SK_MEMINFO_VARS via socket option. This way an
application can get all meminfo related information in single socket
option call instead of multiple calls.
Adds helper function, sk_get_meminfo(), and uses that for both
getsockopt and sock_diag_put_meminfo().
Suggested by Eric Dumazet.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Jason Baron <jbaron@akamai.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream
is defined after it's declaration.
This patch is to declare struct sctp_stream before sctp_stream_free.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh notifications today carry pid 0 for nlmsg_pid
in all cases. This patch fixes it to carry calling process
pid when available. Applications (eg. quagga) rely on
nlmsg_pid to ignore notifications generated by their own
netlink operations. This patch follows the routing subsystem
which already sets this correctly.
Reported-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tp->dst_pending_confirm's value can only be set 0 or 1, this
patch is to change to define it as a bit instead of __u32.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ECMP hash policy choice via a new sysctl
called fib_multipath_hash_policy and also adds support for L4 hashes.
The current values for fib_multipath_hash_policy are:
0 - layer 3 (default)
1 - layer 4
If there's an skb hash already set and it matches the chosen policy then it
will be used instead of being calculated (currently only for L4).
In L3 mode we always calculate the hash due to the ICMP error special
case, the flow dissector's field consistentification should handle the
address order thus we can remove the address reversals.
If the skb is provided we always use it for the hash calculation,
otherwise we fallback to fl4, that is if skb is NULL fl4 has to be set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow canceling all packets of a connection.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your
net-next tree. A couple of new features for nf_tables, and unsorted
cleanups and incremental updates for the Netfilter tree. More
specifically, they are:
1) Allow to check for TCP option presence via nft_exthdr, patch
from Phil Sutter.
2) Add symmetric hash support to nft_hash, from Laura Garcia Liebana.
3) Use pr_cont() in ebt_log, from Joe Perches.
4) Remove some dead code in arp_tables reported via static analysis
tool, from Colin Ian King.
5) Consolidate nf_tables expression validation, from Liping Zhang.
6) Consolidate set lookup via nft_set_lookup().
7) Remove unnecessary rcu read lock side in bridge netfilter, from
Florian Westphal.
8) Remove unused variable in nf_reject_ipv4, from Tahee Yoo.
9) Pass nft_ctx struct to object initialization indirections, from
Florian Westphal.
10) Add code to integrate conntrack helper into nf_tables, also from
Florian.
11) Allow to check if interface index or name exists via
NFTA_FIB_F_PRESENT, from Phil Sutter.
12) Simplify resolve_normal_ct(), from Florian.
13) Use per-limit spinlock in nft_limit and xt_limit, from Liping Zhang.
14) Use rwlock in nft_set_rbtree set, also from Liping Zhang.
15) One patch to remove a useless printk at netns init path in ipvs,
and several patches to document IPVS knobs.
16) Use refcount_t for reference counter in the Netfilter/IPVS code,
from Elena Reshetova.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API (see include/linux/refcount.h)
should be used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The tcp_tw_recycle was already broken for connections
behind NAT, since the per-destination timestamp is not
monotonically increasing for multiple machines behind
a single destination address.
After the randomization of TCP timestamp offsets
in commit 8a5bd45f6616 (tcp: randomize tcp timestamp offsets
for each connection), the tcp_tw_recycle is broken for all
types of connections for the same reason: the timestamps
received from a single machine is not monotonically increasing,
anymore.
Remove tcp_tw_recycle, since it is not functional. Also, remove
the PAWSPassive SNMP counter since it is only used for
tcp_tw_recycle, and simplify tcp_v4_route_req and tcp_v6_route_req
since the strict argument is only set when tcp_tw_recycle is
enabled.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Lutz Vieweg <lvml@5t9.de>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8a5bd45f6616 (tcp: randomize tcp timestamp offsets for each connection)
randomizes TCP timestamps per connection. After this commit,
there is no guarantee that the timestamps received from the
same destination are monotonically increasing. As a result,
the per-destination timestamp cache in TCP metrics (i.e., tcpm_ts
in struct tcp_metrics_block) is broken and cannot be relied upon.
Remove the per-destination timestamp cache and all related code
paths.
Note that this cache was already broken for caching timestamps of
multiple machines behind a NAT sharing the same address.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Lutz Vieweg <lvml@5t9.de>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a FIB rule is added or removed, a notification is sent in the
FIB notification chain. However, listeners don't have a way to tell
which rule was added or removed.
This is problematic as we would like to give listeners the ability to
decide which action to execute based on the notified rule. Specifically,
offloading drivers should be able to determine if they support the
reflection of the notified FIB rule and flush their LPM tables in case
they don't.
Do that by adding a notifier info to these notifications and embed the
common FIB rule struct in it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when non-default (custom) FIB rules are used, devices capable
of layer 3 offloading flush their tables and let the kernel do the
forwarding instead.
When these devices' drivers are loaded they register to the FIB
notification chain, which lets them know about the existence of any
custom FIB rules. This is done by sending a RULE_ADD notification based
on the value of 'net->ipv4.fib_has_custom_rules'.
This approach is problematic when VRF offload is taken into account, as
upon the creation of the first VRF netdev, a l3mdev rule is programmed
to direct skbs to the VRF's table.
Instead of merely reading the above value and sending a single RULE_ADD
notification, we should iterate over all the FIB rules and send a
detailed notification for each, thereby allowing offloading drivers to
sanitize the rules they don't support and potentially flush their
tables.
While l3mdev rules are uniquely marked, the default rules are not.
Therefore, when they are being notified they might invoke offloading
drivers to unnecessarily flush their tables.
Solve this by adding an helper to check if a FIB rule is a default rule.
Namely, its selector should match all packets and its action should
point to the local, main or default tables.
As noted by David Ahern, uniquely marking the default rules is
insufficient. When using VRFs, it's common to avoid false hits by moving
the rule for the local table to just before the main table:
Default configuration:
$ ip rule show
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
Common configuration with VRFs:
$ ip rule show
1000: from all lookup [l3mdev-table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DSA switch driver cannot program an ageing time value due to it
being out-of-range, switchdev will raise a stack trace before failing.
To fix this, add ageing_time_min and ageing_time_max members to the
dsa_switch in order for the switch drivers to optionally specify their
supported ageing time limits.
The DSA core will now check for provided ageing time limits and return
-ERANGE from the switchdev prepare phase if the value is out-of-range.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree, a
rather large batch of fixes targeted to nf_tables, conntrack and bridge
netfilter. More specifically, they are:
1) Don't track fragmented packets if the socket option IP_NODEFRAG is set.
From Florian Westphal.
2) SCTP protocol tracker assumes that ICMP error messages contain the
checksum field, what results in packet drops. From Ying Xue.
3) Fix inconsistent handling of AH traffic from nf_tables.
4) Fix new bitmap set representation with big endian. Fix mismatches in
nf_tables due to incorrect big endian handling too. Both patches
from Liping Zhang.
5) Bridge netfilter doesn't honor maximum fragment size field, cap to
largest fragment seen. From Florian Westphal.
6) Fake conntrack entry needs to be aligned to 8 bytes since the 3 LSB
bits are now used to store the ctinfo. From Steven Rostedt.
7) Fix element comments with the bitmap set type. Revert the flush
field in the nft_set_iter structure, not required anymore after
fixing up element comments.
8) Missing error on invalid conntrack direction from nft_ct, also from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Allow TTL propagation from IP packets to MPLS packets to be
configured. Add a new optional LWT attribute, MPLS_IPTUNNEL_TTL, which
allows the TTL to be set in the resulting MPLS packet, with the value
of 0 having the semantics of enabling propagation of the TTL from the
IP header (i.e. non-zero values disable propagation).
Also allow the configuration to be overridden globally by reusing the
same sysctl to control whether the TTL is propagated from IP packets
into the MPLS header. If the per-LWT attribute is set then it
overrides the global configuration. If the TTL isn't propagated then a
default TTL value is used which can be configured via a new sysctl,
"net.mpls.default_ttl". This is kept separate from the configuration
of whether IP TTL propagation is enabled as it can be used in the
future when non-IP payloads are supported (i.e. where there is no
payload TTL that can be propagated).
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide the ability to control on a per-route basis whether the TTL
value from an MPLS packet is propagated to an IPv4/IPv6 packet when
the last label is popped as per the theoretical model in RFC 3443
through a new route attribute, RTA_TTL_PROPAGATE which can be 0 to
mean disable propagation and 1 to mean enable propagation.
In order to provide the ability to change the behaviour for packets
arriving with IPv4/IPv6 Explicit Null labels and to provide an easy
way for a user to change the behaviour for all existing routes without
having to reprogram them, a global knob is provided. This is done
through the addition of a new per-namespace sysctl,
"net.mpls.ip_ttl_propagate", which defaults to enabled. If the
per-route attribute is set (either enabled or disabled) then it
overrides the global configuration.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1f48ff6c53.
This patch is not required anymore now that we keep a dummy list of
set elements in the bitmap set implementation, so revert this before
we forget this code has no clients.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of the actual interface index or name, set destination register
to just 1 or 0 depending on whether the lookup succeeded or not if
NFTA_FIB_F_PRESENT was set in userspace.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
this is needed by the upcoming ct helper object type --
we'd like to be able use the table family (ip, ip6, inet) to figure
out which helper has to be requested.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since the nfct and nfctinfo have been combined, the nf_conn structure
must be at least 8 bytes aligned, as the 3 LSB bits are used for the
nfctinfo. But there's a fake nf_conn structure to denote untracked
connections, which is created by a PER_CPU construct. This does not
guarantee that it will be 8 bytes aligned and can break the logic in
determining the correct nfctinfo.
I triggered this on a 32bit machine with the following error:
BUG: unable to handle kernel NULL pointer dereference at 00000af4
IP: nf_ct_deliver_cached_events+0x1b/0xfb
*pdpt = 0000000031962001 *pde = 0000000000000000
Oops: 0000 [#1] SMP
[Modules linked in: ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipv6 crc_ccitt ppdev r8169 parport_pc parport
OK ]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-test+ #75
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
task: c126ec00 task.stack: c1258000
EIP: nf_ct_deliver_cached_events+0x1b/0xfb
EFLAGS: 00010202 CPU: 0
EAX: 0021cd01 EBX: 00000000 ECX: 27b0c767 EDX: 32bcb17a
ESI: f34135c0 EDI: f34135c0 EBP: f2debd60 ESP: f2debd3c
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000af4 CR3: 309a0440 CR4: 001406f0
Call Trace:
<SOFTIRQ>
? ipv6_skip_exthdr+0xac/0xcb
ipv6_confirm+0x10c/0x119 [nf_conntrack_ipv6]
nf_hook_slow+0x22/0xc7
nf_hook+0x9a/0xad [ipv6]
? ip6t_do_table+0x356/0x379 [ip6_tables]
? ip6_fragment+0x9e9/0x9e9 [ipv6]
ip6_output+0xee/0x107 [ipv6]
? ip6_fragment+0x9e9/0x9e9 [ipv6]
dst_output+0x36/0x4d [ipv6]
NF_HOOK.constprop.37+0xb2/0xba [ipv6]
? icmp6_dst_alloc+0x2c/0xfd [ipv6]
? local_bh_enable+0x14/0x14 [ipv6]
mld_sendpack+0x1c5/0x281 [ipv6]
? mark_held_locks+0x40/0x5c
mld_ifc_timer_expire+0x1f6/0x21e [ipv6]
call_timer_fn+0x135/0x283
? detach_if_pending+0x55/0x55
? mld_dad_timer_expire+0x3e/0x3e [ipv6]
__run_timers+0x111/0x14b
? mld_dad_timer_expire+0x3e/0x3e [ipv6]
run_timer_softirq+0x1c/0x36
__do_softirq+0x185/0x37c
? test_ti_thread_flag.constprop.19+0xd/0xd
do_softirq_own_stack+0x22/0x28
</SOFTIRQ>
irq_exit+0x5a/0xa4
smp_apic_timer_interrupt+0x2a/0x34
apic_timer_interrupt+0x37/0x3c
By using DEFINE/DECLARE_PER_CPU_ALIGNED we can enforce at least 8 byte
alignment as all cache line sizes are at least 8 bytes or more.
