Limit the no-streams case to speeds less then USB_SPEED_SUPER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of uas_pre_reset is to:
1) Stop any new commands from being submitted while an externally triggered
usb-device-reset is running
2) Wait for any pending commands to finish before allowing the usb-device-reset
to continue
The purpose of uas_suspend is to:
2) Wait for any pending commands to finish before suspending
This commit fixes races in both paths:
1) For 1) we use scsi_block_requests, but the scsi midlayer calls queuecommand
without holding any locks, so a queuecommand may already past the midlayer
scsi_block_requests checks when we call it, add a check to uas_queuecommand
to fix this
2) For 2) we were waiting for all sense-urbs to complete, there are 2 problems
with this approach:
a) data-urbs may complete after the sense urb, so we need to check for those
too
b) if a sense-urb completes with a iu id of READ/WRITE_READY a command is not
yet done. We submit a new sense-urb immediately in this case, but that
submit may fail (in which case it will get retried by uas_do_work), if this
happens the sense_urbs anchor may become empty while the cmnd is not yet
done
Also unblock requests on timeout, to avoid things getting stuck in that case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all urbs we've allocated are necessarily also submitted, non-submitted
urbs will not be free-ed by their completion handler. So we need to free
them manually.
There are 2 scenarios where this can happen:
1) We have failed to submit some urbs at abort / disconnect
2) When running over usb-2 we may have never tried to submit the data urbs
when completing the scsi cmnd, because we never got a READ/WRITE_READY iu
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not keep references around to a cmnd which is under error handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not strictly necessary for the cmd urb to have a reference to the
cmnd, and without this reference it becomes easier to drop all references to
a cmnd on an abort.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've the same info doubled in both the inflight list and the cmnd array,
drop the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data urbs are all killed before calling zap_pending, and their completion
handler should have cleared their inflight flag.
Do not 0 the data inflight flags, and add a check for try_complete succeeding,
as it should always succeed when called from zap_pending.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the whole dance with first moving cmnds to a dead-list. The resetting
flag ensures that no new cmds / urbs will be submitted, and that any urb
completions are short-circuited without trying to complete the scsi cmnd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we no longer drop our lock to unlink the data urbs, we can simply
free them on completion, making their handling consistent with the other urbs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for all the trickery with dropping the lock, we can
simply reference the urbs while we hold the lock to ensure the urbs don't
disappear beneath us, and do the actual unlink (+ unreference) after we've
dropped the lock.
This also fixes a race where we may loose of cmnd ownership to the scsi
midlayer without holding the lock due to the midlayer re-claiming ownership
through an abort (which will be handled by a future patch in this series).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status urb should not complete before the command has been submitted, nor
should we get a second status urb for the same tag after a IU_ID_STATUS.
Data urbs should not complete before the command has been submitted, but may
complete after the IU_ID_STATUS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using scsi_host_find_tag with tags returned by the device is unsafe for
multiple reasons:
1) It returns tags->rqs[tag], which may be non NULL even when the cmnd is
not owned by us
2) It returns tags->rqs[tag], without holding any locks protecting it
3) It returns tags->rqs[tag], without doing any boundary checking
Instead keep our own list which maps tags -> inflight cmnds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out the mapping of scsi-tags -> uas-tags/stream-ids to a helper function
so that there is a single place where this "magic" happens.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Make sure we always hold the lock when setting / checking resetting
- Check resetting before checking urb->status
- Add missing check for resetting to uas_data_cmplt
- Add missing check for resetting to uas_do_work
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are various bug reports about oopses / hangs with the uas driver,
which all point to the abort-command and logical-unit-reset (task-management)
error handling paths.
Getting these right is very hard, there are quite a few corner cases, and
testing is almost impossible since under normal operation these code paths
are not used at all.
Another problem is that there are also some cases where it simply is not clear
what to do at all. E.g. over usb-2 multiple outstanding commands share the same
endpoint. What if a command gets aborted while its sense urb is half way
through completing (so some data has been transfered but not all). Since the
urb is not yet complete we don't know if the sense urb is actually for this
command, or for one of the other oustanding commands. If it is for one of the
other commands and we cancel it, then we end up in an undefined state. But if
it is actually for the command we're aborting, and the abort succeeds, then it
may never complete...
This exact same problem applies to logical unit resets too, if there are
multiple luns, then commands outstanding on both luns share the sense
endpoint. If there is only a single lun, then doing a logical unit reset is
little better then doing a full usb device reset.
