drivers/thermal/tango_thermal.c:86:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In some of platform, thermal sensors like NCT thermistors are
connected to the one of ADC channel. The temperature is read by
reading the voltage across the sensor resistance via ADC. Lookup
table for ADC read value to temperature is referred to get
temperature. ADC is read via IIO framework.
Add support for thermal sensor driver which read the voltage across
sensor resistance from ADC through IIO framework.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There has a static checker warning:
warn: variable dereferenced before check 'dev' (see line 222)
Since check 'dev' is unnecessary, so remove this check.
Fixes: ee6d79f202a4 ("thermal: tegra: add thermtrip function")
Signed-off-by: Wei Ni <wni@nvidia.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
After the PM support has been added to this driver, we get
a harmless warning when that support is disabled at compile
time:
drivers/thermal/tegra/soctherm.c:641:12: error: 'soctherm_resume' defined but not used [-Werror=unused-function]
static int soctherm_resume(struct device *dev)
This marks the two PM functions as __maybe_unused to shut up
the warning. This is preferred over adding an #ifdef around
them, as it is harder to get wrong, and provides better
compile-time coverage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a134b4143b65 ("thermal: tegra: add PM support")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Tango thermal driver provides support for the primitive temperature
sensor embedded in Tango chips since the SMP8758.
This sensor only generates a 1-bit signal to indicate whether the die
temperature exceeds a programmable threshold.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When register sensors into thermal zone during initialization phase, it
reports error for IRQ imbalance enabling:
[ 2.040713] WARNING: at kernel/irq/manage.c:513
[ 2.040719] Modules linked in:
[ 2.040721]
[ 2.040729] CPU: 1 PID: 804 Comm: irq/33-hisi_the Not tainted 4.5.0-rc4+ #505
[ 2.040732] Hardware name: HiKey Development Board (DT)
[ 2.040736] task: ffffffc03ae82580 ti: ffffffc0379c8000 task.ti: ffffffc0379c8000
[ 2.040745] PC is at __enable_irq+0x74/0x84
[ 2.040749] LR is at __enable_irq+0x74/0x84
This warning is for IRQ imbalance enabling, which is caused by
enable_irq() twice. During sensor's initialization it tries to enable
IRQ, the driver will call thermal_zone_of_sensor_register() to bind
sensors and read sensor's temperature. But at this moment the flag
"data->irq_enabled" has been not initialized as correct state, so it
finally introduces the function enabled_irq() to be called twice. In
essentially this is caused by the flag "data->irq_enabled" is
inconsistent with real hardware IRQ enabling state.
So this patch is to fix this issue, firstly init "irq_enabled" flag
before binding sensors to thermal zone. Also change to use the function
irq_get_irqchip_state() to read back real interrupt line state.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In current code sensor driver registers all 4 sensors together and if
any of them has not bound to thermal zone successfully then driver will
return failure for driver's initialization. As a result, if DT binds
thermal zone with only one sensor, then the thermal driver will not work
well anymore.
So this patch is to fix this issue. It allows the thermal sensor driver
can register any number sensors at initialization phase, and fix up code
for other related code to skip related sensor's accessing if the sensor
has not been enabled in initialization phase.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Handle HW initialization in one function soctherm_init(),
so that the codes are more clear.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Handle clock enable/disable codes in one function
soctherm_clk_enable(), so that the codes are more clear.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for hardware critical thermal limits to the
SOC_THERM driver. It use the Linux thermal framework to
create critical trip temp, and set it to SOC_THERM hardware.
If these limits are breached, the chip will reset, and if
appropriately configured, will turn off the PMIC.
This support is critical for safe usage of the chip.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In current of-thermal, the .set_trip_temp only support to
set trip_temp for SW. But some sensors support to set
trip_temp on hardware, so that can trigger interrupt,
shutdown or any other events.
This patch adds .set_trip_temp() callback in
thermal_zone_of_device_ops{}, so that the sensor device can
use it to set trip_temp on hardware.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a debugfs interface to show register contents for debug.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Split most of the Tegra124 data and code into a Tegra124-specific
file.
Split most of the fuse-related code into a fuse-related source file.
This is in preparation for adding a Tegra210-specific driver in a
future patch.
Beyond the maintainability improvements, this is intended to separate
chip-specific ATE and characterization-related hacks into chip-specific
files, in the hopes that they won't pollute code for other chips.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Get rid of T124-specific PDIV/HOTSPOT hack.
tegra-soctherm.c contained a hack to set the SENSOR_PDIV and
SENSOR_HOTSPOT_OFFSET registers - it just did two writes of
T124-specific opaque values. Convert these into a form that can be
substituted on a per-chip basis, and into structure fields that have
at least some independent meaning.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Combine sensor group-related data structures into struct
tegra_tsensor_group. This provides a single location for
sensor group data storage.
More sensor group data will be added in subsequent patches.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Move Tegra soctherm driver to tegra directory, it's easy to maintain
and add more new function support for Tegra platforms.
This will also help to split soctherm driver into common parts and
chip specific data related parts.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_node_put is iterating through all terms in the tbps array even though
the bind has failed. We need to only iterate through the terms that have
already passed the binding step.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ulises Brindis <brindisu@lab126.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When performing a suspend operation, the kernel brings all of the
non-boot CPUs offline, calling the hot plug notifiers with the flag,
CPU_TASKS_FROZEN, set in the action code. Similarly, during resume,
the CPUs are brought back online, but again the notifiers have the
FROZEN flag set.
While some very few drivers really need to treat suspend/resume
specially, this driver unintentionally ignores the notifications.
This patch changes the driver to cancel its work item when the CPU
goes down, even during a suspend operation. As a result, the
suspended state is no longer a special case.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Bang-bang thermal governor uses trip point hysteresis to make decisions.
Hysteresis is a required property in the device tree for trip points, but it is
an optional thermal zone device operation. Hence, we need to check whether the
function pointer is valid or not.
If it is not available, we assume the hysteresis to be zero. Consequently, a
highly varying temperature will make the governor continuosly switch a cooling
device ON and OFF.
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
CC: Peter Feuerer <peter@piie.net>
Signed-off-by: Michele Di Giorgio <michele.digiorgio@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
INT3406 ACPI device object resembles an ACPI video output device, but its
_BCM is said to be deprecated and should not be used. So we will make
use of the raw interface to do the actual cooling.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BIOS/EC can change PPCC element dynamically and inform OS about the change.
When this driver receives notification, it will read PPCC element again.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Powerclamp works by aligning idle time to achieve package level
idle states, aka cstates. As long as one of the package cstates
is available, synchronized idle injection is meaningful.
This patch replaces the CPU whitelist with CPU feature and
package cstate counter check such that we don't have to modify
this whitelist for every new CPU.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Power allocator's parameters are S32 type, so use %d to print them.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When calculate temperature, old code firstly do division and then
convert to "millicelsius" unit. This will lose resolution and only can
read back temperature with "Celsius" unit.
So firstly scale step value to "millicelsius" and then do division, so
finally we can increase resolution for temperature value. Also refine
the calculation from temperature value to step value.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
At least with CONFIG_COMPILE_TEST, there's no reason to assume
that CONFIG_RESET_CONTROLLER is set, but the code for this
controller requires it since it calls device_reset().