Fixes: a9e419dc7b ("netfilter: merge ctinfo into nfct pointer storage area")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, there are two different methods to store an u16 integer to
the u32 data register. For example:
u32 *dest = ®s->data[priv->dreg];
1. *dest = 0; *(u16 *) dest = val_u16;
2. *dest = val_u16;
For method 1, the u16 value will be stored like this, either in
big-endian or little-endian system:
0 15 31
+-+-+-+-+-+-+-+-+-+-+-+-+
| Value | 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+
For method 2, in little-endian system, the u16 value will be the same
as listed above. But in big-endian system, the u16 value will be stored
like this:
0 15 31
+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 | Value |
+-+-+-+-+-+-+-+-+-+-+-+-+
So later we use "memcmp(®s->data[priv->sreg], data, 2);" to do
compare in nft_cmp, nft_lookup expr ..., method 2 will get the wrong
result in big-endian system, as 0~15 bits will always be zero.
For the similar reason, when loading an u16 value from the u32 data
register, we should use "*(u16 *) sreg;" instead of "(u16)*sreg;",
the 2nd method will get the wrong value in the big-endian system.
So introduce some wrapper functions to store/load an u8 or u16
integer to/from the u32 data register, and use them in the right
place.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce a dsa_is_normal_port helper to check if a given port is a
normal user port as opposed to a CPU port or DSA link.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the
Re-configuration Response Parameter in rfc6525 section 5.2.7.
sctp_process_strreset_resp would process the response for any
kind of reconf request, and the stream reconf is applied only
when the response result is success.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the Add Incoming
Streams Request Parameter described in rfc6525 section 5.2.6.
It is also to fix that it shouldn't have add streams when sending addstrm
in request, as the process in peer will handle it by sending a addstrm out
request back.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add Receiver-Side Procedures for the Add Outgoing
Streams Request Parameter described in section 5.2.5.
It is also to improve sctp_chunk_lookup_strreset_param, so that it
can be used for processing addstrm_out request.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add Stream Change Event described in rfc6525
section 6.1.3.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the SSN/TSN
Reset Request Parameter described in rfc6525 section 6.2.4.
The process is kind of complicate, it's wonth having some comments
from section 6.2.4 in the codes.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add Association Reset Event described in rfc6525
section 6.1.2.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original reason [1] for having hidden qdiscs (potential scalability
issues in qdisc_match_from_root() with single linked list in case of large
amount of qdiscs) has been invalidated by 59cc1f61f0 ("net: sched: convert
qdisc linked list to hashtable").
This allows us for bringing more clarity and determinism into the dump by
making default pfifo qdiscs visible.
We're not turning this on by default though, at it was deemed [2] too
intrusive / unnecessary change of default behavior towards userspace.
Instead, TCA_DUMP_INVISIBLE netlink attribute is introduced, which allows
applications to request complete qdisc hierarchy dump, including the
ones that have always been implicit/invisible.
Singleton noop_qdisc stays invisible, as teaching the whole infrastructure
about singletons would require quite some surgery with very little gain
(seeing no qdisc or seeing noop qdisc in the dump is probably setting
the same user expectation).
[1] http://lkml.kernel.org/r/1460732328.10638.74.camel@edumazet-glaptop3.roam.corp.google.com
[2] http://lkml.kernel.org/r/20161021.105935.1907696543877061916.davem@davemloft.net
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always pass the same event type to fib_notify() and
fib_rules_notify(), so we can safely drop this argument.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the code concerned with the FIB notification chain currently
resides in fib_trie.c, but this isn't really appropriate, as the FIB
notification chain is also used for FIB rules.
Therefore, it makes sense to move the common FIB notification code to a
separate file and have it export the relevant functions, which can be
invoked by its different users (e.g., fib_trie.c, fib_rules.c).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VLAN action offloading. Invoke it from Spectrum flower handler for
"vlan modify" actions.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions that are returning tcp sequence number also setup
TS offset value, so rename them to better describe their purpose.
No functional changes in this patch.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__sk_dst_set() must be called while we own the socket.
We can get proper lockdep coverage using lockdep_sock_is_held()
and rcu_dereference_protected()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter reports that IPv6 AH header matching is broken. From
userspace, nft generates bytecode that expects to find the AH header at
NFT_PAYLOAD_TRANSPORT_HEADER both for IPv4 and IPv6. However,
pktinfo->thoff is set to the inner header after the AH header in IPv6,
while in IPv4 pktinfo->thoff points to the AH header indeed. This
behaviour is inconsistent. This patch fixes this problem by updating
ipv6_find_hdr() to get the IP6_FH_F_AUTH flag so this function stops at
the AH header, so both IPv4 and IPv6 pktinfo->thoff point to the AH
header.
This is also inconsistent when trying to match encapsulated headers:
1) A packet that looks like IPv4 + AH + TCP dport 22 will *not* match.
2) A packet that looks like IPv6 + AH + TCP dport 22 will match.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This new function consolidates set lookup via either name or ID by
introducing a new nft_set_lookup() function. Replace existing spots
where we can use this too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211. There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the SET CQM command's RSSI threshold attribute to accept any
number of thresholds as a sorted array. The API should be backwards
compatible so that if one s32 threshold value is passed, the old
mechanism is enabled. The netlink event generated is the same in both
cases.
cfg80211 handles an arbitrary number of RSSI thresholds but drivers have
to provide a method (set_cqm_rssi_range_config) that configures a range
set by a high and a low value. Drivers have to call back when the RSSI
goes out of that range and there's no additional event for each time the
range is reconfigured as there was with the current one-threshold API.
This method doesn't have a hysteresis parameter because there's no
benefit to the cfg80211 code from having the hysteresis be handled by
hardware/driver in terms of the number of wakeups. At the same time
it would likely be less consistent between drivers if offloaded or
done in the drivers.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Pull misc final vfs updates from Al Viro:
"A few unrelated patches that got beating in -next.
Everything else will have to go into the next window ;-/"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
hfs: fix hfs_readdir()
selftest for default_file_splice_read() infoleak
9p: constify ->d_name handling
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Missing check for full sock in ip_route_me_harder(), from
Florian Westphal.
2) Incorrect sip helper structure initilization that breaks it when
several ports are used, from Christophe Leroy.
3) Fix incorrect assumption when looking up for matching with adjacent
intervals in the nft_set_rbtree.
4) Fix broken netlink event error reporting in nf_tables that results
in misleading ESRCH errors propagated to userspace listeners.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The underlying nlmsg_multicast() already sets sk->sk_err for us to
notify socket overruns, so we should not do anything with this return
value. So we just call nfnetlink_set_err() if:
1) We fail to allocate the netlink message.
or
2) We don't have enough space in the netlink message to place attributes,
which means that we likely need to allocate a larger message.
Before this patch, the internal ESRCH netlink error code was propagated
to userspace, which is quite misleading. Netlink semantics mandate that
listeners just hit ENOBUFS if the socket buffer overruns.
Reported-by: Alexander Alemayhu <alexander@alemayhu.com>
Tested-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When handling problems in cloning a socket with the sk_clone_locked()
function we need to perform several steps that were open coded in it and
its callers, so introduce a routine to avoid this duplication:
sk_free_unlock_clone().
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/net-ui6laqkotycunhtmqryl9bfx@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.
But first update code that relied on the implicit header inclusion.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add #include <linux/cred.h> dependencies to all .c files rely on sched.h
doing that for them.
Note that even if the count where we need to add extra headers seems high,
it's still a net win, because <linux/sched.h> is included in over
2,200 files ...
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
disassocation||disassociation
Link: http://lkml.kernel.org/r/1481573103-11329-27-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
an user||a user
an userspace||a userspace
I also added "userspace" to the list since it is a common word in Linux.
I found some instances for "an userfaultfd", but I did not add it to the
list. I felt it is endless to find words that start with "user" such as
"userland" etc., so must draw a line somewhere.
Link: http://lkml.kernel.org/r/1481573103-11329-4-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
This patch is to add support for MSG_MORE on sctp.
It adds force_delay in sctp_datamsg to save MSG_MORE, and sets it after
creating datamsg according to the send flag. sctp_packet_can_append_data
then uses it to decide if the chunks of this msg will be sent at once or
delay it.
Note that unlike [1], this patch saves MSG_MORE in datamsg, instead of
in assoc. As sctp enqueues the chunks first, then dequeue them one by
one. If it's saved in assoc,the current msg's send flag (MSG_MORE) may
affect other chunks' bundling.
Since last patch, sctp flush out queue once assoc state falls into
SHUTDOWN_PENDING, the close block problem mentioned in [1] has been
solved as well.
[1] https://patchwork.ozlabs.org/patch/372404/
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when sending a packet, sctp_transport_dst_check will check if dst
is obsolete by calling ipv4/ip6_dst_check. But they return obsolete
only when adding a new cache, after that when the cache's pmtu is
updated again, it will not trigger transport->dst/pmtu's update.
It can be reproduced by reducing route's pmtu twice. At the 1st time
client will add a new cache, and transport->pathmtu gets updated as
sctp_transport_dst_check finds it's obsolete. But at the 2nd time,
cache's mtu is updated, sctp client will never send out any packet,
because transport->pmtu has no chance to update.
This patch is to fix this by also checking if transport pmtu is dst
mtu in sctp_transport_dst_check, so that transport->pmtu can be
updated on time.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add reconf chunk event based on the sctp event
frame in rx path, it will call sctp_sf_do_reconf to process the
reconf chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a function to process the incoming reconf chunk,
in which it verifies the chunk, and traverses the param and process
it with the right function one by one.
sctp_sf_do_reconf would be the process function of reconf chunk event.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a function sctp_verify_reconf to do some length
check and multi-params check for sctp stream reconf according to rfc6525
section 3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the Incoming
SSN Reset Request Parameter described in rfc6525 section 5.2.3.
It's also to move str_list endian conversion out of sctp_make_strreset_req,
so that sctp_make_strreset_req can be used more conveniently to process
inreq.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the Outgoing
SSN Reset Request Parameter described in rfc6525 section 5.2.2.
Note that some checks must be after request_seq check, as even those
checks fail, strreset_inseq still has to be increase by 1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add Stream Reset Event described in rfc6525
section 6.1.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define Re-configuration Response Parameter described
in rfc6525 section 4.4. As optional fields are only for SSN/TSN Reset
Request Parameter, it uses another function to make that.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way of querying whether a filter is
offloaded to HW or not when using "both" policy (where none
of skip_sw or skip_hw flags are set by user-space).
Add two new flags, "in hw" and "not in hw" such that user
space can determine if a filter is actually offloaded to
hw or not. The "in hw" UAPI semantics was chosen so it's
similar to the "skip hw" flag logic.
If none of these two flags are set, this signals running
over older kernel.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-02-16
1) Make struct xfrm_input_afinfo const, nothing writes to it.
From Florian Westphal.
2) Remove all places that write to the afinfo policy backend
and make the struct const then.
From Florian Westphal.
3) Prepare for packet consuming gro callbacks and add
ESP GRO handlers. ESP packets can be decapsulated
at the GRO layer then. It saves a round through
the stack for each ESP packet.
Please note that this has a merge coflict between commit
63fca65d08 ("net: add confirm_neigh method to dst_ops")
from net-next and
3d7d25a68e ("xfrm: policy: remove garbage_collect callback")
a2817d8b27 ("xfrm: policy: remove family field")
from ipsec-next.
The conflict can be solved as it is done in linux-next.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes broken build for !NET_CLS:
net/built-in.o: In function `fq_codel_destroy':
/home/sab/linux/net-next/net/sched/sch_fq_codel.c:468: undefined reference to `tcf_destroy_chain'
Fixes: cf1facda2f ("sched: move tcf_proto_destroy and tcf_destroy_chain helpers into cls_api")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO ifrastructure and callbacks for ESP on
ipv4 and ipv6.
In case the GRO layer detects an ESP packet, the
esp{4,6}_gro_receive() function does a xfrm state lookup
and calls the xfrm input layer if it finds a matching state.
The packet will be decapsulated and reinjected it into layer 2.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need to keep per packet offloading informations across
the layers. So we extend the sec_path to carry these for
the input and output offload codepath.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add a new helper to set the secpath to the skb.
This avoids code duplication, as this is used
in multiple places.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 79e7fff47b ("net: remove support for per driver
ndo_busy_poll()") made them obsolete.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, most relevantly they are:
1) Extend nft_exthdr to allow to match TCP options bitfields, from
Manuel Messner.