So summarizing because:
1) abort / lun-reset is very tricky to get right
2) Not being able to test the tricky code, which means it will have bugs
3) This being a code path which under normal operation will never happen,
so being slow / sub-optimal here is not really an issue
4) Under error conditions we will still be able to recover through usb
device resets.
5) This may be a bit slower in some cases, but this is actually faster in
cases where the bridge ship has locked up, which seems to be the most
common error case sofar.
This commit removes the abort / lun-reset error handling paths, and also the
taks-mgmt code since those are the only 2 task-mgmt users. Leaving only the
(tested and testable) usb-device-reset error handling path in place.
Note I realize that this is somewhat of a big hammer, but currently people
are seeing very hard to debug oopses with uas. First let focus on making uas
work reliable, then we can later look into adding more fine grained error
handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As most ASM1051 based devices, this one has unfixable issues with uas too.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on some architecture spin_is_locked() always return false in
uniprocessor configuration and therefore it would be advise
to replace with lockdep_assert_held().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the ehci-st.c and ohci-st.c files for the usb 2.0
& usb1.1 host controller drivers found on stih41x and stih4xx STMicroelectronics
SoC's into the STI arch section of the maintainers file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for
the ohci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for the
ehci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the glue code required to ensure the on-chip OHCI
controller works on STi consumer electronics SoC's from STMicroelectronics.
It mainly manages the setting and enabling of the relevant clocks and manages
the reset / power signals to the IP block.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the glue code required to ensure the on-chip EHCI
controller works on STi consumer electronics SoC's from STMicroelectronics.
It mainly manages the setting and enabling of the relevant clocks and manages
the reset / power signals to the IP block.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource to simplify error handling in the probe
function and to get rid of some boilerplate in the remove function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds chipidea to the list of DT vendor prefixes.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some kernel-doc style comment are not satisfied for format, fix them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TPL (Targeted Peripheral List) is needed for targets host
(OTG and Embedded Hosts) for usb certification and other
vendor specific requirements.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update configuration for USB_OTG_WHITELIST, any targeted hosts
(non PC-hosts) can have TPL (Targered Peripheral List).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to On-The-Go and Embedded Host Supplement to the USB Revision
2.0 Specification, the targeted hosts (non-PC hosts) include both
embedded hosts and otg, and each targeted host product defines the
set of supported peripherals on a TPL (Targeted Peripheral List). So,
TPL should apply for both OTG and embedded host, and the otg support is
not a must for embedded host.
The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST
has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration
fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The targeted hosts (non-PC hosts) need to have TPL (Targeted Peripheral List)
for USB OTG & EH certification and other vendor specific requirements.
The platform who needs TPL feature should set this flag at usb host
controller driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2267089ea.
That commit causes more problem than fixes. Firstly, kfree()
should be called after usb_ep_dequeue() and secondly, the way
things are, we will try to dequeue a request that has already
completed much more frequently than one which is pending.
Cc: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.17
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes add two new "simple" drivers, while removing the redundant
zte_ev driver (PIDs moved to option).
Included are also some minor clean ups to the xsens_mt driver, and the
enabling of further baud rates for pl2303 devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HsW7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.18-rc1
These changes add two new "simple" drivers, while removing the redundant
zte_ev driver (PIDs moved to option).
Included are also some minor clean ups to the xsens_mt driver, and the
enabling of further baud rates for pl2303 devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull ARM fixes from Russell King:
"Fixes for ARM, the most notable being the fix from Nathan Lynch to fix
the state of various registers during execve, to ensure that data
can't be leaked between two executables.
Fixes from Victor Kamensky for get_user() on big endian platforms,
since the addition of 8-byte get_user() support broke these fairly
badly.
A fix from Sudeep Holla for affinity setting when hotplugging CPU 0.
A fix from Stephen Boyd for a perf-induced sleep attempt while atomic.