Make CONFIG_MTK_THERMAL properly depend on CONFIG_RESET_CONTROLLER.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The commit 17e8351a77 consistently use int for temperature,
however it missed a few in trip temperature and thermal_core.
In current codes, the trip->temperature used "unsigned long"
and zone->temperature used"int", if the temperature is negative
value, it will get wrong result when compare temperature with
trip temperature.
This patch can fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
req_range is declared as a u64 to cope with overflows in the
multiplication of two u32. As both req_power and power_range are u32,
we need to make sure the multiplication is done with u64 types.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add __init attribute on a function that is only called from other __init
functions and that is not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the function is put in the
.text.unlikely segment. Declaring it as __init will cause it to be put in
the .init.text and to disappear after initialization.
The result of objdump -x on the function before the change is as follows:
0000000000000086 l F .text.unlikely 0000000000000739 thermal_of_build_thermal_zone
And after the change it is as follows:
0000000000000000 l F .init.text 0000000000000734 thermal_of_build_thermal_zone
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In some cases, platform thermal driver may report invalid trip points,
thermal core should not take any action for these trip points.
This fixed a regression that bogus trip point starts to screw up thermal
control on some Lenovo laptops, after
commit bb431ba26c
Author: Zhang Rui <rui.zhang@intel.com>
Date: Fri Oct 30 16:31:47 2015 +0800
Thermal: initialize thermal zone device correctly
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
CC: <stable@vger.kernel.org> #3.18+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317190
Link: https://bugzilla.kernel.org/show_bug.cgi?id=114551
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enabled temperature reporting device of Skylake Platform Controller hub.
The register map is same as the wildcat point thermal currently implemented
in this driver.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add resource managed version of thermal_zone_of_sensor_register() and
thermal_zone_of_sensor_unregister().
This helps in reducing the code size in error path, remove of
driver remove callbacks and making proper sequence for deallocations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The driver doesn't check if the regulator_get_optional return value is
-EPROBE_DEFER so it will wrongly assume that the regulator couldn't be
found just because the regulator driver wasn't registered yet, i.e:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
In this case the return value should be propagated to allow the driver
probe function to be deferred until the regulator driver is registered.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Exynos TMU DT binding says that the vtmu-supply is optional but the
driver uses devm_regulator_get() that creates a dummy regulator if it's
not defined in the DT. For example the following message is in the log:
10060000.tmu supply vtmu not found, using dummy regulator
Use the optional version of regulator_get() that doesn't create a dummy
regulator and instead returns a -ENODEV errno code. Since it's expected
that a regulator may not be defined and the driver will inform about it:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When DeviveTree contains more trip-points than SoC can configure
(usually more than four) and polling mode is not enabled, then the
remaining trip-points will be silently ignored. No interrupts will be
generated for them.
This might be quite dangerous when one provides DTB with a
non-configurable critical trip-point, like (assuming four supported
thresholds in TMU):
- alert @50 C (type: active),
- alert @60 C (type: active),
- alert @70 C (type: active),
- alert @80 C (type: active),
- critical @120 C (type: critical) <- no interrupts generated.
This is a mistake in DTB so print a message in such case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The sign bit of temperature readback is bit 0, not bit 1.
Change to BIT(0) to fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Matt Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:
drivers/built-in.o: In function `kirkwood_thermal_probe':
kirkwood_thermal.c:(.text+0x390a25): undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `exynos_tmu_probe':
exynos_tmu.c:(.text+0x39246b): undefined reference to `devm_ioremap'
The users of devm_ioremap_resource() which are compile-testable should
depend on HAS_IOMEM.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We don't need to initialize "ret". We can move the IS_ERR() checks into
the if condition instead of doing an assignment first. Also there is a
check for "ret" when we know it is zero so we can remove that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This driver only has runtime but no build time dependencies, so it can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As the TRM says, add the tsadc_q_sel to control the temperature-code
sequence since the rk3228/rk3399 need set this bit (1024 - tsadc_q)
as output.
Fixes: commit
b0d7033 "thermal: rockchip: Support the RK3399 SoCs in thermal driver"
7b02a5e "thermal: rockchip: Support the RK3228 SoCs in thermal driver"
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch renames to be more adapter compatibles since more and more
SoCs are supported in thermal driver.
Reported-by: Huang,Tao <huangtao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
the calculation use a global table, not their own table.
so adapt the table to the correct one.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.
Fixes: commit 437df2172e
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for the Mediatek thermal controller found on MT8173
and likely other SoCs.
The controller is a bit special. It does not have its own ADC, instead
it controls the on-SoC AUXADC via AHB bus accesses. For this reason
we need the physical address of the AUXADC. Also it controls a mux
using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In __cpufreq_cooling_register() we allocate the arrays for time_in_idle
and time_in_idle_timestamp to be as big as the number of cpus in this
cpufreq device. However, in get_load() we access this array using the
cpu number as index, which can result in an out of bound access.
Index time_in_idle{,_timestamp} using the index in the cpufreq_device's
allowed_cpus mask, as we do for the load_cpu array in
cpufreq_get_requested_power()
Reported-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When the thermal subsystem is a loadable module, the u8500 driver
fails to build:
drivers/thermal/built-in.o: In function `db8500_thermal_probe':
db8500_thermal.c:(.text+0x96c): undefined reference to `thermal_zone_device_register'
drivers/thermal/built-in.o: In function `db8500_thermal_work':
db8500_thermal.c:(.text+0xab4): undefined reference to `thermal_zone_device_update'
This changes the symbol to a tristate, so Kconfig can track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When the thermal subsystem is a loadable module, the spear driver
fails to build:
drivers/thermal/built-in.o: In function `spear_thermal_exit':
spear_thermal.c:(.text+0xf8): undefined reference to `thermal_zone_device_unregister'
drivers/thermal/built-in.o: In function `spear_thermal_probe':
spear_thermal.c:(.text+0x230): undefined reference to `thermal_zone_device_register'
This changes the symbol to a tristate, so Kconfig can track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The spear thermal driver hides its suspend/resume function conditionally
based on CONFIG_PM, but references them based on CONFIG_PM_SLEEP, so
we get a warning if the former is set but the latter is not:
thermal/spear_thermal.c:58:12: warning: 'spear_thermal_suspend' defined but not used [-Wunused-function]
thermal/spear_thermal.c:75:12: warning: 'spear_thermal_resume' defined but not used [-Wunused-function]
This removes the #ifdef and instead uses a __maybe_uninitialized
annotation to avoid the warning and improve compile-time coverage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch enables to use thermal-zone on DT if it was calles as
"renesas,rcar-thermal-gen2".
Previous style (= non thermal-zone) is still supported by
"renesas,rcar-thermal" to keep compatibility for "git bisect".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Use for_each_available_child_of_node() for iterating over each
available child instead of iterating over each child and then
checking their status.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Zhang Rui:
"The top merge commit was re-generated yesterday because two topic
branches were dropped from this pull request in the last minute due to
some unaddressed comments. All the other material has been in
linux-next for quite a while.
Specifics:
- Enhance thermal core to handle unexpected device cooling states
after fresh boot and system resume. From Zhang Rui and Chen Yu.
