Factor out all the differences between MLX90614 and other similar chips
into a structure which describes the chip and allows abstracting out the
differences from the driver code. No functional change.
This patch moves all the RAM and EEPROM IO opcodes into the descriptor
structure and combines them, instead of combining the opcode and offset
in macros.
Acked-by: Crt Mori <cmo@melexis.com>
Tested-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230510102251.10118-5-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MLX90614_CONST_EMISSIVITY_RESOLUTION can be calculated from
MLX90614_CONST_RAW_EMISSIVITY_MAX, perform the calculation inline
and drio the MLX90614_CONST_EMISSIVITY_RESOLUTION.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/20230510102251.10118-4-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To simplify addition of support for new parts, drop unused register macros.
No functional change.
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230510102251.10118-3-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sort the headers alphabetically. No functional change.
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230510102251.10118-2-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Honeywell mprls0025pa is a series of pressure sensors.
Add initial I2C support.
Note:
- IIO buffered mode is supported
- SPI mode is not supported
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Link: https://lore.kernel.org/r/ZGNp3SqyOJeEcLsj@arbad
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230515205048.19561-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.
Fixes: ec74ae9fd3 ("iio: imu: inv_icm42600: add accurate timestamping")
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230509152202.245444-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230516110038.2413224-13-schnelle@linux.ibm.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Renesas X9250 integrates four digitally controlled potentiometers.
On each potentiometer, the X9250T has a 100 kOhms total resistance and
the X9250U has a 50 kOhms total resistance.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230509160852.158101-3-herve.codina@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Sigma-Delta ADCs supported by this driver can use SDO as an interrupt
line to indicate the completion of a conversion. However, some devices
cannot properly detect the completion of a conversion by an interrupt.
This is for the reason mentioned in the following commit.
commit e9849777d0 ("genirq: Add flag to force mask in
disable_irq[_nosync]()")
A read operation is performed by an extra interrupt before the completion
of a conversion. At this time, the value read from the ADC data register
is the same as the previous conversion result. This patch fixes the issue
by setting IRQ_DISABLE_UNLAZY flag.
Fixes: 0c6ef985a1 ("iio: adc: ad7791: fix IRQ flags")
Fixes: 1a913270e5 ("iio: adc: ad7793: Fix IRQ flag")
Fixes: e081102f30 ("iio: adc: ad7780: Fix IRQ flag")
Fixes: 89a86da5cb ("iio: adc: ad7192: Add IRQ flag")
Fixes: 79ef91493f ("iio: adc: ad7124: Set IRQ type to falling")
Signed-off-by: Masahiro Honda <honda@mechatrax.com>
Link: https://lore.kernel.org/r/20230518110816.248-1-honda@mechatrax.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
Fixes: cf35ad61ac ("iio: add mcp4725 I2C DAC driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230511004330.206942-1-marex@denx.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The fwnode_irq_get_byname() was returning 0 at device-tree mapping
error. If this occurred, the KX022A driver did abort the probe but
errorneously directly returned the return value from
fwnode_irq_get_byname() from probe. In case of a device-tree mapping
error this indicated success.
The fwnode_irq_get_byname() has since been fixed to not return zero on
error so the check for fwnode_irq_get_byname() can be relaxed to only
treat negative values as errors. This will also do decent fix even when
backported to branches where fwnode_irq_get_byname() can still return
zero on error because KX022A probe should later fail at IRQ requesting
and a prober error handling should follow.
Relax the return value check for fwnode_irq_get_byname() to only treat
negative values as errors.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202305110245.MFxC9bUj-lkp@intel.com/
Link: https://lore.kernel.org/r/202305110245.MFxC9bUj-lkp@intel.com/
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 7c1d1677b3 ("iio: accel: Support Kionix/ROHM KX022A accelerometer")
Link: https://lore.kernel.org/r/b45b4b638db109c6078d243252df3a7b0485f7d5.1683875389.git.mazziesaccount@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset bit must be always written to the hardware no matter what value
is in a cache or register. Ensure this by using regmap_write_bits()
instead of the regmap_update_bits(). Furthermore, the SWRESET bit may be
self-clearing, so mark the SYSTEM_CONTROL register volatile to guarantee
we do also read the right state - should we ever need to read it.
Finally, writing the SWRESET bit will restore the default register
values. This can cause register cache to be outdated if there are any
register values cached.
Rebuild register cache after SWRESET and use regmap_update_bits() when
performing the reset.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: e52afbd610 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Link: https://lore.kernel.org/r/ZFjWhbfuN5XcKty+@fedora
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 28d1a7ac2a ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
Fixes: 28d1a7ac2a ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Invensense ICM-20600 is a 6-axis MotionTracking device that combines a
3-axis gyroscope and an 3-axis accelerometer. It is very similar to the
ICM20602 imu which is already supported by the mpu6050 driver. The main
difference is that the ICM-20600 has a different WHOAMI value.
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230505054853.2155326-3-chenhuiz@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set the read_label() callback to return a friendly name provided in DT
(firmware), in order to make in_{therm,voltage}X_label attributes show
up in sysfs for userspace to consume a channel name. This is
particularly useful for custom thermistors being attached to otherwise
generically named GPIOs, where the name is known by the board DT.
If the channel name isn't set in DT, use the datasheet_name hardcoded in
the driver instead.
Note that this doesn't fall back to fwnode_get_name() as that provides
suboptimally readable names, with an @xx address suffix from board DT.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-5-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the migration to fwnode_get_name in commit 4f47a236a2 ("iio:
adc: qcom-spmi-adc5: convert to device properties") the resulting
adc5_channel_prop::channel_name (renamed from datasheet_name in the
previous patch) - which is propagated into iio_chan_spec::extend_name -
was containing the DT node name including @xx suffix if a "label"
property is not present, while adc5_channels::datasheet_name was thus
far set by the macros but always remained unread. Put it to use instead
of using a confusing name containing @xx in sysfs filenames (again, when
"label" is not set).
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-3-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_chan_spec::datasheet_name expects a channel/pin name on the hardware
part, i.e. from its datasheet, instead of a friendly name from DT which
typically describes the use of said channel. GPIO channels are commonly
specialized in QCOM board DTS based on what a - typically thermistor -
is connected to.
Also rename adc5_channel_prop::datasheet_name to channel_name to that
effect.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-2-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Devices which may take a while to initialize during probe and which have
no strong reason to probe synchronously can request asynchronous probing
as default probe strategy. This can speed-up start times on some
platforms.
The KX022A gets probe delayed for at least two reasons. It enables the
supply regulator, (which is likely to have ramp-up delay if it was
disabled) and additionally it delays while the sensor itself is
initializing.
Changing to asynchronous probing may cause problems. Some of which are
discussed in:
https://lore.kernel.org/all/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk/
Enable asynchronous probing for KX022A.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/24cea76c282a28b7a4dba297ab627176f8097907.1683185765.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Devices which may take a while to initialize during probe and which have
no strong reason to probe synchronously can request asynchronous probing
as default probe strategy. This can speed-up start times on some
platforms.
The BU27034 gets probe delayed for at least two reasons. It enables the
supply regulator, (which is likely to have ramp-up delay if it was
disabled) and additionally it delays while the sensor itself is
initializing.
Changing to asynchronous probing may cause problems. Some of which are
discussed in:
https://lore.kernel.org/all/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk/
Enabling async probing for the ROHM BU27034 should be fairly safe to try
though as there is no in-tree users for it yet. If the async probing
appears to be an issue we can switch easily back to synchronous (or
better yet, fix the actual problem).
Enable asynchronous probing for BU27034.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/e7088793e1868c77b1894b30cd026e8ed043ea7c.1683185765.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Just cosmetics. No functional change intended...
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230216101452.591805-4-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver uses the continuous mode of the chip and integration
time can be configured through sysfs.
The constants for calculating lux value differs between packaging
so it uses different compatible string for the two versions
"ti,opt4001-picostar" and "ti,opt4001-sot-5x3" since the device id
is the same.
Datasheet: https://www.ti.com/lit/gpn/opt4001
Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Link: https://lore.kernel.org/r/20230323-add-opt4001-driver-v3-2-62e121dab294@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since nearly all stm32 dt's are using the legacy adc channel config,
we should warn users about using it.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20230421083858.2613289-1-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor can be found as CALS0001 on the Lenovo Yoga
Tablet 2 series.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230420232631.68864-1-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d can be found as ACCL0001 on various Lenovo devices,
including the Lenovo Yoga Tablet 2 1051-F, where I tested this
patch.
Dropped SPI support as per discussion in thread linked below.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-5-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d is basically the lsm9ds0 without the gyroscope
(which the LSM9DS0 IMU driver doesn't handle), as far as I
can tell.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-4-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d has the same register mapping as the lsm9ds0,
thus we can just re-use that.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-3-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d has the same register mapping as the lsm9ds0,
thus we can just re-use that.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-2-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On success, ad74413r_get_single_adc_result() returns IIO_VAL_INT aka
1. So currently, the IIO_CHAN_INFO_PROCESSED case is effectively
equivalent to the IIO_CHAN_INFO_RAW case, and we never call
ad74413r_adc_to_resistance_result() to convert the adc measurement to
ohms.
Check ret for being negative rather than non-zero.
Fixes: fea251b6a5 (iio: addac: add AD74413R driver)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230503095817.452551-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If only adc differential channels are defined driver will fail with
stm32-adc: probe of 48003000.adc:adc@0 failed with error -22
Fix this by skipping the initialization if no channels are defined.
This applies only to the legacy way of initializing adc channels.
Fixes: d7705f3544 ("iio: adc: stm32-adc: convert to device properties")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20230503162029.3654093-2-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If no adc differential channels are defined driver will fail with EINVAL:
stm32-adc: probe of 48003000.adc:adc@0 failed with error -22
Fix this by skipping the initialization if no channels are defined.
This applies only to the legacy way of initializing adc channels.
Fixes: d7705f3544 ("iio: adc: stm32-adc: convert to device properties")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20230503162029.3654093-1-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Alisa Roman <alisa.roman@analog.com>
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When apply_acpi_orientation() fails, st_accel_common_probe() will fall back
to iio_read_mount_matrix(), which checks for a mount-matrix device property
and if that is not set falls back to the identity matrix.
But when a sensor has no ACPI companion fwnode, or when the ACPI fwnode
does not have a "_ONT" method apply_acpi_orientation() was returning 0,
causing iio_read_mount_matrix() to never get called resulting in an
invalid mount_matrix:
[root@fedora ~]# cat /sys/bus/iio/devices/iio\:device0/mount_matrix
(null), (null), (null); (null), (null), (null); (null), (null), (null)
Fix this by making apply_acpi_orientation() always return an error when
it did not set the mount_matrix.
Fixes: 3d8ad94bb1 ("iio: accel: st_sensors: Support generic mounting matrix")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Marius Hoch <mail@mariushoch.de>
Link: https://lore.kernel.org/r/20230416212409.310936-1-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO ABI mandates expressing integration times in seconds. The GTS
helper errorneously uses micro seconds in integration_times_available.
Fix this by converting the lists to IIO_VAL_INT_PLUS_MICRO.
Fixes: 38416c28e1 ("iio: light: Add gain-time-scale helpers")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/eeacd192c259e885850b5a2dd8b776bccfc44fa8.1681722914.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bu27034 uses micro seconds for integration time configuration. This
is incorrect as the ABI mandates use of seconds.
Change BU27034 driver to use seconds for integration time.
Fixes: e52afbd610 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/a05647669af22ba919c7c87dccb43975e3235a87.1681722914.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Valid values for "adc_chan" are zero to (PALMAS_ADC_CH_MAX - 1).
Smatch detects some buffer overflows caused by this:
drivers/iio/adc/palmas_gpadc.c:721 palmas_gpadc_read_event_value() error: buffer overflow 'adc->thresholds' 16 <= 16
drivers/iio/adc/palmas_gpadc.c:758 palmas_gpadc_write_event_value() error: buffer overflow 'adc->thresholds' 16 <= 16
The effect of this bug in other functions is more complicated but
obviously we should fix all of them.
Fixes: a99544c6c8 ("iio: adc: palmas: add support for iio threshold events")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/14fee94a-7db7-4371-b7d6-e94d86b9561e@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Smatch reports:
drivers/iio/adc/mxs-lradc-adc.c:766 mxs_lradc_adc_probe() warn:
missing unwind goto?
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad4130 driver registers a clock provider, but never removes it. This
leaves a stale clock provider behind that references freed clocks when the
device is unbound.
Register a managed action to remove the clock provider when the device is
removed.
