[ Upstream commit d0304569fb019d1bcfbbbce1ce6df6b96f04079b ]
Kernel timekeeping is designed to keep the change in cycles (since the last
timer interrupt) below max_cycles, which prevents multiplication overflow
when converting cycles to nanoseconds. However, if timer interrupts stop,
the clocksource_cyc2ns() calculation will eventually overflow.
Add protection against that. Simplify by folding together
clocksource_delta() and clocksource_cyc2ns() into cycles_to_nsec_safe().
Check against max_cycles, falling back to a slower higher precision
calculation.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240325064023.2997-20-adrian.hunter@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2655ac2c06a15558e51ed6529de280e1553c86e ]
The current "nretries > 1 || nretries >= max_retries" check in
cs_watchdog_read() will always evaluate to true, and thus pr_warn(), if
nretries is greater than 1. The intent is instead to never warn on the
first try, but otherwise warn if the successful retry was the last retry.
Therefore, change that "||" to "&&".
Fixes: db3a34e174 ("clocksource: Retry clock read if long delays detected")
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240802154618.4149953-2-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ed08e4bc53298db3f87b528cd804cb0cce066a9 ]
On a 8-socket server the TSC is wrongly marked as 'unstable' and disabled
during boot time on about one out of 120 boot attempts:
clocksource: timekeeping watchdog on CPU227: wd-tsc-wd excessive read-back delay of 153560ns vs. limit of 125000ns,
wd-wd read-back delay only 11440ns, attempt 3, marking tsc unstable
tsc: Marking TSC unstable due to clocksource watchdog
TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
sched_clock: Marking unstable (119294969739, 159204297)<-(125446229205, -5992055152)
clocksource: Checking clocksource tsc synchronization from CPU 319 to CPUs 0,99,136,180,210,542,601,896.
clocksource: Switched to clocksource hpet
The reason is that for platform with a large number of CPUs, there are
sporadic big or huge read latencies while reading the watchog/clocksource
during boot or when system is under stress work load, and the frequency and
maximum value of the latency goes up with the number of online CPUs.
The cCurrent code already has logic to detect and filter such high latency
case by reading the watchdog twice and checking the two deltas. Due to the
randomness of the latency, there is a low probabilty that the first delta
(latency) is big, but the second delta is small and looks valid. The
watchdog code retries the readouts by default twice, which is not
necessarily sufficient for systems with a large number of CPUs.
There is a command line parameter 'max_cswd_read_retries' which allows to
increase the number of retries, but that's not user friendly as it needs to
be tweaked per system. As the number of required retries is proportional to
the number of online CPUs, this parameter can be calculated at runtime.
Scale and enlarge the number of retries according to the number of online
CPUs and remove the command line parameter completely.
[ tglx: Massaged change log and comments ]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jin Wang <jin1.wang@intel.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240221060859.1027450-1-feng.tang@intel.com
Stable-dep-of: f2655ac2c06a ("clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 644649553508b9bacf0fc7a5bdc4f9e0165576a5 upstream.
There have been reports of the watchdog marking clocksources unstable on
machines with 8 NUMA nodes:
clocksource: timekeeping watchdog on CPU373:
Marking clocksource 'tsc' as unstable because the skew is too large:
clocksource: 'hpet' wd_nsec: 14523447520
clocksource: 'tsc' cs_nsec: 14524115132
The measured clocksource skew - the absolute difference between cs_nsec
and wd_nsec - was 668 microseconds:
cs_nsec - wd_nsec = 14524115132 - 14523447520 = 667612
The kernel used 200 microseconds for the uncertainty_margin of both the
clocksource and watchdog, resulting in a threshold of 400 microseconds (the
md variable). Both the cs_nsec and the wd_nsec value indicate that the
readout interval was circa 14.5 seconds. The observed behaviour is that
watchdog checks failed for large readout intervals on 8 NUMA node
machines. This indicates that the size of the skew was directly proportinal
to the length of the readout interval on those machines. The measured
clocksource skew, 668 microseconds, was evaluated against a threshold (the
md variable) that is suited for readout intervals of roughly
WATCHDOG_INTERVAL, i.e. HZ >> 1, which is 0.5 second.