- Several fixes and cleanups on Rockchip and RCAR thermal drivers.
From Caesar Wang and Kuninori Morimoto.
- Add Broxton support for Intel processor thermal reporting device
driver. From Amy Wiles"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: trip_point_temp_store() calls thermal_zone_device_update()
thermal: rcar: rcar_thermal_get_temp() return error if strange temp
thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
thermal: rcar: check every rcar_thermal_update_temp() return value
thermal: rcar: move rcar_thermal_dt_ids to upside
thermal: rockchip: Support the RK3399 SoCs in thermal driver
thermal: rockchip: Support the RK3228 SoCs in thermal driver
dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
thermal: rockchip: fix a trivial typo
Thermal: Enable Broxton SoC thermal reporting device
thermal: constify pch_dev_ops structure
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
Current rcar thermal driver sometimes checks irq possibility when it
calls rcar_thermal_irq_enable/disable(), but sometimes not.
This patch checks it inside rcar_thermal_irq_enable/disable().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Every rcar_thermal_update_temp() return value will be checked.
And also, rcar_thermal_get_temp() always call
rcar_thermal_update_temp() by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch is prepare for of-thermal support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3399 SoCs have two Temperature Sensors, channel 0 is for CPU.
channel 1 is for GPU.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3228 SoCs has one Temperature Sensor, channel 0 is for CPU.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patchset trys to dictate unified format for driver.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The pch_dev_ops structure is never modified. It is only stored in a field
that is already declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When a new cooling device is registered, we need to update the
thermal zone to set the new registered cooling device to a proper
state.
This fixes a problem that the system is cool, while the fan devices
are left running on full speed after boot, if fan device is registered
after thermal zone device.
Here is the history of why current patch looks like this:
https://patchwork.kernel.org/patch/7273041/
CC: <stable@vger.kernel.org> #3.18+
Reference:https://bugzilla.kernel.org/show_bug.cgi?id=92431
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Current thermal code does not handle system sleep well because
1. the cooling device cooling state may be changed during suspend
2. the previous temperature reading becomes invalid after resumed because
it is got before system sleep
3. updating thermal zone device during suspending/resuming
is wrong because some devices may have already been suspended
or may have not been resumed.
Thus, the proper way to do this is to cancel all thermal zone
device update requirements during suspend/resume, and after all
the devices have been resumed, reset and update every registered
thermal zone devices.
This also fixes a regression introduced by:
Commit 19593a1fb1 ("ACPI / fan: convert to platform driver")
Because, with above commit applied, all the fan devices are attached
to the acpi_general_pm_domain, and they are turned on by the pm_domain
automatically after resume, without the awareness of thermal core.
CC: <stable@vger.kernel.org> #3.18+
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=78201
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=91411
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
CC: <stable@vger.kernel.org> #3.18+
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP which
is valid for all IMX6 SoC's (despite the fact that the IMXSDLRM and
IMXSXRM do not document this - this has been proven via tests as well as
verified by Freescale FAE).
Instead of assuming a fixed 85C for passive cooling threshold and 105C for
critical use the thermal grade for these configurations.
We will set the critical to maxT - 5C and passive to maxT - 10C.
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
----
v3:
- rebase against linux-soc-thermal.git
- added ack's from Shawn and Jon
v2:
- remove check for IMX6Q and update comments: The OTP values have been tested
on IMX6SOLO, IMX6DUALLITE, and IMX6SX and Freescale FAE has shared data with
me that the OTP settings are the same and that the reference manuals will
reflect this in their next updates.
- set critical to max - 5C
- set passive to max - 10C
- display max temp in info
- do not allow passive to be set above critical
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This just caused build errors:
warning: (QCOM_SPMI_TEMP_ALARM) selects REGMAP_SPMI which has unmet direct dependencies (SPMI)
drivers/built-in.o: In function `regmap_spmi_ext_gather_write':
:(.text+0x609b0): undefined reference to `spmi_ext_register_write'
:(.text+0x609f0): undefined reference to `spmi_ext_register_writel'
While it's generally a good idea to allow compile testing, in this
case, it just doesn't work, so reverting the patch that
introduced the compile-test variant seems the most appropriate
solution.
Note that SPMI also has a 'depends on ARCH_QCOM || COMPILE_TEST'
statement, so we should be able to enable SPMI on all architectures
for compile testing already.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cb7fb4d342 ("thermal: qcom_spmi: allow compile test")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Probe error operation and remove operation are same.
Let's use same function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some systems register thermal zone by themself and don't need to
have thermal zones node in DT. Therefore reduce the log level from
ERROR to DEBUG when thermal zone node can't be find in
of_thermal_destroy_zones().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All thermal governors use the temperature value stored in
struct thermal_zone_device.
thermal_zone_device->temperature
power_allocator governor should not deviate from this and use
the same.
Cc: Javi Merino <javi.merino@arm.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Reported-by: Sugumar Natarajan <sugumar.natarajan@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3368 SoCs support to 2 channel TS-ADC, the temperature criteria
of each channel can be configurable.
The system has two Temperature Sensors, channel 0 is for CPU,
and channel 1 is for GPU.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As Temperature is currently represented as int not long in the thermal
framework since use int intead of unsigned long/long to represent
temperature to avoid bogus overheat detection when negative temperature
reported.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The conversion table has the adc value and temperature.
In fact, the adc value only has the increment or decrement mode in
conversion table.
Moment, we can add the sort mode to be better support the *code_to_temp*
for differenr SoCs.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We should make the conversion table in as a parameter since the different
SoCs have the different conversionion table.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The current driver is default to register the two thermal sensors
in probe since some SoCs maybe only have one sensor for thermal.
In some cases, the channel 0 is not always the cpu or gpu sensor.
So add the channel can be configured for sensors.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Missing a include file caused compile error.
drivers/thermal/rockchip_thermal.c: In function 'rockchip_thermal_suspend':
drivers/thermal/rockchip_thermal.c:720:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
...
Fixes: 7e38a5b1da ("thermal: rockchip: support the sleep pinctrl state
to avoid glitches")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal updates from Zhang Rui:
- Implement generic devfreq cooling mechanism through frequency
reduction for devices using devfreq. From Ørjan Eide and Javi
Merino.
- Introduce OMAP3 support on TI SoC thermal driver. From Pavel Mack
and Eduardo Valentin.
- A bounch of small fixes on devfreq_cooling, Exynos, IMX, Armada, and
Rockchip thermal drivers.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
thermal: exynos: Directly return 0 instead of using local ret variable
thermal: exynos: Remove unneeded semicolon
thermal: exynos: Use IS_ERR() because regulator cannot be NULL
thermal: exynos: Fix first temperature read after registering sensor
thermal: exynos: Fix unbalanced regulator disable on probe failure
devfreq_cooling: return on allocation failure
thermal: rockchip: support the sleep pinctrl state to avoid glitches in s2r
dt-bindings: rockchip-thermal: Add the pinctrl states in this document
thermal: devfreq_cooling: Make power a u64
thermal: devfreq_cooling: use a thermal_cooling_device for register and unregister
thermal: underflow bug in imx_set_trip_temp()
thermal: armada: Fix possible overflow in the Armada 380 thermal sensor formula
thermal: imx: register irq handler later in probe
thermal: rockhip: fix setting thermal shutdown polarity
thermal: rockchip: fix handling of invalid readings
devfreq_cooling: add trace information
thermal: Add devfreq cooling
PM / OPP: get the voltage for all OPPs
tools/thermal: tmon: use pkg-config also for CFLAGS
linux/thermal.h: rename KELVIN_TO_CELSIUS to DECI_KELVIN_TO_CELSIUS
...