Fixes: 62094060cf ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230414150702.518441-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The tmag5273 gets a runtime PM reference before reading a measurement and
releases it when done. But if the measurement fails the tmag5273_read_raw()
function exits before releasing the reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: 866a138917 ("iio: magnetometer: add ti tmag5273 driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230414013752.498767-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The scale value of ibus and ibat on the datasheet is incorrect due to the
customer report after the experimentation with some specific vendor ID
chips.
Fixes: c1404d1b65 ("iio: adc: mt6370: Add MediaTek MT6370 support")
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/1681122862-1994-1-git-send-email-chiaen_wu@richtek.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The problem is these lines:
ret = vref_uv = regulator_get_voltage(adc->vref);
if (ret < 0)
The "ret" variable is type long and "vref_uv" is u32 so that means
the condition can never be true on a 64bit system. A negative error
code from regulator_get_voltage() would be cast to a high positive
u32 value and then remain a high positive value when cast to a long.
The "ret" variable only ever stores ints so it should be declared as
an int. We can delete the "vref_uv" variable and use "ret" directly.
Fixes: 7d02296ac8 ("iio: adc: add imx93 adc support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/Y+utEvjfjQRQo2QB@kili
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
A fairly standard release for SPI with the exception of a change to the
API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily for
a while. There's also a new API to allow us to TPM chips on half duplex
controllers.
There's three commits in here that were mangled by a bad interaction
between the alsa-devel mailing list software and b4, I didn't notice
until there were merges on top with it being SPI not ALSA. It seemed
clear enough to not be worth going back and fixing.
- Refactoring in preparation for supporting multiple chip selects for a
single device, needed by some flash devices, which required a change
in the SPI device API visible throughout the tree.
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI.
- Optimisation for large transfers on fsl-cpm devices.
- Cleanups around device property use which fix some sisues with
fwnode.
- Use of both void remove() and devm_platform_.*ioremap_resource().
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI.
The final commit converting to DEV_PM_OPS() was applied late to fix a
warning that was introduced by some of the earlier work.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmRIFQgACgkQJNaLcl1U
h9BJOwf+JF2RySdn5g1LsyTndPZhLfw4iJgTHaMlnv5tiPHvYVYMM/mNMbMr5Znh
Y2T0OUkzuRfOK273C+hItC1bTYFTa2cEbDb5dpmKBOZdQ3hjGsZQBvuH2bScUQ+a
H7UgD3FYOJST6k6rRgZQxVMPePFrXAOaO1gmFWTR3v1EcEr2JeQnjZsmymFXcTnc
CtPg9N3RvhVnq5aXuxSgQeyyKIjo4LJh/eZ2mexPIu0DeUq3MftaWwSwCXFIoeNC
DMLA4mZWTgf/yt6JUALwLr+bIiJjb4qGjp3xGZ2wmX7zn73f9QQvuunKb1V4zbNF
EdXLo2VjA9cZjsihenBaKeHnkfgNfA==
=IRqY
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly standard release for SPI with the exception of a change to
the API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily
for a while.
There's also a new API to allow us to support TPM chips on half duplex
controllers.
Summary:
- Refactoring in preparation for supporting multiple chip selects for
a single device, needed by some flash devices, which required a
change in the SPI device API visible throughout the tree
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI
- Optimisation for large transfers on fsl-cpm devices
- Cleanups around device property use which fix some sisues with
fwnode
- Use of both void remove() and devm_platform_.*ioremap_resource()
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI"
* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: tegra210-quad: Enable TPM wait polling
spi: Add TPM HW flow flag
spi: bcm63xx: remove PM_SLEEP based conditional compilation
spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: spi-cadence: Add support for Slave mode
spi: spi-cadence: Switch to spi_controller structure
spi: cadence-quadspi: fix suspend-resume implementations
spi: dw: Add support for AMD Pensando Elba SoC
spi: dw: Add AMD Pensando Elba SoC SPI Controller
spi: cadence-quadspi: Disable the SPI before reconfiguring
spi: cadence-quadspi: Update the read timeout based on the length
spi: spi-loopback-test: Add module param for iteration length
spi: add support for Amlogic A1 SPI Flash Controller
dt-bindings: spi: add Amlogic A1 SPI controller
spi: fsl-spi: No need to check transfer length versus word size
spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
spi: fsl-cpm: Use 16 bit mode for large transfers with even size
spi: fsl-spi: Re-organise transfer bits_per_word adaptation
spi: fsl-spi: Fix CPM/QE mode Litte Endian
...
- Update the ACPICA code in the kernel to upstream revision 20230331
including the following changes:
* Delete bogus node_array array of pointers from AEST table (Jessica
Clarke).
* Add support for trace buffer extension in GICC to the ACPI MADT
parser (Xiongfeng Wang).
* Add missing macro ACPI_FUNCTION_TRACE() for acpi_ns_repair_HID()
(Xiongfeng Wang).
* Add missing tables to astable (Pedro Falcato).
* Add support for 64 bit loong_arch compilation to ACPICA (Huacai
Chen).
* Add support for ASPT table in disassembler to ACPICA (Jeremi
Piotrowski).
* Add support for Arm's MPAM ACPI table version 2 (Hesham Almatary).
* Update all copyrights/signons in ACPICA to 2023 (Bob Moore).
* Add support for ClockInput resource (v6.5) (Niyas Sait).
* Add RISC-V INTC interrupt controller definition to the list of
supported interrupt controllers for MADT (Sunil V L).
* Add structure definitions for the RISC-V RHCT ACPI table (Sunil V L).
* Address several cases in which the ACPICA code might lead to
undefined behavior (Tamir Duberstein).
* Make ACPICA code support flexible arrays properly (Kees Cook).
* Check null return of ACPI_ALLOCATE_ZEROED in
acpi_db_display_objects() (void0red).
* Add os specific support for Zephyr RTOS to ACPICA (Najumon).
* Update version to 20230331 (Bob Moore).
- Fix evaluating the _PDC ACPI control method when running as Xen
dom0 (Roger Pau Monne).
- Use platform devices to load ACPI PPC and PCC drivers (Petr Pavlu).
- Check for null return of devm_kzalloc() in fch_misc_setup() (Kang
Chen).
- Log a message if enable_irq_wake() fails for the ACPI SCI (Simon
Gaiser).
- Initialize the correct IOMMU fwspec while parsing ACPI VIOT
(Jean-Philippe Brucker).
- Amend indentation and prefix error messages with FW_BUG in the ACPI
SPCR parsing code (Andy Shevchenko).
- Enable ACPI sysfs support for CCEL records (Kuppuswamy
Sathyanarayanan).
- Make the APEI error injection code warn on invalid arguments when
explicitly indicated by platform (Shuai Xue).
- Add CXL error types to the error injection code in APEI (Tony Luck).
- Refactor acpi_data_prop_read_single() (Andy Shevchenko).
- Fix two issues in the ACPI SBS driver (Armin Wolf).
- Replace ternary operator with min_t() in the generic ACPI thermal
zone driver (Jiangshan Yi).
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki).
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede).
- Replace irqdomain.h include with struct declarations in ACPI headers
and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring).
- Fix acpi_evaluate_dsm_typed() redefinition error (Kiran K).
- Update the pm_profile sysfs attribute documentation (Rafael Wysocki).
- Add 80862289 ACPI _HID for second PWM controller on Cherry Trail to
the ACPI driver for Intel SoCs (Hans de Goede).
-----BEGIN PGP SIGNATURE-----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=O61K
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20230331, fix the ACPI SBS driver and the evaluation of the _PDC
method on Xen dom0 in the ACPI processor driver, update the ACPI
driver for Intel SoCs and clean up code in multiple places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20230331
including the following changes:
* Delete bogus node_array array of pointers from AEST table
(Jessica Clarke)
* Add support for trace buffer extension in GICC to the ACPI MADT
parser (Xiongfeng Wang)
* Add missing macro ACPI_FUNCTION_TRACE() for
acpi_ns_repair_HID() (Xiongfeng Wang)
* Add missing tables to astable (Pedro Falcato)
* Add support for 64 bit loong_arch compilation to ACPICA (Huacai
Chen)
* Add support for ASPT table in disassembler to ACPICA (Jeremi
Piotrowski)
* Add support for Arm's MPAM ACPI table version 2 (Hesham
Almatary)
* Update all copyrights/signons in ACPICA to 2023 (Bob Moore)
* Add support for ClockInput resource (v6.5) (Niyas Sait)
* Add RISC-V INTC interrupt controller definition to the list of
supported interrupt controllers for MADT (Sunil V L)
* Add structure definitions for the RISC-V RHCT ACPI table (Sunil
V L)
* Address several cases in which the ACPICA code might lead to
undefined behavior (Tamir Duberstein)
* Make ACPICA code support flexible arrays properly (Kees Cook)
* Check null return of ACPI_ALLOCATE_ZEROED in
acpi_db_display_objects() (void0red)
* Add os specific support for Zephyr RTOS to ACPICA (Najumon)
* Update version to 20230331 (Bob Moore)
- Fix evaluating the _PDC ACPI control method when running as Xen
dom0 (Roger Pau Monne)
- Use platform devices to load ACPI PPC and PCC drivers (Petr Pavlu)
- Check for null return of devm_kzalloc() in fch_misc_setup() (Kang
Chen)
- Log a message if enable_irq_wake() fails for the ACPI SCI (Simon
Gaiser)
- Initialize the correct IOMMU fwspec while parsing ACPI VIOT
(Jean-Philippe Brucker)
- Amend indentation and prefix error messages with FW_BUG in the ACPI
SPCR parsing code (Andy Shevchenko)
- Enable ACPI sysfs support for CCEL records (Kuppuswamy
Sathyanarayanan)
- Make the APEI error injection code warn on invalid arguments when
explicitly indicated by platform (Shuai Xue)
- Add CXL error types to the error injection code in APEI (Tony Luck)
- Refactor acpi_data_prop_read_single() (Andy Shevchenko)
- Fix two issues in the ACPI SBS driver (Armin Wolf)
- Replace ternary operator with min_t() in the generic ACPI thermal
zone driver (Jiangshan Yi)
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki)
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede)
- Replace irqdomain.h include with struct declarations in ACPI
headers and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring)
- Fix acpi_evaluate_dsm_typed() redefinition error (Kiran K)
- Update the pm_profile sysfs attribute documentation (Rafael
Wysocki)
- Add 80862289 ACPI _HID for second PWM controller on Cherry Trail to
the ACPI driver for Intel SoCs (Hans de Goede)"
* tag 'acpi-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: LPSS: Add 80862289 ACPI _HID for second PWM controller on Cherry Trail
ACPI: bus: Ensure that notify handlers are not running after removal
ACPI: bus: Add missing braces to acpi_sb_notify()
ACPI: video: Remove desktops without backlight DMI quirks
ACPI: video: Remove register_backlight_delay module option and code
ACPI: Replace irqdomain.h include with struct declarations
fpga: lattice-sysconfig-spi: Add explicit include for of.h
tpm: atmel: Add explicit include for of.h
virtio-mmio: Add explicit include for of.h
pata: ixp4xx: Add explicit include for of.h
ata: pata_macio: Add explicit include of irqdomain.h
serial: 8250_tegra: Add explicit include for of.h
net: rfkill-gpio: Add explicit include for of.h
staging: iio: resolver: ad2s1210: Add explicit include for of.h
iio: adc: ad7292: Add explicit include for of.h
ACPICA: Update version to 20230331
ACPICA: add os specific support for Zephyr RTOS
ACPICA: ACPICA: check null return of ACPI_ALLOCATE_ZEROED in acpi_db_display_objects
ACPICA: acpi_resource_irq: Replace 1-element arrays with flexible array
ACPICA: acpi_madt_oem_data: Fix flexible array member definition
...
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano).
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano).
- Clean up the hwmon thermal driver (Daniel Lezcano).
- Add thermal zone id accessor and thermal zone type accessor
and prevent drivers from using thermal zone fields directly (Daniel
Lezcano).
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano).
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui).
- Add more thermal zone device encapsulation: prevent setting structure
field directly, access the sensor device instead the thermal zone's
device for trace, relocate the traces in drivers/thermal (Daniel
Lezcano).
- Use the generic trip point for the i.MX and remove the get_trip_temp
ops (Daniel Lezcano).
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li).
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown (Wolfram
Sang).
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur).
- Add MT8365 support (Amjad Ouled-Ameur).
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel).
- Add driver support for RK3588 (Finley Xiao).
- Use devm_reset_control_array_get_exclusive() for the Rockchip driver
(Ye Xingchen).
- Detect power gated thermal zones and return -EAGAIN when reading the
temperature (Mikko Perttunen).
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring).
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn).