2) Allow to check if IPv6 extension header is present in nf_tables,
from Phil Sutter.
3) Allow to set and match conntrack zone in nf_tables, patches from
Florian Westphal.
4) Several patches for the nf_tables set infrastructure, this includes
cleanup and preparatory patches to add the new bitmap set type.
5) Add optional ruleset generation ID check to nf_tables and allow to
delete rules that got no public handle yet via NFTA_RULE_ID. These
patches add the missing kernel infrastructure to support rule
deletion by description from userspace.
6) Missing NFT_SET_OBJECT flag to select the right backend when sets
stores an object map.
7) A couple of cleanups for the expectation and SIP helper, from Gao
feng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This new attribute allows us to uniquely identify a rule in transaction.
Robots may trigger an insertion followed by deletion in a batch, in that
scenario we still don't have a public rule handle that we can use to
delete the rule. This is similar to the NFTA_SET_ID attribute that
allows us to refer to an anonymous set from a batch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After the dst->pending_confirm flag was removed, we do not
need anymore to provide dst arg to dst_neigh_output.
So, rename it to neigh_output as before commit 5110effee8
("net: Do delayed neigh confirmation.").
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sqkq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more updates:
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel. There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.
Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.
This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This command could be useful to inc/dec fields.
For example, to forward any TCP packet and decrease its TTL:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower ip_proto tcp \
action pedit munge ip ttl add 0xff pipe \
action mirred egress redirect dev veth0
In the example above, adding 0xff to this u8 field is actually
decreasing it by one, since the operation is masked.
Signed-off-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend pedit to enable the user setting offset relative to network
headers. This change would enable to work with more complex header
schemes (vs the simple IPv4 case) where setting a fixed offset relative
to the network header is not enough.
After this patch, the action has information about the exact header type
and field inside this header. This information could be used later on
for hardware offloading of pedit.
Backward compatibility was being kept:
1. Old kernel <-> new userspace
2. New kernel <-> old userspace
3. add rule using new userspace <-> dump using old userspace
4. add rule using old userspace <-> dump using new userspace
When using the extended api, new netlink attributes are being used. This
way, operation will fail in (1) and (3) - and no malformed rule be added
or dumped. Of course, new user space that doesn't need the new
functionality can use the old netlink attributes and operation will
succeed.
Since action can support both api's, (2) should work, and it is easy to
write the new user space to have (4) work.
The action is having a strict check that only header types and commands
it can handle are accepted. This way future additions will be much
easier.
Usage example:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
dst_port 80 \
action pedit munge tcp dport set 8080 pipe \
action mirred egress redirect dev veth0
Will forward tcp port whose original dest port is 80, while modifying
the destination port to 8080.
Signed-off-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload the mc router ports list, whenever it is being changed.
It is done because in some cases mc packets needs to be flooded to all
the ports in this list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload multicast disabled flag, for more accurate mc flood behavior:
When it is on, the mdb should be ignored.
When it is off, unregistered mc packets should be flooded to mc router
ports.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creation is done in this file, move destruction to be at the same place.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function destroys TC filter protocol, not TC filter. So name it
accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain currently uses the NLM_F_{REPLACE,APPEND}
flags to signal routes being replaced or appended.
Instead of using netlink flags for in-kernel notifications we can simply
introduce two new events in the FIB notification chain. This has the
added advantage of making the API cleaner, thereby making it clear that
these events should be supported by listeners of the notification chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Sender-Side Procedures for the Add
Outgoing and Incoming Streams Request Parameter described in
rfc6525 section 5.1.5-5.1.6.
It is also to add sockopt SCTP_ADD_STREAMS in rfc6525 section
6.3.4 for users.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define Add Incoming/Outgoing Streams Request
Parameter described in rfc6525 section 4.5 and 4.6. They can
be in one same chunk trunk as rfc6525 section 3.1-7 describes,
so make them in one function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Sender-Side Procedures for the SSN/TSN
Reset Request Parameter descibed in rfc6525 section 5.1.4.
It is also to add sockopt SCTP_RESET_ASSOC in rfc6525 section 6.3.3
for users.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define SSN/TSN Reset Request Parameter described
in rfc6525 section 4.3.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only needed it to register the policy backend at init time.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Just call xfrm_garbage_collect_deferred() directly.
This gets rid of a write to afinfo in register/unregister and allows to
constify afinfo later on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Nothing checks the return value. Also, the errors returned on unregister
are impossible (we only support INET and INET6, so no way
xfrm_policy_afinfo[afinfo->family] can be anything other than 'afinfo'
itself).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Nothing writes to these structures (the module owner was not used).
While at it, size xfrm_input_afinfo[] by the highest existing xfrm family
(INET6), not AF_MAX.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When a multipath route is hit the kernel doesn't consider nexthops that
are DEAD or LINKDOWN when IN_DEV_IGNORE_ROUTES_WITH_LINKDOWN is set.
Devices that offload multipath routes need to be made aware of nexthop
status changes. Otherwise, the device will keep forwarding packets to
non-functional nexthops.
Add the FIB_EVENT_NH_{ADD,DEL} events to the fib notification chain,
which notify capable devices when they should add or delete a nexthop
from their tables.
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error was reported upgrading to 4.9.8:
root@Typhoon:~# ip route add default table 210 nexthop dev eth0 via 10.68.64.1
weight 1 nexthop dev eth0 via 10.68.64.2 weight 1
RTNETLINK answers: Operation not supported
The problem occurs when CONFIG_LWTUNNEL is not enabled and a multipath
route is submitted.
The point of lwtunnel_valid_encap_type_attr is catch modules that
need to be loaded before any references are taken with rntl held. With
CONFIG_LWTUNNEL disabled, there will be no modules to load so the
lwtunnel_valid_encap_type_attr stub should just return 0.
Fixes: 9ed59592e3 ("lwtunnel: fix autoload of lwt modules")
Reported-by: pupilla@libero.it
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space notation allows us to classify the set backend implementation
based on the amount of required memory. This provides an order of the
set representation scalability in terms of memory. The size field is
still left in place so use this if the userspace provides no explicit
number of elements, so we cannot calculate the real memory that this set
needs. This also helps us break ties in the set backend selection
routine, eg. two backend implementations provide the same performance.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use lookup as field name instead, to prepare the introduction of the
memory class in a follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This provides context to walk callback iterator, thus, we know if the
walk happens from the set flush path. This is required by the new bitmap
set type coming in a follow up patch which has no real struct
nft_set_ext, so it has to allocate it based on the two bit compact
element representation.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Although semantics are similar to deactivate() with no implicit element
lookup, this is only called from the set flush path, so better rename
this to flush().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the benefit of drivers that rebuild IEs in firmware, parse the
IEs for HT/VHT capabilities and the respective membership selector
in the (extended) supported rates. This avoids duplicating the same
code into all drivers that need this information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
__packed is considered harmful as it potentially generates code that
doesn't perform well and its usage should be avoided as much as
possible.
This patch drops __packed from all SCTP structures except one, which is
sctp_signed_cookie. In there it's required, as per changelog on
commit 9834a2bb49 ("[SCTP]: Fix sctp_cookie alignment in the packet.").
After this patch, no alignment changes neither in x86 or x86_64 and
no exceptions were noticed during testing on both archs.
Code size for SCTP module also didn't change with this patch.
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As last step, we can remove the pending_confirm flag.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add confirm_neigh method to dst_ops and use it from IPv4 and IPv6
to lookup and confirm the neighbour. Its usage via the new helper
dst_confirm_neigh() should be restricted to MSG_PROBE users for
performance reasons.
For XFRM prefer the last tunnel address, if present. With help
from Steffen Klassert.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new transport flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The flag is propagated from transport to every packet.
It is reset when cached dst is reset.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new sock flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As not all call paths lock the socket use full word for
the flag.
Add sk_dst_confirm as replacement for dst_confirm when
called for received packets.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported that UDP sockets being destroyed would trigger the
WARN_ON(atomic_read(&sk->sk_rmem_alloc)); in inet_sock_destruct()
It turns out we do not properly destroy skb(s) that have wrong UDP
checksum.
Thanks again to syzkaller team.
Fixes : 7c13f97ffd ("udp: do fwd memory scheduling on dequeue")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for using this function in net/dsa/dsa2.c, rename the function
to make its scope DSA specific, and export it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A slave device will now notify the switch fabric once its port is
bridged or unbridged, instead of calling directly its switch operations.
This code allows propagating cross-chip bridging events in the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()
Fixes: 20e2a86485 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f26 ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Stash ctinfo 3-bit field into pointer to nf_conntrack object from
sk_buff so we only access one single cacheline in the conntrack
hotpath. Patchset from Florian Westphal.
2) Don't leak pointer to internal structures when exporting x_tables
ruleset back to userspace, from Willem DeBruijn. This includes new
helper functions to copy data to userspace such as xt_data_to_user()
as well as conversions of our ip_tables, ip6_tables and arp_tables
clients to use it. Not surprinsingly, ebtables requires an ad-hoc
update. There is also a new field in x_tables extensions to indicate
the amount of bytes that we copy to userspace.
3) Add nf_log_all_netns sysctl: This new knob allows you to enable
logging via nf_log infrastructure for all existing netnamespaces.
Given the effort to provide pernet syslog has been discontinued,
let's provide a way to restore logging using netfilter kernel logging
facilities in trusted environments. Patch from Michal Kubecek.
4) Validate SCTP checksum from conntrack helper, from Davide Caratti.
5) Merge UDPlite conntrack and NAT helpers into UDP, this was mostly
a copy&paste from the original helper, from Florian Westphal.
6) Reset netfilter state when duplicating packets, also from Florian.
7) Remove unnecessary check for broadcast in IPv6 in pkttype match and
nft_meta, from Liping Zhang.
8) Add missing code to deal with loopback packets from nft_meta when
used by the netdev family, also from Liping.
9) Several cleanups on nf_tables, one to remove unnecessary check from
the netlink control plane path to add table, set and stateful objects
and code consolidation when unregister chain hooks, from Gao Feng.
10) Fix harmless reference counter underflow in IPVS that, however,
results in problems with the introduction of the new refcount_t
type, from David Windsor.
11) Enable LIBCRC32C from nf_ct_sctp instead of nf_nat_sctp,
from Davide Caratti.
12) Missing documentation on nf_tables uapi header, from Liping Zhang.
13) Use rb_entry() helper in xt_connlimit, from Geliang Tang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver that offloads flower rules needs to know with which priority
user inserted the rules. So add this information into offload struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New ip_tunnel_info flag to represent bridged tunnel metadata.
Used by bridge driver later in the series to pass per vlan dst
metadata to bridge ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the encode/decode functionality from the ife module instead of using
implementation inside the act_ife.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This module is responsible for the ife encapsulation protocol
encode/decode logics. That module can:
- ife_encode: encode skb and reserve space for the ife meta header
- ife_decode: decode skb and extract the meta header size
- ife_tlv_meta_encode - encodes one tlv entry into the reserved ife
header space.
- ife_tlv_meta_decode - decodes one tlv entry from the packet
- ife_tlv_meta_next - advance to the next tlv
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the function ife_tlv_meta_encode is not used by any other module,
unexport it and make it static for the act_ife module.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69b34fb996 ("netfilter: xt_LOG: add net namespace support for
xt_LOG") disabled logging packets using the LOG target from non-init
namespaces. The motivation was to prevent containers from flooding
kernel log of the host. The plan was to keep it that way until syslog
namespace implementation allows containers to log in a safe way.
However, the work on syslog namespace seems to have hit a dead end
somewhere in 2013 and there are users who want to use xt_LOG in all
network namespaces. This patch allows to do so by setting
/proc/sys/net/netfilter/nf_log_all_netns
to a nonzero value. This sysctl is only accessible from init_net so that
one cannot switch the behaviour from inside a container.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, the ip_vs_dest cache frees ip_vs_dest objects when their
reference count becomes < 0. Aside from not being semantically sound,
this is problematic for the new type refcount_t, which will be introduced
shortly in a separate patch. refcount_t is the new kernel type for
holding reference counts, and provides overflow protection and a
constrained interface relative to atomic_t (the type currently being
used for kernel reference counts).