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'ret' variable in exynos5440_tmu_initialize() is initialized to 0
and returned as is. Replace it with direct return statement. This also
fixes coccinelle warning:
drivers/thermal/samsung/exynos_tmu.c:611:5-8: Unneeded variable: "ret". Return "0" on line 654
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The NULL check in probe's error path is not needed because in that time
the regulator cannot be NULL (regulator_get() returns valid pointer or
ERR_PTR).
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal core could not read the temperature after registering the
thermal sensor with thermal_zone_of_sensor_register() because the driver
was not yet initialized.
The call trace looked like:
exynos_tmu_probe()
thermal_zone_of_sensor_register()
of_thermal_set_mode()
thermal_zone_device_update()
exynos_get_temp()
if (!data->tmu_read) return -EINVAL;
exynos_map_dt_data()
data->tmu_read = ...
This produced an error in dmesg:
thermal thermal_zone0: failed to read out thermal zone (-22)
Register the thermal_zone_device later, after parsing Device Tree and
enabling necessary clocks, but before calling exynos_tmu_initialize()
which uses the registered thermal_zone_device.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 3b6a1a805f ("thermal: samsung: core: Exynos TMU rework to use device tree for configuration")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe if the regulator could not be enabled, the error exit path
would still disable it. This could lead to unbalanced counter of
regulator enable/disable.
The patch moves code for getting and enabling the regulator from
exynos_map_dt_data() to probe function because it is really not a part
of getting Device Tree properties.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 5f09a5cbd1 ("thermal: exynos: Disable the regulator on probe failure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If the allocation fails then we can't continue.
Fixes: a76caf55e5 ('thermal: Add devfreq cooling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When we come out of system suspend state (S3) the tsadc will have been
reset and back at its default state. While reprogramming the tsadc
it's possible that we'll glitch the output and unintentionally cause
the "over temperature" GPIO to be asserted. Since the over
temperature GPIO is often hooked up to something that will cause a
reboot or shutdown in hardware, this glitch can be catastrophic on
some boards.
We'll add support for selecting the "sleep" pinctrl state at suspend
time. Boards can use this to effectively disable the tsadc at suspend
time and avoid glitches when the system is resumed.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The prototype of do_div() is:
uint32_t do_div(uint64_t *n, uint32_t base);
Make power u64 to avoid the following warning:
drivers/thermal/devfreq_cooling.c: In function 'get_dynamic_power':
drivers/thermal/devfreq_cooling.c:267:2: warning: comparison of distinct pointer types lacks a cast [enabled by default]
drivers/thermal/devfreq_cooling.c:267:2: warning: right shift count >= width of type [enabled by default]
drivers/thermal/devfreq_cooling.c:267:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Be consistent with what other cooling devices do and return a struct
thermal_cooling_device * on register. Also, for the unregister, accept
a struct thermal_cooling_device * as parameter.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We recently changed this from unsigned long to int so it introduced an
underflow bug.
Fixes: 17e8351a77 ('thermal: consistently use int for temperatures')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Update the coefficients so the calculation will not overrun the
unsigned long 32bits boundary
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Victor Axelrod <victora@marvell.com>
Reviewed-by: Neta Zur Hershkovits <neta@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The irq handler should be registered after the tempmon
module has been initialized in a known state and the
thermal_zone and cpu_cooling device have been registered
successfully. Otherwise, if the irq is triggled earlier
before thermal probe has been finished, it may lead to
'NULL' pointer kernel panic.
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When requested thermal shutdown signal polarity is low we need to make
sure that the bit representing high level of signal is reset, and not
set all other bits in that register.
Also rename TSADCV2_INT_PD_CLEAR to TSADCV2_INT_PD_CLEAR_MASK to better
reflect its nature.
Acked-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We attempted to signal invalid code by returning -EAGAIN from
rk_tsadcv2_code_to_temp(), unfortunately the return value was stuffed
directly into the temperature pointer, potentially confusing upper
layers with temperature of -EINVAL.
Let's split temperature from error/success indicator to avoid such
confusion.
Also change the way we scan the temperature table to start with the 2nd
element so that we do not need to worry that we may reference out of
bounds element while doing binary search and keep checking that we end
up with 'mid' equal to 0 (since we are looking for the temperature that
would fall into interval between the 'mid' and 'mid - 1') .
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Tracing is useful for debugging and performance tuning. Add similar
traces to what's present in the cpu cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a generic thermal cooling device for devfreq, that is similar to
cpu_cooling.
The device must use devfreq. In order to use the power extension of the
cooling device, it must have registered its OPPs using the OPP library.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Ørjan Eide <orjan.eide@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The value of emul_con was getting overwritten if the selected soc is
SOC_ARCH_EXYNOS5260. And so as a result we were reading from the wrong
register in the case of SOC_ARCH_EXYNOS5260.
Fixes: 488c7455d7 ("thermal: exynos: Add the support for Exynos5433 TMU")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
In the function cpufreq_get_requested_power, the memory allocated
for load_cpu is live within the function only. And after the
allocation it is immediately freed with devm_kfree. There is no
need to allocate memory for load_cpu with devm function so replace
devm_kcalloc with kcalloc and devm_kfree with kfree.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
After the commit "thermal: core: Add Kconfig option to enable writable
trips", by default the trips are read only. This cause user space thermal
controllers to poll for temperature as they can't set temperature
thresholds for getting a notification via uevents. These programs use RW
trip in a zone to register thresholds. Since we need to enable the new
config introduced by above commit to allow writable trips, selecting
CONFIG_THERMAL_WRITABLE_TRIP for x86 thermal drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
During boot I get a div by zero Oops regression starting in v4.3-rc3.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add OMAP36xx support to ti-soc-thermal driver. This
chip is also unreliable. The data provided here is
based on OMAP36xx TRM:
http://www.ti.com/lit/ug/swpu177aa/swpu177aa.pdf
Signed-off-by: Eduardo Valentin <edubezva@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for OMAP3 chips to ti-soc-thermal. As requested by
TI people, it is marked unreliable and warning is printed.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Don't waste cycles in the power allocator governor's throttle function
if there are no cooling devices and exit early.
This commit doesn't change any functionality, but should provide better
performance for the odd case of a thermal zone with trip points but
without cooling devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal zones created using thermal_zone_device_create() may not have
tzp. As the governor gets its parameters from there, allocate it while
the governor is bound to the thermal zone so that it can operate in it.
In this case, tzp is freed when the thermal zone switches to another
governor.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor currently requires that the thermal zone
has at least two passive trip points. If there aren't, the governor
refuses to bind to the thermal zone.
This commit relaxes that requirement. Now the governor will bind to all
thermal zones regardless of how many trip points they have.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor currently requires that a sustainable power
is passed as part of the thermal zone's thermal zone parameters. If
that parameter is not provided, it doesn't register with the thermal
zone.