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai).
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen).
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI).
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano).
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano).
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano).
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui).
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki).
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring).
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki).
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada).
-----BEGIN PGP SIGNATURE-----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=XNJE
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly continue to prepare the thermal control subsystem for
using unified representation of trip points, which includes cleanups,
code refactoring and similar and update several drivers (for other
reasons), which includes new hardware support.
Specifics:
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano)
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano)
- Clean up the hwmon thermal driver (Daniel Lezcano)
- Add thermal zone id accessor and thermal zone type accessor and
prevent drivers from using thermal zone fields directly (Daniel
Lezcano)
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano)
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui)
- Add more thermal zone device encapsulation: prevent setting
structure field directly, access the sensor device instead the
thermal zone's device for trace, relocate the traces in
drivers/thermal (Daniel Lezcano)
- Use the generic trip point for the i.MX and remove the
get_trip_temp ops (Daniel Lezcano)
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li)
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown
(Wolfram Sang)
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur)
- Add MT8365 support (Amjad Ouled-Ameur)
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel)
- Add driver support for RK3588 (Finley Xiao)
- Use devm_reset_control_array_get_exclusive() for the Rockchip
driver (Ye Xingchen)
- Detect power gated thermal zones and return -EAGAIN when reading
the temperature (Mikko Perttunen)
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring)
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn)
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai)
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen)
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI)
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano)
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano)
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano)
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui)
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki)
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring)
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki)
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada)"
* tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: intel: int340x: Add DLVR support for RFIM control
thermal/core: Alloc-copy-free the thermal zone parameters structure
thermal/of: Unexport unused OF functions
thermal/drivers/bcm2835: Remove buggy call to thermal_of_zone_unregister
thermal/drivers/mediatek/lvts_thermal: Add AP domain for mt8195
dt-bindings: thermal: mediatek: Add AP domain to LVTS thermal controllers for mt8195
thermal: amlogic: Use dev_err_probe()
thermal/drivers/mediatek/lvts_thermal: Fix sensor 1 interrupt status bitmask
MAINTAINERS: adjust entry in THERMAL/POWER_ALLOCATOR after header movement
dt-bindings: thermal: Drop unneeded quotes
thermal/core: Remove thermal_bind_params structure
thermal/drivers/tegra-bpmp: Handle offline zones
thermal/drivers/rockchip: use devm_reset_control_array_get_exclusive()
dt-bindings: rockchip-thermal: Support the RK3588 SoC compatible
thermal/drivers/rockchip: Support RK3588 SoC in the thermal driver
thermal/drivers/rockchip: Support dynamic sized sensor array
thermal/drivers/rockchip: Simplify channel id logic
thermal/drivers/rockchip: Use dev_err_probe
thermal/drivers/rockchip: Simplify clock logic
thermal/drivers/rockchip: Simplify getting match data
...
Merge ACPI bus type driver changes, ACPI backlight driver updates and a
series of cleanups related to of.h for 6.4-rc1:
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki).
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede).
- Replace irqdomain.h include with struct declarations in ACPI headers
and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring).
* acpi-bus:
ACPI: bus: Ensure that notify handlers are not running after removal
ACPI: bus: Add missing braces to acpi_sb_notify()
* acpi-video:
ACPI: video: Remove desktops without backlight DMI quirks
ACPI: video: Remove register_backlight_delay module option and code
* acpi-misc:
ACPI: Replace irqdomain.h include with struct declarations
fpga: lattice-sysconfig-spi: Add explicit include for of.h
tpm: atmel: Add explicit include for of.h
virtio-mmio: Add explicit include for of.h
pata: ixp4xx: Add explicit include for of.h
ata: pata_macio: Add explicit include of irqdomain.h
serial: 8250_tegra: Add explicit include for of.h
net: rfkill-gpio: Add explicit include for of.h
staging: iio: resolver: ad2s1210: Add explicit include for of.h
iio: adc: ad7292: Add explicit include for of.h
The event config is controlled through the IIO events subsystem and
device wakeup is controlled by /sys/devices/.../power/wakeup. Let's keep
those two knobs independent.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-10-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The palmas gpadc block has support for monitoring up to 2 ADC channels
and issue an interrupt if they reach past a set threshold. This change
hooks into the IIO events system and exposes to userspace the ability to
configure these threshold values for each channel, but only allow up to
2 such thresholds to be enabled at any given time. Trying to enable a
third channel will result in an error.
Userspace is expected to input calibrated, as opposed to raw, values as
threshold. However, it is not enough to do the opposite of what is done
when converting the other way around. To account for tolerances in the
ADC, the calculated raw threshold should be adjusted based on the ADC
specifications for the device. These specifications include the integral
nonlinearity (INL), offset, and gain error. To adjust the high
threshold, use the following equation:
(calibrated value + INL) * Gain error + offset = maximum value [1]
Likewise, use the following equation for the low threshold:
(calibrated value - INL) * Gain error - offset = minimum value
The gain error is a combination of gain error, as listed in the
datasheet, and gain error drift due to temperature and supply. The exact
values for these specifications vary between palmas devices. This patch
sets the values found in TWL6035, TWL6037 datasheet.
[1] TI Application Report, SLIA087A, Guide to Using the GPADC in
TPS65903x, TPS65917-Q1, TPS65919-Q1, and TPS65916 Devices.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-9-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of having high_threshold > 0 as an indicator for upper threshold
event and lower threshold event otherwise, use enum iio_event_direction
instead. This is hopefully less ambiguous.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-6-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The palmas gpadc block has support for monitoring up to 2 ADC channels
and issue an interrupt if they reach past a set threshold. This is
currently used to wake up the system from sleep, but the functionality
is more generic than that. As such, change the naming of functions and
variables to refer to it as events instead, except during suspend and
resume where wakeup still make sense.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-5-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It does not seem to be used by anyone and later patches in this series
are made simpler by first removing this. There is now a lot of dead code
that cannot be reached, until later patches revive it. Arguably, this is
preferred over removing the code only to add it again.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-4-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DSDT ROTM method seen in the wild with SMO8B30 _HID.
Making assumption it is similar to that used for bmc150 plus
information from Darrell that the rotation is out by 90 degrees at boot.
Method (ROTM, 0, NotSerialized)
{
Name (RBUF, Package (0x03)
{
"0 -1 0",
"1 0 0",
"0 0 1"
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_.ROTM.RBUF */
}
Reported-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Darrell Kavanagh <darrell.kavanagh@gmail.org>
Link: https://lore.kernel.org/r/20230130201018.981024-3-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ID seen in the wild and it is a valid ST micro ID.
An offset of 1 for the device ID enum is needed when adding support for
retrieving the ID from device_get_match_data() to allow detection of
NULL pointer and fallback to i2c_device_id table.
DSDT chunk cropped for relevant parts.
Scope (_SB.PCI0.I2C5)
{
Device (DEV)
{
Name (_HID, EisaId ("SMO8B30")) // _HID: Hardware ID
Name (_CID, EisaId ("SMO8B30")) // _CID: Compatible ID
Name (_UID, Zero) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x006A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C5",
0x00, ResourceConsumer, , Exclusive,
)
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_._CRS.RBUF */
}
Method (ROTM, 0, NotSerialized)
{
Name (RBUF, Package (0x03)
{
"0 -1 0",
"1 0 0",
"0 0 1"
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_.ROTM.RBUF */
}
...
Link: https://lore.kernel.org/all/20230129182441.082f29d0@jic23-huawei/
Reported-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Tested-by: Darrell Kavanagh <darrell.kavanagh@gmail.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230130201018.981024-2-jic23@kernel.org
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
-----BEGIN PGP SIGNATURE-----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=xxs6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanups for the 6.4 cycle.
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
* tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (63 commits)
MAINTAINERS: Add ROHM BU27034
iio: light: ROHM BU27034 Ambient Light Sensor
dt-bindings: iio: light: Support ROHM BU27034
MAINTAINERS: Add IIO gain-time-scale helpers
iio: light: Add gain-time-scale helpers
doc: Make sysfs-bus-iio doc more exact
iio: dac: set variable max5522_channels storage-class-specifier to static
dt-bindings: iio: temperature: ltc2983: Make 'adi,custom-thermocouple' signed
dt-bindings: iio: temperature: ltc2983: Fix child node unevaluated properties
iio: addac: stx104: Use regmap_read_poll_timeout() for conversion poll
iio: addac: stx104: Migrate to the regmap API
iio: addac: stx104: Improve indentation in stx104_write_raw()
iio: addac: stx104: Use define rather than hardcoded limit for write val
iio: addac: stx104: Fix race condition when converting analog-to-digital
iio: addac: stx104: Fix race condition for stx104_write_raw()
dt-bindings: iio: st-sensors: Fix repeated text
staging: iio: resolver: ads1210: fix config mode
iio: adc: ti-ads1100: fix error code in probe()
iio: accel: add support for IIS328DQ variant
dt-bindings: iio: st-sensors: Add IIS328DQ accelerometer
...
ROHM BU27034 is an ambient light sensor with 3 channels and 3 photo diodes
capable of detecting a very wide range of illuminance. Typical application
is adjusting LCD and backlight power of TVs and mobile phones.
Add initial support for the ROHM BU27034 ambient light sensor.
NOTE:
- Driver exposes 4 channels. One IIO_LIGHT channel providing the
calculated lux values based on measured data from diodes #0 and
#1. In addition, 3 IIO_INTENSITY channels are emitting the raw
register data from all diodes for more intense user-space
computations.
- Sensor has GAIN values that can be adjusted from 1x to 4096x.
- Sensor has adjustible measurement times of 5, 55, 100, 200 and
400 mS. Driver does not support 5 mS which has special
limitations.
- Driver exposes standard 'scale' adjustment which is
implemented by:
1) Trying to adjust only the GAIN
2) If GAIN adjustment alone can't provide requested
scale, adjusting both the time and the gain is
attempted.
- Driver exposes writable INT_TIME property that can be used
for adjusting the measurement time. Time adjustment will also
cause the driver to try to adjust the GAIN so that the
overall scale is kept as close to the original as possible.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/2a7efb6f335da5526fbe34b95137c5e45db5c5d3.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some light sensors can adjust both the HW-gain and integration time.
There are cases where adjusting the integration time has similar impact
to the scale of the reported values as gain setting has.
IIO users do typically expect to handle scale by a single writable 'scale'
entry. Driver should then adjust the gain/time accordingly.
It however is difficult for a driver to know whether it should change
gain or integration time to meet the requested scale. Usually it is
preferred to have longer integration time which usually improves
accuracy, but there may be use-cases where long measurement times can be
an issue. Thus it can be preferable to allow also changing the
integration time - but mitigate the scale impact by also changing the gain
underneath. Eg, if integration time change doubles the measured values,
the driver can reduce the HW-gain to half.
The theory of the computations of gain-time-scale is simple. However,
some people (undersigned) got that implemented wrong for more than once.
Add some gain-time-scale helpers in order to not dublicate errors in all
drivers needing these computations.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/268d418e7cffcdaa2ece6738478bbc57692c213e.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
smatch reports
drivers/iio/dac/max5522.c:55:28: warning: symbol
'max5522_channels' was not declared. Should it be static?
This variable is only used in one file so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230404013828.1914523-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC sample captures take a certain amount of time to complete after
initiated; this conversion time range can be anywhere from 5
microseconds to 53.68 seconds depending on the configuration of the
Analog Input Frame Timer register. When the conversion is in progress,
the ADC Status register CNV bit is high. Call regmap_read_poll_timeout()
to poll until the ADC conversion is completed (or timeout if more than
53.68 seconds passes).
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/9ef433f107afd1d4dcd2d97ef0e932d7045c2bbd.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
In addition, to improve code organization in stx104_probe(), the
devm_iio_device_register() call is moved above GPIO configuration in
order to keep relevant code closer together.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/0bcdfc4738cc019fb2ff83f61eb46a3488bc166d.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
By bailing out early if chan->output is false for the IIO_CHAN_INFO_RAW,
indentation can be decreased by a tab and code readability improved.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/487d17da9e2612f3e6b2bd1c3def2fa1b955db9b.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DAC register is 16 bits wide, so the value passed by write_raw()
should be checked against that limit. Rather than hardcoding the 16-bit
maximum value limit, use a define to improve readability and make the
intention of the code clearer. The explicit cast is also avoided by
instead explicitly checking for negative values.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/4c9f4f1b4a270d133be70c82a091351b531b5e3e.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC conversion procedure requires several device I/O operations
performed in a particular sequence. If stx104_read_raw() is called
concurrently, the ADC conversion procedure could be clobbered. Prevent
such a race condition by utilizing a mutex.