The intention of 2e27e793e2 ("clocksource: Reduce clocksource-skew
threshold") was to tighten the threshold for evaluating skew and set the
lower bound for the uncertainty_margin of clocksources to twice
WATCHDOG_MAX_SKEW. Later in c37e85c135 ("clocksource: Loosen clocksource
watchdog constraints"), the WATCHDOG_MAX_SKEW constant was increased to
125 microseconds to fit the limit of NTP, which is able to use a
clocksource that suffers from up to 500 microseconds of skew per second.
Both the TSC and the HPET use default uncertainty_margin. When the
readout interval gets stretched the default uncertainty_margin is no
longer a suitable lower bound for evaluating skew - it imposes a limit
that is far stricter than the skew with which NTP can deal.
The root causes of the skew being directly proportinal to the length of
the readout interval are:
* the inaccuracy of the shift/mult pairs of clocksources and the watchdog
* the conversion to nanoseconds is imprecise for large readout intervals
Prevent this by skipping the current watchdog check if the readout
interval exceeds 2 * WATCHDOG_INTERVAL. Considering the maximum readout
interval of 2 * WATCHDOG_INTERVAL, the current default uncertainty margin
(of the TSC and HPET) corresponds to a limit on clocksource skew of 250
ppm (microseconds of skew per second). To keep the limit imposed by NTP
(500 microseconds of skew per second) for all possible readout intervals,
the margins would have to be scaled so that the threshold value is
proportional to the length of the actual readout interval.
As for why the readout interval may get stretched: Since the watchdog is
executed in softirq context the expiration of the watchdog timer can get
severely delayed on account of a ksoftirqd thread not getting to run in a
timely manner. Surely, a system with such belated softirq execution is not
working well and the scheduling issue should be looked into but the
clocksource watchdog should be able to deal with it accordingly.
Fixes: 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold")
Suggested-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jiri Wiesner <jwiesner@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240122172350.GA740@incl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nanosecond-to-millisecond skew computation uses unsigned arithmetic,
which produces user-unfriendly large positive numbers for negative skews.
Therefore, use signed arithmetic for this computation in order to preserve
the negativity.
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Fixes: dd02926994 ("clocksource: Improve "skew is too large" messages")
Reviewed-by: Feng Tang <feng.tang@intel.com>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Bugs have been reported on 8 sockets x86 machines in which the TSC was
wrongly disabled when the system is under heavy workload.
[ 818.380354] clocksource: timekeeping watchdog on CPU336: hpet wd-wd read-back delay of 1203520ns
[ 818.436160] clocksource: wd-tsc-wd read-back delay of 181880ns, clock-skew test skipped!
[ 819.402962] clocksource: timekeeping watchdog on CPU338: hpet wd-wd read-back delay of 324000ns
[ 819.448036] clocksource: wd-tsc-wd read-back delay of 337240ns, clock-skew test skipped!
[ 819.880863] clocksource: timekeeping watchdog on CPU339: hpet read-back delay of 150280ns, attempt 3, marking unstable
[ 819.936243] tsc: Marking TSC unstable due to clocksource watchdog
[ 820.068173] TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
[ 820.092382] sched_clock: Marking unstable (818769414384, 1195404998)
[ 820.643627] clocksource: Checking clocksource tsc synchronization from CPU 267 to CPUs 0,4,25,70,126,430,557,564.
[ 821.067990] clocksource: Switched to clocksource hpet
This can be reproduced by running memory intensive 'stream' tests,
or some of the stress-ng subcases such as 'ioport'.
The reason for these issues is the when system is under heavy load, the
read latency of the clocksources can be very high. Even lightweight TSC
reads can show high latencies, and latencies are much worse for external
clocksources such as HPET or the APIC PM timer. These latencies can
result in false-positive clocksource-unstable determinations.
These issues were initially reported by a customer running on a production
system, and this problem was reproduced on several generations of Xeon
servers, especially when running the stress-ng test. These Xeon servers
were not production systems, but they did have the latest steppings
and firmware.