Per Julian Anastasov: "The problem is that dest_trash currently holds
deleted dests (unlinked from RCU lists) with refcnt=0." Changing
dest_trash to hold dest with refcnt=1 will allow us to free ip_vs_dest
structs when their refcnt=0, in ip_vs_dest_put_and_free().
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After this change conntrack operations (lookup, creation, matching from
ruleset) only access one instead of two sk_buff cache lines.
This works for normal conntracks because those are allocated from a slab
that guarantees hw cacheline or 8byte alignment (whatever is larger)
so the 3 bits needed for ctinfo won't overlap with nf_conn addresses.
Template allocation now does manual address alignment (see previous change)
on arches that don't have sufficent kmalloc min alignment.
Some spots intentionally use skb->_nfct instead of skb_nfct() helpers,
this is to avoid undoing the skb_nfct() use when we remove untracked
conntrack object in the future.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The next change will merge skb->nfct pointer and skb->nfctinfo
status bits into single skb->_nfct (unsigned long) area.
For this to work nf_conn addresses must always be aligned at least on
an 8 byte boundary since we will need the lower 3bits to store nfctinfo.
Conntrack templates are allocated via kmalloc.
kbuild test robot reported
BUILD_BUG_ON failed: NFCT_INFOMASK >= ARCH_KMALLOC_MINALIGN
on v1 of this patchset, so not all platforms meet this requirement.
Do manual alignment if needed, the alignment offset is stored in the
nf_conn entry protocol area. This works because templates are not
handed off to L4 protocol trackers.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a helper to assign a nf_conn entry and the ctinfo bits to an sk_buff.
This avoids changing code in followup patch that merges skb->nfct and
skb->nfctinfo into skb->_nfct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Followup patch renames skb->nfct and changes its type so add a helper to
avoid intrusive rename change later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Next patch makes direct skb->nfct access illegal, reduce noise
in next patch by using accessors we already have.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It is never accessed for reading and the only places that write to it
are the icmp(6) handlers, which also set skb->nfct (and skb->nfctinfo).
The conntrack core specifically checks for attached skb->nfct after
->error() invocation and returns early in this case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-02-01
1) Some typo fixes, from Alexander Alemayhu.
2) Don't acquire state lock in get_mtu functions.
The only rece against a dead state does not matter.
From Florian Westphal.
3) Remove xfrm4_state_fini, it is unused for more than
10 years. From Florian Westphal.
4) Various rcu usage improvements. From Florian Westphal.
5) Properly handle crypto arrors in ah4/ah6.
From Gilad Ben-Yossef.
6) Try to avoid skb linearization in esp4 and esp6.
7) The esp trailer is now set up in different places,
add a helper for this.
8) With the upcomming usage of gro_cells in IPsec,
a gro merged skb can have a secpath. Drop it
before freeing or reusing the skb.
9) Add a xfrm dummy network device for napi. With
this we can use gro_cells from within xfrm,
it allows IPsec GRO without impact on the generic
networking code.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_make_flowlabel() determines the flow label for IPv6 packets. It's
supposed to be passed a flow label, which it returns as is if non-0 and
in some other cases, otherwise it calculates a new value.
The problem is callers often pass a flowi6.flowlabel, which may also
contain traffic class bits. If the traffic class is non-0
ip6_make_flowlabel() mistakes the non-0 it gets as a flow label and
returns the whole thing. Thus it can return a 'flow label' longer than
20b and the low 20b of that is typically 0 resulting in packets with 0
label. Moreover, different packets of a flow may be labeled differently.
For a TCP flow with ECN non-payload and payload packets get different
labels as exemplified by this pair of consecutive packets:
(pure ACK)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT)
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0)
.... .... .... 0001 1100 1110 0100 1001 = Flow Label: 0x1ce49
Payload Length: 32
Next Header: TCP (6)
(payload)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0))
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2)
.... .... .... 0000 0000 0000 0000 0000 = Flow Label: 0x00000
Payload Length: 688
Next Header: TCP (6)
This patch allows ip6_make_flowlabel() to be passed more than just a
flow label and has it extract the part it really wants. This was simpler
than modifying the callers. With this patch packets like the above become
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT)
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0)
.... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e
Payload Length: 32
Next Header: TCP (6)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
0110 .... = Version: 6
.... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0))
.... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
.... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2)
.... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e
Payload Length: 688
Next Header: TCP (6)
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary plumbing at the slave network device level to have switch
drivers implement ndo_setup_tc() and most particularly the cls_matchall
classifier. We add support for two switch operations:
port_add_mirror and port_del_mirror() which configure, on a per-port
basis the mirror parameters requested from the cls_matchall classifier.
Code is largely borrowed from the Mellanox Spectrum switch driver.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing about lwt state requires a device reference, so remove the
input argument.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets arriving in a VRF currently are delivered to UDP sockets that
aren't bound to any interface. TCP defaults to not delivering packets
arriving in a VRF to unbound sockets. IP route lookup and socket
transmit both assume that unbound means using the default table and
UDP applications that haven't been changed to be aware of VRFs may not
function correctly in this case since they may not be able to handle
overlapping IP address ranges, or be able to send packets back to the
original sender if required.
So add a sysctl, udp_l3mdev_accept, to control this behaviour with it
being analgous to the existing tcp_l3mdev_accept, namely to allow a
process to have a VRF-global listen socket. Have this default to off
as this is the behaviour that users will expect, given that there is
no explicit mechanism to set unmodified VRF-unaware application into a
default VRF.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for CFP/TCAMP in the bcm_sf2 driver add the
plumbing to call into driver specific {get,set}_rxnfc operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bridge_dev pointer from dsa_slave_priv to dsa_port so that DSA
drivers can access this information and remove the need to cache it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.
That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slava Shwartsman reported a warning in skb_try_coalesce(), when we
detect skb->truesize is completely wrong.
In his case, issue came from IPv6 reassembly coping with malicious
datagrams, that forced various pskb_may_pull() to reallocate a bigger
skb->head than the one allocated by NIC driver before entering GRO
layer.
Current code does not change skb->truesize, leaving this burden to
callers if they care enough.
Blindly changing skb->truesize in pskb_expand_head() is not
easy, as some producers might track skb->truesize, for example
in xmit path for back pressure feedback (sk->sk_wmem_alloc)
We can detect the cases where it should be safe to change
skb->truesize :
1) skb is not attached to a socket.
2) If it is attached to a socket, destructor is sock_edemux()
My audit gave only two callers doing their own skb->truesize
manipulation.
I had to remove skb parameter in sock_edemux macro when
CONFIG_INET is not set to avoid a compile error.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5 ("tcp: fix mark propagation with fwmark_reflect enabled")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address generation mode for IPv6 link-local can only be configured
by netlink messages. This patch adds the ability to change the address
generation mode via sysctl.
v1 -> v2
Removed the rtnl lock and switch to use RCU lock to iterate through
the netdev list.
v2 -> v3
Removed the addrgenmode variable from the idev structure and use the
systcl storage for the flag.
Simplifed the logic for sysctl handling by removing the supported
for all operation.
Added support for more types of tunnel interfaces for link-local
address generation.
Based the patches from net-next.
v3 -> v4
Removed unnecessary whitespace changes.
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains a large batch with Netfilter fixes for
your net tree, they are:
1) Two patches to solve conntrack garbage collector cpu hogging, one to
remove GC_MAX_EVICTS and another to look at the ratio (scanned entries
vs. evicted entries) to make a decision on whether to reduce or not
the scanning interval. From Florian Westphal.
2) Two patches to fix incorrect set element counting if NLM_F_EXCL is
is not set. Moreover, don't decrenent set->nelems from abort patch
if -ENFILE which leaks a spare slot in the set. This includes a
patch to deconstify the set walk callback to update set->ndeact.
3) Two fixes for the fwmark_reflect sysctl feature: Propagate mark to
reply packets both from nf_reject and local stack, from Pau Espin Pedrol.
4) Fix incorrect handling of loopback traffic in rpfilter and nf_tables
fib expression, from Liping Zhang.
5) Fix oops on stateful objects netlink dump, when no filter is specified.
Also from Liping Zhang.
6) Fix a build error if proc is not available in ipt_CLUSTERIP, related
to fix that was applied in the previous batch for net. From Arnd Bergmann.
7) Fix lack of string validation in table, chain, set and stateful
object names in nf_tables, from Liping Zhang. Moreover, restrict
maximum log prefix length to 127 bytes, otherwise explicitly bail
out.
8) Two patches to fix spelling and typos in nf_tables uapi header file
and Kconfig, patches from Alexander Alemayhu and William Breathitt Gray.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patches have moved the temperature sensor code into the
Marvell PHYs. A few now dead references to NET_DSA_HWMON were left
behind. Go reap them.
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without TFO, any subsequent connect() call after a successful one returns
-1 EISCONN. The last API update ensured that __inet_stream_connect() can
return -1 EINPROGRESS in response to sendmsg() when TFO is in use to
indicate that the connection is now in progress. Unfortunately since this
function is used both for connect() and sendmsg(), it has the undesired
side effect of making connect() now return -1 EINPROGRESS as well after
a successful call, while at the same time poll() returns POLLOUT. This
can confuse some applications which happen to call connect() and to
check for -1 EISCONN to ensure the connection is usable, and for which
EINPROGRESS indicates a need to poll, causing a loop.
This problem was encountered in haproxy where a call to connect() is
precisely used in certain cases to confirm a connection's readiness.
While arguably haproxy's behaviour should be improved here, it seems
important to aim at a more robust behaviour when the goal of the new
API is to make it easier to implement TFO in existing applications.
This patch simply ensures that we preserve the same semantics as in
the non-TFO case on the connect() syscall when using TFO, while still
returning -1 EINPROGRESS on sendmsg(). For this we simply tell
__inet_stream_connect() whether we're doing a regular connect() or in
fact connecting for a sendmsg() call.
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new socket option, TCP_FASTOPEN_CONNECT, as an
alternative way to perform Fast Open on the active side (client). Prior
to this patch, a client needs to replace the connect() call with
sendto(MSG_FASTOPEN). This can be cumbersome for applications who want
to use Fast Open: these socket operations are often done in lower layer
libraries used by many other applications. Changing these libraries
and/or the socket call sequences are not trivial. A more convenient
approach is to perform Fast Open by simply enabling a socket option when
the socket is created w/o changing other socket calls sequence:
s = socket()
create a new socket
setsockopt(s, IPPROTO_TCP, TCP_FASTOPEN_CONNECT …);
newly introduced sockopt
If set, new functionality described below will be used.
Return ENOTSUPP if TFO is not supported or not enabled in the
kernel.
connect()
With cookie present, return 0 immediately.
With no cookie, initiate 3WHS with TFO cookie-request option and
return -1 with errno = EINPROGRESS.
write()/sendmsg()
With cookie present, send out SYN with data and return the number of
bytes buffered.
With no cookie, and 3WHS not yet completed, return -1 with errno =
EINPROGRESS.
No MSG_FASTOPEN flag is needed.
read()
Return -1 with errno = EWOULDBLOCK/EAGAIN if connect() is called but
write() is not called yet.
Return -1 with errno = EWOULDBLOCK/EAGAIN if connection is
established but no msg is received yet.
Return number of bytes read if socket is established and there is
msg received.
The new API simplifies life for applications that always perform a write()
immediately after a successful connect(). Such applications can now take
advantage of Fast Open by merely making one new setsockopt() call at the time
of creating the socket. Nothing else about the application's socket call
sequence needs to change.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the cookie check logic in tcp_send_syn_data() into a function.
This function will be called else where in later changes.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce optional 128-bit action cookie.
Like all other cookie schemes in the networking world (eg in protocols
like http or existing kernel fib protocol field, etc) the idea is to save
user state that when retrieved serves as a correlator. The kernel
_should not_ intepret it. The user can store whatever they wish in the
128 bits.
Sample exercise(showing variable length use of cookie)
.. create an accept action with cookie a1b2c3d4
sudo $TC actions add action ok index 1 cookie a1b2c3d4
.. dump all gact actions..
sudo $TC -s actions ls action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 1 bind 0 installed 5 sec used 5 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
cookie a1b2c3d4
.. bind the accept action to a filter..
sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 1
... send some traffic..
$ ping 127.0.0.1 -c 3
PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data.