Fixes: 4075a283ae ("iio: stx104: Add IIO support for the ADC channels")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/2ae5e40eed5006ca735e4c12181a9ff5ced65547.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The priv->chan_out_states array and actual DAC value can become
mismatched if stx104_write_raw() is called concurrently. Prevent such a
race condition by utilizing a mutex.
Fixes: 97a445dad3 ("iio: Add IIO support for the DAC on the Apex Embedded Systems STX104")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/c95c9a77fcef36b2a052282146950f23bbc1ebdc.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This code has a copy and paste bug so it accidentally returns
"PTR_ERR(data->reg_vdd)" which is a valid pointer cast to int. It
should return "ret" instead.
Fixes: 541880542f ("iio: adc: Add TI ADS1100 and ADS1000")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/36fa2aeb-f392-4793-8b38-ae15514033c8@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tsl2772_read_prox_diodes() will correctly parse the properties from
device tree to determine which proximity diode(s) to read from, however
it didn't actually set this value on the struct tsl2772_settings. Let's
go ahead and fix that.
Reported-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/lkml/20230327120823.1369700-1-trix@redhat.com/
Fixes: 94cd1113aa ("iio: tsl2772: add support for reading proximity led settings from device tree")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20230404011455.339454-1-bmasney@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With linux/acpi.h no longer implicitly including of.h, add an explicit
include of of.h to fix the following error:
drivers/iio/adc/ad7292.c:307:9: error: implicit declaration of function 'for_each_available_child_of_node'; did you mean 'fwnode_for_each_available_child_node'? [-Werror=implicit-function-declaration]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In ad5755_parse_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 3ac27afefd ("iio:dac:ad5755: Switch to generic firmware properties and drop pdata")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20230322035627.1856421-1-windhl@126.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The at91_adc_allocate_trigger() function is supposed to return error
pointers. Returning a NULL will cause an Oops.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/5d728f9d-31d1-410d-a0b3-df6a63a2c8ba@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mixed bag:
- core - output buffers
Fix return of bytes written when only some succeed.
Fix O_NONBLOCK handling to not block.
- adi,ad7791
Fix IRQ type. Not confirmed to have any impact but good to correct it anyway
- adi,adis16400
Missing CONFIG_CRC32
- capella,cm32181
Unregister 2nd I2C client if one is used.
- cio-dac
Fix bitdepth for range check on write.
- linear,ltc2497
Fix a wrong shift of the LSB introduced when switching to be24 handling.
- maxim,max11410
Fix handling of return code in read_poll_timeout()
- qcom,spmi-adc
Fix an accidental change of channel name to include the reg value from OF.
- ti,palmas
Fix a null dereference on remove due to wrong function used to get the
drvdata.
- ti,ads7950
Mark GPIO as can sleep.
-----BEGIN PGP SIGNATURE-----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=8wF1
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-6.3a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
1st set of IIO fixes for 6.3
Usual mixed bag:
- core - output buffers
Fix return of bytes written when only some succeed.
Fix O_NONBLOCK handling to not block.
- adi,ad7791
Fix IRQ type. Not confirmed to have any impact but good to correct it anyway
- adi,adis16400
Missing CONFIG_CRC32
- capella,cm32181
Unregister 2nd I2C client if one is used.
- cio-dac
Fix bitdepth for range check on write.
- linear,ltc2497
Fix a wrong shift of the LSB introduced when switching to be24 handling.
- maxim,max11410
Fix handling of return code in read_poll_timeout()
- qcom,spmi-adc
Fix an accidental change of channel name to include the reg value from OF.
- ti,palmas
Fix a null dereference on remove due to wrong function used to get the
drvdata.
- ti,ads7950
Mark GPIO as can sleep.
* tag 'iio-fixes-for-6.3a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
iio: adc: palmas_gpadc: fix NULL dereference on rmmod
iio: adc: max11410: fix read_poll_timeout() usage
iio: dac: cio-dac: Fix max DAC write value check for 12-bit
iio: light: cm32181: Unregister second I2C client if present
iio: accel: kionix-kx022a: Get the timestamp from the driver's private data in the trigger_handler
iio: adc: ad7791: fix IRQ flags
iio: buffer: make sure O_NONBLOCK is respected
iio: buffer: correctly return bytes written in output buffers
iio: light: vcnl4000: Fix WARN_ON on uninitialized lock
iio: adis16480: select CONFIG_CRC32
drivers: iio: adc: ltc2497: fix LSB shift
iio: adc: qcom-spmi-adc5: Fix the channel name
The <linux/bitops.h> header is included in the stx104 driver so that we
can use the BIT() macro. This macro is actually defined in the
<linux/bits.h> header, so replace the <linux/bitops.h> header inclusion
with <linux/bits.h>.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230318185503.341914-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
Includes trivial header inclusion tidy up.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311140218.74920-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ads7950 uses a mutex as well as SPI transfers in its GPIO callbacks.
This means these callbacks can sleep and the `can_sleep` flag should be
set.
Having the flag set will make sure that warnings are generated when calling
any of the callbacks from a potentially non-sleeping context.
Fixes: c97dce792d ("iio: adc: ti-ads7950: add GPIO support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20230312210933.2275376-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
To retain ordering move the request to a place that is executed later.
This way the time of enable keeps the same.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230313185333.2776785-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Calling dev_to_iio_dev() on a platform device pointer is undefined and
will make adc NULL.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230313205029.1881745-1-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
From the comment of platform_get_irq(), it only returns non-zero IRQ
number and negative error number, other than zero.
Fix this by removing the if condition.
Signed-off-by: Cheng Ziqiu <chengziqiu@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230314070130.60581-1-chengziqiu@hust.edu.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The left side of the loop condition never becomes false. hwchan cannot be
NULL, because it points to elements of the hw_channels array that takes
one of 4 predefined values: pm8018_xoadc_channels, pm8038_xoadc_channels,
pm8058_xoadc_channels, pm8921_xoadc_channels.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kasumov Ruslan <s02210418@gse.cs.msu.ru>
Link: https://lore.kernel.org/r/20230315135114.22684-1-xhxgldhlpfy@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
smatch reports several warnings
drivers/iio/adc/stm32-adc.c:2591:20: warning:
symbol 'stm32_adc_min_ts_h7' was not declared. Should it be static?
drivers/iio/adc/stm32-adc.c:2610:20: warning:
symbol 'stm32_adc_min_ts_mp1' was not declared. Should it be static?
drivers/iio/adc/stm32-adc.c:2630:20: warning:
symbol 'stm32_adc_min_ts_mp13' was not declared. Should it be static?
These variables are only used in stm32-adc.c, so they should be static
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230312161733.470617-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Always reference acpi_device_id and of_device_id tables, as they is
little benefit of conditional compiling and OF table could be used also
for ACPI matching via PRP0001. This fixes warning:
drivers/iio/proximity/sx9500.c:1039:34: error: ‘sx9500_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312153429.371702-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver currently matches only via i2c_device_id, but also has
of_device_id table:
drivers/iio/light/max44009.c:545:34: error: ‘max44009_of_match’ defined but not used [-Werror=unused-const-variable=]
Fixes: 6aef699a7d ("iio: light: add driver for MAX44009")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312153429.371702-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver handles CH_FUNC_CURRENT_INPUT_LOOP_POWER and
CH_FUNC_CURRENT_INPUT_EXT_POWER completely identically. But that's not
correct. In order for CH_FUNC_CURRENT_INPUT_LOOP_POWER to work, two
changes must be made:
(1) expose access to the DAC_CODE_x register so that the intended
output current can be set, i.e. expose the channel as both current
output and current input, and
(2) per the data sheet
When selecting the current input loop powered function, tie the
VIOUTN_x pin to ground via the on-chip 200 kΩ resistor by enabling
the CH_200K_TO_GND bit in the ADC_CONFIGx registers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230301115511.849418-1-linux@rasmusvillemoes.dk
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the value specified in the channel configuration node to populate
the DIN_SINK field of the DIN_CONFIGx register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230306094301.1357543-3-linux@rasmusvillemoes.dk
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Even though we are passing 'ret' as stop condition for
read_poll_timeout(), that return code is still being ignored. The reason
is that the poll will stop if the passed condition is true which will
happen if the passed op() returns error. However, read_poll_timeout()
returns 0 if the *complete* condition evaluates to true. Therefore, the
error code returned by op() will be ignored.
To fix this we need to check for both error codes:
* The one returned by read_poll_timeout() which is either 0 or
ETIMEDOUT.
* The one returned by the passed op().
Fixes: a44ef7c460 ("iio: adc: add max11410 adc driver")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Link: https://lore.kernel.org/r/20230307095303.713251-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1100 is a 16-bit ADC (at 8 samples per second).
The ADS1000 is similar, but has a fixed data rate.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230307065535.7927-2-mike.looijmans@topic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The CIO-DAC series of devices only supports DAC values up to 12-bit
rather than 16-bit. Trying to write a 16-bit value results in only the
lower 12 bits affecting the DAC output which is not what the user
expects. Instead, adjust the DAC write value check to reject values
larger than 12-bit so that they fail explicitly as invalid for the user.
Fixes: 3b8df5fd52 ("iio: Add IIO support for the Measurement Computing CIO-DAC family")
Cc: stable@vger.kernel.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311002248.8548-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230310173217.3429788-4-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/iio/adc/rcar-gyroadc.c:286:34: error: ‘rcar_gyroadc_child_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230311111457.251475-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TMP116 is the predecessor of the TMP117. The TMP116 don't support
custom offset calibration data, instead this register is used as generic
EEPROM storage as well.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230228090518.529811-5-m.felsch@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't error if the device-id found don't match the device-id for the
TMP117 sensor since other TMPxxx might be compatible to the TMP117. The
fallback mechanism tries to gather the required information from the
of_device_id or from the i2c_client information.
The commit also prepares the driver for adding new devices more easily
by making use of switch-case at the relevant parts.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230228090518.529811-3-m.felsch@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the kernel-doc of the function to industrialio-trigger.c
Add a note on the context where the function is expected to be called.
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/bd84fc17e9d22eab998bf48720297f9a77689f45.1677761379.git.mehdi.djait.k@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
During digital filters settling time the driver is expected to drop
samples since they can be corrupted. Introduce the capability to drop
a given number of samples according to the configured ODR.
Add sample_to_discard for LSM6DSM-like sensors since new generation
devices (e.g. LSM6DSO) support DRDY mask where corrupted samples are
masked in hw with values greather than 0x7ffd so the driver can easily
discard them.
I have not added sample_to_discard support for LSM6DS3 or LSM6DS3H since
I do not have any sample for testing at the moment.
Reported-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/21dcd94935c147ef9b1da4984b3da6264ee9609e.1677496295.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Newer models do not require read the calibration parameters and apply the
compensation algorithms in the sensor.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/bb1b95ab3f4e71d3c76543370325c5c9aaa07add.1676823250.git.ang.iglesiasg@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor driver I2C and SPI implementations using pointers for each
variant's chip_info as the driver data. Adds the regmap configuration
to the chip_info struct.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/a48cfa756be48d61dbf656c65daff6e9a1290e6f.1676823250.git.ang.iglesiasg@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
meson_sar_adc_lock() might return an error if BL30 doesn't release its
lock on the hardware. Just returning early from .remove() is wrong
however as this keeps the clocks and regulators on which is never
cleaned up later.
Given the BL30 not giving up its lock is a strong hint for broken
behaviour, and there is nothing we can do about that: Just clean up
ignoring the fact that we're not holding the lock.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230219204439.1641640-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adc_en2 flag is essentially specific to axp20x-compatible devices
because it hardcodes register values. Replace it with a mask field
so the register value can be specified in device match data.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20230217153404.32481-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The code may be clearer if parameters are not re-purposed to hold
temporary results like register values, so introduce local variables
as necessary to avoid that. Regroup macros based on chip type, and
use the FIELD_PREP() macro instead of a hand-rolled version.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20230217153404.32481-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The minimal advised lower rate for adis16475 compatible devices is
1900HZ and not 4000HZ. Set that right in the comments so that it does
not generate any confusion.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230213153208.1027602-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Older firmwares still send sensor configuration using a list of
registers with opaque values defined during sensor tuning.
sx9234 and sx9360 sensor on ACPI based devices are concerned.
More schema to configure the sensors will be needed to support devices
designed for windows, like Samsung Galaxy Book2.
Support schema is: "<_HID>.<register_name>". For instance
"STH9324,reg_adv_ctrl2" in:
Scope (\_SB.PCI0.I2C2)
{
Device (SX28)
{
Name (_HID, "STH9324") // _HID: Hardware ID
...