Given that the clocksource watchdog is a continual diagnostic check with
frequency of twice a second, there is no need to rush it when the system
is under heavy load. Therefore, when high clocksource read latencies
are detected, suspend the watchdog timer for 5 minutes.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Waiman Long <longman@redhat.com>
Cc: John Stultz <jstultz@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
When clocksource_watchdog() detects excessive clocksource skew compared
to the watchdog clocksource, it marks the clocksource under test as
unstable and prints several lines worth of message. But that message
is unclear to anyone unfamiliar with the code:
clocksource: timekeeping watchdog on CPU2: Marking clocksource 'wdtest-ktime' as unstable because the skew is too large:
clocksource: 'kvm-clock' wd_nsec: 400744390 wd_now: 612625c2c wd_last: 5fa7f7c66 mask: ffffffffffffffff
clocksource: 'wdtest-ktime' cs_nsec: 600744034 cs_now: 173081397a292d4f cs_last: 17308139565a8ced mask: ffffffffffffffff
clocksource: 'kvm-clock' (not 'wdtest-ktime') is current clocksource.
Therefore, add the following line near the end of that message:
Clocksource 'wdtest-ktime' skewed 199999644 ns (199 ms) over watchdog 'kvm-clock' interval of 400744390 ns (400 ms)
This new line clearly indicates the amount of skew between the two
clocksources, along with the duration of the time interval over which
the skew occurred, both in nanoseconds and milliseconds.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: John Stultz <jstultz@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Feng Tang <feng.tang@intel.com>
When cs_watchdog_read() is unable to get a qualifying clocksource read
within the limit set by max_cswd_read_retries, it prints a message
and marks the clocksource under test as unstable. But that message is
unclear to anyone unfamiliar with the code:
clocksource: timekeeping watchdog on CPU13: wd-tsc-wd read-back delay 1000614ns, attempt 3, marking unstable
Therefore, add some context so that the message appears as follows:
clocksource: timekeeping watchdog on CPU13: wd-tsc-wd excessive read-back delay of 1000614ns vs. limit of 125000ns, wd-wd read-back delay only 27ns, attempt 3, marking tsc unstable
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: John Stultz <jstultz@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Feng Tang <feng.tang@intel.com>
Currently, MAX_SKEW_USEC is set to 100 microseconds, which has worked
reasonably well. However, NTP is willing to tolerate 500 microseconds
of skew per second, and a clocksource that is good enough for NTP should
be good enough for the clocksource watchdog. The watchdog's skew is
controlled by MAX_SKEW_USEC and the CLOCKSOURCE_WATCHDOG_MAX_SKEW_US
Kconfig option. However, these values are doubled before being associated
with a clocksource's ->uncertainty_margin, and the ->uncertainty_margin
values of the pair of clocksource's being compared are summed before
checking against the skew.
Therefore, set both MAX_SKEW_USEC and the default for the
CLOCKSOURCE_WATCHDOG_MAX_SKEW_US Kconfig option to 125 microseconds of
skew per second, resulting in 500 microseconds of skew per second in
the clocksource watchdog's skew comparison.
Suggested-by Rik van Riel <riel@surriel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Some "TSC fall back to HPET" messages appear on systems having more than
2 NUMA nodes:
clocksource: timekeeping watchdog on CPU168: hpet read-back delay of 4296200ns, attempt 4, marking unstable
The "hpet" here is misleading the clocksource watchdog is really
doing repeated reads of "hpet" in order to check for unrelated delays.
Therefore, print the name of the clocksource under test, prefixed by
"wd-" and suffixed by "-wd", for example, "wd-tsc-wd".
Signed-off-by: Yunying Sun <yunying.sun@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:
@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)
@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@
- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);
// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@
((T)get_random_u32()@p & (LITERAL))
// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@
value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))
// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@
- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)
@collapse_ret@
type T;
identifier VAR;
expression E;
@@
{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}
@drop_var@
type T;
identifier VAR;
@@
{
- T VAR;
... when != VAR
}
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> # for drbd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
clocksource_verify_percpu() calls cpumask_weight() to check if any bit of a
given cpumask is set.