While this parameter is strongly recommended for optimal performance, it
doesn't need to be mandatory. Relax the requirement and allow the
governor to bind to thermal zones that don't provide it by estimating it
from the cooling devices' power model.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal core already has a function to get the maximum power of a
cooling device: power_actor_get_max_power(). Add a function to get the
minimum power of a cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power table is not being freed on error from cpufreq_cooling
register or when unregistering. Free it.
Fixes: c36cf07176 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
build_dyn_power_table() allocates the power table while holding
rcu_read_lock. kcalloc using GFP_KERNEL may sleep, so it can't be
called in an RCU read-side path.
Move the rcu protection to the part of the function that really needs
it: the part that handles the dev_pm_opp pointer received from
dev_pm_opp_find_freq_ceil(). In the unlikely case that there is an OPP
added to the cpu while this function is running, return -EAGAIN.
Fixes: c36cf07176 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f882: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit 17e8351a77 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit d0a12625d2
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
This fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
This has been a busy release for regmap. By far the biggest set of
changes here are those from Markus Pargmann which implement support for
block transfers in smbus devices. This required quite a bit of
refactoring but leaves us better able to handle odd restrictions that
controllers may have and with better performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV6cZyAAoJECTWi3JdVIfQM3sH/RSygzRIOoOuvro0U3qd4+nM
qLzpuZNtuAP7xNc5yJZiixz1S6PqUNl+pK/u58s6x10GWDGsWZY6E0Lg94lYmfhA
26jqWSzrMHp42x+ZN7btLExzPTVnvRerrjtj4mqz6t4yun9SzqVymaZTUZ1hqPHB
qxSNHs3rHPiqiEWpQKJXb+5dazYYJCbOUrlivxJCk60+ns1N88cA71aY+5/zq5uy
36e0iYe3s+lv0lptedarFCf9p7o1E6EQzhvEMfyquGXtvq8fl7Qdeo7riRFQ8Iiy
sygCb3AYuZIiqnOC7+90xkr2Oq0iwdJUD91A9sl/SRiwgItG9jW03bWNHYIhQyk=
=CbGt
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap.
By far the biggest set of changes here are those from Markus Pargmann
which implement support for block transfers in smbus devices. This
required quite a bit of refactoring but leaves us better able to
handle odd restrictions that controllers may have and with better
performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald"
* tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (25 commits)
regmap: fix a NULL pointer dereference in __regmap_init
regmap: Support bulk reads for devices without raw formatting
regmap-i2c: Add smbus i2c block support
regmap: Add raw_write/read checks for max_raw_write/read sizes
regmap: regmap max_raw_read/write getter functions
regmap: Introduce max_raw_read/write for regmap_bulk_read/write
regmap: Add missing comments about struct regmap_bus
regmap: No multi_write support if bus->write does not exist
regmap: Split use_single_rw internally into use_single_read/write
regmap: Fix regmap_bulk_write for bus writes
regmap: regmap_raw_read return error on !bus->read
regulator: core: Print at debug level on debugfs creation failure
regmap: Fix regmap_can_raw_write check
regmap: fix typos in regmap.c
regmap: Fix integertypes for register address and value
regmap: Move documentation to regmap.h
regmap: Use different lockdep class for each regmap init call
thermal: sti: Add parentheses around bridge->ops->regmap_init call
mfd: vexpress: Add parentheses around bridge->ops->regmap_init call
regmap: debugfs: Fix misuse of IS_ENABLED
...
Pull x86 asm changes from Ingo Molnar:
"The biggest changes in this cycle were:
- Revamp, simplify (and in some cases fix) Time Stamp Counter (TSC)
primitives. (Andy Lutomirski)
- Add new, comprehensible entry and exit handlers written in C.
(Andy Lutomirski)
- vm86 mode cleanups and fixes. (Brian Gerst)
- 32-bit compat code cleanups. (Brian Gerst)
The amount of simplification in low level assembly code is already
palpable:
arch/x86/entry/entry_32.S | 130 +----
arch/x86/entry/entry_64.S | 197 ++-----
but more simplifications are planned.
There's also the usual laudry mix of low level changes - see the
changelog for details"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (83 commits)
x86/asm: Drop repeated macro of X86_EFLAGS_AC definition
x86/asm/msr: Make wrmsrl() a function
x86/asm/delay: Introduce an MWAITX-based delay with a configurable timer
x86/asm: Add MONITORX/MWAITX instruction support
x86/traps: Weaken context tracking entry assertions
x86/asm/tsc: Add rdtscll() merge helper
selftests/x86: Add syscall_nt selftest
selftests/x86: Disable sigreturn_64
x86/vdso: Emit a GNU hash
x86/entry: Remove do_notify_resume(), syscall_trace_leave(), and their TIF masks
x86/entry/32: Migrate to C exit path
x86/entry/32: Remove 32-bit syscall audit optimizations
x86/vm86: Rename vm86->v86flags and v86mask
x86/vm86: Rename vm86->vm86_info to user_vm86
x86/vm86: Clean up vm86.h includes
x86/vm86: Move the vm86 IRQ definitions to vm86.h
x86/vm86: Use the normal pt_regs area for vm86
x86/vm86: Eliminate 'struct kernel_vm86_struct'
x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'
x86/vm86: Move vm86 fields out of 'thread_struct'
...
Commit cf736ea6f9 ("thermal: power_allocator: do not use devm*
interfaces") forgot to change a devm_kcalloc() to just kcalloc(), but
it's corresponding devm_kfree() was changed to kfree(). Allocate with
kcalloc() to match the kfree().
Fixes: cf736ea6f9 ("thermal: power_allocator: do not use devm* interfaces")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
policy->max is the maximum allowed frequency defined by user and
clipped_freq is the maximum that thermal constraints allow.
If clipped_freq is lower than policy->max, then we need to readjust
policy->max.
But, if clipped_freq is greater than policy->max, we don't need to do
anything. We used to call cpufreq_verify_within_limits() in this case,
but it doesn't change anything in this case.
Lets skip this unnecessary call and write a comment that explains this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
That's what it is for, lets name it properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
That's what it is for, lets name it properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We just need to take care of single event here and there is no need to
increase indentation level of most of the code (which causes lines
longer that 80 columns to break).
Kill the switch block.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If a valid cpufreq_dev is found for policy->cpu, we should update the
policy and quit the for loop. There is no need to keep traversing the
list of cpufreq_dev's.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Its always set before getting used, don't initialize it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The code in question is called outside of standard driver
probe()/remove() callbacks and thus will not benefit from use of devm*
infrastructure.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
regmap_init(...) is a macro since commit
"regmap: Use different lockdep class for each regmap init call".
That same name is used as a function pointer: prevent its expansion
by adding parentheses around the function pointer.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds a thermal driver for Wildcat Point platform controller
hub. This driver register PCH thermal sensor as a thermal zone and
associate critical and hot trips if present.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The code testing if a temperature should be emulated or not is
not obvious. Add a comment explaining why this test is done.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use IS_ENABLED(CONFIG_THERMAL_EMULATION) to make the code more readable
and to get rid of the addtional #ifdef around the variable definitions
in thermal_zone_get_temp().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When the thermal zone has no get_temp callback then thermal_zone_device_register()
calls thermal_zone_device_set_polling() with a polling delay of 0. This
only cancels the poll_queue. Since the poll_queue hasn't been scheduled this
is a no-op. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Linux thermal framework support to change thermal governor
policy in userspace, but it can't show what available policies
supported.