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /*
Device Properties for _DSD */,
Package (0x3F)
{
...
Package (0x02)
{
"STH9324,reg_adv_ctrl2",
Zero
},`
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230211002421.3447060-1-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct sx_common_data doesn't have a num_default_regs element so
drop the documentation for it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230114172928.80414-1-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add array of explicit gpio names for the `gpiochip` structure of
ad5592r, mainly for debug purposes.
Since the gpios are configurable via the dts, generic names are
used.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20221117090130.51702-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's easier to see the (lack of) difference between the lines when they
are visually aligned.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20230129132020.1352368-1-j.neuschaefer@gmx.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> #mlxsw
Acked-by: Gregory Greenman <gregory.greenman@intel.com> #iwlwifi
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> #power_supply
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> #ahci
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a second dummy client that talks to the actual I2C address was
created in probe(), there should be a proper cleanup on driver and
device removal to avoid leakage.
So unregister the dummy client via another callback.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: c1e62062ff ("iio: light: cm32181: Handle CM3218 ACPI devices with 2 I2C resources")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2152281
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20230223020059.2013993-1-kai.heng.feng@canonical.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the large set of driver changes for char/misc drivers and other
smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem seems
under very active development recently. This required also merging
in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/inQw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksvwCeOvU//SPwrbIpaeHAmHUv0PSVOrwAoKmt4ICh
hQUudlztfkvUJxKIH0gh
=Sjk4
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the large set of driver changes for char/misc drivers and
other smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem
seems under very active development recently. This required also
merging in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the
shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (223 commits)
scripts/tags.sh: fix incompatibility with PCRE2
firmware: coreboot: Remove GOOGLE_COREBOOT_TABLE_ACPI/OF Kconfig entries
mei: lower the log level for non-fatal failed messages
mei: bus: disallow driver match while dismantling device
misc: vmw_balloon: fix memory leak with using debugfs_lookup()
nvmem: stm32: fix OPTEE dependency
dt-bindings: nvmem: qfprom: add IPQ8074 compatible
nvmem: qcom-spmi-sdam: register at device init time
nvmem: rave-sp-eeprm: fix kernel-doc bad line warning
nvmem: stm32: detect bsec pta presence for STM32MP15x
nvmem: stm32: add OP-TEE support for STM32MP13x
nvmem: core: use nvmem_add_one_cell() in nvmem_add_cells_from_of()
nvmem: core: add nvmem_add_one_cell()
nvmem: core: drop the removal of the cells in nvmem_add_cells()
nvmem: core: move struct nvmem_cell_info to nvmem-provider.h
nvmem: core: add an index parameter to the cell
of: property: add #nvmem-cell-cells property
of: property: make #.*-cells optional for simple props
of: base: add of_parse_phandle_with_optional_args()
net: add helper eth_addr_add()
...
-----BEGIN PGP SIGNATURE-----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=cBvC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023022201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- HID-BPF infrastructure: this allows to start using HID-BPF. Note that
the mechanism to ship HID-BPF program through the kernel tree is
still not implemented yet (but is planned).
This should be a no-op for 99% of users. Also we are gaining
kselftests for the HID tree (Benjamin Tissoires)
- Some UAF fixes in workers when using uhid (Pietro Borrello & Benjamin
Tissoires)
- Constify hid_ll_driver (Thomas Weißschuh)
- Allow more custom IIO sensors through HID (Philipp Jungkamp)
- Logitech HID++ fixes for scroll wheel, protocol and debug (Bastien
Nocera)
- Some new device support: Steam Deck (Vicki Pfau), UClogic (José
Expósito), Logitech G923 Xbox Edition steering wheel (Walt Holman),
EVision keyboards (Philippe Valembois)
- other assorted code cleanups and fixes
* tag 'for-linus-2023022201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (99 commits)
HID: mcp-2221: prevent UAF in delayed work
hid: bigben_probe(): validate report count
HID: asus: use spinlock to safely schedule workers
HID: asus: use spinlock to protect concurrent accesses
HID: bigben: use spinlock to safely schedule workers
HID: bigben_worker() remove unneeded check on report_field
HID: bigben: use spinlock to protect concurrent accesses
HID: logitech-hidpp: Add myself to authors
HID: logitech-hidpp: Retry commands when device is busy
HID: logitech-hidpp: Add more debug statements
HID: Add support for Logitech G923 Xbox Edition steering wheel
HID: logitech-hidpp: Add Signature M650
HID: logitech-hidpp: Remove HIDPP_QUIRK_NO_HIDINPUT quirk
HID: logitech-hidpp: Don't restart communication if not necessary
HID: logitech-hidpp: Add constants for HID++ 2.0 error codes
Revert "HID: logitech-hidpp: add a module parameter to keep firmware gestures"
HID: logitech-hidpp: Hard-code HID++ 1.0 fast scroll support
HID: i2c-hid: goodix: Add mainboard-vddio-supply
dt-bindings: HID: i2c-hid: goodix: Add mainboard-vddio-supply
HID: i2c-hid: goodix: Stop tying the reset line to the regulator
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
The trigger_handler gets called from the IRQ thread handler using
iio_trigger_poll_chained() which will only call the bottom half of the
pollfunc and therefore pf->timestamp will not get set.
Use instead the timestamp from the driver's private data which is always
set in the IRQ handler.
Fixes: 7c1d1677b3 ("iio: accel: Support Kionix/ROHM KX022A accelerometer")
Link: https://lore.kernel.org/linux-iio/Y+6QoBLh1k82cJVN@carbian/
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Link: https://lore.kernel.org/r/20230218135111.90061-1-mehdi.djait.k@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupt is triggered on the falling edge rather than being a level
low interrupt.
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230120124645.819910-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For output buffers, there's no guarantee that the buffer won't be full
in the first iteration of the loop in which case we would block
independently of userspace passing O_NONBLOCK or not. Fix it by always
checking the flag before going to sleep.
While at it (and as it's a bit related), refactored the loop so that the
stop condition is 'written != n', i.e, run the loop until all data has
been copied into the IIO buffers. This makes the code a bit simpler.
Fixes: 9eeee3b0bf ("iio: Add output buffer support")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230216101452.591805-3-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If for some reason 'rb->access->write()' does not write the full
requested data and the O_NONBLOCK is set, we would return 'n' to
userspace which is not really truth. Hence, let's return the number of
bytes we effectively wrote.
Fixes: 9eeee3b0bf ("iio: Add output buffer support")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230216101452.591805-2-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmPgG/geHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGidAH/j0pUbmniNM3aft8
5O1XxltlOZgqxju8OQhkiuX9VnQuuSeTNhAuj6jfcQOLpXDvlKsVfrpBxEfXalML
yead9QAy/OT3hNGQxifMQzGbsmaWH1kgxxnv2lKo2eNP5KYZ+rec+IgtQhgX9quN
q/N/ymd2/ju9AEOVRYwG1PD1EiIwTd3xPfBZl4Z35J+Ym+6NRrlXmN6J9LwslXmJ
/P4cwgdf9/TuYAB96EshRHsZ4Tk/Gxkn15uyhLaWBmrZ/LAF5JGbClEfFlCWgjwv
F5SGv3F+O6HSv49W9a24XtenE+3tw78AbCdqKZyzbb2whhv1eY99vKSbGnCahc/y
O0VBP/g=
=YoPk
-----END PGP SIGNATURE-----
Merge 6.2-rc7 into char-misc-next
We need the char-misc driver fixes in here as other patches depend on
them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are different init functions for the sensors in this driver in
which only one initializes the generic vcnl4000_lock. With commit
e21b5b1f26 ("iio: light: vcnl4000: Preserve conf bits when toggle power")
the vcnl4040 sensor started to depend on the lock, but it was missed to
initialize it in vcnl4040's init function. This has not been visible
until we run lockdep on it:
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
at kernel/locking/mutex.c:575 __mutex_lock+0x4f8/0x890
Call trace:
__mutex_lock
mutex_lock_nested
vcnl4200_set_power_state
vcnl4200_init
vcnl4000_probe
Fix this by initializing the lock in the probe function instead of doing
it in the chip specific init functions.
Fixes: e21b5b1f26 ("iio: light: vcnl4000: Preserve conf bits when toggle power")
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230131140109.2067577-1-marten.lindahl@axis.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added extra spaces before statements to fix
following indentation warnings reported by checkpatch.pl.
WARNING: Statements should start on a tabstop
+ return 0;
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Link: https://lore.kernel.org/r/Y9Vf4Tp8JKvy+y0u@yoga
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Correct the "sub_lsb" shift for the ltc2497 and drop the sub_lsb element
which is now constant.
An earlier version of the code shifted by 14 but this was a consequence
of reading three bytes into a __be32 buffer and using be32_to_cpu(), so
eight extra bits needed to be skipped. Now we use get_unaligned_be24()
and thus the additional skip is wrong.
Fixes: 2187cfeb36 ("drivers: iio: adc: ltc2497: LTC2499 support")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Link: https://lore.kernel.org/r/20230127125714.44608-1-ian.ray@ge.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Smatch Warns:
drivers/iio/accel/mma9551_core.c:299
mma9551_read_config_word() error: uninitialized symbol 'v'.
When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.
Note: No actual bug as caller checks the return value and does not
use the parameter in the problem case.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126153610.3586243-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Smatch Warns: drivers/iio/accel/mma9551_core.c:357
mma9551_read_status_word() error: uninitialized symbol 'v'.
When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.
Note: Not a bug as such because the caller checks return value and
doesn't not use this parameter in the problem case.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126152147.3585874-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
checkpatch reports
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
FILE: drivers/iio/imu/bno055/bno055_ser_trace.c:1:
+//SPDX-License-Identifier: GPL-2.0
Add a space
Fixes: 2eef5a9cc6 ("iio: imu: add BNO055 serdev driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230124194301.656518-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The node name can contain an address part which is unused
by the driver. Moreover, this string is propagated into
the userspace label, sysfs filenames *and breaking ABI*.
Cut the address part out before assigning the channel name.
Fixes: 4f47a236a2 ("iio: adc: qcom-spmi-adc5: convert to device properties")
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230118100623.42255-1-andriy.shevchenko@linux.intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC in i.mx93 is a total new ADC IP, add a driver to support
this ADC.
Currently, only support one shot normal conversion triggered by
software. For other mode, will add in future.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230117135137.1735536-2-haibo.chen@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need the name 'st_lsm6dsx_ext_info' for the actual 'iio_chan_spec_ext_info'.
Rename the 'st_lsm6dsx_ext_info' in st_lsm6dsx_shub.c to 'st_lsm6dsx_shub_info'.
For consistency, replace also 'ext' by 'shub' in 'st_lsm6dsx_ext_attributes'
and 'st_lsm6dsx_ext_attribute_group'.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/1673874434-30750-2-git-send-email-Philippe.DeMuyter@macq.eu
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700_CTRL_ODR_MIN is not used but value is probably wrong.
Remove it for a good readability.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The absence of correct offset leads a failed initialization ODR mode
assignment.
Select MAX ODR mode as the initialization ODR mode by field mask and
FIELD_PREP.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The absence of a correct offset leads an incorrect ODR mode
readback after use a hexadecimal number to mark the value from
FXOS8700_CTRL_REG1.
Get ODR mode by field mask and FIELD_GET clearly and conveniently.
And attach other additional fix for keeping the original code logic
and a good readability.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to configure proximity sensor interrupts and threshold
limits for vcnl4040. If an interrupt is detected an event will be
pushed to the event interface.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230117190017.3789181-4-marten.lindahl@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports 4 chips, by which only one (vcnl4010) handles
interrupts and has support for triggered buffer. The setup of these
functions is hardcoded for vcnl4010 inside the generic vcnl4000_probe,
and thus ignores the chip specific configuration structure where all
other chip specific functions are specified.
This complicates adding interrupt handler and triggered buffer support
to chips which may have support for it.
Add members for irq threads and iio_buffer_setup_ops to the generic
vcnl4000_chip_spec struct, so that instead of checking a chip specific
boolean irq support, we check for a chip specific triggered buffer
handler, and/or a chip specific irq thread handler.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230117190017.3789181-3-marten.lindahl@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to allow the chip_spec array reference the function pointers
for interrupts, the code for these functions need to be moved above the
chip_spec array.
This is a prestep to support a more generic setup of interrupts.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230117190017.3789181-2-marten.lindahl@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for DAC max5522.
Tested writing DAC A and B with some values,
from 0 to 1023, measured output voltages, driver works properly.