This can be done more efficiently with cpumask_empty() because
cpumask_empty() stops traversing the cpumask as soon as it finds first set
bit, while cpumask_weight() counts all bits unconditionally.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220210224933.379149-24-yury.norov@gmail.com
A watchdog maximum skew of 100us may still be too small for
some systems or archs. It may also be too small when some kernel
debug config options are enabled. So add a new Kconfig option
CLOCKSOURCE_WATCHDOG_MAX_SKEW_US to allow kernel builders to have more
control on the threshold for marking clocksource as unstable.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQHJBAABCgAzFiEEi8GdvG6xMhdgpu/4sUSA/TofvsgFAmHi+xgVHHl1cnkubm9y
b3ZAZ21haWwuY29tAAoJELFEgP06H77IxdoMAMf3E+L51Ys/4iAiyJQNVoT3aIBC
A8ZVOB9he1OA3o3wBNIRKmICHk+ovnfCWcXTr9fG/Ade2wJz88NAsGPQ1Phywb+s
iGlpySllFN72RT9ZqtJhLEzgoHHOL0CzTW07TN9GJy4gQA2h2G9CTP+OmsQdnVqE
m9Fn3PSlJ5lhzePlKfnln8rGZFgrriJakfEFPC79n/7an4+2Hvkb5rWigo7KQc4Z
9YNqYUcHWZFUgq80adxEb9LlbMXdD+Z/8fCjOrAatuwVkD4RDt6iKD0mFGjHXGL7
MZ9KRS8AfZXawmetk3jjtsV+/QkeS+Deuu7k0FoO0Th2QV7BGSDhsLXAS5By/MOC
nfSyHhnXHzCsBMyVNrJHmNhEZoN29+tRwI84JX9lWcf/OLANcCofnP6f2UIX7tZY
CAZAgVELp+0YQXdybrfzTQ8BT3TinjS/aZtCrYijRendI1GwUXcyl69vdOKqAHuk
5jy8k/xHyp+ZWu6v+PyAAAEGowY++qhL0fmszA==
=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
cpumask_first() is a more effective analogue of 'next' version if n == -1
(which means start == 0). This patch replaces 'next' with 'first' where
things look trivial.
There's no cpumask_first_zero() function, so create it.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
With the previous patch, there is an extra watchdog read in each retry.
Now the total number of clocksource reads is increased to 4 per iteration.
In order to avoid increasing the clock skew check overhead, the default
maximum number of retries is reduced from 3 to 2 to maintain the same 12
clocksource reads in the worst case.
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Since commit db3a34e174 ("clocksource: Retry clock read if long delays
detected") and commit 2e27e793e2 ("clocksource: Reduce clocksource-skew
threshold"), it is found that tsc clocksource fallback to hpet can
sometimes happen on both Intel and AMD systems especially when they are
running stressful benchmarking workloads. Of the 23 systems tested with
a v5.14 kernel, 10 of them have switched to hpet clock source during
the test run.
The result of falling back to hpet is a drastic reduction of performance
when running benchmarks. For example, the fio performance tests can
drop up to 70% whereas the iperf3 performance can drop up to 80%.
4 hpet fallbacks happened during bootup. They were:
[ 8.749399] clocksource: timekeeping watchdog on CPU13: hpet read-back delay of 263750ns, attempt 4, marking unstable
[ 12.044610] clocksource: timekeeping watchdog on CPU19: hpet read-back delay of 186166ns, attempt 4, marking unstable
[ 17.336941] clocksource: timekeeping watchdog on CPU28: hpet read-back delay of 182291ns, attempt 4, marking unstable
[ 17.518565] clocksource: timekeeping watchdog on CPU34: hpet read-back delay of 252196ns, attempt 4, marking unstable
Other fallbacks happen when the systems were running stressful
benchmarks. For example:
[ 2685.867873] clocksource: timekeeping watchdog on CPU117: hpet read-back delay of 57269ns, attempt 4, marking unstable
[46215.471228] clocksource: timekeeping watchdog on CPU8: hpet read-back delay of 61460ns, attempt 4, marking unstable
Commit 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold"),
changed the skew margin from 100us to 50us. I think this is too small
and can easily be exceeded when running some stressful workloads on a
thermally stressed system. So it is switched back to 100us.
Even a maximum skew margin of 100us may be too small in for some systems
when booting up especially if those systems are under thermal stress. To
eliminate the case that the large skew is due to the system being too
busy slowing down the reading of both the watchdog and the clocksource,
an extra consecutive read of watchdog clock is being done to check this.