This patch adds available_policies attribute to the thermal
framework, it can list the thermal governors which can be
used for a particular zone. This attribute is read only.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add support for Intel Denlow UP server platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The exynos thermal driver use the of_thermal_*() API to parse the basic data
for thermal management from devicetree file. So, if CONFIG_EXYNOS_THERMAL is
selected without CONFIG_THERMAL_OF, kernel can build it without any problem.
But, exynos thermal driver is not working with following error log. This patch
add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF.
[ 1.458644] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.459096] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.465211] exynos4412_tmu_initialize: No CRITICAL trip point defined at of-thermal.c!
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe the regulator (if present) was enabled but not disabled in
case of failure. So an unsuccessful probe lead to enabling the
regulator which was actually not needed because the device was not
enabled.
Additionally each deferred probe lead to increase of regulator enable
count so it would not be effectively disabled during removal of the
device.
Test HW: Exynos4412 - Trats2 board
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 498d22f616 ("thermal: exynos: Support for TMU regulator defined at device tree")
Cc: <stable@vger.kernel.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor uses ftrace to output a bunch of internal
data for debugging and tuning. Currently, the requested power it
outputs is the "weighted" requested power, that is, what each cooling
device has requested multiplied by the cooling device weight. It is
more useful to trace the real request, without any weight being
applied.
This commit only affects the data traced, there is no functional change.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull thermal management updates from Zhang Rui:
"Specifics:
- enhance Thermal Framework with several new capabilities:
* use power estimates
* compute weights with relative integers instead of percentages
* allow governors to have private data in thermal zones
* export thermal zone parameters through sysfs
Thanks to the ARM thermal team (Javi, Punit, KP).
- introduce a new thermal governor: power allocator. First in kernel
closed loop PI(D) controller for thermal control. Thanks to ARM
thermal team.
- enhance OF thermal to allow thermal zones to have sustainable power
HW specification. Thanks to Punit.
- introduce thermal driver for Intel Quark SoC x1000platform. Thanks
to Ong, Boon Leong.
- introduce QPNP PMIC temperature alarm driver. Thanks to Ivan T. I.
- introduce thermal driver for Hisilicon hi6220. Thanks to
kongxinwei.
- enhance Exynos thermal driver to handle Exynos5433 TMU. Thanks to
Chanwoo C.
- TI thermal driver now has a better implementation for EOCZ bit.
From Pavel M.
- add id for Skylake processors in int340x processor thermal driver.
- a couple of small fixes and cleanups."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: hisilicon: add new hisilicon thermal sensor driver
dt-bindings: Document the hi6220 thermal sensor bindings
thermal: of-thermal: add support for reading coefficients property
thermal: support slope and offset coefficients
thermal: power_allocator: round the division when divvying up power
thermal: exynos: Add the support for Exynos5433 TMU
thermal: cpu_cooling: Fix power calculation when CPUs are offline
thermal: cpu_cooling: Remove cpu_dev update on policy CPU update
thermal: export thermal_zone_parameters to sysfs
thermal: cpu_cooling: Check memory allocation of power_table
ti-soc-thermal: request temperature periodically if hw can't do that itself
ti-soc-thermal: implement eocz bit to make driver useful on omap3
cleanup ti-soc-thermal
thermal: remove stale THERMAL_POWER_ACTOR select
thermal: Default OF created trip points to writable
thermal: core: Add Kconfig option to enable writable trips
thermal: x86_pkg_temp: drop const for thermal_zone_parameters
of: thermal: Introduce sustainable power for a thermal zone
thermal: add trace events to the power allocator governor
thermal: introduce the Power Allocator governor
...
This patch adds the support for hisilicon thermal sensor, within
hisilicon SoC. there will register sensors for thermal framework
and use device tree to bind cooling device.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: kongxinwei <kong.kongxinwei@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In order to avoid having each driver adding their own
specific DT property to specify slope and offset,
this patch adds a basic coefficient reading from
DT thermal zone node. Right now, as the thermal
framework does not support multiple sensors,
the current coefficients apply only to the only
sensor in the thermal zone.
The supported equation is a simple linear model:
slope * <sensor reading> + offset.
slope and offset are read from the coefficients
DT property. In the same way as it is described in
the DT thermal binding.
So, as of today, the thermal framework will support
only cases like:
/* hotspot = 1 * adc + 6000 */
coefficients = <1 6000>;
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It is common to have a linear extrapolation from
the current sensor readings and the actual temperature
value. This is specially the case when the sensor
is in use to extrapolate hotspots.
This patch adds slope and offset constants for
single sensor linear extrapolation equation. Because
the same sensor can be use in different locations,
from board to board, these constants are added
as part of thermal_zone_params.
The constants are available through sysfs.
It is up to the device driver to determine
the usage of these values.
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In situations where there is an uneven number of cooling devices, the
division of power among them can lead to a milliwatt being dropped on
the floor due to rounding errors. This doesn't sound like a lot, but
some devices only grant the lowest cooling device state for their
maximum power. So for instance, if the granted_power is the maximum
power and all devices are getting their maximum power, one would get
max_power - 1, making it choose cooling device state 1, instead of 0.
Round the division to make the calculation more accurate.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is a copy and paste bug, "->clk" vs "->pclk", so we return the
wrong error code here.
Fixes: cbac8f6394 ('thermal: rockchip: add driver for thermal')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Package C8 to C10 was introduced in newer Intel CPUs, we need to
include them in the package c-state residency calculation.
Otherwise, idle injection target is not accurately maintained by
the closed control loop.
Also cleaned up the code to make it scale better with large number
of c-states.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Broadwell server has support for package C-states, idle injection works
as expected on this platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mark the module init / exit functions with __init / __exit accodingly.
This allows making the intel_powerclamp_ids[] array __initconst, too, as
it only gets referenced from powerclamp_probe(). This is safe as
file2alias doesn't care about the section, but the symbol name for the
MODULE_DEVICE_TABLE alias.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
DESCRIPTION
Spurious Thermal Alert: Talert can happen randomly while the device remains
under the temperature limit defined for this event to trig. This spurious
event is caused by a incorrect re-synchronization between clock domains.
The comparison between configured threshold and current temperature value
can happen while the value is transitioning (metastable), thus causing
inappropriate event generation. No spurious event occurs as long as the
threshold value stays unchanged. Spurious event can be generated while a
thermal alert threshold is modified in
CONTROL_BANDGAP_THRESHOLD_MPU/GPU/CORE/DSPEVE/IVA_n.
WORKAROUND
Spurious event generation can be avoided by performing following sequence
when the threshold is modified:
1. Mask the hot/cold events at the thermal IP level.
2. Modify Threshold.
3. Unmask the hot/cold events at the thermal IP level.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Bandgap Temperature read Dtemp can be corrupted
DESCRIPTION
Read accesses to registers listed below can be corrupted due to
incorrect resynchronization between clock domains.