Additions for max5523/24/25 will follow.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20221106165928.223318-1-angelo.dureghello@timesys.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit c1e62062ff ("iio: light: cm32181: Handle CM3218 ACPI devices
with 2 I2C resources") creates a second client for the actual I2C
address, but the "struct device" passed to PM ops is the first I2C
client that can't talk to the sensor.
That means the I2C transfers in both suspend and resume routines can
fail and blocking the whole suspend process.
Instead of using the first client for I2C transfer, use the I2C client
stored in the cm32181 private struct so the PM ops can get the correct
I2C client to really talk to the sensor device.
Fixes: 68c1b3dd5c ("iio: light: cm32181: Add PM support")
BugLink: https://bugs.launchpad.net/bugs/1988346
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2152281
Tested-by: Wahaj <wahajaved@protonmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230118170422.339619-1-kai.heng.feng@canonical.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the current users is using gaps in the list of the items.
No need to have a specific function for that, just replace it by
library available __sysfs_match_string().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230118074828.66155-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace open coded fwnode_device_is_compatible() in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119174749.76769-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Return value should be zero for success. This was forgotten for timestamp
feature. Verified on RealSense cameras.
Fixes: 4648cbd8fb ("iio: hid-sensor-gyro-3d: Add timestamp channel")
Signed-off-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Link: https://lore.kernel.org/r/7c1809dc74eb2f58a20595f4d02e76934f8e9219.camel@intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Return value should be zero for success. This was forgotten for timestamp
feature. Verified on RealSense cameras.
Fixes: a96cd0f901 ("iio: accel: hid-sensor-accel-3d: Add timestamp")
Signed-off-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Link: https://lore.kernel.org/r/a6dc426498221c81fa71045b41adf782ebd42136.camel@intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230113141117.23353-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of identification registers to STM32 DFSDM
to allow hardware capabilities discovery and configuration check.
The number of filters and channels, are read from registers,
when they are available.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20230105125331.328275-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The magnetometer part of ST LSM303C is similar (perhaps even identical)
to the already supported standalone LIS3MDL magnetometer, so just
add the new st,lsm303c-magn compatible for the existing definitions.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230106102239.9647-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The accelerometer part of ST LSM303C is similar (perhaps even identical)
to the already supported standalone LIS2HH12 accelerometer, so just
add the new st,lsm303c-accel compatible for the existing definitions.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230106102239.9647-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The following kernel linkage error:
st_lsm6dsx_core.o: in function `st_lsm6dsx_sw_buffers_setup':
st_lsm6dsx_core.c:2578: undefined reference to `devm_iio_triggered_buffer_setup_ext'
is caused by the fact that the object owning devm_iio_triggered_buffer_setup_ext()
(drivers/iio/buffer/industrialio-triggered-buffer.o) is allowed to be
built as module when its user (drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c)
is built-in.
The st_lsm6dsx driver already has a "select IIO_BUFFER", so add another
select for IIO_TRIGGERED_BUFFER, to make that option follow what is set
for the st_lsm6dsx driver. This is similar to what other iio drivers do.
Fixes: 2cfb2180c3 ("iio: imu: st_lsm6dsx: introduce sw trigger support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230103130348.1733467-1-vladimir.oltean@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no point to specify asm-generic for the unaligned.h.
Drop the 'generic' suffix and move the inclusion to be after
the non-IIO linux/* ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230103144903.39905-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused and code is obfuscated
by ifdeffery.
Drop anti-pattern of ACPI_PTR() use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230102173450.29882-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The spi_get_device_match_data() helps to get driver data from the
firmware node or SPI ID table. Use it instead of open coding.
While at it, switch ID tables to provide an acrual pointers to
the configuration data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230102173450.29882-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is useful to be able to build this driver without needing
to build support for ARCH_EP93XX.
Also add an explicit dependency on HAS_IOMEM so we have
devm_platform_ioremap_resource() etc available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20221231144128.489810-1-jic23@kernel.org
VAC needs to be wired up to produce proper measurements,
without this change only near zero values are reported.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1696f36482 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221217221305.671117-1-andreas@kemnade.info
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When device is in active mode, it fails to set an ACCEL full-scale
range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG. This is not align with the
datasheet, but it is a fxos8700 chip behavior.
Keep the device in standby mode before setting ACCEL full-scale range
into FXOS8700_XYZ_DATA_CFG in chip initialization phase and setting
scale phase.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-6-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The length of ACCEL and MAGN 3-axis channels output data is 6 byte
individually. However block only read 3 bytes data into buffer from
ACCEL or MAGN output data registers every time. It causes an incomplete
ACCEL and MAGN channels readback.
Set correct value count for regmap_bulk_read to get 6 bytes ACCEL and
MAGN channels readback.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Because ACCEL and MAGN channels data register base address is
swapped the accelerometer and magnetometer channels readback is
swapped.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700 is an IMU sensor with ACCEL sensor and MAGN sensor.
Sensor type is indexed by corresponding channel type in a switch.
IIO_ANGL_VEL channel type mapped to MAGN sensor has caused confusion.
Fix the mapping label of "IIO_MAGN" channel type instead of
"IIO_ANGL_VEL" channel type to MAGN sensor.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some inputs need to be wired up to produce proper measurements,
without this change only near zero values are reported.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 1696f36482 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")
Link: https://lore.kernel.org/r/20221201181635.3522962-1-andreas@kemnade.info
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
irq flood happen when run
cat /sys/bus/iio/devices/iio:device0/in_voltage1_raw
imx8qxp_adc_read_raw()
{
...
enable irq
/* adc start */
writel(1, adc->regs + IMX8QXP_ADR_ADC_SWTRIG);
^^^^ trigger irq flood.
wait_for_completion_interruptible_timeout();
readl(adc->regs + IMX8QXP_ADR_ADC_RESFIFO);
^^^^ clear irq here.
...
}
There is only FIFO watermark interrupt at this ADC controller.
IRQ line will be assert until software read data from FIFO.
So IRQ flood happen during wait_for_completion_interruptible_timeout().
Move FIFO read into irq handle to avoid irq flood.
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Cc: stable@vger.kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20221201140110.2653501-1-Frank.Li@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The clang-analyzer reported a warning: "Value stored to 'ret'
is never read".
Fix the return value check if devm_krealloc() fails to resize
ams_channels.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221125113112.219290-1-marpagan@redhat.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
of_get_parent() will return a device_node pointer with refcount
incremented. We need to use of_node_put() on it when done. Add the
missing of_node_put() in the error path of berlin2_adc_probe();
Fixes: 70f1937911 ("iio: adc: add support for Berlin")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221129020316.191731-1-wangxiongfeng2@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When STM32 DFSDM driver is built as module, no modalias information
is available. This prevents module to be loaded by udev.
Add MODULE_DEVICE_TABLE() to fill module aliases.
Fixes: e2e6771c64 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20221202152848.45585-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Much like 807efb7102e8 ("thermal: qcom-spmi-adc-tm5: suppress
probe-deferral error message") the ADC5 driver also spams a similar
probe-deferral error on startup when a channel is not yet available:
[ 0.343136] qcom-spmi-adc-tm5 1c40000.spmi:pmic@0:adc-tm@3500: get dt data failed: -517
Suppress it by using dev_err_probe instead, which also takes care of
storing the message as reason for deferring.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221216190945.902754-1-marijn.suijten@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
PM callbacks take struct device pointer as a parameter, use
dev_get_drvdata() to retrieve it instead of unneeded double
loop of referencing via i2c_get_clientdata(to_i2c_client(dev)).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221207190348.9347-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a temporary variable to keep pointer to struct device.
Utilise it inside the ->probe() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221207190348.9347-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no in-kernel user for legacy platform data.
Otherwise, a new one can use software nodes instead.
Hence, drop legacy platform data code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221207190348.9347-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The CALIB_FRAC() is defined and might had been used in
tsl2563_calib_from_sysfs(). But let's just move a comment
from it to the latter function.
CLAIB_FRAC_HALF is used in a single place, i.e. in
tsl2563_calib_to_sysfs(). So, let's just inline it there.
While at it, switch to use DIV_ROUND_CLOSEST().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221207190348.9347-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce tsl2563_configure_irq() to configure INT in one place.
While at it, make use of TSL2563_INT_LEVEL and newly introduced
TSL2563_INT_MASK.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221207190348.9347-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver already uses the word accessors when it makes sense, but
in the tsl2563_configure(). Switch the latter to use word accessor.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221207190348.9347-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of hardcoding IRQ trigger type to IRQF_TRIGGER_RAISING,
let's respect the settings specified in the firmware description.
To be compatible with the older firmware descriptions, if trigger
type is not set up there, we'll set it to default (raising edge).
Fixes: 388be48839 ("staging:iio: tsl2563 abi fixes and interrupt handling")
Fixes: bdab100173 ("staging:iio:light:tsl2563 remove old style event registration.")
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221207190348.9347-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-133-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the remaining calls in probe() have devm_ equivalents so
switching to those allows the remove() callbacks to be deleted.
No functional change.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Tomasz Duszynski <tduszyns@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20221016163409.320197-15-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver only turns the power on at probe and off at remove.
The new devm_regulator_get_enable() replaces this boilerplate code.
Some additional refactoring to drop now unnecessary unwinding after
this change.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Tomasz Duszynski <tduszyns@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20221016163409.320197-14-jic23@kernel.org
This driver only turns the power on at probe and off via a custom
devm_add_action_or_reset() callback. The new
devm_regulator_bulk_get_enable() replaces this boilerplate code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20221016163409.320197-3-jic23@kernel.org
Replace the open-code with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212011156314630626@zte.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace the open-code with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212011142333790361@zte.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD5337 belongs to the same family as the AD5338.
The difference is that the AD5337 has 8-bit precision instead of 10-bit.
Add support for the AD5337 chip in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221130182632.3856675-2-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TI LMP92064 is a dual 12 Bit ADC connected via SPI.
The two channels are intended for simultaneous measurements of the voltage
across- and current through a load to allow accurate instantaneous power
measurements.
The driver does not yet take advantage of this feature, as buffering is not
yet implemented.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Link: https://lore.kernel.org/r/20221128133503.1355898-2-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for TI TMAG5273 Low-Power Linear 3D Hall-Effect Sensor.
Additionally to temperature and magnetic X, Y and Z-axes the angle and
magnitude are reported.
The sensor is operating in continuous measurement mode and changes to sleep
mode if not used for 5 seconds.
Datasheet: https://www.ti.com/lit/gpn/tmag5273
Signed-off-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221201072220.402585-4-gerald.loacker@wolfvision.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a generic 'hsdev->usage' instead of the HID_USAGE_SENSOR_PROX to
allow this driver to drive the Lenvo custom proximity sensor, which is
registered under a 'custom' usage and not HID_USAGE_SENSOR_PROX.
Add the Lenovo Intelligent Sensing Solution (LISS) human presence sensor
to the platform device ids.
Signed-off-by: Philipp Jungkamp <p.jungkamp@gmx.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use a generic 'hsdev->usage' instead of the HID_USAGE_SENSOR_ALS to
allow this driver to drive the Lenovo custom ambient light sensor,
which is registered under a 'custom' usage and not HID_USAGE_SENSOR_ALS.
Add the Lenovo Intelligent Sensing Solution (LISS) ambient light sensor
to the platform device ids.
Signed-off-by: Philipp Jungkamp <p.jungkamp@gmx.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Here is the large set of char/misc and other driver subsystem changes
for 6.2-rc1. Nothing earth-shattering in here at all, just a lot of new
driver development and minor fixes. Highlights include:
- fastrpc driver updates
- iio new drivers and updates
- habanalabs driver updates for new hardware and features
- slimbus driver updates
- speakup module parameters added to aid in boot time configuration
- i2c probe_new conversions for lots of different drivers
- other small driver fixes and additions
One semi-interesting change in here is the increase of the number of
misc dynamic minors available to 1048448 to handle new huge-cpu systems.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wrdw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykSDgCdHjUHS62/UnKdB9rLtyAOFxS/6DgAn2X4Unf8
RN8Mn2mUIiBzyu5p+Zc7
=tK3S
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc and other driver subsystem changes
for 6.2-rc1. Nothing earth-shattering in here at all, just a lot of
new driver development and minor fixes.
