Add S500 variant to the list of devices supported by the Actions Semi
Owl I2C driver.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Speed up the boot process by using the asynchronous probing feature
supported by the recent kernels.
For SBCs based on the Actions Semi S500 SoC, the overall boot time is
expected to be reduced by 200-300 ms.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Atomic transfers are required to properly power off a machine through
an I2C controlled PMIC, such as the Actions Semi ATC260x series.
System shutdown may happen with interrupts being disabled and, as a
consequence, the kernel may hang if the driver does not support atomic
transfers.
This functionality is essentially implemented by polling the FIFO
Status register until either Command Execute Completed or NACK Error
bits are set.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[wsa: rebased to current tree]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af4 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
it will print an error message by itself when platform_get_irq()
goes wrong. so don't need dev_err() in here again.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add S700 to the list of devices supported by Owl I2C driver.
Add Actions Semiconductor Owl family S700 I2C driver.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cristian Ciocaltea