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.020 ms
64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.027 ms
64 bytes from 127.0.0.1: icmp_seq=3 ttl=64 time=0.038 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
The header file has grown a lot of #define's etc, but
they are nicer as enums, so rewrite the file from the
documentation as such.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modules implementing lwtunnel ops should not be allowed to unload
while there is state alive using those ops, so specify the owning
module for all lwtunnel ops.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action allows the user to sample traffic matched by tc classifier.
The sampling consists of choosing packets randomly and sampling them using
the psample module. The user can configure the psample group number, the
sampling rate and the packet's truncation (to save kernel-user traffic).
Example:
To sample ingress traffic from interface eth1, one may use the commands:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff: \
matchall action sample rate 12 group 4
Where the first command adds an ingress qdisc and the second starts
sampling randomly with an average of one sampled packet per 12 packets on
dev eth1 to psample group 4.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a general way for kernel modules to sample packets, without being tied
to any specific subsystem. This netlink channel can be used by tc,
iptables, etc. and allow to standardize packet sampling in the kernel.
For every sampled packet, the psample module adds the following metadata
fields:
PSAMPLE_ATTR_IIFINDEX - the packets input ifindex, if applicable
PSAMPLE_ATTR_OIFINDEX - the packet output ifindex, if applicable
PSAMPLE_ATTR_ORIGSIZE - the packet's original size, in case it has been
truncated during sampling
PSAMPLE_ATTR_SAMPLE_GROUP - the packet's sample group, which is set by the
user who initiated the sampling. This field allows the user to
differentiate between several samplers working simultaneously and
filter packets relevant to him
PSAMPLE_ATTR_GROUP_SEQ - sequence counter of last sent packet. The
sequence is kept for each group
PSAMPLE_ATTR_SAMPLE_RATE - the sampling rate used for sampling the packets
PSAMPLE_ATTR_DATA - the actual packet bits
The sampled packets are sent to the PSAMPLE_NL_MCGRP_SAMPLE multicast
group. In addition, add the GET_GROUPS netlink command which allows the
user to see the current sample groups, their refcount and sequence number.
This command currently supports only netlink dump mode.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add net.ipv4.ip_unprivileged_port_start, which is a per namespace sysctl
that denotes the first unprivileged inet port in the namespace. To
disable all privileged ports set this to zero. It also checks for
overlap with the local port range. The privileged and local range may
not overlap.
The use case for this change is to allow containerized processes to bind
to priviliged ports, but prevent them from ever being allowed to modify
their container's network configuration. The latter is accomplished by
ensuring that the network namespace is not a child of the user
namespace. This modification was needed to allow the container manager
to disable a namespace's priviliged port restrictions without exposing
control of the network namespace to processes in the user namespace.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a few restructured text warnings in mac80211, making the
documentation warning-free (for now).
In order to not add trailing whitespace, but also not introduce
too much noise into this change, move just the affected docs
into inline comments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new restructured text parser complains about the formatting,
and really this should be a definition list.
In order to fix this without introducing trailing whitespace,
convert to the inline kernel-doc format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cast second parameter of csum_sub() from __sum16 to __wsum.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hlist_entry_safe() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohua Li made percpu_counter irq safe in commit 098faf5805
("percpu_counter: make APIs irq safe")
We can safely remove BH disable/enable sections around various
percpu_counter manipulations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to add an mpls encap route when the MPLS modules are not loaded
hangs. For example:
CONFIG_MPLS=y
CONFIG_NET_MPLS_GSO=m
CONFIG_MPLS_ROUTING=m
CONFIG_MPLS_IPTUNNEL=m
$ ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
The ip command hangs:
root 880 826 0 21:25 pts/0 00:00:00 ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
$ cat /proc/880/stack
[<ffffffff81065a9b>] call_usermodehelper_exec+0xd6/0x134
[<ffffffff81065efc>] __request_module+0x27b/0x30a
[<ffffffff814542f6>] lwtunnel_build_state+0xe4/0x178
[<ffffffff814aa1e4>] fib_create_info+0x47f/0xdd4
[<ffffffff814ae451>] fib_table_insert+0x90/0x41f
[<ffffffff814a8010>] inet_rtm_newroute+0x4b/0x52
...
modprobe is trying to load rtnl-lwt-MPLS:
root 881 5 0 21:25 ? 00:00:00 /sbin/modprobe -q -- rtnl-lwt-MPLS
and it hangs after loading mpls_router:
$ cat /proc/881/stack
[<ffffffff81441537>] rtnl_lock+0x12/0x14
[<ffffffff8142ca2a>] register_netdevice_notifier+0x16/0x179
[<ffffffffa0033025>] mpls_init+0x25/0x1000 [mpls_router]
[<ffffffff81000471>] do_one_initcall+0x8e/0x13f
[<ffffffff81119961>] do_init_module+0x5a/0x1e5
[<ffffffff810bd070>] load_module+0x13bd/0x17d6
...
The problem is that lwtunnel_build_state is called with rtnl lock
held preventing mpls_init from registering.
Given the potential references held by the time lwtunnel_build_state it
can not drop the rtnl lock to the load module. So, extract the module
loading code from lwtunnel_build_state into a new function to validate
the encap type. The new function is called while converting the user
request into a fib_config which is well before any table, device or
fib entries are examined.
Fixes: 745041e2aa ("lwtunnel: autoload of lwt modules")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525 section
5.1.2 and 5.1.3.
It is also add sockopt SCTP_RESET_STREAMS in rfc6525 section 6.3.2
for users.
Note that the new asoc member strreset_outstanding is to make sure
only one reconf request chunk on the fly as rfc6525 section 5.1.1
demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add sockopt SCTP_ENABLE_STREAM_RESET to get/set
strreset_enable to indicate which reconf request type it supports,
which is described in rfc6525 section 6.3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add reconf_enable field in all of asoc ep and netns
to indicate if they support stream reset.
When initializing, asoc reconf_enable get the default value from ep
reconf_enable which is from netns netns reconf_enable by default.
It is also to add reconf_capable in asoc peer part to know if peer
supports reconf_enable, the value is set if ext params have reconf
chunk support when processing init chunk, just as rfc6525 section
5.1.1 demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a primitive based on sctp primitive frame for
sending stream reconf request. It works as the other primitives,
and create a SCTP_CMD_REPLY command to send the request chunk out.
sctp_primitive_RECONF would be the api to send a reconf request
chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a per transport timer based on sctp timer frame
for stream reconf chunk retransmission. It would start after sending
a reconf request chunk, and stop after receiving the response chunk.
If the timer expires, besides retransmitting the reconf request chunk,
it would also do the same thing with data RTO timer. like to increase
the appropriate error counts, and perform threshold management, possibly
destroying the asoc if sctp retransmission thresholds are exceeded, just
as section 5.1.1 describes.
This patch is also to add asoc strreset_chunk, it is used to save the
reconf request chunk, so that it can be retransmitted, and to check if
the response is really for this request by comparing the information
inside with the response chunk as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add asoc strreset_outseq and strreset_inseq for
saving the reconf request sequence, initialize them when create
assoc and process init, and also to define Incoming and Outgoing
SSN Reset Request Parameter described in rfc6525 section 4.1 and
4.2, As they can be in one same chunk as section rfc6525 3.1-3
describes, it makes them in one function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have non reuseport sockets on a tb we will set tb->fastreuseport to 0 and
never set it again. Which means that in the future if we end up adding a bunch
of reuseport sk's to that tb we'll have to do the expensive scan every time.
Instead add the ipv4/ipv6 saddr fields to the bind bucket, as well as the family
so we know what comparison to make, and the ipv6 only setting so we can make
sure to compare with new sockets appropriately. Once one sk has made it onto
the list we know that there are no potential bind conflicts on the owners list
that match that sk's rcv_addr. So copy the sk's information into our bind
bucket and set tb->fastruseport to FASTREUSESOCK_STRICT so we know we have to do
an extra check for subsequent reuseport sockets and skip the expensive bind
conflict check.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In inet_csk_get_port we seem to be using smallest_port to figure out where the
best place to look for a SO_REUSEPORT sk that matches with an existing set of
SO_REUSEPORT's. However if we get to the logic
if (smallest_size != -1) {
port = smallest_port;
goto have_port;
}
we will do a useless search, because we would have already done the
inet_csk_bind_conflict for that port and it would have returned 1, otherwise we
would have gone to found_tb and succeeded. Since this logic makes us do yet
another trip through inet_csk_bind_conflict for a port we know won't work just
delete this code and save us the time.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function. I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the functionality for including address-family-specific per-link
stats in RTM_GETSTATS messages. This is done through adding a new
IFLA_STATS_AF_SPEC attribute under which address family attributes are
nested and then the AF-specific attributes can be further nested. This
follows the model of IFLA_AF_SPEC on RTM_*LINK messages and it has the
advantage of presenting an easily extended hierarchy. The rtnl_af_ops
structure is extended to provide AFs with the opportunity to fill and
provide the size of their stats attributes.
One alternative would have been to provide AFs with the ability to add
attributes directly into the RTM_GETSTATS message without a nested
hierarchy. I discounted this approach as it increases the rate at
which the 32 attribute number space is used up and it makes
implementation a little more tricky for stats dump resuming (at the
moment the order in which attributes are added to the message has to
match the numeric order of the attributes).
Another alternative would have been to register per-AF RTM_GETSTATS
handlers. I discounted this approach as I perceived a common use-case
to be getting all the stats for an interface and this approach would
necessitate multiple requests/dumps to retrieve them all.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to avoid skb_cow_data on esp4.
On the encrypt side we add the IPsec tailbits
to the linear part of the buffer if there is
space on it. If there is no space on the linear
part, we add a page fragment with the tailbits to
the buffer and use separate src and dst scatterlists.
On the decrypt side, we leave the buffer as it is
if it is not cloned.
With this, we can avoid a linearization of the buffer
in most of the cases.
Joint work with:
Sowmini Varadhan <sowmini.varadhan@oracle.com>
Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently, we check the existing rtable in PREROUTING hook, if RTCF_LOCAL
is set, we assume that the packet is loopback.
But this assumption is incorrect, for example, a packet encapsulated
in ipsec transport mode was received and routed to local, after
decapsulation, it would be delivered to local again, and the rtable
was not dropped, so RTCF_LOCAL check would trigger. But actually, the
packet was not loopback.
So for these normal loopback packets, we can check whether the in device
is IFF_LOOPBACK or not. For these locally generated broadcast/multicast,
we can check whether the skb->pkt_type is PACKET_LOOPBACK or not.
Finally, there's a subtle difference between nft fib expr and xtables
rpfilter extension, user can add the following nft rule to do strict
rpfilter check:
# nft add rule x y meta iif eth0 fib saddr . iif oif != eth0 drop
So when the packet is loopback, it's better to store the in device
instead of the LOOPBACK_IFINDEX, otherwise, after adding the above
nft rule, locally generated broad/multicast packets will be dropped
incorrectly.
Fixes: f83a7ea207 ("netfilter: xt_rpfilter: skip locally generated broadcast/multicast, too")
Fixes: f6d0cbcf09 ("netfilter: nf_tables: add fib expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch removes the support of RFC5827 early retransmit (i.e.,
fast recovery on small inflight with <3 dupacks) because it is
subsumed by the new RACK loss detection. More specifically when
RACK receives DUPACKs, it'll arm a reordering timer to start fast
recovery after a quarter of (min)RTT, hence it covers the early
retransmit except RACK does not limit itself to specific inflight
or dupack numbers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes two things:
1. Start fast recovery with RACK in addition to other heuristics
(e.g., DUPACK threshold, FACK). Prior to this change RACK
is enabled to detect losses only after the recovery has
started by other algorithms.
2. Disable TCP early retransmit. RACK subsumes the early retransmit
with the new reordering timer feature. A latter patch in this
series removes the early retransmit code.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packets inside a jumbo skb (e.g., TSO) share the same skb
timestamp, even though they are sent sequentially on the wire. Since
RACK is based on time, it can not detect some packets inside the
same skb are lost. However, we can leverage the packet sequence
numbers as extended timestamps to detect losses. Therefore, when
RACK timestamp is identical to skb's timestamp (i.e., one of the
packets of the skb is acked or sacked), we use the sequence numbers
of the acked and unacked packets to break ties.
We can use the same sequence logic to advance RACK xmit time as
well to detect more losses and avoid timeout.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes RACK install a reordering timer when it suspects
some packets might be lost, but wants to delay the decision
a little bit to accomodate reordering.