Lastly, a correctness fix for emulation of the SWP instruction on
ARMv7+, and a fix for wrong carry handling when updating the
translation table base address on LPAE platforms"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8149/1: perf: Don't sleep while atomic when enabling per-cpu interrupts
ARM: 8148/1: flush TLS and thumbee register state during exec
ARM: 8151/1: add missing exports for asm functions required by get_user macro
ARM: 8137/1: fix get_user BE behavior for target variable with size of 8 bytes
ARM: 8135/1: Fix in-correct barrier usage in SWP{B} emulation
ARM: 8133/1: use irq_set_affinity with force=false when migrating irqs
ARM: 8132/1: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsEN
-----END PGP SIGNATURE-----
Merge tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"some media bug fixes:
- a Kconfig dependency issue
- some fixes for af9033/it913x demod to be more reliable and address
a performance regression
- cx18: fix an oops on devices with tda8290 tuner
- two new USB IDs for af9035
- a couple fixes on smapp driver"
* tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] af9035: new IDs: add support for PCTV 78e and PCTV 79e
[media] af9033: feed clock to RF tuner
[media] it913x: init tuner on attach
[media] af9033: update IT9135 tuner inittabs
[media] Kconfig: do not select SPI bus on sub-driver auto-select
[media] cx18: fix kernel oops with tda8290 tuner
[media] smiapp: Set sub-device owner
[media] smiapp: Fix power count handling
Here are some IIO and Staging driver fixes for 3.17-rc6. They are all
pretty simple, and resolve reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQdukgACgkQMUfUDdst+ymENwCfTYAbHywZxtdQRMQ+ByfAeQY4
5kIAnjb6xVPATRL9DMt/cUfyE550SiEz
=UW80
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO fixes from Greg KH:
"Here are some IIO and Staging driver fixes for 3.17-rc6. They are all
pretty simple, and resolve reported issues"
* tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: buffer overflow in ioctl
iio:magnetometer: bugfix magnetometers gain values
iio: adc: at91: don't use the last converted data register
iio: adc: xilinx-xadc: assign auxiliary channels address correctly
iio: meter: ade7758: Fix indio_dev->trig assignment
iio: inv_mpu6050: Fix indio_dev->trig assignment
iio: gyro: itg3200: Fix indio_dev->trig assignment
iio: st_sensors: Fix indio_dev->trig assignment
iio: hid_sensor_hub: Fix indio_dev->trig assignment
iio: adc: ad_sigma_delta: Fix indio_dev->trig assignment
iio: accel: bma180: Fix indio_dev->trig assignment
iio:trigger: modify return value for iio_trigger_get
iio:inkern: fix overwritten -EPROBE_DEFER in of_iio_channel_get_by_name
Here are some USB and PHY fixes and quirks for 3.17-rc6. Nothing major,
just a few things that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQduf0ACgkQMUfUDdst+ylJdwCaAnzHvU6geu1tINSYpk0/XNKE
SgEAoJcaG0Nswpm5gKrJZbX0JstagIgn
=JOUD
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes / quirks from Greg KH:
"Here are some USB and PHY fixes and quirks for 3.17-rc6. Nothing
major, just a few things that have been reported"
* tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
phy: spear1340-miphy: fix driver dependencies
phy: spear1310-miphy: fix driver dependencies
phy: miphy365x: Fix off-by-one error
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target pending fixes for v3.17-rc6.
Included are Sagi's long overdue fixes related to iser-target
shutdown, along with a couple of fixes from Sebastian related to ALUA
Referrals changes that when in during the v3.14 time-frame.
Also included are a few iscsi-target fixes, most recently of which
where found during Joern's Coverity scanning of target code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: avoid NULL pointer in iscsi_copy_param_list failure
iscsi-target: Fix memory corruption in iscsit_logout_post_handler_diffcid
target: Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE
target: Fix user data segment multiplier in spc_emulate_evpd_b3()
iscsi-target: Ignore ICF_GOT_LAST_DATAOUT during Data-Out ITT lookup
Target/iser: Fix initiator_depth and responder_resources
Target/iser: Avoid calling rdma_disconnect twice
Target/iser: Don't put isert_conn inside disconnected handler
Target/iser: Get isert_conn reference once got to connected_handler
Pull drm fixes from Dave Airlie:
"A bunch of radeon fixes for oops on module unload, and problems with
resetting the dma engine, one nouveau fix for black boxes in rendering
on my mbp retina, one sti fix, and a couple of intel fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
drm/radeon: delete unused PTE_* defines
drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
drm: sti: do not iterate over the info frame array
drm/i915: Fix SRC_COPY width on 830/845g
A mismatch between FB and LTC's idea of how big a large page is causes
issues such as black "holes" in rendering to occur on some boards
(those where LTC is configured for 64KiB large pages) when compression
is used.
Confirmed to fix at least the GK107 MBP.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
single fix for regression on rs4xx/rs690/rs740
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
Hans de Goede