The consecutive watchdog read delay is compared against
WATCHDOG_MAX_SKEW/2. If the delay exceeds the limit, we assume that
the system is just too busy. A warning will be printed to the console
and the clock skew check is skipped for this round.
Fixes: db3a34e174 ("clocksource: Retry clock read if long delays detected")
Fixes: 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-35-bigeasy@linutronix.de
Currently when an unstable clocksource is detected, the raw counters of
that clocksource and watchdog will be printed, which can only be understood
after some math calculation.
So print the delta in nanoseconds as well to make it easier for humans to
check the results.
[ paulmck: Fix typo. ]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210527190124.440372-6-paulmck@kernel.org
When the clocksource watchdog marks a clock as unstable, this might
be due to that clock being unstable or it might be due to delays that
happen to occur between the reads of the two clocks. It would be good
to have a way of testing the clocksource watchdog's ability to
distinguish between these two causes of clock skew and instability.
Therefore, provide a new clocksource-wdtest module selected by a new
TEST_CLOCKSOURCE_WATCHDOG Kconfig option. This module has a single module
parameter named "holdoff" that provides the number of seconds of delay
before testing should start, which defaults to zero when built as a module
and to 10 seconds when built directly into the kernel. Very large systems
that boot slowly may need to increase the value of this module parameter.
This module uses hand-crafted clocksource structures to do its testing,
thus avoiding messing up timing for the rest of the kernel and for user
applications. This module first verifies that the ->uncertainty_margin
field of the clocksource structures are set sanely. It then tests the
delay-detection capability of the clocksource watchdog, increasing the
number of consecutive delays injected, first provoking console messages
complaining about the delays and finally forcing a clock-skew event.
Unexpected test results cause at least one WARN_ON_ONCE() console splat.
If there are no splats, the test has passed. Finally, it fuzzes the
value returned from a clocksource to test the clocksource watchdog's
ability to detect time skew.
This module checks the state of its clocksource after each test, and
uses WARN_ON_ONCE() to emit a console splat if there are any failures.
This should enable all types of test frameworks to detect any such
failures.
This facility is intended for diagnostic use only, and should be avoided
on production systems.
Reported-by: Chris Mason <clm@fb.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-5-paulmck@kernel.org
Currently, WATCHDOG_THRESHOLD is set to detect a 62.5-millisecond skew in
a 500-millisecond WATCHDOG_INTERVAL. This requires that clocks be skewed
by more than 12.5% in order to be marked unstable. Except that a clock
that is skewed by that much is probably destroying unsuspecting software
right and left. And given that there are now checks for false-positive
skews due to delays between reading the two clocks, it should be possible
to greatly decrease WATCHDOG_THRESHOLD, at least for fine-grained clocks
such as TSC.
Therefore, add a new uncertainty_margin field to the clocksource structure
that contains the maximum uncertainty in nanoseconds for the corresponding
clock. This field may be initialized manually, as it is for
clocksource_tsc_early and clocksource_jiffies, which is copied to
refined_jiffies. If the field is not initialized manually, it will be
computed at clock-registry time as the period of the clock in question
based on the scale and freq parameters to __clocksource_update_freq_scale()
function. If either of those two parameters are zero, the
tens-of-milliseconds WATCHDOG_THRESHOLD is used as a cowardly alternative
to dividing by zero. No matter how the uncertainty_margin field is
calculated, it is bounded below by twice WATCHDOG_MAX_SKEW, that is, by 100
microseconds.
Note that manually initialized uncertainty_margin fields are not adjusted,
but there is a WARN_ON_ONCE() that triggers if any such field is less than
twice WATCHDOG_MAX_SKEW. This WARN_ON_ONCE() is intended to discourage
production use of the one-nanosecond uncertainty_margin values that are
used to test the clock-skew code itself.
The actual clock-skew check uses the sum of the uncertainty_margin fields
of the two clocksource structures being compared. Integer overflow is
avoided because the largest computed value of the uncertainty_margin
fields is one billion (10^9), and double that value fits into an
unsigned int. However, if someone manually specifies (say) UINT_MAX,
they will get what they deserve.
Note that the refined_jiffies uncertainty_margin field is initialized to
TICK_NSEC, which means that skew checks involving this clocksource will
be sufficently forgiving. In a similar vein, the clocksource_tsc_early
uncertainty_margin field is initialized to 32*NSEC_PER_MSEC, which
replicates the current behavior and allows custom setting if needed
in order to address the rare skews detected for this clocksource in
current mainline.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-4-paulmck@kernel.org
Currently, if skew is detected on a clock marked CLOCK_SOURCE_VERIFY_PERCPU,
that clock is checked on all CPUs. This is thorough, but might not be
what you want on a system with a few tens of CPUs, let alone a few hundred
of them.
Therefore, by default check only up to eight randomly chosen CPUs. Also
provide a new clocksource.verify_n_cpus kernel boot parameter. A value of
-1 says to check all of the CPUs, and a non-negative value says to randomly
select that number of CPUs, without concern about selecting the same CPU
multiple times. However, make use of a cpumask so that a given CPU will be
checked at most once.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> # For verify_n_cpus=1.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-3-paulmck@kernel.org
Some sorts of per-CPU clock sources have a history of going out of
synchronization with each other. However, this problem has purportedy been
solved in the past ten years. Except that it is all too possible that the
problem has instead simply been made less likely, which might mean that
some of the occasional "Marking clocksource 'tsc' as unstable" messages
might be due to desynchronization. How would anyone know?
Therefore apply CPU-to-CPU synchronization checking to newly unstable
clocksource that are marked with the new CLOCK_SOURCE_VERIFY_PERCPU flag.
Lists of desynchronized CPUs are printed, with the caveat that if it
is the reporting CPU that is itself desynchronized, it will appear that
all the other clocks are wrong. Just like in real life.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-2-paulmck@kernel.org
When the clocksource watchdog marks a clock as unstable, this might be due
to that clock being unstable or it might be due to delays that happen to
occur between the reads of the two clocks. Yes, interrupts are disabled
across those two reads, but there are no shortage of things that can delay
interrupts-disabled regions of code ranging from SMI handlers to vCPU
preemption. It would be good to have some indication as to why the clock
was marked unstable.
Therefore, re-read the watchdog clock on either side of the read from the
clock under test. If the watchdog clock shows an excessive time delta
between its pair of reads, the reads are retried.
The maximum number of retries is specified by a new kernel boot parameter
clocksource.max_cswd_read_retries, which defaults to three, that is, up to
four reads, one initial and up to three retries. If more than one retry
was required, a message is printed on the console (the occasional single
retry is expected behavior, especially in guest OSes). If the maximum
number of retries is exceeded, the clock under test will be marked
unstable. However, the probability of this happening due to various sorts
of delays is quite small. In addition, the reason (clock-read delays) for
the unstable marking will be apparent.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-1-paulmck@kernel.org
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation,
zap under read lock, enable/disably dirty page logging under
read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing
the architecture-specific code
- Some selftests improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCJ13kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM1HAgAqzPxEtiTPTFeFJV5cnPPJ3dFoFDK
y/juZJUQ1AOtvuWzzwuf175ewkv9vfmtG6rVohpNSkUlJYeoc6tw7n8BTTzCVC1b
c/4Dnrjeycr6cskYlzaPyV6MSgjSv5gfyj1LA5UEM16LDyekmaynosVWY5wJhju+
Bnyid8l8Utgz+TLLYogfQJQECCrsU0Wm//n+8TWQgLf1uuiwshU5JJe7b43diJrY
+2DX+8p9yWXCTz62sCeDWNahUv8AbXpMeJ8uqZPYcN1P0gSEUGu8xKmLOFf9kR7b
M4U1Gyz8QQbjd2lqnwiWIkvRLX6gyGVbq2zH0QbhUe5gg3qGUX7JjrhdDQ==
=AXUi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
System time snapshots are not conveying information about the current
clocksource which was used, but callers like the PTP KVM guest
implementation have the requirement to evaluate the clocksource type to
select the appropriate mechanism.
Introduce a clocksource id field in struct clocksource which is by default
set to CSID_GENERIC (0). Clocksource implementations can set that field to
a value which allows to identify the clocksource.
Store the clocksource id of the current clocksource in the
system_time_snapshot so callers can evaluate which clocksource was used to
take the snapshot and act accordingly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201209060932.212364-5-jianyong.wu@arm.com
With Arm EBSA110 gone, nothing uses it any more, so the corresponding
code and the Kconfig option can be removed.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_GENERIC_VDSO_CLOCK_MODE was a transitional config switch which got
removed after all architectures got converted to the new storage model.
But the removal forgot to remove the #ifdef which guards the
vdso_clock_mode sanity check, which effectively disables the sanity check.
Remove it now.
Fixes: f86fd32db7 ("lib/vdso: Cleanup clock mode storage leftovers")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200606221531.845475036@linutronix.de
All architectures which use the generic VDSO code have their own storage
for the VDSO clock mode. That's pointless and just requires duplicate code.
Provide generic storage for it. The new Kconfig symbol is intermediate and
will be removed once all architectures are converted over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.028046322@linutronix.de
Kernel crashes inside QEMU/KVM are observed:
kernel BUG at kernel/time/timer.c:1154!
BUG_ON(timer_pending(timer) || !timer->function) in add_timer_on().
At the same time another cpu got:
general protection fault: 0000 [#1] SMP PTI of poinson pointer 0xdead000000000200 in:
__hlist_del at include/linux/list.h:681
(inlined by) detach_timer at kernel/time/timer.c:818
(inlined by) expire_timers at kernel/time/timer.c:1355
(inlined by) __run_timers at kernel/time/timer.c:1686
(inlined by) run_timer_softirq at kernel/time/timer.c:1699
Unfortunately kernel logs are badly scrambled, stacktraces are lost.
Printing the timer->function before the BUG_ON() pointed to
clocksource_watchdog().
The execution of clocksource_watchdog() can race with a sequence of
clocksource_stop_watchdog() .. clocksource_start_watchdog():
expire_timers()
detach_timer(timer, true);
timer->entry.pprev = NULL;
raw_spin_unlock_irq(&base->lock);
call_timer_fn
clocksource_watchdog()
clocksource_watchdog_kthread() or
clocksource_unbind()
spin_lock_irqsave(&watchdog_lock, flags);
clocksource_stop_watchdog();
del_timer(&watchdog_timer);
watchdog_running = 0;
spin_unlock_irqrestore(&watchdog_lock, flags);
spin_lock_irqsave(&watchdog_lock, flags);
clocksource_start_watchdog();
add_timer_on(&watchdog_timer, ...);
watchdog_running = 1;
spin_unlock_irqrestore(&watchdog_lock, flags);
spin_lock(&watchdog_lock);
add_timer_on(&watchdog_timer, ...);
BUG_ON(timer_pending(timer) || !timer->function);
timer_pending() -> true
BUG()
I.e. inside clocksource_watchdog() watchdog_timer could be already armed.
Check timer_pending() before calling add_timer_on(). This is sufficient as
all operations are synchronized by watchdog_lock.
Fixes: 75c5158f70 ("timekeeping: Update clocksource with stop_machine")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/158048693917.4378.13823603769948933793.stgit@buzz
The inline keyword was not at the beginning of the function declarations.
Fix the following warnings triggered when using W=1:
kernel/time/clocksource.c:108:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
kernel/time/clocksource.c:113:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: trivial@kernel.org
Cc: kernel-janitors@vger.kernel.org
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190524103339.28787-1-malat@debian.org
The SPDX identifier defines the license of the files already. No need for
the boilerplates.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: David Riley <davidriley@chromium.org>
Cc: Colin Cross <ccross@android.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20181031182253.132458951@linutronix.de
Update the time(r) core files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of the
full boiler plate text.
This work is based on a script and data from Philippe Ombredanne, Kate
Stewart and myself. The data has been created with two independent license
scanners and manual inspection.