It does not create a new timer but instead repurposes the existing
RTO timer, because both are meant to retransmit packets.
Specifically it arms a timer ICSK_TIME_REO_TIMEOUT when
the RACK timing check fails. The wait time is set to
RACK.RTT + RACK.reo_wnd - (NOW - Packet.xmit_time) + fudge
This translates to expecting a packet (Packet) should take
(RACK.RTT + RACK.reo_wnd + fudge) to deliver after it was sent.
When there are multiple packets that need a timer, we use one timer
with the maximum timeout. Therefore the timer conservatively uses
the maximum window to expire N packets by one timeout, instead of
N timeouts to expire N packets sent at different times.
The fudge factor is 2 jiffies to ensure when the timer fires, all
the suspected packets would exceed the deadline and be marked lost
by tcp_rack_detect_loss(). It has to be at least 1 jiffy because the
clock may tick between calling icsk_reset_xmit_timer(timeout) and
actually hang the timer. The next jiffy is to lower-bound the timeout
to 2 jiffies when reo_wnd is < 1ms.
When the reordering timer fires (tcp_rack_reo_timeout): If we aren't
in Recovery we'll enter fast recovery and force fast retransmit.
This is very similar to the early retransmit (RFC5827) except RACK
is not constrained to only enter recovery for small outstanding
flights.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the most recent RTT in RACK. It is often identical to the
"ca_rtt_us" values in tcp_clean_rtx_queue. But when the packet has
been retransmitted, RACK choses to believe the ACK is for the
(latest) retransmitted packet if the RTT is over minimum RTT.
This requires passing the arrival time of the most recent ACK to
RACK routines. The timestamp is now recorded in the "ack_time"
in tcp_sacktag_state during the ACK processing.
This patch does not change the RACK algorithm itself. It only adds
the RTT variable to prepare the next main patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new helper tcp_rack_detect_loss to prepare the upcoming
RACK reordering timer patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function documentation for cfg80211_connect_bss() and
cfg80211_connect_result() was still claiming that they are used only for
a success case while these functions can now be used to report both
success and various failure cases. The actual use cases were already
described in the connect() documentation.
Update the function specific comments to note the failure cases and also
describe how the special status == -1 case is used in
cfg80211_connect_bss() to indicate a connection timeout based on the
internal implementation in cfg80211_connect_timeout().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[use tabs for indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enhances the connect timeout API to also carry the reason for the
timeout. These reason codes for the connect time out are represented by
enum nl80211_timeout_reason and are passed to user space through a new
attribute NL80211_ATTR_TIMEOUT_REASON (u32).
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[keep gfp_t argument last]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance sched scan to support option of finding a better BSS while in
connected state. Firmware scans the medium and reports when it finds a
known BSS which has better RSSI than the current connected BSS. New
attributes to specify the relative RSSI (compared to the current BSS)
are added to the sched scan to implement this.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With 78, 111 and 85 bytes respectively (on x86-64), the
functions iwe_stream_add_event(), iwe_stream_add_point()
and iwe_stream_add_value() really shouldn't be inlines.
It appears that at least my compiler already decided
the same, and created a single instance of each one
of them for each file using it, but that's still a
number of instances in the system overall, which this
reduces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flag that indicates that the WEP ICV was stripped from an
RX packet, allowing the device to not transfer that if it's
already checked.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
gcc-7 complains that wl3501_cs passes NULL into a function that
then uses the argument as the input for memcpy:
drivers/net/wireless/wl3501_cs.c: In function 'wl3501_get_scan':
include/net/iw_handler.h:559:3: error: argument 2 null where non-null expected [-Werror=nonnull]
memcpy(stream + point_len, extra, iwe->u.data.length);
This works fine here because iwe->u.data.length is guaranteed to be 0
and the memcpy doesn't actually have an effect.
Making the length check explicit avoids the warning and should have
no other effect here.
Also check the pointer itself, since otherwise we get warnings
elsewhere in the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow dissection of (R)ARP operation hardware and protocol addresses
for Ethernet hardware and IPv4 protocol addresses.
There are currently no users of FLOW_DISSECTOR_KEY_ARP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ARP to be used by the
flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_init_tempstate is always called from within rcu read side section.
We can thus use a simpler function that doesn't call rcu_read_lock
again.
While at it, also make xfrm_init_tempstate return value void, the
return value was never tested.
A followup patch will replace remaining callers of xfrm_state_get_afinfo
with xfrm_state_afinfo_get_rcu variant and then remove the 'old'
get_afinfo interface.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Support for SMC socket monitoring via netlink sockets of protocol
NETLINK_SOCK_DIAG.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direct call of tcp_set_keepalive() function from protocol-agnostic
sock_setsockopt() function in net/core/sock.c violates network
layering. And newly introduced protocol (SMC-R) will need its own
keepalive function. Therefore, add "keepalive" function pointer
to "struct proto", and call it from sock_setsockopt() via this pointer.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disconnect or deauthenticate when the owning socket is closed if this
flag is supplied to CMD_CONNECT or CMD_ASSOCIATE. This may be used
to ensure userspace daemon doesn't leave an unmanaged connection behind.
In some situations it would be possible to account for that, to some
degree, in the deamon restart code or in the up/down scripts without
the use of this attribute. But there will be systems where the daemon
can go away for varying periods without a warning due to local resource
management.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The tc_from field fulfills two roles. It encodes whether a packet was
redirected by an act_mirred device and, if so, whether act_mirred was
called on ingress or egress. Split it into separate fields.
The information is needed by the special IFB loop, where packets are
taken out of the normal path by act_mirred, forwarded to IFB, then
reinjected at their original location (ingress or egress) by IFB.
The IFB device cannot use skb->tc_at_ingress, because that may have
been overwritten as the packet travels from act_mirred to ifb_xmit,
when it passes through tc_classify on the IFB egress path. Cache this
value in skb->tc_from_ingress.
That field is valid only if a packet arriving at ifb_xmit came from
act_mirred. Other packets can be crafted to reach ifb_xmit. These
must be dropped. Set tc_redirected on redirection and drop all packets
that do not have this bit set.
Both fields are set only on cloned skbs in tc actions, so original
packet sources do not have to clear the bit when reusing packets
(notably, pktgen and octeon).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Field tc_at is used only within tc actions to distinguish ingress from
egress processing. A single bit is sufficient for this purpose.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the remaining two fields from tc_verd and remove the __u16
completely. TC_AT and TC_FROM are converted to equivalent two-bit
integer fields tc_at and tc_from. Where possible, use existing
helper skb_at_tc_ingress when reading tc_at. Introduce helper
skb_reset_tc to clear fields.
Not documenting tc_from and tc_at, because they will be replaced
with single bit fields in follow-on patches.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets sent by the IFB device skip subsequent tc classification.
A single bit governs this state. Move it out of tc_verd in
anticipation of removing that __u16 completely.
The new bitfield tc_skip_classify temporarily uses one bit of a
hole, until tc_verd is removed completely in a follow-up patch.
Remove the bit hole comment. It could be 2, 3, 4 or 5 bits long.
With that many options, little value in documenting it.
Introduce a helper function to deduplicate the logic in the two
sites that check this bit.
The field tc_skip_classify is set only in IFB on skbs cloned in
act_mirred, so original packet sources do not have to clear the
bit when reusing packets (notably, pktgen and octeon).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp stream reconf, described in RFC 6525, needs a structure to
save per stream information in assoc, like stream state.
In the future, sctp stream scheduler also needs it to save some
stream scheduler params and queues.
This patchset is to prepare the stream array in assoc for stream
reconf. It defines sctp_stream that includes stream arrays inside
to replace ssnmap.
Note that we use different structures for IN and OUT streams, as
the members in per OUT stream will get more and more different
from per IN stream.
v1->v2:
- put these patches into a smaller group.
v2->v3:
- define sctp_stream to contain stream arrays, and create stream.c
to put stream-related functions.
- merge 3 patches into 1, as new sctp_stream has the same name
with before.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default has a single caller within the same file.
Make it static.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a helper for reading that new property and applying
limitations of supported channels specified this way.
It is used with devices that normally support a wide wireless band but
in a given config are limited to some part of it (usually due to board
design). For example a dual-band chipset may be able to support one band
only because of used antennas.
It's also common that tri-band routers have separated radios for lower
and higher part of 5 GHz band and it may be impossible to say which is
which without a DT info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[add new function to documentation, fix link]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
udplite was copied from udp, they are virtually 100% identical.
This adds udplite tracker to udp instead, removes udplite module,
and then makes the udplite tracker builtin.
udplite will then simply re-use udp timeout settings.
It makes little sense to add separate sysctls, nowadays we have
fine-grained timeout policy support via the CT target.
old:
text data bss dec hex filename
1633 672 0 2305 901 nf_conntrack_proto_udp.o
1756 672 0 2428 97c nf_conntrack_proto_udplite.o
69526 17937 268 87731 156b3 nf_conntrack.ko
new:
text data bss dec hex filename
2442 1184 0 3626 e2a nf_conntrack_proto_udp.o
68565 17721 268 86554 1521a nf_conntrack.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Different namespace application might require different maximal
number of remembered connection requests.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require fast recycling
TIME-WAIT sockets independently of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to use this cascading. It doesn't add anything.
Let's remove it and simplify.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
Commit 4f7df337fe
"netlink: 2-clause nla_ok()" is BROKEN.
First clause tests if "->nla_len" could even be accessed at all,
it can not possibly be omitted.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
-----BEGIN PGP SIGNATURE-----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=HvKt
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sk_drops can be an often written field, do not read it unless
application showed interest.
Note that sk_drops can be read via inet_diag, so applications
can avoid getting this info from every received packet.
In the future, 'reading' sk_drops might require folding per node or per
cpu fields, and thus become even more expensive than today.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFS is not commonly used, so add a jump label to avoid some conditionals
in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow dissection of ICMP(V6) type and code. This should only occur
if a packet is ICMP(V6) and the dissector has FLOW_DISSECTOR_KEY_ICMP set.
There are currently no users of FLOW_DISSECTOR_KEY_ICMP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ICMP to be used by
the flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a large Netfilter update for net-next,
to summarise:
1) Add support for stateful objects. This series provides a nf_tables
native alternative to the extended accounting infrastructure for
nf_tables. Two initial stateful objects are supported: counters and
quotas. Objects are identified by a user-defined name, you can fetch
and reset them anytime. You can also use a maps to allow fast lookups
using any arbitrary key combination. More info at:
http://marc.info/?l=netfilter-devel&m=148029128323837&w=2
2) On-demand registration of nf_conntrack and defrag hooks per netns.
Register nf_conntrack hooks if we have a stateful ruleset, ie.
state-based filtering or NAT. The new nf_conntrack_default_on sysctl
enables this from newly created netnamespaces. Default behaviour is not
modified. Patches from Florian Westphal.
3) Allocate 4k chunks and then use these for x_tables counter allocation
requests, this improves ruleset load time and also datapath ruleset
evaluation, patches from Florian Westphal.
4) Add support for ebpf to the existing x_tables bpf extension.
From Willem de Bruijn.
5) Update layer 4 checksum if any of the pseudoheader fields is updated.
This provides a limited form of 1:1 stateless NAT that make sense in
specific scenario, eg. load balancing.
6) Add support to flush sets in nf_tables. This series comes with a new
set->ops->deactivate_one() indirection given that we have to walk
over the list of set elements, then deactivate them one by one.
The existing set->ops->deactivate() performs an element lookup that
we don't need.
7) Two patches to avoid cloning packets, thus speed up packet forwarding
via nft_fwd from ingress. From Florian Westphal.
8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
prevent infinite loops, patch from Dwip Banerjee. And one minor
refactoring from Gao feng.
9) Revisit recent log support for nf_tables netdev families: One patch
to ensure that we correctly handle non-ethernet packets. Another
patch to add missing logger definition for netdev. Patches from
Liping Zhang.
10) Three patches for nft_fib, one to address insufficient register
initialization and another to solve incorrect (although harmless)
byteswap operation. Moreover update xt_rpfilter and nft_fib to match
lbcast packets with zeronet as source, eg. DHCP Discover packets
(0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.
11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
been broken in many-cast mode for some little time, let's give them a
chance by placing them at the same level as other existing protocols.