Read access to registers below can be corrupted :
• CTRL_CORE_DTEMP_MPU/GPU/CORE/DSPEVE/IVA_n (n = 0 to 4)
• CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA_n
WORKAROUND
Multiple reads to CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA[9:0]:
BGAP_DTEMPMPU/GPU/CORE/DSPEVE/IVA is needed to discard false value and
read right value:
1. Perform two successive reads to BGAP_DTEMP bit field.
(a) If read1 returns Val1 and read2 returns Val1, then
right value is Val1.
(b) If read1 returns Val1, read 2 returns Val2, a third
read is needed.
2. Perform third read
(a) If read3 returns Val2 then right value is Val2.
(b) If read3 returns Val3, then right value is Val3.
The above in gist means if val1 and val2 are the same then we can go
ahead with that value else we need a third read which will be right
since synchronization will be complete by then.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds the support for Exynos5433's TMU (Thermal Management Unit).
Exynos5433 has a little different register bit fields as following description:
- Support the eight trip points for rising/falling interrupt by using two registers
- Read the calibration type (1-point or 2-point) and sensor id from TRIMINFO register
- Use a little different register address
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Ensure that the CPU for which the frequency is being requested
is online. If none of the CPUs are online the requested power is
returned as 0.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It was initially understood that an update to the cpu_device
(cached in cpufreq_cooling_device) was required to ascertain the
correct operating point of the device on a cpufreq policy->cpu update
or creation or deletion of a cpufreq policy.
(e.g. when the existing policy CPU goes offline).
This update is not required and it is possible to ascertain the OPPs
from the leading CPU in a cpufreq domain even if the CPU is hotplugged out.
Fixes: e0128d8ab423 ("thermal: cpu_cooling: implement the power cooling device API")
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It's useful for tuning to be able to edit thermal_zone_parameters from
userspace. Export them to the thermal_zone sysfs so that they can be
easily changed.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We allocate the power_table in memory but we don't test whether the
allocation succeeded. Return -ENOMEM if kcalloc() fails.
Fixes: e0128d8ab423 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When periodic mode is not enabled, it is neccessary to force reads.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For omap3, proper implementation of eocz bit is needed. It was
actually a TODO in the driver.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Simplify code by removing goto's where they point to simple return.
Avoid confusing |= on error values.
Correct whitespace.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
A previous version of this patch had a config for THERMAL_POWER_ACTOR
but it was dropped. Remove the select as it is not doing anything.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When registering a thermal zone from device tree, default the trip
points to writable. By default, only the root user can change these.
This allows the trip points to be tweaked after the system has
booted.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a Kconfig option to allow system integrators to control whether
userspace tools can change trip temperatures. This option overrides
the thermal zone setup in the driver code and must be enabled for
platform specified writable trips to come into effect.
The original behaviour of requiring root privileges to change trip
temperatures remains unchanged.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
8754d5115693 ("thermal: introduce the Power Allocator governor") dropped
the const attribute in the struct thermal_zone_device. That means that
the thermal_zone_params pointer passed to thermal_zone_device_register()
also lost the const qualifier. Drop the const in x86_pkg_temp_thermal.c
as well to avoid the following warning as reported by the kbuild test
robot:
drivers/thermal/x86_pkg_temp_thermal.c: In function 'pkg_temp_thermal_device_add':
>> drivers/thermal/x86_pkg_temp_thermal.c:450:31: warning: passing argument 6 of 'thermal_zone_device_register' discards 'const' qualifier from pointer target type
phy_dev_entry, &tzone_ops, &pkg_temp_tz_params, 0, 0);
^
In file included from drivers/thermal/x86_pkg_temp_thermal.c:30:0:
include/linux/thermal.h:378:29: note: expected 'struct thermal_zone_params *' but argument is of type 'const struct thermal_zone_params *'
struct thermal_zone_device *thermal_zone_device_register(const char *, int, int,
^
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Introduce an optional property called, sustainable-power, which
represents the power (in mW) which the thermal zone can safely
dissipate.
If provided the property is parsed and associated with the thermal
zone via the thermal zone parameters.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add trace events for the power allocator governor and the power actor
interface of the cpu cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor is a thermal governor that controls system
and device power allocation to control temperature. Conceptually, the
implementation divides the sustainable power of a thermal zone among
all the heat sources in that zone.
This governor relies on "power actors", entities that represent heat
sources. They can report current and maximum power consumption and
can set a given maximum power consumption, usually via a cooling
device.
The governor uses a Proportional Integral Derivative (PID) controller
driven by the temperature of the thermal zone. The output of the
controller is a power budget that is then allocated to each power
actor that can have bearing on the temperature we are trying to
control. It decides how much power to give each cooling device based
on the performance they are requesting. The PID controller ensures
that the total power budget does not exceed the control temperature.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a basic power model to the cpu cooling device to implement the
power cooling device API. The power model uses the current frequency,
current load and OPPs for the power calculations. The cpus must have
registered their OPPs using the OPP library.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add three optional callbacks to the cooling device interface to allow
them to express power. In addition to the callbacks, add helpers to
identify cooling devices that implement the power cooling device API.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
A governor may need to store its current state between calls to
throttle(). That state depends on the thermal zone, so store it as
private data in struct thermal_zone_device.
The governors may have two new ops: bind_to_tz() and unbind_from_tz().
When provided, these functions let governors do some initialization
and teardown when they are bound/unbound to a tz and possibly store that
information in the governor_data field of the struct
thermal_zone_device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for the temperature alarm peripheral found inside
Qualcomm plug-and-play (QPNP) PMIC chips. The temperature alarm
peripheral outputs a pulse on an interrupt line whenever the
thermal over temperature stage value changes.
Register a thermal sensor. The temperature reported by this thermal
sensor device should reflect the actual PMIC die temperature if an
ADC is present on the given PMIC. If no ADC is present, then the
reported temperature should be estimated from the over temperature
stage value.
Cc: David Collins <collinsd@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fair share governor has the concept of weights, which is the
influence of each cooling device in a thermal zone. The current
implementation forces the weights of all cooling devices in a thermal
zone to add up to a 100. This complicates setups, as you need to know
in advance how many cooling devices you are going to have. If you bind a
new cooling device, you have to modify all the other cooling devices
weights, which is error prone. Furthermore, you can't specify a
"default" weight for platforms since that default value depends on the
number of cooling devices in the platform.
This patch generalizes the concept of weight by allowing any number to
be a "weight". Weights are now relative to each other. Platforms that
don't specify weights get the same default value for all their cooling
devices, so all their cdevs are considered to be equally influential.
It's important to note that previous users of the weights don't need to
alter the code: percentages continue to work as they used to. This
patch just removes the constraint of all the weights in a thermal zone
having to add up to a 100. If they do, you get the same behavior as
before. If they don't, fair share now works for that platform.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It's useful to have access to the weights for the cooling devices for
thermal zones and change them if needed. Export them to sysfs.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fair share governor is not usable with thermal zones that use the
bind op and don't populate thermal_zone_parameters, the majority of
them. Now that the weight is in the thermal instance, we can use that
in the fair share governor to allow every thermal zone to trivially use
this governor. Furthermore, this simplifies the code.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently you can specify the weight of the cooling device in the device
tree but that information is not populated to the
thermal_bind_params where the fair share governor expects it to
be. The of thermal zone device doesn't have a thermal_bind_params
structure and arguably it's better to pass the weight inside the
thermal_instance as it is specific to the bind of a cooling device to a
thermal zone parameter.
