Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/net/ethernet/wiznet/w5100.c:758:12: warning: 'w5100_suspend' defined but not used [-Wunused-function]
drivers/net/ethernet/wiznet/w5100.c:773:12: warning: 'w5100_resume' defined but not used [-Wunused-function]
drivers/net/ethernet/wiznet/w5300.c:670:12: warning: 'w5300_suspend' defined but not used [-Wunused-function]
drivers/net/ethernet/wiznet/w5300.c:685:12: warning: 'w5300_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.
With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using eth_hw_addr_random() to generate a random Ethernet address
(MAC) to be used by a net device and set addr_assign_type.
Not need to duplicating its implementation.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes possible null dereference in probe() function: when both
.mac_addr and .link_gpio are unknown, dev.platform_data may be NULL
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
m68k/allmodconfig:
drivers/net/ethernet/wiznet/w5100.c: In function ‘w5100_hw_probe’:
drivers/net/ethernet/wiznet/w5100.c:680: error: ‘IRQ_TYPE_LEVEL_LOW’ undeclared (first use in this function)
drivers/net/ethernet/wiznet/w5300.c: In function ‘w5300_hw_probe’:
drivers/net/ethernet/wiznet/w5300.c:594: error: ‘IRQ_TYPE_LEVEL_LOW’ undeclared (first use in this function)
Include <linux/irq.h>, which provides the declaration for IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option was there for debugging race conditions,
just remove it, and assume TX_FLOW is always enabled.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han