Thus, users don't explicitly have to modprobe support for this and
NAT rules work for them. Some people point to the lack of support in
SOHO Linux-based routers that make deployment of new protocols harder.
I guess other middleboxes outthere on the Internet are also to blame.
Anyway, let's see if this has any impact in the midrun.
12) Skip software SCTP software checksum calculation if the NIC comes
with SCTP checksum offload support. From Davide Caratti.
13) Initial core factoring to prepare conversion to hook array. Three
patches from Aaron Conole.
14) Gao Feng made a wrong conversion to switch in the xt_multiport
extension in a patch coming in the previous batch. Fix it in this
batch.
15) Get vmalloc call in sync with kmalloc flags to avoid a warning
and likely OOM killer intervention from x_tables. From Marcelo
Ricardo Leitner.
16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo noticed a cache line miss in UDP recvmsg() to access
sk_rxhash, sharing a cache line with sk_drops.
sk_drops might be heavily incremented by cpus handling a flood targeting
this socket.
We might place sk_drops on a separate cache line, but lets try
to avoid wasting 64 bytes per socket just for this, since we have
other bottlenecks to take care of.
sock_rps_record_flow() should only access sk_rxhash for connected
flows.
Testing sk_state for TCP_ESTABLISHED covers most of the cases for
connected sockets, for a zero cost, since system calls using
sock_rps_record_flow() also access sk->sk_prot which is on the
same cache line.
A follow up patch will provide a static_key (Jump Label) since most
hosts do not even use RFS.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for set flushing, that consists of walking over
the set elements if the NFTA_SET_ELEM_LIST_ELEMENTS attribute is set.
This patch requires the following changes:
1) Add set->ops->deactivate_one() operation: This allows us to
deactivate an element from the set element walk path, given we can
skip the lookup that happens in ->deactivate().
2) Add a new nft_trans_alloc_gfp() function since we need to allocate
transactions using GFP_ATOMIC given the set walk path happens with
held rcu_read_lock.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows you to refer to stateful objects from set elements.
This provides the infrastructure to create maps where the right hand
side of the mapping is a stateful object.
This allows us to build dictionaries of stateful objects, that you can
use to perform fast lookups using any arbitrary key combination.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Notify on depleted quota objects. The NFT_QUOTA_F_DEPLETED flag
indicates we have reached overquota.
Add pointer to table from nft_object, so we can use it when sending the
depletion notification to userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce nf_tables_obj_notify() to notify internal state changes in
stateful objects. This is used by the quota object to report depletion
in a follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new NFT_MSG_GETOBJ_RESET command perform an atomic
dump-and-reset of the stateful object. This also comes with add support
for atomic dump and reset for counter and quota objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch augments nf_tables to support stateful objects. This new
infrastructure allows you to create, dump and delete stateful objects,
that are identified by a user-defined name.
This patch adds the generic infrastructure, follow up patches add
support for two stateful objects: counters and quotas.
This patch provides a native infrastructure for nf_tables to replace
nfacct, the extended accounting infrastructure for iptables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
... so we can use current skb instead of working with a clone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new flag that signals the kernel to update layer 4
checksum if the packet field belongs to the layer 4 pseudoheader. This
implicitly provides stateless NAT 1:1 that is useful under very specific
usecases.
Since rules mangling layer 3 fields that are part of the pseudoheader
may potentially convey any layer 4 packet, we have to deal with the
layer 4 checksum adjustment using protocol specific code.
This patch adds support for TCP, UDP and ICMPv6, since they include the
pseudoheader in the layer 4 checksum calculation. ICMP doesn't, so we
can skip it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_defrag modules for ipv4 and ipv6 export an empty stub function.
Any module that needs the defragmentation hooks registered simply 'calls'
this empty function to create a phony module dependency -- modprobe will
then load the defrag module too.
This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook
registration until the functionality is requested within a network namespace
instead of module load time for all namespaces.
Hooks are only un-registered on module unload or when a namespace that used
such defrag functionality exits.
We have to use struct net for this as the register hooks can be called
before netns initialization here from the ipv4/ipv6 conntrack module
init path.
There is no unregister functionality support, defrag will always be
active once it was requested inside a net namespace.
The reason is that defrag has impact on nft and iptables rulesets
(without defrag we might see framents).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Old code was hard to maintain, due to complex lock chains.
(We probably will be able to remove some kfree_rcu() in callers)
2) Using a single timer to update all estimators does not scale.
3) Code was buggy on 32bit kernel (WRITE_ONCE() on 64bit quantity
is not supposed to work well)
In this rewrite :
- I removed the RB tree that had to be scanned in
gen_estimator_active(). qdisc dumps should be much faster.
- Each estimator has its own timer.
- Estimations are maintained in net_rate_estimator structure,
instead of dirtying the qdisc. Minor, but part of the simplification.
- Reading the estimator uses RCU and a seqcount to provide proper
support for 32bit kernels.
- We reduce memory need when estimators are not used, since
we store a pointer, instead of the bytes/packets counters.
- xt_rateest_mt() no longer has to grab a spinlock.
(In the future, xt_rateest_tg() could be switched to per cpu counters)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Group fields used in TX path, and keep some cache lines mostly read
to permit sharing among cpus.
Gained two 4 bytes holes on 64bit arches.
Added a place holder for tcp tsq_flags, next to sk_wmem_alloc
to speed up tcp_wfree() in the following patch.
I have not added ____cacheline_aligned_in_smp, this might be done later.
I prefer doing this once inet and tcp/udp sockets reorg is also done.
Tested with both TCP and UDP.
UDP receiver performance under flood increased by ~20 % :
Accessing sk_filter/sk_wq/sk_napi_id no longer stalls because sk_drops
was moved away from a critical cache line, now mostly read and shared.
/* --- cacheline 4 boundary (256 bytes) --- */
unsigned int sk_napi_id; /* 0x100 0x4 */
int sk_rcvbuf; /* 0x104 0x4 */
struct sk_filter * sk_filter; /* 0x108 0x8 */
union {
struct socket_wq * sk_wq; /* 0x8 */
struct socket_wq * sk_wq_raw; /* 0x8 */
}; /* 0x110 0x8 */
struct xfrm_policy * sk_policy[2]; /* 0x118 0x10 */
struct dst_entry * sk_rx_dst; /* 0x128 0x8 */
struct dst_entry * sk_dst_cache; /* 0x130 0x8 */
atomic_t sk_omem_alloc; /* 0x138 0x4 */
int sk_sndbuf; /* 0x13c 0x4 */
/* --- cacheline 5 boundary (320 bytes) --- */
int sk_wmem_queued; /* 0x140 0x4 */
atomic_t sk_wmem_alloc; /* 0x144 0x4 */
long unsigned int sk_tsq_flags; /* 0x148 0x8 */
struct sk_buff * sk_send_head; /* 0x150 0x8 */
struct sk_buff_head sk_write_queue; /* 0x158 0x18 */
__s32 sk_peek_off; /* 0x170 0x4 */
int sk_write_pending; /* 0x174 0x4 */
long int sk_sndtimeo; /* 0x178 0x8 */
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch (default on) can be used to disable automatic registration
of connection tracking functionality in newly created network
namespaces.
This means that when net namespace goes down (or the tracker protocol
module is unloaded) we *might* have to unregister the hooks.
We can either add another per-netns variable that tells if
the hooks got registered by default, or, alternatively, just call
the protocol _put() function and have the callee deal with a possible
'extra' put() operation that doesn't pair with a get() one.
This uses the latter approach, i.e. a put() without a get has no effect.
Conntrack is still enabled automatically regardless of the new sysctl
setting if the new net namespace requires connection tracking, e.g. when
NAT rules are created.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since adf0516845 ("netfilter: remove ip_conntrack* sysctl compat code")
the only user (ipv4 tracker) sets this to an empty stub function.
After this change nf_ct_l3proto_pernet_register() is also empty,
but this will change in a followup patch to add conditional register
of the hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection
tracking support for DCCP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| dccp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 469140 | 828755 | 828676 | 6141434
DCCP || - | 830566 | 829935 | 6533526
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In netdev family, we will handle non ethernet packets, so using
eth_hdr(skb)->h_proto is incorrect.
Meanwhile, we can use socket(AF_PACKET...) to sending packets, so
skb->protocol is not always set in bridge family.
Add an extra parameter into nf_log_l2packet to solve this issue.
Fixes: 1fddf4bad0 ("netfilter: nf_log: add packet logging for netdev family")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_UDPLITE is no more a tristate. When set to y, NAT
support for UDPlite protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) |udplite || nf_nat
--------------------------+--------++--------
no builtin | 408048 || 2241312
UDPLITE builtin | - || 2577256
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_SCTP is no more a tristate. When set to y, NAT
support for SCTP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | sctp || nf_nat
--------------------------+--------++--------
no builtin | 428344 || 2241312
SCTP builtin | - || 2597032
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_DCCP is no more a tristate. When set to y, NAT
support for DCCP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | dccp || nf_nat
--------------------------+--------++--------
no builtin | 409800 || 2241312
DCCP builtin | - || 2578968
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b90eb75494 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous commit, modules are going to need to take a
reference on fib info and then drop it using fib_info_put().
Add the fib_info_hold() helper to make the code more readable and also
symmetric with fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_generic() function is both a) inline and b) used ~600 times.
It has the following code inside
...
ptr = ng->ptr[id - 1];
...
"id" is never compile time constant so compiler is forced to subtract 1.
And those decrements or LEA [r32 - 1] instructions add up.
We also start id'ing from 1 to catch bugs where pernet sybsystem id
is not initialized and 0. This is quite pointless idea (nothing will
work or immediate interference with first registered subsystem) in
general but it hints what needs to be done for code size reduction.
Namely, overlaying allocation of pointer array and fixed part of
structure in the beginning and using usual base-0 addressing.
Ids are just cookies, their exact values do not matter, so lets start
with 3 on x86_64.
Code size savings (oh boy): -4.2 KB
As usual, ignore the initial compiler stupidity part of the table.
add/remove: 0/0 grow/shrink: 12/670 up/down: 89/-4297 (-4208)
function old new delta
tipc_nametbl_insert_publ 1250 1270 +20
nlmclnt_lookup_host 686 703 +17
nfsd4_encode_fattr 5930 5941 +11
nfs_get_client 1050 1061 +11
register_pernet_operations 333 342 +9
tcf_mirred_init 843 849 +6
tcf_bpf_init 1143 1149 +6
gss_setup_upcall 990 994 +4
idmap_name_to_id 432 434 +2
ops_init 274 275 +1
nfsd_inject_forget_client 259 260 +1
nfs4_alloc_client 612 613 +1
tunnel_key_walker 164 163 -1
...
tipc_bcbase_select_primary 392 360 -32
mac80211_hwsim_new_radio 2808 2767 -41
ipip6_tunnel_ioctl 2228 2186 -42
tipc_bcast_rcv 715 672 -43
tipc_link_build_proto_msg 1140 1089 -51
nfsd4_lock 3851 3796 -55
tipc_mon_rcv 1012 956 -56
Total: Before=156643951, After=156639743, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is precursor to fixing "[id - 1]" bloat inside net_generic().
Name "s" is chosen to complement name "u" often used for dummy unions.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_ok() consists of 3 clauses:
1) int rem >= (int)sizeof(struct nlattr)
2) u16 nla_len >= sizeof(struct nlattr)
3) u16 nla_len <= int rem
The statement is that clause (1) is redundant.
What it does is ensuring that "rem" is a positive number,
so that in clause (3) positive number will be compared to positive number
with no problems.
However, "u16" fully fits into "int" and integers do not change value
when upcasting even to signed type. Negative integers will be rejected
by clause (3) just fine. Small positive integers will be rejected
by transitivity of comparison operator.
NOTE: all of the above DOES NOT apply to nlmsg_ok() where ->nlmsg_len is
u32(!), so 3 clauses AND A CAST TO INT are necessary.
Obligatory space savings report: -1.6 KB
$ ./scripts/bloat-o-meter ../vmlinux-000* ../vmlinux-001*
add/remove: 0/0 grow/shrink: 3/63 up/down: 35/-1692 (-1657)
function old new delta
validate_scan_freqs 142 155 +13
tcf_em_tree_validate 867 879 +12
dcbnl_ieee_del 328 338 +10
netlbl_cipsov4_add_common.isra 218 215 -3
...
ovs_nla_put_actions 888 806 -82
netlbl_cipsov4_add_std 1648 1566 -82
nl80211_parse_sched_scan 2889 2780 -109
ip_tun_from_nlattr 3086 2945 -141
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add socket family, type and protocol to bpf_sock allowing bpf programs
read-only access.