Core thermal code is fixed to populate the weight in the instance from
the thermal_bind_params, so platform code that was passing the weight
inside the thermal_bind_params continue to work seamlessly.
While we are at it, create a default value for the weight parameter for
those thermal zones that currently don't define it and remove the
hardcoded default in of-thermal.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch enables intel_powerclamp driver to run on the
next-generation Intel(R) Xeon Phi Microarchitecture
code named "Knights Landing"
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
drivers/thermal/intel_soc_dts_iosf.c:358:4-7: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS).
The DTS offers both hot & critical trip points.
However, in current distribution of UEFI BIOS for Quark platform, only
critical trip point is configured to be 105 degree Celsius (based on Quark
SW ver1.0.1 and hot trip point is not used due to lack of IRQ.
There is no active cooling device for Quark SoC, so Quark SoC thermal
management logic expects Linux distro to orderly power-off when temperature
of the DTS exceeds the configured critical trip point.
Kernel param "polling_delay" in milliseconds is used to control the frequency
the DTS temperature is read by thermal framework. It defaults to 2-second.
To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X".
User interacts with Quark SoC DTS thermal driver through sysfs via:
/sys/class/thermal/thermal_zone0/
For example:
- to read DTS temperature
$ cat temp
- to read critical trip point
$ cat trip_point_0_temp
- to read trip point type
$ cat trip_point_0_type
- to emulate temperature raise to test orderly shutdown by Linux distro
$ echo 105 > emul_temp
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Support two auxiliary DTS present on Braswell platform using side band
IOSF interface. This supports two read write trips, which can be used
to get notification on trip violation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
There is no change in functionality but using the common IOSF core APIs.
This driver is now just responsible for enumeration and call relevant
API to create thermal zone and register critical trip.
Also cpuid 0x4c is now handled in the int340x processor thermal driver
with the same functionality.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This is becoming a common feature for Intel SoCs to expose the additional
digital temperature sensors (DTSs) using side band interface (IOSF). This
change remove common IOSF DTS handler function from the existing driver
intel_soc_dts_thermal.c and creates a stand alone module, which can
be selected from the SoC specific drivers. In this way there is less
code duplication.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Default attributes are created when the device is registered. Attributes
created after device registration can lead to race conditions, where user space
(e.g. udev) sees the device but not the attributes.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When thermal zone device register fails or on module exit, the memory
for aux_trip is not freed. This change fixes this issue.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the wrong control of PD_DET_EN (power down detection mode)
for Exynos7 because exynos7_tmu_control() always enables the power down detection
mode regardless 'on' parameter.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
It is possible that _ART/_TRT tables are missing or have errors.
Ignore those failures, as INT3400 thermal zone is still required
for _OSC or mode switch.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable Intel Powerclamp driver on Atom* Processor C2000 Product
Family for Microservers (Avoton). Avoton - SoCs for micro-servers
has package C-states which can be used for idle injection.
Reported-by: Jose Navarro <jose.navarro@intel.com>
Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Jose Carlos Venegas Munoz <jos.c.venegas.munoz@intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Swap interrupt disable and thermal zone unregistration in the error and
remove paths, to make them more symmetrical with the initialization
path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As soon as the interrupt has been enabled by devm_request_irq(), the
interrupt routine may be called, depending on the current status of the
hardware.
However, at that point rcar_thermal_common hasn't been initialized
complely yet. E.g. rcar_thermal_common.base is still NULL, causing a
NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0004000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc7-ape6evm-04564-gb6e46cb7cbe82389 #30
Hardware name: Generic R8A73A4 (Flattened Device Tree)
task: ee8953c0 ti: ee896000 task.ti: ee896000
PC is at rcar_thermal_irq+0x1c/0xf0
LR is at _raw_spin_lock_irqsave+0x48/0x54
Postpone the call to devm_request_irq() until all initialization has
been done to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cpufreq_cooling_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fix following build warning if CONFIG_PM_SLEEP is not set:
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1478:12: warning: 'ti_bandgap_suspend' defined but not used [-Wunused-function]
static int ti_bandgap_suspend(struct device *dev)
^
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1492:12: warning: 'ti_bandgap_resume' defined but not used [-Wunused-function]
static int ti_bandgap_resume(struct device *dev)
^
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The exynos_tmu_data() function should on entrance test not only for valid
data pointer, but also for data->tmu_read one.
It is important, since afterwards it is dereferenced to get temperature code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
Pull thermal managament updates from Zhang Rui:
"Specifics:
- Abstract the code and introduce helper functions for all int340x
thermal drivers. From: Srinivas Pandruvada.
- Reorganize the ACPI LPAT table support code so that it can be
shared for both ACPI PMIC driver and int340x thermal driver.
- Add support for Braswell in intel_soc_dts thermal driver.
- a couple of small fixes/cleanups for step_wise governor and int340x
thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal/int340x_thermal: remove unused uuids.
thermal: step_wise: spelling fixes
thermal: int340x: fix sparse warning
Thermal/int340x: LPAT conversion for temperature
ACPI / PMIC: Use common LPAT table handling functions
ACPI / LPAT: Common table processing functions
thermal: Intel SoC DTS: Add Braswell support
Thermal/int340x/int3402: Provide notification support
Thermal/int340x/processor_thermal: Add thermal zone support
Thermal/int340x/int3403: Use int340x thermal API
Thermal/int340x/int3402: Use int340x thermal API
Thermal/int340x: Add common thermal zone handler
this patch fixes following sparse warning:
processor_thermal_device.c:188:6: warning: symbol 'proc_thermal_remove' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add registers, bit fields and compatible strings for Exynos7 TMU
(Thermal Management Unit). Following are a few of the differences
in the Exynos7 TMU from earlier SoCs:
- 8 trigger levels
- Different bit offsets and more registers for the rising
and falling thresholds.
- New power down detection bit in the TMU_CONTROL register
which does not update the CURRENT_TEMP0 when tmu power down
is detected.
- Change in bit offset for the NEXT_DATA field of EMUL_CON
register. EMUL_CON register address has also changed.
- INTSTAT and INTCLEAR registers present in earlier SoCs
have been combined into one INTPEND register. The register
address for INTCLEAR and INTPEND is also different.
- Since there are 8 rising/falling interrupts as against
at most 4 in earlier SoCs the INTEN bit offsets are different.
- Multiple probe support which is handled by a TMU_CONTROL1
register (No support for this in the current patch).
This patch adds special clock support required only for Exynos7. It
also updates the "code_to_temp" prototype as Exynos7 has 9 bit
code-temp mapping.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When LPAT table is present, we need to convert raw temperature to
real temp using LPAT.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added Intel Braswell CPU id for SOC DTS. Since this doesn't support
APIC IRQ, the driver is modified to have capability to not register
any modifiable trips.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Up till now, by mistake, wrong variable was tested against being NULL.
Since exynos_report_trigger() is always called with valid p pointer,
it is only necessary to check if a valid thermal zone device is passed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Wei Ni