Highlights include:
- fastrpc driver updates
- iio new drivers and updates
- habanalabs driver updates for new hardware and features
- slimbus driver updates
- speakup module parameters added to aid in boot time configuration
- i2c probe_new conversions for lots of different drivers
- other small driver fixes and additions
One semi-interesting change in here is the increase of the number of
misc dynamic minors available to 1048448 to handle new huge-cpu
systems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (521 commits)
extcon: usbc-tusb320: Convert to i2c's .probe_new()
extcon: rt8973: Convert to i2c's .probe_new()
extcon: fsa9480: Convert to i2c's .probe_new()
extcon: max77843: Replace irqchip mask_invert with unmask_base
chardev: fix error handling in cdev_device_add()
mcb: mcb-parse: fix error handing in chameleon_parse_gdd()
drivers: mcb: fix resource leak in mcb_probe()
coresight: etm4x: fix repeated words in comments
coresight: cti: Fix null pointer error on CTI init before ETM
coresight: trbe: remove cpuhp instance node before remove cpuhp state
counter: stm32-lptimer-cnt: fix the check on arr and cmp registers update
misc: fastrpc: Add dma_mask to fastrpc_channel_ctx
misc: fastrpc: Add mmap request assigning for static PD pool
misc: fastrpc: Safekeep mmaps on interrupted invoke
misc: fastrpc: Add support for audiopd
misc: fastrpc: Rework fastrpc_req_munmap
misc: fastrpc: Use fastrpc_map_put in fastrpc_map_create on fail
misc: fastrpc: Add fastrpc_remote_heap_alloc
misc: fastrpc: Add reserved mem support
misc: fastrpc: Rename audio protection domain to root
...
- a new driver for Cypress Generation 5 touchscreens
- a new driver for Hynitron cstxxx touchscreens
- a new driver for Himax hx83112b touchscreen
- I2C input devices have been converted to use i2c's probe_new()
- a large number of input devices are now using DEFINE_SIMPLE_DEV_PM_OPS
and pm_sleep_ptr() and no longer use __maybe_unused annotations
- improvements to msg2638 touchscreen driver to also support msg2138
- conversion of several input deevine bindings to yaml/DT schema
- changes to select touch drivers to move handling of wake irqs to the
PM core
- other assorted fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCY5d+9wAKCRBAj56VGEWX
nN9CAP9R1zCdPc5Y2PmLnE6JHc9XynPhUnVbnx4zHieMxw0nHQD/ZnHot+Cdq/+L
433dkdX50pwK3XxRQgjRaym+efgwfQ0=
=9m4z
-----END PGP SIGNATURE-----
Merge tag 'input-for-v6.2-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for Cypress Generation 5 touchscreens
- a new driver for Hynitron cstxxx touchscreens
- a new driver for Himax hx83112b touchscreen
- I2C input devices have been converted to use i2c's probe_new()
- a large number of input devices are now using
DEFINE_SIMPLE_DEV_PM_OPS and pm_sleep_ptr() and no longer use
__maybe_unused annotations
- improvements to msg2638 touchscreen driver to also support msg2138
- conversion of several input deevine bindings to yaml/DT schema
- changes to select touch drivers to move handling of wake irqs to the
PM core
- other assorted fixes and improvements.
* tag 'input-for-v6.2-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (165 commits)
Input: elants_i2c - delay longer with reset asserted
dt-bindings: input: Convert ti,drv260x to DT schema
dt-bindings: input: gpio-beeper: Convert to yaml schema
Input: pxspad - fix unused data warning when force feedback not enabled
Input: lpc32xx - allow building with COMPILE_TEST
Input: nomadik-ske-keypad - allow building with COMPILE_TEST
Input: pxa27xx-keypad - allow build with COMPILE_TEST
Input: spear-keyboard - improve build coverage using COMPILE_TEST
Input: tegra-kbc - allow build with COMPILE_TEST
Input: tegra-kbc - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: tca6416-keypad - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: tc3589x - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: st-keyscan - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: sh-keysc - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: qt1070 - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: pxa27x_keypad - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: pmic8xxx-keypad - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: nomadik-ske-keypad - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: mcs-touchkey - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
Input: max7359-keypad - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
...
Single patch fixing a memory leak in an error path.
Fine to queue either for 6.2 if too late for 6.1
-----BEGIN PGP SIGNATURE-----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=38dX
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-6.1d' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
4th set of IIO fixes for 6.1
Single patch fixing a memory leak in an error path.
Fine to queue either for 6.2 if too late for 6.1
* tag 'iio-fixes-for-6.1d' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: fix memory leak in iio_device_register_eventset()
dt-bindings: iio: adc: Remove the property "aspeed,trim-data-valid"
iio: adc: aspeed: Remove the trim valid dts property.
iio: core: Fix entry not deleted when iio_register_sw_trigger_type() fails
iio: accel: bma400: Fix memory leak in bma400_get_steps_reg()
iio: light: rpr0521: add missing Kconfig dependencies
iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw
iio: health: afe4403: Fix oob read in afe4403_read_raw
iio: light: apds9960: fix wrong register for gesture gain
Includes a few late breaking fixes for old issues.
Contains a large set of conversions from i2c probe() to probe_new()
as part of an attempt to finally get rid of the old style probe().
New devices support
* adi,ad74115
- New driver for this complex input/output device with 16 bit ADCs,
14 bit DACs amongst other features.
- A few tidy ups / removal of unused data patches followed.
* adi,adf4377
- New driver for this dual output integer-N phased locked loop and VCO
chip.
* maxim,max30208
- New driver for this high accuracy digital temperature sensor.
* st,lsm6dsx
- Support for LSM6DS016IS (chip specific data)
- Support for ISM330IS (id entry only)
Minor cleanups etc
* adi,adis
- Fix a deadlock on device instance specific mutex.
- Tidy up by calling unlocked form of __adis_initial_startup() in all
cases and dropping the locked version.
* adi,ad4130
- Reference spi-peripehral-props.yaml in the dt-binding.
* adi,ad74413r
- Fix a bug brought on by integer promotion of signed value to unsigned type.
- Add an spi_device_id table to allow module autoloading to work.
- Add support for reset pin.
* adi,ad7606_par
- devm_platform_get_and_ioremap_resource() instead of opencoding.
* adi,ad7923
- Add dt-bindings docs for ad7927 via a fallback to ad7928 and do similar
for ad7924.
* adi,ltc2983
- Drop a now unneeded $ref for -nanoamp property as dt-schema no covers this
unit.
* maxim,max11410
- Fix mask due to repeated use of VREFN instead of one of them being VREFP.
* qcom,spmi-iadc
- Add fallback compatibles to dt-binding.
* renesas,rzg2l
- Document use for RZ/Five SoC.
* st,stm32-adc
- Improved calibration support with error logging and a debugfs
interface to read back the result.
* ti,adc128s052
- Fix an issue with missing data members in the adc128_of_match table that
meant all device were being handled as adc128s052 ADCs.
-----BEGIN PGP SIGNATURE-----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=AUOr
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.2b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
2nd set of IIO new device support, cleanups etc for 6.2
Includes a few late breaking fixes for old issues.
Contains a large set of conversions from i2c probe() to probe_new()
as part of an attempt to finally get rid of the old style probe().
New devices support
* adi,ad74115
- New driver for this complex input/output device with 16 bit ADCs,
14 bit DACs amongst other features.
- A few tidy ups / removal of unused data patches followed.
* adi,adf4377
- New driver for this dual output integer-N phased locked loop and VCO
chip.
* maxim,max30208
- New driver for this high accuracy digital temperature sensor.
* st,lsm6dsx
- Support for LSM6DS016IS (chip specific data)
- Support for ISM330IS (id entry only)
Minor cleanups etc
* adi,adis
- Fix a deadlock on device instance specific mutex.
- Tidy up by calling unlocked form of __adis_initial_startup() in all
cases and dropping the locked version.
* adi,ad4130
- Reference spi-peripehral-props.yaml in the dt-binding.
* adi,ad74413r
- Fix a bug brought on by integer promotion of signed value to unsigned type.
- Add an spi_device_id table to allow module autoloading to work.
- Add support for reset pin.
* adi,ad7606_par
- devm_platform_get_and_ioremap_resource() instead of opencoding.
* adi,ad7923
- Add dt-bindings docs for ad7927 via a fallback to ad7928 and do similar
for ad7924.
* adi,ltc2983
- Drop a now unneeded $ref for -nanoamp property as dt-schema no covers this
unit.
* maxim,max11410
- Fix mask due to repeated use of VREFN instead of one of them being VREFP.
* qcom,spmi-iadc
- Add fallback compatibles to dt-binding.
* renesas,rzg2l
- Document use for RZ/Five SoC.
* st,stm32-adc
- Improved calibration support with error logging and a debugfs
interface to read back the result.
* ti,adc128s052
- Fix an issue with missing data members in the adc128_of_match table that
meant all device were being handled as adc128s052 ADCs.
* tag 'iio-for-6.2b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (178 commits)
iio: addac: ad74413r: fix blank line after declaration warning
iio: addac: ad74115: remove unused ad74115_dac_slew_rate_hz_tbl
dt-bindings: iio: imu: st_lsm6dsx: add ism330is
iio: imu: st_lsm6dsx: add support to ISM330IS
iio: frequency: adf4377: add support for ADF4377
dt-bindings: iio: frequency: add adf4377 doc
dt-bindings: iio: adc: ad4130: use spi-peripheral-props.yaml
dt-bindings: iio: temperature: ltc2983: drop $ref for -nanoamp properties
dt-bindings: iio: adc: renesas,rzg2l-adc: Document RZ/Five SoC
iio: adc128s052: add proper .data members in adc128_of_match table
iio: adc: stm32-adc: add debugfs to read raw calibration result
iio: adc: stm32-adc: improve calibration error log
iio: adc: stm32-adc: smart calibration support
iio: addac: ad74413r: add support for reset-gpio
dt-bindings: iio: ad74413r: add optional reset-gpios
iio: addac: ad74413r: add spi_device_id table
dt-bindings: iio/adc: qcom,spmi-iadc: use double compatibles
dt-bindings: iio: imu: st_lsm6dsx: add lsm6dso16is
iio: imu: st_lsm6dsx: add support to LSM6DSO16IS
iio: addac: add AD74115 driver
...
We have finally managed to take the mlock mutex entirely private so as
to avoid it being used for multiple purposes. Now it is just used to
protect device mode transitions (typically to and from buffered capture).
Includes merge of an immutable i2c branch to get the new
i2c_client_get_device_id() (thanks to Wolfram for providing the branch).
Based on rc3 to pick up some precursor fixes from early in the cycle and
avoid an unnecessarily messy history.
New device support
* adi,ad4310
- New driver to support this very flexible measurement device including
a 24 bit ADC. Later fix for documentation build issue.
* adi,adxl355
- Add support of the ADXL359 accelerometer.
* adi,ltc2983
- Support additional variants of the temperatures sensor:
LTC2984 with an EEPROM
LTC2985, LTC2986 with only 10 channels.
* invensense,icm42600
- Add support for icm42631 (needed only ID and WHOAMI)
* kionix,kx022a
- New driver for this 3 axis accelerometer.
* maxim,max11401
- New driver to support this 24-bit 10 channel ADC.
Includes some new ABI to support configuration of notch filters.
* mediatek,mt6370
- Add new driver to support the ADC part of the mt6370.
* st,lsm6dsx
- Add support for LSM6DSV accelerometer and gyroscope. Simple additional
of chip specific data and IDs.
- Add support for LSM6DSV16X accelerometer and gyroscope. Compatible with
features currently implemented for the LSM6DSV.
* st,stm32-adc
- Add support for stm32pm13x SoCs.
core / subsystem wide:
- Add new IIO_STATIC_CONST_DEVICE_ATTR() which is a dance necessary to
allow for the wrapping of attributes in the code that duplicates them
for multiple buffers.
- Harden against future issues with expectation that all buffer attributes
are iio_dev_attrs by changing the code to take an array of pointers
of the correct type.
- Last transitions of drivers to local locks rather than missuses of mlock.
- Add an iio_device_claim_buffer_mode() callback to avoid a race in the
max30100 driver without directly using mlock.
- Move mlock to the opaque IIO device structure to prevent misuse.
- Add missing spi_device_id tables to support auto loading of modules.
- Update some ADI maintainers in DT bindings.
- A few more moves of bus drivers and core module sets to export
name spaces.
- Extensive use of new devm_regulator_get_enable() and friends.
- Switch a bunch of i2c drivers to probe_new() including the bmp280
which makes use of the new i2c_client_get_device_id() helper to
simplify this change.
dt-bindings:
- More use of spi-peripheral-props.yaml.
Features
* freescale,mpl115
- Use runtime PM to implement shutdown GPIO support.
* melexis,mlx90632
- More sophisticated runtime power management
- Provide access to sampling frequency.
- Trivial follow up fixes.
* microchip,mcp3911
- Support control of PGA.
* st,lsm6dsx
- Add support for software triggers for cases where the IRQ lines
are not wired up.
* vishay,vcnl4000
- Add control of integration time.
Minor cleanups and fixes
* adi,ad4130
- Improve ABI documentation formatting.
- Kconfig dependency fixup.
* adi,ad5758
- Minor dt binding fix.
* adi,ad9834
- Tidy up line breaks.
* adi,ade7854
- Minor improvement in code clarity by replacing a ternary.
* adi,admv8818
- Harden code against hardware returning wrong values.
* adi,adxl355
- Warn only if unknown device ID detected to allow for fall back
device tree compatibles on future devices.
* adi,ltc2983
- dt-bindings clarifications and general improvements.
- Ensure DMA safe buffer for bulk writes without relying on current
regmap implementation choices.
* avago,adps9960
- Fix up a disconnect between event enable attributes and what was
enabled.
* bosch,bma400
- Switch to dev_err_probe() from open coded EPROBE_DEFER handling.
* cosmic,cc10001
- Fully devm managed probe() and related tidying up.
* meas,ms5611
- Add an example of spi-max-frequency.
* meleixs,mlx90632
- Tidy up confusing error return value.
- Style improvements.
* multiplexer
- Switch to dev_err_probe() from open coded EPROBE_DEFER handling.
* qcom,spmi-vadc
- Minor dt binding improvements.
* rockchip,saradc
- Add ID for rv1126.
* semtech,sx9360
- Add SAMM0208 ACPI ID. Doesn't appear to be a valid vendor prefix
but is in the wild.
* st,lsm6dsx
- Factor out common code as _device_set_enable().
- Fix up wrong docs after LSM6DSV addition.
* st,stm32-adc
- Manage the min sampling time on all internal channels.
* trig,sysfs
- Improve error labels.
-----BEGIN PGP SIGNATURE-----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=Fo38
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.2a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, feature and cleanup for 6.2 (take2)
We have finally managed to take the mlock mutex entirely private so as
to avoid it being used for multiple purposes. Now it is just used to
protect device mode transitions (typically to and from buffered capture).
Includes merge of an immutable i2c branch to get the new
i2c_client_get_device_id() (thanks to Wolfram for providing the branch).
Based on rc3 to pick up some precursor fixes from early in the cycle and
avoid an unnecessarily messy history.
New device support
* adi,ad4310
- New driver to support this very flexible measurement device including
a 24 bit ADC. Later fix for documentation build issue.
* adi,adxl355
- Add support of the ADXL359 accelerometer.
* adi,ltc2983
- Support additional variants of the temperatures sensor:
LTC2984 with an EEPROM
LTC2985, LTC2986 with only 10 channels.
* invensense,icm42600
- Add support for icm42631 (needed only ID and WHOAMI)
* kionix,kx022a
- New driver for this 3 axis accelerometer.
* maxim,max11401
- New driver to support this 24-bit 10 channel ADC.
Includes some new ABI to support configuration of notch filters.
* mediatek,mt6370
- Add new driver to support the ADC part of the mt6370.
* st,lsm6dsx
- Add support for LSM6DSV accelerometer and gyroscope. Simple additional
of chip specific data and IDs.
- Add support for LSM6DSV16X accelerometer and gyroscope. Compatible with
features currently implemented for the LSM6DSV.
* st,stm32-adc
- Add support for stm32pm13x SoCs.
core / subsystem wide:
- Add new IIO_STATIC_CONST_DEVICE_ATTR() which is a dance necessary to
allow for the wrapping of attributes in the code that duplicates them
for multiple buffers.
- Harden against future issues with expectation that all buffer attributes
are iio_dev_attrs by changing the code to take an array of pointers
of the correct type.
- Last transitions of drivers to local locks rather than missuses of mlock.
- Add an iio_device_claim_buffer_mode() callback to avoid a race in the
max30100 driver without directly using mlock.
- Move mlock to the opaque IIO device structure to prevent misuse.
- Add missing spi_device_id tables to support auto loading of modules.
- Update some ADI maintainers in DT bindings.
- A few more moves of bus drivers and core module sets to export
name spaces.
- Extensive use of new devm_regulator_get_enable() and friends.
- Switch a bunch of i2c drivers to probe_new() including the bmp280
which makes use of the new i2c_client_get_device_id() helper to
simplify this change.
dt-bindings:
- More use of spi-peripheral-props.yaml.
Features
* freescale,mpl115
- Use runtime PM to implement shutdown GPIO support.
* melexis,mlx90632
- More sophisticated runtime power management
- Provide access to sampling frequency.
- Trivial follow up fixes.
* microchip,mcp3911
- Support control of PGA.
* st,lsm6dsx
- Add support for software triggers for cases where the IRQ lines
are not wired up.
* vishay,vcnl4000
- Add control of integration time.
Minor cleanups and fixes
* adi,ad4130
- Improve ABI documentation formatting.
- Kconfig dependency fixup.
* adi,ad5758
- Minor dt binding fix.
* adi,ad9834
- Tidy up line breaks.
* adi,ade7854
- Minor improvement in code clarity by replacing a ternary.
* adi,admv8818
- Harden code against hardware returning wrong values.
* adi,adxl355
- Warn only if unknown device ID detected to allow for fall back
device tree compatibles on future devices.
* adi,ltc2983
- dt-bindings clarifications and general improvements.
- Ensure DMA safe buffer for bulk writes without relying on current
regmap implementation choices.
* avago,adps9960
- Fix up a disconnect between event enable attributes and what was
enabled.
* bosch,bma400
- Switch to dev_err_probe() from open coded EPROBE_DEFER handling.
* cosmic,cc10001
- Fully devm managed probe() and related tidying up.
* meas,ms5611
- Add an example of spi-max-frequency.
* meleixs,mlx90632
- Tidy up confusing error return value.
- Style improvements.
* multiplexer
- Switch to dev_err_probe() from open coded EPROBE_DEFER handling.
* qcom,spmi-vadc
- Minor dt binding improvements.
* rockchip,saradc
- Add ID for rv1126.
* semtech,sx9360
- Add SAMM0208 ACPI ID. Doesn't appear to be a valid vendor prefix
but is in the wild.
* st,lsm6dsx
- Factor out common code as _device_set_enable().
- Fix up wrong docs after LSM6DSV addition.
* st,stm32-adc
- Manage the min sampling time on all internal channels.
* trig,sysfs
- Improve error labels.
* tag 'iio-for-6.2a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (146 commits)
iio: pressure: bmp280: convert to i2c's .probe_new()
iio: imu: st_lsm6dsx: fix LSM6DSV sensor description
iio: adc: ad4130: depend on GPIOLIB
staging: iio: meter: replace ternary operator by if condition
iio: light: apds9960: Fix iio_event_spec structures
dt-bindings: iio: imu: Add inv_icm42600 documentation
iio: imu: inv_icm42600: Add support for icm42631
dt-bindings: iio: adc: rockchip-saradc: Add saradc for rv1126
dt-bindings: iio: dac: adi,ad5758: Drop 'contains' from 'adi,dc-dc-mode'
dt-bindings: iio: imu: st_lsm6dsx: add lsm6dsv16x
iio: imu: st_lsm6dsx: add support to LSM6DSV16X
iio: proximity: sx9360: Add a new ACPI hardware ID
iio: temperature: mlx90632: Add missing static marking on devm_pm_ops
iio: temperature: mlx90632: Add error handling for devm_pm_runtime_enable()
iio: temperature: ltc2983: support more parts
dt-bindings: iio: temperature: ltc2983: support more parts
dt-bindings: iio: temperature: ltc2983: use generic node name in example
dt-bindings: iio: temperature: ltc2983: describe broken mux delay property
dt-bindings: iio: temperature: ltc2983: refine descriptions
dt-bindings: iio: temperature: ltc2983: change default excitation for custom thermistors
...
Checkpatch wants a blank line after all declarations. Add it now,
even though the patch has already been submitted.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20221124153049.8851-1-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This table was supposed to be used for handling the DAC rate, but it
ended up being unused. Remove it.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20221124152559.7895-1-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Prior to commit bd5d54e4d4 ("iio: adc128s052: add ACPI _HID
AANT1280"), the driver unconditionally used spi_get_device_id() to get
the index into the adc128_config array.
However, with that commit, OF-based boards now incorrectly treat all
supported sensors as if they are an adc128s052, because all the .data
members of the adc128_of_match table are implicitly 0. Our board,
which has an adc122s021, thus exposes 8 channels whereas it really
only has two.
Fixes: bd5d54e4d4 ("iio: adc128s052: add ACPI _HID AANT1280")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221115132324.1078169-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add more information in calibration error log to differentiate
single-ended and differential calibration.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20221115103124.70074-3-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add smart calibration support for STM32MP1.
- STM32MP15x: both linear & offset calibration are supported
- STM32MP13x: Only offset calibration is supported
Linear calibration:
Linear calibration is SoC dependent and does not change over time
so it can be done only once.
Linear calibration may have already been done in u-boot.
Skip calibration execution if calibration data are already available.
Save calibration factors in private data and restore them from private
data on next ADC start.
Offset calibration:
This calibration may vary over time, depending on temperature or voltage.
Run offset single-ended and differential calibration on each ADC start,
as it is not time consuming. This calibration do not need to be saved.
So, remove calfact_s and calfact_d value and bitfields that are no
longer used.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20221115103124.70074-2-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a board where the reset pin of the ad74412 is connected to a
gpio, but also pulled low (i.e., asserted) by default. Hence to get
the chip out of reset, the driver needs to know about that gpio and
deassert the reset signal before attempting to communicate with the
chip.
When a reset-gpio is given in device tree, use that instead of the
software reset. According to the data sheet, the two methods are
functionally equivalent.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20221115095517.1008632-4-linux@rasmusvillemoes.dk
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD74115H is a single-channel, software-configurable, input and
output device for industrial control applications. The AD74115H
provides a wide range of use cases, integrated on a single chip.
These use cases include analog output, analog input, digital output,
digital input, resistance temperature detector (RTD), and thermocouple
measurement capability. The AD74115H also has an integrated HART modem.
A serial peripheral interface (SPI) is used to handle all communications
to the device, including communications with the HART modem. The digital
input and digital outputs can be accessed via the SPI or the
general-purpose input and output (GPIO) pins to support higher
speed data rates.
The device features a 16-bit, sigma-delta analog-to-digital converter
(ADC) and a 14-bit digital-to-analog converter (DAC).
The AD74115H contains a high accuracy 2.5 V on-chip reference that can
be used as the DAC and ADC reference.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221117080916.411766-3-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The constant AD74413R_ADC_RESULT_MAX is defined via GENMASK, so its
type is "unsigned long".
Hence in the expression voltage_offset * AD74413R_ADC_RESULT_MAX,
voltage_offset is first promoted to unsigned long, and since it may be
negative, that results in a garbage value. For example, when range is
AD74413R_ADC_RANGE_5V_BI_DIR, voltage_offset is -2500 and
voltage_range is 5000, so the RHS of this assignment is, depending on
sizeof(long), either 826225UL or 3689348814709142UL, which after
truncation to int then results in either 826225 or 1972216214 being
the output from in_currentX_offset.
Casting to int avoids that promotion and results in the correct -32767
output.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Fixes: fea251b6a5 (iio: addac: add AD74413R driver)
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221118123209.1658420-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/202211220935338446115@zte.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16400_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-7-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16260_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-6-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16136_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-5-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16209_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-4-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16201_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-3-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add '__adis_enable_irq()' implementation which is the unlocked
version of 'adis_enable_irq()'.
Call '__adis_enable_irq()' instead of 'adis_enable_irq()' from
'__adis_intial_startup()' to keep the expected unlocked functionality.
This fix is needed to remove a deadlock for all devices which are
using 'adis_initial_startup()'. The deadlock occurs because the
same mutex is acquired twice, without releasing it.
The mutex is acquired once inside 'adis_initial_startup()', before
calling '__adis_initial_startup()', and once inside
'adis_enable_irq()', which is called by '__adis_initial_startup()'.
The deadlock is removed by calling '__adis_enable_irq()', instead of
'adis_enable_irq()' from within '__adis_initial_startup()'.
Fixes: b600bd7eb3 ("iio: adis: do not disabe IRQs in 'adis_init()'")
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
VREFP bit was missing from channel configuration mask and VREFN bit was
included twice instead which fails to enable positive reference buffer when
requested by a channel. Channels that don't enable vrefp buffer were not
affected.
Fixes: a44ef7c460 ("iio: adc: add max11410 adc driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Link: https://lore.kernel.org/r/20221122114718.17557-1-Ibrahim.Tilki@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-191-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-190-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-189-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-188-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-187-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Crt Mori<cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-186-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-185-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-184-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-183-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-182-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-181-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-180-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-179-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-178-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-177-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-176-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-175-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marek Vasut