The following files do not contain any direct license information and have
been omitted from the big initial SPDX changes:
timeconst.bc: The .bc files were not touched
time.c, timer.c, timekeeping.c: Licence was deduced from EXPORT_SYMBOL_GPL
As those files do not contain direct license references they fall under the
project license, i.e. GPL V2 only.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: David Riley <davidriley@chromium.org>
Cc: Colin Cross <ccross@android.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20181031182252.879109557@linutronix.de
Remove the pointless filenames in the top level comments. They have no
value at all and just occupy space. While at it tidy up some of the
comments and remove a stale one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Riley <davidriley@chromium.org>
Cc: Colin Cross <ccross@android.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lkml.kernel.org/r/20181031182252.794898238@linutronix.de
Architectures have extra archdata in the clocksource, e.g. for VDSO
support. There are no sanity checks or general initializations for this
available. Add support for that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Rickard <matt@softrans.com.au>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20180917130706.973042587@linutronix.de
I turns out that the silly spawn kthread from worker was actually needed.
clocksource_watchdog_kthread() cannot be called directly from
clocksource_watchdog_work(), because clocksource_select() calls
timekeeping_notify() which uses stop_machine(). One cannot use
stop_machine() from a workqueue() due lock inversions wrt CPU hotplug.
Revert the patch but add a comment that explain why we jump through such
apparently silly hoops.
Fixes: 7197e77abc ("clocksource: Remove kthread")
Reported-by: Siegfried Metz <frame@mailbox.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Kevin Shanahan <kevin@shanahan.id.au>
Tested-by: viktor_jaegerskuepper@freenet.de
Tested-by: Siegfried Metz <frame@mailbox.org>
Cc: rafael.j.wysocki@intel.com
Cc: len.brown@intel.com
Cc: diego.viola@gmail.com
Cc: rui.zhang@intel.com
Cc: bjorn.andersson@linaro.org
Link: https://lkml.kernel.org/r/20180905084158.GR24124@hirez.programming.kicks-ass.net
On some hardware with multiple clocksources, we have coarse grained
clocksources that support the CLOCK_SOURCE_SUSPEND_NONSTOP flag, but
which are less than ideal for timekeeping whereas other clocksources
can be better candidates but halt on suspend.
Currently, the timekeeping core only supports timing suspend using
CLOCK_SOURCE_SUSPEND_NONSTOP clocksources if that clocksource is the
current clocksource for timekeeping.
As a result, some architectures try to implement read_persistent_clock64()
using those non-stop clocksources, but isn't really ideal, which will
introduce more duplicate code. To fix this, provide logic to allow a
registered SUSPEND_NONSTOP clocksource, which isn't the current
clocksource, to be used to calculate the suspend time.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
[jstultz: minor tweaks to merge with previous resume changes]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The inline keyword was not at the beginning of the function declarations.
Fix the following warnings triggered when using W=1:
kernel/time/clocksource.c:456:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
kernel/time/clocksource.c:457:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lkml.kernel.org/r/20180516195943.31924-1-malat@debian.org
A number of places relies on list_empty(&cs->wd_list), however the
list_head does not get initialized. Do so upon registration, such that
thereafter it is possible to rely on list_empty() correctly reflecting
the list membership status.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Diego Viola <diego.viola@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
Cc: len.brown@intel.com
Cc: rjw@rjwysocki.net
Cc: rui.zhang@intel.com
Link: https://lkml.kernel.org/r/20180430100344.472662715@infradead.org
Because of how the code flips between tsc-early and tsc clocksources
it might need to mark one or both unstable. The current code in
mark_tsc_unstable() only worked because previously it registered the
tsc clocksource once and then never touched it.
Since it now unregisters the tsc-early clocksource, it needs to know
if a clocksource got unregistered and the current cs->mult test
doesn't work for that. Instead use list_empty(&cs->list) to test for
registration.
Furthermore, since clocksource_mark_unstable() needs to place the cs
on the wd_list, it links the cs->list and cs->wd_list serialization.
It must not see a clocsource registered (!empty cs->list) but already
past dequeue_watchdog(). So place {en,de}queue{,_watchdog}() under the
same lock.
Provided cs->list is initialized to empty, this then allows us to
unconditionally use clocksource_mark_unstable(), regardless of the
registration state.
Fixes: aa83c45762 ("x86/tsc: Introduce early tsc clocksource")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Diego Viola <diego.viola@gmail.com>
Cc: len.brown@intel.com
Cc: rjw@rjwysocki.net
Cc: diego.viola@gmail.com
Cc: rui.zhang@intel.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180502135312.GS12217@hirez.programming.kicks-ass.net
Adrian Hunter