Add __sk_flags_offset[0] to struct sock before the bitfield to
programmtically determine the offset of the unsigned int containing
protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support hardware offloading when the device given by the tc
rule is different from the Hardware underline device, extract the mirred
(egress) device from the tc action when a filter is added, using the new
tc_action_ops, get_dev().
Flower caches the information about the mirred device and use it for
calling ndo_setup_tc in filter change, update stats and delete.
Calling ndo_setup_tc of the mirred (egress) device instead of the
ingress device will allow a resolution between the software ingress
device and the underline hardware device.
The resolution will take place inside the offloading driver using
'egress_device' flag added to tc_to_netdev struct which is provided to
the offloading driver.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support to a new tc_action_ops.
get_dev is a general option which allows to get the underline
device when trying to offload a tc rule.
In case of mirred action the returned device is the mirred (egress)
device.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a difference between two possible cases:
1. Not offloading tc rule since the user sets 'skip_hw' flag.
2. Not offloading tc rule since the device doesn't support offloading.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jiffies based timestamps allow for easy inference of number of devices
behind NAT translators and also makes tracking of hosts simpler.
commit ceaa1fef65 ("tcp: adding a per-socket timestamp offset")
added the main infrastructure that is needed for per-connection ts
randomization, in particular writing/reading the on-wire tcp header
format takes the offset into account so rest of stack can use normal
tcp_time_stamp (jiffies).
So only two items are left:
- add a tsoffset for request sockets
- extend the tcp isn generator to also return another 32bit number
in addition to the ISN.
Re-use of ISN generator also means timestamps are still monotonically
increasing for same connection quadruple, i.e. PAWS will still work.
Includes fixes from Eric Dumazet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is a large batch of Netfilter fixes for net, they are:
1) Three patches to fix NAT conversion to rhashtable: Switch to rhlist
structure that allows to have several objects with the same key.
Moreover, fix wrong comparison logic in nf_nat_bysource_cmp() as this is
expecting a return value similar to memcmp(). Change location of
the nat_bysource field in the nf_conn structure to avoid zeroing
this as it breaks interaction with SLAB_DESTROY_BY_RCU and lead us
to crashes. From Florian Westphal.
2) Don't allow malformed fragments go through in IPv6, drop them,
otherwise we hit GPF, patch from Florian Westphal.
3) Fix crash if attributes are missing in nft_range, from Liping Zhang.
4) Fix arptables 32-bits userspace 64-bits kernel compat, from Hongxu Jia.
5) Two patches from David Ahern to fix netfilter interaction with vrf.
From David Ahern.
6) Fix element timeout calculation in nf_tables, we take milliseconds
from userspace, but we use jiffies from kernelspace. Patch from
Anders K. Pedersen.
7) Missing validation length netlink attribute for nft_hash, from
Laura Garcia.
8) Fix nf_conntrack_helper documentation, we don't default to off
anymore for a bit of time so let's get this in sync with the code.
I know is late but I think these are important, specifically the NAT
bits, as they are mostly addressing fallout from recent changes. I also
read there are chances to have -rc8, if that is the case, that would
also give us a bit more time to test this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket flags aren't updated atomically, so the socket must be locked
while reading the SOCK_ZAPPED flag.
This issue exists for both l2tp_ip and l2tp_ip6. For IPv6, this patch
also brings error handling for __ip6_datagram_connect() failures.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch measures TCP busy time, which is defined as the period
of time when sender has data (or FIN) to send. The time starts when
data is buffered and stops when the write queue is flushed by ACKs
or error events.
Note the busy time does not include SYN time, unless data is
included in SYN (i.e. Fast Open). It does include FIN time even
if the FIN carries no payload. Excluding pure FIN is possible but
would incur one additional test in the fast path, which may not
be worth it.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the skeleton of the TCP chronograph
instrumentation on sender side limits:
1) idle (unspec)
2) busy sending data other than 3-4 below
3) rwnd-limited
4) sndbuf-limited
The limits are enumerated 'tcp_chrono'. Since a connection in
theory can idle forever, we do not track the actual length of this
uninteresting idle period. For the rest we track how long the sender
spends in each limit. At any point during the life time of a
connection, the sender must be in one of the four states.
If there are multiple conditions worthy of tracking in a chronograph
then the highest priority enum takes precedence over
the other conditions. So that if something "more interesting"
starts happening, stop the previous chrono and start a new one.
The time unit is jiffy(u32) in order to save space in tcp_sock.
This implies application must sample the stats no longer than every
49 days of 1ms jiffy.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bluetooth.h is not part of user API, so __ variants are not neccessary
here.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.
The supported modes: none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stas Nichiporovich reports oops in nf_nat_bysource_cmp(), trying to
access nf_conn struct at address 0xffffffffffffff50.
This is the result of fetching a null rhash list (struct embedded at
offset 176; 0 - 176 gets us ...fff50).
The problem is that conntrack entries are allocated from a
SLAB_DESTROY_BY_RCU cache, i.e. entries can be free'd and reused
on another cpu while nf nat bysource hash access the same conntrack entry.
Freeing is fine (we hold rcu read lock); zeroing rhlist_head isn't.
-> Move the rhlist struct outside of the memset()-inited area.
Fixes: 7c96643519 ("netfilter: move nat hlist_head to nf_conn")
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As Liping Zhang reports, after commit a8b1e36d0d ("netfilter: nft_dynset:
fix element timeout for HZ != 1000"), priv->timeout was stored in jiffies,
while set->timeout was stored in milliseconds. This is inconsistent and
incorrect.
Firstly, we already call msecs_to_jiffies in nft_set_elem_init, so
priv->timeout will be converted to jiffies twice.
Secondly, if the user did not specify the NFTA_DYNSET_TIMEOUT attr,
set->timeout will be used, but we forget to call msecs_to_jiffies
when do update elements.
Fix this by using jiffies internally for traditional sets and doing the
conversions to/from msec when interacting with userspace - as dynset
already does.
This is preferable to doing the conversions, when elements are inserted or
updated, because this can happen very frequently on busy dynsets.
Fixes: a8b1e36d0d ("netfilter: nft_dynset: fix element timeout for HZ != 1000")
Reported-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Anders K. Pedersen <akp@cohaesio.com>
Acked-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I got offlist bug report about failing connections and high cpu usage.
This happens because we hit 'elasticity' checks in rhashtable that
refuses bucket list exceeding 16 entries.
The nat bysrc hash unfortunately needs to insert distinct objects that
share same key and are identical (have same source tuple), this cannot
be avoided.
Switch to the rhlist interface which is designed for this.
The nulls_base is removed here, I don't think its needed:
A (unlikely) false positive results in unneeded port clash resolution,
a false negative results in packet drop during conntrack confirmation,
when we try to insert the duplicate into main conntrack hash table.
Tested by adding multiple ip addresses to host, then adding
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
... and then creating multiple connections, from same source port but
different addresses:
for i in $(seq 2000 2032);do nc -p 1234 192.168.7.1 $i > /dev/null & done
(all of these then get hashed to same bysource slot)
Then, to test that nat conflict resultion is working:
nc -s 10.0.0.1 -p 1234 192.168.7.1 2000
nc -s 10.0.0.2 -p 1234 192.168.7.1 2000
tcp .. src=10.0.0.1 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1024 [ASSURED]
tcp .. src=10.0.0.2 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1025 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1234 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2001 src=192.168.7.1 dst=192.168.7.10 sport=2001 dport=1234 [ASSURED]
[..]
-> nat altered source ports to 1024 and 1025, respectively.
This can also be confirmed on destination host which shows
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1024
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1025
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1234
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: 870190a9ec ("netfilter: nat: convert nat bysrc hash to rhashtable")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The undo_cwnd fallback in the stack doubles cwnd based on ssthresh,
which un-does reno halving behaviour.
It seems more appropriate to let congctl algorithms pair .ssthresh
and .undo_cwnd properly. Add a 'tcp_reno_undo_cwnd' function and wire it
up for all congestion algorithms that used to rely on the fallback.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument to get_net_ns_by_fd() is a /proc/$PID/ns/net file
descriptor not a pid. Fix the typo.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP busy polling is restricted to connected UDP sockets.
This is because sk_busy_loop() only takes care of one NAPI context.
There are cases where it could be extended.
1) Some hosts receive traffic on a single NIC, with one RX queue.
2) Some applications use SO_REUSEPORT and associated BPF filter
to split the incoming traffic on one UDP socket per RX
queue/thread/cpu
3) Some UDP sockets are used to send/receive traffic for one flow, but
they do not bother with connect()
This patch records the napi_id of first received skb, giving more
reach to busy polling.
Tested:
lpaa23:~# echo 70 >/proc/sys/net/core/busy_read
lpaa24:~# echo 70 >/proc/sys/net/core/busy_read
lpaa23:~# for f in `seq 1 10`; do ./super_netperf 1 -H lpaa24 -t UDP_RR -l 5; done
Before patch :
27867 28870 37324 41060 41215
36764 36838 44455 41282 43843
After patch :
73920 73213 70147 74845 71697
68315 68028 75219 70082 73707
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp transport rhashtable uses hash(lport, dport, daddr) as the key
to hash a node to one chain. If in one host thousands of assocs connect
to one server with the same lport and different laddrs (although it's
not a normal case), all the transports would be hashed into the same
chain.
It may cause to keep returning -EBUSY when inserting a new node, as the
chain is too long and sctp inserts a transport node in a loop, which
could even lead to system hangs there.
The new rhlist interface works for this case that there are many nodes
with the same key in one chain. It puts them into a list then makes this
list be as a node of the chain.
This patch is to replace rhashtable_ interface with rhltable_ interface.
Since a chain would not be too long and it would not return -EBUSY with
this fix when inserting a node, the reinsert loop is also removed here.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the lwtunnel_headroom() function which is called
in ipv4_mtu() and ip6_mtu(), to also return the correct headroom
value when the lwtunnel state is OUTPUT_REDIRECT.
This patch enables e.g. SR-IPv6 encapsulations to work without
manually setting the route mtu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sk_busy_loop() can schedule by itself, we can remove
need_resched() check from sk_can_busy_loop()
Also add a const to its struct sock parameter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the FIB offload infrastructure was a bit too
aggressive and also removed code needed to clean up us splitting the table
if additional rules were added. Specifically the function
fib_trie_flush_external was called at the end of a new rule being added to
flush the foreign trie entries from the main trie.
I updated the code so that we only call fib_trie_flush_external on the main
table so that we flush the entries for local from main. This way we don't
call it for every rule change which is what was happening previously.
Fixes: 347e3b28c1 ("switchdev: remove FIB offload infrastructure")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rolf Neugebauer reported very long delays at netns dismantle.
Eric W. Biederman was kind enough to look at this problem
and noticed synchronize_net() occurring from netif_napi_del() that was
added in linux-4.5
Busy polling makes no sense for tunnels NAPI.
If busy poll is used for sessions over tunnels, the poller will need to
poll the physical device queue anyway.
netif_tx_napi_add() could be used here, but function name is misleading,
and renaming it is not stable material, so set NAPI_STATE_NO_BUSY_POLL
bit directly.
This will avoid inserting gro_cells napi structures in napi_hash[]
and avoid the problematic synchronize_net() (per possible cpu) that
Rolf reported.
Fixes: 93d05d4a32 ("net: provide generic busy polling to all NAPI drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 850cbaddb5 ("udp: use it's own memory accounting schema")
assumes that the socket proto has memory accounting enabled,
but this is not the case for UDPLITE.
Fix it enabling memory accounting for UDPLITE and performing
fwd allocated memory reclaiming on socket shutdown.
UDP and UDPLITE share now the same memory accounting limits.
Also drop the backlog receive operation, since is no more needed.
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Reported-by: Andrei Vagin <avagin@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 14135f30e3 ("inet: fix sleeping inside inet_wait_for_connect()"),
sk_wait_event() needs to fix too, because release_sock() is blocking,
it changes the process state back to running after sleep, which breaks
the previous prepare_to_wait().
Switch to the new wait API.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen